REPAIR MAINTENANCE TO ROOF FLOORING TILING CEILING JOINERY AND MISC WORK AND CEILING FAN EXHAUST FAN OTHER FANS FOR VARIOUS LOCATIONS UNDER AGE EM AND AGE BR I OF GE BENGDUBI

Amount

Supply only integral water proofing compound liquid grade conforming to IS-2645 complete all as specified and directed.

S&F 30mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) area not exc. 1.5sqm each, including cutting holes for removing the hold fast,making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) exc. 1.5 sqm and n.exc 4 sqm each, including cutting holes for removing the hold fast, making good disturbed surfaces and removing materials from site of work complete all as specified and directed.

Taking down old unserviceable shutters of any description exc 1.00 but n.exe 2.00 Sqm each complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heatm moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain/decorative colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement in the frame at site as per specification & drawing. etc complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing complete all as specified Make : Rajshree/Sintex/H2O solution. Note:-The door frame to be fixed to wall using 8 x 100 mm long anchor fasteners.

S&F Factory Made Solid PVC Moulded Door Shutter with wood free EPS , 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F Solid PVC frame (Single Rebated) of size 60mm x 30mm made out of solid PVC foam with homogenous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life) complete all as specified and directed.

S&F 100mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and direcetd.

S&F 100mm Butt hinges,medium weight, cold rolled mild steel, complete all as specified and directed.

S&F 100mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

S&F 150mm size Extruded brass handles, fabricated type polished complete all as specified and directed.

S&F 150mm size aluminium handle cast type complete all as specified and directed.

M&L for Galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe -410-W(Gde-E-250) quality-A. complete all as specified and directed.

S&F steel window with side hunge shutters including projecting type hinges with steel handle and steel peg stey, tower bolts etc. complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F steel window with side hunge shutters including projecting type hinges with steel handle and steel peg stey, tower bolts etc. complete without glazing bars dovetailed or welded complete all as specified and directed.

S&F for 1.25mm thick pressed steel frames 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,etc.complete all as specified and directed.

M&L for 1.25mm thick pressed steel door frame of size 105mm x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

M&L for anodised aluminium snap grid (SIZE-605x605MM) frame work for false ceiling complete all as specified and directed.

S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F Pre- painted coloured trapezoidal profiled Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

S&F Pre- painted coloured plain sheet Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP/ XRW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

Dismantling of floor, hearth or wall tiling / Paving Blocks including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed.

M&L for sheet glass, 4mm thick, plain ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each pane complete all as specified and directed.

M&L for 4mm thick, Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each panecomplete all as specified and directed.

Hacking out old broken glass (any thickness size quality and discription) for metal frame exc 1.5 sqm including punching, drilling out old glazing pins / spring clips and providing new ones complete all as specified and directed.

M&L for preparation of untreated new wood/wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth including preparation of surfaces complete all as specified and directed.

Demolition of cement concrete in ground floor and paving n.exc 15 cm thickness( below or above ground level) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings incl ridges, hips and valley gutter complete all as specified and directed.

Dismantling wall and ceiling board( fiber, pulp, insulation, etc.) or insulation board/slab/ blankets, any thickness, including cover fillets complete all as specified and directed.

M&L for newly plastered surface of wall appying two coat of white or tinted oil bound distemper over one coat of alkali resistant priming paint including 01mm thick wall care putty etc complete all as specified and as directed.

S&F 30mm thick 2nd class hard wood glazed and skeleton window shutter open rebated and prepared to receive glass, gause etc. with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamferred or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR part-I, Sec-08, Clause 8.24(b), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 2nd class HW rail and style 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 4 mm thick designed Non asbestos fiber cement building boards, fixed or laid /inserted to timber /GI /Aluminium frame-work with screws as in ceiling complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base of hardstanding and ramp and finishing the surface without using extra cement complete all as specified and directed.

M&L for Glazed ceramic tiles coloured 300mmx 450mm , 6 to 7 mm thick as in skirting / dado, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surface etc complete all as specified and and as directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for Non Skid ceramic tiles (coloured) 7 to 8 mm thick , (square / rectangular) area of each tiles exceeding 0.18 sqm but not exceeding 0.38sqm as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes etc complete all as specified and directed

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers 10mm +5mm in cement mortar 1:4 on external surfaces of brick work or concrete surfaces with using WPC finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured and paid separately under respective item of this schedule.

M&L for 5mm thick rendering in cement mortar 1:3 over/soffit of chajja/ceiling, finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkai registant primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying one coat of oil bound distember over a coat of primer white or any tint over 1mm thick plaster of paris complete all as specified and directed.

M&L for preparation of new undecorated surface of ceiling and applying two coats of white wash complete all as specified and directed.

