REPAIR MAINT TO EXTERNAL WATER SUPPLY PIPE LINE AND CONNECTED ITEMS AND EXTERNAL ELECT WORKS, PANELS AND OTHER MISC WORKS AT DBS AND ASCON NODES UNDER GE(N) BIKANER

Amount

(b)Ditto All as per Srl item No 01(a) here in above but size of cable 16 Sqmm 2 core

(d)Ditto All as per Srl item No 01(a) here in above but size of cable 25 Sqmm 4 core

(e)Ditto All as per Srl item No 01(a) here in above but size of cable 35 Sqmm 3.5 core

(f)Ditto All as per Srl item No01(a) here in above but size of cable 50 Sqmm 3.5 core

M&L Cable indoor / outdoor end terminals jointing kit for LV/LT 1100 V cable heat shrinkable type joint kit complete with jointing material and accessories, thimbles etc suitable for 25 Sqmm to 50 Sqmm 3.5 core XLPE armoured aluminium conductor cable including testing after jointing, fixing in replacement complete all as specified as directed by Engineer-in-Charge.

Taking out old LT underground cable and laying after removing of defects any type/size laid in trenches/through pipe in road crossings/ paths /drains /ducts /floors /along poles/walls/ceilings/ equipments etc including commissioning and testing complete all as specified and as directed by Engineer-in-Charge.

Supply and laying un-reinforce precast concrete cable cover, class LV type-1, size 250 mm X150 mm x 40 mm for protection of cable complete all as specified and as directed by Engineer-in-Charge.

M&L for Erreting Steel Tubular Swaged Pole Type 410-SP-31 (9.0 Metre long) including Cast Iron Base Plate, Finial Taper Plug, Cap, Mild Steel Bolts, Nuts, Screws including applying two coats of Black Bituminous Paint Internally and Externally from bottom End of Pole upto PCC Coping and applying with two coats of Aluminium Painting over a coat of red oxide Primer (Externally from Top of Coping)and applying Two Coats of Synthetic Enamel Painting in alternate Yellow & Black Strips Painting (4 No. Each Strip 300 mm wide) and also including numbering to poles with synthetic enamel paint on black base of size 15 cm x 10 cm and numbering in 8 cm height of number with white paint, including dismantling of old unserviceable one complete all as specified and as directed. Note : Earthwork, Cement Concrete, etc. will be measured and paid under approprite Items.

M&L for Erreting Pre-stressed concrete poles 9 meter long, 102mm x 172mm at top and 102 mm x 279 mm at bottom, class 10, complying with requirements of IS-1678, including painting with two coats of synthetic enamel paint (in alternate black & white/yellow strips of 30 cm height) upto 1.5 meter height from top of PCC coping and also including numbering to poles with synthetic enamel paint on black base of size 15 cm x 10 cm and numbering in 8 cm height of number with white paint, including dismantling of old unserviceable one complete all as specified and as directed by the Engineer-in-Charge.

M&L for Plain cement concrete (1:3:6) type C-1 using 20mm graded stone aggregates as in foundation for stay and copping of pole above ground level including finishing to exposed concrete surfaces even and fair and provision of form work for rough finished surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L for Plain cement concrete (1:4:8) type D-2 using 40mm graded stone aggregates as in foundation for pole complete all as specified and as directed by Engineer-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, laying of cables , pipes etc. nexc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil.

Excavating in trenches, n exc 1.5 m wide and exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. nexc 10 sq m on plan and exc 1.5 m in depth but not exc 3 m in depth and getting out in soft/loose soil.

Returning, filling in soft/loose soil including spreading, leveling, watering and well ramming, in layers not exc 25 cm complete all as specified and as directed by the Engineer-in-Charge.

