Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Ref. No.
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
Refer Docs
EMD Value
₹86.2 L
Closing Date
13 Sept 2022, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Manager
Power Grid Corporation of India Limited, Saudamini, 3rd Floor, Plot No 2, Sector 29 Gurugram (Haryana) 122001
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
5002002317/OTHERS/DOM/A06-CC CS -7
Open
Civil Works - Buildings
Works
Manesar
₹25,000
₹86.2 L
13 Sept 2022
30 Jun 2022
15 Sept 2022
30 Jun 2022
13 Sept 2022
30 Jun 2022
11 Jul 2022
Package Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
Package Code DC1
Specification No. 5002002317/OTHERS/DOM/A06-CC CS -7
5002002317/OTHERS/DOM/A06-CC CS -7
1 Fill up only green shaded cells in Sch-1 and Bid Form 2nd Envelope.
2 All the cells in Sch-2 and Sch-3 are auto filled, therefore no cell is required to be filled up there.
3 Instructions / error messages, if any, will be displayed automatically after selecting the cell.
4 After filling up all the schedues, save the file, take print out of all the schedules and Bid form and sign & stamp and submit them as hard copy of the 2nd envelope (Price part) of the bid. Also ensure to submit the soft copy of the the same file on CD/ DVD.
पावर ग्रिड कारपोरेशन ऑफ इण्डिया लिमिटेड
(भारत सरकार का उद्यम)
Power Grid Corporation of India Limited
(A Government of India Enterprises)
I While filling up the worksheets following may please be observed :
(i) Fill up only green shaded cells.
(ii) Certain data type entries have been restricted, such as Numeric values or limits of numeric values.
(iii) Select only the options provided in pull down menus.
(iv) Do not link any cell of this work book with any other work book.
(v) Do not use copy & paste or cut & paste options for filling up the data.
(vi) Do not reformat any of the cell of the work book.
II This Workbook consists of following worksheets :
Opening page of the workbook.
Names of Bidder :
● Select Sole Bidder or JV (Joint Venture) from the pull down menu. Do not leave this cell blank.
● Select nos. of the JV Partners other than the Lead Partner from drop down menu.
● In case of JV partners more than 2, enter details of 3rd & more partners along with details of 2nd partner.
● Fill up names and address of the Sole Bidder and /or Joint Venture.
● Fill up date in dd-mm-yyyy format from drop down menu.
● Click for Sch-1 given at the right top of the worksheet to go to Sch-1.
Sch-1 (Price Components (Price Break-up) ) :
● Fill up unit rates for all the items in numeric values greater than 0 (zero). If unit rate is left blank, the corresponding item shall be deemed to be included in the total price.
● Total amount shall get calculated automatically.
Sch -2(Taxes and Duties) :
● Taxes and duties shall be displayed automatically.
● No cell is required to be filled in by the bidder in this worksheet.
Sch -3(Grand Summary) :
● Summary of the Schedule-1 without considering discount (mentioned in the work sheet discount) shall be displayed automatically.
● No cell is required to be filled in by the bidder in this worksheet.
Bid form 2nd Envelope :
● Fill up ref. no. as bidder's ref no. of this letter.
● This letter shall consider the net price as per Sch-3 (After Discount).
● Fill up names & Designation of the representatives of other JV partner(s) if the bidder is JV (Joint Venture) .
● Fill up additional information as required.
Happy Bidding !
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
5002002317/OTHERS/DOM/A06-CC CS -7 Sole Bidder 1
Enter following details of the bidder
Specify type of Bidder [Select from drop down menu] Sole Bidder 0
Name of Sole Bidder
Address of Sole Bidder
Name of other Partner - 1
Address of other Partner - 1
Name of other Partner - 2 (more, if any)
Address of other Partner - 2 (more, if any)
5002002317/OTHERS/DOM/A06-CC CS -7 Schedule - 1 Direct Total #REF! Sole Bidder `
BO Total #REF! 0
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
(SCHEDULE OF RATES AND PRICES)
Bidder’s Name and Address (Sole Bidder) : To:
Contract Services
Name : Power Grid Corporation of India Ltd., , &
Address : "Saudamini", Plot No.-2
Gurgaon (Haryana) - 122001
Price Components (Price Break-up) Direct
All Prices are in Indian Rupees.
SI. No. PR No PR Line Item No Activity Header PR Activity No Activity Description Service code SAC (Service Accounting Codes) Whether SAC in column '8’ is confirmed. If not indicate applicable the SAC # Rate of GST applicable ( in %) Whether rate of GST in column ‘ 10 ’ is confirmed. If not indicate applicable rate of GST # Description Unit Qty Unit Rate Total Price
I Construction of Data Centre Building at Manesar
1 7000018796 10 10 10 1. EARTH WORK 120000345 995433 18 2.6.1 earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m inwidth as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m,disposed earth to belevelled and neatly dressed. / All kinds of soil M3 15439.67 Included 0.00 0.00 0 0 0.00
2 7000018796 10 10 20 1. EARTH WORK 120000392 995433 18 2.26.1 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. /All kinds ofsoil. M3 24008.24 Included 0.00 0.00 0 0 0.00
3 7000018796 10 10 30 1. EARTH WORK 120000391 995433 18 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cmin depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. M3 5582.80 Included 0.00 0.00 0 0 0.00
CEMENT CONCRETE WORK
4 7000018796 20 20 10 2. CEMENT CONCRETE WORK 120000438 995454 18 4.1.4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All workup to plinth level : / 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size). M3 15.00 Included 0.00 0.00 0 0 0.00
5 7000018796 20 20 20 2. CEMENT CONCRETE WORK 120000440 995454 18 4.1.6 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All workup to plinth level : / 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size). M3 25.00 Included 0.00 0.00 0 0 0.00
6 7000018796 20 20 30 2. CEMENT CONCRETE WORK 120000442 995454 18 4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All workup to plinth level : / 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size). M3 500.71 Included 0.00 0.00 0 0 0.00
7 7000018796 20 20 40 2. CEMENT CONCRETE WORK 120000472 995454 18 4.12 Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as permanufacturer’s specifications. The rate will be per 50kg of cement/bag of cement) B50 1302.73 Included 0.00 0.00 0 0 0.00
8 7000018796 20 20 50 2. CEMENT CONCRETE WORK 120000477 995454 18 4.17 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominalsize) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand includingfinishing the top smooth M2 128.93 Included 0.00 0.00 0 0 0.00
REINFORCED CEMENT CONCRETE WORK
9 7000018796 30 30 10 3. REINFORCED CEMENT CONCRETE WORK 120000499 995457 18 5.9.1 Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns,etc. for mass concrete. M2 723.05 Included 0.00 0.00 0 0 0.00
10 7000018796 30 30 20 3. REINFORCED CEMENT CONCRETE WORK 120000500 995457 18 5.9.2 Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attachedpilasters, butteresses, plinth and string courses etc. M2 2283.56 Included 0.00 0.00 0 0 0.00
11 7000018796 30 30 30 3. REINFORCED CEMENT CONCRETE WORK 120000501 995457 18 5.9.3 Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings,balconies and access platform. M2 12353.98 Included 0.00 0.00 0 0 0.00
12 7000018796 30 30 40 3. REINFORCED CEMENT CONCRETE WORK 120000502 995457 18 5.9.4 Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) M2 11.31 Included 0.00 0.00 0 0 0.00
13 7000018796 30 30 50 3. REINFORCED CEMENT CONCRETE WORK 120000503 995457 18 5.9.5 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders,bressumers and cantilevers. M2 11406.33 Included 0.00 0.00 0 0 0.00
14 7000018796 30 30 60 3. REINFORCED CEMENT CONCRETE WORK 120000504 995457 18 5.9.6 Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Postsand Struts. M2 4421.60 Included 0.00 0.00 0 0 0.00
15 7000018796 30 30 70 3. REINFORCED CEMENT CONCRETE WORK 120000505 995457 18 5.9.7 Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) exceptspiral-staircases. M2 278.23 Included 0.00 0.00 0 0 0.00
16 7000018796 30 30 80 3. REINFORCED CEMENT CONCRETE WORK 120000518 995457 18 5.9.19 Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc.,including edges. M2 75.90 Included 0.00 0.00 0 0 0.00
17 7000018796 30 30 90 3. REINFORCED CEMENT CONCRETE WORK 120000525 995454 18 5.11.1 Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including costof de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Planarea to be measured) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). M2 12262.73 Included 0.00 0.00 0 0 0.00
18 7000018796 30 30 100 3. REINFORCED CEMENT CONCRETE WORK 120003380 995421 18 5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concretework; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures inrecommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability andworkability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payableseparately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shallhave discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 gradewith minimum cement content of 330 kg /cum" M3 85.93 Included 0.00 0.00 0 0 0.00
19 7000018796 30 30 110 3. REINFORCED CEMENT CONCRETE WORK 120003381 995421 18 5.33.1.2 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concretework; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability andworkability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payableseparately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shallhave discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M30 gradewith minimum cement content of 350 kg /cum" M3 6718.60 Included 0.00 0.00 0 0 0.00
20 7000018796 30 30 120 3. REINFORCED CEMENT CONCRETE WORK 120003382 995421 18 5.33.2.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concretework; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures inrecommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability andworkability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payableseparately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shallhave discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level up to floor V level.Concrete of M25 grade with minimum cement content of 330 kg /cum" M3 36.04 Included 0.00 0.00 0 0 0.00
21 7000018796 30 30 130 3. REINFORCED CEMENT CONCRETE WORK 120003383 995421 18 5.33.2.2 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concretework; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability andworkability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payableseparately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shallhave discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level up to floor V level.Concrete of M30 grade with minimum cement content of 350 kg /cum" M3 5080.09 Included 0.00 0.00 0 0 0.00
22 7000018796 30 30 140 3. REINFORCED CEMENT CONCRETE WORK 120000568 995454 18 5.35 Add for using extra cement in the items of design mix over and above the specified cement content therein. QTL 4172.23 Included 0.00 0.00 0 0 0.00
23 7000018796 30 30 150 3. REINFORCED CEMENT CONCRETE WORK 120002953 995454 18 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all completeup to plinth level. Thermo-Mechanically Treated bars. MT 612408.08 Included 0.00 0.00 0 0 0.00
24 7000018796 30 30 160 3. REINFORCED CEMENT CONCRETE WORK 120000549 995454 18 5.22A.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all completeabove plinth level. Thermo-Mechanically Treated bars. KG 767418.75 Included 0.00 0.00 0 0 0.00
25 7000018796 30 30 170 3. REINFORCED CEMENT CONCRETE WORK 120000572 995454 18 5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each fourfloors or part thereof. M3 1222.72 Included 0.00 0.00 0 0 0.00
26 7000018796 40 40 10 4. BRICK WORK 120000601 995456 18 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cementmortar 1:6 (1 cement : 6 coarse sand) M3 265.00 Included 0.00 0.00 0 0 0.00
27 7000018796 40 40 20 4. BRICK WORK 120000607 995456 18 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level upto floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) M3 1169.13 Included 0.00 0.00 0 0 0.00
28 7000018796 40 40 30 4. BRICK WORK 120000608 995456 18 6.5 Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level for each four floors or partthereof by mechanical means. M3 465.45 Included 0.00 0.00 0 0 0.00
29 7000018796 40 40 40 4. BRICK WORK 120000616 995456 18 6.12.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in.Cement mortar 1:4 (1 cement : 4 coarse sand) M2 21.84 Included 0.00 0.00 0 0 0.00
30 7000018796 40 40 50 4. BRICK WORK 120000618 995456 18 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinthlevel up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand) M2 1160.07 Included 0.00 0.00 0 0 0.00
31 7000018796 40 40 60 4. BRICK WORK 120000619 995456 18 6.14 Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means. M2 383.53 Included 0.00 0.00 0 0 0.00
32 7000018796 40 40 70 4. BRICK WORK 120000620 995456 18 6.15 Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry. M2 1181.92 Included 0.00 0.00 0 0 0.00
33 7000018796 40 40 80 4. BRICK WORK 120003384 995421 18 6.47 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure aboveplinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesivemortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made forseperately). M3 1044.79 Included 0.00 0.00 0 0 0.00
34 7000018796 40 40 90 4. BRICK WORK 120003385 995421 18 26.49.3 Providing and fixing in position factory made EPS cement sandwich wall/roof/floor light weight solid core panels made ofcore material of EPS granule balls/beads (conforming to IS 4671:1984 and shall have density not less than 15kg per cum) adhesive,cement, sand, flyash and other bonding material in mortar state processed to form in a preset mould. The outer face on both sides ofthe panels will be non asbestos fiber cement board confirming to IS 14862:2000 or Calcium silicate board confirming to EN 14306:2009of 5mm thick each. Panel shall be laid on 6mm thick cement mortar (1 cement: 2 fine sand) mixed with chemical adhesive of 0.5kg per50kg of cement or shall be preferably fixed into 'C' channel made of 1.2mm thick MS plate screwed/fastenened to the slab/column/beametc. The panel shall fixed vertically with tongue and groove joint and horizontally locked with steel bar between each other andfloors and filled with cement mortar and adhesive. Panels should be used as floor & roofing with additional structural support,steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturersspecifications and under the overall direction of Engineer-in-Charge (Cost of all the material is included except ""C channel""which will be paid seperately). Non load bearing panels 75mm thick of required size" M2 118.19 Included 0.00 0.00 0 0 0.00
35 7000018796 40 40 110 4. BRICK WORK 120003386 995421 18 26.49.5 Providing and fixing in position factory made EPS cement sandwich wall/roof/floor light weight solid core panels made ofcore material of EPS granule balls/beads (conforming to IS 4671:1984 and shall have density not less than 15kg per cum) adhesive,cement, sand, flyash and other bonding material in mortar state processed to form in a preset mould. The outer face on both sides ofthe panels will be non asbestos fiber cement board confirming to IS 14862:2000 or Calcium silicate board confirming to EN 14306:2009of 5mm thick each. Panel shall be laid on 6mm thick cement mortar (1 cement: 2 fine sand) mixed with chemical adhesive of 0.5kg per50kg of cement or shall be preferably fixed into 'C' channel made of 1.2mm thick MS plate screwed/fastenened to the slab/column/beametc. The panel shall fixed vertically with tongue and groove joint and horizontally locked with steel bar between each other andfloors and filled with cement mortar and adhesive. Panels should be used as floor & roofing with additional structural support,steel or RCC depending upon the design. All the operation shall be completed in all respect as per drawings, Manufacturersspecifications and under the overall direction of Engineer-in-Charge (Cost of all the material is included except ""C channel""which will be paid seperately). Non load bearing panels 100mm thick of required size" M2 580.75 Included 0.00 0.00 0 0 0.00
MARBLE & GRANITE WORK
36 7000018796 50 50 10 5. MARBLE & GRANITE WORK 120000739 995474 18 8.2.2.2 Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms,vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mmthick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touchups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite ofany colour and shade. Area of slab over 0.50 sqm. M2 26.23 Included 0.00 0.00 0 0 0.00
37 7000018796 50 50 20 5. MARBLE & GRANITE WORK 120000743 995474 18 8.5 Extra for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters andsimilar location in marble / Granite / stone work, including necessary holes for pillar taps etc. including moulding, rubbing andpolishing of cut edges etc. complete. EA 11.00 Included 0.00 0.00 0 0 0.00
38 7000018796 50 50 30 5. MARBLE & GRANITE WORK 120003387 995421 18 8.10.2 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixedin urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy groutor with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction ofEngineer-in-charge and finished smooth. Granite Stone of approved shade" M2 5.16 Included 0.00 0.00 0 0 0.00
WOOD WORK, DOORS AND WINDOWS
39 7000018796 60 60 10 6. WOOD WORK 120000756 995476 18 9.1.1. Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in positionwith hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).Second class teak wood M3 0.96 Included 0.00 0.00 0 0 0.00
40 7000018796 60 60 20 6. WOOD WORK 120000785 995476 18 9.7.7.2 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows andclerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling forpanelled or panelled and glazed shutters 25 mm to40 mm thick (Float glass panes ) : 5.5 mm thick glass panes M2 3.29 Included 0.00 0.00 0 0 0.00
41 7000018796 60 60 30 6. WOOD WORK 120000808 995476 18 9.20.1 Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block boardconstruction with frame of 1stclass hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and faceveneers on both faces of shutters. : 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. M2 65.76 Included 0.00 0.00 0 0 0.00
42 7000018796 60 60 40 6. WOOD WORK 120000815 995476 18 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over allarea of door shutter to be measured). M2 65.76 Included 0.00 0.00 0 0 0.00
43 7000018796 60 60 50 6. WOOD WORK 120000816 995476 18 9.24.1 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area ofdoor shutter to be measured) : Rectangular or square. M2 65.76 Included 0.00 0.00 0 0 0.00
44 7000018796 60 60 60 6. WOOD WORK 120000873 995476 18 9.53 Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs andembedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) EA 240.00 Included 0.00 0.00 0 0 0.00
45 7000018796 60 60 70 6. WOOD WORK 120000925 995476 18 9.71.2 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :100x60x2.50 mm EA 84.00 Included 0.00 0.00 0 0 0.00
46 7000018796 60 60 80 6. WOOD WORK 120000956 995476 18 9.83 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS :3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm) with necessary accessories and screws etc. complete. EA 57.00 Included 0.00 0.00 0 0 0.00
47 7000018796 60 60 90 6. WOOD WORK 120000987 995476 18 9.96.1 Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 300x16 mm EA 19.00 Included 0.00 0.00 0 0 0.00
48 7000018796 60 60 100 6. WOOD WORK 120000989 995476 18 9.97.1 Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 )transparent or dyed to required colour or shade with necessary screws etc. complete : 300x10 mm EA 114.00 Included 0.00 0.00 0 0 0.00
49 7000018796 60 60 110 6. WOOD WORK 120000994 995476 18 9.98 Providing and fixing aluminium pull bolt lock anodised ISI marked (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour and shade with necessary screws bolts, nut and washers etc. complete. EA 16.00 Included 0.00 0.00 0 0 0.00
50 7000018796 60 60 120 6. WOOD WORK 120000996 995476 18 9.100.1 Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868)transparent or dyed to required colour or shade with necessary screws etc. complete : 125 mm EA 114.00 Included 0.00 0.00 0 0 0.00
51 7000018796 60 60 130 6. WOOD WORK 120000999 995476 18 9.101.1 Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 asper IS : 1868)transparent or dyed to required colour and shade with necessary screws etc. complete. : Single rubber stopper EA 41.00 Included 0.00 0.00 0 0 0.00
52 7000018796 60 60 140 6. WOOD WORK 120001018 995476 18 9.113 Providing and fixing bright finished 100mm mortice lock with 6 levers without pair of handles for aluminium door withnecessary screws etc complete (Best make of approved quality) as per direction of Engineer-in-charge. EA 25.00 Included 0.00 0.00 0 0 0.00
53 7000018796 60 60 150 6. WOOD WORK 120001041 995476 18 9.127.2 Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with highdensity protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type Including cost ofadhesive of approved quality : 1.0 mm thick. M2 131.52 Included 0.00 0.00 0 0 0.00
54 7000018796 60 60 160 6. WOOD WORK 120001065 995476 18 9.136 Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I.sheet(zinc coating not less than 120gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting60 minutes fire rateddoor shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dashfastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per directionof Engineer-in-charge(Dash fastener to be paid for separately). M 150.35 Included 0.00 0.00 0 0 0.00
55 7000018796 60 60 170 6. WOOD WORK 120001066 995476 18 9.137 Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II)tested and certified as per laboratory approved by Engineer-in-charge with suitable mounting on doorframe, consisting of verticalstyles, lock rail, top rail 100mm wide, bottom rail200mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/sqmduly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, includingapplying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in charge(pannelling to be paid forseparately). M2 84.36 Included 0.00 0.00 0 0 0.00
56 7000018796 60 60 180 6. WOOD WORK 120003388 995421 18 9.138 Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity &radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification offire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABLaccredited lab or by any other accreditation body which operates in accordace with ISO/IEC 17011 and accredits labs as per ISO/IEC17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or2.42 sqm." M2 21.09 Included 0.00 0.00 0 0 0.00
57 7000018796 60 60 190 6. WOOD WORK 120001068 995476 18 9.139 Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the PanicLatch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete. EA 24.00 Included 0.00 0.00 0 0 0.00
58 7000018796 60 60 200 6. WOOD WORK 120003389 995421 18 9.147a.6 Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVCmulti-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanizedmild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazingbeads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated)casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessarystainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required)shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gapbetween frame and adjacent finished wall shall be filled with weather roof silicon sealant over backer rod of required size and ofapproved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and siliconsealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on thisaccount M2 7.50 Included 0.00 0.00 0 0 0.00
59 7000018796 60 60 210 6. WOOD WORK 120003390 995421 18 9.147b.1 Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chamberedframe and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2mm thick galvanized mild steel sectionmade from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads ofappropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic capsand necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (ifrequired) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixingframe the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod ofrequired size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / doubleglass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but noextra payment on this account shall be made.. Note: For uPVC frame, sash and mullion extruded profiles minus 5% toleranceindimension i.e. in depth & width of profile shall be acceptable. Fixed window / ventilator made of (small series) frame 47 x 50 mm &mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75sqm.) M2 139.00 Included 0.00 0.00 0 0 0.00
60 7000018796 60 60 220 6. WOOD WORK 120003391 995421 18 26.86.6 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & otherFrames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (woodpowder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints afterapplying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum,screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof andfire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per directionof Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/windowframes, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions onplus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 125 mm RM 121.50 Included 0.00 0.00 0 0 0.00
61 7000018796 60 60 230 6. WOOD WORK 120003392 995421 18 26.88.1 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter ofrequired size comprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum andscrew withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 andresistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fireretardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on bothfaces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed countersunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall bepaid separately) 30 mm thick M2 38.16 Included 0.00 0.00 0 0 0.00
62 7000018796 70 70 10 7. STEEL WORK 120001115 995476 18 10.1 Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in positionand applying a priming coat of approved steel primer all complete. KG 6989.40 Included 0.00 0.00 0 0 0.00
63 7000018796 70 70 20 7. STEEL WORK 120001121 995476 18 10.6.1 Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through theirentire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides andarrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixingnecessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -part 1and M.S. top cover of required thickness for rolling shutters. : 80x1.25mm M.S. laths with 1.25 mm thick top cover. M2 75.72 Included 0.00 0.00 0 0 0.00
64 7000018796 70 70 30 7. STEEL WORK 120001124 995476 18 10.7 Providing and fixing ball bearing for rolling shutters. EA 6.00 Included 0.00 0.00 0 0 0.00
65 7000018796 70 70 40 7. STEEL WORK 120001125 995476 18 10.8.1 Extra for providing mechanical device chain and crank operation for operating rolling shutters. : Exceeding 10.00 sqm andupto 16.80 sqm in the area. M2 32.04 Included 0.00 0.00 0 0 0.00
66 7000018796 70 70 50 7. STEEL WORK 120001126 995476 18 10.8.2 Extra for providing mechanical device chain and crank operation for operating rolling shutters. : Exceeding 16.80 sqm inarea. M2 18.96 Included 0.00 0.00 0 0 0.00
67 7000018796 70 70 60 7. STEEL WORK 120001127 995476 18 10.9 Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved byEngineer-in- charge, (area of grill to be measured). M2 14.20 Included 0.00 0.00 0 0 0.00
68 7000018796 70 70 70 7. STEEL WORK 120001153 995476 18 10.25.2 Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a primingcoat of approved steel primer using structural steel etc. as required. : In gratings, frames, guard bar, ladder, railings,brackets, gates and similar works. KG 2970.00 Included 0.00 0.00 0 0 0.00
69 7000018796 70 70 80 7. STEEL WORK 120001157 995476 18 10.27.1 Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8grade (yield strength 480 N/mm 2 ), counter sunk head, comprising of 10 m dia polyamide P A 6 grade sleeve, including drilling ofhole in frame , concrete/ masonry , etc. as per direction of Engineer-in-charge : 10 x60 mm EA 339.00 Included 0.00 0.00 0 0 0.00
70 7000018796 70 70 90 7. STEEL WORK 120001162 995476 18 10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc. including welding,grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts andbolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., ofrequired size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge.(for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts,fasteners etc.) KG 3583.23 Included 0.00 0.00 0 0 0.00
71 7000018796 70 70 100 7. STEEL WORK 120002687 995424 18 19.15.1 Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarsesand : 6 graded stone aggregate 20 mm nominal size) as per standard design : With 20x20 mm square bar EA 56.00 Included 0.00 0.00 0 0 0.00
72 7000018796 70 70 110 7. STEEL WORK 120002700 995424 18 19.19.3.1 Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality (H D - 20): Circular shape 560 mm internal diameter EA 8.00 Included 0.00 0.00 0 0 0.00
73 7000018796 80 80 10 8. FLOORING WORK 120001170 995474 18 11.3.1 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neatcement including cement slurry, but excluding the cost of nosing of steps etc. complete. : 40mm thick with 20mm nominal size stoneaggregate. M2 633.01 Included 0.00 0.00 0 0 0.00
74 7000018796 80 80 20 8. FLOORING WORK 120001231 995474 18 11.26.1 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigmentto match the shade of the slab including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand):25 mm thick. M2 999.54 Included 0.00 0.00 0 0 0.00
75 7000018796 80 80 30 8. FLOORING WORK 120001232 995474 18 11.27 Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1cement 3coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing andpolishing complete. M2 40.25 Included 0.00 0.00 0 0 0.00
76 7000018796 80 80 40 8. FLOORING WORK 120001241 995474 18 11.33.1 25mm wooden planking, tongued and grooved in flooring including fixing with iron screws complete with : Second class teakwood M2 66.59 Included 0.00 0.00 0 0 0.00
77 7000018796 80 80 50 8. FLOORING WORK 120001246 995474 18 11.37 Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1st qualityconforming to IS :15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar1:4 (1 Cement : 4Coarse sand) including pointing the joints with white cement and matching pigment etc., complete. M2 264.32 Included 0.00 0.00 0 0 0.00
78 7000018796 80 80 60 8. FLOORING WORK 120003230 995474 18 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer),of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, inskirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with greycement slurry @ 3.3kg per sqm,including pointing in white cement mixed with pigment of matching shade complete. M2 724.80 Included 0.00 0.00 0 0 0.00
79 7000018796 80 80 70 8. FLOORING WORK 120003393 995421 18 11.41A.1.1 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) withwater absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints withwhite cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will bedone with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tilesgently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 600 mm M2 2398.33 Included 0.00 0.00 0 0 0.00
80 7000018796 80 80 80 8. FLOORING WORK 120003394 995421 18 11.41A.1.3 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) withwater absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints withwhite cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will bedone with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tilesgently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 1200 mm M2 392.40 Included 0.00 0.00 0 0 0.00
81 7000018796 80 80 90 8. FLOORING WORK 120003395 995421 18 11.41A.3.1 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) withwater absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints withwhite cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will bedone with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tilesgently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm M2 416.62 Included 0.00 0.00 0 0 0.00
82 7000018796 80 80 100 8. FLOORING WORK 120003396 995421 18 11.55.1 Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinearportions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick baseof cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixedwith pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by theEngineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. M2 639.20 Included 0.00 0.00 0 0 0.00
83 7000018796 80 80 110 8. FLOORING WORK 120003270 995474 18 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions ofthe building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cementmortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigmentof matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by theEngineer-in-Charge.Polished Granite stone slab jet Black, Cherry Red, Elite Brown,Cat Eye or equivalent. M2 613.65 Included 0.00 0.00 0 0 0.00
84 7000018796 80 80 120 8. FLOORING WORK 120001865 995428 18 16.90 Providing and laying tactile tile (for vision impaired persons as per standards) of size 300x300x9.8mm having with waterabsorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such asfootpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in allshapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction ofEngineer-in-Charge. M2 66.55 Included 0.00 0.00 0 0 0.00
ROOFING & FALSE CEILING
85 7000018796 90 90 10 9. ROOFING & FALSE CEILING 120001318 995453 18 12.21.1 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge),including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase M 229.87 Included 0.00 0.00 0 0 0.00
86 7000018796 90 90 20 9. ROOFING & FALSE CEILING 120001319 995453 18 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate of 20 mm nominal size) over P.V.C. sheet1mx1mx400micron, finished with 12mm cement plaster 1:3 (1 cement :3 coarsesand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. EA 19.00 Included 0.00 0.00 0 0 0.00
87 7000018796 90 90 30 9. ROOFING & FALSE CEILING 120001369 995453 18 12.45.3 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections,power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consistingof angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed tothe ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of25x10x0.50 mm of required length with nuts &bolts of required size and other end of angle hanger fixed with intermediate G.I.channels 45x15x0.9 mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mmwith tapered flanges of 26 mm each having lips of10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular toG.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixingperimeter channels 0.5 mm thick 27 mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partitionwith the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board toceiling section and perimeter channel with the help of dry wall screws of size3.5 x 25 mm at 230 mm c/c, including jointing andfinishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishingwith jointing compound in 3layers covering upto 150 mm or both sides of joint and two coats of primer suitable for board, all as permanufacture's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made withframe of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge butexcluding the cost of painting with : 12.5 mm thick tapered edge gypsum moisture resistant board. M2 760.68 Included 0.00 0.00 0 0 0.00
88 7000018796 90 90 40 9. ROOFING & FALSE CEILING 120001384 995453 18 12.52.2 Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level suspended oninter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120gsm/sqm, both side inclusive) consisting of main"T" runner with suitably spaced joints to get required length and of size 24x38mmmade from 0.30mm thick (minimum) sheet, spaced at1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick(minimum) sheet, 1200mm long spaced between main "T" at600mmcenter to center to form a grid of 1200x600 mm and secondary cross T of length 600mm and size 24x25mm made of 0.30 mmthick(minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening forservices like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling usingGI slotted cleats of size 27 x 37 x 25 x1.6x mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners,4mm GI adjustablerods with galvanised butterfly level clips of size 85 x30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposedwidth of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specificationsdrawings and as directed by Engineer-in-charge.: GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size595x595 mm and 0.5mm thick with 8mmdrop; made of GI sheet having galvanizing of 100 gms/sqm(both sides inclusive) and 20%perforation area with 1.8mmdia holes and having NRC (Noise Reduction Coefficient ) of0.5, electro statically polyester powder coatedof thickness60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiberacoustical fleece. M2 1722.55 Included 0.00 0.00 0 0 0.00
89 7000018796 90 90 50 9. ROOFING & FALSE CEILING 120001390 995453 18 12.55 Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solarreflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortarin the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1,including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along theparapet walls in the same manner M2 1429.56 Included 0.00 0.00 0 0 0.00
FINISHING WORKS
90 7000018796 100 100 10 10. FINISHING WORKS 120001400 995472 18 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand) M2 19678.68 Included 0.00 0.00 0 0 0.00
91 7000018796 100 100 20 10. FINISHING WORKS 120001418 995472 18 13.11 18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement: 5 coarse sand) finished with a toplayer 6mm thick cement plaster 1:6 (1 cement: 6 fine sand). M2 3534.12 Included 0.00 0.00 0 0 0.00
92 7000018796 100 100 30 10. FINISHING WORKS 120001423 995472 18 13.16.1 6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand) M2 1774.04 Included 0.00 0.00 0 0 0.00
93 7000018796 100 100 40 10. FINISHING WORKS 120001463 995473 18 13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnablecement primer. M2 11182.96 Included 0.00 0.00 0 0 0.00
94 7000018796 100 100 50 10. FINISHING WORKS 120001471 995473 18 13.50.1 Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and softwood) M2 30.24 Included 0.00 0.00 0 0 0.00
95 7000018796 100 100 60 10. FINISHING WORKS 120003200 995473 18 13.48A.1 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with siliconadditives. 13.48A.1 New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primerapplied @ 0.90 litre/10 sqm. M2 1634.43 Included 0.00 0.00 0 0 0.00
96 7000018796 100 100 70 10. FINISHING WORKS 120001477 995473 18 13.52.1 Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specificationsincluding appropriate priming coat, preparation of surface, etc. complete. : On steel work M2 198.00 Included 0.00 0.00 0 0 0.00
97 7000018796 100 100 80 10. FINISHING WORKS 120001487 995473 18 13.58 Providing and applying two coats of fire retardant paint on cleaned wood/ply surface @ 3.5 sqm per litre per coat includingpreparation of base surface as per recommendations of manufacturer to make the surface fire retardant. M2 207.96 Included 0.00 0.00 0 0 0.00
98 7000018796 100 100 90 10. FINISHING WORKS 120001489 995473 18 13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on newwork. M2 2375.80 Included 0.00 0.00 0 0 0.00
99 7000018796 100 100 100 10. FINISHING WORKS 120001490 995473 18 13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on newwork. M2 531.15 Included 0.00 0.00 0 0 0.00
100 7000018796 100 100 110 10. FINISHING WORKS 120001511 995472 18 13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over theplastered wall surface to prepare the surface even and smooth complete. M2 11182.96 Included 0.00 0.00 0 0 0.00
101 7000018796 100 100 120 10. FINISHING WORKS 120001517 995473 18 13.83.2 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content lessthan 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shadeand colour. : Two coats. M2 9567.84 Included 0.00 0.00 0 0 0.00
102 7000018796 100 100 130 10. FINISHING WORKS 120003397 995421 18 13.114 Melamine polishing on wood work (one or more coat). M2 161.76 Included 0.00 0.00 0 0 0.00
103 7000018796 110 110 10 11. ROAD WORKS 120001732 995428 18 16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to anaverage of 22.5 cm. depth, dressing to camber and consolidating with road roller including making good the undulations etc. andre-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. M2 1366.85 Included 0.00 0.00 0 0 0.00
104 7000018796 110 110 20 11. ROAD WORKS 120001832 995421 18 16.62 Providing and applying 2.5mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplasticmaterial by fully/ semiautomatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propanetank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P,cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-chargeand accordance with applicable specifications. M2 50.00 Included 0.00 0.00 0 0 0.00
105 7000018796 110 110 30 11. ROAD WORKS 120001809 995421 18 16.49 Making bell mouth opening/ entrance of size 100x50x50cm for drainage pipe under footpath including providing cement concrete1:3:6 (1 cement : 3coarse sand : 6 graded stone aggregate 20mm nominal size) for shape of bell mouth including plastering providingand fixing precast R.C.C./ S.F.R.C. slab including plastering with cement mortar 1:3 (1 cement : 3 fine sand) of 6mm thickness onexposed surface of the slab & bell mouth including centring, shuttering & neat cement punning inside the bell mouth etc. allcomplete. EA 20.00 Included 0.00 0.00 0 0 0.00
106 7000018796 110 110 40 11. ROAD WORKS 120003410 995421 18 16.59.1 Manufacturing, supplying and fixing retro reflective sign boards made up of 2mm thick aluminium sheet, face to be fullycovered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type- IV of ASTM-D 4956-01 inblue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as perIRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @20 cm c/c to back support frame of M.S. angleiron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to avertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end andincluding making holes in pipes, angles flats, providing &fixing M.S. message plate of required size, steel work to be painted withtwo or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromateyellow primer(vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with twoor more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing,specification and direction of Engineer--in-charge. : Mandatory/ Regulatory sign boards of 900 mm diametre with support length of3750 mm. EA 1.00 Included 0.00 0.00 0 0 0.00
107 7000018796 110 110 50 11. ROAD WORKS 120003411 995421 18 16.59.2 Manufacturing, supplying and fixing retro reflective sign boards made up of 2mm thick aluminium sheet, face to be fullycovered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type- IV of ASTM-D 4956-01 inblue and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as perIRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @20 cm c/c to back support frame of M.S. angleiron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to avertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plate of size 100x100x5 mm at the bottom end andincluding making holes in pipes, angles flats, providing &fixing M.S. message plate of required size, steel work to be painted withtwo or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat of zinc chromateyellow primer(vertical MS-Tee support to be painted in black and white colours).Backside of aluminium sheet to be painted with twoor more coats of epoxy paint over and including appropriate priming coat including all leads and lifts etc. complete as per drawing,specification and direction of Engineer--in-charge. : Cautionary /warning sign boards of equilateral triangular shape having eachside of 900mm with support length of 3650mm. EA 1.00 Included 0.00 0.00 0 0 0.00
108 7000018796 110 110 60 11. ROAD WORKS 120001830 995421 18 16.60.1 Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face tobe fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III ofASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated byapplying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means ofsuitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two verticalrows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on theback side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding of f the corners, loweringdown the structural frame work from the gantry , fixing and erecting the same in position all complete as per drawings,specification and direction of the engineer-in-charge.(S tructural frame work including M.S. plate to be provided sep arately . Rectangular area of the sheet only shall be measured for payment). : Overhead informatory road signage M2 1.00 Included 0.00 0.00 0 0 0.00
109 7000018796 110 110 70 11. ROAD WORKS 120001839 995421 18 16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the requiredline, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves(thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required completeetc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stoneshall be approved by Engineer-in-charge). M3 18.86 Included 0.00 0.00 0 0 0.00
110 7000018796 110 110 80 11. ROAD WORKS 120001848 995428 18 16.75 Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shallbe laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wirebrush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid forseparately).(Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately). M3 205.03 Included 0.00 0.00 0 0 0.00
111 7000018796 110 110 90 11. ROAD WORKS 120001854 995428 18 16.79 Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM)specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper tosite, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub- base / base course on well preparedsurface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as perspecifications and directions of Engineer-in-Charge. M3 410.06 Included 0.00 0.00 0 0 0.00
112 7000018796 110 110 100 11. ROAD WORKS 100005390 995421 18 16.46.1 Providing and laying in position bitumen hot sealing compound for expansion joints etc. -Using grade 'A' sealing compound. M 180.00 Included 0.00 0.00 0 0 0.00
113 7000018796 110 110 110 11. ROAD WORKS 120003280 995428 18 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light trafficparking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour &pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sandbedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as perrequired size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. - 80 mmthick C.C. paver block of M-30 grade with approved color design and pattern. M2 50.00 Included 0.00 0.00 0 0 0.00
114 7000018796 120 120 10 12. ALUMINIUM WORK 120002794 995476 18 21.1.2.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubularsections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fastenersof required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDMrubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete asper architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid forseparately) (For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision forfixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid forseparately)) : Powder coated aluminium (minimum thickness of powder coating 50 micron) KG 1367.88 Included 0.00 0.00 0 0 0.00
115 7000018796 120 120 20 12. ALUMINIUM WORK 120002800 995476 18 21.3.3 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprenegasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beadingshall be paid in basic item): With float glass panes of 8 mm thickness M2 146.50 Included 0.00 0.00 0 0 0.00
116 7000018796 120 120 30 12. ALUMINIUM WORK 120002828 995476 18 21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providingand fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings,all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately). M2 61.44 Included 0.00 0.00 0 0 0.00
117 7000018796 120 120 40 12. ALUMINIUM WORK 120002933 998736 18 25.1 Providing and supplying aluminiumextruded tubular and other aluminiumsections as per the architecturaldrawings and approved shop drawings ,the aluminium quality as per grade 6063T5 or T6 as per BS 1474,including superdurable powder coating of 60-80 micronsconforming to AAMA 2604 of requiredcolour and shade as approved by theEngineer-in-Charge. ( The item includescost of material such as cleats,sleeves, screws etc. necessary forfabrication of extruded aluminium framework. Nothing extra shall be paid onthis account). The weight of aluminiumextruded section shall be taken forpurpose of payment. KG 14556.32 Included 0.00 0.00 0 0 0.00
118 7000018796 120 120 50 12. ALUMINIUM WORK 120002934 998736 18 25.2 Designing, fabricating, testing,protection, installing and fixing inposition semi (grid) unitized system ofstructural glazing (with open joints)for linear as well as curvilinearportions of the building for allheights and all levels, including:(a)Structural analysis & design andpreparation of shop drawings for thespecified design loads conforming to IS875 part III (the system must passedthe proof test at 1.5 times design windpressure without any failure),including functional design of thealuminum sections for fixing glazingpanels of various thicknesses,aluminium cleats, sleeves and spliceplates etc. gaskets, screws, toggles,nuts, bolts, clamps etc., structuraland weather silicone sealants,flashings, fire stop(barrier)-cum-smoke seals, microwavecured EPDM gaskets for water tightness,pressure equalisation & drainage andprotection against fire hazardincluding:(b) Fabricating and supplyingserrated M.S. hot dip galvanised /Aluminium alloy of 6005 T5 brackets ofrequired sizes, sections and profilesetc. to accommodate 3 Dimentionalmovement for achieving perfectverticality and fixing structuralglazing system rigidly to the RCC/masonry/structural steel framework ofbuilding structure using stainlesssteel anchor fasteners/ bolts, nylonseperator to prevent bimetalliccontacts with nuts and washers etc. ofstainless steel grade 316, of therequired capacity and in requirednumbers.(c) Providing and filling, twopart pump filled, structural siliconesealant and one part weather siliconesealant compatible with the structuralsilicone sealant of required bite sizein a clean and controlled factory /work shop environment, including doublesided spacer tape, setting blocks andbacker rod, all of approved grade,brand and manufacture, as per theapproved sealant design, within and allaround the perimeter for holding glass.(d) Providing and fixing in positionflashings of solid aluminium sheet 1 mmthick and of sizes, shapes andprofiles, as required as per the siteconditions, to seal the gap between thebuilding structure and all itsinterfaces with curtain glazing to makeit watertight. (e) Making provision fordrainage of moisture/ water that entersthe curtain glazing system to make itwatertight, by incorporating principlesof pressure equalization, providingsuitable gutter profiles at bottom (ifrequired), making necessary holes ofrequired sizes and of required numbersetc. complete. This item includes costof all inputs of designing, labour forfabricating and installation ofaluminium grid, installation of glazedunits, T&P, scaffolding and otherincidental charges including wastagesetc., enabling temporary structures andservices, cranes or cradles etc. asdescribed above and as specified. Theitem includes the cost of getting allthe structural and functional designincluding shop drawings checked by astructural designer, dully approved byEngineer-in-charge. The item alsoincludes the cost of all mock ups atsite, cost of all samples of theindividual components for testing in anapproved laboratory, field tests on theassembled working structural glazing asspecified, cleaning and protection tillthe handing over of the building foroccupation. In the end, the Contractorshall provide a water tight structuralglazing having all the performancecharacteristics etc. all complete asrequired, as per the Architecturaldrawings, as per item description, asspecified, as per the approved shopdrawings and as directed by theEngineer- in-Charge. M2 1819.540 TC-2022001-02-01-01 000012000421 Y033 STATCOM 25.2 DESIGNING, FABRICATING, TESTING, 0.00 7000018796 00120 Package DC-1_Construction of Building 0120 0000000060 12. ALUMINIUM WORK 120002935 998736 18.00 25.3 Providing, assembling and supplyingvision glass panels (IGUs) comprisingof hermetically-sealed 6-12- 6 mminsulated glass (double glazed) visionpanel units of size and shape asrequired and specified, comprising ofan outer heat strengthened float glass6mm thick, of approved colour and shadewith reflective soft coating on surface#2 of approved colour and shade, aninner Heat strengthned clear floatglass 6mm thick, spacer tube 12mm wide,dessicants, including primary seal andsecondary seal (structural siliconesealant) etc. all complete for therequired performances, as per theArchitectural drawings, as per theapproved shop drawings, as specifiedand as directed by theEngineer-in-Charge. The IGUs shall beassembled in the factory/ workshop ofthe glass processor. (Payment forfixing of IGU Panels in the curtainglazing is included in cost of itemNo.25.2) For payment, only the actualarea of glass on face # 1 of the glasspanels (excluding the areas of thegrooves and weather silicone sealant)provided and fixed in position, shallbe measured in sqm. (i) Coloured tintedfloat glass 6mm thick substrate withreflective soft coating on face # 2, +12mm Airgap + 6mm Heat Strengthenedclear Glass of approved make havingproperties as visible Lighttransmittance (VLT) of 25 to 35 %,Light reflection internal 10 to 15%,light reflection external 10 to 20 %,shading coefficient (0.25- 0.28) and Uvalue of 3.0 to 3.3 W/m2 degree K etc.The properties of performance glassshall be decided by technicalsanctioning authority as per the siterequirement. M2 1819.540 TC-2022001-02-01-01 000012000421 Y033 STATCOM 25.3 P,A&S VISION GLASS PANELS 0.00 7000018796 00120 Package DC-1_Construction of Building 0120 0000000070 12. ALUMINIUM WORK 120003398 995421 18.00 25.4 Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories andhardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4-point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specifiedand as directed by the Engineer- in-Charge. M2 181.950 TC-2022001-02-01-01 000012000421 Y094 Carriage of Material 25.4 VISION GLASS PANELS IGUS 0.00 7000018796 00120 Package DC-1_Construction of Building 0120 0000000080 12. ALUMINIUM WORK 120003399 995421 18.00 8.32 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, withopen grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:(a)Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, properdrainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricatingand supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets(each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon basedfluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant,backer rods etc. (c) The fastening brackets ofAluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement,fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all completerequired to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mockups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembledworking curtain wall with aluminium composite panel cladding, cleaning and protection ofthe curtain wall with aluminium compositepanel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevantaluminium item.sThe Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performancecharacteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shopdrawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external faceof the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimalplaces. M2 1949.520 TC-2022001-02-01-01 000012000421 Y094 Carriage of Material 8.32 ACP CLADDING 0.00 7000018796 00130 Package DC-1_Construction of Building 0130 0000000010 13. WATER PROOFING 120002831 995453 18.00 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen andthe like consisting of : M2 1819.54 Included 0.00 0.00 0 0 0.00
119 7000018796 120 120 60 12. ALUMINIUM WORK 120002935 998736 18 25.3 Providing, assembling and supplyingvision glass panels (IGUs) comprisingof hermetically-sealed 6-12- 6 mminsulated glass (double glazed) visionpanel units of size and shape asrequired and specified, comprising ofan outer heat strengthened float glass6mm thick, of approved colour and shadewith reflective soft coating on surface#2 of approved colour and shade, aninner Heat strengthned clear floatglass 6mm thick, spacer tube 12mm wide,dessicants, including primary seal andsecondary seal (structural siliconesealant) etc. all complete for therequired performances, as per theArchitectural drawings, as per theapproved shop drawings, as specifiedand as directed by theEngineer-in-Charge. The IGUs shall beassembled in the factory/ workshop ofthe glass processor. (Payment forfixing of IGU Panels in the curtainglazing is included in cost of itemNo.25.2) For payment, only the actualarea of glass on face # 1 of the glasspanels (excluding the areas of thegrooves and weather silicone sealant)provided and fixed in position, shallbe measured in sqm. (i) Coloured tintedfloat glass 6mm thick substrate withreflective soft coating on face # 2, +12mm Airgap + 6mm Heat Strengthenedclear Glass of approved make havingproperties as visible Lighttransmittance (VLT) of 25 to 35 %,Light reflection internal 10 to 15%,light reflection external 10 to 20 %,shading coefficient (0.25- 0.28) and Uvalue of 3.0 to 3.3 W/m2 degree K etc.The properties of performance glassshall be decided by technicalsanctioning authority as per the siterequirement. M2 1819.54 Included 0.00 0.00 0 0 0.00
120 7000018796 120 120 70 12. ALUMINIUM WORK 120003398 995421 18 25.4 Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories andhardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4-point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specifiedand as directed by the Engineer- in-Charge. M2 181.95 Included 0.00 0.00 0 0 0.00
121 7000018796 120 120 80 12. ALUMINIUM WORK 120003399 995421 18 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, withopen grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:(a)Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, properdrainage of water to make it watertight including checking of all the structural and functional design.(b) Providing, fabricatingand supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets(each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon basedfluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant,backer rods etc. (c) The fastening brackets ofAluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement,fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all completerequired to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mockups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembledworking curtain wall with aluminium composite panel cladding, cleaning and protection ofthe curtain wall with aluminium compositepanel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevantaluminium item.sThe Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performancecharacteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shopdrawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external faceof the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimalplaces M2 1949.52 Included 0.00 0.00 0 0 0.00
122 7000018796 130 130 10 13. WATER PROOFING 120002831 995453 18 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen "and the like consisting of : i) Ist course of applying cement slurry @ 4.4 Kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) IInd course of 20mm cement plaster 1:3 (1 cement : 3 coarse sand)mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7Kg. per sqm of area. iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should" be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/sqm.) M2 150.60 Included 0.00 0.00 0 0 0.00
123 7000018796 130 130 20 13. WATER PROOFING 120002837 995453 18 22.7.1 Providing and laying integral cement based water proofing treatment including preparation of surface as required fortreatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75kg/sqm. of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slabincluding adjoining walls upto300mm height including cleaning the surface before treatment. b)Laying brick bats with mortar usingbroken bricks/brick bats 25 mm to115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand)admixed with water proofingcompound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5coarse sand ) admixed with waterproofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope andtreating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs c)After two days ofproper curing applying a second coat of cement slurry using 2.75kg/ sqm of cement admixed with water proofing compound conforming toIS : 2645 and approved by Engineer-in-charge. d)Finishing the surface with 20 mm thick jointless cement mortar of mix1:4 (1 cement:4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including layingglass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurryand making pattern of 300x300 mm square 3mm deep. e) The whole terrace so finished shall be flooded with water for a minimum periodof two weeks for curing and for final test. All above operations to be done in order and as directed and specified by theEngineer-in-Charge : With average thickness of 120mm and minimum thickness at khurra as 65 mm. M2 1429.56 Included 0.00 0.00 0 0 0.00
124 7000018796 130 130 30 13. WATER PROOFING 120003310 995453 18 22.23.1 Providing and applying integral crystalline slurry of hydrophilic innature for waterproofing treatment to the RCCstructures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior,sewage & water treatment plant, tunnels/subway and bridge decketc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystallineslurry : 2 parts water) forvertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same fromnegative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistantto 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The productperformance shall carry guarantee for 10 years against any leakage. (For vertical surface two coats @ 0.70 kg per sqm) M2 2186.47 Included 0.00 0.00 0 0 0.00
125 7000018796 130 130 40 13. WATER PROOFING 120003311 995453 18 22.23.2 Providing and applying integral crystalline slurry of hydrophilic innature for waterproofing treatment to the RCCstructures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior,sewage & water treatment plant, tunnels/subway and bridge decketc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystallineslurry : 2 parts water) forvertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same fromnegative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistantto 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The productperformance shall carry guarantee for 10 years against any leakage. (For horizontal surface one coat @1.10 kg per sqm.) M2 2922.30 Included 0.00 0.00 0 0 0.00
126 7000018796 130 130 50 13. WATER PROOFING 120003400 995421 18 22.26 Providing and applying of swellable type water stop tape, 19mm x 25mm thick in linear meter (expansive nature) forconstruction joints treatment of RCC structure such as raft slab, retaining walls, water storage tank and at the junctions of raftslab with the retaining walls etc.. After cleaning the surface, one coat of required primer for swellable water stop tape shall beapplied throughout the length of the joint @3.78 litre per 240 running meter. Over the primed surface swellable type water stop tapeshall be placed. The work shall be carried out all complete as per specification and the direction of the Engineer-In-Charge. RM 506.52 Included 0.00 0.00 0 0 0.00
CONDUITING WORKS
127 7000018796 140 140 10 14 .CONDUITING WORKS 130000093 995461 18 1.21.2 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. : 25 mm M 750.00 Included 0.00 0.00 0 0 0.00
128 7000018796 140 140 20 14 .CONDUITING WORKS 130000094 995461 18 1.21.3 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. : 32 mm M 750.00 Included 0.00 0.00 0 0 0.00
129 7000018796 140 140 30 14 .CONDUITING WORKS 120001147 995476 18 10.18 Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp of internal dia 140mm, 73mm height,top lid of 1.5mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S.sheet box by means of 3.3mm dia. round headed screws, one lock at the corners. Clamp shall be made of 12mm dia M.S. bar bent toshape as per standard drawing. EA 10.00 Included 0.00 0.00 0 0 0.00
SOIL INVESTIGATION
130 7000018796 150 150 10 15. SOIL INVESTIGATION 100001433 995435 18 Soil Investigation: As per technical specification including all laboratory and field tests, report and recommendations. LOT 1.00 Included 0.00 0.00 0 0 0.00
131 7000018796 160 160 10 16. OTHER ITEMS 170003873 995421 18 Antitermite Treatment Pre-Construction Providing and injection chemical emulsion for preconstructional antitermite treatment andcreating a chemical barrier under and around the column pits, wall trenches, basement excavation, top surface of plinth filingjunction of wall and floor, alongwith the external perimetre of building, expansion joints surrounding of pipes and conduite etc,complete (plinth area of the building at ground floor only shall be measured) Aldrin Embulsifiable concentrate (0.5%) M2 1773.39 Included 0.00 0.00 0 0 0.00
132 7000018796 160 160 20 16. OTHER ITEMS 170003874 995421 18 ANTI STATIC FLOORING Supply and installation of PUR homogeneous vinyl sheet flooring, 2 metre wide and overall thickness of 2mm. Theproduct should be homogeneous and single layered. The wear surface shall consist of impregnated polyurethane homogeneous mixture ofPVC with TRUESHIELD & Diamond 10 technology, Plasticizers without DOP, Urethane, color pigments and filler calendered to form asheet. Color and pattern details shall be dispersed throughout the thickness of the wear layer. Simpurity shall conform to group "T"wear resistance as per EN 649, Clean Room certified with class 'A' as per ASTMF5100, Flammability resistance of class Bfl-s1 as perEN13501-1, Dynamic coefficient of friction of class DS as per EN 13893, Impact sound reduction of 3dB as per ISO 10140, SlipResistance of class R9 as per DIN 51130, Color fastness rating of ≥6 as per ISO 105-B02, total weight being 3.3kg/m2 as per EN430.The product shall be suitable for applications in class 23/34/43 areas as per EN685. Product shall exhibit antistatic behaviour,resistance to bacteria,resistance to chemical, resistance to staining,suitability to castor chair. The product shall be FloorScorecertified with no SVHC content published by European Chemicals Agency(REACH). Product shall contribute to LEED points under Indoorenvironmental quality(LEED EQ) and Material & Resource (LEED MR) category. (Make :Armstrong World Industries, Gerfloor , wonderflooror equivalent ) M2 645.81 Included 0.00 0.00 0 0 0.00
133 7000018796 160 160 30 16. OTHER ITEMS 170003875 995421 18 Supply and installation of Vertical curve Blades Ceilings as per the design intent. The system comprises vertically curve bafflewith 100-150mm deep curved rafters manufactured out of 1.2 mm Aluminium to provide wave effect. The mod-ule for fixing baffle shallbe 150mm centres as per design require-ment. The carrier rails run perpendicular to the baffles axis and can be mounted with M6threaded rods using technical approved fasten-ers as per EN 13964 standards. The individual baffle lengths between 1200- 2400 mm canbe selected. Baffles lengths less than 1500mm required two carrier rails mounted at the baffle ends. Baffle longer than 1500mmrequire additional carrier rails mounted in the centre. Finish RAL Powder Coated No Pre-Coated products shall be accepted. Thespacing of the grid an-gles is according to the requirements of DIN 18168 and DIN EN 13964 and quality controlled to ISO 9001:2015approved by SIS & LEED cer-tification by Indian Green Building council (IGBC). GMS 1.2 carrier and 1.2 L angle. (Make Durlum,Harsons, Green, Dampa, Dexune, Armstrong, Hunter Douglous or equivalent) M2 532.92 Included 0.00 0.00 0 0 0.00
134 7000018796 160 160 40 16. OTHER ITEMS 170003876 995421 18 Supply and installation of plank ceiling of approved design with form fitting & tension free planks 300 Wide, upto 1500- 1800 mmLong manufactured of 0.7 mm AL. Perforation 1.8 dia holes with acoustic fleece soundtex tissue for 0.7 NRC The ceiling planks shallbe with square edges on 4 side. The substructure consisting of form punched angles as a lateral grid which is suspendedpressure-rigid from the bare ceiling with M6 threaded rods using officially approved dowel plugs. The angles are to be connected atthe ends by means of longitudinal connectors. The spacing of the grid angles is according to the requirements of DIN 18168 and DINEN 13964 and quality controlled to ISO 9001:2008 ap-proved by TUV. On the grid angles, Z-shaped carrier profiles are attached aslongitu-dinal profile with M6 bolts [secured against loosening]. The longitudi-nal connection of the Z-shaped carrier profiles ismade by means of profile connectors. The planks shall be manufactured on advanced equipment which includes several levelling stagesin manufacturing process. The plank ends will be raised with pips & stops to ensure ac-curate fixing & demounting of individualpanel. Panels to be installed in segmented curve pattern to achieve the design orientation. Speci-fication of sub structure will beas per the manufacturer recommen-dation. Finishes of ceiling planks shall be RAL powder coating with approved 3d printing on metalplanks. The spacing of the grid angles is accord-ing to the requirements of DIN 18168 and DIN EN 13964 and quality controlled to ISO9001:2015 approved by SIS & LEED certification by Indian Green Building council (IGBC). Finish Wood Grain 3D digital printingpattern (Make Durlum, Harsons, Green, Dampa, Dexune, Armstrong, Hunter Douglous or equivalent) M2 549.45 Included 0.00 0.00 0 0 0.00
