NIT No: 24/SC-P2/EEC1/CE/ NRANVP/2026-27, Nava Raipur Atal Nagar, Dist. Raipur, Dated: 25.06.2026

Surface dressing of the ground including removing vegetation and making up undulations and in-equalities not exceeding 15 cms in depth/ height including disposal of rubbish upto all lead and lift.

Excavation for all types and sizes of foundations trenches and drains or for any other purpose including disposal of excavated stuff upto all lead and lift including dressing and leveling of pits. In all types of soil

Extra rate for quantity of work executed in or under water and/ or liquid mud including pumping out water.

Providing and filling in plinth with sand/ Crusher dust and hard moorum under floor in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering including dressing etc.complete.

Filling from available excavated stuff (Excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering with all lead and lift

Providing filling and compacting local earth (from approved source pit) in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering, including dressing etc. complete.

Supplying chlorpyriphos/ Lindane emulsifiable concentrate of 20% in sealed containers including delivery as specified.

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Surface treatment by spreading emulsion under floor, over the plinth area before laying base concrete @ 5 litres / sqm

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Treatment of inside of plinth masonry wall on using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall below plinth protection at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Diluting chemical emulsion (chlorpyrifos/ lindane) in water as per manufacturers recommendation and injecting for pre-constructional curative cum preventive anti-termite treatment:(Five year service guarantee bond to be signed by contractor) Treatment of outer side of plinth masonry wall using diluted chemical emulsion @ 1.5 litre per hole, including drilling 12 mm diameter holes in plinth wall at the junction of floor at the interval of 300 mm and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand).

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of from work. 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size).

Providing and laying nominal mix cement concrete with crushed stone aggregate using concrete mixer in foundation, plinth and at ground level excluding cost of from work. .1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size).

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-20

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-25Grade

Providing and laying design mix reinforced cement concrete with crushed graded stone aggregate 20mm nominal size using batching plant, transit mixer and concrete pump, in all works upto plinth level excluding cost of form work. M-30Grade

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All works above plinth level upto floor V level Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 1.10 times of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. Concrete of M35 grade with minimum cement content of 370 kg /cum

Extra for precast PCC/ RCC work of any mix including form work, hoisting and fixing in Cement Mortar. 1:2 (1 Cement : 2 coarse sand) and finishing with cement plaster in Cement Mortar 1:3 (1 Cement : 3 coarse sand) but excluding reinforcement.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: for first floor

Extra for laying PCC/RCC of any grade in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth: upto 3.6 m lvl

Providing and laying damp proof course (upto 50mm thick) with plain cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded crushed stone aggregate 20mm nominal size) including form work.

Water proofing material: Providing and mixing water proofing material in PCC/ RCC work in the proportion recommended by the manufacturer.

Applying a coat of hot bitumen VG-10 using @ 1.7kg/ sqm on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Foundations, footings, bases of columns plinth beam, curtain wall in any shape and size and all type of wall below plinth level.

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Wall of any thickness including attached pilasters, buttresses etc. in super structure.l.

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Columns, Pillars, Piers and likes- rectangular or square in shape

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Beams, lintels, cantilevers & walls

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Suspended floors, roofs, access platform, balconies (plain surfaces) and shelves (cast in situ)

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Edge of slab, breaks in floor and walls upto 200mm.

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Spiral / folded plate type stair cases including risers and landings

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Stair cases of all types excluding spiral and folded plate type, including risers and landings

Providing and fixing form work including centring, shuttering, strutting, staging, propping bracing etc. complete and including its removal at all levels, for: Weather shade, chhajja, Cornices and mouldings

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: Cement Mortar 1:4 (1 cement : 4 coarse sand)

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: Cement Mortar 1:5 (1 cement : 5 coarse sand)

Brick work with modular fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in foundation and plinth in: Cement Mortar 1:6 (1 cement : 6 coarse sand)

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Extra for brick work in superstructure above plinth level for every floor or part thereof in addition to rate for foundation and plinth:

Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level: Cement Mortar 1:3 (1 cement : 3 coarse sand)

Half brick thick brick masonry with fly-ash lime bricks (FaLG Bricks) confirming to IS:12894-2002 of class designation 4.0 in superstructure above plinth level upto plinth level: Cement Mortar 1:4 (1 cement : 4 coarse sand)

Extra for half brick work in superstructure above plinth level for every story or part thereof in addition to rate for upto plinth level:

Extra for providing and placing in position happing 25x1.60 mm or 2 Nose 6mm dia MS bars reinforcement at every third course of half brick masonry.

Providing wood work in frames of doors windows, clerestory windows and other frames wrought framed and fixed in position. Sal, bijasal, benteak, chair, haldu

Providing and fixing flush door shutters, conforming to IS 2202 (Part 1), interior grade, commercial type, core of block board construction with frame of first class hard wood and well matched commercial ply veneering with vertical grains, cross 35 mm thick (single leaf)

Providing and fixing factory made UPVC white colour casement/casement cum fixed glazed door comprising of UPVC multichambered frame, sash and mullion (where ever required ) extruded profiles duly reinforced with 1.60 + 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to UPVC profile, UPVC extruded glazing beads of appropriate dimension, EPDM gasket, zine alloy (white powder coaed) 3D hinges and one handle on each side of panels along with zine plated mild steel multi poin locking having transmission gear, cylinder with keeps and one side key, G.I. fasteners 100x8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & dirction of Engineer -in-Charge (Single/double glass panes and silicon sealent shall be paid separately vide chapter no. 9.51.958.959 Respectiley). Note: For UPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Casement door with 3D hinges made of (big series) frame 67 x 110 mm both having wall thickness of 2.3 + 0.2 mm and single glazing bead/double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm)

providing and fixing clear float toughened glass door or partition in required thickness frameless in appropriated sizes inclusive of edge molding polish and making required size slot or hole for patch fitting/hardware etc. The glass to be assembled together with patch fitting and hardware in proper alignmnent with all labour tools and tackles etc complete. (Patch fittings and hard ware to be paid for separately). 10 mm thick for door/partition

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately: For fixed portion

Providing and fixing aluminium work for doors, windows, ventilators and partitions made out of extruded aluminium standard sections (main section with minimum 1.5mm thickness) conforming to IS: 733, IS: 1285 mitred and jointed mechanically including aluminium cleats, neoprene weather stripping gasket beveled edge beading, screws duly fixed in wall/ floor with fixing clips or hold fasteners or bolts and nuts as required aluminium sections shall be anodized transparent or dyed to approved shade according to IS: 1868, minimum anodic coating shall be of grade AC-15. (Glazing to be paid for separately: For shutter of doors, windows & ventilators including providing and making provision for fixing of fitting wherever required including the cost of PVC/ neoprene gasket required (Fittings shall be paid for separately).

Providing and fixing float glass panes with steel glazing clips and special metal sash putty of approved make in steel doors, windows, ventilators: 5mm thick

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete. (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 6 mm thickness

Providing and fixing M.S. grill of approved pattern made of M.S. flats or square or round bars welded to steel frame of windows etc. including applying a priming coat welded to frame with all necessary fitting complete including applying a priming of red oxide zinc chromate primer.

Providing stainless steel railing/ grill made of S.S. flats, hollow S.S. pipe or square/ rectangular sections of approved design fixing in stair case, balcony or other places with metal fasteners and stainless steel bolts etc complete. SS Grade 304

Providing and fixing in position doors, windows and ventilators frames made of cold rolled pressed steel sheet framed profiles made from commercial M.S. Sheets conforming to I.S. 513 of 1973 and as per general specifications of I.S 4351 including hinges jamb, lock jamb, steel butt hinges, base tie, joints mitred and welded with 10cm long legs of size 15x3mm M.S. flat, embedded in cement concrete blocks 15x10x10cm size of grade M-10 or rawl plugs and screws or with fixing clips or with bolts and nuts including neatly compacted filling M-10 cement concrete in profile section applying a priming coat of red oxide zinc chromate primer. Single rebate/ mullion 80mmx50mm size, 1.6mm thick sheet

Providing and fixing in position doors, windows and ventilators frames made of cold rolled pressed steel sheet framed profiles made from commercial M.S. Sheets conforming to I.S. 513 of 1973 and as per general specifications of I.S 4351 including hinges jamb, lock jamb, steel butt hinges, base tie, joints mitred and welded with 10cm long legs of size 15x3mm M.S. flat, embedded in cement concrete blocks 15x10x10cm size of grade M-10 or rawl plugs and screws or with fixing clips or with bolts and nuts including neatly compacted filling M-10 cement concrete in profile section applying a priming coat of red oxide zinc chromate primer. Single rebate 100mm x 50mm size, 1.6mm thick sheet.

Providing and fixing antique/ SS finished brass door latch with antique/ SS polished MS screw complete: 300 x16x5 mm

Providing and fixing antique/ SS finished brass butt hinges with antique/SS polished MS screw complete: 125x85x5.50 mm (Heavy Type)

Providing and fixing antique/ SS finished brass parliamentary hinges with antique/ SS polished MS screw complete: 150x125x27x5mm

Providing and fixing antique/ SS finished brass sliding door bolt with necessary bolts, nuts and antique/ SS polished MS screw complete: 300x16mm

Providing and fixing stainless steel hanging door stopper with necessary stainless steel screws complete. Single

Providing and fixing antique/ SS finished brass hanging door stopper with necessary antique/ SS finished MS steel screws complete.

Providing and fixing antique/ SS finished brass tower bolts (Barrel type) with antique/ SS polished MS screw complete: 250 x10 mm

Providing and fixing antique/ SS finished brass handles with antique/ SS polished MS screw complete: 125 mm

Providing and fixing stainless steel cutt hinges having thickness 1.2mm necessary stainless steel screws etc complete. 75x19x13mm

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc complete.

Providing and fixing stainless steel butt hinges with necessary stainless steel screws etc complete. 125x2.5mm (heavy)

Providing and fixing stainless steel sliding door bolts with 16mm rod, 2.5mm thick flap, necessary stainless steel nuts bolts and screws etc complete.. 300mm

Providing and Fixing SS finished brass tower bolts (Barrel type) with necessary SS finished MS screws complete. 250x10mm

Providing and fixing stainless steel door handles having flap thickness 2.5mm, necessary stainless steel screws etc complete. 125 mm

Providing and fixing SS finished brass indication bolts (vacant/engaged) with necessary SS finished MS screws complete.

Providing and fixing brass door latch with brass polished MS screws complete: 250x16x5 mm

Providing and fixing bright finished brass rim latch and lock 100mm and pair of knob with brass polished MS screws etc. Complete

Providing and fixing aluminium sliding door bolts with 16mm rod, necessary nickel plated iron nuts bolts and screws etc complete. 250x16mm

Providing and fixing aluminium tower bolts (Barrel type) with necessary nickel plated iron screws etc complete. 150 x10mm

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Cement concrete flooring with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm) finished with a floating coat of neat cement. 50 mm thick

Providing and fixing factory made UPVC door frame made of UPVC profile section having an overall dimension as below (tolerance ± 1mm) with wall thickness 2.0mm ± 0.2mm, corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 X 19mm and 1mm ± 0.1mm wall thickness and 3nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge Extruded section Profile size 48x40 mm.

Providing and fixing 30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on either side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per Manufacturer’s specification including 3 nos ISI marked stainless steel hinges of size 100x58x1.9 mm complete. (for W.C. and bathroom door shutter). Both side Pre-laminated panel PVC door shutter

Providing and fixing M.S. fan clamp/ hook for ceiling fan made out of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs, beams during laying including painting the exposed portion of loop.

Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete. 2- Top/side patch glass or L-connector patch SS grade 304

Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete. 3- Bottom patch to be connected with floor machine

Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete. 4- Bottom lock patch with three key SS grade 304

Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete. 6- Two way action Hydraulic floor spring machine heavy duty double cylinder type capacity 120/150 kg mounted on floor including reuired cutting on floor and proper grouting with rich cement mortar.

Providing and fixing of stainless steel grade 316 patch fitting and hardware of approved (Hardwyn, Ozone, Godrej) make in frame less toughened glass door or partition in proper alignment with all tools tackles and labour etc complete. 7- H type handle 32 x 600 mm SS 304 grade

6mm thick cement plaster of mix: In Cement mortar 1:3(1 cement : 3 fine sand)

6mm thick cement plaster of mix: In Cement mortar 1:4 (1 cement : 4 fine sand)

Providing and making 12mm thick cement plaster of mix: In Cement Mortar 1:4 (1 cement : 4 fine sand)

Providing and making 12mm thick cement plaster of mix: In Cement Mortar 1:5 (1 cement : 5 fine sand)

15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement Mortar 1:4 (1 cement : 4 fine sand)

15mm thick cement plaster on the rough side of single or half brick wall of mix: In Cement mortar 1:5 (1 cement :5 fine sand)

Neat Cement punning.

Providing and making 18 mm thick cement plaster with under layer of 12mm thick cement plaster 1:5 (1 cement : 5 fine sand) finished with a top layer of 6mm thick cement plaster 1:3 (1 cement : 3 fine sand).

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing and applying Acrylic washable Distemper or lite economy Plastic emulsion paint having VOC content less than 50gms/ lit Minimum two coats up to final finish applied @ 1.25 Kg/ 10Sqm as per relevant I.S. Code 428:2000 (product such as Tractor Uno, Dulux Duval, Berger Bison, Opus Style/lite economy emulsion product such as Asian Tactor Spark , Dulux Pomise sheen, Neroloc Litil Master, Berger Bison Lite, Nippon Superio.) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour complete for the work.

15 mm thick Table rubbed polished Granite stone slab in risers and treads of steps skirting dado and pillars laid on 12mm (Average) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry including rubbing and polishing etc. complete (single stone is to be used for risers and treads of steps and width of stone for skirting and dado shall be equal to the height of skirting & dado and length of 1.0 m). Granite stone black

KOTA stone slab 25mm thick in risers and treads of steps, skirting dado and pillar laid in 12mm (Average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete. (single stone is to be used for riser and treads of steps and the width of stone for skirting and dado shall be equal to the height of skirting/ dado up to length of 1.0 M.)

Extra for nosing in steps and treads of kota stone slab.

Extra for providing edge moulding to 15mm thick stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

15 mm thick Table rubbed polished Granite stone slab flooring laid over 20mm (Average) thick base of cement mortar 1:4 (1 cement : 4 coarsesand) laid and jointed with grey cement slurry including rubbing and polishing etc. complete. (Area of slab should be 0.50 sqm and above) Granite stone black

Providing and laying DOUBLE/MULTI CHARGE (minimum 2.0 mm thick layer) VITRIFIED floor tiles with water absorption less than 0.05% and conforming to IS:15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm) laid on 20mm thick cement mortar 1:4 (1cement: 4 coarse sand) including grouting the joints with withe cement and matching pigments etc. complete. Size 600x600mm thickness 9 to 10mm

Providing and laying Glazed Vitrified wall/dado tiles (GVT/PGVT) with digital print of random design with water absorption less than 0.08% and conforming to IS: 15622-2017 of Ist quality of approved make in all colours and shades and size mentioned below (+/-10mm) for wall /dado laid on 12mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size 600x600mm thickness 9 to 10 mm

Providing and Laying Matt/Glazed finish HOMOGENEOUS ACROSS FULL BODY VITRIFIED floor tiles (heavy duty) with water absorption less than 0.05% and conforming to IS: 15622-2017 of 1st quality of approved make in all colours and shades and size mentioned below (+/- 10mm), laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete. Size 600x600mm thickness 9 to 10mm

Providing and laying vitrified floor tiles with soluble salt printing, of size 600x600mm with water absorption less than 0.5% and conforming to IS : 15622 of approved make, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete

Providing and laying ceramic glazed floor tiles conforming to IS : 15622 of approved size, make, colour, shade laid on 20 mm thick Cement Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement mixed with matching pigment etc., complete. Size 300x300mm

Providing and fixing ceramic glazed wall tiles conforming to IS : 15622 of approved make, colours, shades and size on wall and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with matching pigment complete. Size above 200x300mm

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing and constructing soak pit 1.20x1.20x1.20m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design.

Providing, lowering, laying, aligning, fixing in position at and jointing at all level/ depths ISI marked HDPE pipes of PE-100 grade and PN 6 for sewer application as per IS 14333-1996 (amended upto date) in trenches in complete including all material, labour, testing and commissioning as per direction of Engineer. Note : E/w to be measured and paid separately. 150 mm dia

Providing and applying Polymaric cement primer on all surface applied @ 0.80 litrs/10 sqm as per relevant I.S. code 15489:1974 (product such as Birla white primacoat/activcoat, Asian Trucare , Dulux interior cement primer, Opus Calista / I10 ) with all tool tackles and labour etc. complete for the work .

Providing and applying 2mm thick white cement based polymeric Exterior grade Putty with minimum 3 coats applied @ 5.4 kg/ 10Sqm as per relevant IS code 17545:2021 (Product such as Birla wall care, Asian trucare, JK wall putty, Berger Bison wall putty) to make the surface smooth and even with all tools tackles and labour etc. complete for the work.

Providing and applying on exterior surface with PREMIUM Exterior emulsion paint of required shade to give protective and water proof finish minimum 3 coats applied @ 1.40 lit / 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D , C (Glossy /Semi Glossy finish ) (Product such as Asian Apex , Dulux Weather Shield Prima E900 , Berger Weathercoat Antidust , Nerolac Everlas Excel , Nippon Sumo Etra, Opus True flex) inclusive of providing abro tape on edges and articleand cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.(With 3Year Warranty.)

Providing and applying priming coat on wood work applied @ 0.50 lit/Sqm as per relevant IS code 3536:1999 ( product such Asian trucare, Burger Wood Keeper, Dulux Duwel wood primer) with all tool tackles and labour etc for complete the work.