Removing of surplus soil to a distance not exc. 50 meter and depositing where directed at a level not exc.1.5 metre above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Local tibba dry sand cushioning and cover (8 cm thick layer of sand before laying of cable and 15 cm thick layer of sand after laying of cable) for protection of cable, material and labour complete all as specified and as directed by Engineer-in-Charge.

fixing Only in replacement GI pipe light grade 40 mm bore (ISI marked) laid in trenches/ road crossings/ fixed to poles/ceiling / along walls/ path /drain/floors with and including all necessary clamps, nuts, bolts, washers etc and all fittings as required, complete all as specified and as directed by the Engineer-in-Charge. (Note :- Necessary excavation, earth work and same work shall be measured and paid for separately.)

Ditto All as per Srl item No 14 here in above but dia of pipe 50 mm

Boring of holes under road 110 mm dia, pavement, hard standing by trench less technology(manually) with out disturbing the top surface of roads for laying of cables/GI pipes complete all as specified and as directed by the Engineer-in-Charge.

fixing only in replacement MCCB,63 Amps, 4 pole, 415 Volts, including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Fixing only in replacement MCCB, 100 Amps, 4 pole, 415 Volts, including thimbles, nuts, bolts, washers etc. making including incoming and outgoing connection complete all as specified.

Ditto All as per Srl item No 18 here in above but 160 Amps

Ditto All as per Srl item No 18 here in above but 200 Amps

Ditto All as per Srl item No 18 here in above but 400 Amps

M & L preparing old painted surfaces by scraping and removing old paints, rust, etc. from Steel Tubular Poles (above the Planting Depth and PCC Copings) and Mild Steel Cross Arms, Cable Protection Pipe, Brackets, etc. and applying one Coat of Red Oxide Zinc Chrome Primer, alternate Yellow & Black Strips Painting (5 No. Each Strip 300 mm wide) and remaining portion of Pole also including numbering to poles with synthetic enamel paint on black base of size 15 cm x 10 cm and numbering in 8 cm height of number with white paint and Cross Arms, Cable Protection Pipe, Brackets, etc. treated with Two Coats of Aluminium Paint complete all as specified and as directed.

M & L preparing old painted surfaces by scraping and removing old paints, rust, etc. from Pre-stressed Concrete Pole (above the Planting Depth and PCC Copings) and Mild Steel Cross Arms, Cable Protection Pipe, Brackets, etc. and applying Two Coats of Synthetic Enamel Painting in alternate Yellow & Black Strips Painting (5 No. Each Strip 300 mm wide) and remaining portion of Pole treated with Two Coats of Exterior Weather Proof Paint also including numbering to poles with synthetic enamel paint on black base of size 15 cm x 10 cm and numbering in 8 cm height of number with white paint and Mild Steel Cross Arms, Cable Protection Pipe, Brackets, etc. treated with Two Coats of Aluminium Paint complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m below normal ground level) with top edge of the plate at a depth not less than 1.5 m below ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15 cm on all sides, connected to galvanized earth iron strip 32 x 6 mm with and including nuts, bolts, check nuts & washers of galvanized iron or steel and riveted to earth plate at one end and connecting to main switch board or metallic bodies of HT/LT equipments etc at the other end, GI wire encased in and including 20 mm bore GI light grade pipe with all fittings, from top of electrode to body of equipment fixed with and including 25 x 6mm flat iron clamps, bolts, nuts and washer and also including providing watering pipe 20mm bore GI pipe light grade and including funnel, wire mesh, copper lugs etc from bottom of earth pit to top of electrode complete with earth pit in PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate and CI cover complete all specified and shown in electrical plate No 05 of SSR Pt-I connecting earth electrode to test point with and including earthing lead including necessary excavation and earthwork in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50m, material and labour complete all as specified and as directed by Engineer-in-Charge. (Notes 1. The rate quoted shall be deemed to include for all the above provisions. 2. PCC chamber shall be constructed at least 1.5 m away from the earth electrode and pipe for watering shall be provided in slanting manner).

