Strengthening of existing fisheries infrastructure in SKUAST Jammu

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering. All work upto plinth level.

1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size) (using 30 % boulders including cost and carriage of boulders)

1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement- All work upto plinth level.

1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness). Including attached pillasters, buttresses, plinth and string courses fillets columns, pillers, piers, abutments, posts and struts etc. upto floor 5 level exclusing cost of centring shuttering, finishing and reinforcement.

1:1.5:3 (I cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size)

Centring and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bresumers and cantilevers.

Stairs, (excluding landings) except spiral-staircases.

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Weather shade, Chajjas, corbels etc., including edges.

Columns, pillars, piers, Abutments, posts and struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

Thermo-Mechanically Treated bars of grade Fe-500 D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Honey-comb brick work 10/11.4 cm thick with common burnt clay bricks of class designation 7.5 in super structure above plinth level upto floor V level with cement mortar 1:3 (1 cement : 3 coarse sand).

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge.

Second class teak wood

35 mm thick shutters

Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws:

35 mm thick shutters.

with ISI marked M.S. pressed butt hinges bright finished of required size - Second class teak wood

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium casement stays ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Using flats 30x6mm for diagonal braces and central cross piece

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying Ceramic glazed floor tiles of size 300x300 mm(thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08%and conforming to IS: 15622, of approved brand & manufacturer in all colours and shade in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints(Payment for grouting of joints to be made separately).

Size of Tile 600x600 mm

Painting top of roofs with bitumen of approved quality @ 17 kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete :

With residual type petroleum bitumen of grade VG - 10

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat :

With common burnt clay F.P.S.(non modular) brick tile of class designation 10.

Providing gola 75x75mm in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1:3(1 cement : 3 fine sand) as per standard design

In 75x75mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400 micron, finished with 12mm cement plaster 1:3 (1 cement :3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:6 (1 cement: 6 fine sand)

6 mm cement plaster of mix :

1:3 (1 cement: 3 fine sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

New work (two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with water proofing cement paint of required shade :

New work (Two or more coats applied @ 3.84 kg/10 sqm).

Applying priming coat :

With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:

Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Supplying and stacking at site.

63 mm to 45 mm size stone aggregate.

53 mm to 22.4 mm size stone aggregate.

Stone screening 11.2 mm nominal size (Type B).

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening / binding material to fill up interstices of coarse aggregate, watering and compacting to the required density

Providing and fixing B.A. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. Made of B.A. wire of dia 4 mm.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 25x25 mm made of G.I. wire of dia 3 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge.

Supplying and stacking of hard stone (for stone pitching) 22.5 cm thick at site.

Providing and fixing water closet squatting pan (Indian type W.C pan) with 100mm sand cast iron P or S trap, 10 litre low level white P.V.c flusing cistern with manually controlled device (handle level) conforming to IS : 7231, Parryware/ Hindware / Seabird/ Orient (coral) with all fittings and fixtures complete including cutting and making good the walls and floors wherever required

White vitreous china Orissa pattern W.C pan of size 580x440mm with integral type foot rests.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing Stainless Steel A Isis 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board

610x510 mm bowl depth 200 mm.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Semi rigid pipe

40 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :

Rectangular shape 453x357 mm

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

15 mm nominal bore

20 mm nominal bore

Providing and fixing uplasticised UPVC connection pipe with brass unions :

45 cm length

15 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931:

15 mm nominal bore.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.

15 mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore

15mm nominal bore

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing high impact Polypropylene reinforced cement 6mm thick corrugated sheets (as per IS: 14871) roofing up to any pitch and fixing with polymer coated J, or L hooks, bolts and nuts 8mm dia. G.I. plain and bitumen washers or with self drilling fastener and EPDM washers etc. complete (excluding the cost of purlins, rafters and trusses), including cutting sheets to size and shape wherever required.

Providing and fixing ridges and hips in fibre cement high impact polypropylene reinforced roofing with suitable fixing accessories or self drilling fastener and EPDM washer etc. complete.

Corrugated serrated adjustable ridges

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix :

1:3 (1 cement: 3 fine sand)

Providing and laying river bed material comprising of sand , stone boulders, earth etc. complete including consolidation, watering, carriages, loading and unloading etc

Providing & fixing G.I. pipes complete with G.I. fittings.

