REPAIRS TO FLOOR DADO TOILETS KITCHEN WATER SUPPLY AND PLUMBING WORK IN CERTAIN MD ACCN AT BAIRAGARH UNDER GE BHOPAL

Amount

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for Rendering 10 mm thick in cement mortar 1:4 on concrete surfaces in ceiling, finished fair & even complete all as specified and directed.

M&L for rendering 20mm thick in two coats of 10mm thick each on faces of brick work or concrete surfaces; first coat (rendering coat) in cement mortar 1: 6 and second coat (finishing coat) in cement mortar 1: 4 mixed with water proofing compound (water proofing compound to be measured separately as supply only) and finished fair and even complete all as specified and directed. Note: Water Proofing compound shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and directed. [MAKE: ACCOPROOF/WATER SEAL/MC BOUCHAMIE, MUMBAI/FOSROC/CICO/PIDILITE]

M&L for rendering 15mm thick in cement mortar 1: 4 on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Preparing new plastered or unplastered surfaces of wall and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer and including 3mm thick wall care putty (Make: Birla/JK) on plastered surfaces complete all as specified and directed.

Preparation of newly plastered or unplastered surfaces of wall and M&L for applying two coats of exterior water base emulsion paint on walls over a coat of primer, complete all as specified and directed. [MAKE : ASIAN (ACE) /SHALIMAR (SAKTIMAN) /BURGER (WALL MASTA)]

Preparing new plastered or unplastered surfaces of ceiling and M&L for applying two coats of distemper oil emulsion, white or tinted over a coat of primer and wall care putty where required (Make: Birla/JK) complete all as specified and directed. Note : Wall care putty shall be measured and paid separately.

Demolition of cement concrete (unreinforced) in any position not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing tiles/ rubbish off the permises to a distance not exceeding 250m complete all as specified and directed.

M&L for 25mm thick Cement concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate in leveling course, benching, sub base, complete all as specified and directed.

M&L for vitrified light shade flooring tiles, 10 mm thick (Square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, laid in floors, etc set and jointed in neat cement slurry and pointed in epoxy adhisive (Make :Dr.Fixit or Balendura) to match the colour of tiles with & including 15mm thick screed bed in CM 1:4 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for vitrified light shade tiles, 10 mm thick (Square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, as in vertical surfaces such as skirting, risers to steps, etc set and jointed in neat cement slurry and pointed in epoxy adhisive (Make :Dr.Fixit or Balendura) to match the colour of tiles with & including 10mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:6 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,as in vertical surfaces such as skirting, risers to steps, etc including 10mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for Non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 15mm thick screed bed in CM 1:6 complete all as specified and directed. [MAKE: SOMANY / KAJARIA / NITCO]

M&L for Glazed ceramic coloured tiles 350mm x 250mm x 7mm thick or 450mm x 350mm x 7mm thick, in vertical surfaces such as skirting, dados and risers to steps, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles with & including 10mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/ ORIENT/ JOHNSON]

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar complete all as specified and directed.

M&L for 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, moulding and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for heavy duty flooring tiles, harsh weather & UV Resistance, high abrasion resistance, MOH Hardness >6, thickness 10 mm thick, area of each tile not less than 0.09 sqm, anti slip type, laid in floors, steps, edges, etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15mm thick rendering in CM 1:4 complete all as specified and directed. [MAKE: SOMANY/ KAJARIA/ORIENT/JOHNSON]

M&L for Hard core of broken stone or boulders of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Factory made, machine pressed, M-35 grade concrete interlocking paver blocks (glossy /reflective type), with grey cement and pigment, any shape and size conforming to IS:15658-2006 (ISI Marked) of 60 mm thickness with & including 50 mm thick stone dust cushion and joints filled with sand complete all as specified and directed. [MAKE:- MEHTAB / NAVYA TILES / SAP PAVERS/ SAGAR TILES]

Taking up or down steel tubing and connections 15 mm bore, including cleaning (tubings only and not connections) for refixing complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

Refixing old steel tubing 15 mm bore, with and provision of new fittings (connections) in new or old position (walls, ceiling, floors, etc) complete all as specified and directed.

Taking up or down steel tubing and connections 20 mm bore, including cleaning (tubings only and not connections) for refixing complete all as specified and directed.

S&F Steel water tubes, medium grade, ISI marked, galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed. [MAKE: TATA/ SURYA/ JINDAL/ PRAKASH]

S&F in repairs Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size:- 914mm x 460mm x 203, bowl size:- 405mm x 354mm x 203mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.1239D Gloss) or equivalent in NIRALI/BLUE STAR as approved by GE]

S&F in repairs sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including supply & fixing cantilever brackets of mild steel angle 35 x 35 x 5 mm and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm, including CP waste coupling and 32mm dia PVC waste pipe of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.1216 Gloss) or equivalent in NIRALI/BLUE STAR as approved by GE]

S&F in repairs stainless steel kitchen plate rack overall size- 31" x 24" x 10" duly fixed on walls with gutties & screws of suitable length complete all as specified and directed. [MAKE:- Prayag (Cat No.P-340) or equivalent in NIRALI/BLUE STAR as approved by GE]

S&F in repairs Vitreous china wash basin, ISI marked, white, flat back, size 550 x 400mm, including CP waste coupling, 32mm dia PVC waste pipe of suitable length, brackets and cutting for and pinning in ends of brackets, complete all as specified and directed. [MAKE:-SOMANY (Cat No.110107) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8602) or equivalent in JAGUAR/MARC as approve by GE]

S&F in repairs Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8602) or equivalent in JAGUAR/MARC as approve by GE]

S&F in repairs bib tap standard of PTMT any colour high pressure screwed for iron pipe of 15 mm bore (minimum weight 90 gms) complete all as specified and directed.

