Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹9.5 LAccepted-AOC HARI OM BHAWAN CIRCULAR ROAD UPPER KAITHU SHIMLA | L1 | Accepted-AOC L1 | |
| 2 | L2₹9.9 L+₹7,658 (0.78%)Rejected-AOC | L2 | Rejected-AOC L2 | |
| 3 | Rejected-Technical HOUSE NO 45 NEAR MONAL PUBLIC SCHOOL SANJAULI SHIMLA 171006 | SHIMLA | HIMACHAL PRADESH | 171006 | - | Rejected-Technical Not Qualified |
Tender Value
₹9.6 L
EMD Value
₹19,200
Closing Date
25 Sept 2020, 5:00 pmClosed
Executive Engineer Electrical Division No-1 HPPWD
Executive Engineer Electrical Division No-1 HPPWD Shimla-9
Providing special repair to Central Heating system in Police Headquarters at Nigam Vihar Shimla H.P
2020_PWD_40210_1
PW.ED.AB.Tender.2837.42 dt.26.08.20
Open Tender
Electrical Works
Item Rate
180 days
SHIMLA
Please refer Tender documents.
7 documents required · 7 mandatory
₹350
E.E.Electrical Division No-I Shimla
₹19,200
3 Jun 2021
3 Sept 2020
26 Sept 2020
3 Sept 2020
25 Sept 2020
3 Sept 2020
Amount
Supply installation testing and commissioning of electric element type hot water boiler /generator complete with s tank, cylindrical shell 10mm with dished ends,sheet metal enclosure, integral electrical and control panel i/c all operational and safety controls. The Boiler shall be Vertical type capacity of 300 KW capacity, bank will consist six steps with micro processor intelligent step controller and reverse flow sensor, i/c making cc foudation and complete in all respects. Make/Model: Rapid Cool, Dyna Flow or any other approved by Engineer-in-Charge.
Supply, installation, testing and commissioning of hot water piping and fittings complete with supports, hangers and specified insulation thickness. All piping shall be black mild steel Class C, ISI marked with fitting. The unit rate of piping shall include this support arrangement and hangers i/c wooden saddles where required under insulation at support points.The piping shall be insulated with 80Kg/ M.Cub. section density fiberglass insulation finally covered with 26 gauge Al. Cladding complete as required
150 mm pipe with 50 mm insulation.
Supply, installation, testing and commissioning of Gate valves/ Sluice valves, ISI marked, with flanges or screwed ends as required. Valves 65 mm and above shall of C.I. Body , with flanged ends and gunmetal trim, non-rising spindles ,P N. 1.6 and i/c flanges where required and valves upto 50mm shall be gunmetal non rising stem, integral seat, body test prssure 50kgf/cm Hyd Make/Model: KRILOSKAR, SANT, LEADER or any other approved by Engineer-in-Charge.
Replacement of digital type step controller for Hot water boiler 300 k.w rapidcool make i/c sensor wire, power supply and display, removing defective & refixing the new complete as required.
Comfort technologies
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .