Repairs to sunken floor roofs joinery sanitary fittings plastering internal water supply and other misc works at EME Wksp Stn HQ MES staff qtr under AGE B/R II at GE (N) Ahmednagar

Amount

Dismantling of stone slabs and tiles of any descriptions or thickness in floors, approns etc laid and bedded in any mortor all as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises

Demolition of cement concrete (un-reinforced) in ground floors and paving not exc 15 cm thickness below or above ground level complete all as specified.

Taking down cement plaster of any thickness on brick/stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as directed

Taking down chowkats or frames not exc 1.50sqm with shutters (without taking off shutters from the frames) all as directed.

Taking down chowkats or frames exc 1.50sqm not exc 4.00sqm with shutters (without taking off shutters from the frames) all as directed.

Taking down shutters of any description exc 1 sqm but not exc 2 sqm each all as directed.

M&L for moorum/red bajri filling in floors or pavings, laid in trenches n.exc. 15cm thick , speread , levelld and rammed including watering complete all as specified and directed.

M & L for hard core of gauge n exc 63mm deposited spreading & levelling in layers n exc 15 cm thick watered & rammed to a true surface

M & L for PCC 1:4:8 type D-2 using 40mm graded aggregate as in sub base of floor 75mm thick

M&L for RCC 1:2:4 (Nominal Mix) B-1 (20 mm graded stone aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete

M&L for TMT bars 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in, Set in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge including demolition

Material and labour for joint free / rectified non skid ceramic coloured tiles as specified in PS, 8-10 mm thick as approved by GE (square / rectangular) size of tiles 300x300 mm, as in floor etc laid over and including screed bed 15 mm thick in cement mortar 1:6 set and jointed with white or coloured cement to match complete all as specified and as directed.

Material and labour for coloured glazed ceramic tiles digitally printed premium designer series of size of tiles 350x450 mm , 8-10 mm thick as approved by GE as in dado/skirting or on vertical surfaces, over and including 10 mm thick backing coat in cement mortar 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

Material and labour for machine cut Kota stone slab 20 to 25mm thick (minimum size 30cm x 45cm) as in flooring, laid over and incl cement screed bed 15mm thick in cement mortar 1:4, and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and granite polishing complete all as specified

Material and labour for rough dressed shahabad stone, 25 mm to 40 mm thick laid over and including 15 mm thick screed bed in cement mortar 1:6, laid and jointed pointed in cement mortar 1:3 all as directed.

Material and labour for joint free / rectified ceramic coloured tiles of size 600x600 mm as specified in PS, 8-10 mm thick as approved by GE (square / rectangular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm, as in floor etc laid over and including screed bed 15 mm thick in cement and sand mortar (1:6) set and jointed with white or coloured cement to match the shade of tiles etc complete all as specified and directed by Engineer-in-Charge

All as per Sl item No 18 (here-in-before) but on skirting / Dado.

Material and labour for 16 to 18 mm thick pre-polished granite stone slab of approved shade and colour Jet Black / Telephone Black as in top table, top of WHB, kitchen slab/platform, steps, gate pillars, cills etc or on vertical surfaces including vertical projection, full round moulding the edge laid over screed bed 15mm thick in cement and sand mortar (1:4) jointing & pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade of granite and rubbing polishing to achieve mirror finish etc complete all as specified and directed by Engineer-in-Charge

Material and labour for machine cut cudappah stone slab 20-25 mm thick over cement screed base, full round moulding the edge laid over and including 15 mm thick screed bed in cement and sand mortar (1:6), set and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed by Engineer-in-Charge

M & L for Chequred cement concrete tiles with pigment 25 cm x 25 cm x 25 mm thick, set, jointed and pointed in neat cement slurry as in floors over and including screed bed of 15 mm thickness in cement and sand mortar (1:6) etc complete all as specified and directed by Engineer-in-Charge

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.

Material and labour for second class hard-wood in scantlings clean sawn

Supply and fix pressed steel frames of size 105 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. all as directed.

All as per item No 25 above but pressed steel frames of size 125 mm X 60 mm

Supply and fix solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, all as directed.

Material and labour for filling in door frames in plain cement concrete, 1:2:4 type B0, using 12.5 mm graded aggregates all as directed.

M & L 2nd class softwood plain fillets square rectangular or triangular section clean sawn and fixed with nails or brads exc 13 and n.exc 25 sqcm complete all as specified

Material and labour for second class hard wood beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc.and removing old beads all as directed.