Surface dressing/ cleaning of surrounding area of LT panel / two pole/four pole structure/ substation/transformer area/sub station and surface including removing of tree branches complete all as specified and as directed by Engineer in charge

Taking out old underground LT Cable of size 10 sqmm to 120 Sqmm of 3.5 core from LT Panelstrenches/floors /road/wall/ pipe/pole/including taking out loop from trenches upto 1.5 mtrs depth, cutting the faulty end of cable and refixing the cable in original position by using flat aluminium sockets/ thimble/ and insulating the all nacked wires of any size including making connection with MCCB's/ Switches complete all as directed by Engineer-in-Charge. Note : Exacavation for taking out LT cable from will measured and paid separatly.

Supply and fixing in Bus Bar Chamber cubical type of size 80x50x40 cm (Box size), with bus bar chamber having 4 wire 415 Volts, factory made dust proof vermin proof for out door using made out of CRCA sheet 3.15 mm thick powder coated, machine pressed, both side opening in two halves with provision of rubber beadings and locking system, including aluminium bus bar of 400 Amp capacity, 4 strip mounted on DMC/Epoxy insulator, bus bar chamber shall be provided with inspection covers, each MCCB/ cubical switch shall have independent opening , panel shall be mounted on angle iron frame and legs made from angle of size 40x40x6mm , frame and legs duly spray painted internally and externally with two coats of synthetic enamel paint over a coat of red oxide primer, legs grouted in PCC (1:2:4) type B-1(using 20 mm graded stone aggregate) complete including the following accessory complete all as directed by Engineer-in-charge.(i) MCCB, 200 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and tripping mechanism complete withspreader link (incoming) -01 No.

Ditto all as per item No. 27 here-in-before but using copper bus bar of 300Amp capacity and for provision of following accessory (i) MCCB, 160 Amps, 4 pole, 415 Volts, rupturing capacity not less than 25 KA, Icu=100% Ics, thermal magnetic trip with built in protection function for overload, short circuit and fast tripping mechanism complete withspreader link (incoming) -01 No.

Repair of manual operated PF control panel / micro processor based automatic power factor control panel capacity of 21 KVAR to 500 KVAR fixed on various locations including testing, checking and repair and after removing deposited dust/seals/sludge and including taking out burnt/defective items and after fixing required necessary new items ie capacitor, MCBs, circuit wiring etc all as directed by Engr-in-Chaerge.

M&L for replacement of MPP type heavy duty power factor improvement capacitor (H/D ) with connector suitable for indoor/out door operation and provided with discharge resistors of rated voltage 440 v 50 HZ 3 phase with delta connection of rating 1 KVAR to 35 KVAR all as specified Make : L/T , SIEMEN Epcos

M&L for replacement of APFC Relay 8 stage with built in multifuction meter for basic, THD and energy with 1 CT/3 CT sensing Option, smart switching, auto setup, THD protection, dual target PF, RS 485 communication, remote monitiring software complete all as directed by Eng-in-charge

Ditto all as per item No. 31 here in before but for 12 stage.

M&L for replacement of shutters made out of 3.15.00 mm thick mild steel sheet, bent to shape, including taking out old damaged unservicable shutter complete with hinges, handle etc. complete all as directed by Engineer-in-Charge.

M&L for replacement of mild steel medium weight Butt Hinges 100 mm long and fixed with steel screws complete all as specified.

M&L for replacement of mild steel medium weight Butt Hinges 75 mm long and fixed with steel screws complete all as specified.

M&L for replacement of mild steel pressed handles, size 75mm,complete all as specified and as directed by Engineer-in-Charge.

M&L for replacement of mild steel pressed handles, size 100 mm,complete all as specified and as directed by Engineer-in-Charge.

M&L for cutting/dismantling of PCC hardstanding / WBM road with soling & premix carpet of any description for repair/replacement of water supply pipe lines and disposal of debris & rubbish to a distance exc 250m but not exc 500m and making good the same with & including plain cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as existing depth complete all as specified & directed.