135 7000018796 160 160 50 16. OTHER ITEMS 170003877 995421 18 Grid System False Ceiling Providing and fixing grid Wall angle of 19mmx19mmx0.40mm shall be screw fixed to brick wall/partition withthe help of approved screws at 600mm centres. Then suspending Main T grid of 15mm x 35mmx 0.3mm of length 3600mm is hung withadjustable level clips 85 x 31 x 0.6mm with 4mm Dia Rod which are connected to Soffit Cleat 37mmx27mmx1.6mm and 8mm dia 40mm longAnchor Fasteners @1200mm centres or as approved from RCC Slab.. The Cross T of 15mm x 35mmx0.3mm of 1200mm length shall beinterlocked between main T Grid at 600mm centres to form 1200 x 600mm modules. Then ceiling panel having FLB edge of size 600x1200mmshall be placed into the above grid of size 600x1200mm. This ceiling panel confirms to ASTM E84 surface burning characteristics.(Class A, Flame Spread<25 & Smoke developed<50). The Ceiling panel provides NRC 0.7, CAC minimum: 35. Light Reflectance: 88%, canwithstand Relative Humidity up to RH 99% (limiting conditions –Max 49 degree C/99%RH) and have Recycle content 61%. The tilecontains a broad-spectrum antimicrobial additive on the face and back of the panel that provides resistance against the growth ofmold and mildew. Third party certified for low-emitting performance as per ASTM Standard Guide D5116 - 10. USG Boral Microline 15mmTGrid System (600mm x 1200mm) or equivalent of make like Armstrong, Hunter Douglous, Dexune) " M2 329.23 Included 0.00 0.00 0 0 0.00
136 7000018796 160 160 60 16. OTHER ITEMS 170003878 995421 18 Fabric acoustical wall panelling Providing& fixing in position wall panelling at all heights of thickness 25 mm with Fiber GlassAcoustical Wall Panels of size 600x1500 mm creda or equivalent resin bonded square edges having NRC of 0.9 minimum. The panelsshould be manufactured from high density bio-soluble resin bonded glass wool absorber having density of 96 Kgs/m3 and wrapped on thefront side with an acoustically transparent fabric having option of colours and fabric type like jute, etc. as per approved byarchitect/engineer-in-charge plain tissue backer and fabric wrapped hardened edges. Panels should have humidity resistance up to 90%, thermal conductivity ≤ 0.03 (m² k / w) thermal resistance ≥ 0.9 (m² k / w) & moisture rate ≤ 1% (JC/T670 – 2005). Thepanel should be fully recycled and fire retardant as per Class A. The installation comprises a GI framework for acoustic wallpanelling as per design drawing (made from especially fabricated galvanized iron sheets 0.55 mm thick pressed section galvanizing @120 grams per sqm including both sides) consisting of floor channel of size 50X32X32X0.55 mm thick bottom and top fixed with nylonsleeves and screw. Further vertical GI studs of size 48X34X36X0.55 mm thick are placed at 600 mm center to center vertically on thewall using 12 mm dia 50 mm long wedged type expanded zinc alloy dash fastener with 10 mm bolt, to avoid any undulations on the wall.The extra channel must be used at openings and junctions as required. Further, wooden batten/ply of 6mm thickness and a width of5†to be placed at 600 mm center to center horizontally on the vertical GI Studs. Surface impalers of size 3â€X4†havingprojecting element called spikes shall be fixed on the wooden batten surface at 1200mm center to center horizontally and 600 mmcenter to center vertically, using self tapping screws. Silica based construction adhesive to be dabbed on to the projectingelements (spikes) of the impalers. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of theimpalers. Wall Panels shall be pierced through the spikes of the impalers ensuring line & level of panel are maintained. The panelsshould be mounted on the impalers horizontally or vertically as per the approved design or as per the directions of theengineer-in-charge. (Make Durlum, Harsons, Green, Dampa, Dexune, Credence or equivalent) M2 484.37 Included 0.00 0.00 0 0 0.00
137 7000018796 160 160 70 16. OTHER ITEMS 170003879 995421 18 Green Wall Providing & Fixing wall planter base pots in high quality unbreakable plasic in stackable mechanism which allowscascading iriigation method. The cost includes instlattion of different plant species as per direction of engg-incharge or byarchitect. The whole integrated system shall include the installation of framework, plants, irrigation system, HDPE drip pipe,Lateral dipper, Filters , joints & Auotmation timer etc. (Make Wonderwall, Four leaf, Bio Vertical or equivalent) M2 40.00 Included 0.00 0.00 0 0 0.00
138 7000018796 160 160 80 16. OTHER ITEMS 170003890 995421 18 HDHMR WALL PANELLING Providing and fixing factory made 30MM (18MM Flutes + 12 MM Base) thick Homogeneous HDHMR pasted on a 12 MMthick HDHMR Plain Board with a second Generation alumnimum polymer based hybrid All surface sealant, pressed in Temperature &Pressure controlled press, Solid Dark Green Colour board Fluting Panel, with CNC (Computer Numeric Control) Routed of approveddesign (Rectangular or Arched or both) by Engineer-in-charge which are machine cut for Panelling/Partitioning and acoustic Purposescomprising of Wood Fibre/Wood chips & synthetic thermosetting resin, having a minimum density of 820 kg/cum and screw Withdrawalstrength of 1500 N (Face), 1250 N (Edge), Modulus of Elasticity average, 3200N/mm2, Modulus of rupture average 3200N/mm2 withproperties of being termite/borer proof, moisture/water proof and fixing on Alumnimum frame made of 50 X 50 X 1.5 MM Square HollowBox section and screws etc., all complete as per direction of Engineer – in – chare. (Note; Alumnimum framework shall be paidseparately). (Make Greenlam, Ecoste, Century, Merlin Ply-la or equivalent) M2 170.98 Included 0.00 0.00 0 0 0.00
139 7000018796 160 160 90 16. OTHER ITEMS 170003891 995421 18 Providing and fixing Stainless steel 304 Grade H- type pull handle of size min 32 mm dia and 1200mm long of approved makeincluding SS screws, including making holes of required size in shutter etc. complete as per direction of Engineer-in-Charge. EA 32.00 Included 0.00 0.00 0 0 0.00
140 7000018796 160 160 100 16. OTHER ITEMS 170003892 995421 18 Providing and fixing SS Bottom patch Lock with cylinder of approved make including necessary screws etc. all complete. EA 21.00 Included 0.00 0.00 0 0 0.00
141 7000018796 160 160 110 16. OTHER ITEMS 170003893 995421 18 Providing and fixing SS floor mounted half dome door stopper of dia 45mm including necessary screws etc. all complete. EA 32.00 Included 0.00 0.00 0 0 0.00
142 7000018796 160 160 120 16. OTHER ITEMS 170003894 995421 18 Providing and fixing 12mm thk. Toughened float glass glazing cut and fixed in openings of desired shape as per drawing with 3/4"beveling all around, fixed with the help of SS patch fittings, with top and bottom 'C' channels, fixed firmly to the slab/ MSStructure ,as directed by Engineer in Charge. Area of openings to be measured). Assume frameless glass. Rate of above item toinclude P/F of : 20x20mm "C" channel SS patch Fittings. Glass Make: Saint gobain etc. & SS patch fitting make dorma, kich, gezeetc.or equivalent M2 661.36 Included 0.00 0.00 0 0 0.00
143 7000018796 160 160 130 16. OTHER ITEMS 170003895 995421 18 Auto mated Glass door Supply and fixing of Automatic frameless sliding door and operator, modular design including internal coverwith operator dimensions (H X T) not exceeding 120mm x 175mm and of length required to suit the opening size given below: Clearopening of size 2500mm X 2400mm: EC Drive, compact linear sliding door automatic, with self cleaning rollers, TUV type tested asper DIN 18650. In general, the sliding door consists of 16 bit Microprocessor Control unit, monitoring of closing force, automaticreverse on contact with obstruction, operator commissioning without any additional instrumentation and self-teaching. OperatingModes: Continuous open, automatic operation, closing time, night lock, multi-sensor detector(radar motion detector with directiondetection and self-monitoring, (light barrier) for convenient safeguarding of the opening width),(Option: Electromagnetic locking,integrated in the drive unit, with manual emergency unlocking.) The operator will be provided with short circuit proof power supplyunit 220 / 240 V, 50 / 60 hz (power point shall be made available at site by electrical contractor). Operator shall have openingspeed adjustable from 10 to 60 cm / sec / leaf, closing speed adjustable from 10 to 55 cm / sec / leaf, adjustable creep speed 3 - 9cm / sec / leaf and adjustable hold open time 0 - 180 seconds all confirming to manufacturers specification. Rate is not includedfor providing 12mm thick clear toughened glass sliding shutter as per design, handling, loading and unloading, installation, powerrequired for erection, protecting the module and glass till handing over, testing, commissioning all necessary hardware’s and themodule to be erected with the structural supports etc. complete and all as per manufacturers specifications as directed: ( 12mmthick toughened glass shutter shall be paid extra.) (Makes GEZE ,SIO, Dorma, or Equivalent) EA 1.00 Included 0.00 0.00 0 0 0.00
144 7000018796 160 160 140 16. OTHER ITEMS 170003896 995421 18 Supply and Installation of Vertical Louvers, CS-200 or equivalent Vertical Fin system of approved shade and design components hasto be in Aluminum extrusion Alloy 6063-T5/T6/1100/3000 Series, with minimum thickness of the extruded minimum 1.5 mm, with BladesMulti tube tapered from 27†down to 10†projection, extruded aluminum rectangular tube design. Tubes shall be factory assembledto outriggers using stainless steel, type F, thread cutting screws through internal screw slots in blades. Welding is notacceptable. Blades to be mechanically secured to allow for replacement in case of damage. Fasteners to be hex head. All thefasteners used shall be of Stainless steel for the construction of the louvers and should be mechanically fastened. Louver must befactory fabricated and finish so that only assembly/ installation will be done at the site. Finish will as per the approved RALcolor in Super durable Powder Coat System, Complying with AAMA-2604 standards. Finish thickness to be minimum 2 mils. (Make:Construction Specialties group Industrial Louvers, Hunter Douglas or equivalent) M2 1591.66 Included 0.00 0.00 0 0 0.00
145 7000018796 160 160 150 16. OTHER ITEMS 170003897 995421 18 Supply and fixing Aluminium Double Fin Aerobrise 400 plain Louver motorized adjustable System consists of extruded aluminium squareshaft & butterfly clamps covered with aluminium metal cover skin on both sides, ‘V’ shaped aluminium fin skin with crowningmanufactured out of 0.7mm precoated aluminium alloy AA 3005 fixed on both sides of square shaft, fin bearing block, axle, axle lock,nylon end cap & driving end cap, end cap screws, and end cap connector & accessories for adjustable system consists of actuator,driving control consists of driving rod connector, actuator suspension bracket, Aluminum /steel driving rod standard length up to3000mm. The maximum module of fin for adjustable system is 395mm and the length of fin shall be determined based on the wind loadcalculation and deflection. The factory assembled Aerobrise 300mm fin will be fixed on both ends to suitable Installation frames ofMS sections/Aluminum provided by others. The installation frame shall be fixed mechanically to concrete structure with MS orAluminum brackets. The erected substructure shall be aligned within the tolerances of ± span/1000 of plumb line and level with anoncumulative tolerance of a maximum of 2 mm. The louver Fin skin & shall be coil coated in PVDF finish or suitable for exteriorapplications. The system shall be connected to 12V motors supplied by. Surface Treatment: Polyester Powder Coated exterior finishaccording to RAL9010 Standard Color (WHITE. (Make :Construction Specialties group Industrial Louvers, Airolite, Hunter Douglas orequivalent) M2 521.36 Included 0.00 0.00 0 0 0.00
146 7000018796 160 160 160 16. OTHER ITEMS 170003898 995421 18 Providing and fixing 8"x8" size 6MM acrylic with a layer of 1MM PVC material name plate having PGCIL lettering and graphics. 5/8â€tall tactile letters in futura medium type face. 4.5†tall tactile symbols. Letters and symbols chemically welded to and raised1/32 inch above plaque surface. PGCIL compliant Grade 2 doomed braille positioned 3/8 inch below text.All signs to comply with PGCILspecifications.Name plate of Title Name,Ladies Toilet,Gents toilet and Handicap Toilet. EA 10.00 Included 0.00 0.00 0 0 0.00
147 7000018796 160 160 170 16. OTHER ITEMS 170003899 995421 18 Providing and fixing 36"x24" size 6MM acrylic with a layer of 1MM PVC material. Having PGCIL lettering and graphics. 5/8†talltactile letters in futura medium typeface. 4.5†tall tactile symbols. Letters and symbols chemically welded to and raised 1/32inch above plaque surface. PGCIL compliant Grade 2 doomed braille positioned 3/8 inch below text. All signs to comply with PGCILspecifications.Name plate of EVACUTION PLAN and FLOOR DIRECTORY.All signage are photoluminescent. EA 10.00 Included 0.00 0.00 0 0 0.00
148 7000018796 160 160 180 16. OTHER ITEMS 170003900 995421 18 Providing and fixing 8"x8" size 6MM acrylic with a layer of 1MM PVC material. Having PGCIL lettering and graphics. 5/8†talltactile letters in futura medium typeface. 4.5†tall tactile symbols. Letters and symbols chemically welded to and raised 1/32inch above plaque surface. PGCIL compliant Grade 2 doomed braille positioned 3/8 inch below text. All signs to comply with PGCILspecifications.Name plate of IN CASE OF FIRE (PL).All signage are photoluminescent. EA 10.00 Included 0.00 0.00 0 0 0.00
149 7000018796 160 160 190 16. OTHER ITEMS 170003901 995421 18 Providing and fixing 18"x18" size 6MM acrylic with a layer of 1MM PVC material. Having PGCIL lettering and graphics. 5/8†talltactile letters in futura medium typeface. 4.5†tall tactile symbols. Letters and symbols chemically welded to and raised 1/32inch above plaque surface. PGCIL compliant Grade 2 doomed braille positioned 3/8 inch below text. All signs to comply with PGCILspecifications.Name plate of LIFT SIGNAGE SET.All signage are photoluminescent. EA 5.00 Included 0.00 0.00 0 0 0.00
150 7000018796 160 160 200 16. OTHER ITEMS 170003902 995421 18 Providing and fixing 18"x6" size 6MM acrylic with a layer of 1MM PVC material. Having PGCIL lettering and graphics. 5/8†talltactile letters in futura medium typeface. 4.5†tall tactile symbols. Letters and symbols chemically welded to and raised 1/32inch above plaque surface. PGCIL compliant Grade 2 doomed braille positioned 3/8 inch below text. All signs to comply with PGCILspecifications.Name plate of FINAL EXIT DOOR (PL) , EXIT ARROW DIRECTION (PL)and FIRE EXIT (PL).All signage are photoluminescent. EA 20.00 Included 0.00 0.00 0 0 0.00
151 7000018796 160 160 210 16. OTHER ITEMS 170003903 995421 18 Providing and fixing 24"x4" size 6MM acrylic with a layer of 1MM PVC material. Having PGCIL lettering and graphics. 5/8†talltactile letters in futura medium typeface. 4.5†tall tactile symbols. Letters and symbols chemically welded to and raised 1/32inch above plaque surface. PGCIL compliant Grade 2 doomed braille positioned 3/8 inch below text. All signs to comply with PGCILspecifications.Name plate of PUSH BAR TO OPEN (PL).All signage are photoluminescent. EA 10.00 Included 0.00 0.00 0 0 0.00
152 7000018796 160 160 220 16. OTHER ITEMS 170003904 995421 18 Providing and fixing 8"x10" size 6MM acrylic with a layer of 1MM PVC material. Having PGCIL lettering and graphics. 5/8†talltactile letters in futura medium typeface. 4.5†tall tactile symbols. Letters and symbols chemically welded to and raised 1/32inch above plaque surface. PGCIL compliant Grade 2 doomed braille positioned 3/8 inch below text. All signs to comply with PGCILspecifications.Name plate of FIRE HOSE REEL (PL) and FIRE EXTINGUISHER (PL).All signage are photoluminescent. EA 10.00 Included 0.00 0.00 0 0 0.00
153 7000018796 160 160 230 16. OTHER ITEMS 170003905 995421 18 Providing and fixing LOGO Halo Illuminated Letters of 24" height following :Spec - Individual letters reading 'POWERGRID' ral9005 jet black descaled acrylic letters with gloss finish return with black acrylic followed by equal size white acrylic haloilluminated black acrylic letter return will be equal to width of stroke of letter "m" acrylic sheet to be used to form blackacrylic letters – seamless joint finish required all wires to be concealed in flexible conduit light color temperature – 5000k(manufacturer’s color temperature certificate required post execution) EA 1.00 Included 0.00 0.00 0 0 0.00
154 7000018796 160 160 240 16. OTHER ITEMS 170003906 995421 18 Providing and fixing EXTERNAL DIRECTORIES of size 72"x10" Sign Panel, sides - front and back Illuminated, 1mm aluminium sheetwith laser cut graphics, painted to required colour. Fixed to aluminium extrusion structure using VHB tapes. Acrylic sheet of 3mm,040 opacity fixed in graphic space from inside. Illumination provided by LED modules from inside. Modules of 0.72W with 12V or 24Vsupply with 3 years life. EA 2.00 Included 0.00 0.00 0 0 0.00
155 7000018796 160 160 250 16. OTHER ITEMS 170003907 995421 18 Providing and fixing EXTERNAL DIRECTORIES Support Structure : two poles Of stainless steel grade-304, sqaure pipe ofsize-75mmX75mmX1mm of length- 10' fixed with use of SS 304 anchor plates of size - 200mmX2mmX4mm fixed to RCC base with anchorfastners RCC Base : size - 24"x18"x18" grade - M25 EA 2.00 Included 0.00 0.00 0 0 0.00
156 7000018796 160 160 260 16. OTHER ITEMS 170003908 995421 18 Providing and fixing Architectural facade panels of composite wood and cement. Thickness of boards is 12mm and max. size 3000 x 1250mm. The joints between boards must always be manifest with a minimum spacing of 5mm it to be filled a top quality polyurethane, MSpolymer or hybrid elastomer mastic should be used. Protecting the board by applying paint or varnish. The board to be sanded. Whenthe board is sanded, wood particles become visible on the board surface. The thickness tolerance of the board is ± 0.3 mm.Vibratory disk or belt sanders to be used. The board to be fastened using a bonding system on GI metal support structures. Thescrewing is most common system use for attaching due to the ease implementation and efficiency. The shrinkage of the panel may be5mm /m(0.5%). M2 114.98 Included 0.00 0.00 0 0 0.00
157 7000018796 160 160 270 16. OTHER ITEMS 170003909 995421 18 Providing and fixing mild steel (MS) puddle flanges of required size with 6mm thick mild steel (MS) plate including necessarywelding as per details shown on drawings and directions of Engineer-in-charge for water tanks. 25mm dia (4mm wall thickness) EA 6.00 Included 0.00 0.00 0 0 0.00
158 7000018796 160 160 280 16. OTHER ITEMS 170003910 995421 18 Providing and fixing mild steel (MS) puddle flanges of required size with 6mm thick mild steel (MS) plate including necessarywelding as per details shown on drawings and directions of Engineer-in-charge for water tanks. 100mm dia (6mm wall thickness) EA 8.00 Included 0.00 0.00 0 0 0.00
159 7000018796 160 160 290 16. OTHER ITEMS 170003911 995421 18 Providing and fixing mild steel (MS) puddle flanges of required size with 6mm thick mild steel (MS) plate including necessarywelding as per details shown on drawings and directions of Engineer-in-charge for water tanks. 150mm dia (6mm wall thickness) EA 4.00 Included 0.00 0.00 0 0 0.00
160 7000018796 160 160 300 16. OTHER ITEMS 170003912 995421 18 Providing and fixing mild steel (MS) puddle flanges of required size with 6mm thick mild steel (MS) plate including necessarywelding as per details shown on drawings and directions of Engineer-in-charge for water tanks. 200mm dia (6mm wall thickness) EA 2.00 Included 0.00 0.00 0 0 0.00
161 7000018796 160 160 310 16. OTHER ITEMS 170003913 995421 18 Providing and fixing machine cut, mirror / eggshell polished , Granite stone work for wall lining (veneer work) including dado,skirting, risers of steps etc., in required design and pattern wherever required, stones of different finished surface texture, on12mm (average) thick cement mortar 1:3 (1 cement : 3 oarse sand) laid and jointed with white cement slurry @ 3.3 kg/Sq.Mt. includingpointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing, polishing etc. all complete asper Architectural drawings, and as directed by the Engineer-in-Charge. a. 18 mm thick Granite stone slab any colour etc. M2 1094.67 Included 0.00 0.00 0 0 0.00
SANITARY INSTALLATION
162 7000018796 170 170 10 17. SANITARY INSTALLATION 170003914 995421 18 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 3/6 litre low levelwhite dual flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with allfittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI markedwhite solid plastic seat and lid.Make:Roca (Giralda-RS346467460) or Equivalent. EA 14.00 Included 0.00 0.00 0 0 0.00
163 7000018796 170 170 20 17. SANITARY INSTALLATION 170003915 995421 18 Supplying,Fixing, testing & commissioning of ABS Rinsing spray with regulator of flexible pipe , wall hooked complete as required. EA 14.00 Included 0.00 0.00 0 0 0.00
164 7000018796 170 170 30 17. SANITARY INSTALLATION 170003916 995421 18 Providing and fixing white vitreous china battery based infrared sensor operated urinal sutaible size having pre & post flushingwater inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction ofEngineer-in-charge. Make :Roca Urinal (RS35945J460), Capricon Sensor or Equivalent. EA 11.00 Included 0.00 0.00 0 0 0.00
165 7000018796 170 170 40 17. SANITARY INSTALLATION 170003917 995421 18 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever require: Make : Jaquar, Roca, Grohe orEquivalent EA 14.00 Included 0.00 0.00 0 0 0.00
166 7000018796 170 170 50 17. SANITARY INSTALLATION 120001899 995478 18 17.10.1.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steelplug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required (Kitchen sink with drainboard ) : 510x1040 mm bowl depth 250mm. EA 1.00 Included 0.00 0.00 0 0 0.00
167 7000018796 170 170 60 17. SANITARY INSTALLATION 120001904 995478 18 17.10.2.2 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steelplug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required (Kitchen sink withoutdrain board ) : 610x460 mm bowl depth 200 mm. EA 2.00 Included 0.00 0.00 0 0 0.00
168 7000018796 170 170 70 17. SANITARY INSTALLATION 170003919 995421 18 Providing and fixing beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixedto wooden cleats with C.P. brass screws and washers complete. M2 14.00 Included 0.00 0.00 0 0 0.00
169 7000018796 170 170 80 17. SANITARY INSTALLATION 170003920 995421 18 Providing and fixing toilet paper holder :C.P. brass EA 14.00 Included 0.00 0.00 0 0 0.00
170 7000018796 170 170 90 17. SANITARY INSTALLATION 170003921 995421 18 Providing and fixing liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket ofthe same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. EA 8.00 Included 0.00 0.00 0 0 0.00
171 7000018796 170 170 100 17. SANITARY INSTALLATION 170003922 995421 18 Providing and fixing CP Brass 32mm size bottle trap of approved quality & make and as per the direction of engineer in charge. EA 14.00 Included 0.00 0.00 0 0 0.00
172 7000018796 170 170 110 17. SANITARY INSTALLATION 170003923 995421 18 Providing and fixing Coat Hook. EA 14.00 Included 0.00 0.00 0 0 0.00
173 7000018796 170 170 120 17. SANITARY INSTALLATION 170003924 995421 18 Providing ,Fixing of straight / offset type flexible single body push fit type WC pan connector of with integral single mouldsealing fins made of flexible EVA body to be fixed with manufacture supplied grease, including rubber bush / adaptor for use withC.I pipe as supplied with the pan connector. EA 14.00 Included 0.00 0.00 0 0 0.00
174 7000018796 170 170 130 17. SANITARY INSTALLATION 170003925 995421 18 Providing and fixing solid state, no touch operting, fully hygienic hand drier of approved shade with single blower, with timedelay, summer & winter control, music while drying, volume ON/OFF controls including providing necessary brackets, cable from drierto Plug, Plug top key and lock etc, complete as required. EA 5.00 Included 0.00 0.00 0 0 0.00
175 7000018796 170 170 140 17. SANITARY INSTALLATION 170003926 995421 18 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690gms. 15 mm nominal bore Make : Jaquar, Roca, Grohe or Equivalent EA 3.00 Included 0.00 0.00 0 0 0.00
176 7000018796 170 170 150 17. SANITARY INSTALLATION 170003927 995421 18 Providing and fixing C.P. brass angle valve for basin mixer and healt feauset of approved quality 15mm nominal bore.Make : Jaquar,Roca, Grohe or Equivalent EA 42.00 Included 0.00 0.00 0 0 0.00
177 7000018796 170 170 160 17. SANITARY INSTALLATION 170003928 995421 18 Fixing, testing and commissioning of S.S braided flexible connection 375 mm long including nuts and washers and making connectionto fixtures and fittings complete as required. EA 42.00 Included 0.00 0.00 0 0 0.00
178 7000018796 170 170 170 17. SANITARY INSTALLATION 170003929 995421 18 Providing & Fixing of Grab bar 600 mm of non slipping grip as per standard specification of use in disabled toilet complete withbrackets suitable for wall installation as per approved sample complete in all respect. EA 1.00 Included 0.00 0.00 0 0 0.00
179 7000018796 170 170 180 17. SANITARY INSTALLATION 170003930 995421 18 Providing and Fixing SS Swing grab bar, fixed to PVC cleats with C.P. brass screws wherever required with approved make & qualityand as per the directions and to the satisfaction of Engineer-in-charge. EA 1.00 Included 0.00 0.00 0 0 0.00
180 7000018796 170 170 190 17. SANITARY INSTALLATION 170003931 995421 18 Providing and fixing S.S. body tissue paper dispenser fixed to PVC cleats with C.P. brass screws wherever required of approvedmake & quality and as per the directions and to the satisfaction of the Engineer-in-charge. EA 5.00 Included 0.00 0.00 0 0 0.00
181 7000018796 170 170 200 17. SANITARY INSTALLATION 170003932 995421 18 Providing and fixing SS grating of approved quality and colour.Circular type 100 mm nominal dia EA 7.00 Included 0.00 0.00 0 0 0.00
182 7000018796 170 170 210 17. SANITARY INSTALLATION 170003933 995421 18 Providing and fixing SS grating of approved quality and colour.Circular type 125 mm nominal dia with 25 mm waste hole EA 21.00 Included 0.00 0.00 0 0 0.00
183 7000018796 170 170 220 17. SANITARY INSTALLATION 120001366 995453 18 12.44 Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440grams. EA 6.00 Included 0.00 0.00 0 0 0.00
184 7000018796 170 170 230 17. SANITARY INSTALLATION 170003934 995421 18 Supplying & Fixing of Storage Type Water Heater of approved shade with copper container, glasswool insulation,stove enamelled M.Sjacket, thermostatically controlled inner heater with pilot neon lamps, angle valve on inlet connection, 15mm dia C.P,S.S braidedflexible connection in inlet & outlet suitable for working pressure of 5/ 8 kg/sqcm complete as required.Cap-15 lit EA 1.00 Included 0.00 0.00 0 0 0.00
INTERNAL WATER SUPPLY SYSTEM
185 7000018796 180 180 10 18. INTERNAL WATER SUPPLY SYSTEM 120002102 995424 18 18.7.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 15 mm nominal outer dia .Pipes. M 12.00 Included 0.00 0.00 0 0 0.00
186 7000018796 180 180 20 18. INTERNAL WATER SUPPLY SYSTEM 120002103 995424 18 18.7.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 20 mm nominal outer dia .Pipes. M 50.00 Included 0.00 0.00 0 0 0.00
187 7000018796 180 180 30 18. INTERNAL WATER SUPPLY SYSTEM 120002104 995424 18 18.7.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 25 mm nominal outer dia .Pipes. M 245.00 Included 0.00 0.00 0 0 0.00
188 7000018796 180 180 40 18. INTERNAL WATER SUPPLY SYSTEM 120002105 995424 18 18.7.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 32 mm nominal outer dia .Pipes. M 26.00 Included 0.00 0.00 0 0 0.00
189 7000018796 180 180 50 18. INTERNAL WATER SUPPLY SYSTEM 120002106 995424 18 18.7.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 40 mm nominal outer dia .Pipes. M 52.00 Included 0.00 0.00 0 0 0.00
190 7000018796 180 180 60 18. INTERNAL WATER SUPPLY SYSTEM 120002107 995424 18 18.7.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 50 mm nominal outer dia .Pipes. M 115.00 Included 0.00 0.00 0 0 0.00
191 7000018796 180 180 70 18. INTERNAL WATER SUPPLY SYSTEM 120002108 995424 18 18.8.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge. :Concealed work etc. : 15 mm nominal outer dia .Pipes. M 35.00 Included 0.00 0.00 0 0 0.00
192 7000018796 180 180 80 18. INTERNAL WATER SUPPLY SYSTEM 120002109 995424 18 18.8.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge. :Concealed work etc. : 20 mm nominal outer dia .Pipes. M 51.00 Included 0.00 0.00 0 0 0.00
193 7000018796 180 180 90 18. INTERNAL WATER SUPPLY SYSTEM 120002110 995424 18 18.8.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing ofjoints complete as per direction of Engineer in Charge. :Concealed work etc. : 25 mm nominal outer dia .Pipes. M 6.00 Included 0.00 0.00 0 0 0.00
194 7000018796 180 180 100 18. INTERNAL WATER SUPPLY SYSTEM 120002147 995424 18 18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore EA 13.00 Included 0.00 0.00 0 0 0.00
195 7000018796 180 180 110 18. INTERNAL WATER SUPPLY SYSTEM 120002148 995424 18 18.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore EA 13.00 Included 0.00 0.00 0 0 0.00
196 7000018796 180 180 120 18. INTERNAL WATER SUPPLY SYSTEM 120002149 995424 18 18.17.5 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore EA 1.00 Included 0.00 0.00 0 0 0.00
197 7000018796 180 180 130 18. INTERNAL WATER SUPPLY SYSTEM 120002153 995424 18 18.18.3 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mmnominal bore EA 10.00 Included 0.00 0.00 0 0 0.00
198 7000018796 180 180 140 18. INTERNAL WATER SUPPLY SYSTEM 170003935 995421 18 Providing & fixing Auto Air vent for cold water supply risers, suitable for pressure not less than 15 Kg/Sq.cm. 15mm EA 2.00 Included 0.00 0.00 0 0 0.00
199 7000018796 180 180 150 18. INTERNAL WATER SUPPLY SYSTEM 170003936 995421 18 Providing, fixing, testing and commissioning moterise Ball valve of following sizes, for filling of overhead tanks complete withhigh & low level switchs & pressure switch to control the valve. The level controller shalll be installed in over head tank. Thelevel switch will close the valve when water level is high & open the valve when level is low in the tank. The system should becomplete in all respect with accessories, 220V AC / 24 V DC, IP 67 water level control unit, Control Panel, copper control wiring inwhether proof casing etc. 40 mm dia EA 2.00 Included 0.00 0.00 0 0 0.00
200 7000018796 180 180 160 18. INTERNAL WATER SUPPLY SYSTEM 170003937 995421 18 Providing, fixing, testing and commissioning moterise Ball valve of following sizes, for filling of overhead tanks complete withhigh & low level switchs & pressure switch to control the valve. The level controller shalll be installed in over head tank. Thelevel switch will close the valve when water level is high & open the valve when level is low in the tank. The system should becomplete in all respect with accessories, 220V AC / 24 V DC, IP 67 water level control unit, Control Panel, copper control wiring inwhether proof casing etc. 50 mm dia EA 1.00 Included 0.00 0.00 0 0 0.00
201 7000018796 180 180 170 18. INTERNAL WATER SUPPLY SYSTEM 170003938 995421 18 Supplying, Installation Testing & commisioning of floor mounted storage water cooler of suitable capacity made of Stainless steelbody with PUF insulation, SS storage tank and extra large SS tray to prevent splashing of water to ensure quick drainage. Thecomplete unit shall be compact, eco- friendly with externally mounted thermostat for easy setting of temperature complete asrequired. the system shall be factory assembeled and tested. Storage Capacity 80 Ltrs, Cooling capacity -60 Ltrs/hr, Fecuet-2 EA 1.00 Included 0.00 0.00 0 0 0.00
202 7000018796 180 180 180 18. INTERNAL WATER SUPPLY SYSTEM 170003939 995421 18 Supplying, installation, testing and commissioning of the UV unit shall have with reactor, cabinet housing, treatment chamber,electrical panel lampout alert,UV system for disinfection shall utilize high purity fused quartz sleeves UV Reactor MOC will beSS304. System shall be designed to provide a UV Dose of > 30,000 uW – Sec / sq.cm. The electrical control system should utilizehigh frequency electronic ballasts and provide efficiency of more then 90%. The Reactor should be Pickled, passivated &electropolished. The oring should be food grade EPDM as per US FDS 21 CFR.(Cold water & Normal water)Make- Alfaa(Model no - ECS25L)or equivalent." SET 1.00 Included 0.00 0.00 0 0 0.00
INTERNAL DRAINAGE SYSTEM
203 7000018796 190 190 10 19. INTERNAL DRAINAGE SYSTEM 170003940 995421 18 Fixing, jointing, testing and commissioning of SWR pipe (type-B ) conforming to IS- 13592:92 soil, waste & vent pipes cutto required lengths . Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. Making properconnection with solvent type joint of required depth as per BIS / manufacturer. Cutting, chases/holes in floors / walls / slab.110 mm dia M 152.00 Included 0.00 0.00 0 0 0.00
204 7000018796 190 190 20 19. INTERNAL DRAINAGE SYSTEM 170003941 995421 18 Fixing, jointing, testing and commissioning of SWR pipe (type-B ) conforming to IS- 13592:92 soil, waste & vent pipes cutto required lengths . Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. Making properconnection with solvent type joint of required depth as per BIS / manufacturer. Cutting, chases/holes in floors / walls / slab.75 mm dia M 35.00 Included 0.00 0.00 0 0 0.00
205 7000018796 190 190 30 19. INTERNAL DRAINAGE SYSTEM 170003942 995421 18 Providing and fixing SWR fittings conforming to IS- 14735:99 bend of required degree with access door, insertion rubber washer,bolts and nuts etc.110 mm dia EA 6.00 Included 0.00 0.00 0 0 0.00
206 7000018796 190 190 40 19. INTERNAL DRAINAGE SYSTEM 170003943 995421 18 Providing and fixing SWR fittings conforming to IS- 14735:99 plain bend of required degree. 110 mm dia EA 56.00 Included 0.00 0.00 0 0 0.00
207 7000018796 190 190 50 19. INTERNAL DRAINAGE SYSTEM 170003944 995421 18 Providing and fixing SWR fittings conforming to IS- 14735:99 plain bend of required degree 75 mm dia EA 2.00 Included 0.00 0.00 0 0 0.00
208 7000018796 190 190 60 19. INTERNAL DRAINAGE SYSTEM 170003945 995421 18 Providing and fixing SWR single equal plain junction of required degree with access door, insertion rubber washer, bolts and nutscomplete.110x110x110 mm EA 6.00 Included 0.00 0.00 0 0 0.00
209 7000018796 190 190 70 19. INTERNAL DRAINAGE SYSTEM 170003946 995421 18 Providing and fixing SWR single equal plain junction of required degree :110x110x110 mm EA 43.00 Included 0.00 0.00 0 0 0.00
210 7000018796 190 190 80 19. INTERNAL DRAINAGE SYSTEM 170003947 995421 18 Providing and fixing SWR single unequal plain junction of required degree :110x110x75 mm EA 4.00 Included 0.00 0.00 0 0 0.00
211 7000018796 190 190 90 19. INTERNAL DRAINAGE SYSTEM 170003948 995421 18 Providing and fixing SWR vent cowel. 110mm EA 2.00 Included 0.00 0.00 0 0 0.00
212 7000018796 190 190 100 19. INTERNAL DRAINAGE SYSTEM 170003949 995421 18 Providing and fixing SWR vent cowel. 75mm EA 1.00 Included 0.00 0.00 0 0 0.00
213 7000018796 190 190 110 19. INTERNAL DRAINAGE SYSTEM 170003950 995421 18 Providing and fixing SWR trap of self cleansing design with screwed down or hinged grating with or without vent arm complete,including cost of cutting and making good the walls and floors : 110 mm inlet and 110 mm outlet EA 22.00 Included 0.00 0.00 0 0 0.00
214 7000018796 190 190 120 19. INTERNAL DRAINAGE SYSTEM 170003951 995421 18 Providing and fixing SWR Floor/ceiling Clean Out plug as required,complete as per instruction of the Engineer in charge.110 mm dia EA 10.00 Included 0.00 0.00 0 0 0.00
