GE (N) P/TOKEN- 23 OF 2020-2021 PROVISION OF CERTAIN LBW, RW AND SPECIAL REPAIR WORKS IN THE AREA OF AGE B/R (EAST) UNDER GE (NORTH) PUNE

Amount

Excavation in trenches not exc. 1.5 m wide and not exc. 1.5 m in depth for foundation, cable etc. or for shafts, wells, cesspits, manholes, pier holes, pole etc. n. exc 10 sq m on plan and getting out in soft/ loose soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick with soils complete all as specified and as directed.

Removing of excavated material (soil) to distance not exc.50metres and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Removing of excavated material (soil) to distance exceeding 150m and not exc.250metres and deposited where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D-2 (using 40 mm graded broken stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in surface channels and drainscomplete all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in lintels upto 1.5m clear span, seismic and other similar bands, cills, plinth courses, kerbs, parapets, coping, benching, coping, hold fast blocks, bed blocks/ bed plates etc. including weathering, slightly rounded or chamfered angles and throating including necessary form work all as specified and as directed.

Material and labour for RCC (design mix) M-25 (using 20mm graded broken stone aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, complete all as specified and as directed.

Material labour for RCC (design mix) M-25 (using 20mm graded broken stone aggregates) as in columns, pillars, piers,posts and struts complete all as specified and as directed.

Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified ans as directed.

M&L Brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

All as per Srl item No. 11 above but except bricks

Material and labour for formwork to sides of concrete foundations, footings, bases of column, raft and raft beams, side and soffit (if any ) of foundation and plinth beam and similar works, vertical or batter etc for rough finished flat surfaces of concrete complete all as specified and directed.

Material and labour for formwork to sides of pillars, posts, struts, columns and stanchions, square, rectungular or polygonal for fair finished flat surfaces of concrete complete all as specified and as directed.

Supply and fix for 2nd class hard wood boarding, 20mm thick, planed one side with butt joints and fixed with nails in any situation as in eaves board complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from frame) area exc.1.5 sqm and not exc.4 sqm each complete all as directed

Supply and fix factory made solid PVC Moulded Door Shutter, 28 to 30 mm thick (stiles), with particle board core, with 2,4, or 6 raised panel design with 5mm thick 3D wood grain Moulded PVC Sheet polyurethane painted on the front face & 5 mm thick prelam PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing given in MES SSR part -I and II.

Factory made fully glazed/wire gauge (single piece Both side) PVC prelam door shutter 33 to 35mm thick consisting of frame made up of MS tube of size 25mm X 25mm (19 guage) for top & bottom rail, and in styles. Single piece plane coloured PVC sheets of 5mm thick to be used to cover style & rails. For edges, PVC sheets strip of 20mm thick struck inside with solvent cement. Plane colour PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert with PVC board 22mm to 25 mm thick solid core board . Panel shall be of wire gauge stainless steel wire cloth 0.36mm nominal dia of wire and everage width of aperture 1.4mm, stainless steel wire cloth shall be covered with aluminium XPM in rhombus shape in one piece from top to bottom rail, fixed with self tapping screw not less then 38mm long complete all as specified and directed by Engineer-in-Charge.

Supply and fix for 250mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and as directed.

Supply and fix, 300mm, mild steel, ordinary rat tail rod pattern spring (helical door spring) including roller and roller plate complete all as specified and as directed.

Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. or securing with clips complete all as specified and as directed.

Supply and fix for rolled mild steel section Fe 410-W(Gde-E-250) quality A as in main and cross beams, hip and jack rafters, purlins connected to common rafters and running rails and guides for sliding doors, column posts, wind ties, fixed with angle cleats or other connecting plates, drilled for fixing all as specified and directed.

Supply and fix for rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening,conforming to Fe-290 Grade-E-165 complete all as specified and as directed.

S&F Factory made 100 % solid wood plastic composite (WPC) door frame, double rebate 125 mm x 45 mm made from wood plastic composite ( Single executed process) material with density 780 Kg/ Cum, all as specified and directed.NOTE: During Fixing of chowkhat, surface Shall be make good in plumb with existing finishes like cement plaster, similar wall tile,floor tile etc and as per site requirement.

Supply and fix for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 120gms/ Sqm complete all as specified and as directed.

