SPECIAL REPAIR TO SNCOs LIVING IN BILLETS AT 7BRD AND PROVN OF CERTAIN MINOR WORKS AT 7BRD UNDER GE (AF) TUGHLAKABAD

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site.

Taking down shutters of any description exc. 1 sqm and n. exc. 2 sqm each and removing from site.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings ass as directed by Engineer-inCharge.

M&L Flush shutters, 30mm thick solid core construction, with block board core and plywood face panels, commercial type on one sides and decorative on other side all as specified and for 0.90 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per maker's instructions.

S&F galvanised mild steel wire cloth of 0.56 mm nominal dia of wire and 1.18mm average width of aperature and fixed with beading tinned tacks or galvanized wire staples in steel/wooden window/door fixed with nails/welding complete all as specified.

S&F in repair sheet glass 4 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n.exc. 0.5 sqm in each pane.

S&F stainless steel butt hinges, medium weight of size 100 mm.

S&F in repair medium weight colled rolled butt hinges, medium weight of size 100 mm.

S&F 150 mm long stainless steel barrel tower bolts of extruded section and fixed (ISI Marked).

S&F 100 mm long stainless steel barrel tower bolts of extruded section and fixed (ISI Marked).

S&F 250 mm long stainless steel sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections of stainless steel (ISI Marked).

S&F stainless steel handles, fabricated type of size 150 mm (ISI Marked).

S&F stainless steel handles, fabricated type of size 100 mm (ISI Marked).

S&F 300 mm, mild steel, ordinary helicalsprings including roller and roller plate complete.

S&F Continuous (piano) hinges, stainless steel steel, bright finish or electrogalvanised

Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide or zinc chrome primer.

M&L for preparation of new wooden surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of aluminium wood primer.

S&F of 150 mm floor door stopper of aluminium alloy body and tongue andodised with hard drawn steel spring fixed in floor

Supply and fixed in repair of 300 mm aluminium alloy anodised sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed.

M&L for welding in repairs n. exc. 2.5 cm in length, thickness of metal to be welded n. exc. 6 mm.

Dismatling floor hearth or wall tiling including cement mortor bedding but not backing removing serviceable tiles to store and rubbish off the premise

S&F Glazed ceramic tiles coloured in vertical surface 300x200x7mm thk/Size matching with existing tiles, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick backing coat in CM 1:4 .

S&F Aluminium powder coated aluminium frame for doors , windows, ventilators, partion wall with one or more rebates including joining cleat for fixing etc completet all as specified. (thikness of powder coating is 40 micron)

S&F aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) door shutters, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, aluminium snap beading screws complete all as specified.

S&F aluminium powder coating of any colour (Thickness of powder coating not less than 50 micron) window and ventilator shutter side hung type without sashbar, aluminium sections weighing 0.55kg/m incl necessary joining cleat glazing clips, rubber neoprene packing, alumimium anodised snap beading, screws , peg stay 150mm long -1 No, hinges type B-21 100mm long -2 Nos, suitable handle -1 No complete all as specifiedhandles 2 Nos in each door, hinges, aluminium snap beading screws complete all as specified.

S&F 5.5 mm thick froasted glass panes and glazing with oil putty or fix in aluminium door / widnow complete all as specified.

M&L for powder coated (min 50 micron) aluminium three track sliding window with extruded profile of top bottom & side track for fixing 5.5mm thick tinted glass fitted with glazing clips and EPDM rubber in two shutters and fixing SS wire mesh in one shutter and powder coated deco grill including roller and handle complete all as specified and directed. Note:- (a) including 5.5mm thick tinted glass, SS wiremesh, Deco grill etc in this item. (b) Framed section 3 track size = 92x31.75x1.5mm (c) Shutter section size = 40x18x1.55mm

S&F 18 mm solid PVC ply of 1st quality of approved colour and fixed with screw, solvent cement/adhessive complete all as specified and directed by Engineer-in-charge.

S&F 18 mm solid PVC ply of 1st quality of both side white colour fixed with screw, solvent cement/adhessive complete all as specified and directed by Engineer-in-charge.