M&L for identifying and rectifying day to day complaints of ceiling fan / exhaust fan / wall fan / cabin fan / pedstral fan or any type and any size fans at site on daily including taking down celiing fan / exhaust fan / Wall fan of any type / make / sweep from its location at OTM & Md accn under GE Bengdubi area, servicing of fans after removing blades, opening of fan at site and cleaning ball bearing, gun metal bush, filling grease /oil and changing of nut , screwes, check nuts, rubber reel, nut & bolts of size 15 mm to 60 mm including replacing defective condensor, ball bearing, conecting wire, gun metal bush,lock nuts, cross pin, ceiling rose etc if required and re-assembling of fan, blades, down rod, conopy etc and hanging back fan to its original location after cleaning of body, connecting to ceiling rose complete all as specified and directed. Note : (i) all spare i.e condenser, ball bearing, flexible wire, bush shall be measured and paid under relevent item. (ii) Cost of petty stores such as grease, lubricating oil, varnish, coil tie, lock nut , cross pin,check nuts,rubber seal etc are deemed to be included in quated rate. (iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate. (iv) Only replacement of fan capacitor will not be measured in the same item without taking down of fan.

Taking down carefully ceiling fan any sweep size and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades to the work shop for rewinding including cleaning and dismantling the fan into parts and segregation of unserviceable parts, replacement of unserviceable spares parts with new parts including necessary machining work and lubricating with approved grade of grease and necessary minor soldering work (if required) and re-assembling the fan, testing and refixing the fan in same position including all electrical connection and material and labour for replacement of two nos split pins, one connection block and one rubber reel all as specified and as directed. Note : (i) Rewinding work of armature shall be measured and paid separately. (ii) New spare parts required for replacing old burn out parts shall be measured and paid separately. (iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate.

Material and labour for removing burnt copper winding of ceiling fans 1200 mm sweep including necessary dismantling, cutting and removing of unsv windings, cleaning, segregation of serviceable and unsv parts including re-windings of complete fan winding with super enameled copper wire of existing gauge and weight of approved make and brand and taping, quick heat varnishing, baking, drying in heat chamber to obtain proper insulating resistance and reassembling the fans including replacement of other unsv parts and testing complete all as specified and as directed.

All as pr item No.54 above but for 1400 mm sweep ceiling fan all as specified and as directed.

Taking down carefully Exhaust fan any sweep size and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades to the work shop for rewinding including cleaning and dismantling the fan into parts and segregation of unserviceable parts, replacement of unserviceable spares parts with new parts including necessary machining work and lubricating with approved grade of grease and necessary minor soldering work (if required) and re-assembling the fan, testing and refixing the fan in same position including all electrical connection and material and labour for replacement of two nos split pins, one connection block and one rubber reel all as specified and as directed. Note : (i) Rewinding work of armature shall be measured and paid separately. (ii) New spare parts required for replacing old burn out parts shall be measured and paid separately. (iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate.

Material and labour for removing burnt copper winding of Exhaust fans upto 300 mm sweep including necessary dismantling, cutting and removing of unsv windings, cleaning, segregation of serviceable and unsv parts including re-windings of complete fan winding with super enameled copper wire of existing gauge and weight of approved make and brand and taping, quick heat varnishing, baking, drying in heat chamber to obtain proper insulating resistance and reassembling the fans including replacement of other unsv parts and testing complete all as specified and directed.

All as pr item No.57 above but for above 300 mm sweep and upto 450 mm sweep Exhaust fan all as specified and as directed.

Taking down carefully Wall mounting Fan any sweep size and any make after disconnecting the electrical connection, dismantling the blades and removing fan incl blades to the work shop for Rewinding including cleaning and dismantling the fan into parts and segregation of unserviceable parts, replacement of unserviceable spares parts with new parts including necessary machining work and lubricating with approved grade of grease and necessary minor soldering work (if required) and re-assembling the fan , testing and refixing the fan in same position including all electrical connection and material and labour for replacement of two nos split pins, one connection block and one rubber reel all as specified and as directed. Note: (i) Rewinding work of armature shall be measured and paid separately. (ii) New spare parts required for replacing old burn out parts shall be measured and paid separately. (iii) Labour cost for replacing spare parts are deemed to be inclusive in the quoted rate.

Material and labour for taking out and removing burnt copper winding of wall mounting fan of any sweep size, cleaning the armature, rewinding the fan armature for wall fan of any size with new super enamelled copper wire of existing gauge including supply and fixing necessary insulating materials etc and varnishing with approved grade of insulation varnish and heating up and testing all as specified and as directed.

Supply only bearing No. 6201/6202 for ceiling / Exhaust fan. (Make - TATA/SKF/NBC/HCH ).

Supply only bearing No.6203/6204 for ceiling / Exhaust fan. (Make - TATA/SKF/NBC/HCH ).