Plinth protection: Making 50mm thick plinth protection of plain cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with sand including finishing the top smooth.

Providing and applying Premium plastic emulsion paint with roller application minimum three coats applied @ 0.75 lit / 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -1 Class D & C ( Glossy and Semi Glossy Finish) of required shade (Product such as Asian Apcolite Premium , Dulux Super Cover, Berger Easy Clean , Nippon Breezee Metex Gold, Opus I-50 / Calista) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work.(with 3 year Warranty)

Providing and applying Luxury plastic emulsion paint with roller application minimum three coats applied @ 1.25 lit / 10Sqm up to final finish as per relevant Type -1 Class D , C , B & A (Glossy /Semi Glossy and Matt , Egg Shell or Satin finish ) of required shade (Product such as Asian Royale Shyne, Dulux Velvet Touch, Berger Silk Luxury Emulsion , Nippon Impression Pearl , Opus Pure Elegance) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc, complete for the work. (with 4 Years Warranty )

Providing and applying on exterior surface with ECONOMY Exterior Emulsion paint of required shades to give protective and water proof finish minimum three coats applied @ 1.43 lit / 10Sqm up to final finish as per relevant I.S. Code 15489:2013 Type -2 Class D , C ( Glossy /Semi Glossy finish ) (Product such as Asian Ace , Dulux Promise Exterior , Berger Wall Masta , Nerolac Suraksha Plus , Nippon Shogun Opus, One Style Power Bright) inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc. complete for the work (With 2 Year Warranty)

Providing and applying acrylic modified resin EXTERIOR TEXTURED with special quality silica quartz plaster as an intermediate coating on external surface giving protective layer and decorative finish on plastered surface in approved design and shade (product such as Asian Apex Series Duracast Dulux weathersheald sandtax creation) as per manufacturer's specifications inclusive of providing abro tape on edges and article and cleaning of door, windows, floor and surface as required with all tools tackles and labour etc.complete for the work. 2.0mm thickness (average) having design scratched with leveled & smooth surface.

Providing and fixing chicken mesh weighting not less than 250 gms/ sqm as per IS: specification in the required width with 10 mm long steel nails on vertical and horizontal surface near R.C.C. and brick walls junctions including scaffolding and all lead and lifts etc. complete before plastering upto 10mts in height.

Designing, providing and fixing aluminium frame work made of special aluminium section on building face with M.S. angle iron brackets fixed on RCC structure with S.S. hold fasteners, including providing and fixing two sided structural adhesive tape of appropriate grade (NORTON or equivalent), on aluminium sections for fixing aluminium/ glass panel,sealing on periphery of frame work, by providing EPDM gasket, silicon weather sealant between aluminium frame and building structure including hire charges of double scaffolding complete.

Providing and fixing aluminium composite panels in approved panel sizes, thickness and shape on aluminium frame work on face of building. (Frame to be paid separately) 4mm thick

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for underground structures using rough Kota stone and consisting of: i) 1st layer of 22mm to 25mm thick approved rough Kota stone slab over a 25mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. ii) 2nd layer of 25mm thick cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound. iii) Finishing top with stone aggregate of 10mm to 12mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Providing and laying integral cement based treatment for water proofing on the vertical surface at all levels by fixing 22 mm to 25mm thick rough Kota stone slab with cement slurry mixed with water proofing compound conforming to IS:2645 with a gap of 20mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with 20mm thick cement mortar 1:3 (1 cement : 3 coarse sand) with neat cement punning mixed with water proofing compound complete

Providing and laying water proofing treatment in sunken portion of WCs, bathroom, kitchen etc., by applying cement slurry mixed with water proofing cement compound consisting of following applications including surface preparation: i) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. ii) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound@ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Supply and fixing of polymer precoated galvalume profile sheets (PPGL) of approved size, shape and pitch of corrugation, total coated thickness (TCT) 0.60 mm +/- 5%, epoxy primer on both side of the sheet and colour polyester top coat 18-20 microns and 6-7 microns on bottom. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes

Providing and fixing false ceiling at all heights with 15mm thick integral densified tegular edged light weight calcium silicate false ceiling tile reinforced with fibre and natural filler false ceiling tiles of size 595x595xmm of approved testure, design and paterns (such as cosmos, spinton, quatra, golb) having NRC (Noise Reducation coefficient) of 0.50 (minimum) as per IS : 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS: 476 (part-4), fire performance as per BS:476 (part 6 & 7), humidity resistance of 100%, thermal conductivity 0.048 to 0.050 W/m0KC as per ASTM 518:1991, Weight 1.900 Kg to 2.100 Kg per tile, 15 MM Edge Density Having 450 Kg/cum & 10 mm Central Portion of tile having 350 Kg/cum .3000mm to be fixed on periphery wall/ partition with the hep of plastic rawl plugs at 450mm center to center and 40mm long dry wall S.Sscrews. The work shall be carried out as per specifications, drawings and as per directions of the Enginer-In-Charge Ceiling height up 3.5mt from adjacent floor level extra height to be paid separately. n true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @120 grams per sqm including both sides) comprising of main T runners of size 24x38 mm of length 3000mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermedicate cross -T of size 24x32 mm of length 600mm to form grid module of size 600x600mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 40mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000 mm length & L-shape level adjuster of size 85x25x25x2mm Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length

Providing and fixing at all height false ceiling consisting of frame work "W" / "U" / "L" sections made of G.I. sheet with zinc coating of grade 120 consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.55mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and alsoincluding the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed including providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS: 2095- Part-I all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 32 mm nominal outer dia .Pipes. (DWS)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (UV stabilized, Nitrile Insulation) 50 mm nominal outer dia .Pipes. (up water) (DWS)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. CONCEALED WORK including cutting chases and making good the walls etc., 15 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. CONCEALED WORK including cutting chases and making good the walls etc., 20 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. CONCEALED WORK including cutting chases and making good the walls etc., 25 mm nominal outer dia .Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. EXTERNAL WORK 32 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. EXTERNAL WORK 40 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This included jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. EXTERNAL WORK 100mm nominal inner dia pipes

Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore

Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end): 32 mm nominal bore.

Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end): 40 mm nominal bore

Providing and fixing brass/ gun metal gate valve with C.I. wheel of approved quality (screwed end): 50 mm nominal bore

Providing and fixing gun metal non- return valve (horizontal type) of approved quality (screwed end) : 50 mm nominal bore

Cutting holes upto 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including finishing complete so as to make it leak proof.

Cutting holes more than 20x20 cm and upto 30x30 cm in walls including making good the same :

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Bib cock (400 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Long nose bib cock (500gms)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Piller Cock (400 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Stop cock (concealed) (600 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Two way bib cock (800 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Angle valve for basin mixer and geyser points (450 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Kitchen sink mixer with cast swivel spout (1000 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Wall mixer with elegant knob (1400 grams)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Bottle trap set with extension pipes

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Toilet paper holder

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Soap dish plate

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Shower rose (revolving type) (150mm)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Towel rail (600mm long x 20mm dia)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Towel ring (150 mm dia)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Health foscet (hand jet) with flexible connection pipe (for WC)

Providing and fixing 15 mm nominal bore C.P. brass fittings of approved make and conforming to IS:8931 including C.P. brass extension if required: Hand shower set with flexible extension pipe

Providing and fixing stainless steel drain jali of approved make/quality.

Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified. 25 mm dia

Providing and fixing brass GM/ ball valve (full bore type) with plastic coated lever and screwed female ends tested to 20 Kg/ cm2 of approved quality as specified. 50 mm nominal bore

Providing and fixing water closet squatting pan (Indian type W.C. pan ), 100mm sand cast Iron P or S trap, 10 litre low level P.V.C. flushing cistern (same colour) conforming to IS : 7231, with flush bend and other fittings and fixtures complete including cutting and making good the walls and floors wherever required : Coloured Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : Coloured pedestal type

Providing and fixing vitreous china water closet (European type W.C. pan) with white ISI marked plastic seat and lid, 10 litre low level white P.V.C. flushing cistern (same colour), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : Coloured wall hung type

Providing and fixing white vitreous china urinal basin with waste fitting as per IS : 2556, and other couplings in C.P. brass complete: Flat back half stall urinal of size 460x380x250mm

Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : White Oval or round size 550x400mm

Providing and fixing vitreous china wash basin with C.I. brackets, 32 mm C.P. brass waste of standard pattern, including painting of brackets, cutting and making good the walls wherever required : Coloured Oval or round size 550x400mm.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink with drain board as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : 1145x510 mm bowl size 560x410x241 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink with drain board as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : 1040x510 mm bowl size 460x410x200 mm

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink without drain board as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required : 345x445 mm bowl depth 200 mm.

Providing and fixing 600x450 mm beveled edge 4mm mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600x120x5mm glass shelf with edges rounded off supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 5mm thick Mirror

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 75 mm dia pipe.

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 110 mm dia pipe.

Providing and fixing on wall face or under floor UV stabilized Unplasticised Rigid PVC pipes (single socketed) having 3.2mm wall thickness conforming to IS : 13592 (4kg/sqcm) including required couplers, jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc complete. 150 mm dia pipe.

Providing and fixing 15 mm nominal bore C.P copper connection pipe with C.P brass nuts collar and PVC bush of approved quality: 45 CM length

Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

Providing and fixing UV stabilized Unplasticised -PVC pipe clips of approved design to Rigid PVC pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing UV stabilized Unplasticised -PVC pipe clips of approved design to Rigid PVC pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Tee/ Tee with door/ Bend 45°/ Bend 90° 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Tee/ Tee with door/ Bend 45°/ Bend 90° 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Double "Y" with or without door 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Double "Y" with or without door 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Vent covel 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Vent covel 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Access door cap 75 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Access door cap 110 mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. P trap 110mmx110mm long

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Nahani trap 110x75mm

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Multi floor trap 110

Providing and fixing on wall face UV stabilized Unplasticised - PVC moulded fittings/ accessories having 3.2mm wall thickness for Rigid PVC pipes conforming to IS : 13592 (heavy) jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain reducing Tee 110x75mm

Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality: Bib cock (350 grams)

Providing and fixing 15 mm nominal bore Brass bib/stop cock of approved quality: Stop cock (350 grams)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Constructing masonry Chamber 30x30x50 cm, inside with fly ash bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design :

Providing and fixing filter of minimum 100 litre capacity for roof top rain water harvesting through tube well consisting of two layered HDPE tank with five layers (each layers of minimum 100 mm) consist of coarse sand, 4mm, 6mm, 8mm & 12 mm gravels with stainless steel wire mesh fixed between each layer with suitable length and sufficient numbers of 110 mm dia PVC pipe pieces in the bottom of tank to support the above layer including fixing of inlet and out let P.V.C. pipe of required diameter upto 2 metre length on each side, Cement Concrete plateform of required size complete as directed by Engineer in charge. (excluding cost of tubewell and inlet and outlet pipe beyond 2 metre)

Providing and fixing 80-100 mm dia PVC ball valve for inlet/ outlet of rain water harvesting pipe and filter.

Providing and fixing 15mm thick Granite (machine cut, table rubbed & mirror polished on both sides) for partition curtain in toilets or similar locations of required size in wall with cement mortar 1:4 (1 cement : 4 coarse sand) including cutting chase in wall and joint with wall treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. Granite stone black

Providing and fixing 15mm thick Granite (machine cut, table rubbed & mirror polished on both sides) for partition curtain in toilets or similar locations of required size in wall with cement mortar 1:4 (1 cement : 4 coarse sand) including cutting chase in wall and joint with wall treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. Granite stone black

15mm thick Granite work (machine cut, table rubbed & mirror polished) for kitchen platform, vanity counters, window sills and similar locations of required size laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) including joints treated with white cement mixed with matching pigment including rubbing and polishing to edge moulding to give high gloss finish. Granite stone black

Providing and fixing in position precast R.C.C. manhole cover and frame L D- 2.5 of required shape and approved quality Rectangular shape 600x450mm internal dimensions

Replacement of M.S. foot rests in manholes including dismantling concrete blocks and fixing with 20x20x10 cm cement concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) : With 20x20 mm square bar

Supplying and stacking of good earth at site including royalty, loading, unloading and carriage upto 5 km (earth measured in stacks will be reduced by 20% for payment)

Supplying and stacking sludge at site decayed cow dung manure from approved source, including loading unloading and carriage upto 5 km ( sludge measured in stacks will be reduced by 8% for payment).

Spreading of sludge, dump manure or/ and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately).

Providing and planting following herbs in garden including preparation of soil, base plantation providing and spreading different fertilizers, soil and sand: Hedges like Alife, Dorenta, Tikoma etc

Providing and planting following herbs in garden including preparation of soil, base plantation providing and spreading different fertilizers, soil and sand: Ferns Arica palm China palm etc (3year old )

Providing and planting following herbs in garden including preparation of soil, base plantation providing and spreading different fertilizers, soil and sand: Hibiscus (Flower)/ Rose

Providing and planting following herbs in garden including preparation of soil, base plantation providing and spreading different fertilizers, soil and sand: Carpet grass (well developed)

Grassing with ‘Doob’ grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from weeds and fit for mowing including supplying good earth if needed (the good earth shall be paid for separately). In rows 5 cm apart in either direction.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep.

Constructing masonry Chamber 60x60x75 cm, inside with modular well burnt clay bricks of 35 kg/ cm² in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Providing and fixing M.S. round holding down bolts with nuts, washer and plate in cement concrete complete.

Providing and applying plaster of paris putty over plastered wall surface including scaffolding complete Upto 2 mm thickness to make surface even and smooth in line and level.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete 150mm thick as per standard design: 150 mm diameter S.W. pipe

Providing and constructing brick masonry chamber for underground pipe and and bends with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets :

Providing and constructing brick work for extra depth beyond 45 cm of brick masonry chamber with well burnt modular clay bricks crushing strength not less than 35kg/cm2 in cement mortar 1:4 (1 cement : 4 coarse sand) with inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls: For 455x610 mm size

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to all lifts and lead including removal and disposal of top organic soil not exceeding 150 mm in thickness if required and as per relevant clauses of section-200. In area of light jungle

Excavation in Soil (by Mechanical Means.) Excavation for roadway in soil using mechanical means including loading in tipper for carrying of cut earth to embankment site and unloading with all lifts and lead.

Granular Sub-base with Close Graded Material (Table:- 400-1) Plant Mix Method with Mechanically crushed stone only(Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 ) Plant mix method (with Mechanically crushed stone only) for grading-III Material

Providing & Laying precast interlocking concrete block of minimum compressive strength of 300kg/sq.cm and approved size, shape/ pattern over coarse sand bed of thickness upto 40 mm and joints thick filled with fine sand including leveling with surface vibrator, temping and sweeping etc.complete as per IRC-SP-63-2004. 80 mm thick precast Interlocking concrete block of C.C. M 40 grade on On area of light traffic/residensial street 80mm thick Polymer coated coloured precast interlock concrete blocks

Wet Mix Macadam (Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.)as per clause 406.

Prime coat (Providing and applying primer coat with oil based bitumen emulsion (SS-1, grade confirming to IS:8887) on prepared surface of granular Base including clearing of road surface and spraying primer using mechanical means as per clause 502. on (i) WBM/WMM surface @0.85 Kg/sqm.

Prime coat (Providing and applying primer coat with oil based bitumen emulsion (SS-1, grade confirming to IS:8887) on prepared surface of granular Base including clearing of road surface and spraying primer using mechanical means as per clause 502. on (ii) Granular surfaces treated with primes @ 0.30 kg /Sqm

Tack coat (Providing and applying tack coat with bitumen emulsion RS-1, grade confirming to IS:8887 using emulsion pressure distributor on the prepared bituminous surface cleaned with mechanical broom) as per clause 503 & 112. on Bituminous surfaces @ 0.25 kg per sqm

Dense Graded Bituminous Macadam (Providing and laying dense graded bituminous macadam with 120 -200 TPH higher capacity Batch Type HMP using crushed aggregates of specified grading, premixed with bituminous binder VG-40 by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 & 112 complete in all respects) With sensor paver finisher for Grading I (37.5 mm nominal size, bitumen Mcontent minimum 4.0% )

Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement as per IRC:58 over a prepared sub-base, coarse and fine aggregate conforming to IS:383 and graded as per table 600-3 mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing as per clause 602.) With Cement concrete grade M-30 and minimum cement content @ 375 kg/cum.

Bituminous Concrete (Providing and laying bituminous concretewith120 -200 TPH higher capacity Batch Type Hot Mix Plant using crushed aggregates of specified grading, premixed with bituminous binder VG-40 and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 & 112 complete in all respects) With sensor paver finisher for Grading-I (19 mm nominal size) with bitumen minimum 5.5 %

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in PCC M20 grade on PCC M10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine,foundation concrete laid manually, all complete as per clause 409)

Road Marking with Hot Applied Thermoplastic Compound with Reflectorizing Glass Beads (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorizing glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-1997. The finished surface to be level, uniform and free from streaks and holes.)

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 90 cm equilateral triangle (2.0 mm thick)

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 80 cm x 60 cm rectangular (2.0 mm thick)

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 60 cm equilateral triangle (1.5mm thick)

"Retro-reflectorized Traffic signs as per Clause 801. Providing and fixing of retro-reflectorized cautionary, mandatory and informatory sign over retro-reflective sheeting of required grade confirming to ASTM D 4956 as per IRC:67-2022 made of retro-reflective type sheeting fixed over Aluminium Sheeting/Aluminium Composite Material (ACM) sheeting including application of fluorination coating applied on exposed surfaces of aluminium to ensure corrosion resistance, supported on a mild steel base frame of ISA 40 x 40 x 6 mm and mild steel angles for post 75 mm x 75 mm x 6mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm, as per approved drawing and painting all exposed components of the signs and supports with primer and 2 coats of epoxy paint or powder coating and the part of post below ground shall be painted with 3 coats of redoxide paint as per clause 7.2 of IRC:67-2022. (Note: The details of manufacturer, type of sheeting, month and year of installation, project details and other details along with QR code as detailed in clause 13.2 and Annexure-VII of IRC:67-2022 shall be printed on back side of the sign board.)" With Aluminium sheeting "Made of Class-A High Intensity Micro Prismatic Engineering Grade Sheeting of Type I confirming to Table 6.3 of IRC:67-202 "With Aluminium sheeting of 2 mm & 1.5 thickness" 60 cm Circular (1.5mm thick)

Painting on Concrete Surfaces Two coats on new surfaces (Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces)

Providing 1st class bedding below pipes with graded sand or other granular materials passing through 5.6 mm sieve as per clause 2904.