40 mm dia nominal bore

80 mm dia nominal bore

25 mm dia nominal bore

Providing & fixing gate valve with C.I. of approved quality (screwed end)

20 mm dia nominal bore

40 mm nominal bore

Making connection of G.I. distribution branch with G.I, main of following sizes by providing & fixing tee including threading complete item.

25 mm to 40 mm nominal bore

Providing & fixing Nozzle

Providing and laying PVC pipes for inlet outlet facults.

Providing & fixing showering system in bend including all accessories complete item.

Making bund embankment in layers around the excavated pond and compacting the earth layer including watering complete item.

Providing & fixing PVC pipe:-

75 mm dia

100 mm dia

Floor trap (3")

Floor trap (4")

Grating (4")

Providing and laying of 25 mm thick open graded premix carpet (compacted) with specified graded stone aggregates for wearing course including loading of aggregates with FE loader and hot mixing of bitumen with filler and stone aggregates in hot mix plant, transporting the mixed material by tippers to paver at site of work and laying the mixed material with mechanical paver finisher to the required level and grade, rolling with power road roller to achieve the desired density and compaction including cost of priming coat/tack coat and seal coat, dressing of berms including cutting/filling with RBM up to 1 m width and 15 cm depth on both sides of the road surface including disposal of mulba to proper specified place including rolling with road roller and compacting (complete job) (Bitumen used shall be VG-30 and grading of mix sahll be as per the relevant clause of MORT & H) all complete including cost of bitumen and all sort of taxes.

Construction/Installation of shallow tubewell including all the accessories by way of providing and fixing the following items (water supply item) with necessary nuts, bolts, screws etc.

G.I. pipe 3"

G.I. socket 3"

Filter 4'-0"

C.I. valve 4"

C.I. bend 4"

Pin 3" (welded)

G.I. Bend 3"

Threading

Tee G.I, 3"x3"

Gate valve 3" (Brass)

Providing and fixing of the following electrical items and completer items.

5 H.P. motor (Make: Crompton, Kirloskar)

Starter

Service line ( 3 core wire) (16 mm2 ). AV 50 meters wire both sides.

Flanges

Rubber

Boring (4" bore, 3" delivery)

Supply & fixing of 5 HP 3 phase mono block pump set complete with all accessories etc.

Supply & fixing of outdoor type LT panel board complete with bus bar, 32 ampere TPN, motor starter, contactor, relay, single phase preventor complete with connection testing etc. as reqd.

Supplying/laying of 16 sqmm x 4.0 core aluminium armoured XLPF power cable suitable for 1.1 kv grade with earth, cost of end termination, saddle etc.

Earthing with G.I. earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (with charcoal or coke and salt) complete as required for earthing and lightning protection.

Providing and fixing 25 mm x 5mm GI strip in 40 mm dia G.I. pipe from earth electrode as required

SUB-DISTRIBUTION BOARDS

Providing and fixing 6 amps to 32 amps rating 240 volts, 'L' series, miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as reqired (category B)

Single Pole - 6 to 32 A

Supply and fixing of following rating, 2P 230 volts, SPN in the existing MCB DB complete with connections, testing and commissiong etc. as required

40 amps SPN

63 amps SPN

DISTRIBUTION BOARD

Supply, installation, testing at works, installation and commissioning of following distribution boards totally enclosed compartmentalized, cubicle indoor type fabricated with 16 SWG sheet steel, with Aluminium bus bars (both for main and neutral bus bars), complete with following switchgear/ mountings cable terminations, inter-connections as required, for 415 volts, 3 phase, 4 wire 50 HZ AC supply as per specifications and drawings.

Moulded case circuit Breakers shall be thermal magnetic trip type. Fault level for all MCCB and bus bar shall be 35 KA. ICU shall be equal to ICS=100%

All metering current transformers shall be Class 1, 15 VA.

MDB-1 (Indoor Type)

Incomer

160 A 4P MCCB – 1No.

R,Y,B phase indicating lights with control fuses - 1 set

Bus Bar

200A 415V, 50Hz, 3ph, 4 wire Aluminium Bus bar

Outgoing

40 Amp 2P SPN - 5No.

63 Amp 2P SPN - 5 No.

63 Amp 2P TPN - 5 No.

LT CABLES

Supply and laying of PVC Power cable 1.1 KV Grade armoured aluminium XLPE cables including earth work, cost of end termination, thimbles and saddles etc. as required.

3.5C x 120 sq.mm

SUB-DISTRIBUTION BOARDS

Supply and fixing of the following way, single pole and neutral / three pole and neutral, sheet steel, double door, phase segregation type, MCB distribution board, 230V / 415V on surface/recess, complete with tinned copper bus bar, neutral bus bar and link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing, etc., as required.

8 way TPN

4 way TPN

Supply and fixing 1x20 watt box type fitting complete with extruded alulminium tube rod including connection testing etc. as reqd. (CAT No. DMLNLT8-16 and LTT8-20)

Supply and fixing of 18 Watt LED Panel surface mounted including connection testing etc as reqd. (CAT No. LCDSPLN-R-18-CDL)

Supply and fixing of 9 Watt LED mirror light 2' long including connection testing etc as reqd. (CAT No. LCTL-09-CDL)

Supply and fixing of 70 Watt LED street light with GI pipe bracket with all accessories including connection testing.

Wiring for telephone point with 0.61 mm dia copper conductor unarmoured shielded twisted telephone wire in 25mm dia existing PVC conduit, connections etc. complete as required as per specification and drawings.

Supply and fixing telephone socket outlet housed in zinc passivated box with suitable connector strip in recessed wall / partitions as required

WIRING

Wiring for light / fan / exhaust fan / call bell point with 1.5 Sq mm FR PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit(2mm thick) including concealed box 6 inch and providing 5 amp switch and earthing complete as required.

Light point on board with copper wiring in ISI marked PVC conduit wiring for 3 Pin 6 amp plug point with 1.5sqmm PVC insulated multistrand copper conductor cable including P/F of 3 Pin 6 amp socket outlet on switch board in surfaced recessed PVC conduit wiring system and 6 amp switch, earth the 3 pin as required with 01 No. PVIC insulated green colour wire.

Wiring for light plug with 2 x 2.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x 2.5 mm copper wire for loop earthing required

Wiring for power plug with 2 x 4 sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x4.0 Sq mm copper wire for loop earthing as required

Wiring for power plug with 2 x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x1.5 Sq mm copper wire for loop earthing as required

Wiring for 1x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked in the existing PVC conduit etc. as required ( Invertor wiring )

Wiring for sub main wiring with following sizes of PVC/ insulated copper conductor wires in the surface/ recessed PVC / MS conduit along with PVC insulated copper conductor earth wire as required complete with connections, testing and commissioning etc. as per specifications and drawings.

2x6 sq mm with 1x6.0sqmm earth wire

2x10sq. mm with 1 x 6.0sq. mm earth wire

Wiring for sub main wiring with 4x6 sqmm alongwith 2x6sqmm earth wire sizes of PVC/ insulated copper conductor side core conductor in surface/recessed PVC conduit etc. as reqd.

Wiring for twin control light point with 2x1.5 sq. mm PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit with 2 way 6 Amp switch

Supplying and fixing metal box of 180 x 100 x60mm deep in recessed with suitable size phoenolic laminated sheet cover in the front including providing and fixing 3 pin 15Amp socket outlet and 15Amp switch connections, painting etc. as required. (Power plug)

Supply and fixing of 250 mm x 300 mm x 100 mm deep size metal box with suitable size phenolic laminated sheet cover in the front including connection testing etc as reqd.

Supply and fixing of 200 mm x 300 mm x 100 mm deep size metal box with suitable size phenolic laminated sheet cover in the front including connection testing etc as reqd.

Supply and fixing step up electronic fan regulator on the existing switch box including connecting testing etc. as required.

Supply & fixing of 10 sqmm x 2 core aluminium armoured PVC cable suitable for 1.1 KV grade including cost of end termination, connection testing etc. as reqd.

Supplying and fixing of exhaust fan 300mm sweep heavy duty trans air with double ball bearing including connection, texting etc. as required.

Supply and fixing Call bell / buzzer DC / AC single phase 230 V complete

Supply and fixing 20 Amp Industrial socket with 32 Amp SPN including connection, testing, etc. as required

Supply and fixing of 25 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and fixing of 32 mm dia PVC conduit alongwith accessories in surface/recess.

Sushil Kumar

Narinder Gupta

KULDEEP SINGH