Supply and fix (Except sheeting) for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc with grade of zinc coating 120gms/ Sqm complete all as specified and as directed.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete all as specified and as directed.

Supply and fix for 0.50mm thick pre-painted galvalume aluminium zinc coating (AZ-150) GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall fixed with self tapping screws with side lap complete all as specified and as directed.

Material and labour for Roof tiles Mangalore pattern interlocking at side joints, laid dry complete all as specified and as directed.

M&L for Roof tiles (Except tiles) Mangalore pattern interlocking at side joints, laid dry complete all as specified and as directed. (Note : Serviceable tiles obtained from dismantled shall be re-used.)

Material and labour for ridge or hip tiles to suit Manglore pattern of roofing tiles, bedded and jointed in cement mortar (1:6) etc including dismantling of tiles complete all as specified and as directed.

Supply and fix for tiled false ceiling of size (600x600)mm in true horizontal level suspended on inter locking Gyproc Matrix metal grid of hot dipped galvanized steel sections. It consists of main "T" runner of size 24x38x0.3x 3600mm, cross "T" of size 24x25x0.3x 1200mm, secondary cross "T" of size 24x25x0.3x 600mm and PPGI wall angle of size 24x24x0.4x 3000mm. Bottom exposed capping of width 24 mm of all T-sections shall be of 0.25mm thick PPGI. PPGI wall angle 24x24x0.4x 3000mm {Material-GI(IS513),YS-280Mpa,Finish-Galvanised 90GSM(IS277)} is fixed along the perimeter of the ceiling to Walls, partitions or columns etc., with wooden screws at 300mm centers or Hilti HPS 6 x40mm placed at 600 mm c/c. Gyproc ® soffit cleat 27x37x25x1.6mm {GI(IS513)YS-260Mpa,Finish-Galvanised 120GSM(IS277) } is fixed with Gyproc® Rawl Plug- Ø8x45mm {Material-IS 513 CR2 grade, Zinc coating (7 to 8 microns) pull out load- 6.8kN for M30 concrete grade} creating 1200mm x 1200mm grid. Main-T runners 24x38x0.3x3600mm are then suspended at 1200mm c/c from ceiling using 4mm zinc electroplated butterfly level clips of size 85x30x0.8mm spaced at maximum 1200mm center to center along main T and not more than 150mm from spliced joints.

The last hanger at the end of each main runner should not be greater than 600mm from the adjacent wall/ hung from ceiling using 2mm dia. G.I. suspension wires and 'J' bolts, washers, nuts spaced at 1200 mm both ways as per site requirement. 24x25x0.3x 1200mm cross T {GI(IS513)YS-280Mpa,Finish-Galvanised 120GSM (IS277) } is interlocked between the main T at 600mm center to center to form a grid of 1200x 600 mm and then secondary cross “T" 24x25x0.3x600mm {GI(IS513)YS-280Mpa,Finish-Galvanised 120GSM(IS277) } is then interlocked at middle of the 1200x600mm grid to form grids of 600x600mm. Cross Tees at the ends having length more than 600mm are to be supported independently. Finally 9.5mm thick square edge Gyproc Polyshield Gypsum tile of size 595x595mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges, so as to make the tile a completely sealed unit, is placed in the grid including making niches for fans/ light complete all as specified and as directed. Make: Gyproc-Saint Gobain of equivalent of Armstrong, Diaken, New Age (ACE) as approved by GE.

Material and labour for light shade double charged vitrified ceremic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exc. 0.36Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and shade/ pattern as approved by GE over and including 15mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour for coloured, light shade, vitrified ceramic tiles, polished of required size, 10 mm thick as in skirting/dado, shade/ pattern as approved by GE, set and jointed in neat cement slurry using grey cement and pointed in white or coloured cement to match the colour of tiles over and including 10 mm thick rendering in cement mortar (1:3) complete all as specified and as directed.

Material and labour for rendering 15mm thick in CM (1:6) on fair faces of brickwork or concrete surfaces and provn of sagol finish complete all as specified and as directed.

Material and labour for rendering 15mm thick in cement mortar (1:4) on fair faces of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

Taking down cement plaster any description on brick/ block/ stone walls, roof etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Material and labour for preparation of newly plastered or unplastered wall surfaces and applying two coats of oil bound/ emulsion distemper over a coat of priming paint and white cementitious wall care fine putty 1 to 1.5mm thick complete all as specified and as directed.