Providing and planting of 3‟0” to 4‟0” heighted wasingtonia, filipheria/bismarkia novelist plam plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). (Foxtail Palm, Phonix Palm)Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of 4‟0” to 5‟0” heighted Ficus prestige/Blackiana plants with 1‟6” x 1‟6” depth pit formation and soil preparation, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of Bogenbelia dwarf, chandni dwarf, kaner dwarf vr flower bearing plants with 0‟9” x 0‟9” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). ( Nicodia,Euphorbia milii). Up to 12 month maintenance after work completed and as direction of engineer in charge

Providing and planting of dwarf red Ekalyha plants showing mass effect view with 0‟9” x 0‟9”x1‟0” depth pit formation and soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed.

Providing and planting of Golden durenta multi branches plants for showing mass effect in 0‟6” x 0‟6” distance with soil preparation work‟s, (Mixing organic manure and plant‟s protection insecticide). Up to 12 month maintenance after work completed and as direction of engineer in charge

Planting of Trees and their maintenance for one year (Planting of trees by the row side(Avenue trees) in 0.60m dia.holes, 1m. Deep dug in the ground, mixing the soil with decayed farm yard/sludge manure,planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year

Earth work in excavation for pipe trench in ordinary soil are as including dressing, watering and ramming and disposal of excavated earth all lead and lift, disposal earth to be leveled, neatly dressed.

Earth work in Excavation for pipe trench in Hard Soil areas including dressing, watering and ramming and disposal of Excavated earth all lead and lift, disposal earth to be leveled, neatly dressed.

Filling available excavated earth in trenches, plinth sides of foundation in layers not exceeding 20cm. in depth including consolidation of each layer by ramming watering, all lead and lift in all kinds of soils

Providing, laying and jointing followings ISI marked O-PVC (Oriented uplasticized polyvinyl chloride) ring fit type pipe having orientation class 500 (IS 16647) with integral homogeneous spigot having elastomeric seeling ring made of EPDM rubber (one per pipe) including testing of joint, cost of jointing materials etc. complete in all respect. Presure Rating as 110mm diameter

Providing, laying and jointing followings ISI marked O-PVC (Oriented uplasticized polyvinyl chloride) ring fit type pipe having orientation class 500 (IS 16647) with integral homogeneous spigot having elastomeric seeling ring made of EPDM rubber (one per pipe) including testing of joint, cost of jointing materials etc. complete in all respect. Presure Rating as 160mm diameter

Providing, laying and jointing socket & spigot centrifugally cast (Spun) Ductile Iron pressure pipes with inside cement mortar lining (classK-7) Conforming to IS 8329/2000 with suitable Rubber Gasket (Pushon) joints as per IS:5382/85 including testing of joint (laying Conforming to IS 12288 : 1987) 100mm diameter

Providing, laying and jointing socket & spigot centrifugally cast (Spun) Ductile Iron pressure pipes with inside cement mortar lining (classK-7) Conforming to IS 8329/2000 with suitable Rubber Gasket (Pushon) joints as per IS:5382/85 including testing of joint (laying Conforming to IS 12288 : 1987) 150mm diameter

Providing & Supplying D.I. Specials & Fittings For all types of specials, bends, tees.. etc. 80 to 300 mm dia

Supply & Filling moorum/river sand for pipe bedding or over the pipe (including supply)

Providing & fixing of following Ductile iron double flanged sluice valves as per I.S.:14846-2000 fitted with cap including jointing & testing with cost of jointing material such as bolts, nuts, rubber insertions etc. all complete. 80 mm dia. PN-1.6

Providing & fixing of following Ductile iron double flanged sluice valves as per I.S.:14846-2000 fitted with cap including jointing & testing with cost of jointing material such as bolts, nuts, rubber insertions etc. all complete. 100 mm dia. PN-1.6

Providing & fixing of following Ductile iron double flanged sluice valves as per I.S.:14846-2000 fitted with cap including jointing & testing with cost of jointing material such as bolts, nuts, rubber insertions etc. all complete. 150 mm dia. PN-1.6

Providing & fixing following ductile iron single chamber triple function temper proof air valves, small orifice with screwed end as per IS : 14845-2000 including jointing & testing with cost of jointing material and rubber insertion all complete as per IS :13095-1991 80 mm dia PN-1.6

Providing, fixing and testing following double flanged cast iron(horizontal cast) pipe per IS :7181of One Meter length. 80mm diameter

Providing, laying, jointing, testing and commissioning of D.I Dismantling joint with M.S. Nut stud & washers coated for rust prevention & internal rubber rings etc. complete assembly set as per type design inclusive of all taxes & duties, insurance, loading/ unloading & stacking FOR at site all complete as per technical Specifications and as per direction of Engineer. 80mm diameter

Providing, laying, jointing, testing and commissioning of D.I Dismantling joint with M.S. Nut stud & washers coated for rust prevention & internal rubber rings etc. complete assembly set as per type design inclusive of all taxes & duties, insurance, loading/ unloading & stacking FOR at site all complete as per technical Specifications and as per direction of Engineer. 100mm diameter

Providing, laying, jointing, testing and commissioning of D.I Dismantling joint with M.S. Nut stud & washers coated for rust prevention & internal rubber rings etc. complete assembly set as per type design inclusive of all taxes & duties, insurance, loading/ unloading & stacking FOR at site all complete as per technical Specifications and as per direction of Engineer. 150mm diameter

Making connection of drain or sewer line with existing service lines manhole including breaking into and making good the walls, floors etc. with cement concrete grade M-15 (Nominal Mix) with stone aggregate 20mm nominal size plastered with Cement Mortar 1:3 (1Cement: 3 coarse sand) finished with a floating coat of neat cement and making necessary channels etc. complete. For 250 to 300 mm dia pipes

Making connection of drain or sewer line with existing service lines manhole including breaking into and making good the walls, floors etc. with cement concrete grade M-15 (Nominal Mix) with stone aggregate 20mm nominal size plastered with Cement Mortar 1:3 (1Cement: 3 coarse sand) finished with a floating coat of neat cement and making necessary channels etc. complete. For 350 to 450 mm dia pipes

Supplying and laying following sizes one number XLPE, steel armoured, aluminium conductor power cable of 11 KV grade in existing RCC/HUME/STONEWARE/METAL/masonry open duct as required. 3C X 240 sqmm

Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminum conductor cable of 11 KV grade as required : 240 sqmm

Supplying and making STRAIGHT THROUGH cable jointing with heat shrinkable cable jointing kit including ferrule and other jointing materials, for following size of 3 core, PILC aluminum conductor cable of 11 KV grade as required : 240 sqmm

Supplying and making Earthing with G.I. earth pipe 3.0 mtr long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as required.

Supplying and making Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe, with charcoal and salt as required

Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including soldering, excavation and refilling the trench etc. as per specification.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including soldering, excavation and refilling the trench etc. as per specification.

Supply and laying of 25x6 mm GI strip along with cable and making connections firmly with accessories hard wardres etc required for completenences and as per attached specification direction of engineer ,CGPWD standards and electrical inspectorate standardsand connection

Construction of plinth for , RMU, CSS , Panels in RCC construction for installation of RMU, CSS , Panels including excavation, laying of PCC, neatly dressed, plastered, supply of all materials as required for completeness, as per attached specification/ drawing, CSPDCL standards and direction of EIC.

Supplying and erecting chain link mesh fencing for electric sub-station switch yard of 2.5 m approx. height from ground level using angle iron size 50 X 50 X 6 mm erected in C.C.foundation 15 X 15 X 40 cm deep at every 2 metre fitted with flat iron support of size 25 X 6 mm on top, bottom and mid way and chain link mesh 50 x 50 mm aparture and 4 mm dia G.I. hard wire securing and screwing with 2mm dia G.I. wire, G.I. staples, G.I.U-nails or steel pins to the angle iron at every distance of 30 cms, by iron studs complete duly painted with one coats of red oxide and two coats of approved colour paint as per CSPDCL standards and direction of EIC.

Supplying and erecting MS gate of approx. size 3.0 m (W) x 2.0 m (H) in two laps for electric sub-station switch yard fencing frame made of angle iron size 50 X 50 X 6 mm on top bottom and sides fitted with flat iron support of size 25 X 6 mm on mid way horizontaly and square bar of size 8 mm at every 100mm vertically including 3 sets of heavy duty MS hinges and aldrop complete duly painted with one coats of red oxide and two coats of approved colour paint as per CSPDCL standards and direction of EIC.

Supplying and spreading hard stone aggregate 25 mm size in out door switch as per direction of engineer -in-charge

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick G.I. plate with inscription there on, bolted/ welded to 35 mm X 35 mm X 6 mm angle iron, 60 cm long and fixing the same in ground as required.

Supplying and installation of outdoor type Transformer ONAN type with copper winding having following continuous KVA rating, 11 /0.415 KV, 3 Phase 50 Hz Vector group DYn-11, (Online tap changer) tapings in steps of ± 2.5%, ± 5%, --7.5% with oil conservator, silica gel breather having connecting terminals on HV side suitable for bare conductor/HT cable connection, cable end box on medium voltage side suitable for 1.1 KV single core UG cable(upto 300 sq mm)/bus ducting arrangment and confirming to IS:1180 Part-2 Level 3, on existing double pole structure or Brick /CC/RCC platform with all fittings, accessories, filled with filtered transformer oil including testing and commissioning etc. complete as per specification 500 KVA

Supplying and installation of outdoor type Transformer ONAN type with copper winding having following continuous KVA rating, 11 /0.415 KV, 3 Phase 50 Hz Vector group DYn-11, (Online tap changer) tapings in steps of ± 2.5%, ± 5%, --7.5% with oil conservator, silica gel breather having connecting terminals on HV side suitable for bare conductor/HT cable connection, cable end box on medium voltage side suitable for 1.1 KV single core UG cable(upto 300 sq mm)/bus ducting arrangment and confirming to IS:1180 Part-2 Level 3, on existing double pole structure or Brick /CC/RCC platform with all fittings, accessories, filled with filtered transformer oil including testing and commissioning etc. complete as per specification 800 KVA

Supplying and installation of outdoor type Transformer ONAN type with copper winding having following continuous KVA rating, 11 /0.415 KV, 3 Phase 50 Hz Vector group DYn-11, (Online tap changer) tapings in steps of ± 2.5%, ± 5%, --7.5% with oil conservator, silica gel breather having connecting terminals on HV side suitable for bare conductor/HT cable connection, cable end box on medium voltage side suitable for 1.1 KV single core UG cable(upto 300 sq mm)/bus ducting arrangment and confirming to IS:1180 Part-2 Level 3, on existing double pole structure or Brick /CC/RCC platform with all fittings, accessories, filled with filtered transformer oil including testing and commissioning etc. complete as per specification 315 KVA

Providing brick masonry work in cement mortat 1:4 (1 cement : 4 coarse sand) with well burnt clay modular bricks having compressive strength not less than 25kg/sqmm at all levels including scaffolding curing etc complete.

Plastering 15 mm thick on brick work/ CC surface with cement mortar 1:4 (1 cement : 4 fine sand) at all levels.

Supply Installation, testing & commissioning of 33/ 11 KV, 3.15 MVA power transformer with off load tap changer, copper wound, oil cooled suitable for outdoor use with fittings, accessories, both side cable end termination box, hardwares etc. as required for completeness, as per attached specification/ drawing, CSPDCL standards and direction of EIC. The unit shall be as per the attached technical specification.

Supply, Installation, Testing &; Commissioning of floor mounted SF6, motorized type (extendible type) comprising of 3nos. 12 kV, 630 A LBS for loop in and loop out to form ring main system and 1 no VCB unit shall controlled distribution transformer complete and FPI as per IS , inbuilt PT & accessories, hard wares etc. as required for completeness as per attached specification/ drawing, CSPDCL standards and direction of EIC

MAIN DISTRIBUSTION BOARD - Supplying, fabricating, installation, testing and commissioning free standing type MS powder coated cubicle three phase, 415 V power distribution/ control Type Tested Panel fabricated from 14 SWG MS sheet complete with required MS angle supports, tinned electrolytic Aluminium bus bar chamber with required rating, control switchgear and meter fixing plate, compartments for switch gear, meters and cables as per approved general arrangement plan, including 7 tank processes , approved shade powder coating, neoprene rubber gasket, internal wiring required foundation, earthing terminal, detachable gland plate, required size and rating rubber mating in front of each panel etc. as specified and shown on SLD complete with following Incomer: 1250A, 4P, 415V, ACB, 50kA - 1 No. CT’s of ratio 1250/5A - 1 Set Communication modules for BMS compatibility. “Multifunctional meter (MFM-2 as per schematic) - 1 No.” TPN Aluminium bus bars of minimum of 1250 Amps withstanding fault level of 36kA for 1 sec - 1 Set Shunt release coil of 220 V A.C as required. BUS COUPLER 1250A, 4P, 415V, ACB, 50kA - 1 No. CT’s of ratio 1250/5A - 1 Set Multifunctional meter (Type M) - 1 No. (With electrical & mechanical interlocking with incomer and DG incomer) OUTGOING – 250A, 4P, 415V, MCCB, 36kA - 3 No. CT’s of ratio 250/5A - 3 Set Multifunctional meter (Type M) - 3 No. 100A, 4P, 415V, MCCB, 36kA - 2 No. CT’s of ratio 100/5A - 2 Set Multifunctional meter (Type M) - 2 No. HVAC SYSTEM 630A, 4P, 415V, MCCB, 50kA - 1 No. CT’s of ratio 600/5A - 1 Set Multifunctional meter (Type M with harmonic measurement) - 1 No. DG INCOMER 400A, 4P, 415V, MCCB, 50kA - 1 No. Suitable for 250 kVA DG set. CT’s of ratio 400/5A - 1 Set Multifunctional meter (Type M) - 1 No. INTERLOCKING Provide electrical & mechanical interlocking between transformer incomer, bus coupler and DG incomer for break-before-make operation.

Supplying, fabricating, installation, testing and commissioning free standing type MS powder coated cubicle three phase, 415 V power distribution/ control Type Tested Panel fabricated from 14 SWG MS sheet complete with required MS angle supports, tinned electrolytic Aluminium bus bar chamber with required rating, control switchgear and meter fixing plate, compartments for switch gear, meters and cables as per approved general arrangement plan, including 7 tank processes , approved shade powder coating, neoprene rubber gasket, internal wiring required foundation, earthing terminal, detachable gland plate, required size and rating rubber mating in front of each panel etc. as specified and shown on SLD complete with following Incomer: 100A, 4P, 415V,MCCB, 36kA - 1 No. CT's of ratio 100/5A- 1 Set Communication modules for BMS compatibility. "Multifunctional meter ( MFM-2 as per schematic) - 1 No." TPN Aluminium bus bars of minimum of 100 Amps withstanding fault level of 36kA for 1 sec - 1 Set Shunt trip coil of 220 V A.C as required. Outgoings 63A, 4P, 415V, MCCB, 36kA - 4 No. CT's of ratio 63/5 Amps - 4 Set Multifunctional meter (Type M) - 4 no 32 A TP MCB & 16 A SP MCB - 4no each

Supplying and laying following sizes one number XLPE, round wire steel armoured, aluminium conductor power cable of 33 KV(E) grade in existing masonry open duct as per specification. . 3 x 300 sq mm

Supplying and making INDOOR cable end jointing with heat shrinkable cable jointing kit including lugs and other jointing materials, for following size of 3 core, XLPE aluminum conductor cable of 33 KV grade as per specification. 300 sq. mm

Supplying, fabricating, installation, testing and commissioning free standing type MS powder coated cubicle three phase, 415 V power distribution/ control Type Tested Panel fabricated from 14 SWG MS sheet complete with required MS angle supports, tinned electrolytic Aluminium bus bar chamber with required rating, control switchgear and meter fixing plate, compartments for switch gear, meters and cables as per approved general arrangement plan, including 7 tank processes , approved shade powder coating, neoprene rubber gasket, internal wiring required foundation, earthing terminal, detachable gland plate, required size and rating rubber mating in front of each panel etc. as specified and shown on SLD complete with following Incomer: 250A, 4P, 415V,MCCB, 36kA - 1 No. CT's of ratio 250/5A- 1 Set Communication modules for BMS compatibility. "Multifunctional meter ( MFM-2 as per schematic) - 1 No." TPN Aluminium bus bars of minimum of 300 Amps withstanding fault level of 36kA for 1 sec - 1 Set Shunt trip coil of 220 V A.C as required. Outgoings 63A, 4P, 415V, MCCB, 36kA - 10 No. CT's of ratio 63/5 Amps - 10 Set Multifunctional meter (Type M) - 4 no 32 A SP MCB & 16 A SP MCB - 4no each

Supplying erection testing and commissioning of hot dipped galvanised (single dip 86 micron) 30 metre High mast pole on existing RCC foundation with all accessories and equipments, main detailed as below to withstand wind pressure upto 180km/hr and minimum following specifications: a) HM shaft made of not more than 3 sections of suitable lengths with telescopic stressfit joints between sections without any circumpherencial welding, sheet thickness 4mm top, middle and bottom sections, nominal dia 600mm on bottom and 150 mm on top, base plate 32mm thick 840mm dia, PCD of foundation bolts 740mm. b) Double drum winch for lowering & raising of lantern carriage on high mast with operatable with power tool/ manual handle attachment with a torque limiting device for safe locking of carriage. c) Raising/lowering type lantern carriage designed to carry specified nos of luminaries, control gear box, junction box. d) Top pulley assemble with weather proof cover. e) 3 Nos suitable length and size stainless steel wire ropes (minimum 6mm dia and 7/19 construction) for lowering & raising of lantern carriage. f) Suitable size and length multicore flexible copper power trailing cable (minimum 3 core 4 sqmm) g) Hinged service door in base section h) Base plate earthing terminal. i) Suitable arrangement for supply distribution with termination of suitable size underground cable in high mast. j) Lightning conductor finial made of 25mm dia 300 mm long G.I.tube having single prong. k) Anchor plate of size 840x840x6mm, tem-plates 3mm thick, GI foundation bolts 16 Nos of 30 mm dia 850 mm long (EN 8 Grade) along with nuts washers etc. (RCC fooundation and luminaries will be paid separately)

Supplying, installation, testing and commissioning of 500 watt 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt.

Designing and providing suitable and approved size RCC foundation for 12-30 mere high mast including seel reinforcement form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required including laying and fixing HM foundation bolts with tam plates but excluding the cost of foundation bolts with tam plates etc complete as per specification

Design, Fabrication, Supply, Erection, Testing and commisioning of Powder coated, Weather Proof Double door type Feeder pillar fabricated out of 14 guage CRCA sheet steel in cubical, free standing, dust and vermin proof, with reinforcement of suitable size angle iron, channel, T -iron or flats as required. Feeder pillar shall be treated with all anti-corrosive process before painting as per specification. Feeder Pillar shall be suitable for 415V, 3-Phase, Four wire, 50 Hz supply complete with earth bus and lifting hooks as required in case of large panels.Approval shall be taken for each panel before fabrication. (All hardwares like nuts and bolts used shall be Galvanized and Zinc passivated) Feeder Pillar: INCOMER 1No. 63A FP MCCB(35 KA) 1No. 63A FP Contactor, AOM switch & Timers for 24 Hrs. setting Metering & Indication 1 set of phase indicating lamps BUS-BAR 1 Set of 100A TPN Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 12 Nos. 20A FP MCB & 15 NOS 6 A to 32 A MCB

Supply of hot dipped galvanized (in single dip to minimum 75 micron) octogonal pole made of 3mm thick steel grade E-350 sheet having window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with following minimum specifications with 4 way terminal connector including 4mm thick anchor plate, 4 nos 24mm dia foundation bolts of EN8 grade, and as per IS 2062 & BS EN: 10025. (designed for wind speed upto 180km/hr, IS: 875 Part 3) 9 metre high, dia 155mm at bottom and 90mm at top, base plate size 260x260x16mm, foundation bolts 750mm long

Erection of GI octogonal pole on existing cement concrete foundation having grouted bolts and nuts, aligning in true vertical position as required. 9 metre high

Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50 including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as per specification Single Over Hang 1.50 metre Long

Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt. SITC of 200W LED Flood Light

Supplying and laying double wall HDPE pipe having corrugation on the outer wall and plan surface on inner wall in ground below road, path etc at a depth not less than 40 cm including excavation, dismantling of road if required and refilling the trench etc. as required. 63 mm

Supplying and laying HDPE pipe of 4kg/cum in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification. 200 mm outer dia

Supply and drawing following sizes of FR PVC insulated copper conductor, three core cable in the existing surface/ concealed, steel/ PVC conduit as required. 3 x 1.5 sq. mm

Supply and drawing following sizes of FR PVC insulated copper conductor, three core cable in the existing surface/ concealed, steel/ PVC conduit as required. 3x4 sq .mm

Supply and drawing following sizes of FR PVC insulated copper conductor, three core cable in the existing surface/ concealed, steel/ PVC conduit as required. 6x4 sq. mm

Supply and drawing following sizes of FR PVC insulated copper conductor, three core cable in the existing surface/ concealed, steel/ PVC conduit as required. 3x2.5sq. mm

Engine :-water cooled diesel engine of suitable BHP for rated alternator at 1500 rpm, turbo charged, direct injection type, 4 stroke, 4/6 cylinder including specified size fuel tank of approved design and shape duly calibrated and painted with one coat of primer and two coats of synthetic enameled paint of approved colour, residential type silencer with exhaust MS pipe (upto 2 metre beyond silenser) duly wrapped with asbestos rope of legging of specified quality and specification.Alternator: rated at 250 KVA, 415 volts at 1500 RPM,suitable for 50 Hz 3-Phase system, AC Supply with 0.8 lagging power factor AMF Panel :Cubical, compartmentalized, AMF panel board with all suitable size power and control contactors, switches,meters and other accessories, internal wiring, connection,inter-connection etc. for trouble free smooth functioning of DG Set with power pack of 12V/24 DC as required.Base Plate : Common base plate of required size for mounting of engine alternator set fabricated from MS channel and vibration damping arrangement with cushy foot mounting i/c painting etc. as requiredAcoustic and weather proof enclosure with arrangement for fresh air intake for cooling of engine and alternator, extraction, discharging hot air in to the atmosphere as per pecifications Fuel -level information :Fuel tank shall be install with remote sensing unit for fuel tank levelwork shall be included with all civil worl like foundation ,shed of D.G set & interconnection between D.G and Main LT panel.2 year warranty and Quartly visit the D.G set for 2 year ,

Fabrication, supply, installation, testing and commissioning of cubicle type compartmentalized wall/ floor mounted power cum control panel board of specified size and depth above 300 mm and upto 450mm made out of not less than 2 mm thick CRCA MS sheet with suitable size compartments for bus bars, switchgears and necessary cutouts for voltmeters, ameters ets as per specifications including powder coating painting with busbars, switchgears and other accessories etc complete as required as per direction of Engineer INCOMER 63A, 4P, 415V, MCCB, 36kA - 1No. CT's of ratio 63/5 Amps - 1 Set Multifunctional meter (Type M) - 1no BUS-BAR 1 Set of 100A 4P Aluminium Bus Bar with colour coded PVC Sleeves OUTGOINGS 32 amps MCB TP ,440 volts-10 nos 6 to 32A SP MCB C series - 10 nos 10kA as out going feeder

UPS OUTGONG PANEL/VDB Supply, Erection, Testing and Commissioning of Indoor type UPS OUTGOING VDB/PANEL, Wall mounting type, dust and vermin proof by construction of 14 SWG CRCA sheets Compartmentalised, cable entry shall be in both top and bottom, modular type IP 42 Protection with powder coated panel as specification below. single Meters and it CT should connected in common main bus. All MCB should be 'D' curve. Incomer: 1No -100A TP+2N 26kA MCCB (Neutral should be 200% of the Phase Current) 1Sets of Current transformer rated 63/5A, 10VA/CI 1.0 for metering at common bus. 1No – Digital Multi data Meter with RS 485 (suitable to measure harmonics) at common bus. 1 Sets – LED type RYB indication lamps with control fuses Outgoing: 8Nos - 40A TP+2N MCB 16kA 100A TP+2N Copper Bus Bar and Associated Accessories as required. (Neutral should be 200% of the Phase Current) Incoming and outgoing cables shall be of Top& Bottom entry.

VTPN DB-DISTRIBUTION BOARD - Supply,installation, testing & commissioning of following MCB/MCCB double door type prewired Vertical Distribution boards as per drawing & specification fabricated out of 16 SWG CRCA sheet steel in compartmentalized design as per specification and drawings. These distribution boards shall be surface/ recessed in walls. All outgoing from DB shall be propoerly labelled. The rate includes the painting, numbering earthing etc. as required. DB shall be suitable for incoming aluminium armourd cable,as per requirement , standard specification and as directed by Engineer in-charge. 8 Way VTPN DB Comprising of following with ELCB: Incoming:- One (1) No. 100 A FP MCCB(10KA) Outgoing:Two (6) Nos. 63A TPN MCB(10KA)

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)Short Point

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Medium Point

Wiring for light/ fan/ exhaust fan / call bell point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Long Point

Wiring for twin control light point with 3x1.5 sqmm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) with 5/6 amp modular switch, modular base and cover plate, suitable size G.I. box as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Extra for providing and fixing light plug point on board in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) point wiring with modular type 3 pin 5/6 amp socket outlet and 5/6 amp switch including cost of base and cover plate and G. I. box etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Short Point

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Medium Point

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Long Point

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point I

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point II

Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point III

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Short Point

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Medium Point

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Long Point

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point I

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point II

Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point III

Wiring for power plug point with 3x6 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Short Point

Wiring for power plug point with 3x6 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Medium Point

Wiring for power plug point with 3x6 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Long Point

Wiring for power plug point with 3x6 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point I

Wiring for power plug point with 3x6 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 32 Amp SPMCB "C" curve and 6 pin 20 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) Extra Long Point II

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 3 X 1.5 sq. mm in 20mm conduit

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 3 X 2.5 sq. mm in 20mm conduit

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 3 X 4 sq. mm in 25mm conduit

Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, wire in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5) 3 X 6 sq. mm in 25mm conduit

Supplying and fixing 2 pole and earth, 240 volts, industrial type, socket outlet, enclosed metal plug top along with SP MCB in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as per specification. 20 Amp with “C” curve MCB

Supplying and fixing 2 pole and earth, 240 volts, industrial type, socket outlet, enclosed metal plug top along with SP MCB in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as per specification. 32 Amp with “C” curve MCB

Supplying and fixing TPN and earth, 440 volts, industrial type, socket outlet, enclosed metal plug top along with MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as per specification. 20 Amp with “C” curve TP MCB

Supplying and fixing TPN and earth, 440 volts, industrial type, socket outlet, enclosed metal plug top along with MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as per specification. 32 Amp with “C” curve TP MCB

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification. 100mmX75mm (3 Module)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification. 125mmX75mm (4 Module)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification. 200mmX75mm (6 Module)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification. 125mmX125mm (8 Module)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as per specification. 200mmX150mm (12 Module)

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as per specification. 3 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as per specification. 4 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as per specification. 6 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as per specification. 8 Module

Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as per specification. 12 Module

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 watt {4 feet}

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 36 watt {4 feet}

Supplying, installation, testing and commissioning of following LED tube light fitting including batten with Electronic Driver Heat sink Capacitor complete with all other accessories on surface/ in false ceiling, including connection, earthing etc complete as per specification and IP20, P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 10 watt {2 feet}

Supplying, installation, testing and commissioning of following sizes ceiling fan including wiring the down rods of standard length up to 30 cm with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, earthing etc. complete as required. P.F. should be greater than 0.9, with BEE Star rating from 3 star and above, IS: 374:2019 including all amendments. 1200 mm sweep

Supplying, installation, testing and commissioning of following sizes fancy exhaust fan having built in louvers in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 225 mm sweep

Supplying, installation, testing and commissioning of following sleek LED panel down lighters (luminaries) in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 36 watt, size 600 x 600mm

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete shall be made up of die cast power coating housing complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 Watt

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete shall be made up of die cast power coating housing complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt.. 9 Watt

Supply and fixing of metal box of following sizes in recess with suitable size phenolic laminated sheet cover in FRLSont including painting, accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 100mm x 100mm x 60mm deep

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, including connection, earthing etc. complete as per specification.

Supplying and fixing of wall/ cabin fan including connection etc. as per specification. P.F. should be greater than 0.9 300 mm sweep

Supplying, installation, testing and commissioning of following izes mediaum duty (continuous running)1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as per specification. P.F. should be greater than 0.9 300 mm sweep

Supplying and fixing following sizes of down rod of 15/20mm dia M.S. pipe of thickness 2 mm to ceiling fan including painting with matching colour etc. as per specification. 90 cm long

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 12 Watt

Supplying, installation, testing and commissioning of following LED fitting (luminaries) down lighters in round/ square shape complete with electronic driver heat sink capacitor and all other accessories on surface/ in false ceiling etc. as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 100 lumens /watt. 18/20 Watt

Supply and fixing of following sizes PVC conduit in concealed manner along with accessories, hardwares etc required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 20mm

Supply and fixing of following sizes PVC conduit in concealed manner along with accessories, hardwares etc required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 25mm

Supply and fixing of following sizes PVC conduit in concealed manner along with accessories, hardwares etc required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 32mm

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3 pin 5/6 amp socket outlet

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 6 pin 15/16 amp socket outlet

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. Fan Regulator Electronic, step type moving all round

Supply and fixing of following modular type switches and accessories of approved make and type such as switch, socket etc on the existing modular plates & switch box including connections along with accessories, hardwares etc required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 5/6 amps one way switch

Supply and fixing of round/hexagonal fan box (125mm dia) depth 75mm (max.) with 12mm dia steel bar hook,1.6mm thick MS sheet cover, in RCC slab along with accessories, hardwares etc as required for completeness and as per direction of Engineer, CGPWD standards and Electrical Inspectorate standards.

Providing and fixing fan clamp made of 3mm thick MS flat on existing iron trusses/ girder including necessary bolts and nuts etc. as per specification.

Supplying and fixing of wall/ cabin fan of 400mm sweep including connection etc. as required

Supplying, installation, testing and commissioning of following sizes heavy duty (continuous running) 1400 rpm exhaust fan in existing opening in wall including earthing etc. complete as required. 300 mm sweep

Providing and fixing composite unit for computer points having modular type 1 No 6 pin 16 amp socket outlet, 1 No 16 amp switch, 3 Nos 3 pin 6 amp socket outlets, 3 Nos 6 amp switches, suitable G.I. box, base and cover plates, earthing the sockets and switch box including etc. as per specification.

Supplying and fixing of GI Trunking/Raceways with 120 GSM coating and made up of 1.6 mm thick steel sheet. The steel sheet is Pre Galvanized with zinc coating and is double folded and arc welded in the joints to prevent concrete seepage. The trunking is compartmentalized for provision of data, power and voice cables and has a depth of 25/38mm complete as per specification. : Raw materials complies to Indian Standards IS 277:2003. 250 mm x 25 mm x 1.6 mm (3 compartments)

Supplying and fixing of Crossover boxes, suitable for 25/38 mm depth GI raceways. The crossover boxes are made out of high pressure die cast zinc alloy complete with all accesseries such as trap lid, strong support frame, bore support studs etc. Complete as per specification.The crossOver box should have in-built flyovers to segregate power, data and voice cables during distribution and routing. Trap lid is reinforced and can withstand upto 2 tons of distributed load on the top. As per IEC 61084 Standards. 250 mmx 250 mm x 60 mm - 75 mm (3 compartment)

Design, manufacture, supply & installation of following UPS’s (Input - three phase and Output -three phase) unit as per specifications, Cost to be inclusive of wires, Cables, Jointing and termination of wires and cables and all related accessories required to complete the installation to satisfaction of Engineer incharge 15 KVA/12KW UPS including battery bank with 30 Minutes Battery Backup And Rack As per requirement

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, 4cx16 mm copper cable

Supply of hot dipped galvanized (in single dip to average 65micron) octoganal pole made of 3mm thick steel sheet having window and flush cover with locking arrangement at suitable height from base for cable termination block, pole suitably reinforced with welded steel section at window cut section to make the strength of pole unaffected, with following minimum specifications including 3mm thick anchor plate, 4 nos 20mm dia foundation bolts of EN8 grade. (designed for wind speed upto 150km/hr) 7 metre high, dia 130mm at bottom and 70mm at top, base plate size 220x220x12mm, foundation bolts 700mm long

Designing and providing suitable RCC foundation in Cement Concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) for 3 mere to 12 metre high GI octagonal pole including steel reinforcement (minimum 90kg per cum), form work, embeding 2 nos 50mm dia PVC pipe for cable entry in each foundation, excavation disposal of surplus soil and curing etc. as required

Erection of GI octogonal/ tubular pole on existing cement concrete foundation having grouted bolts and nuts, aligning in true vertical position as required : 7 metre high

Supply and fixing following street light pole bracket on existing pole made out of 50 mm dia MS "B" class pipe welded to 300 mm long MS pole canopy of suitable dia at a angle of 102.50including having MS triangular stiffner of size 150 X 50 X 5 mm thick, making arrangement for tightening the bracket with pole by providing suitable size heavy duty nuts and bolts in canopy, painting with one coat of approved steel primer etc. as required Single Over Hang 1.00 metre Long

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required. 4 x 16 sq. mm. (for area lighting)

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required. 4 x 16 sq. mm. (for area lighting)

Supplying and making end termination with brass compression gland and aluminum lugs for following size armoured aluminum conductor power cable of 1.1 KV grade as required. 4 X 16 sq. mm

Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with gear box, igniter, with IP 65 protection on pole bracket complete . 60watt ( +/- 5 % W)

Supplying, installation, testing and commissioning of following 230/250 volts LED street light fitting with all accessories like driver, heat sink made of die cast aluminium with IP 66 protection and 15 KV surge protection on pole bracket, including connection, earthing, Separate housing for driver etc complete as per specification and P.F. should be greater than 0.9. LED chip efficacy ratio ≥ 120 lumens /watt. 120Watt

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X400 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X240 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X 150 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X70 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X50 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 3.5C X25 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 4C X10 sqmm

Supplying and laying following sizes one number PVC insulated/ XLPE, PVC sheathed, steel armoured, aluminium conductor power cable of 1.1 KV grade in existing RCC/ HUME/ STONEWARE/ METAL/ HDPE pipe as required 2C X10 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3.5x240sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3.5x150 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3.5x70 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3.5x50 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 3½ X 400 sq. mm (70 mm)

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 4x25 sqmm

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 2 X 10 sq. mm (19 mm)

Supply and making of end termination with brass compression gland and aluminum lugs for following sizes armoured aluminium conductor power cable of 1.1KV grade along with accessories, hardwares etc. required for completeness and as per attached specification, direction of Engineer, CGPWD standards and Electrical Inspectorate standards. 4x 10 sqmm

Supplying and fixing on surface/ recess prewired horizontal type (4+12)double door, 415 volts TP&N, MCB distribution board of sheet steel phosphatized and powder painted complete with loose wire box, terminal blocks, 200 amps tinned copper busbar, common neutral link, earth bar, din bar, detachable gland plate, loose wire box, superior make terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks including interconnections, earthing etc. as required

Supplying and fixing on surface/ recess prewired horizontal type 6 way (4+18)double door, 415 volts TP&N, MCB distribution board of sheet steel phosphatized and powder painted complete with loose wire box, terminal blocks, 200 amps tinned copper busbar, common neutral link, earth bar, din bar, detachable gland plate, loose wire box, superior make terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks including interconnections, earthing etc. as required

Supplying and fixing on surface/ recess prewired horizontal type 8 way (4 + 24), Double door, 415 volts TP&N, MCB distribution board of sheet steel phosphatized and powder painted complete complete with loose wire box, terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks including interconnections, earthing etc. as per specification. (But without MCB/ RCCB/ Isolator)

Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6-32A SP MCB C series 10kA as out going feeder.