215 7000018796 190 190 130 19. INTERNAL DRAINAGE SYSTEM 170003952 995421 18 Fixing, jointing, testing and commissioning of UPVC pipe conforming to IS:4985 of 6 Kg/Sq. cm rating cut to requiredlengths including all necessary fittings as IS:7834(moulded) & IS:10124 (fabricated) and specials such as Bends, junctions,offsets, access pieces (plain or door) & vent cowl. Fixing at wall/ceiling level supported by galvanized steel clamps & hangersetc. Making proper connection with solvent type joint of required depth as per BIS / manufacturer. Cutting, chases/holesin floors / walls / slab. (WB/UR/FDSINK) 32 mm dia M 13.00 Included 0.00 0.00 0 0 0.00
216 7000018796 190 190 140 19. INTERNAL DRAINAGE SYSTEM 170003953 995421 18 Fixing, jointing, testing and commissioning of UPVC pipe conforming to IS:4985 of 6 Kg/Sq. cm rating cut to requiredlengths including all necessary fittings as IS:7834(moulded) & IS:10124 (fabricated) and specials such as Bends, junctions,offsets, access pieces (plain or door) & vent cowl. Fixing at wall/ceiling level supported by galvanized steel clamps & hangersetc. Making proper connection with solvent type joint of required depth as per BIS / manufacturer. Cutting, chases/holesin floors / walls / slab. (WB/UR/FDSINK) 40 mm dia M 3.00 Included 0.00 0.00 0 0 0.00
217 7000018796 190 190 150 19. INTERNAL DRAINAGE SYSTEM 170003954 995421 18 Fixing, jointing, testing and commissioning of UPVC pipe conforming to IS:4985 of 6 Kg/Sq. cm rating cut to requiredlengths including all necessary fittings as IS:7834(moulded) & IS:10124 (fabricated) and specials such as Bends, junctions,offsets, access pieces (plain or door) & vent cowl. Fixing at wall/ceiling level supported by galvanized steel clamps & hangersetc. Making proper connection with solvent type joint of required depth as per BIS / manufacturer. Cutting, chases/holesin floors / walls / slab. (WB/UR/FDSINK) 50 mm dia M 7.00 Included 0.00 0.00 0 0 0.00
218 7000018796 190 190 160 19. INTERNAL DRAINAGE SYSTEM 170003955 995421 18 Providing and fixing 110mm dia SWR multi- inlet fitting consisting of 110mm dia length main SWR pipe with multiple SWR sockets(Inlets) of required diameter (as per site requirement) and fixing the same to SWR trap and setting in cement concrete, completeas per instructions of the Engineer in charge. EA 21.00 Included 0.00 0.00 0 0 0.00
219 7000018796 190 190 170 19. INTERNAL DRAINAGE SYSTEM 170003956 995421 18 Fixing, jointing, testing and commissioning of UPVC pipe conforming to IS:4985 of 6 Kg/Sq. cm rating cut to requiredlengths including all necessary fittings as IS:7834(moulded) & IS:10124 (fabricated) and specials such as Bends, junctions,offsets, access pieces (plain or door) & vent cowl. Fixing at wall/ceiling level supported by galvanized steel clamps & hangersetc. Making proper connection with solvent type joint of required depth as per BIS / manufacturer. Cutting, chases/holesin floors / walls / slab. (Rain water pipe)110 mm dia M 10.00 Included 0.00 0.00 0 0 0.00
220 7000018796 190 190 180 19. INTERNAL DRAINAGE SYSTEM 170003957 995421 18 Fixing, jointing, testing and commissioning of UPVC pipe conforming to IS:4985 of 6 Kg/Sq. cm rating cut to requiredlengths including all necessary fittings as IS:7834(moulded) & IS:10124 (fabricated) and specials such as Bends, junctions,offsets, access pieces (plain or door) & vent cowl. Fixing at wall/ceiling level supported by galvanized steel clamps & hangersetc. Making proper connection with solvent type joint of required depth as per BIS / manufacturer. Cutting, chases/holesin floors / walls / slab. (Rain water pipe)160 mm dia M 225.00 Included 0.00 0.00 0 0 0.00
EXTERNAL WATER SUPPLY
221 7000018796 200 200 10 20.EXTERNAL WATER SUPPLY 120002116 995424 18 18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. :External work : 40 mm nominal outer dia.Pipes. M 15.00 Included 0.00 0.00 0 0 0.00
222 7000018796 200 200 20 20.EXTERNAL WATER SUPPLY 120002117 995424 18 18.9.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. :External work : 50 mm nominal outer dia.Pipes. M 2.00 Included 0.00 0.00 0 0 0.00
223 7000018796 200 200 30 20.EXTERNAL WATER SUPPLY 120002118 995424 18 18.9.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. :External work : 62.50 mm nominal innerdia Pipes. M 2.00 Included 0.00 0.00 0 0 0.00
224 7000018796 200 200 40 20.EXTERNAL WATER SUPPLY 120002119 995424 18 18.9.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. :External work : 75 mm nominal inner dia.Pipes. M 20.00 Included 0.00 0.00 0 0 0.00
225 7000018796 200 200 50 20.EXTERNAL WATER SUPPLY 120002258 995424 18 18.41.5 Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. : 40 mm diameterpipe M 15.00 Included 0.00 0.00 0 0 0.00
226 7000018796 200 200 60 20.EXTERNAL WATER SUPPLY 120002259 995424 18 18.41.6 Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. : 50 mm diameterpipe M 2.00 Included 0.00 0.00 0 0 0.00
227 7000018796 200 200 70 20.EXTERNAL WATER SUPPLY 120002260 995424 18 18.41.7 Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. : 65 mm diameterpipe M 2.00 Included 0.00 0.00 0 0 0.00
228 7000018796 200 200 80 20.EXTERNAL WATER SUPPLY 120002261 995424 18 18.41.8 Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. : 80 mm diameterpipe M 20.00 Included 0.00 0.00 0 0 0.00
229 7000018796 200 200 90 20.EXTERNAL WATER SUPPLY 120002262 995424 18 18.41.9 Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. : 100 mm diameterpipe M 80.00 Included 0.00 0.00 0 0 0.00
230 7000018796 200 200 100 20.EXTERNAL WATER SUPPLY 120002229 995424 18 18.33.1 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluicevalve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter and180 mm deep ( inside) with chained lid and RCC top slab1:2:4 mix (1cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete1:5:10 (1cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement:3coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design : With common burnt clayF.P.S.(non modular) bricks of class designation 7.5. EA 3.00 Included 0.00 0.00 0 0 0.00
231 7000018796 200 200 110 20.EXTERNAL WATER SUPPLY 120002150 995424 18 18.17.6 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm nominal bore EA 3.00 Included 0.00 0.00 0 0 0.00
232 7000018796 200 200 120 20.EXTERNAL WATER SUPPLY 120002309 995424 18 18.60.1 Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board completewith bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 80 mm dia nominal bore EA 1.00 Included 0.00 0.00 0 0 0.00
233 7000018796 200 200 130 20.EXTERNAL WATER SUPPLY 170003958 995421 18 Supplying and fixing of Tank inlet connection of cast iron body with gun metal male instantaneous inlet couplings completewith cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way - 100 mm dia M.S.Pipe EA 1.00 Included 0.00 0.00 0 0 0.00
234 7000018796 200 200 140 20.EXTERNAL WATER SUPPLY 120002138 995424 18 18.13.1 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, includingcutting and threading the pipe etc. complete : 25 to 40 mm nominal bore EA 1.00 Included 0.00 0.00 0 0 0.00
235 7000018796 200 200 150 20.EXTERNAL WATER SUPPLY 120002139 995424 18 18.13.2 Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, includingcutting and threading the pipe etc. complete : 50 to 80 mm nominal bore EA 1.00 Included 0.00 0.00 0 0 0.00
236 7000018796 200 200 160 20.EXTERNAL WATER SUPPLY 170003959 995421 18 Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings likeelbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frameand painting with two or more coats of synthetic enamel paint of required shade complete as required :(Sewerage Pumping line)100 mmdia M 80.00 Included 0.00 0.00 0 0 0.00
IRRIGATION SYSTEM
237 7000018796 210 210 10 21.IRRIGATION SYSTEM 120002113 995424 18 18.9.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. :External work : 20 mm nominal outer dia.Pipes. M 6.00 Included 0.00 0.00 0 0 0.00
238 7000018796 210 210 20 21.IRRIGATION SYSTEM 120002116 995424 18 18.9.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. :External work : 40 mm nominal outer dia.Pipes. M 200.00 Included 0.00 0.00 0 0 0.00
239 7000018796 210 210 30 21.IRRIGATION SYSTEM 120002255 995424 18 18.41.2 Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. : 20 mm diameterpipe M 3.00 Included 0.00 0.00 0 0 0.00
240 7000018796 210 210 40 21.IRRIGATION SYSTEM 120002258 995424 18 18.41.5 Providing and filling sand of grading zone V or coarser grade all- round the G.I. pipes in external work. : 40 mm diameterpipe M 200.00 Included 0.00 0.00 0 0 0.00
241 7000018796 210 210 50 21.IRRIGATION SYSTEM 120002228 995424 18 18.32.1 Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock,with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement :2 coarse sand :4graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement :5 fine sand:10 gradedstone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12mm thick finished withafloating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of classdesignation 7.5. EA 1.00 Included 0.00 0.00 0 0 0.00
242 7000018796 210 210 60 21.IRRIGATION SYSTEM 120002151 995424 18 18.18.1 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mmnominal bore EA 4.00 Included 0.00 0.00 0 0 0.00
SEWERAGE SYESTEM
243 7000018796 220 220 10 22.SEWERAGE SYESTEM 120000354 995433 18 2.10.1.2 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides,ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, inlayersnot exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplusexcavated soil as directed, within a lead of 50 m (All kinds of soil) : Pipes, cables etc. exceeding 80 mm dia. but not exceeding300 mm dia. M 20.00 Included 0.00 0.00 0 0 0.00
244 7000018796 220 220 20 22.SEWERAGE SYESTEM 120000356 995433 18 2.11. Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m.(Rate is over corresponding basic item for depth up to 1.5 M). M 1.00 Included 0.00 0.00 0 0 0.00
245 7000018796 220 220 30 22.SEWERAGE SYESTEM 120002653 995424 18 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cementmortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe M 20.00 Included 0.00 0.00 0 0 0.00
246 7000018796 220 220 40 22.SEWERAGE SYESTEM 120002630 995424 18 19.2.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)all-round S.W. pipes including bed concrete as per standard design: 150 mm diameter S.W. pipe M 20.00 Included 0.00 0.00 0 0 0.00
247 7000018796 220 220 50 22.SEWERAGE SYESTEM 120002665 995424 18 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finishedwith floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate20mm nominal size) finished with a floating coat of neat cement complete as per standard design (Inside size 90x80 cm and 45 cm deepincluding C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38kg(weight of cover 23 kg and weight of frame 15 kg) ) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 EA 2.00 Included 0.00 0.00 0 0 0.00
248 7000018796 220 220 60 22.SEWERAGE SYESTEM 120002671 995424 18 19.8.1.1 Extra for depth for manholes - Size 90x80 cm : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 M 1.00 Included 0.00 0.00 0 0 0.00
249 7000018796 220 220 70 22.SEWERAGE SYESTEM 120002675 995424 18 19.9.1.1 Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floatingcoat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size), andmaking necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finishedwith a floating coat of neat cement, all complete as per standard design - 0.91 m deep with S.F.R.C. cover and frame (heavy duty,HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than182kg., fixed in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering,shuttering all complete.(Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 EA 1.00 Included 0.00 0.00 0 0 0.00
250 7000018796 220 220 80 22.SEWERAGE SYESTEM 120002677 995424 18 19.10.1 Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91m to 1.67m : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 M 0.50 Included 0.00 0.00 0 0 0.00
251 7000018796 220 220 90 22.SEWERAGE SYESTEM 120002638 995424 18 19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with watertight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not lessthan 2.70 kg as per standard design (100x100 mm size P type ) : With common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 EA 1.00 Included 0.00 0.00 0 0 0.00
252 7000018796 220 220 100 22.SEWERAGE SYESTEM 120002689 995424 18 19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel barconforming to IS: 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequateanchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemicalresistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing,including fixing in manholes with30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mmnominal size) complete as per design. EA 10.00 Included 0.00 0.00 0 0 0.00
253 7000018796 220 220 110 22.SEWERAGE SYESTEM 120002704 995424 18 19.21.2 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floorswith cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on bothsides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channelsfor the drain etc. complete : For pipes 250 to 300 mm diameter EA 1.00 Included 0.00 0.00 0 0 0.00
EXTERNAL DRAINAGE SYSTEM
254 7000018796 230 230 10 23.EXTERNAL DRAINAGE SYSTEM 120000354 995433 18 2.10.1.2 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides,ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, inlayersnot exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplusexcavated soil as directed, within a lead of 50 m (All kinds of soil) : Pipes, cables etc. exceeding 80 mm dia. but not exceeding300 mm dia. M 140.00 Included 0.00 0.00 0 0 0.00
255 7000018796 230 230 20 23.EXTERNAL DRAINAGE SYSTEM 120000356 995433 18 2.11. Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m.(Rate is over corresponding basic item for depth up to 1.5 M). M 2.00 Included 0.00 0.00 0 0 0.00
256 7000018796 230 230 30 23.EXTERNAL DRAINAGE SYSTEM 120002654 995424 18 19.6.3 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cementmortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. pipe M 140.00 Included 0.00 0.00 0 0 0.00
257 7000018796 230 230 40 23.EXTERNAL DRAINAGE SYSTEM 120002655 995424 18 19.6.4 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cementmortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe M 10.00 Included 0.00 0.00 0 0 0.00
258 7000018796 230 230 50 23.EXTERNAL DRAINAGE SYSTEM 120002636 995424 18 19.3.4 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up tohaunches of S.W. pipes including bed concrete as per standard design : 250 mm diameter S.W. pipe M 140.00 Included 0.00 0.00 0 0 0.00
259 7000018796 230 230 60 23.EXTERNAL DRAINAGE SYSTEM 120002637 995424 18 19.3.5 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up tohaunches of S.W. pipes including bed concrete as per standard design : 300 mm diameter S.W. pipe M 10.00 Included 0.00 0.00 0 0 0.00
260 7000018796 230 230 70 23.EXTERNAL DRAINAGE SYSTEM 120002665 995424 18 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1cement : 2coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8graded stone aggregate 40mm nominal size), inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finishedwith floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate20mm nominal size) finished with a floating coat of neat cement complete as per standard design (Inside size 90x80 cm and 45 cm deepincluding C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38kg(weight of cover 23 kg and weight of frame 15 kg) ) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 EA 2.00 Included 0.00 0.00 0 0 0.00
261 7000018796 230 230 80 23.EXTERNAL DRAINAGE SYSTEM 120002671 995424 18 19.8.1.1 Extra for depth for manholes - Size 90x80 cm : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 M 1.00 Included 0.00 0.00 0 0 0.00
262 7000018796 230 230 90 23.EXTERNAL DRAINAGE SYSTEM 120002675 995424 18 19.9.1.1 Constructing brick masonry circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floatingcoat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size), andmaking necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finishedwith a floating coat of neat cement, all complete as per standard design - 0.91 m deep with S.F.R.C. cover and frame (heavy duty,HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than182kg., fixed in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering,shuttering all complete.(Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 EA 1.00 Included 0.00 0.00 0 0 0.00
263 7000018796 230 230 100 23.EXTERNAL DRAINAGE SYSTEM 120002677 995424 18 19.10.1 Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91m to 1.67m : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 M 1.00 Included 0.00 0.00 0 0 0.00
264 7000018796 230 230 110 23.EXTERNAL DRAINAGE SYSTEM 120002722 995424 18 19.27.1 Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand)including500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 EA 14.00 Included 0.00 0.00 0 0 0.00
265 7000018796 230 230 120 23.EXTERNAL DRAINAGE SYSTEM 120002723 995424 18 19.28.1 Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand )with pre-cast R.C.C. vertical grating complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 EA 1.00 Included 0.00 0.00 0 0 0.00
266 7000018796 230 230 130 23.EXTERNAL DRAINAGE SYSTEM 120002689 995424 18 19.16 Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel barconforming to IS: 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequateanchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemicalresistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing,including fixing in manholes with30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand :6 graded stone aggregate 20 mmnominal size) complete as per design. EA 25.00 Included 0.00 0.00 0 0 0.00
267 7000018796 230 230 140 23.EXTERNAL DRAINAGE SYSTEM 120002704 995424 18 19.21.2 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floorswith cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on bothsides with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channelsfor the drain etc. complete : For pipes 250 to 300 mm diameter EA 4.00 Included 0.00 0.00 0 0 0.00
WATER SUPPLY &TREATMENT
268 7000018796 240 240 10 24.WATER SUPPLY &TREATMENT 170003960 995421 18 Supply Installation testing and commissioning of Vertical/horizontal monoblock centrifugal transfer pumping set with SS-316 bodyand SS-316 impeller, SS-316 shaft mechanical seal, connected to a TEFC induction motor suitable for 415 volts ± 3% phase 50 cyclesAC supply with a common suction header with valves on main connecting & pumps inlet and a common delivery header with valves,strainer, includingt water shock absorber, non return valves with MS galvanized supports and painting with one coat of primer andtwo coats of synthetic enamel paint including a 100mm dia pressure gauge, Vibration eliminating pads under foundation, all mountedon a common base plate of MS 80x40mm I section bolted to RCC foundation, including elctrical control panel , Auto levelcontroller, cable panel to pumps complete in all respects. FOR FILTER FEED PUMP No. of Pumps: 2 (1 Working + 1 Stand by ) Capacity : 120 LPM Head : 35m SET 1.00 Included 0.00 0.00 0 0 0.00
269 7000018796 240 240 20 24.WATER SUPPLY &TREATMENT 170003961 995421 18 Water Supply Pump (Hydropneumatic System With variable Speed System) Supply of packaged variable skid mounted hydropneumatic systemcomprising of :- a) Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304impellers with stainless steel SS-431 shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected toTEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. b) Pressure vessel of noncorrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fullyreplaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000cycles. No. and capacity of Pressure Vessel – 01 Nos. x 60 Ltrs c) Control Panel with programmable logic controller (PLC) forcyclic operation of pumps. Pump working sequence should change after every operation.Contractor overload relays and MCBs shouldconfirm to IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply should beprovided in the panel along with the ammeter & voltmeter. Control panel should also consist of cooling fan. d) Pressure switchesbellow type fitted with micro switch and having maximum pressure and differential scale should confirming BS-6134 standardsand IP55 protection class. e) Stainless steel suction and delevery header, ball valve on each pump on section delivery side, nonreturn valves, Y stainer complete in all respect. f) Ball valves to be used should be Hot Pressed brass OT-58 with stainless steelball and P.T.F.E seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement. g) Complete set system tobe mounted on a common base frame and shall follow following duty. Set of accessories such as pressure switches, pressuretransducers, inter connecting power and control cabling etc. complete Accessories like pressure gauge, MS base frame (Syntheticenamel painted over a coat of primer)G.I suction and delivery header with flanges for inlet connection, common outlet header withflanges for outlet connections as required, and inter connecting piping with NRV/VALVE/STRAINER, reducer type etc. all necessaryindigenous accessories as required to complete the installation.DOMESTIC WATER TRANSFER PUMPS (HPN)(OVER HEAD TANK FILLING) No. ofPumps: 2 (1 Working + 1 Stand by ) Capacity : 130 LPM Head : 60 m SET 1.00 Included 0.00 0.00 0 0 0.00
270 7000018796 240 240 30 24.WATER SUPPLY &TREATMENT 170003962 995421 18 Water Supply Pump (Hydropneumatic System With variable Speed System) Supply of packaged variable skid mounted hydropneumatic systemcomprising of :- a) Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304impellers with stainless steel SS-431 shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected toTEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. b) Pressure vessel of noncorrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fullyreplaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000cycles. No. and capacity of Pressure Vessel – 01 Nos. x 60 Ltrs c) Control Panel with programmable logic controller (PLC) forcyclic operation of pumps. Pump working sequence should change after every operation.Contractor overload relays and MCBs shouldconfirm to IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply should beprovided in the panel along with the ammeter & voltmeter. Control panel should also consist of cooling fan. d) Pressure switchesbellow type fitted with micro switch and having maximum pressure and differential scale should confirming BS-6134 standardsand IP55 protection class. e) Stainless steel suction and delevery header, ball valve on each pump on section delivery side, nonreturn valves, Y stainer complete in all respect. f) Ball valves to be used should be Hot Pressed brass OT-58 with stainless steelball and P.T.F.E seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement. g) Complete set system tobe mounted on a common base frame and shall follow following duty. Set of accessories such as pressure switches, pressuretransducers, inter connecting power and control cabling etc. complete Accessories like pressure gauge, MS base frame (Syntheticenamel painted over a coat of primer)G.I suction and delivery header with flanges for inlet connection, common outlet header withflanges for outlet connections as required, and inter connecting piping with NRV/VALVE/STRAINER, reducer type etc. all necessaryindigenous accessories as required to complete the installation.DOMESTIC WATER TRANSFER PUMPS (HPN)(TERRACE PUMP FOR TOILET SUPPLY)No. of Pumps: 2 (1 Working + 1 Stand by )Capacity : 100 LPM Head : 30 M SET 1.00 Included 0.00 0.00 0 0 0.00
271 7000018796 240 240 40 24.WATER SUPPLY &TREATMENT 170003963 995421 18 Water Supply Pump (Hydropneumatic System With variable Speed System) Supply of packaged variable skid mounted hydropneumatic systemcomprising of :- a) Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304impellers with stainless steel SS-431 shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected toTEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. b) Pressure vessel of noncorrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fullyreplaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000cycles. No. and capacity of Pressure Vessel – 01 Nos. x 60 Ltrs c) Control Panel with programmable logic controller (PLC) forcyclic operation of pumps. Pump working sequence should change after every operation.Contractor overload relays and MCBs shouldconfirm to IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply should beprovided in the panel along with the ammeter & voltmeter. Control panel should also consist of cooling fan. d) Pressure switchesbellow type fitted with micro switch and having maximum pressure and differential scale should confirming BS-6134 standardsand IP55 protection class. e) Stainless steel suction and delevery header, ball valve on each pump on section delivery side, nonreturn valves, Y stainer complete in all respect. f) Ball valves to be used should be Hot Pressed brass OT-58 with stainless steelball and P.T.F.E seal and O-Ring. NRVs to be used should be with Springs and O-Ring arrangement. g) Complete set system tobe mounted on a common base frame and shall follow following duty. Set of accessories such as pressure switches, pressuretransducers, inter connecting power and control cabling etc. complete Accessories like pressure gauge, MS base frame (Syntheticenamel painted over a coat of primer)G.I suction and delivery header with flanges for inlet connection, common outlet header withflanges for outlet connections as required, and inter connecting piping with NRV/VALVE/STRAINER, reducer type etc. all necessaryindigenous accessories as required to complete the installationFLUSHING WATER TRANSFER PUMPS (HPN)(TERRACE PUMP FOR TOILET SUPPLY)No. of Pumps: 2 (1 Working + 1 Stand by ) Capacity : 150 LPM Head 30 m SET 1.00 Included 0.00 0.00 0 0 0.00
272 7000018796 240 240 50 24.WATER SUPPLY &TREATMENT 170003964 995421 18 Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersiblemotor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facilitywith one proper working at low level & two proper working at high level with an audible alarm including all interconnectivitycables, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in allrespect (one working + one standby/both working in high flow conditions) PUMP ROOM SUMP PUMP (Solid handiling capacity 10-12mm)Capacity- 150 lpm (Each) Head - 15 m SET 1.00 Included 0.00 0.00 0 0 0.00
273 7000018796 240 240 60 24.WATER SUPPLY &TREATMENT 170003965 995421 18 Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersiblemotor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facilitywith one proper working at low level & two proper working at high level with an audible alarm including all interconnectivitycables, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in allrespect (one working + one standby/both working in high flow conditions) SEWERAGE SUMP PUMP (Basement) (Solid handiling capacity35-50mm) Capacity- 70 lpm (Each) Head - 15 m SET 1.00 Included 0.00 0.00 0 0 0.00
274 7000018796 240 240 70 24.WATER SUPPLY &TREATMENT 170003966 995421 18 Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersiblemotor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facilitywith one proper working at low level & two proper working at high level with an audible alarm including all interconnectivitycables, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in allrespect (one working + one standby/both working in high flow conditions) SEWERAGE SUMP PUMP(External) (Solid handiling capacity35-50mm) Capacity- 160 lpm (Each) Head - 25 m SET 1.00 Included 0.00 0.00 0 0 0.00
275 7000018796 240 240 80 24.WATER SUPPLY &TREATMENT 170003967 995421 18 Pressure Filter (Domestic Water) Providing, fixing, testing & commissioning of vertical FRP filter with adequate dirt holdingcapacity. The filter shall be complete having PVC frontal piping with 50 mm multiport valve including all supporting structure withinitial charge filter media. The filter shall be provided with set of internals for raw water inlet and bottom collecting system.Velocity in frontal piping and valves shall be 1.50 m/sec. The working pressure shall be 3.5Kg/Sq.cm and the filter shall be testedfor 6Kg/Sq.cm. (Make - Pentair/any Reputed make) Discharge : 120 LPM per filter Filtration Rate :15000 lit./m2/h EA 1.00 Included 0.00 0.00 0 0 0.00
276 7000018796 240 240 90 24.WATER SUPPLY &TREATMENT 170003968 995421 18 Activated Carbon Filter providing, fixing, testing and commissioning of vertical self supporting FRP Activated Carbon Filter.Activated Carbon Filter shall be constructed of FRP/composit material with inner shell of integrated Polyethylene with FiberReinforced Plastic as per manufacturer standard. The inner distribution system and the under bed draw off system shall be of Hub &Lateral type/Riser tube with top & bottom strainers of Polypropylene material. Filter shall be supplied with initial charge withsupporting media like silex, gravel etc. The filter shall be complete with pressure gauge at inlet & outlet, sample cock, PVC facepiping/interconnected piping, Multiport valve and all necessary accessories. Flow Rate : 120 LPM Filtration Rate : 15000 lit./m2/hMax. operating pressure: 3.5 kg/sq.cm Test pressure: 5.5 kg/sq.cm EA 1.00 Included 0.00 0.00 0 0 0.00
277 7000018796 240 240 100 24.WATER SUPPLY &TREATMENT 170003969 995421 18 Water Softener Providing, fixing, testing &commissioning of FRP water softening plant (suitable for 3 Kg/Sqcm working pressure)complete with initial charge with T-40 NA Resin, multiport valve with built in ejector for controlling all operations), regenerationsystem and HDPE tank, pressure gauge at inlet, outlet and back wash (each with isolation cock), valves, fittings and water hardnesstesting kit & associated works. Velocity in frontal piping and valves shall be 1.50 m/sec Softener shall be suitable for thefollowing duty: (Make- Pentair/any reputed make) Minimum expected rate of flow: 120 LPM Expected raw water hardness : app.150-250 ppm Expected treated water hardness: less than 100 ppm Max. working pressure : 4 kg/cm2 EA 1.00 Included 0.00 0.00 0 0 0.00
278 7000018796 240 240 110 24.WATER SUPPLY &TREATMENT 170003970 995421 18 POST CHLORINATION OF WATER Supply Installation testing and commissioning of On line electronic chemical solution dosing systemcomprising of electronic metering pump (with both frequency and stroke length controls to control the dosage rate between 10-100 %of rated maximum capacity), virgin HDPE chemical grade solution tank of rquired capacity, necessary injection fitting assembly, footvalve cum strainer and suction and delivery tubing etc. upto the point of injection complete in all respects as required ForCholorination of filtered water Dosing capacity : 0-6 ltrs. per hour, Dosing Head : 3.5 kg/cm2 EA 1.00 Included 0.00 0.00 0 0 0.00
279 7000018796 240 240 120 24.WATER SUPPLY &TREATMENT 120002102 995424 18 18.7.1 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 15 mm nominal outer dia .Pipes. M 5.00 Included 0.00 0.00 0 0 0.00
280 7000018796 240 240 130 24.WATER SUPPLY &TREATMENT 120002103 995424 18 18.7.2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 20 mm nominal outer dia .Pipes. M 2.00 Included 0.00 0.00 0 0 0.00
281 7000018796 240 240 140 24.WATER SUPPLY &TREATMENT 120002104 995424 18 18.7.3 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 25 mm nominal outer dia .Pipes. M 2.00 Included 0.00 0.00 0 0 0.00
282 7000018796 240 240 150 24.WATER SUPPLY &TREATMENT 120002105 995424 18 18.7.4 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 32 mm nominal outer dia .Pipes. M 5.00 Included 0.00 0.00 0 0 0.00
283 7000018796 240 240 160 24.WATER SUPPLY &TREATMENT 120002106 995424 18 18.7.5 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 40 mm nominal outer dia .Pipes. M 10.00 Included 0.00 0.00 0 0 0.00
284 7000018796 240 240 170 24.WATER SUPPLY &TREATMENT 120002107 995424 18 18.7.6 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supplyincluding all CPVC plain & brass threaded fittings including fixing the pipe with clamps at1.00 m spacing. This includes jointing ofpipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. :Internalwork - Exposed on wall : 50 mm nominal outer dia .Pipes. M 15.00 Included 0.00 0.00 0 0 0.00
285 7000018796 240 240 180 24.WATER SUPPLY &TREATMENT 120002147 995424 18 18.17.3 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore EA 2.00 Included 0.00 0.00 0 0 0.00
286 7000018796 240 240 190 24.WATER SUPPLY &TREATMENT 120002148 995424 18 18.17.4 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore EA 4.00 Included 0.00 0.00 0 0 0.00
287 7000018796 240 240 200 24.WATER SUPPLY &TREATMENT 120002149 995424 18 18.17.5 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore EA 2.00 Included 0.00 0.00 0 0 0.00
288 7000018796 240 240 210 24.WATER SUPPLY &TREATMENT 170003959 995421 18 Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings likeelbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frameand painting with two or more coats of synthetic enamel paint of required shade complete as required :(Sewerage Pumping line)100 mmdia M 10.00 Included 0.00 0.00 0 0 0.00
289 7000018796 240 240 220 24.WATER SUPPLY &TREATMENT 170003971 995421 18 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including allCPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching,refilling & testing of joints complete as per direction of Engineer in Charge. External Work 100 mm dia M 8.00 Included 0.00 0.00 0 0 0.00
290 7000018796 240 240 230 24.WATER SUPPLY &TREATMENT 170003972 995421 18 Control system To switch on the pumps (including Raw Water Pump, Domestic water supply pump etc.) when the level of water in thesupply water tank is low and to cut off the pump when the level in the receiving water tank is high and switch off the pumpswhen the level of water in the supply water tank is low.To indicate 5 levels of water in all tanks through a control panel with LEDsTo start the pumps in a cyclic order. The system shall be complete to ensure automatic quotation of pump in accordance to waterlevel in respective tanks. The Contractor will include all the under ground and over head tanks and all the pumps as required forlevel control in this item SET 1.00 Included 0.00 0.00 0 0 0.00
291 7000018796 250 250 10 25.BIM MODELLING 170003973 998338 18 To prepare 3D Building Information Model (BIM) of areas Based on final/GFC Structural and Architectural 2D design drawings .Bidder have to submit BIM model Minimum LOD 300.To coordinate the final Architectural and Structural and to provide the conflicts,if any, for design/ drawing rectification.Generate schedules and quantity take-off of major civil items from the 3D BIM model. LOT 1.00 Included 0.00 0.00 0 0 0.00
292 7000018796 260 10 10 EMI TESTING 170003974 998338 18 Detail Study of EMI/EMF/ EMC For DC Building as per Technical Specifications LOT 1.00 Included 0.00 0.00 0 0 0.00
TIER CERTIFICATION
293 7000018796 270 20 10 TIER CERTIFICATION 170003975 998338 18 Tier-III Certification of Design Documents/drawing from Uptime Institute as per Technical specificiations LOT 1.00 Included 0.00 0.00 0 0 0.00
Total Price 0.00 0.00 0 0.00
# In case the bidder leaves the cell for confirmation of the SAC and/or GST rate “blank”, the SAC and corresponding GST rate indicated by the Employer shall be deemed to be the one confirmed by the Bidder.