S&F in repairs Bib taps cast copper alloy chromium plated with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8606) or equivalent in JAGUAR/MARC as approved by GE]

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed. [MAKE:- Prayag (Cat No.8610) or equivalent in JAGUAR/MARC as approved by GE]

S&F in repairs Stop valves, two way, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (angle type) screwed both ends for iron pipe or for unions 15mm bore, complete all as specified and directed.

S&F in repairs Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) screwed both ends for iron pipe or for unions 15mm bore complete all as specified and directed. [MAKE:- Prayag (Cat No.8618) or equivalent in JAGUAR/MARC as approved by GE]

S&F in repairs brass chromium plated shower rose 125 mm size with swivel joints complete all as specified and directed. [MAKE:- Prayag (Cat No.BS-73) or equivalent in JAGUAR/CERA as approve by GE]

S&F in repairs 32mm bore, PVC waste pipe suitable size for wash hand basin one metre long, complete all as specified and directed.

S&F in repairs waste coupling 40mm suitable size for kitchen sink of PTMT (half or full threaded) complete all as specified and directed. [MAKE:- Prayag/ JAGUAR/CERA as approve by GE]

S&F in repairs 40mm bore, PVC waste pipe suitable size for kitchen sink one metre long, complete all as specified and directed.

S&F in repairs 32mm bore, PVC waste pipe suitable size for wash hand basin one metre long, complete all as specified and directed.

S&F in repairs 100mm dia CP grating (Minimum weight 25 gms) including jointing with solvent cement, complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts of length 600 mm, for hot water, complete all as specified and directed.

S&F in repairs Vitreous china squatting pan ‘Orissa’ pattern, size 580 x 440 mm, white with integral foot rests including provision of cement concrete bedding & ‘P’ or ‘S’ trap complete all as specified and directed. [MAKE:-SOMANY (Cat.No.121115), PRAYAG (Cat No.4055) or equivalent in CERA/PARRYWARE/ HINDWARE as approved by GE.]

S&F in repairs vitreous china wash down water closet pan, pedestal pattern, ISI marked, white, including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed. [MAKE:-SOMANY (Cat No.120403 & 120404) or equivalent in CERA/PARRYWARE /HINDWARE as approved by GE.]

S&F in repairs PVC low level flushing cistern 10 litres capacity, ISI marked, white, with all fitting and fixtures including brackets, PVC connection of 450mm long and 32 mm bore PVC flush pipe, complete all as specified and directed. [MAKE:- SOMANY (Cat No.121002), Prayag (Cat No.501 Smart flush cistern) or equivalent in PARRYWARE-SLIMLINE/CERA as approved by GE]

S&F in repairs Mild steel chromium plated, 19mm dia, minimum thickness 1mm, curtain rod with side fixing brackets, rings & decorative knobs complete all as specified and directed.

S&F in repairs bathroom cabinet of hard thermosetting plastic of size 622 x 422 mm, fitted with superior quality distortion free 4 mm thick mirror complete all as specified and directed. [Make: PRAYAG (Model No. 555) or equivalent in NEELKAMAL/ PARRYWARE.]

S&F in repairs Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12.5 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-43) or equivalent in JAGUAR/CERA as approve by GE]

S&F in repairs corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf with chromium plated bracket guard and railing 300mm size complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-44) or equivalent in JAGUAR/CERA as approve by GE]

S&F PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches, floors or fixed to walls, 110 mm bore complete all as specified and directed.

S&F Jet spray (butterfly) with 1 mtr tube complete all as specified and directed. [MAKE:- Prayag (Cat No.BEA-18) or equivalent in JAQUAR / PLUMBER / MARC as approved by GE]

S&F hand shower (health faucet) with 8mm dia 1.0 mter long flexible tube and wall hook complete all as specified and directed. [MAKE:- Prayag (Cat No.BH-76) or equivalent in JAQUAR/MARC as approved by GE]

S&F in repairs tubular towel rail of aluminium anodised, 20mm dia, D type, 60cm long between flanges complete all as specified and directed. [MAKE:- Prayag (Cat No.BA-40) or equivalent in JAQUAR/MARC as approved by GE]

Demolition of brickwork built in cement or cement lime mortar complete all as specified and directed.