Supply only gun metal bush of any size for ceiling / Exhaust fan/ wall mounting fan . (Make - TATA/SKF/NBC/HCH ).

Supply only fan condensor 3.15 mfd oil filled. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply only fan condensor 3.15 mfd dry type. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply only fan condensor 2.5 mfd oil filled. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply only fan condensor 2.5 mfd dry type. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply only Exhaust fan condensor 1.5 mfd dry type. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply only mounting clamp assembly complete for ceiling fan 1200mm/1400mm sweep brass type with amp,bolt,nut,washers, safety/ split pins and rubber bush and all as specified and as directed.

Supply only down rod complete suitable for any type any size of ceiling fan complete all as specified and as directed.

Supply only PVC flexible multi stranded copper wire twin twisted two core of size 0.75 sqmm all as specified and as directed. (Make:Havells/Plaza/Polycab/KEI)

Supply and fixing in repair Polycarbonate electronic fan regulator 120 watt 240 volts socket type two module 5 step speed regulator. Make: Anchor Penta/Havells/C&S/Goldmedal.

Supply and fixing in repair Modular Regulator Step Type 120 watt, 2 module complete all as specified and directed. Make: Legrand, Model: Myrius / Anchor, Model: Woods / Schneider, Model: Opale.

Supply and fixing in repair fan condensor 2.5 mfd oil filled 240 volts for rectification of day to day fan not working complaint at site. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply and fixing in repair fan condensor 2.5 mfd dry filled 240 volts for rectification of day to day fan not working complaint at site. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply and fixing in repair fan condensor 3.15 mfd dry type 240 volts for rectification of day to day fan not working complaint at site. (Make - USHA/UNIVERSAL/Havells/Tibcon).

Supply and fixing in replacement sheet metal louvers shutters for Exhaust fan of any size upto 300 mm sweep suitable for any make made of GI sheet and fixing with fasteners etc complete all as specified and as directed.

Supply and fixing in replacement sheet metal louvers shutters for Exhaust fan of any size above 300 mm sweep suitable for any make made of GI sheet and fixing with fasteners etc complete all as specified and as directed.

S & F for in repair energy efficient exhaust fan of 300 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Make: Usha/Bajaj/Havells

S & F for in repair energy efficient exhaust fan of 380 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Make: Usha/Bajaj/Havells

S & F for in repair energy efficient exhaust fan of 230 mm sweep made of sturdy Engineering Plastic Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. Make: Usha/Bajaj/Havells

Supply and fixing in repair Wall fans complete with blades, electronic regulator and accessories, 230V,400 mm sweep. Five star rated complete all as specified and directed. Make: Bajaj/Havells/Usha

Material and labour for painting of ceiling fans complete of any sweep size and any make with one coat of first quality synthetic enamell paint of approved tint by spray including preparation of old painted surface and removing all dust, oil mark etc and filling cavaties with filler materials,and writing serial / MES number as specified (with paint of black colour with each letters/figures in Block of height n.exc 2 cm) complete all as specified and as directed.

All as per item no-83 above but for painting of exhaust fans of any sweep size with blade complete of any sweep/make all as specified and as directed.

Supply and fixing in repair aluminium based ceiling fan blade (set of 3 blade) suitable for 1200/1400 mm sweep ceiling fan with nut bolt complete all as specified and directed. Make: as per approved by GE.

Supply and fixing in repair metal exhaust fan blade (three blade set) of any sweep size exhaust fan with nut, bolts complete all as specified and directed. Make:as per approved by GE.

Supply and fixing in repair ceiling fan canopy as per existing size (set of 2 nos. upper/lower). Make :as per approved by GE.

Supply and fixing in repair ceiling fan hook made of Mild steel flat iron 4 mm thick of suitable size and any type as per existing position with suitable size nuts, bolts and washer as required for hanging ceiling fan safely complete all as specified and as directed.

Supply and fixing in replacement Exhaust fan Frame metal type of size upto 300 mm sweep as per existing shaft size suitable for any make including bolts,nuts and washer etc as required complete including taking down old unserviceable one all as directed.

Supply and fixing in replacement Exhaust fan Frame metal type of size above 300 mm and upto 450 mm sweep as per existing shaft size suitable for any make including bolts,nuts and washer etc as required complete all specified and directed.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 1,18,392.00 (refer Tender Srl Page No 29). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

GAYATRI BUIDERS (BID ID -3137118)

NABIN CONSTRUCTION AND CO. (BID ID -3137365)

GOUTAM KUMAR GHOSH (BID ID -3137227)

M/S Vaishno Constructions (BID ID -3133264)

PRADIP KUMAR BOSE (BID ID -3137195)

UNIVERSAL CONSTRUCTION (BID ID -3135882)

M/S UTTAM ENTERPRISES (BID ID -3137174)

M/S R. K. INDUSTRIES (BID ID -3133238)