Place : Printed Name :
5002002317/OTHERS/DOM/A06-CC CS -7 Schedule - 1 Direct Total #REF! Sole Bidder `
BO Total #REF! 0
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
(SCHEDULE OF RATES AND PRICES)
Bidder’s Name and Address (Sole Bidder) : To:
Contract Services
Name : Power Grid Corporation of India Ltd., , &
Address : "Saudamini", Plot No.-2
Gurgaon (Haryana) - 122001
Price Break-up for individual items Direct
All Prices are in Indian Rupees. Bought-Out
SI. No. Item Description Unit Qty. (for all locations) Unit Rate Total Price 0
1 Construction of Data Centre Building at Manesar Nos. 0
a) 2.6.1 earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m inwidth as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50m and lift up to 1.5m,disposed earth to belevelled and neatly dressed. / All kinds of soil Meter 15440 0.00 Included 0
1.2 2.26.1 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. /All kinds ofsoil. Meter 24008 0.00 Included 0
1.3 5.9.5 Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders,bressumers and cantilevers. Cu.M 11406 0.00 Included 0
1.4 5.9.6 Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Postsand Struts. Cu.M 4422 0.00 Included 0
1.5 5.9.7 Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) exceptspiral-staircases. Sq.M. 278 0.00 Included 0
1.6 5.9.19 Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc.,including edges. MT 76 0.00 Included 0
1.7 5.11.1 Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including costof de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Planarea to be measured) Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). Cu.M. 12263 0.00 Included 0
1.8 5.33.1.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concretework; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures inrecommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability andworkability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payableseparately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shallhave discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M25 gradewith minimum cement content of 330 kg /cum" Cu.M. 86 0.00 Included 0
1.9 5.33.1.2 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concretework; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability andworkability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payableseparately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shallhave discretion to either re-design the mix or bear the cost of extra cement. All works upto plinth level. Concrete of M30 gradewith minimum cement content of 350 kg /cum" Nos. 6719 0.00 Included 0
1.10 5.33.2.1 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concretework; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures inrecommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability andworkability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payableseparately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shallhave discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level up to floor V level.Concrete of M25 grade with minimum cement content of 330 kg /cum" MT 36 0.00 Included 0
1.11 #REF! No. #REF! #REF! #REF! #REF!
2 #REF! Nos. #REF! #REF! #REF!
a) #REF! Meter #REF! #REF! #REF! #REF!
2.2 #REF! Meter #REF! #REF! #REF! #REF!
2.3 #REF! Cu.M #REF! #REF! #REF! #REF!
2.4 #REF! Cu.M #REF! #REF! #REF! #REF!
2.5 #REF! Sq.M. #REF! #REF! #REF! #REF!
2.6 #REF! MT #REF! #REF! #REF! #REF!
2.7 #REF! Cu.M. #REF! #REF! #REF! #REF!
2.8 #REF! Cu.M. #REF! #REF! #REF! #REF!
2.9 #REF! Nos. #REF! #REF! #REF! #REF!
2.10 #REF! MT #REF! #REF! #REF! #REF!
2.11 #REF! No. #REF! #REF! #REF! #REF!
Total Price #REF!
Place : Printed Name :
5002002317/OTHERS/DOM/A06-CC CS -7 Schedule - 2
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
(SUMMARY OF TAXES & DUTIES)
Bidder’s Name and Address (Sole Bidder) : To:
Contract Services
Name : Power Grid Corporation of India Ltd.,
Address : "Saudamini", Plot No.-2
Gurgaon (Haryana) - 122001
Sl. No. Item Nos. Total Price (INR) After Discount After MPDiscount
1 TOTAL GST ON SERVICES Excise Duty #REF! Excise Duty #REF!
Total GST on Services (indentified in Schedule-1) which are not included in the prices as per the provision of the Bidding Documents, as applicable 0.00
GRAND TOTAL 0.00
Date : -- Printed Name :
Place : Designation :
5002002317/OTHERS/DOM/A06-CC CS -7 Schedule - 5
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
SUMMARY OF TAXES & DUTIES APPLICABLE ON GOODS
Bidder’s Name and Address (Sole Bidder) : To:
Contract Services
Name : Power Grid Corporation of India Ltd.,
Address : "Saudamini", Plot No.-2
Gurgaon (Haryana) - 122001
Sl. No. Item Nos. Total Price (INR) After Discount After MPDiscount
1 TOTAL EXCISE DUTY #REF! Excise Duty #REF! Excise Duty #REF!
Total Excise Duty for direct transaction between the Contractor and the Employer (identified in Schedule 1 as 'Direct') which are not included in the Ex-works price as per the provision of the Bidding Documents, as applicable.
Rate of Excise Duty for Direct items indicated in Sch-1 #REF!
2 TOTAL SALES TAX #REF! Sales Tax 0.00 Sales Tax 0.00
Total Sales Tax for direct transaction between the Contractor and the Employer (identified in Schedule 1 as 'Direct') which are not included in the Ex-works price as per the provision of the Bidding Documents, as applicable. #REF! 0 #REF! 0
Amount on which Sales Tax is applicable [only ex-w price] #REF! Amount #REF! Amount #REF!
#REF! #REF! ED #REF! ED #REF!
Rate of Sales Tax #REF!
3 TOTAL VAT #REF! Vat 0 Vat 0
Total VAT for direct transaction between the Contractor and the Employer (identified in Schedule 1 as 'Direct') which are not included in the Ex-works price as per the provision of the Bidding Documents, as applicable #REF! 0 #REF! 0
Amount on which VAT is applicable [only ex-w price] #REF! Amount #REF! Amount #REF!
#REF! #REF! ED #REF! ED #REF!
Rate of VAT #REF!
4 TOTAL OCTROI #REF!
Total Octroi as applicable for destination site/state on all items of supply, as per the provisions of the Bidding Documents, on all items of Schedule 1.
Amount on which Octroi is applicable Click here for details of Octroi
5 TOTAL ENTRY TAX #REF!
Total Entry Tax as applicable for destination site/state on all items of supply, as per the provisions of the Bidding Documents, on all items of Schedule 1.
Amount on which Entry Tax is applicable Click here for details of Entry Taxes
6 TOTAL OTHER TAXES & DUTIES #REF!
Total Others levies payable in India (please specify) as applicable for destination site/state on all items of supply, as per the provisions of the Bidding Documents, on all items of Schedule 1.
Amount on which Other Taxes & Duties are applicable Click here for details of Other Taxes & Duties
GRAND TOTAL [1+2+3] #REF! Grand Total after Discount #REF! Grand Total after MPD #REF!
Above Grand Total does not include Octroi, Entry Tax , Other Taxes & Duties quoted by bidder at Sl. No. 4,5 & 6 above Plus Octroi, Entry Tax , Other Taxes & Duties quoted by bidder at Sl. No. 4,5 & 6 above
Note : The reimbursement of Excise Duty, Sales Tax/VAT and other levies as per Sl. No. 1, 2 & 3 above subject to provision of ITB Clause 11.4 shall be only against those items for which the Mode of Transaction indicated in Schedule - 1 is 'Direct'. In case of those items in the said Sechedule-1 against which the mode of transaction has been left blank, the same shall be deemed to be 'Bought-out' for the purpose of Evaluation and award of Contract and the price indicated in Schedule 1 against such items shall be deemed to be inclusive of all such taxes, duties and levies.
Date : -- Printed Name :
Place : Designation :
5002002317/OTHERS/DOM/A06-CC CS -7 Schedule -3
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
(GRAND SUMMARY )
Bidder’s Name and Address (Sole Bidder) : To:
Contract Services
Name : Power Grid Corporation of India Ltd.,
Address : "Saudamini", Plot No.-2
Gurgaon (Haryana) - 122001
Sl. No. Description Total Price (INR)
1 TOTAL SCHEDULE NO. 1 0.00
2 TOTAL SCHEDULE NO. 2 (Taxes and Duties) 0.00
Total Price [1+2] 0.00
2 TOTAL SCHEDULE NO. 2 #REF!
Local Transportation, Insurance and other Incidental Services
3 TOTAL SCHEDULE NO. 3 #REF!
Installation Charges
4 TOTAL SCHEDULE NO. 4 Not Applicable
Training Charges
5 TOTAL SCHEDULE NO. 5 #REF!
Taxes and Duties Plus Octroi, Entry Tax , Other Taxes & Duties quoted by bidder at Sl. No. 4,5 & 6 of Sch-5
6 TOTAL SCHEDULE NO. 7 #REF!
Type Test Charges [Total of this Schedule is included in Schedule - 1 above.]
GRAND TOTAL [1+2+3+4+5] 0.00
Plus Octroi, Entry Tax , Other Taxes & Duties quoted by bidder at Sl. No. 4,5 & 6 of Sch-5
Date : -- Printed Name :
Place : Designation :
5002002317/OTHERS/DOM/A06-CC CS -7 Schedule - 3 After Discount
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
(GRAND SUMMARY : AFTER DISCOUNT)
Bidder’s Name and Address (Sole Bidder) : To:
Contract Services
Name : Power Grid Corporation of India Ltd.,
Address : "Saudamini", Plot No.-2
Gurgaon (Haryana) - 122001
Sl. No. Description Total Price (INR)
1 TOTAL SCHEDULE NO. 1 0.00
2 TOTAL SCHEDULE NO. 2 (Taxes and Duties) 0.00
Total Price [1+2] 0.00
2 TOTAL SCHEDULE NO. 2 #REF!
Local Transportation, Insurance and other Incidental Services
3 TOTAL SCHEDULE NO. 3 #REF!
Installation Charges
4 TOTAL SCHEDULE NO. 4 Not Applicable
Training Charges
5 TOTAL SCHEDULE NO. 5 #REF!
Taxes and Duties Plus Octroi, Entry Tax , Other Taxes & Duties quoted by bidder at Sl. No. 4,5 & 6 of Sch-5
6 TOTAL SCHEDULE NO. 7 #REF!
Type Test Charges [Total of this Schedule is included in Schedule - 1 above.]
GRAND TOTAL [1+2+3+4+5] #REF!
Plus Octroi, Entry Tax , Other Taxes & Duties quoted by bidder at Sl. No. 4,5 & 6 of Sch-5
Date : -- Printed Name :
Place : Designation :
This letter of discount is optional. Bidder may / may not offer any discount.
5002002317/OTHERS/DOM/A06-CC CS -7 Letter of Discount
LETTER OF DISCOUNT
Contract Services
Power Grid Corporation of India Ltd.,
"Saudamini", Plot No.-2
Sector-29, (near IFFCO Chowk)
Gurgaon (Haryana) - 122001
Subject : Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation
With reference to the subject tender, we hereby offer unconditional discount on the prices quoted by us as per details given here below : Eq Weightage of Rs/ % Final Discount Factor
1 Discount on lum-sum basis on total price quoted by us. In Rs. 0.00 0.0000000000% 0.0000000000%
2 Discount on percent basis on total price quoted by us . In Percent (%) 0.00 0.00%
3 Discount on lum-sum basis on the Schedules as given below : [The discount shall be proportionately applicable on all the relevent items of the respective Schdules.] In Rs.
Schedule-1 : Ex works prices (Direct Only) In Rs. 0.00 0.0000000000% Schedule-1 : (Direct Only) #REF!
Schedule-1 : Ex works prices (Bought Out Only) In Rs. #REF! #REF! Schedule-1 : (Bought Out Only) #REF!
Schedule-2 : Freight & Insurance In Rs. #REF! #REF! Schedule-2 : Freight & Insurance #REF!
Schedule-3 : Erection Charges In Rs. #REF! #REF! Schedule-3 : Erection Charges #REF!
Schedule-7 : Type Test Charges In Rs. #REF! #REF! Schedule-6 : Type Test Charges #REF!
4 Discount on percent basis on the Schedules as given below : [The discount shall be proportionately applicable on all the relevent items of the respective Schdules.] In Percent (%)
Schedule-1 : Ex works prices (Direct Only) In Percent (%) 0.00 0.00%
Schedule-1 : Ex works prices (Bought Out Only) In Percent (%) #REF! 0.00%
Schedule-2 : Freight & Insurance In Percent (%) #REF! 0.00%
Schedule-3 : Erection Charges In Percent (%) #REF! 0.00%
Schedule-7 : Type Test Charges In Percent (%) #REF! 0.00%
5 Multipackage discount applicable on this package (TW04) only if other packages covered under the same bidding document is also awarded to us. Discount on lum-sum basis on total price quoted by us without Taxes & Duties. [This discount shall be proportionately applicable on all the items of all the Schdules i.e. Sch-1 (without type test charges), Sch-2, Sch-3 & Sch-7] IN Rs. #REF! #REF!
3 Multipackage discount applicable on this package (TW04) only if other packages covered under the same bidding document is also awarded to us. Discount on percent basis on total price quoted by us without Taxes & Duties. [This discount shall be proportionately applicable on all the items of all the Schdules i.e. Sch-1 (without type test charges), Sch-2, Sch-3 & Sch-7] In Percent (%) #REF! 0.00%
Discount(s) offered at sl. No. 1 to 2 will automatically get displayed and accounted for in the respective items of the Schedules.
Please consider this letter of discount as the integral part of our price bid.
Thanking you, we remain,
Yours faithfully,
For and on behalf of
Date : -- Printed Name :
Place : Designation :
Details of Octroi
Sl No. Description of Items Amount on which Octroi is applicable Rate of Octroi Octroi
Details of Entry Tax
Sl No. Description of Items Amount on which Entry Tax is applicable Rate of Entry Tax Entry Tax
Details of Other Taxes & Duties
Sl No. Description of Items Amount on which Other Taxes & Duties are applicable Description of Taxes & Duties Rate of Taxes & Duties Amount of Taxes & Duties
5002002317/OTHERS/DOM/A06-CC CS -7 Bid Form 2nd Envelope Sole Bidder 1 st 1 January
0 2 nd 2 February
BID FORM (Second Envelope) 3 rd 3 March
Bid Proposal Ref. No. 5 th 5 May
Date : -- 6 th #VALUE! 6 June
7 th #VALUE! 7 July
To: 8 th #VALUE! 8 August
Contract Services 9 th #VALUE! 9 September
Power Grid Corporation of India Ltd., 10 th 10 October
"Saudamini", Plot No.-2 11 th 11 November
Sector-29, 12 th 12 December
Gurgaon (Haryana) - 122001 13 th
Name of Contract : Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation 15 th
Dear Ladies and/or Gentlemen, 16 th
Schedule 1 Price Components (Price Break-up) 21 st
Schedule 2 Taxes and duties not included in Schdule 1
Schedule 3 Grand Summary 26 th
2.5 We declare that items left blank in the Schedules will be deemed to have been included in other items. The TOTAL for each Schedule and the TOTAL of Grand Summary shall be deemed to be the total price for executing the Facilities and sections thereof in complete accordance with the Contract, whether or not each individual item has been priced. 31 st
3.0 We confirm that except as otherwise specifically provided our Bid Prices in this Second Envelope include all taxes, duties, levies and charges as may be assessed on us, our Sub-Contractor/Sub-Vendor or their employees by all municipal, state or national government authorities in connection with the Facilities, in and outside of India.
3.1 100% of applicable Taxes and Duties i.e GST , which are payable by the Employer under the Contract, shall be reimbursed by the Employer on production of satisfactory documentary evidence by the Contractor in accordance with the provisions of the Bidding Documents.
4.0 # (For Joint Venture only) We, the partners of Joint Venture submitting this bid, do agree and confirm that in case of Award of Contract on the Joint Venture, we shall be jointly and severally liable and responsible for the execution of the Contract in accordance with Contract terms and conditions.
5.0 We, hereby, declare that only the persons or firms interested in this proposal as principals are named here and that no other persons or firms other than those mentioned herein have any interest in this proposal or in the Contract to be entered into, if the award is made on us, that this proposal is made without any connection with any other person, firm or party likewise submitting a proposal is in all respects for and in good faith, without collusion or fraud.
Thanking you, we remain,
Yours faithfully,
For and on behalf of
Date : -- Printed Name :
Place : Designation :
Please provide additional information of the Bidder
Business Address :
Country of Incorporation :
State/Province to be indicated :
Name of Principal Officer :
Address of Principal Officer :
STATEMENT OF QUOTED / CORRECTED PRICES
All Figures are in Rupees
Sl. No. Price Component Quoted Price Corrected Price
1 TOTAL SCHEDULE NO. 1:Ex-Works Price of Plant and Equipment including Type Test Charges 0.00 0.00
2 TOTAL SCHEDULE NO.2: Local Transportation, Insurance and other Incidental Services. #REF! #REF!
3 TOTAL SCHEDULE NO.3: Installation Charges #REF! #REF!
4 TOTAL SCHEDULE NO.4: Training Charges Not Applicable Not Applicable
5 TOTAL BID PRICE: (Excluding Taxes & Duties) #REF! #REF!
6 DISCOUNT #REF! #REF!
7 NET BID PRICE (Excluding Taxes & Duties) #REF! #REF!
8 TAXES & DUTIES PAYABLE ADDITIONALLY
A) EXCISE DUTY #REF! 0.00
B) CENTRAL SALES TAX /VAT #REF! #REF!
C) ENTRY TAX / OCTROI #REF! #REF!
D) OTHERS #REF! 0.00
E) TOTAL TAXES & DUTIES #REF! #REF!
8 TOTAL BID PRICE (INCLUDING TAXES & DUTIES) #REF! #REF!
9 TOTAL SCHEDULE NO.7: Type Test Charges [Total of this Schedule is included in Schedule-1 above] #REF! #REF!
I) Bidder has indicated the following taxes and duties additionally applicable for their bid:
a) Excise Duty Rs. #REF!
b) CST /VAT Rs. #REF!
c) Entry Tax / Octroi Rs. #REF!
d) Others Rs. #REF!
II) Bidder has offered following discount(s)
III) With regard to Entry Tax, it may be mentioned that the substations covered under the subject pacakge falls in State of MP, where an entry tax @ 1% of Purchase Price is applicable. In view of the above, the taxes and duties inter-alia including entry tax applicable for the bids are calculated : Details of dicounts
a) Ex-Works Price of Direct Supplies (after discount, if any) Rs. 0 Gross LS #REF! #REF! #REF! Gross % #REF! #REF! #REF!
b) Excise Duty @ 10.3% of (a) above Rs. 0 #REF! #REF!
c) CST / VAT @ 2% of Ex-Works of Direct Supplies (a) + ED (b) above Rs. #REF! Sch-1 Direct LS #REF! #REF! #REF! Sch-1 Direct % #REF! #REF! #REF!
d) Others Rs. Sch-1 BO LS #REF! #REF! #REF! Sch-1 BO % #REF! #REF! #REF!
e) Purchase Price for Entry Tax (Total Ex-Works+F&I+ED+CST+Others) Rs. #REF! Sch-2 LS #REF! #REF! #REF! Sch-2 % #REF! #REF! #REF!
f) Entry Tax @ 1% of (e) above Rs. #REF! Sch-3 LS #REF! #REF! #REF! Sch-3 % #REF! #REF! #REF!
Sch-7 LS #REF! #REF! #REF! Sch-7 % #REF! #REF! #REF!
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation Statement of Quoted / Corrected Prices Page Different Manner #REF!
Text for Discount #REF!
23 Twenty Three
27 Twenty Seven
28 Twenty Eight
33 Thirty Three
37 Thirty Seven
38 Thirty Eight
73 Seventy Three
74 Seventy Four
75 Seventy Five
77 Seventy Seven
78 Seventy Eight
79 Seventy Nine
83 Eighty Three
87 Eighty Seven
88 Eighty Eight
93 Ninety Three
97 Ninety Seven
98 Ninety Eight
100 One Hundred
Name of Package : Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
Package No : Package DC-1
Specification No. : 5002002317/OTHERS/DOM/A06-CC CS -7
Completion Period 12 Months
: Attachments : General guidelines for filling up the Attachments : Package DC-1 :
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
Specification No.: 5002002317/OTHERS/DOM/A06-CC CS -7
1 Fill up only green shaded cells in the relevent attachments.
2 Attachments 3(JV), 3(QR), Attach QR, 4, 4(A), 4(B), 5, 6, 7, 9, 10, 11, 12, 13, 14, 15, 16, 17,18, 19 and Bid Form for 1st Envelope are included here.
3 Attachment 1 Bid Security : To be submitted as perproforma provided in the bidding document.
4 Attachment 2 Power of Attorney : No specific format is provided by POWERGRID. Bidder may use their own format.
5 Attachment 8 Manufacturer’s Authorisation Form : To be furnished as per proforma provided in the bidding document, on the letter head of the each Manufactures proposed to supply main items. Not included here.
6 Attachment 14 Integrity Pact : To be submitted as per ITB Clause No. 9.3(n) and as per remarks in the Attach 14-IP.
7 Attachment 18 Safety Pact : To be submitted as per ITB Clause No. 9.3(r) and as per remarks in the Attach 18.
8 Attachment 20: Declaration of Key Managerial Person jointly with Power of Attorney holder
9 Attachment 21: Affidavit of Self certification regarding Minimum Local Content in line with PPP-MII order, if applicable
10 Attachment 22: Certificate from statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of Local Content, in line with PPP-MII order, if applicable
11 Attachment 23: Authorization certificate issued by Domestic Manufacturer for selling Domestically Manufactured Iron & Steel Products
12 Attachment 24: Affidavit of Self certification regarding Domestic Value Addition in Iron & Steel Products
13 Attachment 25: Compliance to the process related to the e-RA Terms & Conditions and the Business Rules governing the e-RA
14 Attachment 26:Declaration by the Bidder regarding events encountered pursuant to ITB Clause 2.1
15 Attachment 27:Certification by the Bidder as per DoE Order in line with ITB Clause 2.1
Note : Enable the Active X Control & Macros. Also ensure to keep option of "Trust acess to VBA project object Model" cheched [√]. Ensure that you work on MS Excel 2007 or higher version.
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
5002002317/OTHERS/DOM/A06-CC CS -7 Sole Bidder 1
Yes JV (Joint Venture) 2 or More
Enter following details of the bidder No
Specify type of Bidder [Select from drop down menu] Sole Bidder Sole Bidder 2 0
Address of Bidder
Whether the bidder is an MSE (Micro & Small Enterprise) 0 2 2 0 2019
Enter the Name of Registration Authority 2020
E-mail ID of Bid Signatory
Mobile No. of Bid Signatory
Tel No. of Bid Signatory
Fax No. of Bid Signatory MSE 0
Name of other Partner Ram Lal
Address of other Partner G5
Name of other Partner - 2 (more, if any)
Address of other Partner - 2 (more, if any)
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-3(JV) Sole Bidder
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Joint Venture Agreement and Power of Attorney for Joint Venture*)
Bidder’s Name and Address : To:
Contract Services & Ram Lal
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
This Attachment is Not Applicable
Name(s) and Addresse(s) of other partner(s)
The Joint Venture Agreement (as per the proforma attached at no. 15 in Section-VI, Sample Forms and Procedures, Conditions of Contract, Vol.-I of the Bidding Documents) and Power of Attorney for Joint Venture (as per the proforma attached at no. 14 in Section-VI, Sample Forms and Procedures, Conditions of Contract, Vol.-I of the Bidding Documents) are enclosed herewith Sole Bidder
Date : -- Printed Name : 0
Place : Designation : 12
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-3(QR)
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Qualifying Requirement Data)
Bidder’s Name and Address (Lead Partner of) : To:
Contract Services
Name: 0 Power Grid Corporation of India Ltd.,
Address: 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
In support of the Qualification Requirements (QR) for bidders, stipulated in Annexure-A (BDS) of the Section - III (BDS), Volume-I & Additional Information required as per ITB clause 9.3(c) of the Bidding Documents, we furnish herewith our QR data/details along with other information, as follows herewith our stipulations have been reproduced in italics for ready reference, however, in case of any discrepancy the QR as given in BDS shall prevail).
* We have submitted bid as individual firm.
* We have submitted bid as joint venture of following firms :
(ii) #REF! 2 or more
(* Strike-off whichever is not applicable)
[For details regarding Qualification Requirements of a Joint Venture, please refer para 4.0 below.]
We are furnishing the following details/document in support of Qualifying requirement for the subject package.
A Attached copies of original documents defining :
a) The constitution or legal status;
b) The principal place of business;
c) The place of incorporation (for bidders who are corporations); or the place of registration and the nationality of the Owners (for applicants who are partnerships or individually-owned firms).
B Attached original & copies of the following documents :
a) Written power of attorney of the signatory of the Bid to commit the bidder.
b) Joint Venture Agreement.
1.0 GENERAL INFORMATION
Bidder is required to provide general information as per the following format.
[Where the Bidder proposes to use named subcontractor(s) for critical components of the works or for work contents in excess of ten (10) percent of the bid price, the following information should also be supplied for the subcontractor(s)].
S No. Particulars Name of the Bidder
1 Name of the Firm
2 Head Office/ Registered Office Address
5 Contact Person
6 Place of Incorporation/ Registration
7 Year of Incorporation/ Registration
8 Nationality of
9 Whether the bidder is an MSE (Micro & Small Enterprise). If Yes, attach Documentary Evidence with the Bid. No
10 Whether the Bidder is a Start-Ups Company (as defined by DIPP). If Yes, attach Documentary evidence with the Bid.
2.0 TECHNICAL REQUIREMENTS {Reference para 1.0 of Annexure-A (BDS)}
2.1 TECHNICAL EXPERIENCE
2.1.1 Route-1: The bidder must have designed, manufactured, tested & supplied 715 kV or higher voltage class one (1) number 1-phase Transformer of at least 500 MVA capacity or at least three (3) numbers 1-phase Transformers each having a capacity of at least 166 MVA, and the same transformer (s) should have been in satisfactory operation# for at least two (2) years on the date of bid opening as originally scheduled i.e., as on .………….(date to be inserted by CS department at the time of NIT).
