Construction of Dhalli Bye pass to Helipad road km. 0/00 to 0/300 (SH Providing and laying G-II, G-III and Crash barrier in parking )(Balance work

Amount

Construction of embankment with approved material obtained from borrow pits with in all hights, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with in all lead & lifts as per Technical Specification Clause 301.5 as per directions of the Engineer-in-Charge.

Consolidation of sub grade with road roller including making good the undulation etc. with earth or quarry soil etc. and re-rolling the sub-grade completed as per HP PWD specification including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening /binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density grading 2(two) as per Technical Specification Clause 405 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 3(three) as per Technical Specification Clause 405 including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge.(i) 1:4:8 (one Cement : four coarse sand) : eight graded stone aggregate 20 mm(twenty milimetre) nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level including carriage of materials in all leads and lifts as per directions of the Engineer-in-Charge (i) P.C.C. grade 1:2:4 (one cement : two coarse sand) : four graded stone aggregate 20 mm(twenty milimetre) nominal size)

Providing and Fixing Single "W" Metal beam crash barrier comprishing of cold formed W profiled section having thickness of 3 mm (three milimetre)(uncoated thickness ) with frame width of 311 mm(three hundred eleven milimetre) depth 83 mm (eighty three milimetre)and length 4318 mm(four thousand three hundred eighteen milimetre) (made of ISI marked HR coil conforming to IS : 5986/2011) , to be fixed on cold formed channel section post of size 150x75x5 mm (One hundred fifty into seventy five into five milimetre)( Made from ISI marked Hr Coils conforming to IS 5986/2011) spaced 1.50 metre(one point five zero metre) centre to centre of the post which will be of total height of 1.80 metre(One point eight zero metre) with its height of 1.1 metre(One point one metre) below ground level and 0.70 metre(zero point seven zero metre) above ground level. Metal beam rail to be fixed on the vertical post with spacer channel of cold formed channel section size 150x75x5 mm and 330 mm(One hundred fifty into seventy five into five milimetre) and (three hundred thirty milimetre) long (made from ISI Marked HR coils conforming to IS : 5986/2011 ) , All the above components shall - conform to clause 810 of MORTH & H specifications including all fittings required for erection on road side W-Beams, Posts , Spacers shall be hot dip galvanised with Zinc coating of 550 gm/Sqm(five hundred fifty gramt/swquare metre). All bolts , nuts and washers shall be hot dip galvanised to IS :1367 pt-XIII/1983 ( Reaffirmed 2011 ) for bolts and IS 14394/1996 ( reaffirmed 2011 ) for nuts including carriage of materials in all leads and lifts as per the direction of Engineer-in- charge.

Sanjeev thakur