Supply and fix 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides all as directed.

Supply and fix Factory made single extruted WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other frames chowkat of size 45x85mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum and screw withdrawal strength of 2200 N (face) ( 1100 N (Edge), minimum compressive strength 58 N /mm², modulus of elasticity 900 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire resistant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-charge

Supply and fixing Factory made single extruted WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (face) ( 900 N (Edge), minimum compressive strength 50 N /mm², modulus of elasticity 850 N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire resistant and fixing with stainless steel butt hinges in position with MS hold fast/lugs/SS dash fasteners all as per Engineer-in-charge

Supply and fix 2nd class hard wood 35 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) all as directed.

All as per item No 34 above but 30 mm thick as in window or ventilators.with sash bars

Supply and fixing Factory Made Solid PVC Moulded Door Shutter, with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face

Supply and fix steel windows with side hung double shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded all as directed.NOTES: 1) Guard bars shall be measured and paid separately as supply only. 2) M & L for galzing shall be measured and paid separately.

Supply and fix steel ventilator with top hung shutter including hinges, steel peg stay all as directed.NOTES: 1) Guard bars shall be measured and paid separately as supply only. 2) M & L for galzing shall be measured and paid separately.

Supply and fixing powder coated aluminium door shutters with frame in two panels made of section 47.5x44.45x2.25mm @1.12 kg/RM frame, vertical styles of section 47x44.5x2.75mm thick @ 1.15kg per RM, top rail & lock rail of section 47.5x44.5x2.75mm @ 1.33 kg per RM, bottom rail made of section 114.6x44.45x2.3mm@ 2.06 kg per RM with securing rebate @ 0.102 kg per RM with & incl 5mm thick plain sheet glass incl necessary screw, jointing cleats, glazing clip, rubber packing, aluminium snap beeding complete all as specified and directed.

Supply and fix power coated aluminium three track window made out of Jindal aluminium sections Nos. 20671, 20672, 20690 & 20668 including 5mm thick plain sheet glass including rubber / neoprene beading and locking arrangement all as directed. Note : Aluminium frame for fixing three track windows shall be measured and paid separately.

S&F powder coated anodised aluminium frame for windows, ventilators with one or more rebates incl joining cleats for fixing etc complete all as specified

Supply only mild steel square guard bars 10 mm welded to steel windows / ventilators all as directed.

Supply and fix mild steel butt hinges medium weight cold rolled of size 100mm

Supply and fix mild steel tower bolt stove enamelled black with bright bolt 200mm long

Supply and fix mild steel pressed handles oval type stove enamelled black of size 150mm

Supply and fix 300 mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12 mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as directed.

Supply and fix aluminium anodised barrel tower bolt of extruded section 150mm long.

Supply and fix aluminium anodised handles of extruded section 150mm long.

Supply and fix aluminium die cast body door closure , hydraulically regulated of designation 2 , universal type for door shutters weighing between 36 to 60 Kg all as directed.in repairs

Supply and fix mild steel 300mm long ordinary rat tail rod pattern springs including roller and roller plate all as directed.

Supply and fix 20mm dia powder coated chromium plated curtain rods incl brackets etc all as directed.

Supply and fixing galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed

All as per item No. 52 above but fixed in repairs for wooden door/window.

Hacking out old broken glass (any thicknesss, size,quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads

and M&L for, frosted glass 5mm thick glazing with oil putty in squares exc 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing 3.00 mm thick ordinary quality plain sheet glass with oil putty in squares n exc 0.50 Sq m in each pane complete all as specified and as directed.

M&L for frosted glass 3mm thick glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and as directed.

Material and labour for two coats of synthetic enamel paint over a coat of pink primer for new wooden surfaces of any description exc 10 cm width or girth including preparation of surfaces all as directed.

M&L for preparation of old/new steel/steel ornamental and iron surfaces of any description exceeding 10cm in width or girth and applying two coats of synthetic enameled paint over a coat of red oxide primer complete all as specified.

M&L for preparation of old wood and wooden based surfaces of any description exceeding 10cm in width or girth and applying one coat of synthetic enameled paint

M&L for complete removal of existing treatment of walls or other plastered surfaces and preparing the surfaces and applying two coats of OBD (washable) over a layer of wall putty at any height complete all as specified &directed by Engineer-in-charge.