S&F 12 mm solid PVC ply of 1st quality of both side white colour fixed with screw, solvent cement/adhessive complete all as specified and directed by Engineer-in-charge.

S&F brass Locks for cupboard/Glass doors, grade I, size 50mm

S&F Magnetic catcher for Wardrobe, Cub-boards Etc.

S&F sliding channels for holding glasses in wardrobes

S&F stainless steel Pivot hinge of size not exc. 75 mm for glass doors complete all as specified and directed

S&F in repairs double action floor spring hydraulically regulated made up of of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of mild steel heavy duty and fixed

Demolition of cement concrete (Unreinforced) in ground floor & paving n exc 15 cm thick (below or above ground level).

M&L for 100 mm thick Cement concrete type D-2, (1:4:8) using 40mm graded stone aggregate complete all as directed.

M&L for Cement concrete Type B2 (1:2:4) using 40 mm graded stone aggregate in foundations, filling and mass-concrete.

Supply and fixing in repairs 7mm thick aluminium grill of make ' Deco grill DG-104 model fitted in to suitable aluminium channel and fixed to windows / ventilators including channel complete all as directed by Engr-in-charge.

S&F in repairs stainless steel curtain rod of dia 20-25 mm complete as approved.

S&F Stainless steel bracket with finels for holding curtain rodes of dia 20-25 mm as approved

M&L for gunniting to RCC works in column,beams, slabs, chajja, facia, landing, balconies etc by removing/ dismantling of RCC(loose concrete) including plaster and cutting of steel bar including plaster cleaning of surfaces with wire brushes and applying epoxy, paint anti corrosive coating of minimum 40-50 microns thick with sikatop Armatec 108 or Colusal VL of MC Bauchemie to rusted steel reinforcement after removing cleaning all rust and supply and fixing welded steel wire mesh 75mm x75mm with 4mm dia steel wire as facies/drops and similar works etc and expoxy based or other equivalent suitable bonding against treatment to be carried out on old concrete surface with Sikadur 32 of Sikka. Nito bond EP of fosroc or equivalent (as per manufacturers instruction) to bond old and new concrete mixing @ 2% by weight of cement polycrete and providing gunniting with a minimum pressure of 2 to 2.5 Kg sqcm and applying 25mm to 100 mm thick gunniting in cement mortar (1:2) (one part of cement and two part of ghaghar sand) with plastering(1:4) using ordinary port land cement of 43 grade over wherever required at any height, complete all as specified and directed by Engineer-in-Charge. Note:-(i) After placing the additional reinforcement all concrete surface shall be thoroughly scrubbing with. (ii) Additional reinforced TMT bars where incorporated in work and including 20mm thick cement plaster in 1:4 to be included in quoted rate. (iii) Work to be carried out as in patches as directed by Engr-in-charge. (iv) Rate for steel scaffolding as directed to be included in quoted rate. (v) All demolished material removed from MOD land completely.

M&L for mild steel TMT bars 10mm dia and over cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified.

M&L TMT steel bars 6mm to 8mm dia and over cut to length bent shape required, including cranking bending binding with mild steel wire (annealed) not less than 0.9mm dia quality conforming to relevant IS complete all as specified.

Re-baring by drilling holes and fixing nozzle if required in existing concrete/brick work as in column, beams, slabs and foundation etc in any position and any description size of hole 14mm, 16mm & 22mm suitable for dowels of size 10mm, 12mm & 16mm respectively (minimum depth 140mm for 10mm & 12 mm dia bars and 180mm for 16mm dia bar, cleaning the surface properly with blow out pump & round brushes and fixing of dowel bars with epoxy resin (resin+hardner) complete all as specified and directed by Engr-in-charge. Make: Sika, Fosroc or concressive 1450 of BASF Note:- (i) Adequate lap length shall be provided as per IS-456-2000. (ii) Reinforced TMT bars where incorporated in work will be paid under item no 45 & 46. (iii) The work shall be carried out upto four storied building with scaffolding.