2.1.2 Route-2: The bidder (s) who have established production line and testing facilities in India for 715 kV or above class transformer based on technological support of the Collaborator(s) for the equipment(s) can also be considered qualified provided, The bidder must have manufactured in India, type tested 715 kV or higher voltage class either One (1) no. 1-phase Transformer of at least 166 MVA capacity or One (1) no. 1-phase Reactor of at least 80 MVAR capacity and the same should have been supplied as on the date of bid opening as mentioned above based on technological support of Collaborator(s) provided that:- a) Collaborator(s) meets the Technical Experience criteria stipulated in Route-1. b) A legally enforceable undertaking jointly by Bidder and the Collaborator(s) (as per enclosed format in---------- of bidding document) is furnished along with the bid, to guarantee quality, timely supply, performance and warranty obligations for Five(5) years for entire quantity to be manufactured and supplied from the works in India and a confirmation letter from the Collaborator(s) along with the bid stating that Collaborator(s) shall furnish performance guarantee for an amount of 10% of the cost of such equipment(s). This performance guarantee shall be in addition to contract performance guarantee to be submitted by the bidder.
2.1.3 Route-3: In case, the bidder is an Indian Entity established as Subsidiary/JVC/Group company by its parent/principal, who have established production line and testing facilities in India for 715 kV or above class transformer based on technological support of the parent/principal for the equipment(s) can also be considered qualified provided, The bidder must have manufactured in India, type tested 715 kV or higher voltage class either One (1) no. 1-phase Transformer of at least 166 MVA capacity or One (1) no. 1-phase Reactor of at least 80 MVAR capacity and the same should have been supplied as on the date of bid opening as mentioned above based on technological support of Parent/ principal company provided that:- a) Parent / Principal Company meets the Technical Experience criteria stipulated in Route-1. b) A legally enforceable undertaking jointly by Bidder and the parent/ principal company (as per enclosed format in---------- of bidding document) is furnished along with the bid, to guarantee quality, timely supply, performance and warranty obligations for Five(5) years for entire quantity to be manufactured and supplied from the works in India and a confirmation letter from the parent/principal company along with the bid stating that parent/ principal company shall furnish performance guarantee for an amount of 10% of the cost of such equipment(s). This performance guarantee shall be in addition to contract performance guarantee to be submitted by the bidder.
In case bidder is a holding company, the technical experience referred to in para 2.1.1, 2.1.2 & 2.1.3 above shall be of that holding company only (i.e. excluding its subsidiary/group companies). In case bidder is a subsidiary of a holding company, the technical experience referred to in para 2.1.1, 2.1.2 & 2.1.3 above shall be of that subsidiary company only (i.e. excluding its holding company).
#satisfactory operation means certificate issued by the Employer certifying the operation without any adverse remarks.
2.1.4 Using the following format, each Bidder (individual firms or partners of a joint venture) is requested to list the experience as detailed above, on the basis of which the Bidder wishes to qualify. The information is to be summarised using following format for each experience of the Bidder
(The bidder shall attach documentary evidence, such as copies of utility certificates for completed contracts and copies of award letters etc. for ongoing contracts in support of his experience as listed in the following proforma for each Contract with the help of "Attach" Buttons provided in table given below).
2.2 Kindly mention below, whether 765 kV/ 400kV transformer(s) are being offered from Bidder himself OR from a qualified manufacturer [required to ascertain compliance to QR provision mentioned at para 1(C ), Annexure-A(BDS)].
(A) 765 kV Transformers being offered:
2.3 Format-A: (ROUTE-1) for 765kV Auto Transformer:
Format for the Bidder/ Collaborator/ Parent/Principal Company/Qualified Manufacturer of the Bidder who must have designed, manufactured, tested & supplied 715kV or Higher Voltage class Transformer in support of meeting the technical experience requirement of para 1(A) 1.1, Annexure-A to BDS, Section-III, Volume-I of the Bidding Documents)
1 Name of Bidder/Qualified Manufacturer (as applicable) : 0 0
2 Name & Address of the Collaborator/Parent /Principal Company (if applicable) 0
3 Name of Contract Undertaken (for 715kV or Higher Voltage class Transformers)
4 Contract Reference No. & Date of Award
5 Name and Address of the Employer/Utility for whom the Contract was executed by the firm
6 Voltage Level of Transformer erected under the Contract (Indicate 715kV or above class only)
7 Indicate Number of Transformer(s) under the above contract (1 phase Transformers with rating not less than 500 MVA OR Transformers in Banks of 3 single phase units of at least 166 MVA each)
8 MVA capacity of above mentioned 1-phase units
9 Name of the substation or switchyard
10 No. of years, the above Transformer are in operation as on the date of bid opening. (Originally Scheduled)
11 Scope of work involved under the Contract
(Tick whichever is/are applicable) of Transformer of Transformer of Transformer
12 Details of documents uploaded in support of the above stated experience
2.4 Format-B: (ROUTE-2) for 765kV Auto Transformer:
Format for Bidder(s)/ Manufacturer [who have established production line and testing facilities in India for 715kV or above class Transformer based on Technology Support of Collaborator(s)], in support of meeting the requirement of para 1(A) 1.2 (Route-2), Annexure-A to BDS, Section-III, Volume-I of the Bidding Documents
a Name of Bidder/Manufacturer
b Whether Bidder/Manufacturer has established production line and testing facilities in India for 715 kV or above class Transformer on the technological support of the Collaborator(s) ?
c Name of the Collaborator {The qualifying data/details for collaborator for the equipment is to be furnished in Format-A above)
Data/details of the Bidder/Manufacturer wishes/proposes to qualify through Route-2(Para 1.2, Annexure-A (BDS)), to be furnished below:
1 Name of Contract Undertaken
2 Contract Reference No. & Date of Award
3 Name and Address of the Employer/Utility for whom the Contract was executed by the Bidder
4A Indicate details below in case Contract executed for Transformer
(i) Voltage Level of Transformer manufactured & type tested under the Contract based on technological support of Collaborator. (Indicate 715kV or above class only)
(ii) MVA capacity of the above mentioned single phase Transformers
(iii) Indicate Number of Transformer(s) under the contract (Indicate nos. of single phase Transformer of atleast 166MVA)
(iv) Name of the substation or switchyard
(v) Date as on which the above mentioned Transformers supplied
(vi) whether the above Transformers are in operation as on the date of bid opening(originally scheduled).(Yes/No)
(vii) Scope of work involved under the Contract
(Tick whichever is/are applicable)
of Transformer of Transformer of Transformer
4B Indicate detail below in case Contract executed for Reactor
i Voltage Level of Reactor manufactured & type tested under the Contract based on technological support of Collaborator. (Indicate 715kV or above class only)
ii MVAR capacity of the above mentioned single phase Reactors
iii Indicate Number of Reactor(s) under the contract (Indicate nos. of Reactor(s) of at least 80 MVAR each)
iv Name of the substation or switchyard
v Date as on which the above mentioned Reactors are supplied.
vi whether the above Reactors are in operation as on the date of bid opening(originally scheduled).(Yes/No)
vii No. of years, the above Reactors are in operation as on the date of bid opening (originally scheduled).
vii Scope of work involved under the Contract
(Tick whichever is/are applicable) for Reactor for Reactor for Reactor
5 Whether collaborator(s) meets the technical experience criteria stipulated at 2.1.1 above, and the details of which is mentioned at Format-A above. (Applicable for the Bidder wish/proposes to qualify through Route-2 of Annexure-A(BDS)) Yes
6 Whether legally enforceable undertaking jointly by Bidder/Manufacturer and the Collaborator(s) (as per enclosed format in Section-VI: Sample Forms and Procedures of bidding document) is furnished along with the bid. (Applicable for the Bidder/Manufacturer(s) wish/proposes to qualify through Route-2 of Annexure-A(BDS))
7 Confirmation letter from the Collaborator along with the bid stating that Collaborator shall furnish performance guarantee, in addition to contract performance guarantee to be submitted by the bidder, for an amount of 10% of the cost of equipment(s) to be manufactured and supplied from the works in India. (Applicable for the Bidder/Manufacturer(s) wish/proposes to qualify through Route-2 of Annexure-A(BDS)) (Choose whichever is applicable from the drop down menu)
8 Details of documents uploaded in support of the above stated experience
2.5 Format-C: (ROUTE-3) for 765kV Auto Transformer:
Format for Manufacturer of the Bidder/ Indian entity established as Subsidiary/ JVC/ Group Company by its Parent/ Principal, who have established production line and testing facilities in India for 715kV or above class Transformer, in support of meeting the requirement of para 1(A) 1.3, Annexure-A to BDS, Section-III, Volume-I of the Bidding Documents)
a Name of Bidder/ Manufacturer
b Whether the bidder is an Indian Entity established as Subsidiary/JVC/Group company by its parent/principal, who have established production line and testing facilities in India for 715 kV or above class transformer based on technological support of the parent/principal?
c Name & Address of the Parent/Principal Company {The qualifying data for the Parent/Principal Company for the equipment is to be furnished in Format-A above)
Data/details of the Bidder/Manufacturer wishes/proposes to qualify through Route-3 (Para 1.3, Annexure-A (BDS)), to be furnished below:
1 Name of Contract Undertaken
2 Contract Reference No. & Date of Award
3 Name and Address of the Employer/Utility for whom the Contract was executed by the firm
4A Indicate detail below in case Contract executed for Transformer
i Voltage Level of Transformer manufactured & type tested under the Contract . (Indicate 715kV or above class only)
ii Indicate Number of Transformer(s) under the contract (Indicate nos. of single phase Transformer of atleast 166MVA )
iii MVA capacity of the above mentioned single phase Transformers
iv Name of the substation or switchyard
v Date as on which the above mentioned Transformers supplied
vi whether the above Transformers are in operation as on the date of bid opening(originally scheduled).(Yes/No)
vii No. of years, the above Transformers are in operation as on the date of bid opening (originally scheduled).
viii Scope of work involved under the Contract
(Tick whichever is/are applicable) of Transformer of Transformer of Transformer
4B Indicate detail below in case Contract executed for Reactor
i Voltage Level of Reactor manufactured & type tested under the Contract (Indicate 715kV or above class only)
ii MVAR capacity of the above mentioned single phase Reactors
iii Indicate Number of Reactor(s) under the contract (Indicate nos. of Reactor(s) of at least 80 MVAR )
iv Name of the substation or switchyard
v Date as on which the above mentioned Reactors are supplied.
vi whether the above Reactors are in operation as on the date of bid opening(originally scheduled).(Yes/No)
vii No. of years, the above Reactors are in operation as on the date of bid opening(originally scheduled)..
viii Scope of work involved under the Contract
(Tick whichever is/are applicable) for Reactor for Reactor for Reactor
5 Whether Parent/Principal company(s) meets the technical experience criteria stipulated at 2.1.1 above, and the details of which is mentioned at Format-A above. (Applicable for the Bidder/Manufacturer(s) wish/proposes to qualify through Route-3 of Annexure-A(BDS))
6 Whether legally enforceable undertaking jointly by Bidder/Manufacturer and the Parent/Pricipal company(s) (as per enclosed format in Section-VI: Sample Forms and Procedures of bidding document) is furnished along with the bid. (Applicable for the Bidder/Manufacturer(s) wish/proposes to qualify through Route-3 of Annexure-A(BDS))
7 Confirmation letter from the Parent/Principal Company along with the bid stating that Parent/Principal Company shall furnish performance guarantee, in addition to contract performance guarantee to be submitted by the bidder, for an amount of 10% of the cost of equipment(s) to be manufactured and supplied from the works in India. (Applicable for the Bidder wish/proposes to qualify through Route-3 of Annexure-A(BDS))
8 Details of documents uploaded in support of the above stated experience
3.0 Financial Position {Reference para 2.0 of Annexure-A (BDS)}
a) Net Worth for last 3 financial years should be positive.
b) Minimum Average Annual Turnover^ (MAAT) for best three (3) years i.e. 36 months out of last five (5) financial years of the bidder should be Rs. 1451.18 million or equivalent for Auto Transformer TR09. ^ Annual gross revenue from operations/gross operating income as incorporated in the profit & loss account excluding other income”.
c) Bidder shall have liquid assets (L.A.) or/and evidence of access to or availability of credit facilities of not less than Rs. 241.86 million or equivalent for Auto Transformer TR09.
Note: (i) In case bidder is a holding company, the Financial Position criteria referred to in para 3.0 above shall be that of holding company only (i.e. excluding its subsidiary / group companies). In case bidder is a subsidiary of a holding company, the Financial Position criteria referred to in para 3.0 above shall be that of subsidiary company only (i.e. excluding its holding company). (ii) In case bidder has established manufacturing facility in India and yet to complete three (3) financial years, the Net Worth and average of the turnover as per financial statement for completed financial years shall be considered for the purpose of compliance to the specified Net Worth and MAAT requirements. (iii) In case of bidder qualifying through Route-3 but not meeting the Financial Position requirement as per note (i) read along with note (ii) above, the following shall be applicable: In case bidder is yet to complete five (5) years from the date of commercial production of such equipment(s) but no later than seven (7) years from the date of incorporation of the said company as on the originally scheduled date of bid opening as above, the financial position requirement as per para 3.0 (b) & (c) of parent/principal company providing collaboration for technological support shall be considered. However, once he meets the turnover requirement on their own or completes five (5) years from the date of commercial production of such equipment (s) in India but no later than seven (7) years from the date of incorporation as on the originally scheduled date of bid opening as above, the financial position requirements as specified at 3.0 (b) and (c) above shall be required to be met by such bidder on their own as per note (i) above and not based on their parent/principal company. Further, in case the bidder is yet to complete one (1) financial year, the Net worth requirement as per para 3.0 (a) above of parent/principal shall be considered.
(iv) Relaxation for Start-Ups^/ MSEs Start-Ups^/ MSEs, meeting the specified requirements at Para 3.0 (a) above in Financial Position shall also be considered qualified if they meet Eighty (80) % of the requirement specified at Para 3.0 (b) & 3.0 (c) above in Financial Position. ^ Start-Ups as defined by DIPP, applicable as on the originally scheduled date of bid opening.
{In support of its ‘Financial Position’, in line with the above, the Bidder or Company/Constituents must provide the relevant information in support of the same, along with documentary evidence, in the following format}
4.0 Financial Qualification Data: 2 or more
4.1 Name of the Bidder
Networth (in Rs. Millions) Details of documentary evidence submitted in support of Qualification Data
Sl No Financial year
For the FY of immediately preceding the date of submission of bid.
B Turnover details:
Turnover (in Rs. Millions) Details of documentary evidence submitted in support of Qualification Data
Sl No Financial year
For the FY of immediately preceding the date of submission of bid.
Average Annual Turnover for best Three Years is
C Liquid Assets
LA (in Rs. Millions) Details of documentary evidence submitted in support of Qualification Data
Details of evidence of having Liquid assets (LA)
Details of evidence of access to or availability of credit facilities
5.0 Financial Qualification Data for Parent/Principal Company (If Applicable):
5.1 Name of the Bidder
Details of documentary evidence submitted in support of Qualification Data
Networth (in Rs. Millions)
Sl No Financial year
For the FY of immediately preceding the date of submission of bid.
B Turnover details:
Details of documentary evidence submitted in support of Qualification Data
Turnover (in Rs. Millions)
Sl No Financial year
For the FY of immediately preceding the date of submission of bid.
Average Annual Turnover for best Three Years is
C Liquid Assets
LA (in Rs. Millions) Details of documentary evidence submitted in support of Qualification Data
Details of evidence of having Liquid assets (LA)
Details of evidence of access to or availability of credit facilities
Equivalent US$ (in Million) exchange rate* Details of documentary evidence submitted in support of Qualification Data
Networth (in Millions)
Sl No Financial year
Do you have audited results for FY 2016-17 Yes
*(Indicate the rate(s) of exchnage against US Dollar at the end of each year, which have been used for arriving the amount at equivalent US Dollar.)
B Turnover details:
Equivalent US$ (in Million) exchange rate* Details of documentary evidence submitted in support of Qualification Data
Turnover (in Millions)
Sl No Financial year
Do you have audited results for FY 2016-17 Yes
*(Indicate the rate(s) of exchnage against US Dollar at the end of each year, which have been used for arriving the amount at equivalent US Dollar.)
C Liquid Assets
LA Equivalent US$ (in Million)
Details of evidence of having Liquid assets (LA)
Details of evidence of access to or availability of credit facilities
Equivalent US$ (in Million) exchange rate* Details of documentary evidence submitted in support of Qualification Data
Networth (in Millions)
Sl No Financial year
Do you have audited results for FY 2016-17 Yes
*(Indicate the rate(s) of exchnage against US Dollar at the end of each year, which have been used for arriving the amount at equivalent US Dollar.)
B Turnover details:
Equivalent US$ (in Million) exchange rate* Details of documentary evidence submitted in support of Qualification Data
Turnover (in Millions)
Sl No Financial year
Do you have audited results for FY 2016-17 Yes
Average Annual Turnover for best Three Years is
*(Indicate the rate(s) of exchnage against US Dollar at the end of each year, which have been used for arriving the amount at equivalent US Dollar.)
C Liquid Assets
LA Equivalent US$ (in Million)
Details of evidence of having Liquid assets (LA)
Details of evidence of access to or availability of credit facilities
4.0 Joint Venture (JV) Firms {Reference para 3.0 of Annexure-A (BDS)}
In case a bid is submitted by a Joint Venture (JV) of two or more firms as partners, all the partners of Joint Venture shall meet collectively requirements stipulated at clauses 3.0 (b) & 3.0 (c) above. The figure of average annual turnover and liquid assets/credit facilities for each of the partners of the JV shall be added together to determine the JV’s compliance with the minimum qualifying criteria set out in Para 3.0 (b) & (c) above.
However, for a JV to be qualified, the partner(s) of JV must also meet the following minimum criteria: i. All the partners of the JV shall meet individually the Financial Position criteria given at 3.0 (a) above. ii. The Lead Partner shall meet, not less than 40% of the minimum criteria given at clause 3.0 (b) & (c) and 100 % of the criteria given above at clause 2.1 iii. The other partner(s) shall meet not less than 25% of the criteria given at clause 3.0 (b) & (c) above and 100 % of the criteria given above at clause 2.1 or 2.2 Failure to comply with this requirement will result in rejection of the joint venture’s bid.
In case of Joint venture, the following conditions shall also apply:
(a) the bid, and in case of successful bid, the specified Form of Agreement shall be signed so as to be legally binding on all partners (as per enclosed format in Section-VI, Vol.-I of bidding document).
(b) one of the partners shall be nominated as Lead Partner, and the Lead Partner shall be authorized to incur liabilities and receive instructions for and on behalf of any and all partners of the Joint Venture, and the entire execution of the Contract shall be done with the Lead Partner and payment under the contract shall be received by the Lead Partner on behalf of the Joint Venture as per power conferred to him in the Power of Attorney. The authorization shall be evidenced by submitting a Power of Attorney signed by legally authorized signatory of all the partners as per Performa in in Section-VI, Vol.-I of bidding documents. The payment under the Contract can also be received by other partner(s) based on authorization of Lead Partner.
(c) All partners of the joint venture shall be liable jointly and severally for the execution of the Contract in accordance with the Contract terms and a statement to this effect shall be included in the authorisation mentioned under (b) above as well as in the Bid Form and in the Contract Form (in case of a successful bid);
(d) Agreement entered into by the Joint Venture partners shall be submitted with the bid.
The bidder shall furnish documentary evidence in support of the qualifying requirement stipulated as above.
4.1 In accordance with the above, in case of JV bidders, it should be ensured that necessary details including those pertaining to each JV partner are furnished and the documents are submitted alongwith the bid. Further, the JV bidders should also ensure that other requirements are complied with. The lists of documents furnished are to be indicated below :
A For Name of the Bidder
6.0 The Bidder shall also furnish following documents/details with its bid. {Reference ITB clause 9.3 (c)}
6.1 The complete annual reports together with Audited statement of accounts of the company for last five years of its own (separate) immediately preceding the date of submission of bid.
Note I. In the event the bidder is not able to furnish the information of its own (i.e separate), being a subsidiary company and its accounts are being consolidated with its group/holding/parent company, the bidder should submit the audited balance sheets, income statements, other information pertaining to it only (not of its group/Holding/Parent Company) duly certified by any one of the authority [ (i) Statutory Auditor of the bidder /(ii) Company Secretary of the bidder or (iii) A certified Public Accountant] certifying that such information/documents are based on the audited accounts as the case may be.
II. Similarly, if the bidder happens to be a Group/Holding/Parent Company, the bidder should submit the above documents/information of its own (i.e. exclusive of its subsidiaries) duly certified by any one of the authority mentioned in Note-I above certifying that these information/documents are based on the audited accounts, as the case may be.
6.2 The Bidder should accordingly also provide the following information/documents
Audited balance sheet and income statements for the last five years as per the following:
A Years preceding to the bid opening Audited Balance Sheet and Income Statements enclosed
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-3(QR)
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Qualifying Requirement Data)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
For our Qualifying Requirements Data, please refer Schedule-QR of this volume.
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Qualifying Requirement Data)
Bidder’s Name and Address : To:
Contract Services
Name: 0 Power Grid Corporation of India Ltd.,
Address: 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
In support of the Qualification Requirements (QR) for bidders, stipulated in Annexure-A (BDS) of the Section - III (BDS), Volume-I & Additional Information required as per ITB clause 9.3(c) of the Bidding Documents, we furnish herewith our QR data/details along with other information, as follows herewith our stipulations have been reproduced in italics for ready reference, however, in case of any discrepancy the QR as given in BDS shall prevail).
* We have submitted bid as individual firm.
* We have submitted bid as joint venture of following firms :
(* Strike-off whichever is not applicable)
[For details regarding Qualification Requirements of a Joint Venture, please refer para 4.0 below.]
We are furnishing the following details/document in support of Qualifying requirement for the subject package.
A Attached copies of original documents defining :
a) The constitution or legal status;
b) The principal place of business;
c) The place of incorporation (for bidders who are corporations); or the place of registration and the nationality of the Owners (for applicants who are partnerships or individually-owned firms).
B Attached original & copies of the following documents :
a) Written power of attorney of the signatory of the Bid to commit the bidder.
b) Joint Venture Agreement.
1.0 GENERAL INFORMATION
Bidder is required to provide general information as per the following format.
[Where the Bidder proposes to use named subcontractor(s) for critical components of the works or for work contents in excess of ten (10) percent of the bid price, the following information should also be supplied for the subcontractor(s)].
S No. Particulars Name of the Bidder
1 Name of the Firm 0
2 Head Office/ Registered Office Address
5 Contact Person
6 Place of Incorporation/ Registration
7 Year of Incorporation/ Registration
8 Nationality of
9 Whether the bidder is an MSE (Micro & Small Enterprise). If Yes, attach Documentary Evidence with the Bid.
10 Whether the Bidder is a Start-Ups Company (as defined by DIPP). If Yes, attach Documentary evidence with the Bid.
2.0 TECHNICAL REQUIREMENTS {Reference para 1.1 of Annexure-A (BDS)}
2.1 TECHNICAL EXPERIENCE
2.1.1 Bidder should have completed building works (minimum One Basement + Ground + 3 storeys) - Institutional/ Commercial/Residential/Data Centre buildings as a prime contractor during the last seven (7) years as on the originally scheduled date of bid opening i.e. 02/08/2022 as per following: a) Under one contract of value of not less than Rs. 40.69 Cr OR b) Under two contracts each of value not less than Rs. 25.43 Cr. OR c) Under three contracts each of value of not less than Rs. 20.34 Cr Notes: In case bidder is a holding company, the technical experience referred to in clause 1.1 shall be of that holding company only (i.e. excluding its subsidiary/group companies). In case bidder is a subsidiary of a holding company, the technical experience referred to in clause 1.1 shall be of that subsidiary company only (i.e. excluding its holding company).
2.1.2 Using the following format, each Bidder is requested to list the experience as detailed above, on the basis of which the Bidder wishes to qualify. The information is to be summarised using following format for each experience of the Bidder
(The bidder shall attach documentary evidence, such as copies of utility certificates for completed contracts and copies of award letters etc. for ongoing contracts in support of his experience as listed in the following proforma for each Contract with the help of "Attach" Buttons provided in table given below).
Format for the Bidder in support of meeting the requirement of para 1.1.1, Annexure-A to BDS, Section-III, Volume-I of the Bidding Documents)
Bidder’s Name :
Details of Contract No.-1 Details of Contract No.-2 Details of Contract No.-3
1 Name of Contract Undertaken
2 Contract Reference No. & Date of Award
3 Name and Address of the Employer/Utility for whom the Contract was executed by the firm
4 Nature of the Building Works (institutional / commercial / Residential buildings)
5 Whether the Work executed as a Prime Contractor?
6 Total value of the Contract in INR Crores?
7 Completion Date of the above mentioned Work
8 Details of documents uploaded in support of the above stated experience
3.0 FINANCIAL REQUIREMENTS :
Financial Position {Reference para 1.2 of Annexure-A (BDS)}
a) Net worth of the bidder for last three (03) financial years should be positive b) Minimum average Annual Turnover (MAAT)* of the bidder for best three (03) years i.e. 36 months out of last five (05) financial years of the bidder should be Rs. 76.29 Cr. *Note- “Annual gross revenue from operations / gross operating income as incorporated in the profit & loss account excluding other operative income / other income” c) Bidder shall have liquid assets (L.A.) or/and evidence of access to or availability of credit facilities of not less than Rs. 12.715 Cr. Notes: (i) In case bidder is a holding company, financial position criteria referred to in clause 1.2 above shall be of that holding company only (i.e. excluding its subsidiary/group companies). In case bidder is a subsidiary of a holding company, the financial position criteria referred to in clause 1.2 above shall be of that subsidiary company only (i.e. excluding its holding company). (ii) Relaxation for Start-Ups^ / MSEs Start-Ups^/MSEs, meeting the specified requirements at Para 1.2 (a) above in Financial position shall also be considered qualified if they meet Eighty (80) % of the requirement specified at Para 1.2 (b) & 1.2 (c) above in Financial position. ^Start-Ups as defined by DIPP, applicable as on the originally scheduled date of bid opening
{In support of its ‘Financial Position’, in line with the above, the Bidder (in case of bidding by single firm ) or Company/Constituents must provide the relevant information in support of the same, along with documentary evidence, in the following format}
4.0 Financial Qualification Data:
Details of documentary evidence submitted in support of Qualification Data
Networth (in Rs. Millions)
Sl No Financial year
Do you have complete annual reports together with Audited statement of accounts of the company for FY 2020-21 (refer ITB Clause 9.3(c)) Yes
B Turnover details:
Details of documentary evidence submitted in support of Qualification Data
Turnover (in Rs. Millions)
Sl No Financial year
Do you have complete annual reports together with Audited statement of accounts of the company for FY 2020-21 (refer ITB Clause 9.3(c)) Yes
Average Annual Turnover for best Three Years is
C Liquid Assets
LA (in Rs. Millions) Details of documentary evidence submitted in support of Qualification Data
Details of evidence of having Liquid assets (LA)
Details of evidence of access to or availability of credit facilities
5.0 The Bidder shall also furnish following documents/details with its bid. {Reference ITB clause 9.3 (c)}
5.1 The complete annual reports together with Audited statement of accounts of the company for last five years of its own (separate) immediately preceding the date of submission of bid.
Note I. In the event the bidder is not able to furnish the information of its own (i.e separate), being a subsidiary company and its accounts are being consolidated with its group/holding/parent company, the bidder should submit the audited balance sheets, income statements, other information pertaining to it only (not of its group/Holding/Parent Company) duly certified by any one of the authority [ (i) Statutory Auditor of the bidder /(ii) Company Secretary of the bidder or (iii) A certified Public Accountant] certifying that such information/documents are based on the audited accounts as the case may be.
II. Similarly, if the bidder happens to be a Group/Holding/Parent Company, the bidder should submit the above documents/information of its own (i.e. exclusive of its subsidiaries) duly certified by any one of the authority mentioned in Note-I above certifying that these information/documents are based on the audited accounts, as the case may be.
5.2 The Bidder should accordingly also provide the following information/documents
Audited balance sheet and income statements for the last five years as per the following:
A Years preceding to the bid opening Audited Balance Sheet and Income Statements enclosed
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-4
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Form of Certificate of Origin and Eligibility)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
We hereby certify that equipment and materials to be supplied are produced in [Name of Countries], eligible source country. Equipments & Materials produced in [Name of countries] Company incorporated & registered in [Name of countries]
We hereby certify that our company is incorporated and registered in [Name of Countries], eligible source country. [Name of Countries] [Name of Countries] [Name of Countries], [Name of Countries],
Date : -- Printed Name :
Place : Designation :
country. country. [Name of Countries], [Name of Countries],
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-4(A)
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(List of Special Maintenance Tools & Tackles)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
We are furnishing below the list of special maintenance tools & tackles for various equipment under the subject package. The prices for these tools & tackles are included in our lumpsum bid price. We further confirm that the list of special maintenance tools & tackles includes all the items specifically identified in your bidding documents as brought out below:
S.No. For Equipment Item Description Unit Quantity
Notwithstanding what is stated above, we further confirm that any additional special maintenance tools and tackles, required for the equipment under this package shall be furnished by us at no extra cost to the employer.
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-4(B)
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(List of Special Maintenance Tools & Tackles)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
We are furnishing below the list of special maintenance tools & tackles for various equipment under the subject package. The prices for these tools & tackles which are to be taken back after the completion of the work by us are not included in our lumpsum bid price. We further confirm that the list of special maintenance tools & tackles includes all the items specifically identified in your bidding documents as brought out below:
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-5
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Bought-out & Sub-contracted Items)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
We hereby furnish the details of the items/ sub-assemblies, we propose to buy for the purpose of furnishing and installation of the subject Package:
Sl. No. Item Description Quantity proposed to be bought/sub-contracted Details / write-up to engage the Locals sub-contractor/sub-vendor
Name Nationality
We hereby declare that, we would not subcontract the erection portion of the contract without the prior approval of Employer.
