GE 861 EWS-54/2023-24

Amount

Demolition of cement concrete (unreinforced) in ground floors & paving n.exc 15 cm thick (below or above ground level) complete all as specified and directed.

Taking down cement plaster on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Surface excavation not exc 15cm deep and getting out in soft/ loose soil, complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises,complete all as specified and directed.

Demolition wall and ceiling boards (fibre, Pulp, insulation etc) or insulation board/slabs/blankets, any thickness, including cover fillets etc, complete all as specified and directed.

Dismantling timber scantling unframed 40 sq cm and over in section in any position, complete all as specified and directed.

Dismantling of timber scantling under 40 Sqcm, fixed in any position in fillet rails, posts rafters purlin etc complete all as specified and directed.

Taking down chowkats or frames with shutters (w/o taking off shutters from the frame) exc 1.5 but n exc n.exc 4 Sqm each, complete as specified and directed.

Dismantling plain or corrugated steel sheeting , any gauge and thickness, including Nainital or similar pattern roof coverings, complete all as specified and directed.

Excavation in trenches n exc 1.50m wide and n exc 1.50m in depth for foundation etc or for shaft wells, cesspits manholes pier holes etc n. exc 10 sqm on plan and n. exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and directed.

Returning filling in (soil) including spreading, levelling , watering and well ramming in layers n exc 25cm thick, complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 mtr and depositing where directed at a level n exc 1.5 mtr above the starting point, complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

RCC (Design mix) M-25 (using 20mm graded aggregates) in columns, pillars, pier post and struts etc complete all as specified and directed by Engr-in-Charge.

RCC M-25 design mix using 20 mm graded aggregate in foundations, including rafts, footings, foundation beams, plinth beams, base for columns, etc basements slabs under rammed piles and mass concrete complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed.

RCC M-25 design mix using 20 mm graded aggregate as in slab supported on walls, beams and columns in floors, roofs landings balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to sides of concrete foundations, footings, bases of columns, raft beams sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

Form work to sides and soffits of floor or roof beam haunching , lintels, cantilevers shelves including supports overhangs etc also splays between floors and beams, etc complete all as specified and directed.

Formwork to sides of concrete pillars, posts, struts, pier, columns and stanchions and similar wk, vertical or to batter complete all as specified and directed by Engr-in-Charge.

Form work to sides and soffits of suspended slab such as roof slab, floor slab, shelves and similar works n. exc. 200 mms thick (Horizontal or sloping), finishing rought the concrete surfaces, complete all as specified and directed.

MS TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not les than 0.9 mm dia or securing with clips quality conforming to complete all as specified and directed.

Reinforcement TMT Steel bars of grade Fe-500/Fe-500 D of 6 to 8mm dia , cut to length, bent to shape required, incl cranking,bending , spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clip complete all as specified and directed.

MS TMT Bars 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders, cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and binding with and including MS wire annealed not less than 0.9 mm dia or securining with clip complete all as specified and directed.

Hard core of broken stone or boulders of guage n. exc 63mm, deposited, spread and levelled in layers n. exc 15 cm thick, watered and rammed to a true surface, complete all as specified and directed.

Precast cement concrete type C-1(using 16mm graded crushed stone aggregate) hollow block masonry with hollow blocks exceeding 10cm in width and setting in mortar 1:6, complete all as specified and directed.

M&L for brick work with sub class "B" bricks, old size, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

M&L for brickwork with sub class 'B' bricks, old size, straight or curved on plan exc 6 mtr mean radius, half brick thick wall, built in Cement Mortar 1:6, complete all as specified and directed by Engr-in-charge.

15mm thick rendering on fair faces of brick work or concrete surfaces in Cement Mortar 1:6 finished the surface even and smooth without using extra cement, complete all as specified and directed.

10mm thick rendering on fair faces of brick work or concrete surfaces in Cement Mortar 1:4 finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on brick work or concrete surfaces, finished the surface even and smooth without using extra cement, complete all as specified and directed.

