REPAIR REPLACEMENT TO PATHS PAVER BLOCKS HARD STANDING OUTDOOR TILES ETC AND OTHER CONNECTED MISC WORKS AT PARADE GROUND BHARATPUR MIL STN

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified.

M & L rendering 15 mm thick in CM (1:4) on brick work or concrete surfaces finished even & smooth without using extra cement, complete all as specified.

All as per item No 2 but in CM (1:6) finished even and fair complete all as specified.

M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces including finished even & smooth without using extra cement on ceiling complete all as specified.

M&L for two coat of exterior emulsion paint over a coat of primer , white or tinted including preparation of newly plastered surfaces complete all as specified.

M & L Preparation of new decorated plastered surfaces of wall including cornices, pilasters etc by brooming down and applying two coats of cement base paint of approved shade on walls with hand roller complete all as specified .

M & L Preparation of new decorated plastered unplastered surfaces surface of wall including cornices, pilasters etc by brooming down and applying Three coats of white wash on walls complete all as specified.

M & L Preparation of new decorated plastered unplastered surfaces surface of wall including cornices, pilasters etc by brooming down and applying two coats of oil bound distemper over 1.5mm wall care putty(Two Coat) of approved shade on walls by roller complete all as specified.

M&L for three coats of white wash on new plastered or unplastered surfaces of Ceilings including prepration of surfaces complete all as specified.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoin jambs pillars etc.complete all as specified.

M&L Brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified .

All as per item No 11 but except bricks complete all as specified.

Demolition of PCC in ground floors and pavings not exc 15cm thickness ( below or above ground level ) Complete all as specified.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection, 75mm thick finished even and smooth without using extra cement complete all as specified.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in flooring 40mm thick finished even and smooth with using extra cement complete all as specified.

M&L 100 mm thick PCC 1:4:8 type D-2 using 40mm graded aggregate sub basefilling complete all as specified.

M&L for 80mm thick & M-40 factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould/rubber molded, laid in required colour & pattern over and including 25mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as specified.

M&L for factory made kerb stone of plain cement concrete (1:2:4) type B-1(using 20 mm graded stone aggregate) , of size depth 450mm , thickness 150 mm and length n.exc. 500 mm set and jointed in cement mortar (1:4) incl painting work complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ), removing serviceable tiling to store and rubbish off the premises complete all as specified.

M & L for Endura Designer Collection Series of Jhonson Tiles/ Kajaria or somani tile of size 300x300x10 mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 15mm thick base of cement mortar 1:4 in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete all as specified.

M&L coloured Glazed ceramic tiles in vertical surface 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over and including 10 mm thick plaster in CM (1:4) complete all as specfied.

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm , over and including 15 mm thick screed bed in CM 1:6 in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L for Vitrified Light Shade ceramic tiles 10 mm thick (Square/rectangular) area of each tile not exceeding 0.36 sqm , over and including 15 mm thick screed bed in CM 1:6 in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified.

Dismantling of stone slab and tiles of any description or thickness in floors, etc laid beded and pointed in any mortar complete all as specified.

M & L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including point?ing in white cement (1:2) us?ing marble dust with admix?ture of pigment to match with shade of granite over and including 15mm thick screed bed in cement mortor 1:4 complete all as specified.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over and including cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified .

M&L for Machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

S &F triple layered (White Colour) rotational moulded polyethylene water storage tanks 500 Ltr (cylinderical vertical with closed top) with 20mm dia ball brass valves,high pressure , with polythene float and flynut including dismantling of existing water tank of capacity exc 250 Ltr & n exc 500 Ltr, complete all as specified.

S & F in repairs for single piece-WC with UF soft close slim seat cover, fixing accessories, accessories set and cistern fitting, size 365x 655x 760mm strap 220mm complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation, boards/slabs/blankets, any thickness, including cover fillets and frame work complete all as specified.

S&F PVC wall panelling with panel of 300 mm x 6 mm Hollow section of Sintex pattern SPUF- 146 or equivalent , fixed with PVC plug and screw and inserted to next panel groove, edges and corners of all door/ window/openings etc to be covered with PVC angle fixed with solvent cement complete all as specified.