Taking down loose cement plaster on brick, stone walls and concrete surfaces(except above mention in description 1 area) of any description/position etc including racking out joints, hacking for keys scrubbing down with water etc complete all as specified and directed by Engr-in-charge.

M&L for 10 mm thick cement plaster with readymix plaster (as per manufaturer's instruction) on fair faces of brick wall or concrete surfaces finished even and smooth, (without using extra cement) complete all as specified and directed by Enigneer-in-Charge. Note:- 1. Make of readymix plaster shall be Birla Aerocon/ Ultratech readiplast/ACC Accoplast / Fosroc Chemical (India) Pvt Ltd Renderoc and as approved by GE) 2. The readymix plaster shall be procured directly from the manufacturer or their authorised dealer. 3 The contractor shall produced original purchase voucher alongwith test certificate of readymix plaster by manufacturer or their authorised dealer while claiming RAR/ Final Bill.

M&L for 15 mm thick cement plaster with readymix plaster (as per manufaturer's instruction) on fair faces of brick wall or concrete surfaces finished even and smooth, (without using extra cement) complete all as specified and directed by Enigneer-in-Charge. Note:- 1. Make of readymix plaster shall be Birla Aerocon/ Ultratech readiplast/ACC Accoplast / Fosroc Chemical (India) Pvt Ltd Renderoc and as approved by GE) 2. The readymix plaster shall be procured directly from the manufacturer or their authorised dealer. 3 The contractor shall produced original purchase voucher alongwith test certificate of readymix plaster by manufacturer or their authorised dealer while claiming RAR/ Final Bill.

M&L for 5mm thick rendering in CM (1:3) on concrete/gunniting surface as in ceiling finished even and smooth w/o using extra complete all as specified and directed by Engr-in-charge

M&L for two coats of cement base paint over a coat of primer on newly plastered surface of walls to match the exixting colour incl preparation the surface complete all as specified (External)

M&L for preparing newly surfaces of ceilings and applying three coat of white wash on new surface all as specified.

Cleaning of roof slab/chajja with sweeping with brooms, removing complete all as specified and directed by Engr-in-charge.

Taking down old existing roof treatment of any type including mud fuska and removing from MoD Land complete all as specified and directed by Engr-in-charge.

Brushing neat cement slurry with 3kg of cement per Sqm complete all as specified and directed by Engr-in-charge.

M&L for min 25 mm thick cement concrete (1:2:4) type B-O using 12.5 mm graded stone aggregate in padding finishing surface of concrete topping even and smooth without using extra cement complete all as specified and directed by Engr-in-charge.

M&L for 10mm thick plastering in CM (1:3) on green concrete roof surfaces Sqm with water proofing compound @ 3% by weight of cement, surface finished even and smooth without using extra cement complete all as specified and directed by Engr-in-charge. Note - WPC shall be measured and paid separately.

Supply only integral water proofing compound ISI Marked complete all as specified and directed by Engr-in-charge.

M&L for preparing new surfaces and applying two coat of Polyurethane (PU) based Water proofing liquid compound as per manufacturer's instruction to stop leakage/seepage from roof/wall complete all as specified and directed by the Engineer-in-Charge.

Dismantling of existing water tank (PVC/RCC/AC) exc 500 ltr but n exc 1000 ltr capacity and removing from site to store yard complete all as specified and directed by Enar-in-charge.

S&F 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball PTMT valve high pressure with polyethylene float and fly nut complete all as specified and directed by Engr-in-charge.

Dismantling of existing water tank (PVC/RCC/AC) exc 250 ltr but n exc 500 ltr capacity and removing from site to store yard complete all as specified and directed by Engr-in-charge.

S&F 500 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm bore ball PTMT valve high pressure with polyethylene float and fly nut complete all as specified and directed by Engr-in-charge.

S&F in repair Pre- painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

S&F in repair Colored Polycarbonate Sheets 6mm thick (multi wall) as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Dismantling of wrought iron or Mild Steel work of any description complete all as specified and directed by EIC

S&F joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc (cut to ordinary lengths i.e. with in 20 mm of the length indicated to FE 410-W (Gde-E-250 quality-B) complete all as specified and directed.