Supplying and fixing TP MCB, 440 volts, 'B' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 40 A-63A

Supplying and fixing DP MCB, 240 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 40 amps

SITC of, 60Watts Wall Speaker System Weather Resistant PA Wall Speaker Reliable IP-66 rated, weather resistant plastic cabinet wall speaker with outstanding sound clarity. Suitable for both indoor and outdoor use. Suitable for use on 100V line, or on direct 8 ohm impedance. 60W/8Ω; 30W/100V Power Taps on 100V 30/15/7.5W Frequency Response 95-20,000Hz SPL at 1kHz (1W/1m) 87dB Speaker Woofer 163mm (6½”), Tweeter 25mm (1.0”)

SITC of, 40Watts Weather Horn Speaker System 2-way high efficiency, high fidelity PA Music Horn Input Power 40W RMS Power Taps 40/20/10/5W Impedance 250/500/1k/2kΩ Frequency Response 120-16,000Hz SPL at 1kHz 98dB/1W/1m; 114dB/40W/1m

SITC of, Remote zonal paging console that works with paging controller for remote paging and control over a multi-zone system. Several modes (all zones, 10 zones or individual zones) can be achieved through this paging console. Capability to page upto 300 zones.Capability of cascading (series connection with RJ 45) up to 16 microphones for paging from multiple locations. Operation number input keys with LED display. Input MIC: 600Ω,10mV, unbalanced, Line:10kΩ,775mV, unbalanced Output Balanced Frequency Response MIC:100Hz~15KHz; Line: 30Hz~18KHz S/N Ratio MIC input: 60dB Line input: 80dB

SITC of, 600 WATTS PA Power Amplifier 1x Line 200mV unbalanced input and 2xLine 1V balanced inputs through XLR connector, one 1V input having priority over all other inputs. 100V input is provided for connecting another amplifier’s output in long line applications Power Output 750W Max., 600W RMS at 10% THD, 550W RMS at 5% THD, 500W RMS at 2% THD, 480W RMS at 1% THD Output Regulation ≤ 2 dB, no load to full load at 1kHz Input Channels 1 × 200mV/470kΩ (unbal.), 2 × 1V/50kΩ (bal.), 1 × 100V Input/50kΩ Frequency Response 50-15,000Hz ±3dB Signal to Noise Ratio 60dB Tone ControlsBass: ±10dB at 100Hz, Treble: ±10dB at 10kHz Outputs Loop through 1 × 200mV/600W, 2 ×1V/1kW Speaker Outputs 4Ω, 8Ω, 70V & 100V Power Supply AC: 220-240V 50/60Hz DC: 24V (2×12V Car Battery)

SITC of, PA Audio Splitter AC Operation, line level signal splitter. Accepts Line Level Stereo as well as Mono inputs through F/XLR connector as well as 6.3mm (1/4”) stereo phone jack sockets. Provides four stereo balanced outputs or eight mono balanced outputs through M/XLR connectors. Individual volume control for each input & output channel. Input Channels 2 × 100mV/20kΩ Balanced Outputs 8 × 1V / 50Ω Balanced Frequency Response 20-20,000Hz ±3dB Distortion <0.1% Signal to Noise Ratio 70dB

SITC of, 2.5 Sq mm 2 Core Twisted Copper Speaker Cable Armoured Type with Cabling in PVC Conduit

Outdoor Audio Junction Box ,Size in mm 1200(H)x600(D)x900(W) Metal Sheet, (Construction- Welded Galvanized Plain Steel Construction 1.2 mm Thick Load Bearing angles are 1.5 mm, Dual Door- Dual locking option ,2 nos. cooling Fan for hot air execution, 2 Pair heavy duty vertical mounting rail for equipment mounting and required Shelfs , Power Manager, MCB, etc

Audio Equipment Rack,Size in mm 1800(H)x600(D)x1200(W) Metal Sheet, (Construction- Welded Galvanized Plain Steel Construction 1.2 mm Thick Load Bearing angles are 1.5 mm, Dual Door- Dual locking option ,2 nos. cooling Fan for hot air execution, 2 Pair heavy duty vertical mounting rail for equipment mounting and required Shelfs , Power Manager, MCB, etc

SITC of Connectors & Patch Chord

Supply, Installation, Testing and Commissioning of 2MP Bullet/Dome Camera-Providing installation testing and commissioning weather & dust proof IP based Fixed Lens true day / night Camera (IP67), 1/2.7" CMOS Image Sensor, Max 25/30 fps@4Mp; Number of Pixels: 2560 (H) × 1440(V); H.265 and H.264 Triple Stream Encoding: Main Stream: 4MP/3MP/1080P(1-25fps) Sub Stream: 720P (1-12fps) / D1 (1-25 fps) / CIF (1-25FPS); tHIRD sTREAM d1/cif/480X240(1-25FPS) WDR - Digital, Auto Day/Night, 3D DNR, BLC, HLC , 2.8-12.00 mm Motorized Focussed Zoom, Motion Suppot, IR Range of 30 -50 Mtrs, Micro SD Card slot, PoE,12VDC; CE, FCC, RoHS Certified

Supply, Installation, Testing and Commissioning of 16 Channel NVR 2 Sata port-Upto 12 TB; 32 Channel IPcamera input, Quad Core embedded Processor and LINUX Embedded; No POE; Max 200 Mbps incoming & outgoing bandwidth, Smart H.265/ H.264 codec decoding, Upto 8 MP resolution preview and playback, Frame Rate: 1-15 FPS(8 MP); 1-25/30 fps for rest of Resolutions; Support 2 SATA HDDs up to 12 TB each, 2 USB (1 USB3.0,1 USB2.0), 1HDMI /1 VGA simultaneous video output , Two way talk 1Channel Input, 1Channel Output RCA, 1RJ-45port (10/100/1000Mbps),

SITC of 55-inch LED Display, Type 120 HZ LED Direct BLU Resolution 3840 X 2160 4K UHD (16:9), Pixel pitch (mm) 0.315 mm (H) x 0.315 mm (v), Viewing Angle: (H/V) - 178/178, Brightness 300 nits, Contrast Ratio 4000 :1, Response Time: 8ms; Operating Hour: 16/7; Haze:2%, Builtin speaker(10 W +10 W), inputs : Analog HDMI 2.0(2),HDCP 2.2, Audio-Stereo Mini Jack, HDMI/Audio (Common), USB 2.0 x1, Output: Audioi - Stereo Mini Jack; Ethernet/RS-232 external control thru stereo jack, RJ45 etc with wall mounting bracket.

Supplying, installation, testing and commissioing of 8 Port industrial PoE Switch-10/100/1000 8 Port with 2 Giga SFP uplink,industrial PoE Switch support dual DC power backup.

Supplying, installation, testing and commissioing of 6U Indoor Rack Wallmount 6U 450D With Front Glass Door Lock & Key 550 4U-(fan +PDU+Cable Manager)

Supplying, installation, testing and commissioing of 4U Indoor Rack Wallmount 4U400D With Front Glass Door Lock & Key 5506U-(fan +PDU+Cable Manager)

Supplying, installation, testing and commissioing of 8 TB Surveillance HDD

Supplying and drawing UTP4 pair Cat 6 LAN wire inexisting surface/ concealed Steel/FRLSPVC conduit as per specification

Supplying and drawing 4 pair 0.5 mm FR PVC insulated copper conductor, unarmored telephone cable in the existing surface/ concealed steel/ PVC conduit as required.

SITC of RJ-11 Telephone jack type socket with box and plate complete

SITC of T.V antenna socket out let

Supplying and drawing RG-11 grade co-axial TV cable PVC insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ concealed steel/ PVC conduit as required

Supply, Installation, Testing and Commissioning of ongrid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mounted on Aluminium/GI structure of suitable strength with following components complete as required:- a) Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India,conforming to IS 14286/IEC 61215, IS/IEC 61730-Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than 16.5%. PV modules used in solar power plants/ systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end of 25 years. b) Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 400 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 degree C. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d) Fixing of Array junction box & Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1 kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required.

Supplying and fixing on surface/ recess prewired horizontal type 12way (4 + 36), Double door, 415 volts TP&N, MCB distribution board of sheet steel phosphatized and powder painted complete complete with loose wire box, terminal blocks, tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, duly prewired with suitable size FRLS PVC insulated copper conductor up to terminal blocks including interconnections, earthing etc. as per specification. (But without MCB/ RCCB/ Isolator)

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 1 No. 40A 4pole MCCB

Supplying and fixing TP&N MCB, 440 volts, 'C' curve, suitable for lighting and other loads in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 1 No. 63A 4pole MCCB

Supplying and fixing SP MCB, 240 volts, 'C' curve, suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as per specification. 6 amps to 32 amps

Supplying and installing following size powder coated, perforated M.S. cable trays with perforation not more than 17.5% rigidly suspended from the ceiling with M.S. suspenders at a distance not more than 2.5 metre and near every junction/ joint etc complete as per specification. 225 mm width X 50 mm depth X 1.6 mm thickness

Supplying and fixing of following sizes powder coated, perforated, M.S. cable trays bends (horizontal) turning at 900 in same plane with perforation not more than 17.5% rigidly jointed with cable tray etc. complete as per specification. 225 mm width X 50 mm depth X 1.6 mm thick

Supply, Installation, Testing and Commissioning (SITC) of 12kV Shunt Capacitor Bank of 1200 kVAR capacity, complete in all respects for efficient power factor improvement and reliable operation. The scope shall include supply and erection of capacitor units, suitable mounting structure/stand, discharge resistors, Residual Voltage Transformers (RVTs), Current Transformers (CTs), APFC relay for automatic power factor correction, protective relays, and interconnecting aluminium/copper bus bars. The panel shall be provided with digital multifunction meter (V, I, kVAR, PF, frequency), necessary indicating lamps for ON/OFF/healthy status, and annunciation system for faults such as capacitor failure, unbalance, over-voltage, under-voltage, and over-current conditions. The work shall also include control wiring, power cabling, terminal blocks, ferrules, glands, lugs, earthing arrangement, and all required accessories and hardware for complete installation, testing, and commissioning of the system. Proper protection, switching, and automatic step control of capacitor bank shall be ensured through APFC relay. The entire work shall be executed in accordance with approved drawings, attached technical specifications, CSPDCL standards, Electrical Inspectorate norms, and as directed by the Engineer-in-Charge.

Luxalon® Aluminium Screen ceiling - V 100 , Module > 200mm : Providing and fixing of Luxalon® V 100 Plain Aluminium panel ceiling manufactured by M/s Hunter Douglas India Pvt. Ltd. of approved White colour consisting of panel 101 mm deep X 0.6 mm thick, panel length upto 6 mtr, Coil Coated on a Continuous Paint Line, Double baked and roll formed from enamelled corrosion resistance Aluminium alloy AA 5050 (Al. Mg) for higher strength and good roll forming characteristics. Panels shall be clipped to a baked enamelled Aluminium panel carrier of 30 mm wide x 90 mm high x 0.95 mm thick made from Aluminium alloy AA5050 (Al. Mg) White Satin/Black Satin, one leg of the carriers with cut outs to hold the panels in a module of 200 mm., at a distance of 2.10 mtr. Panel carrier shall be suspended by means of threaded rod at a distance of 2.0 mtr c/c. Paint Finish: Aluminium panels shall be chromatised for maximum bond between metal and paint enamelled twice under high temperature, both sides with a full primer and finish coat on a Continuous Paint Line. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights, diffuses, columns etc. Approved Make : Hunter Douglas, Gordon & Chicago Metal.

Providing and laying MFMA (Maple Flooring Manufacturers Association) approved hard maple wood sports flooring, complete as per approved drawings, manufacturer’s specifications, and directions of the Engineer-in-Charge. The work includes supply and installation of 20 mm thick hard maple wood flooring (USA) with MFMA certification marking. Boards shall have minimum 57 mm width and random lengths 230–1800 mm, machine-milled and tongue & groove jointed on all sides for proper alignment and finish. The flooring shall be laid over a substructure of seasoned Spruce/Pine sleepers (63 × 38 mm) fixed perpendicular at 305 mm c/c, supported on 19 mm rubber shock pads at 305 mm c/c for resilience and load distribution. A 0.20 mm polyethylene vapour barrier shall be laid over the prepared concrete base to prevent moisture ingress. The surface shall be machine sanded and finished with two coats of oil-modified polyurethane sealer and one coat of polyurethane sports finish. Game line marking shall be done as per approved drawings and standards. The system shall comply with standards of Badminton World Federation, FIBA, International Handball Federation and World Squash Federation. Rate includes Gymnastic sleeves provision, all materials, labour, substructure, vapour barrier, finishing, line marking, transportation, taxes, and all incidental charges complete.Make :- Action USA, Connor USA, Juncker

Providing and fixing in position Laser cut MS powder coating/ galvanized sheet 5 mm thick for exterior work as per approved design & pattern as detailed drawing i/c all fitting. Complete all as per Specification & direction of Engineer-In-Charge. ( Frame work to be paid separately)

Elastic Swing floor "Moscow" 14x14m FIG-certified, ORIGINAL REUTHER Sub-construction made of 15 mm high waterproof plywood sections: 50 sections 120 x 240 cm, 20 sections 100 x 240 cm and 4 sections 100 x 100 cm. The floor is equipped with 2270 high quality tempered steel springs. 7 oor mats 14 x 2 x 0.07 m are composed of 196 puzzle shaped foam plates (5 cm high) and special foam covered with needle fleece (2 cm high). Mats are linked together by 6 “Duo Velcro” straps. 4 white straps are available for marking the competition area.

Vaulting - Set of Mats International 3 mats 300 x 200 x 20 cm incl. 2-part protective padding of the base of aprox. 100 x 120 x 20 cm

Landing Mat "Happy Landing" with Marking Size 600 x 200 x 10 cm. For vaulting incl. marking o anding zone acco rding to latest FIG norms. PVC cover, blue, with zipper.

Vaulting Table "Ergojet Rio" for Pit FIG certied, ORIGINAL REUTHER The new height adjustment system with gas springs enables an easy and quick height adjustment from 100 - 140 cm in increments of 5 cm. To provide greater safety the height adjustment is fixed on the side. Weight without safety padding: 135 kg. Floor space required: 110 x 94 cm. The transport system is included.

Run-Up and Jumping Device ORIGINAL REUTHER Consisting of Run-up track 1 m wide,25 mm thick. Anti-slip springboard a nd table zone, distance indicator,measuring tape and role up core. The runway is covered with a comfortable needle felt carpet. Total length 25 m. Widt h 100 cm. (”Ergojet Rio”, springboard and landing mat are not includ ed).

Rondat Mat -long Version- Springboard safety collar. Lightweight high-density foam constructio n. Reinforced PVC cover in contrasting colour for increased safety. Mandatory at FI G competitions. Size 140 x 120 x 22 cm.

Hand-Safety Mat Use of the hand safety mat is allowed at o cial FIG Competition s. This mat is also very useful as a support during methodical training. Made of skin-friendly, washable material. Size 120 x 100 x 3 cm..

Springboard "Moscow 5" FIG-certied, ORIGINAL REUTHER Soft Version according to FIG-norms. Equipped with revolutionary “Whisper Spring System”. 5 conical temp ered steel springs. Surface is made of hybrid carbon ber sandwich, with 20 mm high densit y foam and with comfortable long-lasting needle eece.

Springboard "Moscow 8" FIG-certied, ORIGINAL REUTHER Hard Version according to FIG-Norms. Equipped with revolutionary “Whisper Spring System”. 8 conical temp ered steel springs. Surface is made of hybrid carbon ber sandwich, with 20 mm high densit y foam and with comfortable long-lasting needle eece.

FIG certified, ORIGINAL REUTHER Competition Parallel Bars “Melbourne Pro” with innovative “Dynamoflex Pro” fiberglass rails Optimal vertical dynamics for gymnastic elements between the rails and high horizontal stability for elements performed sideways on one rail Dynamoflex Pro: The unique pre-tension of rails offers gymnasts great dynamics for flight elements and simultaneously reduces impact forces of landings on the arms. The natural fiber veneer provides excellent grip even when new, reduces magnesium consumption, and shortens preparation time. Additionally, it extends the lifespan of the rail surface even under high usage intensity. Stepless width adjustment with measuring scale: Enables quick and repeatable individual adjustment of the Parallel Bars. (Optional) Integrated wheel system: The Parallel Bar can be placed on floor-friendly rubber wheels and moved to the desired position in just a few simple steps.