Plain cement concrete M-10, 1:3:6, type C-2, using 40mm graded mechanically crushed stone aggregate, 75mm thick, as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified and directed. Note:- The unit rate include for use of form work (straight or curved).

75mm thick PCC 1:3:6 Type C-2 (40 mm graded stone aggregate) as in sub-base of floors, complete all as specified and directed.

25mm thick PCC 1:2:4, type B-0 (using 12.5 mm graded crused stone aggregate) as in floors to recieve floor finishes, complete all as specified.

Cement concrete 1:3:6 type C-1 (using 20mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork, complete all as specified and directed.

M&L for PCC 1:2:4, Type B-1, using 40mm graded stone aggregates as in surface channels and drain etc, complete all as specified and directed.

Precast reinforced cement concrete type 1: 2: 4, type-B1 (20 mm graded aggregate) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set and jointed in CM 1:4, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds,mitred/stopped ends etc. complete all as directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.06 sqm but not exc 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in Cement Mortar 1:6, complete all as specified and directed.

Non-skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6, complete all as spcified and directed.

Glazed ceramic coloured tiles 450mm x 350mm x 7mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed.

S&F Granite (of any type) 20mm thick work (table rubbed and polished) in steps, jambs,pillars,window-cills,cokking plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, and including 10 mm thick screed bed in Cement Mortar 1:6 complete all as specified as directed by Engr-in- Charge.

Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

Rolled mild steel in roof trusses (framed),trussed ,purlins,crane girders,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W (Gde-E-250) quality-A, complete all as specified and directed.

S&F 2nd class hardwood, plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified and directed.

S&F 35 mm thick, factory made glazed and skeleton shutters of 2nd class hard wood (Sal/ Hollock) open rebated and prepared to receive glass or gauge,etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing gauge sizes of members of shutters as specified in SSR Part-I Section-8, clause 8.24 (a) for door shutter, supplied and fitted to chowkats, complete all as specified and directed.

S&F 35 mm thick, factory made, plain framed, panelled shutters of 2nd class hard wood (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneers on both faces. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 30mm, plain framed, panelled shutters 1st class hardwood of (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats, complete all as specified and as directed.

M&L for 25mm thick Prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screws to timber frame complete all as specified and directed.

Factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed.

Factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rails and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to in stiles & rails with suitable PVC sheet beading and joinned together with solvent cement supplying & fixing in frames at site as per specification and drawing shown in SSR Part -II, complete all as specified and directed.

S&F PVC insulation panel with EPS stuck 10mm plain PVC sheet suitably placed in existing/ new false ceiling grid made of Aluminum/G.I/M.S/wooden with thickness of PVC insulation panel 10 mm including anodised aluminium snap grid of size 605 mm x 605 mm frame work for false ceiling including supporting hangers complete all as specified and as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as specified and as directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complte all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in ceiling flat and sloping with nails to timber frame, complete all as specified and directed.

4mm thick veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face, fixed in wall flat and sloping with nails to timber frame, complete all as specified and directed.

2nd class hardwood plain fillets square/rectangular or triangular in section of sectional area exc 13 Sqcm but n exc 25 Sqcm, complete all as specified and directed.

2nd class hardwood plain fillets square/rectangular or triangular in section of sectional area exc 3 Sqcm but n exc 6 Sqcm, complete all as specified and directed.

2nd class hardwood plain fillets bull nosed splayed chamfered or rounded on one edge or face in section of sectional area not exc 3 Sqcm, complete all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour as approved having tensile strength of 550 Mps as in roof covering /cladding to wall, fixed with self tapping screws as specified and directed.

150mm long, aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

125mm long, aluminium handles, cast type, anodised, all as specified and directed.

150mm long, aluminium handles, cast type, anodised, all as specified and directed.

100mm long, mild steel cold rolled butt hinges, medium weight, complete all as specified and directed.

250mm size aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F 75mm butt hinges, cast brass with mild steel hinge pin B-11, medium weight complete all as specified and directed.

S&F 100mm extruded brass handles, fabricated type polished complete all as specified and directed.