M&L for preparation of new steel surfaces exc 10cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxideprimer all as specified.

S&F PVC (SWR) pipes single socketed 110mm dia in any length with rubber ring joints fixed to walls

S&F PVC (SWR) bends 110mm dia any radius complete all as specified and as directed.

S&F in repair of Health Faucet with 1.5 mtr long SS tube and hook make :- Prayag/Jagaur/Volga

S&F in repairs of wash down water closet EWC floor mounting with soft close seat cover and twine flush cisturn fitting 520x360x390mm complete fix in repair Make : Cera, cat part No s1059102 P trap 100mm or equivalent

S&F in repair of PVC low level flushing cistern of 10 ltrs capacity with top push buttion inclusive of brackets and PVC bend long type and connectin to flush pipe of any size and pattern with inlet ball valve float and handle complete of approved make

S&F in repair of wash hand basin of size 550 x 400 mm vitrous China white flat back including brackets, waste coupling & PVC waste pipe of 32 mm dia etc. complete all as specified and directed.

S&F in repair of 32 mm bore of pipe low density (LDPE) of pressure rating 6 kg/ sqcm fixed to wall or floor etc including fittings complete all as specified and as directed.

S&F in repair of 15mm bore chromium plated Pillar cock screwed down high pressure, with or without lettered Hot ot Cold with long screwed shanks and flynuts screwed for iron pipe complete all as specified.

S&F in repair of PVC connection 15 mm size with PTMT nuts of length 450 mm of approved quality

S&F in repair of 15 mm bore Angle stop valve cast copper alloy screwed down high pressure with crutch butter fly handle screwed both ends for iron pipe or for unions and fixed all as specified

S&F in repair of brass chromium plated shower rose 125 mm of size with arme and with or without swivel joints to steel pipe or union complete all as specified and as directed

S&F in repair of 15 mm dia bore concealed stop valves cast copper alloy chromium plated fancy type with long shank & cup (concealed type) complete all as specified and as directed.

S&F in repair of brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges.

S&F in repair of CP soap tray fixed to walls with rubber plugs complete all as specified and directed.

S&F in repair of 15 mm dia bore bib taps cast copper alloy with crutch and butterfly handle, screwed for iron pipe, or for brass ferrule complete all as specified and as directed.

S&F in repair of sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm, etc complete all as specified and as directed.

S&F in repair of 125mm dia grating doom with/without waste hole of PTMT (Minimum weight 40 gms)

S&F in repair of PVC bath room cabinet with mirror of size 432 mm x 311 mm complete all as specified and as directed.

Taking up or down GI tubing /PPR pipe15 mm bore pipe all as specified and as directed.

Taking up or down GI tubing/PPR pipe 20mm bore pipe all as specified and as directed.

S&F of GI tubing 15 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 15 mm complete all as specified.

S&F of GI tubing 20 mm bore medium grade galvanise with all fitting and fixed to walls & ceilings or laid in floors, bore of pipe 20 mm complete all as specified.

S&F in repair of glazed ceramic coloured tiles 7mm thick 450 x 300mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. Etc including 10 mm thick rendering in CM 1:4 complete all as specified.

S&F vitrified tiles 10mm thick (Square/rectangular) polished in dark shade, area exc 0.42 Sqm but n exc 1.00 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortor 1:6.

S&F vitrified tiles 10mm thick (Square/rectangular) polishedin light shade, area n exc 0.36 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cement mortor 1:6.

Material & labour for GVT (Glazed vitrfied tile) tiles light coloured of size 300x450mm and thickness more than 9mm, on vertical surfaces such as skirting/dados etc set & jointed in neat cement slurry & pointed in coloured cement to match the shade of ties including and over rendering 15 mm thick in CM 1:4 on wall complete all as specified and directed

Material & labour for full vitrified dura stone 10mm thick heavy duty coloured tiles of size 600x600mm in floors etc set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles with spacer and tiles laid with laticrate 315 chemical complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed 15mm thick in cement mortor 1:6 jointed with grey cement slury moxed with pigment to match the shade of the slab including rubbing and polishing complete

M&L 20 mm thick granite work (table rubbed and polished) on bar counter, cooking pisteform pillars cill jambs, steps and like over 15 mm thick in CM 1:4 ind pointing in white cement (1:2) using marble dust with admixture of pigment to maten including bull nosing the edge complete.