Parallel Bars "Melbourne"- Set of Mats International 2 mats 300 x 200 x 20 cm 1 mat 300 x 70 x 20 cm (Center Mat) 4 mats 100 x 135 x 20 cm 2 mats 300 x 200 x 20 cm with cuts 1 mat 100 x 200 x 20 cm

Parallel Bar Training Pad Can be divided/ connected in the middle via Velco-connection. Made of Blue PVC-cover. Fixation with Velcro. Delivered in two pieces a 70 cm long.

Power and Coordination Trainer The basic positions, based on the so-called ”C”, ”I” and ”S” positions, can be simulated and brought to perfection. The metal feet support and nylon belt are comfortably upholstered.

Parallel Bars "Junior" ORIGINAL REUTHER With stable frame and glued plywood rails, length 280 cm. Height adjustment from 105 to 165 cm, with 5 cm increments. Continuous width adjustment from 30 to 50 cm. Frame mat can be ordered separately. With floor plate and with transport item.

Frame Mat for Parallel Bars "Junior" Size: 300 x 60 x 20 cm

Landing Mats "Happy Landing" With PVC-cover and zipper. Size: 200 x 200 x 10 cm

Pommel Horse FIG-certified, ORIGINAL REUTHER 2-leg base with height adjustment from 95 to 125 cm. Equipped with 2 hygroscopic aluminium pommels, tie-down chain with tension shackle for floor anchoring, 4 built-in retractable swivel rolls and outside lever control.

Pommel Horse - Set of Mats International 4 mats 200 x 200 x 10 cm with cuts for the base.

Safety Padding for Pommel Horse (Set) One Set is needed for one Competition Pommel Horse.

PVC Cover for Pommel Horse Covers the Body and the Pommels. Color: blue

Pommel Horse "Junior" For young gymnasts up to approx. 14 years. The height and size of the trunk and wooden pommels are proportionally smaller (90%). Height: 100 cm. Body: 143 x 32 cm.

Pommel Horse - Set of Mats International 4 mats 200 x 200 x 10 cm with cuts for the base.

Floor Pommel Horse This trunk, upholstered with top quality leather, is identical to the trunk of the competition pommel horse.Provided with 2 adjustable and removable aluminium tube pommels, covered with hygroscopic anti-slip rubber compound. Height 35 cm.

Mushroom Mushroom on a wooden base, without pommel. Height 48 cm. Diameter 60 cm.

Mushroom with Pommel Same as Art. 1395014, but with 1 Aluminium Pommel. Diameter 60 cm.

Tumbling Track "Moscow" Developed on the basis of the FIG certified Elastic Swingfloor "Moscow“, high quality water resistant plywood elements each 120 x 200 cm with new spring system, covered with puzzle shaped foam pieces each 100 x 100 x 5 cm and door mat made of special high quality foam with needle fleece. Total height: 20 cm. Tumbling Track "Moscow" 18 x 2 m, 15 elements

Balance Beam "Soft Touch" FIG certified, ORIGINAL REUTHER The revolutionary new SPIETH "Soft Touch" technology features a unique combination of landings with a "Soft Touch" and superior stability and can decrease impact forces of up to 50%. Height adjustable from 75 to 125 cm in 5 cm increments. Length: 500 cm.

Competition Safety Padding (per Piece) Special padding for Balance Beam legs to prevent injuries. 2 pieces are needed for one Balance Beam. In accordance with the latest FIG guidelines.

Beam Protection Pad Length: 2 m.

Multi Mat for Balance Beam Soft safety mat with a high level of shock absorption mad e from high quality memory foam. Size: 150 x 100 x 1,5 cm

Balance Beam - Set of Mats International 3 mats 300 x 200 x 20 cm 1 mats 100 x 200 x 20 cm 1 mats 200 x 200 x 20 cm 4 mats 250 x 200 x 20 cm with cuts 4 mats 135 x 100 x 20 cm

Soft Touch Length: 5 m. Width: 10 cm.

Uneven Bars "Munich" FIG-certied, ORIGINAL REUTHER New Competition Uneven Bars with "Fiber ex Pro" rails and built -in height adjustment system. New standard heights according to the current FIG standard: low rai l 175 cm, high rail 255 cm. . With patented double tension system including 2 slide adjusters pro viding the individual ne turning of tension. Adjustments: low rail from 150 to 200 cm, high rail from 230 to 280 cm, di stance between the rails max. 195 cm.

COMPETITION MAT SETS "MOSCOW" Sets of mats for FIG competitions, FIG-certified. Mats with velour carpet in spiethblue colour and additional edge st abilization and are xed together by means of velcro. Uneven Bars - Set of Mats International 4 mats 300 x 200 x 20 cm 1 mat 200 x 200 x 20 cm

Happy landing mats Size: 200 x 200 x 10 cm

Coach Platform "Club" For Uneven Bars and Horizontal Bar. The platform of 140 x 50 cm, height-adjustable from 131 to 191 cm in 10 cm steps, can be xed in two positions. Self retracting mechanism through a gas spring. Requires oor anchoring (without xing material).

TCS - Tension Control Sensor Prevention of too high or too low tensioning with flashing light signal and digital display. Including battery charger, storage case and shortcuts to adapt the tension cable. Per tensioned gymnastics apparatus one TD is required.

Uneven Bars “Kombi” with “Fiberflex Pro” rails Special design of a competition Uneven Bars for training purposes Thanks to the quick-lock system, it can also be used as a Horizontal Bar (1-rail module) and can easily be converted Two rails are included in the scope of delivery

COMPETITION MAT SETS "MOSCOW" Sets of mats for FIG competitions, FIG-certified. Mats with velour carpet in spiethblue colour and additional edge st abilization and are xed together by means of velcro. Uneven Bars - Set of Mats International

Happy landing mats Size: 200 x 200 x 10 cm

Coach Platform "Club" For Uneven Bars and Horizontal Bar. The platform of 140 x 50 cm, height-adjustable from 131 to 191 cm in 10 cm steps, can be xed in two positions. Self retracting mechanism through a gas spring. Requires oor anchoring (without xing material).

TCS - Tension Control Sensor Prevention of too high or too low tensioning with flashing light signal and digital display. Including battery charger, storage case and shortcuts to adapt the tension cable. Per tensioned gymnastics apparatus one TD is required.

Ring Frame "Berlin" FIG certified, ORIGINAL REUTHER Built-in shock absorbers and additional special spring system reduce the jolt on the joints and also the peak forces. Safety frame made of square steel tubing with individual components with a maximum length of 270 cm for easy transportation . Height adjustment in steps of 5 cm from 592,5 - 612,5 cm. The plastic-encased ropes for rings are attached by means of variable threaded sockets with a Fine adjustment. Double cable tension system together with the licensed key adjustment provide the device with great stability.

Still Ring Frame - Set of Mats International 1 mat 300 x 200 x 20 cm 2 mats 100 x 200 x 20 cm

Trainer Platform "Club" for Rings Height adjustable trainer console for use with rings. The board of 13 5 x 45 cm is covered with anti-slip material. Because of nitrogen gas loaded springs, the board automatically tips up when the gymnast or coach steps down. Height adjustable from 131 to 191 cm with 10 cm increments. The stairs can be installed on three sides of the console. The trainer console should be bolted to the floor.

High Bar "Stuttgart" for Pit FIG certified, ORIGINAL REUTHER With antifracture safety bar of stainless steel, adjustable from 260 to 295 cm, double cable fixing system with 2 safety slide adjusters.

Horizontal Bar - Set of Mats International 4 mats 200 x 300 x 20 cm 2 mats 200 x 300 x 20 cm with cuts

High Bar "Club" The height of the rail can be quickly adjusted from 80-250 cm with 10 cm increments and from 250-290 cm with 5 cm increments. With fast tension releaser. The rail is easily interchangeable with uneven bar rail "Carbo ex" (Art. 2202205) and uneven bar rail "Fiberlex" (Art. 2204825).

Horizontal Bar - Set of Mats "Basic" International 4 mats 200 x 300 x 20 cm 2 mats 200 x 300 x 20 cm with cuts

Coach Platform "Club" For Uneven Bars and Horizontal Bar. The platform of 140 x 50 cm, height-adjustable from 131 to 191 cm in 10 cm steps, can be xed in two positions. Self retracting mechanism through a gas spring. Requires oor anchoring (without xing material).

High Bar "Stuttgart" FIG certified, ORIGINAL REUTHER With antifracture safety bar of stainless steel, adjustable from 260 to 295 cm, double cable fixing system with 2 safety slide adjusters.

Uneven Bars "Kombi" - with "Fiberflex Pro" Rails for Pit

Competition Trampoline "Ultimate" 4x4 (incl. Lifting Roller Stands) FIG-certified. The new developed trampoline with modied and most powerful jum ping bed of 4 x 4 mm wide weaved nylon bands. Frame: Flat-oval steel tube 520 x 305 x 115 cm made of special steel; galvanized incl. shock absorbing and stable frame pads.

Trampolin Safety Spotter Mat "SECURA " Size 175 x 125 x 14 cm, reinforced PVC cover with stretch material top, 4 handles.

Safety Cushion U-shaped safety padding for Uneven Bars, Horizontal Bar and Parallel Bars. With handle on the short side and Velcro for easy attachment. Length: 140 cm.

Trainer Support, 75 x 45 x 60 cm

Trainer Support, 100 x 75 x 75 cm

Methodical Block, 120 x 120 x 80 cm

Wall Bars Support The support is constructed for use with all types of wall bars. The complete wall bars support is foldable for easy storage. Set of rings with straps are not included.

Power Bench ”Stand-alone model”.The height of the power bench can easily be adjusted. The smooth running, upholstered sled that runs in bearings, is put in metal rails enabling extensive use without any problems.

Open Pit System for Horizontal Bar, Uneven Bar & Trampoline Ultimate.

Providing and fixing semi transparent polycarbonate compact sheet roofing of approved colour to make any normal shape of roofing / covering of any pitch and fixing with specially designed powder coated aluminium section with 60mm wide flange of standard design weighing not less than 1.1 kg/ m at spacing not more than 1.2 m centre to centre with EPDM gasket and silicon sealant on all four edges of aluminium section fixed with self drilling stainless steel screws all complete including aluminium edge angle 40 mm x 40 mm x3mm as per manufacture specification and as per direction of Engineer-in-Charge. 10 mm thick triple wall

a) Supply & Erection of Single stage/Horizontal pumps set with inbuilt prefilter,Thermoplastic injected pump casing. Impeller in noryl with Stainless steel shaft, mechanical seal in stainless steel connected to TEFC induction motor with built-in thermal protection and automatic reset suitable for 190/ 380 volts, 12.5 HP, 3 phase, 50 cycles A.C supply, IP-55 motor protection complete with inbuilt Filter basket in injected plastic material.Flow 175 m3/hr. @ 12-14 Mtrs. Head (Working 4 Nos. , Standby : 1 No.)

b) 250 mm dia. UPVC Suction valve ( Butterfly ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers.

b) 200 mm dia. UPVC Delivery valve ( Butterfly ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers.

b) 200 mm dia. UPVC Delivery Non Return valve ( Wafer Type ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers.

Filter (Horizontal Type) -Totally Anticorrosive Pressure Sand Filter 2000 mm dia. x 2500 mm Long, Manufactured with fiber glass & polyster resin, fitted with collector arms & diffuser made from unplastisized PVC & polypropelene, capable of accomodating a flow rate of 175 cum / Hour @ 40 cum / Hour / Sqm., 1.20 mtr. Bed Depth, complete with lid in polyester resin & fiber glass, manual air purge, cap for sand discharge & PVC flanged connection for inlet & outlet.

Filtermedia & underbed - a) Sillica sand media for filter with granulometry between o.4 & 0.8mm

Filtermedia & underbed - b) Gravel for filter with granulometry between 1-2mm

Automatic Valve Battery for Filter - Automatic Motorised driven 5-Valve batteries built entirely in UPVC with flange connections to filters according to DIN standards. Butterfly valves also in PVC supports made of zinc coated steel pipe with antivibration clamps & fixing plugs, Conn. 200 mm Dia.

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. a) 400 mm Dia. X 6 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. a) 350 mm Dia. X 6 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. b) 315 mm Dia. X 6 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. c) 250 mm Dia. X 10 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. d) 200 mm Dia. X 10 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. e) 160 mm Dia. X 10 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. f) 110 mm Dia. X 10 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. g) 90 mm Dia. X 10 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. h) 75 mm Dia. X 10 Kg/cm2

CIRCULATION PIPING Supply, Install, Testing & commissioning uPVC Piping including necessary fitting such as Elbows, Bends, Sockets, Tees, Collars, Nipples, Reducers, Stub Ends, diminishing pieces, Solvent Cement, etc. for Swimming Pool Inlet & Drain & Suction piping, Swimming Pool filtration plant piping, drain pipe along the pipe periphery including all fittings, fixtures and Ceiling/ Wall Support System suitable for following uPVC pipe as specified and directed. i) 63 mm Dia. X 10 Kg/cm2

Isolation Valves - (Pool Inlets ) a) 200 mm dia. UPVC Inlet valve ( Butterfly ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers.

Drain Valves - (Pool Drains) a) 200 mm dia. UPVC Pool Drain valve ( Butterfly ) with Valve mounting kit in PVC, Complete with PVC stud ends, PVC flanges, Nut bolts and washers.

Pool Basin Fittings a) ABS Plastic Concrete floor inlet with s.s. screw flow 12 m3/hr with 2" female and male connection.

Pool Basin Fittings b) VGBA Approved Drain grating in ABS Plastic , Frame in injected moulded plastic, Size of Grill - 450mmx450mm

Pool Basin Fittings c) SS-316 Plate type hair strainer for gutter connecting S. Pool Overflow Gutter to Balancing tank.

Pool Basin Fittings d) S.S.316 Ladder (4 Step) SS ladder with polished stainless steel hollow pipe of 43mm Dia. and of 14 gauge(1.6mm) thick, Anti-slip stainless steel steps with anchoring fixtures.

Pool Basin Fittings d) S.S.316 Ladder (5 Step) SS ladder with polished stainless steel hollow pipe of 43mm Dia. and of 14 gauge(1.6mm) thick, Anti-slip stainless steel steps with anchoring fixtures.

Pool Basin Fittings e) Overflow Grating 495 mm wide, 34/35 mm Thick, Made with uv stabilised Polyproplene.

a) Robotic Cleaner suitable for 50 m long pool, comply with the international certification of water proof rating for electronic products. The main unit should have Water 'Ingress Protection' (IP) rating of 68. Remote Control have IP21 and for Power Supply have rating of IP23.

b)Trolley mounted Plastic self priming pump with Inbuilt Prefilter and Catrdidge Filter set 3 HP, 3 Phase 415 V directly coupled with motor on suitable Stainless Steel frame work provision of small switch board comprising of ICTPN 32 Amps, DOL starter of suitable capacity and control wiring with copper cable.

c) Metallic vacuum head in Anodised Aluminium, 800 mm Long, connection external 2” to fit hoses, fork in Stainless Steel. for connection.

d) Extensible handles for cleaning attachments in anodized aluminium which can be adapted to the entire range of cleaning equipment, brushes, leaf skimmers and scoops, 9 feet to 27 feet. Long.

e) Transparent plastic vacuum hose 2” dia 30 mtrs. long including hose cuffs for connection to suction inlets.

f) Deep bag net made in polypropylene and white polyester netting butterfly nut connection.

g) Curved brushes made in polypropylene for pool basis and scum liners.

h) Algae brushes with stainless steel bristles.

Pool Water Testing Instrument Test kit suitable for measurement of residual Chlorine and pH

Chlorine & PH Dosing Equipments Liquid Chlorine dosing equipment - Chlorine solution preparation tank (200 lit. Complete with Agitator, water inlet, drain & overflow piping ( all 25mm ) all necessary valves ( 3 nos. ) & accessories dosing piping / tubing from tank to the dosing point with necessary valves & fittings and 2 Nos. dosing pump of Cap. 10 LPH.

Automatic pH Correction system comprise of an automatic proportional dosing system combining controller, electrical box and hydraulic by-pass probe holder in a single ready-to install unit. IP65 enclosures protect against water jets, Should Include two washable cartridge filters. 200 ltrs. Capacity PVC tank and PVC stirrer.

a) Stainless Steel Underwater led Light with S.S. 316L Housing, 40 w, 12 v Supply, Cool White Color, Niche in ABS Plastic, White color, with 2 m long cable, Plastic Conduit Hose,Junction Box in ABS Plastic with 3 entries of 3/4"

b) Electrical Cabling for Underwater Lights of ‘Polycab/Finolex 'Make Copper Flexible cable enclosed in PVC Conduit., 4.50 Sq. mm x 3 Core • Cable quantities are to be measured actually at site and paid as per unit rate.

Air/Water Heat /Chill Pump. The unit features with a highly efficient scroll compressor hermetically sealed, titanium heat exchanger, tube in fins heat exchanger extra large for greater efficiency with corrosion resistant coat. Outer casing made up of stainless steel powder coated. Equipped with advanced main controller and smart LCD wire controller.Refrigerent 407 c. Heating Input: 46.3 kw & output: 210 Kw. Ambient Temperature: 12 deg C, Desired Temperature: 28 deg C.

Geobubble Pool Cover 500 Micron with Unique patented design of two bubbles joined together by a structural waistline centre section, No sharp corners that could resist in thin or weak points in the design, No stress points due to the bubble’s smooth interconnected curves 50% thicker than a traditional bubble material at its thinner point Increased resilience against UV rays and chemical attack, Complete with suitable Automatic Roller.

Headwall /Endwall platform for Podium, those platform suitable for Swimming Pool with water recirculation in four sides. It is composed of an AISI 304 stainless steel frame and plastic grating, Grating should be made of polypropylene composite to resist UV rays and chemical products present in the water, the grating should have free space of over 45% to facilitate water recirculation, platform can be used as Turning panel and iy should include Anchors for Mounting and for Starting Blocks, Width - 2.5 m.