S&F mild steel window or ventilator, fixed type, with glazing bars complete all as specified

S&F Brass Locks 2 levers for cupboard, grade I, size 50mm complete all as specified and directed.

S&F Magnetic catches of 50/30mm size for cupboard shutters etc complete all as specified and directed.

S&F in repair stainless steel sink with draining board made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mmx330mmx160mm complete.

S&F in repair 15mm bore bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule, complete all as specified and directed.

S&F in repairs 15mm sink mixer for mixing hot & cold water screwed down for iron pipe and fixed complete.

Steel water tubing, 15mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Steel water tubing, 20mm bore, galvanised, "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor, complete all as specified and directed.

Rotational moulded polythylene 1000 litres capacity water storage tank (Cylindrical vertical with closed top), 3 layer hoisted and fixed in position including 20mm brass ball valve high pressure with brass rod & high density plastic ball, complete all as specified and directed.

S&F Vitreous China squatting pan (Orissa pattern)580x440 mm , white with integral foot rests (incl 10 Ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed by Engr-in-Charge.

Vitreous china, wash hand basin, white, flat back, of size 550mmx400mm with brackets including cutting for and pinning in ends of brackets, complete all as specified or erecting stand including 32mm waste fittings, chromium plated with long screwed shanks & fly nuts, flange end bedded in red lead cement and other end fixed, complete all as specified and directed.

Vitreous china soap tray, white, size 160mm x160mm x 90mm embedded in the wall, complete all as specified and directed.

PVC connection 15mm size with PTMT nuts of length 600mm, complete all as specified and directed.

15mm bore pillar tap, fancy type, cast copper alloy, with capstan head, chromium plated screwed down high pressure, with or without lettered hot/cold with long screwed shanks and fly nuts screwed for iron pipe, complete all as specified and directed.

15mm bore bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,complete all as specified and directed.

15mm bore stop valves, fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or union, complete all as specified and directed

15 mm bore brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixeds, complete all as specified and directed.

Supply, fixing, jointing and testing, 20mm bore gun metal globe/gate valve with iron wheel head, both ends screwed for iron pipe, complete all as specified and directed.

Sheet glass shelf assembly 12cm wide consisting of 5.5mm thick glass with CP bracket guard and railing 60cm long, complete, all as specified and directed.

Swivel shower of PTMT any colour for fixing with 15mm pipe, complete all as specified and directed.

S&F towel rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (minimum weight 170 gms) complete all as specified and as directed.

Shower arm 15mm size, 195mm long with bend of 45 degree with flange of PTMT any colour, complete all as specified and directed.

110mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

75mm bore dia PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed.

110mm bore dia PVC (SWR) bends, complete all as specified and directed.

75mm bore dia PVC (SWR) bends, complete all as specified and directed.

110mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed.

75mm bore dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

75mm bore pipe PVC (SWR) vent cowl and fixed, complete all as specified and directed.

M&L PVC SWR floor trap, with grating including joining to waste pipe fixed in cement concrete type B-1 (1:2:4) 75mm dia complete all as specified and directed by Engr-in-Charge.

M&L for concrete bed to drain pipes 150mm bore including packing under,and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate, complete all as specified and directed.

150mm bore reinforced concrete pipes, class NP3, laid and jointed complete with collars, complete all as specified and directed.

Construction of on site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for for 10 users complete all as specified and directed.

Construction of soakage well for users, excavation in ordinary soil, foundation PCC 1:3:6 wells of honey combed and solid in M-25 concrete, including intercepting chamber chamber screen chamber, brick work CM 1: 4, RCC cover slab in M-25/ RR masonry filling with brick bats, complete of size 1.20m dia 3.0 m deep as shown in drg complete all as specified and directed. Drg No CESZ/TD-01/2015 Sheet 3/3.

M&L preparation of newly plaster surface and applying three coat of white wash complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of wall and applying two coats of cement base paint over a coat of alkali-resistant priming coat, complete all as specified and directed.

Preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Preparation of old wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying one coat of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Taking down carefully aluminium/copper point wiring (light fan socket or power) complete with fitting such as switches, tube lights, ceiling rose, pendants, regulators, MCB DB, MCB'S, Main switch from control board and making good disturbed surfaces of walls, floor to match with existing and keeping items aside in safe custody for reuse such as regulators, light fitting, MCBs all as specified and directed.

M & L for point wiring for one light point/fan point controlled by one switch with 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC FRLS insulated unsheathed copper conductor single core cable (green colour) as earth lead in and including PVC casing and capping medium grade of suitable size run on wall/surface with all fittings (ISI Marked) controlled by one switch including CI/MS/ wooden sunk box of required size, & as directed by Engr in Charge & 3mm thick plastic laminated sheet, including cutting chases to wall making good the disturbed surfaces to match with the existing specification complete all as specified.

All as per srl item No-109 here in above but for One 3 pin socket outlet, 5 Amps, independent, with cables 1.5 sq. mm size

All as per srl item No-109 here in above but for One 3 pin socket outlet, 5 Amps on the same board with other switches, with cables 1.5 sq. mm size

All as per srl item No-109 here in above but for One 3 pin socket outlet, 15 Amps, independent, with cables 2.5 sq. mm size

supply & fixing switch piano flush type, 05/06 Amps single pole, one way 240 volts complete all as specified &directed

S&F in replacement Switch socket combination 2 in 1, 3 pin, 6 Amp flush type universal complete all as specifeid and directed.

M&L for switch socket combination out let, 6 pin 5and 15 amps multi purpose 2 in 1 flush type, 230 volts.

S & F Modular Switch one way 6 A, 1 module complete all as per specified and directed.

S & F Modular Switch one way 16 A, 1 module complete all as per specified and directed.

S & F Modular Socket,6A - 2/3 pin combined 2 module complete all as per specified and directed.

S & F Modular Socket,6A16A - 2/3 pin combined 2 module complete all asper specified and directed.

S & F in repair Modular white cover plate with frame, 3 module complete all as per specified and directed.

S & F in repair Modular white cover plate with frame, 4 module complete all as per specified and directed.

S & F in repair Modular white cover plate with frame, 6 module complete all as per specified and directed.

S & F in repair Modular white cover plate with frame, 8 module complete all as per specified and directed.

Supply & fixing of ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

S&F decorative ultra slim linear LED 20 Watt 4' long lighting fixture with extruded al heat sink, environment friendly, energy efficient ready to use pack including LED tube complete with inbuilt electronic driver, PCB, connector block etc. including connecting up three copper flexible cable from ceiling rose to fittings including connecting up and fixed on including two nos PVC square box of required size complete all as specified & directed.

Supply & fixing lamp holder (Angular / Straight), insulated body, with back plate for batten fitting all as specified and directed by Engr-in-Charge

Supply and fixing LED lamp 9 W all as specified and directed by Egnr-in-Charge.

Supply and Fixing Fan step regulator, 120W - 2 module type electronic fan regulator, duly ISI marked with and including connector complete all as specified & directed.

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and Fixing exhaust fan 300 mm sweep PVC body with louver, 240 volts AC single phase, 50 Hz, ISI marked, including necessary work in wall/sheet, including connection cable, nut bolt and other fixing material complete all as specified and directed by Engr-in-Charge.

Supply & Fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge.

Supply and fixing sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 4 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in - Charge.

Supply and fixing MCB, SP, AC, 240 volts "B" series capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

Supply & fixing MCB, SPN (single pole neutral), AC, 240 volts, B series capacity 32 Amps 10kA and making connections complete all as specified & directed.

Supply and fixing electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc

Supplying and fixing 1100volts grade heavy duty cablPVC insulated aluminiumc onductor, served with innersheathing of PVC tape andoverall PVC sheathed in service connections suspen-ded by insulating hangers notmore than 1 metre apart including4mm suspensionwire, one twin core cable flat or circular 10 sq mm

M/S STARE BUILDERS

JANDOO AND CO

BHAT CONSTRUCTIONS AND BUILFERS

M/S GEE EMM MIR