M&L for dismantling carefully and taking up or down existing serviceable steel water tubing and re-fixing/re-laying jointing and testing old serviceable galvanized steel water tubing medium grade of15 mm bore including cleaning the pipe from inside & outside properly including rust & mud removal with & including new fittings and fixed to walls and ceilings, roof or laid in floors/trenches in new or old position complete all as specified and directed. 1. Note for item No39 to 90:- (i) All items considered in work for repair and maitenance at DBS. (ii) All the leakage of water supply pipe lines complaints shall be rectified by the contractor within 12 hrs from the launch of complaint time. If contractor shall be fail to rectified the above said complain in given time period then a penalty @ Rs 200/day will be recovered agaist the each job. (iii) All T&P and vehicles for transportation will be provided by contractor. (iv) Items retrieved from replacement shall deposited to AGE E/M store and cost of transportation and TP shall deemed to be inluded in above

M&L for dismantling carefully and taking up or down existing serviceable steel water tubing and re-fixing/re-laying jointing and testing old serviceable galvanized steel water tubing medium grade of 20mm bore including cleaning the pipe from inside & outside properly including rust & mud removal with & including new fittings and fixed to walls and ceilings, roof or laid in floors/trenches in new or old position complete all as specified and directed.

M&L for dismantling carefully and taking up or down existing serviceable steel water tubing and re-fixing/re-laying jointing and testing old serviceable galvanized steel water tubing medium grade of 25mm bore including cleaning the pipe from inside & outside properly including rust & mud removal with & including new fittings and fixed to walls and ceilings, roof or laid in floors/trenches in new or old position complete all as specified and directed.

M&L for dismantling carefully and taking up or down existing serviceable steel water tubing and re-fixing/re-laying jointing and testing old serviceable galvanized steel water tubing medium grade of 40mm bore including cleaning the pipe from inside & outside properly including rust & mud removal with & including new fittings and fixed to walls and ceilings, roof or laid in floors/trenches in new or old position complete all as specified and directed.

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 50 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil excluding dewatering complete all as specified & as directed.

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 80 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 100 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

S&F in repairs cast iron detachable joint with rubber ring, ISI marked, Class-A, suitable for 150 mm bore cast iron pipe/specials with nuts, bolts including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

M&L for repair to existing leaking run lead joint of CI/DI pipe or fittings of 80mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil inluding dewatering complete all as specified & as directed.

M&L for repair to existing leaking run lead joint of CI/DI pipe or fittings of 100 mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of joint including necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

M&L for repair to existing leaking run lead joint of CI/DI pipe or fittings of 150mm bore spigot and socketed ends by dismantling joint by melting the lead with the help of burner/blower including taking out old spun yarn and re-jointing with & including additional quantity of Pig lead required and good quality of spun yarn and testing of jointexcluding necessary excavation & earth work in any type of soil including dewatering complete all as specified & as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 15mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 20 mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 20mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 25 mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 25mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 40 mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 40mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 50 mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 50 mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 80 mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 80mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 100 mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 100mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for galvanized steel water tubing medium grade of 150mm bore with & including all fittings complete, laid in trenches, including taking up or down old unserviceable steel water tubing and connections of 150mm bore, complete all as specified and directed. Note :- Excavation & earthwork shall be measured & paid for separately under relevant items of this Schedule.

M&L for run lead joint for 80 mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L for run lead joint for 100mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

M&L for run lead joint for 150mm bore CI spigot & socket pipe and fittings including preparation of ends & jointing materials, coupling & testing complete all as specified & directed.

Supply & fixing mild steel clamps made of flat iron 40x6mm in two halves for tapping through 40 to 80 mm bore GI/DI water pipe line including drilling and welding of 15/20mm GI socket and necessary rubber insertion, nut, bolts & washers complete all as directed.

Supply & fixing mild steel clamps made of flat iron 50x6mm in two halves for tapping through 100 to 150mm bore GI/DI water pipe line including drilling and welding of 25mm G I socket and necessary rubber insertion, nut, bolts & washers complete all as directed.

S&F 15 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 15 mm bore, complete, all as specified & directed.