Starting Blocks with mounting frames and foundation bolts - The starting block is manufactured using AISI-316L painted with epoxy resins or polished and dip of plate size 500 x 700 mm. hight density polyethylene with no-slip machining Top platform, adjustablem Angle of diving platform surface max 10°. Double handle horizontal and vertical for backstroke start. The starting block is provided to numbers standard in 4 sides. Made in according with FINA regulation in force.

Float lane - 150 mm Dia. anti wave breaker lane ropes made made in polyethylene with anti-acid and anti UVA treatments with special feature for eliminate wave movement. Complete with spring tensioner all in stainless steel 316L and cover in silicon, in according with EN 13451-5 and FINA regulation in force. Suitable for high level competitions including SS 316L float line fixing post anchored on the deck.

S.S. Float Lane Storage designed to transport and store the Float Line after use in the swimming pool. Easy to use and aesthetically discreet. The float line roller is manufactured using AISI-304 Stainless Steel and includes a PVC bag for collecting excess water from the float lines. bag's lower outlets, it is emptied in a controlled manner with no water spillage. The cart has four rotating wheels for maximum mobility. Two of these have a brake. Suitable for Storage of 1 No. of 50 m Long 150 mm Dia. Float lane.

FALSE START INDICATOR POST- comprising of 2 nos. stainless steel 316L posts each of 48 mm dia and 1.8 m height provided on either side of the racing pool properly anchored in a suitable anchoring socket on the deck at specified location including one post provided with pulley and quick cord fixing and loosening device and including false start line comprising of polyester cord and a float. as per FINA.

d) BACK STROKE TURN INDICATOR POST - comprising of 2 no stainless steel SS 316L posts each of 48 mm dia and 1.8 m height provided on either side of the racing pool properly anchored in a suitable anchoring socket on the deck at specified location and shall span across the sides including set of flags as per specifications as per FINA.

Water Polo Goal Post, The water polo goal post should be lightweight, floating and very resistant. It is built entirely from aluminium and is ovenpainted white. Manufacturing and measurements in accordance with FINA international swimming federation standards, Floating: Polyurethane foam-filled aluminium floats, Goal frame: aluminium tube, Net fastening: stainless steel round rod, Net side pipe: stainless steel round pipe with fastening in frame and float, Fastening for goal lines, Nets included. Made in according with FINA regulation in force.

SPRING BOARD - Maxiflex Model B Part # 66-231-330 The 16' Maxi-B is basically a one piece ribbed extrusion of aluminum alloy 6070-T6, heat treated for a yield strength of 50,000 psi. It has a torsion-box extrusion, a two piece anchor angle, and tip end cap riveted to the basic section. It is tapered from the fulcrum area to the diving tip, and it is tapered from the fulcrum area to the anchor end. The board is coated in aqua-colored thermal-cured epoxy resin. The top surface is finished with a laminate of flint silica and alumina, between coats of epoxy, to effect a slip-resistant surface. epoxy adhesive.

Short Stand with No Handrails - Part # 70-231-524 ,The Diving Stand Anchor and Fulcrum Assembly, Catalog #70-231-520, "Short Stand" is designed for mounting on a concrete, steel, or other field-fabricated diving platform. The diving stand consists of heavy aluminum castings coated with epoxy paint. The roller and tracks are heat treated, hard-anodized extruded aluminum.

Air Cushioing System for Diving Pool comprising of an air compressor providing the source of compressed air. An air receiver providing a pressure buffer minimizing pressure fluctuations and different pressure loadings on the air compressor.Aftercooler providing cooled air supply to the air filters and assisting with air filtration. Air filters providing clean air to a second air receiver. The second air receiver providing capacity of the compressed air for the air fed systems. Assembly of various valves controlling the air and water fed systems. Two electrical control panels and two hand held units controlling the systems. Booster pumps for water spray jets.Pipeworks, fittings and water spray jets.

LIFE BUOY Made of Red & White color plastic, Dia. 24" complete with SS life belt holder and Post.

LIFE SAVING LOOP Made of stainless steel AISI –316L can be connected to telescopic handle by using butterfly nuts, complete with 5 m long telescopic pole.

Lifeguard Chair, 2155 mm High Made in 43 mm diameter, AISI-304 stainless steel. With demountable base plate. Includes treads, platform, and chair with parasol holder.

Providing and laying pu waterproofing treatment using Mariseal- 275 or equivalent Membrane waterproofing system for Swimming pool, Paddling Pool and Drainchannel Horizontal & Vertical surface or wherever required as per approved chemicals, methodology, manufacturer specifications & instructions of Engineer-in-charge. Work to include all labour and material, equipments, leveling, cleaning the base surface, roughening / hacking, chipping off unwanted material/mortar & all necessary grouting wherever required, curing, all lead & lift at all level, testing for water tightness, making good if necessary etc complete. Quoted rate shall include providing and making waterproofing treatment for all core cuts, under water lights as per the approved methodology directed by Engineer in charge.

Providing and laying Porcelain Swimming Pool Tile of size 245 mm x 120 mm and thickness 7 mm conforming to FINA (Federation International De Nation) Standard on horizontal and Vertical surface (Floor and Side Walls) in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like Light Blue laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 3-4 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and laying Petit Carre Porcelain Swimming Pool Tile of size 245 mm x 120 mm and thickness 7 mm conforming to FINA (Federation International De Nation) Standard on Vertical surface of Turning Walls in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like Light Blue laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 3-4 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and laying Porcelain Swimming Pool Tile of size 245 mm x 120 mm and thickness 7 mm conforming to FINA (Federation International De Nation) Standard for Lane Marking on horizontal and Vertical surface (Floor and Side Walls) in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like Cobalt Blue laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 3-4 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and laying Petit Carre Porcelain Swimming Pool Tile of size 245 mm x 120 mm and thickness 7 mm conforming to FINA (Federation International De Nation) Standard for Lane Marking on Vertical surface of Turning Walls in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like Cobalt Blue laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 3-4 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and laying Petit Carre Porcelain Finger Grip Tile with Safety Marking of siz 245 mm x 120 mm and thickness 18 mm conforming to FINA (Federation International De Nation) Standard on Horizontal surface (Coping) in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like Cobalt etc. laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 3-4 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and laying Porcelain Petit Carre Antislip Tile with of size 245 mm x 120 mm and thickness 6.8 mm conforming to FINA (Federation International De Nation) Standard on Horizontal surface (Coping) in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like unglazed etc. laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 2-3 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and laying Porcelain Petit Carre Bevelled Edge Antislip Tile with of size 245 mm x 120 mm and thickness 6.8 mm conforming to FINA (Federation International De Nation) Standard on Horizontal surface of Rest Ledge in swimming pool of approved manufacturer and of shade approved by architect or engineer in charge like unglazed etc. laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 2-3 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing, fixing, testing and commissioning of I-25, Pop-up ROTOR sprinkler. The sprinkler shall be of the gear-driven, rotary type, capable of covering a 11.9-21.6 meter radius at 3.5 bars with a discharge rate of 13.6 to 120.7 l/min. The sprinkler shall be both full-circle and adjustable part-circle operation in a single unit. The sprinkler shall be minutely adjustable from 50° to 360°. It shall be adjustable in all phases of installation (i.e., before installation, after installation while static, and after installation while in operation). The sprinkler shall be equipped with a self-adjusting stator to ensure constant rotation speed regardless of nozzle installed. The sprinkler shall have a non-strippable drive mechanism that allows the nozzle turret to be turned during operation, without damage. It shall also have an automatic arc return feature that returns the nozzle turret to its proper orientation if it is turned outside its intended arc of coverage.

Providing, fixing, testing and commissioning of PGP ULTRA, Pop-up ROTOR sprinkler . The sprinkler shall be of the gear-driven, rotary type, capable of covering a 4.9m -14.0 m meter radius at 2.5 bars with a discharge rate of 0.02- 0.891Lps. The sprinkler shall be both full-circle and adjustable part-circle operation in a single unit. The sprinkler shall be minutely adjustable from 50° to 360°. It shall be adjustable in all phases of installation (i.e., before installation, after installation while static, and after installation while in operation). The sprinkler shall be equipped with a self-adjusting stator to ensure constant rotation speed regardless of nozzle installed. The sprinkler shall have a non-strippable drive mechanism that allows the nozzle turret to be turned during operation, without damage. It shall also have an automatic arc return feature that returns the nozzle turret to its proper orientation if it is turned outside its intended arc of coverage. The sprinkler shall be equipped with a drain check valve to prevent low head drainage, and be capable of checking up to 10 feet (3.0 meters) in elevation change. The rubber cover shall be surrounded by a protective rubber boot when sprinkler is in the retracted position. The body and riser of the sprinkler shall be constructed of corrosion resistant, impact resistant, heavy-duty A.B.S. The sprinkler shall carry a five-year, exchange warranty. Including swing joint, service saddle and other fittings as per direction of engineer-in-charge.\

Providing, fixing, testing and commissioning of PROS04 Pop up spray head bodies with ADJUSTABLE nozzle capable of covering 1.2M -5.2m at 1.0 - 2.1 Bars, pressure, The adjustable arc nozzle shall be adjustable from 0 to 360 degree. The body of the sprinkler shall be constructed of corrosion and UV-resistant, heavy-duty A.B.S. The riser of the sprinkler shall be constructed of abrasion and UV-resistant A.B.S. and shall be adjustable for pattern alignment. The riser shall be compatible with female threaded nozzles and shall have a stainless steel spring for positive retraction when irrigation is complete. The sprinkler shall have a pressure-activated, multi-function, UV stable wiper seal that will clean debris from the pop-up stem while it retracts. The seal shall be molded around a rigid plastic ring to prevent seal deformation. This seal shall prevent the sprinkler from sticking in the up position and be capable of sealing the sprinkler riser stem to the sprinkler cap under normal operating pressures.

Providing, Fixing, Testing & Commissioning of 16mm Drip Tubing of approved make including fittings, all labours, taxes & duties etc all complete as per direction of engineer-in-charge.

Providing, Fixing, Testing & Commissioning of pressure compensating dripper of 4 lph of approved make including fittings, all labours, taxes & duties all complete as per direction of engineer-in-charge.

Providing, fixing, testing and commissioning of Isolation Valve in mainline for bypass and flow diversion of approved quality. 80mm to 100mm

Providing, fixing, testing and commissioning of a double acting 2" Air release valve, The Air release valve shall be capable of both releasing and admitting air from and into the line. The working pressure shall be 5 bar. Including service saddle and riser assembly.

Providing, fixing, testing and commissioning of a double acting 1" Air release valve, The Air release valve shall be capable of both releasing and admitting air from and into the line. The working pressure shall be 5 bar. Including service saddle and riser assembly.

Providing, fixing, testing and commissioning of 12" Rectangular Valve Box with green lid and corrugated structure with unique shovel access slot and bolt hole knockout.

Providing, fixing, testing and commissioning of 6"Round box with green lid and corrugated structure with unique shovel access slot and bolt hole knockout.

Providing, fixing, testing and commissioning of Brass Key threads into top of QCV to provide water access And Brass Swivel Elbow.

Providing, fixing, testing and commissioning of Sand Filter with capacity matching pump design flow having an suitable inlet and outlet connections.

Providing, fixing, testing and commissioning of Disc Filter with capacity matching pump design flow having an suitable inlet connections , to create a helical effect in the incoming water ,spinning particulate in suspension away from the filtering element and so minimizing cleanings frequency ,3/4" outlet for flushing at bottom of filter & maximum working pressure of 10 Bars. with pressure gauge.

Operational &amp; Maintenance for three years: Part 1 - Complete maintenance for three year of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, hedge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants (if damaged), gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter , removal of garden waste, applying insecticide, pesticide &amp; fertilizers(whenever required) top dressing of lawn with good earth and menure and maintenance of other garden related works as directed by office-in-charge (including Cost of Good Earth, Manure, Fertilizer, Insecticide , Pesticide , lawn mover and brush cutter &amp; other T &amp; P material/articles). Part 2 - Maintenance and Cleaning of Water tank and water bodies Maintenance and Cleaning of Water tank, and water bodies including disinfection once in three month for three year period all complete as per direction of engineer in charge.

Providing, fixing, testing and commissioning of Gun Metal/Brass Gate Valve 3/4" of approved make as per specification and direction of Engineer In Charge etc. Complete. Make- Zoloto

Providing, fixing of 10"Round box with green lid and corrugated structure with unique shovel access slot and bolt hole knockout as per specification and direction of Engineer In Charge etc. Complete. Make- Rain-Bird

Providing, fixing, Testing & commossioning of Self Cleaning Automatic Screen Filter 50m3 / Hr - Working on Pressure Differential self cleaning mechnism, having minimum screen surface area of 1600cm2 as per specification and direction of Engineer In Charge etc. Complete. Make- Amiad

Providing, fixing & commissioing of 2" Solenoid Valve - BSP Female Threaded, Pressure - 1 to 10 Bar Make: Rain-Bird as per specification and direction of Engineer In Charge etc. Complete.

Providing, fixing & commissioing of 1-1/2" Solenoid Valve - BSP Female Threaded, Pressure - 1 to 10 Bar Make: Rain-Bird as per specification and direction of Engineer In Charge etc. Complete.

Providing, fixing & commissioning of Pressure Reducing Valve 2" Providing , supplying and installation at site Pressure Regulating dial ( 0 to 5 Bar) . • Regulates and maintains constant outlet pressure between 15 and 100 psi (1,04 to 6,90 bar) within ±3 psi (±0,21 bar) • Adjustment knob with detents permits finetune setting in 1⁄3 psi (0,02 bar) increments • Improved spike reduction capabilities reduce water hammer • Ergonomic design with snap-tight cover to prevent vandalism • Waterproof dial cartridge eliminates fogging and binding • Dial cartridge retrofits into all existing PRS-B units • Schrader valve connects pressure hose gauge • Easy field installation. PRS-Dial threads underneath the solenoid and adapter (Rainbird/ Toro/ Orbit) etc. as per specification and direction of Engineer In Charge etc. Complete. Make: Rain Bird

Providing, fixing & commissioning of MSP-1 Maxi Surge Pipe to Protect central control components from electrical surges on a two-wire communication path as per specification and direction of Engineer In Charge etc. Complete. Make- Rain-Bird

Providing, fixing & commissioning of Flow Sensor 3", Rainbird - Accuracy: +- 1% (full scale), 7.13" x 3" (diameter) (181mm x 76mm (diameter) Velocity: 1/2-30 feet (0.15 - 9.2 meters) as per specification and direction of Engineer In Charge etc. Complete.

Providing, fixing & commissioning of Water proof Sensor Decoder to connect Flow Sensor to Controller as per specification and direction of Engineer In Charge etc. Complete. Make- Rain-Bird

Providing, fixing & commissioning of Rain Sensor - Multiple rainfall settings from 1/8" to 3/4" (5-20 mm) are quick and easy with just the twist of a dial.UL, cUL listed; CE, C-Tick approved. Electrical rating suitable for use with up to ten 24VAC, 7VA solenoid valves per station, plus one master valve as per specification and direction of Engineer In Charge etc. Complete. Make- Rain-Bird

Providing, fixing & commissioning of Master Solenoid Valve cum Water Meter 3 Hydrometer with Solenoid Controll integrates a vertical turbine Woltman-type water meter with a diaphragm actuated hydraulic control valve. Impeller drive magnetically coupled to a vacuum-sealed meter register in the control head. As the system’s Flow Meter and Main Valve, it controls system irrigation together with the irrigation controller as per specification and direction of Engineer In Charge etc. Complete. Make- Bermad

Providing, fixing & commissioning of Weather Proof Cable Connection DBY Make : 3M / Rain Bird,with Electrical Spring Connector and a high impact, UV-resistant polypropylene tube prefilled with moisture-resistant gel as per specification and direction of Engineer In Charge etc. Complete.

Providing,fixing & commissionning of Voltage Stabilizer 0.5 KVA as per specification and direction of Engineer in Charge etc. Complete

Providing, fixing & commissioning of PVC Pipe 32mm Cable Conduit as per specification and direction of Engineer In Charge etc. Complete. Make- Supreme

Supply & nstallation of 16 sqmm x 4 core armoured copper cable for Hydropneumatic pumps

Supplying, fixing testing and commissioning of Y-stainer(Zoloto make) with ISI conductor cable of 1.1 KV grade as required.

Providing and Supplying of following dewatering pumset 1HP set head range-6-12 meter.Discharge-336 to LPM.Maximum soil size 20mm, phase, duty tested from certified agencies inclusive of all materials ,central stase and municipal taxes and duties in spection charge,transit,insurance,loading and unloading 7 stacking etc.Complete as per direction of Engineer in charge

Inbuilt of drain cover slab in providing perforated holes using PVC pipe 50 mm dia. including cost of allmaterials and labour involved with all leads and lifts etc. as per drawing and direction of Engineer in Charge.

Structural steel hot dip galvinized MS angle welded over a base plate including cutting, welding ,hoisting and fixing in position with 3 nos. of 12mm diameter fastnerrs etc. complete as per drawings and direction of Engineer complete etc.

Supplying and stacking of suitable, approved Vermicompost collected from approved source; for horticulture and landscaping work including loading, unloading and carriage all lead and lift as per direction of Engineer in Charge. ( Payment of the work shall be made only after spreading / utilization of the same)

Construction of RCC valve chamber internal size 1.2m x 1.0m x 1.3m, 100mm thick PCC- M10 and RCC M20 grade 150mm thick wall, precast RCC M35 grade cover 125mm thick on top for protection of valve coming under traffic & extended MS valve operating spindle rod as reqd etc. Including Excavation, back filling, steel reinforcementon, shuttering, labour charges etc as per drawing and as per direction of Engineer complete etc.