Supply & Fixing for roof covering by polyurethane Foam (PUF) wall panel of 60mm thick with boath side PPGI sheet of 0.5mm thickness All material shall comply with relevant BIS The outer colour coated sheet GI skin (RAL 7032) of the panel shall be 0.5mm thick TCT (Total coated thickness) with 50 micron PVC quard film on the finished surface only for protection against scratches during handling and transpotation Base metal of GI skin CRCA shall be as per IS 513 and galvanization as per GR-120 s277 The pre-coated GI sheet skin shall have minimum coating of 5 micron epoxy primer and 25 micron polyester top coat on the finished surfaces and 7-8 micron primer Alkyd Backer on the backside which is bounded to polyurethane foam The pre-coated Gl sheet shall confirm to the IS 14246-1995. All the opening and sheet terminations to be closed with appropiate factory made flashing/Trims (Ridge comer flashing. Gable Ends, framed opening etc). Colour of the materials same as roof/wall/liner panel Eave gutters, downspouts and rain water down take pipes are cold formed from the same materieals (coolr & finish) as wall panels ar approved by GE

M&L Andised aluminium snap grid frame work (600mm x 600mm) for false ceiling complete al as specified

Supply & fixing 10mm PVC inculation panel with EPS stuck to 1mm plain PVC sheet suitably placed in false cilling grid made of aluminium as per specification and drawing.

M&L Cutting holes in brick in floor and walls in cement mortar exo half brick but not exc one brick for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required

S&F 18mm solid PVC ply of 1st quality of one side prelaminated of approved colour and one side white colour fixed with screw solvent cement/adhessive complete all as specified and directed by Engineer-in-charge

Supply and fixing Stainless steel handle of 110mm size as per approved sample for kitchen cabinate shutter complete all as specified and directed

Supply and fixing in repairs of vitreous china WHB white flat back size 550mmx400mm with pedestal on new brackets excluding taps waste china & plug including bracket etc complete all as specified and directed Engg-in-Charge

M&L 25mm thick PCC 1:2:4 type B-0 (12:5mm graded stone agg) as in sub base to received tiles in floor

M&L RCC (nominal mix) type B1 (1:2:4) (20mm graded aggregate) in slabs supported on walls, bearms and columns in floors, roofs, landings, balconies canopies dech

Taking down carefully copper/aluminium point wiring (light/fan/socket power) complete, including fixture and fitting such as switches, ceiling roses, pendents, regulators, sockets light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc by applying necessary periodically with one coat of putty and two coats of OBD to match with the surroundings complete all as specified and directed by Engr-in-Charge.

Taking down existing sub main wiring of any type and description including removal of teak wood batten/pipe etc and making good surfaces by applying necessary periodically with one coat of putty and two coats of OBD to match with the surrounding complete all as specified & directed by Engineer -In-Charge.

M&L for point wiring complete with 1.5 Sqmm (nominal area) PVC insulated, multi stranded, FRLS copper conductor cable unsheathed in and include PVC conduit with all fittings medium grade ISI Marked and PVC insulated FRLS copper conductor cable of size 1.5 sq mm as earth wire , connected to common earth dolly suitable for mounting modular switches incl modular metal flush boxes and modular face plate all as specified and as directed by Engr-in-charge Note: 1) Cost for cutting chases and making good to match the existing surface shall be deemed to be included in the quoted rate. 2) Rates are deemed to be inclusive of Modular GI gang box & cover plates of any module & Qty as required on site.

One light/fan/bell point controlled by one piano type switch 5 Amp single pole one way.

One socket outlet 3/5 pin 5 Amps controlled by one switch on same board.

One socket outlet 3/5 pin 5 Amp controlled by one switch on independent board.