S&F 20 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 20mm bore, complete, all as specified & directed.Make :- Zoloto/Vinus

S&F 25 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 25mm bore, complete, all as specified & directed.Make :- Zoloto/Vinus

S&F 40 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 40 mm bore, complete, all as specified & directed.Make :- Zoloto/Vinus

S&F 50 mm bore Gun metal gate valve (ISI marked) with iron wheel head, screwed both ends for iron pipe, including dismantling & taking out old unserviceable gate valve of 50 mm bore, complete, all as specified & directed.Make :- Zoloto/Vinus

M&L for repair to unserviceable sluice valve of size 80mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

M&L for repair to unserviceable sluice valve of size 100mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

M&L for repair to unserviceable sluice valve of size 150mm bore by dismantling and opening the gland cap and head of sluice valve and taking out the unserviceable lock nut, fitting the material on serviceable spindle, grinding the material cutting the threads by lathe machine and fabrication of new lock nut with cutting the threads inside the lock nut according to the spindle threads and refixing in the same position, testing the sluice valve, complete, all as specified and directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 80 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete, all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 100 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3 mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete, all as specified & directed.

Supply & fixing cast iron body sluice valve heavy duty class ‘PN-1.6’ of 150 mm bore, ISI marked with IS 14846, both flanged ends and drilled, high tensile stainless steel spindle, CI gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable CI sluice valve of 150 mm bore, complete, all as specified & directed. Make :- Zoloto/Vinus/BIR

Supply and fixing non return valve (NRV) of size 80mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint complete all as specified and as directed including dismantling & taking out old unserviceable non return valve.

Material only the following spare parts for centrifugal pump/Monoblock pump of 3 to 10 HP capacity (any make & Model as per site) required to be replaced under item No 1 above as specified and directed by Engr-in-charge. Note : Old Unsv/Replace items deposited to AGE E/M Store Yard including transportation and labour by contractor no extra payment made on this account (a) Inter stage ring

(b) Gland Cap CI with nut bolt complete

(c) Gland/pump sleev bush/bushing SS type

(d) Wear ring CI

(e) Shaft Sleeve Bronze

(f) Shaft Sleeve Nut (Bronze)

(g) SS pump shaft as per existing

(h) GM impellar comlete with impellar key

(i) Gasket set manifold

(j) Air release cock brass type as per site

(k) Cooling pipe for Gland (2 Nos)

Taking down of defective induction motor of 03 TO 05 HP capacity and make from the foundation, disconnecting the electric connecting coupling pulley, and transporting to work shop cutting down and removing existing burnt out copper windings, cleaning of slots and rewinding with solid copper conductor ( winding wire) complete including varnishing, drying, ovening, overhauling, greasing and fixing in the same position, making necessary electric connection and testing of induction motor complete all as specified and as directed by Engineer-in-Charge. Note : Old Unsv/Replace items deposited to AGE E/M Store Yard including transportation and labour by contractor no extra payment made on this account.

M&L in replacement of metallic antivibration pads with rubber cushion for 75/60/50/40/30/25/20 HP motor pumping set including drilling hole at necessary places on foundation base frame. MAKE: Dunlop or existing make

Cleaning of over head tank by desludging, scraping the bottom, sides wall and upper bottom with the help of scrapper/wire iron brush removing all scales, cracked earth, dirt, mud/slit algi, fungus and other foreign deposited materials including dewatering the left over water complete and making of one coat by bleaching powder for disinfection of OHT inner side complete all as directed by Engineer-in-Charge from RCC over head tanks 50,000 Gallons.

Cleaning of under ground Sump capacity 150000 Gallons by desludging/ scraping the bottom, sides, upper bottom and walls (Internal) with the help of scrapper/wire iron brush, removing all scale, dirt/mud, caked earth, slit and deposited materials including other foreign deposited materials including dewatering the left over water and taking them out complete and painting of one coat by liquid bleaching powder inner side of UG Sump complete all as directed by Engineer-in-Charge.

M/s Rohit Construction Co. (BID ID -3442579)

Gill Construction Co (BID ID -3442693)