We hereby furnish the details of the items/ sub-assemblies propose to supply from our own works (i.e. as direct transactions) in additional to the supplies the same from other vendors (i.e. as Bought-out transactions) as detailed in the table given above. In line with ITB Clause 9.3 (e), we intend to supply following items which are to be manufactured within Arunachal Pradesh. We further declare that we would source material / services for atleast 30% of the Installation Price of Services contract from within Assam
Sl. No. Item Description Quantity proposed to be supplied Details / write-up to engage the Locals sub-contractor/sub-vendor
Name of Plant Address
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Annexure I to Attachment-5
(Bought-out & Sub-contracted Items)
Sl. No. Item Description Quantity proposed to be bought/sub-contracted Details / write-up to engage the Locals sub-contractor/sub-vendor
Name Nationality
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Annexure I to Attachment-5
(Bought-out & Sub-contracted Items)
Sl. No. Item Description Details of the proposed sub-contractor/sub-vendor Details / write-up to engage the Locals sub-contractor/sub-vendor
Name Nationality
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-5A
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Items, Components, Raw Material, Services proposed to be sourced from Micro and Small Enterprises)
Bidder's Name and Address: To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
1 We hereby furnish the details of the items, components, raw material, services which we propose to buy/avail from Micro and Small Enterprises (MSEs) for the purpose of completion of works under the subject package:
Sl. No. Item Description Quantity proposed to be bought/sub-contracted Name of Micro and Small Enterprises (MSEs)
Name Category (Micro or Small)
2 The above is a list of items we propose to procure from MSEs. However, based on the situations during the execution of the contract, the above list may undergo changes. We hereby confirm that the details regarding actual procurement from MSEs carried out by us, as per the format provided at Section VI, Forms and Procedures, Volume-I of bidding documents, shall be submitted along with the bills for payment against supplies made/works done during execution of contract.
We hereby furnish the details of the items/ sub-assemblies propose to supply from our own works (i.e. as direct transactions) in additiona to the supplies the same from other vendors (i.e. as Bought-out transactions) as detailed in the table given above.
Sl. No. Item Description Quantity proposed to be supplied Details of the plant from where supplies are proposed.
Name of Plant Address
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-5A
(Bought-out & Sub-contracted Items)
Sl. No. Item Description Quantity proposed to be bought/sub-contracted Name of Micro and Small Enterprises (MSEs)
Name Category (Micro or Small)
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-6
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Alternative, Deviations and Exceptions to the Provisions)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
The bidder shall itemize any deviation from the Specifications included in his bid. Each item shall be listed (separate sheets may be used and enclosed with this Attachment) with the following information:
Sl. No. Reference clause in the Specifications Deviation Cost of withdrawal of the deviation
The above deviations and variations are exhaustive. We confirm that we shall withdraw the deviations proposed by us at the cost of withdrawal indicated in this attachment, failing which our bid may be rejected and Bid Security forfeited.
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Annexure I toAttachment-6
(Alternative, Deviations and Exceptions to the Provisions)
Sl. No. Reference clause in the Specifications Deviation Cost of withdrawal of the deviation
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-7
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Details of Alternative Bid)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
No Alternative Bid
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Work Completion Schedule)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
We hereby declare that the following Work Completion Schedule shall be followed by us in furnishing and installation of the subject Package i.e., Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation. for the period commencing from the effective date of Contract to us :
Sl. No. Description of Work Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
1 Detailed Engineering and drawing submission
a) commencement
2 Procurement of equipment/ components & assembly
a) commencement
a) commencement
3 Shipments & Delivery
a) commencement
4 Establishment of site office
5 Installation at Site
a) commencement
6 Testing & Pre-commissioning
a) commencement
7 Trial Operation
a) commencement
Date : -- Printed Name :
Place : Designation :
Note : Bidders to enclose a detailed network covering all the activities to be undertaken for completion of the project indicating key dates for various milestones for each phase constituent-wise.
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-10
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Guarantee Declaration)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
Dear Sir, We conform that the equipments offered shall have minimum perfromnace specified in Technical Specification. We further guarantee the performance/efficiency of the equipments in response to the Technical Specifications.
Date -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-11
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Information regarding Ex-employees of POWERGRID in our Organisation)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
We declare that we are aware of and have gone through the “Code of Business Conduct and Ethics for Senior Management Personnel”1 and “Code of Business Conduct and Ethics for Board Members”1 of POWERGRID (hereinafter referred to as the “Code of Conduct”). We further understand that as per the “Code of Conduct”, Senior Management Personnel including Board Members, who have retired/resigned from POWERGRID, shall not accept any appointment or post, as detailed in the referred “Code of Conduct”, within 1 year from the date of cessation of service/directorship unless approved by the Competent Authority. Accordingly, we hereby furnish the details of ex-employees of POWERGRID who had retired/ resigned at the level of General Manager and above from POWERGRID and subsequently have been employed by us:
Sl. No. Name of the person with designation in POWERGRID Date of Retirement/ resignation from POWERGRID Date of joining and designation in our organisation*
*In case the date of joining in the bidder’s organization of such ex-employee is within 1 year from the date of retirement/resignation from POWERGRID, No Objection Certificate/ approval from the Competent Authority must be furnished along with the bid or subsequent through clarification pursuant to ITB Clause 21.
In case of non-submission of No Objection Certificate/approval of the Competent Authority, as required, We understand that POWERGRID shall deal with such cases as per its Policy and procedures in vogue, which may also result in rejection of our bid. We also confirm that POWERGRID shall be the sole judge in this regard. We further declare that any misrepresentation or submission of false/forged documents/information in this regard shall be dealt with as per the provisions of the Integrity Pact and/or the Bidding Documents and/or POWERGRID’s policy and procedures.
Date : -- Printed Name :
Place : Designation :
Note: 1. “Code of Business Conduct and Ethics for Senior Management Personnel” and “Code of Business Conduct and Ethics for Board Members” are available on POWERGRID’s website https://www.powergridindia.com. 2. The information in similar format should be furnished for each partner of joint venture in case of joint venture bid. 3. In case bidder has furnished no details on ex-employees of POWERGRID or has left blank or has indicated ‘-‘ against the same, it shall be deemed that they have not employed any such person in their organization.
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-11
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Information regarding Ex-employees of POWERGRID in our Organisation)
Name(s) and Addresse(s) of other partner(s) To:
Contract Services
Name : Ram Lal Power Grid Corporation of India Ltd.,
Address : G5 "Saudamini", Plot No. 2, Sector 29
Gurgaon Gurgaon (Haryana) - 122001
We hereby furnish the details of ex-employees of POWERGRID who had retired/ resigned at the level of General Manager and above from POWERGRID and subsequently have been employed by us:
Sl. No. Name of the person with designation in POWERGRID Date of Retirement/ resignation from POWERGRID Date of joining and designation in our organisation
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-11
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Information regarding Ex-employees of POWERGRID in our Organisation)
Name(s) and Addresse(s) of other partner(s) To:
Contract Services
Name : Power Grid Corporation of India Ltd.,
Address : "Saudamini", Plot No. 2, Sector 29
Gurgaon (Haryana) - 122001
We hereby furnish the details of ex-employees of POWERGRID who had retired/ resigned at the level of General Manager and above from POWERGRID and subsequently have been employed by us:
Sl. No. Name of the person with designation in POWERGRID Date of Retirement/ resignation from POWERGRID Date of joining and designation in our organisation
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 ATTACHMENT-12
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Price Adjustment Data)
Bidder’s Name and Address (Sole Bidder) : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No.-2
0 Gurgaon (Haryana) - 122001
We hereby furnish the relevant details pertaining to the price adjustment provisions for equipment as specified in your specifications and documents for the Package DC-1. The necessary documentary evidence is enclosed.
Sl. No. Name of Materials/Labour Value of co-efficient Name of the published index Value of index as 30 days prior to date set for opening of bids
In accordance with Clause 2, Appendix-2, Form of Contract Agreement, Section-VI; Forms. Volume-I
A. Price Adjustment for Erection Price Component
1 Erection price component {including Civil Works but excluding ‘Supply & Placement of reinforcement steel’ and ‘Concreting’}
i) High Speed Diesel, coefficient a = Wholesale Price Index Number for `HSD’ (Individual Commodity) (monthly) (Base: 2011-12=100), as published by Office of Economic Advisor, Ministry of Commerce & Industry(www.eaindustry.nic.in)
ii) Labour, coefficient l = Indian field labour index – namely All-India Average Consumer Price Index Numbers for Industrial Workers (monthly) (Base 2016=100), as published by Labour Bureau, Shimla, Government of India (http://labourbureaunew.gov.in).
Coefficient ‘a’ shall be between 0.20 to 0.24 and Coefficient ‘l’ shall be between 0.56 to 0.60 and sum of Coefficients ‘a’ and ‘l’ shall be 0.80
2 Supply and placement of reinforcement steel
i) HSD, a= Wholesale Price Index Number for `HSD’ (Individual Commodity) (monthly) (Base: 2011-12=100), as published by Office of Economic Advisor, Ministry of Commerce & Industry(www.eaindustry.nic.in)
ii) Labour, l= Indian field labour index – namely All-India Average Consumer Price Index Numbers for Industrial Workers (monthly) (Base 2016=100), as published by Labour Bureau, Shimla, Government of India (http://labourbureaunew.gov.in).
iii) Manufacture of Basic Metals, b= Wholesale Price Index Number for `Manufacture of Basic Metals’(Group Item) (monthly) (Base: 2011-12=100), as published by Office of Economic Advisor, Ministry of Commerce & Industry(www.eaindustry.nic.in).
Coefficient ‘a’ shall be between 0.09 to 0.11, Coefficient ‘b’ shall be between 0.63 to 0.67 and coefficient ‘l’ shall be between 0.04 to 0.06 and sum of Coefficients ‘a’, ‘b’ and ‘l’ shall be 0.80
3 For Concereting
i) HSD, a= Wholesale Price Index Number for `HSD’(Individual Commodity) (monthly) (Base: 2011-12=100), as published by Office of Economic Advisor, Ministry of Commerce & Industry(www.eaindustry.nic.in)
ii) Labour, l= Indian field labour index – namely All-India Average Consumer Price Index Numbers for Industrial Workers (monthly) (Base 2016=100), as published by Labour Bureau, Shimla, Government of India (http://labourbureaunew.gov.in).
iii) Manufacture of cement, lime and plaster, b= Wholesale Price Index Number for `Manufacture of cement, lime and plaster’(Group Item) (monthly) (Base: 2011-12=100), as published by Office of Economic Advisor, Ministry of Commerce & Industry (www.eaindustry.nic.in)
iv) Cutting, shaping and finishing of stone, c= Wholesale Price Index Number for `Cutting, shaping and finishing of stone’(Group Item) (monthly) (Base: 2011-12=100), as published by Office of Economic Advisor, Ministry of Commerce & Industry(www.eaindustry.nic.in).
Coefficient ‘a’ shall be between 0.18 to 0.22, Coefficient ‘b’ shall be between 0.25 to 0.35, Coefficient ‘c’ shall be between 0.18 to 0.22 and Coefficient ‘l’ shall be between 0.09 to 0.11 and sum of Coefficients ‘a’, ‘b’, ‘c’ and ‘l’ shall be 0.80
The Bidders are required to estimate and indicate the values of different coefficients for each of the items in the price variation formulae within the specified range such that their summation is as specified in the Bidding Documents. Where no value or ‘-’ or ‘shall be furnished later’ is specified against the coefficient, the same will be deemed to be zero and the fixed component would be suitably adjusted. If the values of all coefficients in price variation formulae indicated by the Bidder are within the specified range but their sum exceeds the summation specified in the Bidding Documents, the values of the coefficients shall be pro-rata adjusted such that the summation remains as per the provisions of the Bidding Documents. If the values of all coefficients indicated by the Bidder are within the specified range but their summation is less than the value specified in the Bidding Documents, the values of the coefficients as indicated by the Bidder shall be considered as such and the fixed component in the price variation formulae would be suitably adjusted. Further, if any of values of the coefficients indicated by the Bidder is out of the range specified in the Bidding Documents, the lower of the values, as indicated by the Bidder vis-à-vis lower value of the range for that coefficient specified in the Bidding Documents, shall be considered and the fixed component would be suitably adjusted.
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-13
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Declaration regarding Social Accountability)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
We conform that we stand committed to comply to all requirements of Social Accountability Standards i.e., SA8000 (latest Standard available at www.sa-intl.org) and maintain the necessary records.
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-14
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
Integrity Pact is annexed herewith this Volume.
Date : -- Printed Name :
Place : Designation :
Instruction for printing & submitting Integrity Pact
1. The requisite format of Integrity Pact is getting generated automatically and displayed here below.
2. Take print out of first page on a non-judicial stamp paper of Rs. 100/- and other seven pages on plain A4 size paper. Such two sets shall be prepared by the bidder.
3. All the pages of both the copies of the Integrity Pact shall be signed by the authorised representative of the bidder and duly stamped.
4. Both the original copies shall be submitted by the bidder in the form of Hard Copy as part of the first envelope before due date & time of submission of the bid.
5. For further details bidders may please refer ITB Clause 9.3 (o).
Power Grid Corporation of India Limited
having its Registered Office at B-9, Qutab Institutional Area, Katwaria Sarai,New Delhi – 110016 hereinafter referred to as
having its Registered Office at 0 0 0
hereinafter referred to as
"The Bidder/Contractor"
POWERGRID intends to award, under laid-down organisational procedures, contract(s) for Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
Integrity Pact Page 1 of 8
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation. and Specification Number 5002002317/OTHERS/DOM/A06-CC CS -7. POWERGRID values full compliance with all relevant laws of the land, rules, regulations, economic use of resources, and of fairness/transparency in its relations with its Bidders/ Contractors.
In order to achieve these goals, POWERGRID and the above named Bidder/Contractor enter into this agreement called 'Integrity Pact' which will form a part of the bid.
It is hereby agreed by and between the parties as under:
Section I - Commitments of POWERGRID
(1) POWERGRID commits itself to take all measures necessary to prevent corruption and to observe the following principles :
a) No employee of POWERGRID, personally or through family members, will in connection with the tender, or the execution of the contract, demand, take a promise for or accept, for him/herself or third person, any material or other benefit which he/she is not legally entitled to.
b) POWERGRID will, during the tender process treat all Bidder(s) with equity, fairness and reason. POWERGRID will in particular, before and during the tender process, provide to all Bidder(s) the same information and will not provide to any Bidder(s) confidential/ additional information through which the Bidder(s) could obtain an advantage in relation to the tender process or the contract execution.
c) POWERGRID will exclude from evaluation of Bids its such employee(s) who has any personal interest in the Companies/Agencies participating in the Bidding/Tendering process and all known prejudiced persons.
(2) If POWERGRID obtains information on the conduct of any of its employee which is a criminal offence under the IPC/PC Act, or if there be a substantive suspicion in this regard, POWERGRID will inform its Chief Vigilance Officer and in addition disciplinary actions can be initiated under POWERGRID's Rules.
Section II - Commitments of the Bidder/Contractor
(1) The Bidder/Contractor commits itself to take all measures necessary to prevent corruption. The Bidder/Contractor commits itself to observe the following principles during its participation in the tender process and during the contract execution :
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
Integrity Pact Page 2 of 8
a) The Bidder/Contractor will not, directly or through any other person or firm, offer, promise or give to any of POWERGRID's employees involved in the tender process or the execution of the contract or to any third person any material or other benefit which it is not legally entitled to, in order to obtain in exchange an advantage of any kind whatsoever during the tender process or the execution of the contract.
b) The Bidder/Contractor will not enter into any illegal or undisclosed agreement or understanding, whether formal or informal with other Bidders/Contractors. This applies in particular to prices, specifications, certifications, subsidiary contracts, submission or non-submission of bids or actions to restrict competitiveness or to introduce cartelization in the bidding process.
c) The Bidder/Contractor shall not pass any information provided by POWERGRID as part of business relationship to others and shall not commit any offence under PC/IPC Act.
d) The Bidder/Contractor of foreign origin shall disclose the name and address of the Agents/representatives in India, if any, involved directly or indirectly in the Bidding. Similarly, the Bidder/Contractor of Indian Nationality shall furnish the name and address of the foreign principals, if any, involved directly or indirectly in the Bidding.
e) The Bidder/Contractor will, when presenting his bid, disclose any and all payments made, or committed to or intends to make to agents, brokers or any other intermediaries in connection with the award of the contract and/or with the execution of the contract.
f) The Bidder/Contractor will not misrepresent facts or furnish false/forged documents/informations in order to influence the bidding process or the execution of the contract to the detriment of POWERGRID.
g) The Bidder/Contractor shall ensure adoption of Integrity Pact by its Sub-contractors and shall be responsible for the same.
(2) The Bidder/Contractor will not instigate third persons to commit offences outlined above or be an accessory to such offences.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
Integrity Pact Page 3 of 8
Section III- Disqualification from tender process and exclusion from future contracts
(1) If the Bidder, before contract award, has committed a transgression through a violation of Section II or in any other form such as to put his reliability or credibility as Bidder into question, POWERGRID may disqualify the Bidder from the tender process or terminate the contract, if already signed, for such reason.
(2) If the Bidder/Contractor has committed a transgression through a violation of Section II such as to put his reliability or credibility into question, POWERGRID may, after following due procedures, ban/blacklist the Bidder/Contractor in line with POWERGRID's policy for "Black-Listing of Firms/Banning of Business". The imposition and duration of the ban will be determined by the severity of the transgression. The severity will be determined by the circumstances of the case, in particular the number of transgressions, the postion of the transgressors within the company hierarchy of the Bidder/Contractor and the amount of the damage. The ban will be imposed for a maximum of 3 years.
(3) If the Bidder/Contractor can prove that he has restored/recouped the damage caused by him and has installed a suitable corruption prevention system, POWERGRID may revoke the ban prematurely.
Section IV - Liability for violation of Integrity Pact
(1) If POWERGRID has disqualified the Bidder from the tender process prior to the award under Section III, POWERGRID is entitled for the forfeiture of the Bid Guarantee under the Bid.
(2) If POWERGRID has terminated the contract under Section III or if POWERGRID is entitled to terminate the contract under Section III, POWERGRID shall be entitled to forfeit the Contract Performance Guarantee of this contract, in full or part thereof as may be decided, besides resorting to other remedies under the contract.
Section V- Previous Transgression
(1) The Bidder shall disclose in its Bid any transgressions occurred in the last 10 years with any other Public Sector Undertaking or Government Department or any other Company, in any country, that may impinge on the Anti-corruption principle.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
Integrity Pact Page 4 of 8
(2) If the Bidder makes incorrect statement on this subject, it can be disqualified from the tender process or the contract, if already awarded, can be terminated for such reason and further action can be taken in line with POWERGRID's policies.
Section VI - Equal treatment to all Bidders / Contractors
(1) POWERGRID will enter into agreements with identical conditions as this one with all Bidders.
(2) POWERGRID will disqualify from the tender process any bidder who does not sign this Pact or violate its provisions.
Section VII - Punitive Action against violating Bidders / Contractors
If POWERGRID obtains knowledge of conduct of a Bidder or a Contractor or its subcontractor or of an employee or a representative or an associate of a Bidder or Contractor or his Subcontractor which constitutes corruption, or if POWERGRID has substantive suspicion in this regard, POWERGRID will inform the Chief Vigilance Officer (CVO).
(*)Section VIII - Independent External Monitor/Monitors
(1) POWERGRID has appointed a panel of Independent External Monitors (IEMs) for this Pact with the approval of Central Vigilance Commission (CVC), Government of India. The names of the IEMs have been indicated in the Bidding Documents.
(2) The panel of IEMs shall review independently and objectively, whether and to what extent the parties comply with the obligations under this agreement. The panel of IEMs has right of access to all project documentation. The panel of IEMs may examine any complaint received by them and submit a report to Chairman-cum-Managing Director, POWERGRID, giving joint findings, at the earliest. The panel of IEMs may also submit a report directly to the CVO and the CVC, in case of suspicion of serious irregularities attracting the provisions of the PC Act.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
Integrity Pact Page 5 of 8
(3) The IEM is not subject to instructions by the representatives of the parties and performs his functions neutrally and independently. He/She reports to the Chairman-cum-Managing Director, POWERGRID.
(4) The Bidder(s)/Contractor(s) accepts that the IEM has the right to access without restriction to all documentation of POWERGRID related to this contract including that provided by the Contractor/Bidder. The Bidder/Contractor will also grant the IEM, upon his/her request and demonstration of a valid interest, unrestricted and unconditional access to their documentation. The same is applicable to Subcontractors. The IEM is under contractual obligation to treat the information and documents of the Bidder(s)/Contractor(s)/Subcontractor(s) with confidentiality.
(5) POWERGRID will provide to the IEMs information as sought by him/her which could have an impact on the contractual relations between POWERGRID and the Bidder/Contractor related to this contract. The IEMs shall also sign declaration on 'Non-Disclosure of Confidential Information' and of 'Absence of Conflict of Interest'. In case of any conflict of interest arising at a later date, the IEM shall inform Chairman-cum-Managing Director, POWERGRID and rescue himself/herself from that case
(6) As soon as the IEM notices, or believes to notice, a violation of this agreement, he/she will so inform the Chairman-cum-Managing Director, POWERGRID and request the Chairman-cum-Managing Director, POWERGRID to discontinue or take corrective action, or to take other relevant action. The IEM can in this regard submit non-binding recommendations. Beyond this, the IEM has no right to demand from the parties that they act in a specific manner, refrain from action or tolerate action. However, the IEM shall give an opportunity to POWERGRID and the Bidder/Contractor, as deemed fit, to present its case before making its recommendations to POWERGRID.
(7) The IEM will submit a written report to the Chairman-cum-Managing Director, POWERGRID within 8 to 10 weeks from the date of reference or intimation to him by POWERGRID and, should the occasion arise, submit proposals for correcting problematic situations.
(8) If the IEM has reported to the Chairman-cum-Managing Director, POWERGRID, a substantiated suspicion of an offence under PC/IPC Act, and the Chairman-cum-Managing Director, POWERGRID has not, within the reasonable time taken visible action to proceed against such offence or reported it to the CVO, the Monitor may also transmit this information directly to the CVC, Government of India.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
Integrity Pact Page 6 of 8
(9) While representing any matter in relation to the Integrity pact inter-alia including its transgression to the panel of IEMs, POWERGRID and Bidder/Contractor shall not approach the court of law and await the decision of the IEM in the matter.
(10) The word ‘IEM’ would include both singular and plural.
(*) This Section shall be applicable for only those packages wherein the IEMs have been identified in Section – I : Invitation for Bids and/or Clause ITB 9.3 in Section – III: Bid Data Sheets of Conditions of Contract, Volume-I of the Bidding Documents.
Section IX - Pact Duration
This Pact begins when both parties have legally signed it. It expires for the Contractor after the closure of the contract and for all other Bidder's six month after the contract has been awarded.
Section X - Other Provisions
(1) This agreement is subject to Indian Law. Place of performance and jurisdiction is the establishment of POWERGRID. The Arbitration clause provided in the main tender document / contract shall not be applicable for any issue / dispute arising under Integrity Pact.
(2) Changes and supplements as well as termination notices need to be made in writing. Side agreements have not been made.
(3) If the Contractor is a partnership firm or a consortium or Joint Venture, this agreement must be signed by all partners, consortium members and Joint Venture partners.
(4) Nothing in this agreement shall affect the rights of the parties available under the General Conditions of Contract (GCC) and Special Conditions of Contract (SCC).
(5) Issues like Warranty/Guarantees etc. shall be outside the purview of IEMs.
(6) Views expressed or suggestions/submissions made by the parties and the recommendations of the CVO/IEM# in respect of the violation of this agreement, shall not be relied on or introduced as evidence in the arbitral or judicial proceedings (arising out of the arbitral proceedings) by the parties in connection with the disputes/differences arising out of the subject contract.
# CVO shall be applicable for packages wherein IEM are not identified in Section IFB/BDS of Condition of Contract, Volume-I. IEM shall be applicable for packages wherein IEM are identified in Section IFB/BDS of Condition of Contract, Volume-I.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
Integrity Pact Page 7 of 8
(7) Should one or several provisions of this agreement turn out to be invalid, the remainder of this agreement remains valid. In this case, the parties will strive to come to an agreement to their original intentions.
Signature Signature
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Partner(s) of Joint Venture/ Contractor)
(Office Seal) (Office Seal)
Designation : Designation :
Witness 1 : Witness 1 :
Designation : Designation :
Witness 2 : Witness 2 :
Designation : Designation :
Integrity Pact Page 8 of 8
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-15
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
Option for Initial Advance (either Interest Bearing Initial Advance or No Initial Advance) and Information for E – payment, PF details and declaration for Micro/Small and Medium Enterprise
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
I We have read the provisions in the Bidding Documents regarding furnishing the option for advance payment. Accordingly, as per ITB Clause 9.3 as provided in Section BDS, Section III, Vol.-I of the Bidding Documents, we hereby confirm to opt the following:
Interest Bearing Initial Advance
Supply Portion:
Services Portion:
I We are furnishing the following details of Statutory Registration Numbers and details of Bank for electronic payment.
1. Name of the Supplier/ Contractor in whose favour payment is to be made 0
2. Address with PIN Code and State
Registered Office:
Correspondence Address:
3. (a) Status – Company/others
[Declaration of Micro/ Small/ Medium Enterprise under Micro/ Small & Medium Enterprises Development Act 2006, if applicable]
3. (b) Are you a MSE owned by SC/ST* entrepreneurs in line with Public Procurement Policy for Micro and Small Enterprises (MSEs) order 2012 including subsequent amendment/notification/order (Indicate Yes/No) Note: Documentary evidence is to be attached. Please refer remarks at the end of the attachment. No
3. (c ) If 3(b) is ‘Yes’ please mention whether you are (Proprietary MSE/ Partnership MSE/ Private Limited Company) owned by SC/ST entrepreneurs
3. (d ) Are you a MSE owned by women in line with Public Procurement Policy for Micro and Small Enterprises (MSEs) order 2012, Public Procurement Policy for Micro and Small Enterprises (MSEs) Amendment order 2018 including subsequent amendment/notification/order (Indicate Yes/No) Note: Documentary evidence is to be attached.
4. Permanent Account (PAN) No.
5. GSTIN Numbers
I. GSTIN in the Sates/UT from where the supply of goods take place
Name of the States/UT GSTIN number
II. GSTIN in the States/UT where the supply for services take place (states where sites under the subject package is situated)
Name of the States/UT GSTIN number
6 PF Registration No. of the Company
7 PF Regional Office covered (with Address)
8 Name of Contact Person
9 Contact Details
10 Bank Details for Electronic Payment
Name of the Bank:
Address of Branch:
Type of Account:
Type of Account: Current Account
11 9 digit MICR code printed at bottom in middle, next to cheque no.
12 IFSC (for RTGS)/NEFT Code (to be obtained from the Bank) Sample Cancelled Cheque to be enclosed
We hereby declare that the above information are true and correct and we agree that the payment on account of this Contract, in the event of award, be made in the above account maintained in the above mentioned Bank.
*The definition of MSEs owned by SC/ST is as given under:
a. In case of proprietary MSE, proprietor(s) shall be SC /ST.
b. In case of partnership MSE, the SC/ST partners shall be holding at least 51% shares in the unit.
c. In case of Private Limited companies, at least 51% share shall be held by SC/ST promoters.
Documentary evidence: Please provide scanned copy(ies) of the SC/ST certificate(s) issued by District Authority as applicable for SC/ST MSE category as per (a), (b) or (c) above.
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-16
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Additional Information)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
In support of the additional information required as per ITB Sub-Clause 9.3 (q) of the Bidding Documents, we furnish herewith our data/details/documents etc., alongwith other information, as follows (the stipulations have been reproduced in italics for ready reference):
1.0 The Bidder shall furnish
A certificate from their Banker(s) (as per prescribed formats in Form 16, Section-VI: Sample Forms and Procedures) indicating various fund based/non fund based limits sanctioned to the Bidder and the extent of utilization as on date. Such certificate should have been issued not earlier than three months prior to the date of bid opening. Wherever necessary the Employer may make queries with the Bidders’ Bankers. [Reference ITB clause 9.3(q)(i)]
1.1 In accordance with 1.0, certificate(s) from banker as per requisite format, indicating various fund based/non fund based limits sanctioned to the bidder or each member of the joint venture and the extent of utilization as on date is/are enclosed, as per the following details:
Name of the Bidder (Sole Bidder) 0
Name of the Banker by whom certificate issued
Date of certificate (should not be earlier than 3 months prior to date of bid opening)
Whether fund based/non fund based limits are indicated in the certificate
Whether extent of utilization is indicated in the certificate
1.2 The Bidder should accordingly also provide the following information/documents
(i) Details of Banker:
Address of Banker
Contact Name and Title
(ii) As per para 1.0, Authorization Letter(s) from the bidder (in case of JV bidder, from all the partners) addressed to the Banker(s), authorizing POWERGRID to seek queries about the bidder with the Banker(s) and advising the Banker(s) to reply the same promptly, is/are enclosed as per following details:
Sl. No. Letter Ref. Date Addressed to (name of the Bank)
(iii) As per para BDS/ITB clause 9.3q, Bidder shall furnish the details of their Provident Fund Code Number
Sl. No. Name of Bidders/JV Partners Provident Fund Code Number Details
2.0 Litigation History
The bidder should provide detailed information on any litigation or arbitration arising out of contracts completed or under execution by it over the last five years. A consistent history of awards involving litigation against the Bidder or any partner of JV may result in rejection of Bid. [Reference ITB clause 9.3(q)(ii)]
2.1 Details of litigation history resulting from Contracts completed or under execution by the bidder over the last five years
Year Name of client, cause of litigation/arbitration and matter in dispute Details of Contract and date Award for or against the bidder Disputed amount
3.0 Details regarding previous transgressions of Integrity Pact
The bidder should provide detailed information on any transgression of Integrity Pact that occurred in the last 10 years with any other Public Sector Undertaking or Government Department or any other Company, in any country.
3.1 Details regarding previous transgressions of Integrity Pact that occurred in the last 10 years
Year Name of client Details of Transgression of Integrity Pact by the bidder
4.0 OTHER INFORMATION
4.1 Current Contract Commitments of works in progress
Bidders (individual firms or each partners of JV) should provide information on their current commitments on all contracts that have been awarded, or for which a letter of intent or acceptance has been received, or for contracts approaching completion, but for which an unqualified, full completion certificate has yet to be issued.
Details of Contract Value of outstanding work (Rs.) Estimated completion date
4.2 Financial Data:
Details Actual (Previous five years) Projection for next five years
Total Liability
Current Liability
Profit before taxes
Profit after taxes
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-17
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Declaration for tax exemptions, reductions, allowances or benefits)
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
1 We confirm that we are solely responsible for obtaining following tax exemptions, reductions, allowances or benefits in respect of supplies under the subject package, in case of award. We further confirm that we have considered the same in our bid thereby passing on the benefit to POWERGRID while quoting our prices. In case of our failure to receive such benefits, partly or fully, for any reason whatsoever, the Employer will not compensate us.