One socket outlet 05 Amps on independent board with two single core 2.5 Sqmm drawn through in and including PVC concealed conduit pipe 20 mm dia medium grade ISI marked complete with one run of PVC insulated copper conductor cables 1.5 Sq mm single core green colour earth wire and connecting to earth dolly including colour coding of cable shall be for phase, neutral and earth wire complete all as specified and as directed by Engr-in-charge.

S&F in replacement of modular switch piano type single pole two way, 10 Amp 240 Volts AC complete all as specified & directed by Engineer - In-Charge.

S&F in replacement of modular switch piano type single pole one way, 10 Amp 240 Volts AC complete all as specified & directed by Engineer - In-Charge.

S&F in replacement of modular switch piano type 16 Amp complete all as specified & directed by Engineer - In-Charge.

M&L in replacement modular Socket outlet 6 Amp, 5 pin 240 volts multi socket for cell phone pin or 2/3 pin complete all as specified & directed by Engineer - In-Charge.

M&L in replacement of modular Socket outlet 16 Amp, 6 pin 240 volts twin Socket heavy duty complete all as specified & directed by Engineer - In-Charge.

M&L for concealed submain of wiring complete with two run of 6 sqmm (nominal area) PVC insulated multi stranded FRLS copper conductor cable unsheathed drawn through and including 20 mm dia PVC conduit medium grade ISI marked duly concealed by cutting chases and making good to match with surrounding including necessary perodicals applying one coat of putty and two coat of oil bound distember along with PVC insulated FRLS copper conductor cable of size 4 sqmm as earth wire connected to common eartyh dolly complete all as specified and as directed by Engineer - In-Charge. Note :- (i) The work include cutting of chases and making good the disturbed surfaces and quoted rate deemed to be included the same aspect. (ii) One run of conduit with accessories, three runs of 4 sqmm copper conductor will be measured as one unit of RM.

All as above item no. 117 but of size 4 sqmm

S&F single pole and neutral enclosure with a two pin and earth including plug and socket complete set with one single pole MCB of 20 Amps complete all as specified and directed by Engr-in-charge.

S&F in replacement of modular ceiling fan regulator suitable rotary step type electronic of 100 watt and two module complete all as specified and directed by Engr-in-charge.

S&F in repairs of Ceiling Rose, 3 phase/PVC/ polycarbonate isolated body complete all as specified & directed by Engineer - In-Charge.

S&F LED tube light fitting 1x20 watts (4 feet), T-8 LED fitting including Tube of 20 Watt in cool white, 230 Volts energy saving, environmental friendly, ling life, impact proof, surface mounting, batten suitable for use single LED tube made out from CRCA sheet steel coated for improper resistance against corrosion with PC housing in opal finish suitable for wet location with brightness LEDs with all accessories internally prewired and including connected with twin core twisted flexible wire copper conductor cable with suitable size complete all as specified and directed by Engr-in-Charge.

S&F in replacement of sheet metal enclosure for MCB DB single pole and neutral 8 way with 200 amps rated bus bar, 240 Volts double door type complete all as specified and directed by Engr-in-charge.

M&L in replacement for MCB SP upto 40 Amps, 240 Volts complete all as specified and directed by Engr-in-charge.

S&F in repalcement of MCB SPN of capacity 63 Amps ,240 Volts complete all as specified and as directed by Engineer -in -charge .

S&F in replacement of LED building light luminaire 45 watt pressure die cast aluminium housing with heat resistant toughtened glass and IP 65 protection complete all as specified and as directed by Engineer -in-charge. Make: Crompton cat No: LSTS-45-CDL or equivalent make of Philips /Wipro/C&S/Havell's. Note: Twin core copper wire of 1.5 Sqmm upto 7Rm required for connection of street light fitting is deemed to be included in quoted rates.

S&F in replacement bracket made of GI Pipe light grade 40mm bore bent to shape as required at site for street light fitting 1.2 m in length and fixed on wall / pole including necesary MS clamps, nuts, bolts etc complete all as specified & directed by Engineer -in-charge

FUTURE ENGINEERING

akenterprises

Rohan Construction Company

M/S S.K.Electricals

V r traders