M&L for preparing old plastered surfaces and applying one coat of OBD (washable) at any height complete all as specified &directed by Engineer-in-charge.

M&L for preparing old plastered complete and applying two coat of Cement Base Paint at any height complete all as specified &directed by Engineer-in-charge.

M&L for preparing old plastered complete and applying one coat of Cement Base Paint at any height complete all as specified &directed by Engineer-in-charge.

Cutting chases in brick work, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10cm but n exc 20 cm girth

Taking up or down steel tubing for 15mm dia bore etc all as specified and directed

All as per item No 66 above but, 20 mm dia bore etc.

Supply and fixing 15 mm bore 3 Layer PP-R Polypropylene random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fitting fixed complete to walls, ceilings or in floors.

All as per item above No 68 but, 20 mm dia bore etc.

Supply and fix in repairs bib tap, 15 mm dia, CP cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferrule all as directed.

Supply and fix in repairs PVC bib tap 15 mm dia, screwed for iron pipe complete all as specified and directed. Make Prayag

Supply and fixing in repairs stop valve cast copper alloy, fancy type screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fix of size 15 mm bore

Supply and fix in repairs 15 mm dia pillar tap, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe all as directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 600 mm all as directed.

Supply and fix repairs PVC valveless, syphonic action type, flushing cistern,low level, all accesories all as directed.

Supply and fix in repairs vitreous China white squatting pan, Orissa pattern of size 580 X 440 mm width with integral foot rest set in cement concrete including flush pipe and connecting to trap / flushing cistren complete all as specified and directed.

Supply and fixed in repairs 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as directed.

All as per item No 77 but 75 mm dia

Supply and fix in repairs 110 mm bore PVC (SWR) bend, any radius all as directed.

All as per item No 79 above but 75 mm bore.

Supply and fix in repairs 110 mm bore PVC (SWR) branch piece single (single Y) equal or unequal all as directed.

All as per item No 81 above but 75 mm bore.

Supply and fix in repairs 110 mm bore PVC (SWR) branch piece double (double Y) equal or unequal all as directed.

All as per item No 83 above but 75 mm bore.

Supply and fix repairs PVC (SWR) floor trap, 75 mm dia with grating including jointing with slovent cement etc all as directed.

Supply and fixed in repairs 32 mm dia PVC flush pipe for low level flushing cistern and conecting to pedestal pan including jointing complete all as directed.

Supply and fix in repairs rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as directed.

All as per item No 87 above but water storage tank of capacity 1000 litres

All as per item No 87 above but water storage tank of capacity 2000 litres

Supply and fix in repairs wash hand basin vitreous China white , flat back or angle type of size 500 X 400 mm, waste chain and plug and porcelain stopper , waste pipe, a pair of brackets,or errecting stand all as specified and directed.

Supply and fixe in repairs stainless steel kitchen sink matt finish with draining over all size 950 X 510 mm and bowl size 410 X 410 X 230 mm, made out of 1.00 mm thick SS sheet of high quality including a pait of brackets, waste coupling, plug and chain, 32 mm dia PVC flexible waste pipe and nahani trap complete all as specified and directed.

S&F stainless steel kitchen plate rack made out of 0.63 mm thick stainless steel sheet of size 36''x 36''x 10'' with complete accessories including screws etc complete all as specified and directed by Engineer-in-Charge .

M & L for providing water proofing treatment on roofs, as per manufacturere's instructions and as specified after taking down/out as existing out at site etc complete all as specified and directed by Engineer-in-Charge. (a) Cleaning the newly plasterd surfaces with wire brushes and applying a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surface. (b) Applying and laying torch APP polymer modifiedbituminous membrance 3mm thick with non woven polyster matt as reinforced weighing not less than 3 kg/sqmts by therofusion process as per manufacturers specification including applying one coat of aluminium paint

Material and labour for plastering 10 mm in cement and sand mortar (1:3) using 100 % course sand on roof mied with and including WPC @ 3% by weight of cement and finished the surface even and smooth without using extra cement.

Supply and fix in repairs looking mirror of size 600 mm X450 mm all as directed.

Supply and fix in repairs looking mirror of size 600 mm X 1200 mm all as directed.

Supply and fix in repairs, shower rose with shower arm

Supply and fix in repairs plastic water closet seat cover, colored closed patern with flat bottom. cover and mild steel cromium plated or alumlised hinging device etc all as specified.