Provision for Ductile iron/M.S pipe inter connection of old to new pipe line with excavation of trench as per requirement of any diameter & type of pipe line in muddy area i/c dewetering the trench laying & jointing of pipe and specials, back filling the trench i/c testing of joints cost of labour & specials such as D-Joints couplers, flanged sockets,Tee solvent cement including all lead and lift upto 1.5m depth and pipe dia. upto 300mm, complete job work as per approved specification and as directed by Engineer in charge.

Providing, laying, Jointing & field testing of DWC HDPE Pipes (with external annular corrugation and smooth internal walls) duly tested Conforming to IS 16098 (PART-II): 2013 having stiffness class of SN 8 with ring stiffness not less than 8.00KN/SQM. and impact resistance TIR valve not more than 10% including necessary jointing materials for non-pressure underground sewerage, drainage & cross drainage application. Inclusive of all taxes related to central, state and municipal, inclusive of excise duty, inspection charges, transportation charges, transit insurance, loading/unloading and stacking at site/store etc. and as per Technical Specifications and as per direction of Engineer.This is also inclusive of Jointing material i.e Pipe with online/offline coupler and elastomeric sealing ring. All the joints shall be confirmed water tight as per standards. 300/345 mm dia

Providing, fixing, installation, testing and commissioning of Precast RCC M-40 grade Rectangular chamber with internal size 0.9X0.8m depth upto 1.0m. wall thick 150mm, bottom slab thick=150mm, FRP circular cover internal opening size 600mm dia. (Designed for 20tone loading capacity (heavy duty) etc.). 100mm thick bottom PCC 1:3:6, fixing of FRP frame and cover using M-20 grade concrete. with CM1:1 around pipe entering and leaving the chamber, providing and fixing of safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12mm dia. steel bar of approved make at every 0.30m height, including double jali steel reinforcement 10mm dia. bar vertical and horizontal both the direction 150mm c/c as per drawing, hydro testing of chamber, loading, unloading, conveyance & cost of labour, earth work in excavation, backfilling, dewatering etc. complete as per direction of Engineer-in-Charge.

Providing, fixing, installation, testing and commissioning of Precast RCC M-40 grade Rectangular chambers with internal size 1.2X0.9m depth upto 1.3m. wall thick 150mm, bottom slab thick=150mm, FRP circular cover internal opening size 600mm dia. (Designed for 20tone loading capacity (heavy duty) etc.). 100mm thick bottom PCC 1:3:6, fixing of FRP frame and cover using M-20 grade concrete. with CM1:1 around pipe entering and leaving the chamber, providing and fixing of safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12mm dia. steel bar of approved make at every 0.30m height, including double jali steel reinforcement 10mm dia. bar vertical and horizontal both the direction 150mm c/c as per drawing, hydro testing of chamber, loading, unloading, conveyance & cost of labour, earth work in excavation, backfilling, dewatering etc. complete as per direction of Engineer-in-Charge.

Providing, fixing, installation, testing and commissioning of Precast RCC M-40 grade Rectangular chambers with internal size 1.2X0.9m depth upto 1.6m. wall thick 150mm, bottom slab thick=150mm, FRP circular cover internal opening size 600mm dia. (Designed for 20tone loading capacity (heavy duty) etc.). 100mm thick bottom PCC 1:3:6, fixing of FRP frame and cover using M-20 grade concrete. with CM1:1 around pipe entering and leaving the chamber, providing and fixing of safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12mm dia. steel bar of approved make at every 0.30m height, including double jali steel reinforcement 10mm dia. bar vertical and horizontal both the direction 150mm c/c as per drawing, hydro testing of chamber, loading, unloading, conveyance & cost of labour, earth work in excavation, backfilling, dewatering etc. complete as per direction of Engineer-in-Charge.

Providing, fixing, installation, testing and commissioning of Precast RCC M-40 grade Rectangular chambers with internal size 1.2X0.9 m depth upto 1.9m.wall thick 150mm, bottom slab thick=150mm, FRP circular cover internal opening size 600mm dia. (Designed for 20tone loading capacity (heavy duty) etc.). 100mm thick bottom PCC 1:3:6, fixing of FRP frame and cover using M-20 grade concrete. with CM1:1 around pipe entering and leaving the chamber, providing and fixing of safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12mm dia. steel bar of approved make at every 0.30m height, including double jali steel reinforcement 10mm dia. bar vertical and horizontal both the direction 150mm c/c as per drawing, hydro testing of chamber, loading, unloading, conveyance & cost of labour, earth work in excavation, backfilling, dewatering etc. complete as per direction of Engineer-in-Charge.

Providing, fixing, installation, testing and commissioning of Precast RCC M-40 grade Rectangular chambers with internal size 1.2X0.9 m depth upto 2.2m. wall thick 150mm, bottom slab thick=150mm, FRP circular cover internal opening size 600mm dia. (Designed for 20tone loading capacity (heavy duty) etc.). 100mm thick bottom PCC 1:3:6, fixing of FRP frame and cover using M-20 grade concrete. with CM1:1 around pipe entering and leaving the chamber, providing and fixing of safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12mm dia. steel bar of approved make at every 0.30m height, including double jali steel reinforcement 10mm dia. bar vertical and horizontal both the direction 150mm c/c as per drawing, hydro testing of chamber, loading, unloading, conveyance & cost of labour, earth work in excavation, backfilling, dewatering etc. complete as per direction of Engineer-in-Charge.

Supplying erection testing and commissioning of Low intensity LED type aviation obstruction luminaires to be mounted on high masts.

Providing,laying and Fixing 10 to 12mm thick Antiskid external flooring tiles of approved size 600x600mm and above conforming to IS specification of approved make, colour, shade laid on 20 mm thick Cement Mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement mixed with matching pigment etc., complete with proper adhesive to paste on the surface, as per direction of Engineer Incharge

Supplying and laying HDPE pipe of 4kg/cum in ground below road, path etc at a depth not less than 40 cm and upto 90 cm including excavation, dismantling of road if required and refilling the trench with excavated material, ramming and making the surface good etc. as per specification, complete as per Engineer-in-Charge. 40 mm Outer dia.

SITC of,4 MP Network Motorized ANPR Camera

SITC of,2 MP Network PTZ Camera -25X, 150 mtr

SITC of,KEYBOARD (JOYSTICK ATTACHED)

SITC of,64 Channel Network Video Recorder - 4 Sata Port, 320 mbps , Support ANPR Camera

3 Core 1.5MM Copper Armoured Cable with laying

SITC of,2 KVA Interactive UPS, 4 hours back up

SITC of , Automatic Boom Barrier Gate for up to 6 Meter

SITC of , Cable & Connection of Loop Detector & Loop Controller with Boom Barrier and Card Dispenser / Collector

Providing and laying R-11 Rated Porcelain Anti slip Tile with of size 300 mm x 300 mm and thickness 10 mm conforming to FINA (Federation International De Nation) Standard on Horizontal surface (Pool Deck ) on swimming pool Surrounding Deck of approved manufacturer and of specified shade like Beige/ Cotto/ Yellow/ Grey etc. laid in approved pattern on 3- 6 mm ( 5 mm average) thick bed of adhesive mortar of Polymer modified cementitious adhesive ( Bal Endura gold star / latecrete / Rock force ) in conjuction with polymer modified liquid Bal Endura admix Adlor equivalent product of latercrete / Rock force mixed in required porportion as specified by manufacturer including filling / scaling of joints 2-3 mm thick between the tiles with epoxy grout of Bal Endura Epoxy grout / Latecrete / Rock force with matchingcolour pigment to make it water tight and finished neat complete as per direction of Engineer-in-Charge.

Providing and fixing HT Danger Notice Plate of 250 mm x 200 mm 2mm thick, made of mild steel and vitreous enamelled white on both sides and inscription in signal red colour on front side as per IS:2551 with accessories, hardwares etc as per direction of engineer, CSPDCL standards and Electrical inspectorate standards.

Providing and fixing following rating and breaking capacity MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as per specification, IS/ IEC: 60947-2 and Ics = 100 % Icu.63A-40A 4pole MCCB as Incomer;

supply , installation , testing and commssioning of Lighting protection radius 107 Mts . LPI/ABB / equivalent Make advanced technology ,lighting protection Early streamer Emission ( ESE ) lighting conductor air termination complete with all accessories etc as required and as per engineer incharge

Supply , installation , testing and commssioning of GI. Mast for mounting the terminal & adaptor with ESE Air Terminal & various accessories( fasner , guy wire , ring fasner, huk etc)  Length – 5mtr  Pipe – Jindal , Dia. -50mm  Thickness – 3.4mm  Base plate – (300x300x6)mm

Supply , installation , testing and commssioning of Maintenance free earth set consisting of copper bonded rod 17.2mm dia 10 ft long with welded clamp, 25kg earth enhancing chemical compound, Poly Plastic Cover complete with all accessories etc as required and as per engineer incharge

Supply , installation , testing and commssioningof Lightning Strike Recorder - 6 digits display to record the lightning current in an IP 67 enclosure with the minimum sensitivity of 3KA & maximum capacity of 150 KA (8/20 micro second waveform)

Supply , installation , testing and commssioningof Test Link Joint in an IP 55 weather proof polyplastic enclosure of suitable dimension.

Supply , installation , testing and commssioning of 70sqmm pure copper single core wire

Providing and preparing sub-grade including removal of existing topsoil, regrading and fine dressing to required sub-grade levels and profile to form the specified crown of the field, ensuring a stable, well-compacted, and rock-free surface. The work includes picking and removal of stones and deleterious materials exceeding 75 mm size, proof rolling with mechanical roller, identification and rectification of soft spots by excavation and replacement with suitable approved fill material, and compaction to achieve a firm formation with minimum CBR of 5% as directed by the Engineer-in-Charge/Consultant. Further includes final rolling with light roller in dead-weight mode to achieve required finish and levels.

Providing and laying complete sub-surface drainage system including setting out of drain lines, excavation of trenches by mechanical trencher at sub-base level to required depth (approx. 300 mm) and width (200 mm), dressing, cleaning and compacting the trench bottom with vibro hand compactor, and disposal of surplus excavated material outside site. Providing, laying and spreading 6–10 mm graded aggregate (100 mm thick) at the base of drain, supplying and laying 110 mm dia corrugated perforated PVC pipes with geo febric socks , complete with all fittings such as end caps, Y-joints, connectors/sleeves, etc., including jointing, fixing, and alignment. Backfilling the trench with specified aggregate up to sub-surface level and connecting the system to peripheral drains as per approved drawings and directions of Engineer-in-Charge.

Supplying, deliver , stacking on site Poyta Sandy loam Soil as per directions and free from stone rubbish. The soil should be fresh from quarry, including loading, unloading, royalty etc. Complete as directed by engineer in charge.

ROOTZONE: Supply & Spreading of Sand: Supply & Sprading of sand at 125mm thick over the entire sub base. Sand suitable for a root zone should be a medium to coarse (0.15- 1.0 mm) particle size and should have sub-angular or sub- rounded shape. (NOTE:Coarse sand:60% of the material must fall in the .05 to 1 mm range. Medium Sand:.5 to.25mm & Fine Sand .25 to .15 mm not more than 20%.Very find Sand.15 to .05 mm Maximum permissable is 10% , Silt and Clay <0.05No more than 5% silt and clay.)

ORGANIC MATTER FOR ROOTZONE:Supply and uniformly spread 6kg/sqm of organic fertiliser with micro-organisms , macro and micro nutrients , with every square meter. Thereafter mix the organic matter with the top 50mm of the spread sand by rotivator. To have a uniform rootzone mix.Provide for 3 applications.

FINISHING LEVELS Once the rootzone is spread over the sub base rectify andulations if any , level and compact with water,to keep the root zone moist uniformly.

SUPPLY AND APPLY: Diammonium Phosphate over the entire FOP before grassing at the rate of 25 gms per sqm .

SUPPLY AND PLANT Source, Supply, Deliver & Plant Bermuda 419 grass on site by Planting method directed by engineer in charge. The grass must be weed fee. Rate including all required fertilizer, pesticider & Chemical etc. complete for growing the turf.Spec. No.:- As directed by Engineer in charge

Providing, supplying, laying, fixing and commissioning of semi-automatic irrigation system including HDPE main and lateral pipelines (90 mm, 75 mm, 63 mm dia) with all fittings (butt fusion/compression), pop-up sprinklers with swing joints, clamp saddles, valves (quick coupling, ball valves, air release valves, etc.), filtration unit (disc filter with pressure gauges and accessories), automation system (solenoid valves, controller, cabling and connectors), pumping unit (10 HP pumps with control panel, valves and GI fittings), valve boxes, trenching and backfilling, and all allied accessories. Including installation, testing, commissioning, preparation of shop drawings, and making the system fully operational as per manufacturer specifications, site conditions and directions of Engineer-in-Charge. Providing necessary excavation for pipelines, proper alignment, levelling, jointing, anchoring and protection of system components. Including flushing, trial runs, pressure testing and adjustments to ensure uniform water distribution and desired sprinkler performance. Including all electrical connections, earthing, control wiring and integration of automation system for efficient operation. Including maintenance support during defect liability period to ensure satisfactory performance of the complete irrigation system.

construction of Cricket Pitch with all materials and labour . Area / Size of Pitch - 24.5 L x 3.05 W X 3 PITCH Materials use for Pitch a) 100 MM GSB . B) Brick bat 100 mm l. C) 150 mm sand filter media. d) 250 mm picth soil with Black cotton e)Cynodone dactylon

Football Goal Post (All As per FIFA Requirement for premier Tournament) Supply and installtion of Uprights & Crossbars made from 102mm x 112mm reinforced aluminium with double recess for flush fitting fixings. Reinforced welded aluminium corner joints for improved aesthetics and superior strength, with laser cut internal fixing for exceptionally accurate joints. Injection moulded toughened nylon net clips that won't deteriorate over time. Lock-in T-bar to allow for easy storage of the bottom net bar against upright for pitch maintenance. Reinforced net support system prevents bowing under intense tension. New, heavy duty ratchet winch and webbing strap allows for high-class net shape with the inclusion of a failsafe wire providing 100% security during matches. Lock-in bottom net bar 38mm diameter aluminium bar with ground secure key lock mechanism complete with 4 sockets and whitePolyester powder coated of size 7.32m x 2.44m Set = 2 Goals with 4 x 460mm deep sockets, and net etc. all complete as per FIFA Specification. MAke :- Freewill/ harrod/ shelde

Supply of Players dugout structure fabricated from MS tube having minimum dimension of 50 x 50 mm Square Tube detachable framework with matt finish. The height of the dugout will be 2.05 meter at front side, 0.4 Mtr Radius curved roof and 4.9mtr length The seating capacity will be of 10 players. The structure will be covered with 3mm thick transparent or colored polycarbonate sheet on top and two sides.The Structure is Provide with HDPE Blow Molded Seat FI1002 Double-wall hollow blow mold bucket type seat having minimum dimensions as 500 mm side length x 440 mm front width x 420 mm rear height in one piece of HDPE having minimum shell thickness of 3 mm on each wall. Minimum seat density of 0.95 gram/cm3, weight of plastic chair should not be less than 2.65 kg. Chair should withstand in high temperature not less than 50°C with ultraviolet stabilizer and color fastness, having ergonomic design, the chair should be fixed with Metal Inserts moulded inside seat to connect seat with Galvanized pipes 32mm OD tube and 2 mm thickness running under the chairs. The pipes are resting above the structure. Water should not accumulate on chair. Chair should have a warranty of 2 years against significant colour fading and 3 years against breakage due to manufacturing defects. Chair Plastic Part should have been tested with xenon –Arc exposure Test as per ISO 4892-2:2013, Cycle-1. The Grey Sale Rating should be (GSR): > 4, Delta Δ E: < 3 MAke :- Freewill/ harrod/ shelde

Supply & Installation of synthetic all weather acrylic material approved by International Tennis Federation (ITF) having Eight layers, 2 coat of Acrylic Resurface 5 coat of Rubber course 2 coats of texture course 1 coat of Color And 2 coat of White Stripping Paint for game line marking.

Supply and installation of an Aluminium Bleacher of 4.5 mtr wide with 5 rows for 41 persons. Cross support frame is made of aluminum Pipe framework of size 50 X 50mm Aluminim Deck Profile of 250mm x 38 mm height. Blow molded HDPE seat having dimension Width: 440mm,Back Height: 420mm, Depth:500mm. will be provided for seating. Material: Blow molded, HDPE (high-density polyethylene), Anti UV Protection.Railing at the back of the bleacher.

Providing & Fixing Pickleball Net Post System (International Standard) Providing and fixing pickleball net post system o comprising powder-coated MS/steel net posts with internal winding mechanism, complete with ground sleeves, anchor fasteners, and all necessary accessories. The system shall be suitable for pickleball court of 22’-0” width with net height 36” at sidelines, conforming to international standards. Posts shall be rigid, corrosion-resistant, and properly aligned, including installation as per manufacturer’s specifications and drawings, complete in all respects as directed by the Engineer-in-Charge..Make Freewill / SPORT TECH/ uphos

SYNTHETIC JOGGING TRACK: Supply & Applying all weather proof cushioned out door spike proof sports surface 2 layered, water permeable all-weather surface made of structural sprayed polyurethane two Coats on an in-situ polyurethane bonded rubber granulate Sub-base or equivalent product as per satisfaction of EIC. Thickness: 12 mm (10mm Base layer + 2mm EPDM Spray On Top), Colour : Red

Raising/lowering type lantern carriage designed to carry specified nos of luminaries

UOM Name

Percentage

% of Cost of Bridge (excluding Maintenance) sanctioned by competent authority

Per mile

1000 piece

Print

Per Diem Rate

MAN DAYS

1 Piece

1 Strip

PRINT