M&L for providing and fixing Gypsum Board 12 mm thick in ceiling fixed with screws instructions Complete all as specified.

S&F anodised aluminium snap grid frame work of size 605x605mm for false ceiling complete all as specified.

S&F hangers 6mm dia. G.i. (up to 1200 mm length ) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60 mm long and hold fasterners 12.5mm dia 40mm long.complete all as specified .

Dismantling of Stone Jali & Stone Pillar of any description , any thickness complete all as specified.

M&L for 40 mm thick Sikandra stone jali decorative design of approved pattern by GE including all carving and moulding of corners fixed in cement mortar 1:4 to grooves of stone pillars application with colouring to match with colour of jali including fixing of stone jali for all corners & lift complete all as specified.

S&F stone pillars(post) of size 100x100 mm including engraving decorative design of approved pattern on two face and dome shape approved by GE , height of each post as per sikandra jali, ,making groove on two face of size 43x5 mm for fixing of sikandra Jali in CM 1:4 complete all as specified.

Taking down chowkats or frames n. exc 1.5 sqm each with shutters (without taking off shutters from the frame)complete all as specified.

Taking down shutter of any description area exc 1 sqm and n. exc 2.50 Sqm each complete all as specified.

Taking down chowkats or frames exc. 1.5 sqm but not exc. 4 sqm each without taking off shutters from frames complete all as specified.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, complete all as specified. Note:- Rate of Door Handle ,Lock & floor spring etc of suitable size as per sample kept in GE office deemed to be including quoted rate )

S & F colour powder coated mild steel continuous (piano) hinge, width of flaps(when open) is 30mm complete all as specified.

S &F 18mm thick solid PVC ply of first quality of one side prelaminated of approved colour and one side white colour fixed with screw 'solvent cement/adhesive to make cupboard shutter complete all as specified.

S & F stainless steel handle of 110mm size of best quality complete all as specified.

S & F magnet catch for kitchen cabinet shutter as per approved sample complete all as specified.

S & F colour powder coated mild steel continuous (piano) hinge, width of flaps(when open) is 30mm complete all as specified.

M&L for powder coated aluminium glazed window/ ventilator shutters with frame openable using 100 x 45 x 2.00mm thick aluminium sec for frame & section for shutter 45 x 44.45 x 1.90 mm thick incl 5mm thick glass sheet with rubber beading clip,including 75mm Al hinges (02 Nos) 100mm Aluminium handle(01) nos and 100mm Al tower bolt(02 Nos) in each shutter etc complete all as specified.

S&F powder coated Aluminium door partly glazed (using 5mm thick glass) and partly panelled (using 12mm thick both side prelaminated board ) door with bottom rail of section 114x44.5x1.5mm thick and middle and top rail and style of section 84x44.45x 1.5mm thick incl 125mm dia circular aluminium handle and 150mm tower bolt, mortice lock of brass size 65mm, vertical type with fair levers door stopper double leg rubber beading and door double action floor spring of approved make, door stopper, and aluminium frame of section 100x44.45x2.00mm thick complete all as specified.

M&L for sheet glass ordinary quality 4.8mm thick and glazing with oil putty in square exc 0.50 sqm in each pane complete all as specified.

S&F in repair Aluminium extruded section body door closer hydraulically regulated designation no 3 universal type suitable for door shutter up to 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified.

Dismantling of steel rolling shutter of any description and any size complete all as specified.

M&L for greasing and easing of rolling shutter of size not exc 18 sqm alonwith the guide channel,helical spring,anchoring as to work the shutter in easy way complete all as specified.

Steel rolling shutters,thickness of lath 1.00mm without ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer;erected in position as indicated,but gear operated type with bevel gear box and crank handle complete all as specified.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified.

S&F Ball bearing for rolling shutters complete all as specified.

GOVIND CONSTRUCTION (BID ID -3342059)

K P BUILDERS (BID ID -3332318)

Swastik Engineering Works (BID ID -3350621)

Tulsi Enterprises (BID ID -3341779)

abhinav and company (BID ID -3349945)

VASUNDHARA AND COMPANY (BID ID -3341732)

krishna Associate (BID ID -3340452)

m/s meetu enterprises (BID ID -3350197)