M&L for Brick work with fly ash bricks (Modular), straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Demolition to cement concrete in any position, not exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for water proofing treatment to sunken surfaces of slab in following sequence complete as specified and directed:- (a) Slope correction providing PCC 1:1.5:3 using 12.5mm graded stone aggregate, average thickness 25mm, mixed graded styone aggregate, average thickness 25mm, mixed with integral water proffing compound "DITCHTMENT DM' manufactured by Dr fixit Pidiproof LW + of M/s Pidilite Industries or STP No 1 (Liquid) of M/S STP Ltd as approved by GE, in proportions as suggested by manufacturer. (b) Applying evenly a priming coat of bituminous primer confirming to IS 3384 @ 0.7 Kg per Sqm on prepared surfaces. (c) Applying evenly a coat of hot blown bitumen of grade 85/25 @ 1.5kg/sqm on the primer surfaces. (d) Laying 150 micron thick black polythence film on the suface with 10mm overlaps sealed and bounded the surface. (e) Applying evenly a coat of hot bown of grade 85/25 @ 1.5 kg per sqm on the surfaces. (f) 48 hrs testing of treatment for water tightness by ponding of water.

M&L for 50 mm dia UPVC pipe as in water spout at the lowest point of sunken floor with 600 mm projection beyond the outer face of the wall with outer end cut in chamfered angle for easy drain of water complete all as specified and as directed.

M & L for Providing, cement concrete type B0 1:2:4 (12.5 mm graded aggregate)mixed with water proofing compound @ 3% by wt of cement in benching , roof kerbs of mud stops, rounded or chamfered on edges,cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directing (Note :- Water Proofing compound shall be measured and paid seperately)

M&L for cutting V grooves and filling cracks with polymer based chemical (Dr fixit cracks shrink free ) for cracks not exc 10 mm in width as per manufacturer instruction on wall surfaces on concrete or masonary including scaffolding etc complete all as specified and directed. Make:- Dr fixit /Berger / Perma

Taking down shutters of any description not exceeding 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

M&L for Second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in bands, straps, supports or stays for rain water, including bolts, if required, hook and pintle hinges; handmade sliding bolts; clamps; hold fasts; hooks for hanging fans and similar small articles complete all as specified and directed.

M&L for Second class hardwood 35mm thick factory made plain, framed, panelled shutter (two panels) with lock rail and panel of 9mm thick B.W.P commercial ply or 12mm thick veneered particle board with commercial veneering on both faces; size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for Second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

M&L for Second class hardwood glazed and skeleton window shutters 30mm thick, open rebated and prepared to receive glass, gauze, etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete all as specified and directed.

S&F in repairs Prelaminated particle board 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F in repairs Plain fillets of second class hard wood, square or rectangular in section, clean sawn, secured with nails or brads; sectional area exceeding 13 Sqcm but not exceeding 25 Sqcm complete all as specified and directed.

S&F Continuous (Piano) hinges, mild steel, bright finish or electro galvanized, 30 mm width of flaps (when open) complete all as specified and directed.

S&F External teak wood lipping, 6mm thick to 18/19mm thick block board or veneered particle board, fixed with nails complete all as specified and directed.

S&F in repairs Hasp and staple 100 mm size, safety type, aluminium anodised including bolt to hinge plate, fixed with screws complete all as specified and directed.

S&F in repairs 40 mm dia, cup board knobs fixed with nut, screws and washers of mild steel, bright finished complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 75 mm size complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel, 100 mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised, 100 mm size complete all as specified and directed.

S&F Aluminium handles, cast type anodised, 150 mm size complete all as specified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section, 150mm long complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames, glazed with putty or fixed with beads complete all as specified and directed.

S&F Sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

S&F Figured glass, pin head type 3mm thick and glazing with oil putty in squares not exceeding 0.5Sqm in each pane complete all as specified and directed.

Securing glass of any description in existing metal/wooden frames glazed with putty/beads including removing loose or decayed putty/beads, painting oiling one coat on rebates, grooves, to match the existing work, complete all as specified and directed. (New length of frame puttied shall be measured.)

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F Mild steel conforming to Fe-290 Gde E-165 in framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted or forged into spikes; framed guard bars; ladders; railings and similar work complete all as specified and directed.

M&L for Running welding in repairs, thickness of metal to be welded not exceeding 6mm including taking down the article and refixing in position after welding (if required) complete all as specified and directed.

M&L for Welding in repairs not exceeding 2.5 cm in length, thickness of metal to be welded not exceeding 6mm, complete all as specified and directed.

M&L for Anti-termite treatment of voids in masonry using chemical emulsion one litre per hole, at 300 mm intervals including drilling holes at 45 degree and repluging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

M&L for Anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm center to center and sealing the same complete all as specified and directed.

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for Preparing new or previously untreated surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer complete all as specified and directed.

Schedule of credit (calculation will be done off line) Rs. 23,405.00

M/s P L Dixit

POONAM ELECTRIC INDUSTRY

M/s VIKAS TRADERS

M/S Shanti Traders

H S ENTERPRISES

PADAMSHRI CONSTRUCTION CO

Samaksh Enterprises