2 We are furnishing the following information required by the Employer for issue of requisite certificate if and as permitted in terms of the applicable Govt. of India policies/procedures (in case of award):
Applicable Act, Notification No. and Clause Ref. No. Sl. No. Description of item on which applicable Country of origin Remarks, if any
(The requirements listed above are as per current Notification of Govt. of India indicated above. These may be modified, if necessary, in terms of the Notifications.)
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-17
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Information regarding Ex-employees of POWERGRID in our Organisation)
Name(s) and Addresse(s) of other partner(s) To:
Contract Services
Name : …… ……. …….. …… ……. …….. Power Grid Corporation of India Ltd.,
Address : …… ……. …….. …… ……. …….. "Saudamini", Plot No. 2, Sector 29
We hereby furnish the details of ex-employees of POWERGRID who had retired/ resigned at the level of General Manager and above from POWERGRID and subsequently have been employed by us:
Sl. No. Name of the person with designation in POWERGRID Date of Retirement/ resignation from POWERGRID Date of joining and designation in our organisation
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-17
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
(Information regarding Ex-employees of POWERGRID in our Organisation)
Name(s) and Addresse(s) of other partner(s) To:
Contract Services
Name : Power Grid Corporation of India Ltd.,
Address : "Saudamini", Plot No. 2, Sector 29
Gurgaon (Haryana) - 122001
We hereby furnish the details of ex-employees of POWERGRID who had retired/ resigned at the level of General Manager and above from POWERGRID and subsequently have been employed by us:
Sl. No. Name of the person with designation in POWERGRID Date of Retirement/ resignation from POWERGRID Date of joining and designation in our organisation
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-18
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
Safety Pact is attached herewith this Volume
Date : -- Printed Name :
Place : Designation :
Instruction for printing & submitting Safety Pact
1. The requisite format of Safety Pact is getting generated automatically and displayed here below.
2. Take print out of first page on a non-judicial stamp paper of Rs. 100/- and other six pages on plain A4 size paper. Such two sets shall be prepared by the bidder.
3. All the pages of both the copies of the Safety Pact shall be signed by the authorised representative of the bidder and duly stamped.
4. Both the original copies shall be submitted by the bidder in the form of Hard Copy as part of the first envelope before due date & time of submission of the bid.
5. For further details bidders may please refer ITB Clause 9.3 (s).
Between #REF! #REF!
Power Grid Corporation of India Limited #REF! #REF!
having its Registered Office at B-9, Qutab Institutional Area, Katwaria Sarai, New Delhi – 110016 hereinafter referred to as #REF! #REF!
"POWERGRID", #REF! #REF!
0 1 having its Registered Office at ,
having its Registered Office at ,, 1 AND
hereinafter referred to as
"The Bidder/Contractor"
POWERGRID intends to award, under laid-down organisational procedures, contract(s) for Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation. Specification Number:5002002317/OTHERS/DOM/A06-CC CS -7
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Contractor)
Safety Pact Page 1 of 6
POWERGRID values full compliance with all relevant laws and regulations and the principles of Safety, Health& Environment in its relations with its Bidders/ Contractors.
In order to achieve these goals, POWERGRID and the above named Bidder / Contractor enter into this agreement called “Safety Pact” which will form part of the Bid.
It is hereby agreed by and between the parties as under:
Section I - Commitments of POWERGRID
POWERGRID commits itself to take all measures necessary to prevent accidents duringConstruction and Operation of the Transmission Assets and to observe the following:
1. POWERGRID recognizes and accepts its statutory responsibilities for ensuring construction, operation and maintenance of equipments and for the provision of safe methods of work and safe working conditions.
2. POWERGRID recognizes and accepts its statutory responsibilities for ensuring safety of not only its employees but also that of the Contracting Agencies as Principal Employer.
3. POWERGRID shall review the accidents in a structured manner and take necessary actions to ensure that the safety criteria are strengthened for safe construction as well as Operation & Maintenance of the Transmission Assets.
4. POWERGRID shall conduct necessary awareness and training programmes to its Employees to augment the various safety requirements to be followed during Construction and Operation & Maintenance of the Transmission Assets from time to time.
5. POWERGRID shall, from time to time, issue necessary guidelines,instructions and deterrents to its employees as well as to the Contracting Agencies, to update them to take necessary preventive measures to avoid repetition of similar accident attributes.
6. POWERGRID shall review and provide necessary guidanceto the Contracting Agencies, as and when, any abnormality / special situations are brought to its notice by the Contracting Agencies during execution of the Transmission Projects being executed by them.
7. POWERGRID shall conduct periodical surveillance site inspections / audits to identify the unsafe conditions and unsafe actions, and bring them to the knowledge of the Contracting Agencies for taking timely corrective actions.
8. POWERGRIDshall investigate all accidents, fatal as well as non-fatal, to identify the lapses, the reason for the accident / incident and suggest measures for prevention of recurrence of such accidents, and fix responsibility for the lapses leading to the accident.
9. POWERGRID shall augment the training to the workers and supervising personnel of the Contracting Agencies, as per schedules, upon nomination by the Contracting Agencies in reasonable time frame.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Contractor)
Safety Pact Page 2 of 6
10. POWERGRID shall exercise the right to claim and recover compensation from the Contracting Agencies in case of any violation of the safety requirements / provisions during execution of the Transmission Projects, as built in the applicable Laws and contractual specifications / guidelines in vogue / issued by POWERGRID from time to time.
Section II – Commitments of the Bidder / Contractor:
The Bidder / Contractor commits himself to take all measures necessary to prevent / minimise accidents at their construction / erection sites and to observe the following:
1. The Bidder / Contractor recognizes and acceptsthe statutory and comprehensive responsibility for ensuring safe construction and Testing & Commissioning in the Transmission Projects being executed by them by providing safe methods of work, working conditions and Tools & Plants for human safety.
2. The Bidder / Contractor recognizes and accepts the responsibilities for ensuring safety of not only their employees but also that of the Sub-contractors, Principal Employer and the general public during execution of the Transmission Projects / works.
3. The Bidder / Contractor shall review the accidents in a structured manner and take necessary actions to ensure that the safety criteria are strengthened for safe construction of the Transmission Assets.
4. The Bidder / Contractor shall endeavour continuous development of safe methods of work to ensure that the effect of risks and perils are minimised to the extent possible and implement the same at their worksites.
5. The Bidder / Contractor shall conduct periodical Training to their Employees as well as to that of their Sub-contractors for safety awareness during construction works being executed by them.
6. The Bidder / Contractor shall provide all requisite Tools & Plants required for the work and ensure their healthiness by periodical inspections / testing as required. Unhealthy and sub-standard Tools & Plants will be immediately removed from site as and when they are identified.
7. The Bidder / Contractor shall,at their cost, provide all necessary Personal Protective Equipments such as Double Lanyard Safety Belts, Appropriate Fall Arrest Systems, Safety Helmets, Foot Wear, Hand Gloves, etc., as required for various activities pertaining to execution of the Projects / works, confirming to relevant Indian Standards.
8. The Bidder / Contractor shall ensure that dedicated qualified Safety Officers are posted in the construction projects being executed by them and ensure that the Safety Officer visits each and every gang periodically and conducts audits / inspections to identify the unsafe conditions and unsafe actions, to be rectified by the site supervising personnel promptly.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Contractor)
Safety Pact Page 3 of 6
9. The Bidder / Contractor shall conduct appropriate medical checks-up for the workers before deploying them at their construction sites to ensure that only those who are medically fit are deployed in the Projects / works to be executed by them. The copy of the Medical Reports shall be provided by the Bidder / Contractor to POWERGRID, whenever requested by POWERGRID.
10. The Bidder / Contractor shall screen the workers before deploying them at their construction sites to ensure that only those with the skills, experience and competence to work at height and also medically fit for work at height are deployed for work at height in the Projects executed by them.
11. The Bidder / Contractor shall ensure daily before starting the work that their site Supervising Personnel / Safety Officer briefs the workers about the work for the day and the safety measures / precautions required to be taken by them.
12. The Bidder / Contractor shall investigate all the accidents at their working sites to ascertain the lapses leading to the incident and the precautionary / corrective measures required to be taken to avoid recurrence of such accidents. These accidents will be reviewed at the Board Management level of the Agencies and the findings / recommendations will be put up to POWERGRID Apex Safety Board within the stipulated period.
13. The Bidder / Contractor shall ensure that all accidents, whether fatal or non-fatal in nature, will be informed to POWERGRID, in writing, immediately on the occurrence of the same,and in any case, within not more than 24 hours of occurrence of the same.
14. The Bidder / Contractor shall ensure that in case of any accident, all necessary medical help / support shall be provided to the victims / injured till they are completely fit to return to work.
15. The Bidder / Contractor shall ensure that in case of fatal accidents, all statutory Authorities, including Police, concerned Labour Dept. Officials, concerned Workmen Compensation Commissioner, etc., will be intimated in writing as required by the statutory Law, and followed up for compliance of all statutory obligations. The Bidder / Contractor shall own full responsibility of timely accident reporting to various authorities, including POWERGRID.
16. The Bidder / Contractor shall ensure that in case of fatality or serious injury leading to permanent disablement of the victims, the compensation amount will be deposited with the concerned authorities, as required by the Laws, and followed up for early disbursement to the beneficiaries of the victims.
17. The Bidder / Contractor assures that they shall co-operate to the fullest extent for carrying out any investigation of the accidents at their work sites by POWERGRID to identify the lapses, the reason for the accident / incident and suggest measures for prevention of recurrence of such accidents. All factual details of the occurrence of the accident will be provided to POWERGRID, as and when required.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Contractor)
Safety Pact Page 4 of 6
18. The Bidder / Contractor assures that they take full responsibility of meeting the statutory obligations in case of accidents, and in case of any reference by any Statutory Body at a later date also, they shall provide all information to POWERGRID and meet all the statutory obligations, including payment of additional compensation, if any.
19. The Bidder / Contractor assures that in case of any inspection of their work site or Notice by any Statutory Authority, they shall comply promptly and inform POWERGRID Site Officials of the same, and also provide all necessary information and assistance for smooth compliance of the observations / instructions of such Authorities.
20. The Bidder / Contractor accepts the provisions regarding safety, including payment of any sums to POWERGRID, in case of any violation of the safety requirements / provisions during execution of the Transmission Projects, as built in the Contractual Conditions, Safety Planand the Safety Pact, and confirm to abide by the same.
Section III – Equal treatment to all Bidders / Contractors:
1. POWERGRID will enter into agreements with identical conditions as this one with all Bidders.
2. POWERGRID will disqualify, from the tender process, any bidder/ take punitive actions on the bidder, who does not sign this Pact or violate its provisions.
Section IV – Pact Duration:
This Pact begins when both parties have legally signed it. It expires for the successful Bidder / Contractor after closure of the contract and, for all other Bidders, after the contract has been awarded.
Section V – Other Provisions:
1. This agreement is subject to Indian Law. Place of performance and jurisdiction is the establishment of POWERGRID. The Arbitration clause provided in the main tender document / contract shall not be applicable for any issue / dispute arising under the Safety Pact.
2. Changes and supplements need to be made in writing, which shall come into force only upon mutual agreement / acceptance.
3. If the Contractor is a partnership firm or consortium of Joint Venture, this agreement must be signed by all partners, consortium members and Joint Venue partners, as applicable as per the Tender Specifications.
4. Nothing in this agreement shall affect the rights of the parties available under General Conditions of Contract (GCC) and Special Conditions of Contract (SCC).
5. Should one or several provisions of this agreement turn out to be invalid, the reminder of this agreement remains valid. In this case, the parties will strive to come to an agreement to their original intentions.
(Signature) (Signature)
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Contractor)
Safety Pact Page 5 of 6
Signature Signature
(For & On behalf of POWERGRID) (For & On behalf of Bidder/ Contractor)
(Office Seal) (Office Seal)
Designation : Designation :
Witness 1 : Witness 1 :
Designation : Designation :
Witness 2 : Witness 2 :
Designation : Designation :
Safety Pact Page 6 of 6
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Attachment-19
Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation.
Bidder’s Name and Address : To:
Contract Services
Name : 0 Power Grid Corporation of India Ltd.,
Address : 0 "Saudamini", Plot No. 2, Sector 29
0 Gurgaon (Haryana) - 122001
Further, we hereby confirm that except as mentioned in the Attachment – 6 (Alternative, Deviations and Exceptions to the Provisions) hereof forming part of our First Envelope :
Date : -- Printed Name :
Place : Designation :
Specification No. :5002002317/OTHERS/DOM/A06-CC CS -7 Bid Form 1st Envelope 1 one 1 st 1 January
2 two 2 nd 2 February
BID FORM (First Envelope) 3 three 3 rd 3 March
4 four 4 th 4 April
Bid Proposal Ref. No. 5 five 5 th 5 May
Date : -- 6 six 6 th #VALUE! 6 June
7 seven 7 th #VALUE! 7 July
To: 8 eight 8 th #VALUE! 8 August
Contract Services 9 nine 9 th #VALUE! 9 September
Power Grid Corporation of India Ltd., 10 ten 10 th 10 October
"Saudamini", Plot No. 2, Sector 29 11 eleven 11 th 11 November
Gurgaon (Haryana) - 122001 12 twelve 12 th 12 December
13 thirteen 13 th
14 fourteen 14 th
Name of Contract : Package DC-1 for Construction & Interiors of Green Field Data Centre Building at Manesar under Establishment of Pilot Data Centre at POWERGRID Manesar substation. 15 fifteen 15 th
Dear Ladies and/or Gentlemen, Enter details here. 16 sixteen 16 th
1.0 Having examined the Bidding Documents, including Amendment Nos. dated …[Enter the Date in dd-mm-yyyy]… the receipt of which is hereby acknowledged, we the undersigned, offer to design, manufacture, test, deliver, install and commission (including carrying out Trial operation, Performance & Guarantee Test as per the provision of Technical Specification) the Facilities under the above-named package in full conformity with the said Bidding Documents. In accordance with ITB Clause 9.1 of the Bidding Documents, as per which the bid shall be submitted by the bidder under “Single Stage - Two Envelope” procedure of bidding. Accordingly, we hereby submit our Bid, in two envelopes i.e. First Envelope – Techno – Commercial Part & Second Envelope - Price Part (to be opened subsequently). …[Enter the Date in dd-mm-yyyy]… the receipt of which is hereby acknowledged, we the undersigned, offer to design, manufacture, test, deliver, install and commission (including carrying out Trial operation, Performance & Guarantee Test as per the provision of Technical Specification) the Facilities under the above-named package in full conformity with the said Bidding Documents. In accordance with ITB Clause 9.1 of the Bidding Documents, as per which the bid shall be submitted by the bidder under “Single Stage - Two Envelope” procedure of bidding. Accordingly, we hereby submit our Bid, in two envelopes i.e. First Envelope – Techno – Commercial Part & Second Envelope - Price Part (to be opened subsequently). 17 seventeen 17 th
1.1 We meet the eligibility requirements and have no conflict of interest in accordance with ITB Clause 2.
2.0 Attachments to the Bid Form (First Envelope) Bank Draft 18 eighteen 18 th
In line with the requirement of the Bidding Documents, we enclose herewith the following Attachments: Enter details here. Bid Security Currency Amount Validity Pay Order 19 nineteen 19 th
Or Online Payment Acknowledgement towards Bid Security for a sum of ................................................ (name of currency and amount in words and figures)
or documentary evidence in support of exemption of Bid Security, in separate envelope in accordance with clause 21 of ITB, Section-II." Please note that if bid validity is less than 250 days, your bid may be rejected
(b) Attachment 2(Package DC-1 ) : A power of attorney duly authorized by a Notary Public indicating that the person(s) signing the bid have the authority to sign the bid and thus that the bid is binding upon us during the full period of its validity in accordance with the ITB Clause 14. Bank Guarantee (0) 21 st
(c) Attachment 3(Package DC-1 ) : The documentary evidence that we are eligible to bid in accordance with ITB Clause 2. Further, in terms of ITB Clause 9.3(c) & (e), the qualification data has been furnished as per your format enclosed with the bidding documents [Attachment – 3(QR)]. 22 th
Further, the required Joint Venture Agreement signed by us and our Partners has also been furnished as per your format Attachment-3(JV). #REF! Applicable 23 th
Further the required deed of Joint Undertaking signed by us and Tower Manufacturer has also been furnished as per your format. 0 #REF! Not Applicable 24 th
(d) Attachment 4(Package DC-1 ) : The documentary evidence establishing in accordance with ITB Clause 3, Vol.-I of the Bidding Documents that the facilities offered by us are eligible facilities and conform to the Bidding Documents has been furnished as Attachment 4. A list of Special Tools & Tackles to be used by us for erection, testing & Commissioning and to be handed over to Employer, the cost of which is included is our Bid Price, is also enclosed as per your format as Attachment 4A. A list of Special Tools & Tackles to be brought by the contractor for erection, testing & Commissioning and to be taken back after completion of work, whose cost in not included in our bid price, is enclosed as per your format as Attachment 4B. 25 th
(e) Attachment 5(Package DC-1 ) : The details of all major items of services or supply which we propose subletting in case of award, giving details of the name and nationality of the proposed subcontractor/sub-vendor for each item. 26 th
(f) Attachment 5A(Package DC-1 ) : Items, Components, Raw Material, Services proposed to be sourced from Micro and Small Enterprises. 26 th
(g) Attachment 6(Package DC-1 ) : The variation and deviations from the requirements of the Conditions of Contract, Technical Specification and Drawings (excluding critical provisions as mentioned at clause 6.0 below) in your format enclosed with the Bidding Documents, including, inter alia, the cost of withdrawal of the variations and deviations indicated therein. 27 th
(h) Attachment 7(Package DC-1 ) : The details of Alternative Bids made by us indicating the complete Technical Specifications and the deviation to contractual and commercial conditions. (Not Applicable) 28 th
(i) Attachment 8(Package DC-1 ) : Manufacturer’s Authorisation Forms. 29 th
(j) Attachment 9(Package DC-1 ) : Work Completion Schedule. 30 th
(k) Attachment 10(Package DC-1 ) : Guarantee Declaration. 31 st
(l) Attachment 11(Package DC-1 ) : Information regarding ex-employees of Employer in our firm.
(m) Attachment 12(Package DC-1 ) : Filled up information regarding Price Adjustment Data as per the format enclosed in the bidding documents.
(n) Attachment 13(Package DC-1 ) : Declaration regarding Social Accountability.
(o) Attachment 14(Package DC-1 ) : Integrity Pact, in a separate envelope, duly signed on each page by the person signing the bid.
(p) Attachment 15(Package DC-1 ) : Option for Initial Advance (either Interest Bearing Initial Advance or No Initial Advance) and Information for E – payment, PF details and declaration for Micro/Small and Medium Enterprise
(q) Attachment 16(Package DC-1 ) : Additional Information.
(r) Attachment 17(Package DC-1 ) : Declaration for tax exemptions, reductions, allowances or benefits
(s) Attachment 18(Package DC-1 ) : Safety Pact
(t) Attachment 19(Package DC-1 ) : Declaration.
(u) Attachment 20(Package DC-1 ) : Declaration of Key Managerial Person jointly with Power of Attorney holder
(v) Attachment 21(Package DC-1 ) : Affidavit of Self certification regarding Minimum Local Content in line with PPP-MII order and MoP Order, if applicable
(w) Attachment 22(Package DC-1 ) : Certificate from statutory auditor or cost auditor of the company (in the case of companies) or from a practicing cost accountant or practicing chartered accountant (in respect of suppliers other than companies) giving the percentage of Local Content, in line with PPP-MII order and MoP Order, if applicable
(x) Attachment 23(Package DC-1 ) : Authorization certificate issued by Domestic Manufacturer for selling Domestically Manufactured Iron & Steel Products
(y) Attachment 24(Package DC-1 ) : Affidavit of Self certification regarding Domestic Value Addition in Iron & Steel Products
(z) Attachment 25(Package DC-1 ) : Compliance to the process related to the e-RA Terms & Conditions and the Business Rules governing the e-RA
(aa) Attachment 26(Package DC-1 ) : Declaration by the Bidder regarding events encountered pursuant to ITB Clause 2.1
(ab) Attachment 27(Package DC-1 ) : Certification by the Bidder per DoE Order in line with ITB Clause 2.1(In case of a Joint Venture bid, the declaration/ certification shall be given by all partners of the Joint Venture)
3.0 We are aware that, in line with Clause No. 27.1 (ITB), our Second Envelope (Price Part) is liable to be rejected in case the same contains any deviation/omission from the contractual and commercial conditions and technical Specifications other than those identified in this First Envelope.
4.0 We confirm that except as otherwise specifically provided our Bid Prices in Second Envelope include all taxes, duties, levies and charges as may be assessed on us, our Sub-Contractor/Sub-Vendor or their employees by all municipal, state or national government authorities in connection with the Facilities, in and outside of India.
4.1 100% of applicable Taxes and Duties i.e. GST, which are payable by the Employer under the Contract, shall be reimbursed by the Employer on production of satisfactory documentary evidence by the Contractor in accordance with the provisions of the Bidding Documents.
4.3 We confirm that we have also registered/we shall also get registered in the GST Network with a GSTIN, in all the states where the project is located and the states from which we shall make our supply of goods.
5.0 Construction of the Contract
5.1 We declare that we have studied Clause GCC 2.1 relating to mode of contracting for Domestic Bidders and we are making this proposal with a stipulation that you shall award us two separate Contracts viz ‘First Contract’ for ex-works supply of all equipment and materials including mandatory spares and ‘Second Contract’ for providing all the services i.e. inland transportation for delivery at site, In-transit insurance, unloading, handling at site, installation, testing and commissioning including Trial operation in respect of all the equipment supplied under the ‘First Contract’ and other services specified in the Contract Documents. We declare that the award of two contracts, will not, in any way, dilute our responsibility for successful operation of plant/equipment and fulfillment of all obligations as per Bidding Documents and that both the Contracts will have a cross-fall breach clause i.e. a breach in one Contract will automatically be classified as a breach of the other contract which will confer on you the right to terminate the other contract at our risk and cost.
6.0 We have read the provisions of following clauses and confirm that the specified stipulations of these clauses are acceptable to us:
(a) ITB 13 Bid Security
(b) GCC 2.14 Governing Law
(c) GCC 5.1 Contractor’s Responsibilities
(d) GCC 8 Terms of Payment
(e) GCC 9.3 Performance Security
(f) GCC 10 Taxes and Duties
(g) GCC 21.2 Completion Time Guarantee
(h) GCC 22 Defect Liability
(i) GCC 23 Functional Guarantee
(j) GCC 25 Patent Indemnity
(k) GCC 26 Limitation of Liability
(l) GCC 38 Settlement of Disputes
(m) GCC 39 Arbitration
(n) Appendix 2 to Form of Contract Agreement Price Adjustment
Further we understand that deviation taken in any of the above clauses by us may make our bid non-responsive as per provision of bidding documents and be rejected by you.
7.0 We undertake, if our bid is accepted, to commence the work immediately upon your Notification of Award to us, and to achieve the delivery of goods and related services within the time stated in the Bidding Documents.
8.0 If our bid is accepted, we undertake to provide a Performance Security in the form and amounts, and within the times specified in the Bidding Documents.
9.0 We agree to abide by this bid for a period of six (06) months from the date fixed for opening of bids as stipulated in the Bidding Documents, and it shall remain binding upon us and may be accepted by you at any time before the expiration of that period.
10.0 Until a formal Contract is prepared and executed between us, this bid, together with your written acceptance thereof in the form of your Notification of Award shall constitute a binding contract between us.
11.0 We understand that you are not bound to accept the lowest or any bid you may receive.
12.0 # (For Joint Venture only) We, the partners of Joint Venture submitting this bid, do agree and confirm that in case of Award of Contract on the Joint Venture, we shall be jointly and severally liable and responsible for the execution of the Contract in accordance with Contract terms and conditions. 2
13.0 We are a Micro and Small Enterprise (MSE) registered with , a designated Authority of GoI under the Public Procurement Policy for MSEs order 2012, Notification dated 01/06/2020 and 26/06/2020 read in conjuction with related notifications issued from time to time for such enterprises. 2
14.0 We, hereby, declare that only the persons or firms interested in this proposal as principals are named here and that no other persons or firms other than those mentioned herein have any interest in this proposal or in the Contract to be entered into, if the award is made on us, that this proposal is made without any connection with any other person, firm or party likewise submitting a proposal is in all respects for and in good faith, without collusion or fraud.
Thanking you, we remain,
Yours faithfully,
For and on behalf of 0
Date : -- Printed Name :
Place : Designation :
In case of bid from a Joint Venture, name & designation of representative of JV partner is to be provided and Bid Form is also to be signed by him
#REF! Printed Name :
#REF! Designation :
Please provide additional information of the Bidder
Business Address :
Country of Incorporation :
State/Province to be indicated :
Name of Principal Officer :
Address of Principal Officer :
23 Twenty Three
27 Twenty Seven
28 Twenty Eight
33 Thirty Three
37 Thirty Seven
38 Thirty Eight
73 Seventy Three
74 Seventy Four
75 Seventy Five
77 Seventy Seven
78 Seventy Eight
79 Seventy Nine
83 Eighty Three
87 Eighty Seven
88 Eighty Eight
93 Ninety Three
97 Ninety Seven
98 Ninety Eight
100 One Hundred
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html
Price_schedule.xlsx
xlsx • 0.67 MB
First_Envelope_and_Bid_Forms.xlsx
xlsx • 1.66 MB
00_Cover Pages Vol-III.doc
doc • 0.82 MB
01_Attachment-8_Manufacturer Authorization Form.doc
doc • 0.03 MB
02_Attachment-20_KMP Declaration.doc
doc • 0.04 MB
03_Attachment-21_Affidavit for Self-Certification-PPP-MII.DOCX
docx • 0.02 MB
04_Attachment-22_Certificate by Auditor-PPP-MII.docx
docx • 0.02 MB
05_Attachment-23-Authorization Certificate issued by Domestic Manufacturer.docx
docx • 0.02 MB
06_Attachment-24-Affidavit for Self Certification-Iron & Steel.docx
docx • 0.02 MB
07_Attachment-25_Compliance to the process related to the e-RA.docx
docx • 0.02 MB
08_Attachment-26_Declaration regarding events encountered pursuant to ITB Clause 2.1.docx
docx • 0.03 MB
09_Attachment 27- Certificate by Bidder.docx
docx • 0.02 MB
12_Legends for Units.pdf
pdf • 0.03 MB
BASEMENT FLOOR PLAN.pdf
pdf • 0.19 MB
ELEVATION (LEFT SIDE & FRONT).pdf
pdf • 0.08 MB
ELEVATION (RIGHT SIDE & REAR).pdf
pdf • 0.08 MB
FIFTH FLOOR PLAN.pdf
pdf • 0.44 MB
FIRST FLOOR PLAN.pdf
pdf • 0.44 MB
FOURTH FLOOR PLAN.pdf
pdf • 0.44 MB
GROUND FLOOR PLAN DWG.pdf
pdf • 0.30 MB
SECOND FLOOR PLAN.pdf
pdf • 0.29 MB
SECTION-AA.pdf
pdf • 0.26 MB
SECTION-BB.pdf
pdf • 0.27 MB
SECTION-XX.pdf
pdf • 0.13 MB
SITE PLAN DWG.pdf
pdf • 0.54 MB
SIXTH FLOOR PLAN.pdf
pdf • 0.26 MB
TERRACE FLOOR PLAN.pdf
pdf • 0.46 MB
THIRD FLOOR PLAN.pdf
pdf • 0.44 MB
.DS_Store
Ds store • 0.01 MB
COLUMN LAYOUT PLAN.pdf
pdf • 0.08 MB
FRAMING PLAN AT BASEMENT LEVEL.pdf
pdf • 0.16 MB
FRAMING PLAN AT FIFTH FLOOR LEVEL.pdf
pdf • 0.18 MB
FRAMING PLAN AT FIRST FLOOR LEVEL.pdf
pdf • 0.18 MB
FRAMING PLAN AT FOURTH FLOOR LEVEL.pdf
pdf • 0.23 MB
FRAMING PLAN AT GROUND FLOOR LEVEL.pdf
pdf • 0.23 MB
FRAMING PLAN AT SECOND FLOOR LEVEL.pdf
pdf • 0.23 MB
FRAMING PLAN AT SIXTH FLOOR LEVEL.pdf
pdf • 0.16 MB
FRAMING PLAN AT THIRD FLOOR LEVEL.pdf
pdf • 0.23 MB
_1.DS_Store
Ds store • 0.01 MB
00_Cover Pages Vol-II.doc
doc • 0.82 MB
Annexure-I_Special Condition for IGBC Building.pdf
pdf • 0.68 MB
Annexure-II_Standard FQP.pdf
pdf • 2.22 MB
Annexure-III_L2 Schedule.pdf
pdf • 0.39 MB
Annexure-IV_Indicative Make List.pdf
pdf • 0.56 MB
Annexure-V_Tender Drawing List.pdf
pdf • 0.49 MB
TS_Package DC-1.pdf
pdf • 0.75 MB
~$_Section-I Invitation for Bids (IFB).doc
doc • 0.00 MB
00_Cover Pages Vol-I.doc
doc • 0.82 MB
01_Main Index_Volume-I.pdf
pdf • 0.26 MB
02_Section-I Invitation for Bids (IFB).doc
doc • 0.08 MB
03 Section - II ITB SSTE S&I DCB-PRANIT-July 2021.pdf
pdf • 0.75 MB
04_Section-III Bid Data Sheets (BDS) SSTE -PRANIT.docx
docx • 0.07 MB
05_Annexure - A (BDS)_Package-DC1.doc
doc • 0.07 MB
06-Annexure-B(BDS)_Vol-I.docx
docx • 0.02 MB
07-Annexure-C(BDS)_Vol-I.docx
docx • 0.03 MB
08_Section -IV General Conditions of Contract (GCC).pdf
pdf • 0.76 MB
09_Section-V-Special Conditions of Contract (SCC).doc
doc • 0.17 MB
10_Appendix-I to Special Conditions of Contract (SCC).pdf
pdf • 0.22 MB
12-Section - VI Sample Forms and Procedures (SFP).doc
doc • 0.42 MB
Annulment_letter.pdf
pdf • 0.24 MB
OBD_EXTENSION_NOTICE_-2-.docx
docx • 0.01 MB
OBD_EXTENSION_NOTICE.docx
docx • 0.01 MB
Price_schedule_Rev2.xlsx
xlsx • 0.67 MB
OBD_EXTENSION_NOTICE.docx
docx • 0.01 MB
Price_schedule_Rev1.xlsx
xlsx • 0.67 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .