Supply and Installation of furniture, allied civil and electrical work at MSCCs Office, Vengrula. Dist. Sindhudurg

Furniture Work

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part3) -1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc.Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Providing internal cement plaster 12mm. Thick in Single coats in cement mortar 1:3 with out neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Providing and applying gypsum plaster (with Gypsum material) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface (Excluding rough cast plaster) in all position including preparing and Finishing the surface scaffolding etc.complete.

Providing and applying Royal Luxury Emulsion of approved make on internal wall surface as detailed be low Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10% or waterby 15 to 20% allowing to dry for 6 to 8 hours After applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45 % or 65 to 70% by role Applying paints Royal eluxury emulsion 2nd coat with brush with water content 40 to 45 % or 65 to 70 % by roller. (With prior approval of S.E.)

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases (NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram / 15l). plaster crack should be filled by Acrylic base Crack seal / Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise on site technical reports from the concerned company technologist.

Providing and fixing Modular false ceiling of 600x600mm center to center and 13mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T2”x1½” (50mmx40mm) weighing 0.39 Kilogram/mat 60cms center center and fixed with ½”x½” (15x15mm) flanges weighing 0.19 Kilogram / m suspended on 6mm dia mild steel rod weighing 0.22 Kilogram/m, fixed on wall and beams including rounding of the edges with alluinium To f2”x1½” (50mmx40mm) weighing 0.39 Kilogram/metc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete.

Providingand Fixing Vertical Blinds of approved Make and shade of 100 mm regular fabric with powder coated aluminium channel with telting PVC chain & bottom weight plate with all necessary fixtures and fitting etc. complete. (Sample to be final by EngineerIn-charge prior execution of work)

Providing and supplying of Laminated Wooden flooring additives and requisite chemicals with installation and hardware.

Providing and fixing 34 mm thick moulded door shutter consisting of solid core single leaf flush door of 30 mm thickness lipped with 15mm (5 mm x 3) thick x 30 mm width on one style and top rail and 10 mm (5 mm x 2) thick x 30 mm width on other style and bottom rails. Theinner panels laminated with 2 mm thick termite proof, waterproof and fire resistant moulded PVC sheet with 2, 4, 6 design in different plain and / or prelim colours on one side after routing the moulded design on flush doors and 2 mm plain and / or pre lam PVC on other side using rubber adhesive on flush door and solvent cement adhesive on the PVC lipping etc. as per direction of Engineer incharge and manufacturers specification and drawing etc. complete.

Providing and fixing 3.5 to 4 mm thick Veneer finish wall Panaling made out of 50 x 25 mm (finished size) C.C.T.W. frame work or size of 600 x 600 mm center or as per site condition covered by 6 mm thick marine ply wood of the generally confiriming to I:S710-1980 finished with 3.5 to 4 mm thick matching Veneer of approved color and insatin wallnut groov matched veneer pattern and design including melamine polishing & design with antitermite treatment etc. to plywood and wood work with ten years guarantee bond etc. including alllead and lifts complete as per Architects Drawing and instructions of Engineer Incharge.

Providing & Fixing in position, Acoustical Panelling made from 12 mm wp Plywood & 1.5mm laminate on, 50 x 50 mm Sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 Gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour, finishing etc complete

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm of 8 to 10mm thickness (flooring) and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to 10mm thickness (skirting / dado) and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

Providing and fixing European type white glazed earthenware coupled closet symphonic trap with symphonic low level white glazed 10 litres cistern with black backlite seat with all necessary pipe connection etc. complete.

Providing and fixing on walls/ ceiling/ floor 15 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete

Providing and fixing on walls/ ceiling/ floor 25 mm dia. uPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and laying for 225 mm dia salt glazed S.W. pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

Providing andc onstructing Brick Masonry Inspection Chamber 90cm x 45cm With R.C.C. raft in B.C. soil area including cost of rein-forcement, 1:2:4 cement concrete channel shalf round G.S.W. pipes, Brick Masonry, plastering from inside and air tight with 75 mm thick R.C.C. cover medium duty 140 Kilogram etc. complete.

Providing & Fixing of Executive's Table @ 1800Lx900Dx750HT - TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band as per drawing

Executive Table @ 2250 L x 2100 D x 750 HT including Low Height Credestal @ 1200 L x 450 D x 650 HT Providing & Fixing of Table @ 2250L x 2100D x 750HT TOP & GABLEEND to be made of Membrane finish with soft water falledges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18mm thick Prelaminated particle board with PVC edge band. INCLUDING CREDESTAL @1200LX450DX650H:-To be made out of Membrane Finish (2 Openable Shutter & 3 Drawer Pedestal in between ) as per drawing.

Full Height Partitions in Glass finish - Providing and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized/Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from each other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing.

Providing & Fixing Curviliner Workstation @ 1500/1500Lx600/600Dx750HT, Curvilinear Table Top @ 1500/1500Lx600/600D:- TOP to be made of 25 mm thick Prelaminated particle board with PVC edge band, GABLE end to be made of 25 mm thick Prelaminated particle board with PVC edge band, KEYBOARD TRAY (WITHOUT MOUSE TRAY):- Metal Powder Coated - Black Color, CPU TROLLEY:- Metal Powder Coated - Black Color, along with 3 DRAWER PEDESTAL UNIT having overall size 392L x 450D x 680Ht. mm. with central lock and key. 3 Drawers and body are complete metal with powder coat finish, facia in 18 mm prelaminated particle board,

Conference Table @ 1800 x 900 x 750 mm Ht. Providing & Fixing of Main Table @ 1800L x 900D x 750HT - made up of 18+18mm Thick MDF top with PVC Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4mm thich is running all over the table top edge. Gable ends is Aerofoiled Shape with front edges in PVC Membrane finish and rest in Prelaminated MDF with batton structure. Gable ends should be hollow from inside for the provision of passing electrical and Data wiring. , MODESTY PANEL:- to be made of 18 mm thick Prelaminated particle board with PVC edge band Access Flap:- For Wire manager 1 No.

Full Height Steel Storage @ 750Lx450Dx2100HT Providing and fixing Openable Steel Storage of 750 x 450 x 2100Ht, with 4 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 4 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns as as per drawing.

Providing & Arrangemnt of High Back, Synchronized Mechanism with Multiple Locking, Adjustable Armrest, Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Leatherite Upholstery

Providing & Arrangemnt of MId Back, Normal Syncro Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong/Nylon Base with Leather Upholstery

Providing & Arrangemnt of Mid Back, ECO CTS Mechanism , Fixed Armrest , Gaslift for Seat height adjustment, Standard 5-prong P/Nylon Base with Fabric Upholstery

Providing and Fixing 3 seater Public seating chair made of complete metal with Legs in Crome finish and seates in silver powder coating finish.

Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms) Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat

Providing and Fixing stainless steel kitchen trolley of over all 26" height and 22" depth, supported on aluminium pipes, trolley basket made out of 5mm stainless steel rod fitted on telescopic channel of size 1.5" x 20" x 22" on both sides of trolley of 12" or above size, panel having 40 Kilogram load bearing capacity of trolley made out of 20 mm PUC coated plywood and colour combination as directed by E-I-C. Inner side of panel covered by white mica, 100 mm s.s. decorative handle. (The width and height of individual compartments shall be kept as directed by Engineer-in-charge)

Tea Table 900mm X 750mm X 450mm for m.s. ante chamber Providing And Fixing Of Tea Table 900mmX750mmX450mm With 12mm Thick Colour Eitched Tempered Glass With Bevelled Drawing Made Out Of 18mm Thick Waterproofing Ply. The Outer Laces To Be Finished With High Quality 4 Mm Thik Veneer Or 1 Mm Thik Mica Etc.

Providing plastic chair (Nilkamal Brand) as shown in the drawing

Providing and supplying corner table of required size with top made of 8mm thick bevelled glass and under structure made of 18mm thick Marine ply (IS 710 : 2010) with all exposed edge are finished with 2mm thick machine pressed PVC edge banding in matching colour. (Rehau Make/or Equivalent) for better impact resistance etc. complete. Nylon button stopper to hold glass top in position, Nylon bushers etc. complete.

Providing and Supplying Reception table of overall size 1650 X 750 X 750 mm made out of 19 mm thick Marine ply (IS 710 : 2010) top Sides and apron having Top and bottom horizontal patta. The table shall be externally and internally finished with 4mm thick group match veneer pattern with grooves including necessary lipping moudling and hardware.5 mm thick thoughened glass modesty shall be provided with 50 X 30 mm BTC wood frame etc. complete. Antitermite treatement to marine ply and all wooden accessories on both sides for full faces before the joineries melamine polish on french polish base coat, hardware as per drawings. etc. all complete as per Architects Drawing.

Decorative Plants

Providing and fixing decorative High Oxygen Indoor Plant Syghonium Plant

Providing and fixing decorative lucky bamboo plant in a round glass planter

Providing and fixing Alkaline Green Ficus Benjamina Marginata Indoor Plant

Electrical Work

Supply, installation, testing & commissioning of 4MP IP Dome/Bullet Camera 1/3" CMOS image sensor, Output 4mp (2560X1440) @25/30fps, Max.H265 codec high compression ration, Buit-in IR LED, max IR distance: 30m, H.264 MJPEG, WDR-120dB, SD card slot, Support max.256 GB micro SD card, IP67 protection, Steams capacity 2, Protection IP67, CE,ROHS.

Supplying, installing, testing & commissioning of 32/40 Ch. Network Video Recorder (NVR), suitable connect Min. 32 IP Cameras, up to 5 Megapixel Resolution, with HDMI /VGA outputs, provided HDMI output of 4K resolution or VGA output with output up to 1920 × 1080.Support H.265 or higher, H.264, MJPEG, Incoming Bandwidth 250Mbps with minimum 4 SATA Hard Disks, ANR Technology,4 SATA interfaces for 4 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps self adaptive Ethernet interface, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specification no. CCTV-NVR

Supplying & erecting 43" professional LED display with 1920*1080 (Full HD) Display, suitable for 16/32 channel NVR and following features Brightness: minimum 500 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In, Built-in speakers maximum 10 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON

SITC for Interactive Panel with Google Integration : Size 86", Display Area (in) 74.6 x 41.9 in, Resolution 4K UHD, Touch Technology IR, Touch Points Up to 40, Viewing Angle 178°, Embedded Operating System Android 14 (Upgradable via future firmware), RAM 8GB, VESA Mount Pattern 800x400mm, Google EDLA Certified, USB Type-C with 65W Power, Better Connectivity with Wi-Fi 6, Embedded 20W Speakers, Compatible with All Devices, Backlight LED, Glass Surface Technology Anti-Glare+Anti-Fingerprint + Antimicrobial Tempered Glass, Speaker Position Bottom Front.

SITC for OPS with Core i5, 4K, 12 Gen, 8 GB Ram, 512 SSD, Windows 10/11 Trail Version Preloaded with Graphic Card.

Interactive Flat Panel Display Heavy Duty Trolley Cart for 86 Inch display with Video Conferencing hoist platform.

SITC for Wireless presentation system, Operating system Linux, Output resolution 2160p60/30, 1080p FHD 60/30, 720p60, Supported devices for wireless mirroring (up to 4K depending on device) iOS, iPadOS, Android, Windows, macOS, Chrome OS, Supported wireless mirroring protocols AirPlay, Miracast (Peer-to-Peer and MICE), Chromecast, vSolution Cast, Supported Software & Apps vSolution App, vSolution Link Pro, Max. no. of devices simultaneously displaying material on-screen 4, Support for touchscreen displays Yes, Touchback control for Windows Yes, Dynamic on-screen content arrangement Yes, Video outputs 1x HDMI, Audio Via HDMI Out, USB Out, USB ports Front: 1x USB 3.0, 1x USB 2.0, Wifi standards (wifi 5) 2.4 GHz in Access Point Mode / 2.4 and 5 GHz in Infrastructure Mode, LAN ports Yes, 1x1GigE.

SITC for All-in-One Video Collaboration Bar for Medium to Large Rooms, Operating System Android 13, Camera Maximum pixels: 3*50MP pixels, Number of preset positions: 9, Electronic gimbal, 1x Wide HFOV 98°, VFOV 81° ; 2x Tele HFOV 41.6° VFOV 31.8°, 8x digital zoom, Maximum resolution: 4K, Privacy cover: Electric lens cap, Lens calibration, Intelligence Features IntelliFocus, Auto Framing, Speaker Tracking, People counting, Picture in Picture, Number of cameras: 3, Speaker Built-in 4 x 5W speakers, Microphone Built-in 16 MEMS microphone array, 10-meter pickup distance, Ports 1x USB3.0 Type-A port, 1x USB3.0 Type-B port, 1x USB2.0 Type-C port(for dongle pairing), 1x Ethernet port, 2x VCH port (RJ-45), 1x 3.5mm Line-in & Line-out port, 2x HDMI-out.

Supplying, erecting, testing & commissioning of 1 kVA capacity on line pure sine wave,PWM,IGBT based UPS with 0.8 to unity output pf , single phase input & 1 phase output complete with all protections as per specification no. APUPS (Without batteries)

Supplying and erecting 12 V/80Ah to 88 Ah Tubular battery with battery terminal wire, duly charged complete with 36 months warranty complete

Supplying, installing, testing & commisioning of 6000 GB Hard Disk for video survelliance equivalent to western digital.

Supplying, fixing, and configuring 8-ports 1 GE un-managed gigabit PoE switch compliant with IEEE 802.3 standards, min. 120W PoE capacity with 2GE SFP uplink erected in provided rack complete.

Supply, Installation, Testing UTP Connector (RJ-45) as per specification No.WG-NAS/UTPC.

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500 mm) as per specification No. WG-NAS/RAK

Supplying and installing FR PVC sheathed HDPE insulated copper cat-6 cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

Supplying and erecting 6 fibers LSZH armoured multimode optical fiber cable with, core dia 50/125 µm (OM3), suitable upto 10 GBPS, compliant to IEC 60793/IEC 60794 standards, on wall/ceiling or laid in provided pipe/trench as per specification no. WG-ELVC/OFC

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Supplying and erecting exhaust fan heavy duty 230 V, A.C. 50 cycles 375/380 mm. 900 RPM complete erected in position as per specification no. FG-FN/EXF

Supplying and erecting Energy Saving Ceiling fan of 3 star rating as per BEE 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Water Purifier (RO+UV+UF)

Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230 V single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200)

Air Conditioners (AC)

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.0TR to 1.2TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC

Point Wiring

Point wiring in for light/fan/bell in 20 mm metal conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire,flush type switch, earthing and required accessories as per specification no. WG-PW/SW

Wiring for plug on board with switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification no. WGPW/ CW

Modular switches and Accessories

Supplying and erecting modular type two way switch 6A/10A (2 module) on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16/20 A with indicator on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch one way 16/20 A on provided plate and box with wiring connections complete with neon indicator.

Supplying and erecting modular type 32A, DP key tag switch with key tag on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6/16A multi socket with safety shutter on provided plate and box with wiring connections complete.

Supplying and erecting modular type T.V. socket single outlet on provided plate and box with wiring connections complete.

Supplying and erecting modular type telephone socket one gang with safety shutter on provided plate and box with wiring connections complete.

Supplying and erecting modular type (two module) electronic step regulator for fan, on provided plate and box with wiring connections complete.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly flushed to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Indoor LED Fittings

Supplying and erecting LED square / circular Max. 14 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1500 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Supplying and erecting LED square / circular Max. 18 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED.

Lamps and Tubes for Indoor & Outdoor

Supplying & erecting 14W, 230V integral type LED Lamp suitable for B-22/E- 27 base as per specification no. FG-LP.

Supplying & erecting ready to use Retrofit T8 LED, 18 / 20 watt tube light with polycarbonate body, heat sink, integrated HF electronic driver complete & compatible to T8 / T12 LED luminaire by disconnecting starter & ballast if necessary as per specification No. FG-LP/RET.

Bunch of Wires

Supplying & erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no. WG-MA/BW

Supplying & erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places. as per specification no. WG-MA/BW

Supplying & erecting mains with 2x10 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no. WG-MA/BW

Supplying & erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/bus bars or any other places as per specification no. WG-MA/BW

Fire Extinguishers

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Public Address Systems

Supplying, erecting, testing and commissioning Conference Systems Delegate Unit with adjustable gooseneck microphone having minimum length (excluding pedestal) of 18.5' (470 mm) 7.5 mV/Pa, current consumption <50mA max, mic auto switch off time 75 seconds, input - line, output - line, headphone, speaker - max input 300 mW, Controls - talk switch, speaker, volume control, headphone volume control, with accessories such as foam windshield, 2.5m interconnecting cables complete as per specification no. PA-CSDU

Supplyig erecting, testing and commissioning Conference Controller Unit controlles up to 50 disscusion units with 50W PA Amplifier with robust metal case, Line o/p - 17.5V DC/3A Max.; -34dBV (20mV), minimum 2 or more inputs, Headphone output, 60-14000 Hz frequency response, S/N ratio >60dB, Speaker output 4Ω, 8Ω/(Low Impedence) and 70V & 100V/(High Impedence) Digital recorder with LED indication bar, can playback the pre-recorded messages, suitable for 230V AC & 24V DC, on provided 19" rack. Unit shall have the facility of feeding two independent groups of Delegate Units complete as per specification no. PA-CCU