Material and labour for complete removal of existing treatment on walls, preparation of surfaces and make the surfaces free from loose particles, oil stains etc., preparing surfaces and applying two coats of oil bound/ emulsion distemper over a coat of primer complete all as specified and as directed.

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint over a coat of cement primer complete all as specified and as directed

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and as directed

Material and labour for preparation of new steel or iron surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

Demolition of brick work/ precast concrete block walling/ boulder masonary, built in cement mortar or cement lime mortar including all quoins, pillars etc. complete all as directed.

Dismantling timber scantlings, unframed work, 40 sq. cm and over in section, in any position complete all as directed.

Dismantling wooden boarding/ plywood of any description and any thickness including fillets fixed in any position with nails complete all as directed.

Dismantling battens for tiles, shingles etc. of any size including tiling fillets spaced exceeding 15cm complete all as directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness sheets including Nainital or similar pattern roof coverings complete all as directed.

Dismantling asbestos cement (corrugated, semi corrugated etc.) sheets in roof coverings complete all as directed.

Dismantling single layer Mangalore pattern or similar tiles in roofing including complete all as directed.

Dismantling of wall/ceiling board/POP ceiling of any description and any thickness including cover fillets/ grid etc complete all as directed.

Supply and fix for mild steel galvanised chain link fencing of 3mm dia GI wire, 75mm x 75mm mesh size and weight not less than 2.5Kg per Sqm conforming to IS: 2712, galvanised coating of type heavy as laid down in IS: 4826 including line wires fixing to any type of standards, rails, straining bolts etc. including provision of binding wire, make as approved by GE complete all as specified and as directed.

Supply, laying and testing for LT XLPE UG cable insulated screened PVC bedded galvanised steel strip or wire armoured, heavy duty electric power cables with stranded aluminium conductor with cable glands, lugs etc fixed on wall/ pole including brass cable glands, clamps etc. of size 25 Sqmm 4 core cable complete all as specified and as directed.

Supply and laying 40mm outer dia, double walled corrugated (DWC) HDPE duct pipe conforming to IS- 14930 Pt-II with antirodent and non flame propogating properties of approved colour complete with fittings for cable protection complete all as specified and as directed.

Taking down carefully unserviceable point wiring of any description/ type/ size of light/ fan / tube/ power / two way/ bell etc. on TW batten/ conduit including removal of batten/ conduit/ gutties/ wooden boards/ switchs/ sockets/ regulators/ holders/ ceiling roses/ call bells/ light fittings etc. and making good the disturbed surfaces of wall/ ceiling so as to match with the existing finishes complete all as directed.

Taking down the existing unserviceable main switch/ cut out/ MCB DBs/ sheet metal enclosure of any type/ capacity/ description as existing at site including MCBs any type/ capacity and making good the disturbed surfaces of wall/ ceiling to match with the existing finishes complete all as directed.

Material and labour for point wiring using approved colour coding as per IS, with multistranded FRLS copper conductor 1.5 Sq. mm (nominal area), two single core PVC insulated and unsheathed multistranded cable 1100 volts grade ISI-694 marked through and including heavy duty ISI marked, 20 mm dia rigid PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ ceiling etc, with concealed GI terminal sunken boxes 1.2mm thick 60mm deep of suitable size as per site requirement, covered with modular white cover plate with frame suitable for housing modular switches, sockets, regulators etc. including PVC insulated multistranded FRLS copper conductor 1.5 Sqmm (nominal area) single core cable as earth continuity conductor and connecting to the common earth dolly for one light point controlled by one, one way switch 5 Amps complete all as specified and as directed.

All as per serial item No.59 here-in-before but point wiring for one ceiling/ exhaust fan point controlled by one, one way switch 5 Amps and regulator.

All as per serial item No.59 here-in-before but point wiring for one 3 pin 5 Amps socket outlet controlled by one switch on same board.

All as per serial item No.59 here-in-before but point wiring for one 3 pin 5 Amps socket outlet controlled by one switch on independent board.

All as per serial item No.59 here-in-before but point wiring for one bell point controlled by one bell switch 5 Amps.

All as per serial item No.59 here-in-before but with FRLS copper conductor 2.5 Sqmm (nominal area), single core, PVC insulated and unsheathed multistranded cable 1100 Volt grade ISI-694 marked including PVC insulated multistranded FRLS copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor for 3 pin 15 Amps socket outlet on independent board.

Supply and fix for lamp holder, PVC body/ polycarbonate type with back plate suitable batten/ slanting fittings complete all as specified and as directed.

Supply and fix for modular switch, one way 6 Amps, 1 module complete all as specified and as directed.

Supply and fix for modular switch, one way, 16 Amprs, 1 module with neon indicator complete all as specified and as directed.

Supply and fix for modular bell push, 6Amps, 1 module complete all as specified and as directed.

Suply and fix for bell electric ding dong type suitable for operation on 230 volt 50 HZ A C supply including taking down existing complete all as specified and as directed

Supply and fix for modular socket outlet multi purpose 2/3 pin 6 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular socket outlet multipurpose, 3 pin 6 Amps and 3 pin 16 Amps, combined 2 module complete all as specified and as directed.

Supply and fix for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed.

Supply and fix for sheet metal enclosure MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/ stone masonry etc and making good of disturbed surface to match with existing colour of wall, connecting complete all as specified and as directed.

Supply and fix for MCB SPN rated capacity 40 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for MCB SP rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for MCB TPN rated capacity 63Amps, 415Volts breaking capacity 10 KA 'C' curve complete all as specified and as directed.

Supply and fix for ceiling rose, 3 terminals, PVC/ polycarbonate type, isolated body suitable ISI marked complete all as specified and as directed.

Supply and fix for wall mounted LED 18 watts with lumens out put not less than 1800 lumens, box type (decorative) light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and integrated electronic driver connector block etc complete with all accessories internally pre wired all as per Cat No. BLRB-DB118 & BLRB 18W CWc of make Bajaj or equvalent of make Philips/ Wipro/ Havells/ Syska/ Jaguar as approved and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED tube 4' x 18 watts complete all as specified and as directed.

Supply and fix for recessed mounted low depth LED luminaire 2'x2' square LED panel 36 watts aesthetically designed and 4x1 flat panels to enhance the delight of occupants with classic design and glare free soft illumination operating voltage 140-270 volts, AC, 50 Hz all as per Cat No.BZRSQL 36W GZ1 WH of make Bajaj or equivalent of make Philips/ Wipro/Jaquar/ Crompton as approved complete all as specified and as directed.

S&F ceiling fan 1200mm sweep BEE 5 star rated, ISI marked 240 volt AC 50 HZ single phase with hanging rod, conopy set, clamps, bolts nuts and connecting with three core flexible PVC copper conductor cable of size 1.50 sqmm from ceiling rose to fan complete all as specified and directed. Make: Havells Cat No. ES-50 or Bajaj cat No. Kessals 50 ISI of equivalent of Usha, Orient, Crompton.

S&F for wall mounted fan of size 450mm sweep 240 volt AC 50 HZ single phase and connecting with three core flexible PVC copper conductor cable of size 1.50 sqmm from ceiling rose or connecter to fan complete all as specified and directed. Make: Bajaj Model Midia BW 2200 or equivalent of Usha, Orient, Crompton, Havells.

Material and labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less then 2.25 meter deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel and connected to main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm including 8mm dia TMT bars both ways with one handle for lifting made out of 8mm dia MS bar, funnel, wire mesh, 20 mm bore galvanized steel tubing (medium grade) for watering, filling charcoal or coke and salt in alternate layers, 15mm bore galvanized steel tubing light grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No.3 of SSR Part-I including taking out existing earthing . (Note: GI earth wire and protection pipe upto 7.5metres shall be deemed to be included in quoted rate)

Note : 1. Rerformance security:- Refer Condition 22 of Special Conditions. 2. Quoted Contract Sum shall be arrived at after deducting the amount of Credit Schedule (refer Schedule of Credit in pdf form for quantity, rate and amount etc.) for old unserviceable materials retrieved from site.

ANIL CONSTRUCTION CO.

VIRENDRA FABRICATORS

Gauri Associates

M/S Sharvi Construction