Supply and fix tubular towel rail, brass chromium plated 20 mm dia `D' type, 60 cm long between flanges including a pair of brackets all as directed.

Supply and fix in repairs framed work such as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other coverings, doors etc to be prepared for handing or sliding with and including either hooks and hinges or steel hanging door fittings ( exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete.

S&F of rolled steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410 (Gde-E- 250) quality-A

Dismantling and Deassemble existing rolling shutter of any description, replacment of any unserviceable part of rolling shutter due to which rolling shutter not properly closes and opens, properly overhaulling and again assemble including fixing in position of same opening

Supply and fix in repairs hooks (stay), heavy for large gates, hook and pintle hinges, large hasps and staples, chains; hand made sliding bolts, clamps, hold fasts, wall ties, plain angle cleats and similar small articles all as directed.

Material and labour for rendering 10 mm thick in cement mortar 1:4 on stone masonry surface finished even and smooth without using extra cement complete all as specified and as directed

M&L rendering 15mm thick in CM 1:6 on brick or concrete surface and finishing even and smooth without using extra cement

Material and labour in repairs for false ceiling with Vinyle faced Arm-Gyp-FB, ceiling 600 x 600 x 9mm thick with washable metallized polyster foil backing with Vinyle covered edges, supporting sections shall be of suitable size from same makes embossed on sections and level adjuster duly suspended by 2 mm dia GI wire fixed to roof at 600mm centre to centre as per manufacturere's instructions / specification and all as directed.

-ditto- item No 106 (here-in-before) but expect supporting sections snap grid

Dismantling of PGI /translucent sheets of any guage or any thickness

M&L for pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, coloure and design as approved by GE

M&L for pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, coloure and design as approved by GE

Material and labour for special treatment to sunken slab floor incl WC trap etc including cleaning and preparing the surface area for carrying out membrane water proofing treatment, then injection grouting the weak areas on the concrete surface with cementitious grout and applying 10mm thick cement plaster in CM 1:4. Then providing and laying Mineral Top APP (Atactic Polypropylene Polymer) modified prefabricated 5 layer 4mm thick water proofing membrane, black finished rainforce with non woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Litre per Sqm by the same membrane manufacturer of density at 25ºC, 0.87-0.89 Kg per litre and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torach and sealing all joints etc and preparing the surface complete. and providing PCC 1:5:10 type E2 using 40mm graded mechanically crushed stone aggregates in sunken slab and 75mm thick PCC 1:4:8 type D2 using 40mm graded mechanically crushed stone aggregates as base, 40mm bore GI pipe, light grade of length not less that 50 cm as spout, non-skid glazed tiles as per existing pattern/size/tint with and incl WC viterous china squatting pan 580x440mm with integral footrests/pedastal pan incl seat cover, white, area of WC exc 1.50 Sqm but nexc 5.00 sqm etc after dismantling the existing sunken floor etc complete all as specified and as directed Note : Work has to be carried out strictly by the authonticated applicator of the manufacturer and as per manufacturers specification as approved by GE.

Supply and fixing in repairs vitreous china wash down water closet (Pedestal pattern) white including fixing bolts with and including plastic water closet seat cover closed pattern with flat bottom and cover and MSCP almn hinges device complete connecting to 'P' or 'S' trap all as directed.

M&L stone sett flooring with stone seets of size 200 to 250mm long 150 to 200mm wide and 150mm deep and sides dresses bedded in cement and sand mortar (1:3 )joints 20mm thick grouted in cement and sand mortar (1:2) with admixture of matalic floor 5% by weight of cement struck flush etc complete all as specfied and directed by Enigneer-in-Charge

M&L edge stones to flooring with stone setts of size 250 to 300mm long 150 to 200mm wide and 450mm deep etc complete all as specified and directed by Engineer-in-Charge.

S&F for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or FE 310-0

Dismantling fencing wire mesh, any type

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire

Supply only Chain link MS galvaised fencing, any size or type

Labour for dismantling of aluminium door/windows/ventilator shuter from frame and replacement necessary accessories like floor spring, gasket rubber beading, glass of any description,etc. and again reassembled and fixed in the same opening complete all as specifed and directed

An amount of Rs 52,806.00 shall be deducted from BOQ on account of schedule of credit

Neha Enterprises

M/S-B.R.SONAWANE