SOPD_G_20_21_148 1) Improvement of road from Madhapara Puthimari road at Simuluguri to Jukuta (L900.00 m), (2) Improvement of road from Lutumari Bazar to Bakulaguri road including widening and side drain (Ch. 0.00 to 3000.00 m), (3) Construction of

Amount

Clearing and grubbing of road land including uprooting wild vegetation ,grass ,bushes ,shurbs ,sapling and trees of girth up to 300 mm ,removal of stumps of such trees cut earlier and diposal of unservicible material and stacking of servicible material to be used or auctioned ,up to a lead of 1000 m as per Technical Specification Clause 201. (I) By Manual means (A) In area of Non-thorny jungles

Dressing & profiling the existing WBM/Granular/Earthen surface layer of the road from edge to edge of the existing carriage way and both the shoulders, filling low spots and ravelled stretches by providing additional materials of same type as that of the existing top surface layer, cambering, watering, rolling with 8-10 tonne roller to obtain specified compaction, etc to obtain a uniform formation surface with cross fall from the road centre line to the outer edges of the existing embankment. Works to be carried out in accordance with MORT&H specifivation section 300 and as directed by the deptt. (rate considered as per SOR for road bridge and culvert works for all divisions inder PWD Assam 2009-10, at sections where the top level of the subgrade of the existing road surface is not proposed to be raised by more than 100mm. I) Roads having hard crust a) Carriage way

Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporating to site, spreading, grading to required slope and compacting to meet required of table 300.2 (including compansation of earth) (i) Private land.

Removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground supporting embankment subgrade replacement by suitable soil, which shall be paid separately as per Clause 303.5.2 as per Technical Specification Clause 302.3.11

Supplying and laying of Polypropylene extruded Geogrid with a minimum stiffness (modulus) at 0.5% strain according to ISO 10319 should be 350x550 Kn/m with apparaent coefficient of friction soil/geosynthetics accroding to EN 13738 must be atleast 1.70(us/gsy) at 10 KPa load and with a min transversal rib thickness of 2.5 mm and longitudinal rib thickness of 3.6 mm. Aperture of geogrid should be 30mm x 30 mm. Geogrid should not be made of bonding of strands or punching and stretched sheets

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Water Bound Macadam:- Using stone screening Type-B 11.2 mm for Gr.II Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading-2 as per Technical Specification Clause 405. (A) By Manual Means

Water Bound Macadam:- Using stone screening Type-B 11.2 mm for Gr.III Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading-3 as per Technical Specification Clause 405. (A) By Manual Means

Inter locking concrete Block pavement :: (i) Providing and laying interlocking concrete block pavement(M40) having thickness 80mm as per technical specification clause 1504(inclusive of Edge restraint and carriage)

Prime Coat (I) Low porosity Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Tack Coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.30 to 0.35 kg per sqm on the prepared non-bituminous surfaces (cement concrete pavement) cleaned with Hydraulic broom as per Technical Specification Clause 503.

Semi - Dense Bituminous Concrete (Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5% of mix and filler transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the reqd. grade, lavel and alignment,rolling with smooth wheeled,vibratory and tandem rollers to achieve the desired compaction as per MoSRT&H cl. no.508. complete in all respect. (I) with 60/70 or VG-30 grade bitumen (ii) for GradingII(10 mm nominal size)

Providing and fixing of typical informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 Size 1.60m x 1.20 m

Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications

Providing reflective pavement marker with a provision of spike at the bottom with Micro prismatic lens in both direction having thermoplastic body adhering to the specification and guidelines of MoSRTH & H's fixed to the road surface using the adhesives and the procedures recommended by the manufacturers with three months replacement warranty and free maintenance.

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 (ii) Ordinary Kilometer Stone (precast)

Traffic Sign:: Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting 2mm thick with area not exceeding 0.9 sqm supported on a mild steel single iron post 75mmx75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450x450x600mm, 600mm below ground level as per approved drawing and tecnical specification Clause 1701.(iv) 800mm x 600mm rectangular

Traffic Sign:: Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting 2mm thick with area not exceeding 0.9 sqm supported on a mild steel single iron post 75mmx75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450x450x600mm, 600mm below ground level as per approved drawing and tecnical specification Clause 1701. (ii) 60 cm equilateral traingle

Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for three year.

Double HP Culvert: Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling course below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Bedding for pipe (ii) Type B(First Class) Bedding Laying (First Class) bedding on well compacted sand moorum as per Clause 1105(ii) (i) Sand Filling

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. II. In 1:4 cement mortar

Stone masonry work in cement mortar in sub structure complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203. II. In 1:4 cement mortar

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in double row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. (A) 1000 mm dia

Earth work in excavation of foundation of structures as per drawing & technical specifications clause 305.1 including setting out construction of shoring and bracing, removal of strumps and other deleterious material and disposal upto a lead of 50m ,dressing of sides and backfilling in trenches with excavated suitable material. (1) In ordinary soil , A. Manual means. i)Upto 3m Depth.

Providing brick soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. a) Brick on flat soling

Plain/reinforced concrete in open foundation complete as per drawing and technical specification Clause 802,803,1202 &1203. (i) PCC Grade M-15

Supplying,fitting and placing TMT bar reinforcement bars in sub structures complete as per drawing and technical specificatios.

Plain /reinforced cement concrete in Sub Structure complete as per drawing and technical specification and steel shuterring framework. B) RCC Grade M-25 Height upto 5.00M

Providing Weep holes in Brick Masonry/Plain/Reinforced Concrete abutment,wingwall/return wall with 100mm dia AC Pipe,extending through the full width of the structure with slope of 1V :20H towards drawing foce.Complete as per drawing and technical specification.

Madhapara-Puthimari Road at Simuluguri to Jukuta Clearing and grubbing of road land including uprooting wild vegetation ,grass ,bushes ,shurbs ,sapling and trees of girth up to 300 mm ,removal of stumps of such trees cut earlier and diposal of unservicible material and stacking of servicible material to be used or auctioned ,up to a lead of 1000 m as per Technical Specification Clause 201. (I) By Manual means (A) In area of Non-thorny jungles

Dressing & profiling the existing WBM/Granular/Earthen surface layer of the road from edge to edge of the existing carriage way and both the shoulders, filling low spots and ravelled stretches by providing additional materials of same type as that of the existing top surface layer, cambering, watering, rolling with 8-10 tonne roller to obtain specified compaction, etc to obtain a uniform formation surface with cross fall from the road centre line to the outer edges of the existing embankment. Works to be carried out in accordance with MORT&H specifivation section 300 and as directed by the deptt. (rate considered as per SOR for road bridge and culvert works for all divisions inder PWD Assam 2009-10, at sections where the top level of the subgrade of the existing road surface is not proposed to be raised by more than 100mm.I) Roads having hard crust a) Carriage way

Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporating to site, spreading, grading to required slope and compacting to meet required of table 300.2 (including compansation of earth) (i) Private land.

Removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground supporting embankment subgrade replacement by suitable soil, which shall be paid separately as per Clause 303.5.2 as per Technical Specification Clause 302.3.11

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Water Bound Macadam:- Using stone screening Type-B 11.2 mm for Gr.II Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading-2 as per Technical Specification Clause 405. (A) By Manual Means

Water Bound Macadam:- Using stone screening Type-B 11.2 mm for Gr.III Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading-3 as per Technical Specification Clause 405. (A) By Manual Means

Inter locking concrete Block pavement :: (i) Providing and laying interlocking concrete block pavement(M40) having thickness 80mm as per technical specification clause 1504(inclusive of Edge restraint and carriage)

Providing and fixing of typical informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 Size 1.60m x 1.20 m

Traffic Sign:: Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting 2mm thick with area not exceeding 0.9 sqm supported on a mild steel single iron post 75mmx75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450x450x600mm, 600mm below ground level as per approved drawing and tecnical specification Clause 1701.(iv) 800mm x 600mm rectangular

Traffic Sign:: Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting 2mm thick with area not exceeding 0.9 sqm supported on a mild steel single iron post 75mmx75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450x450x600mm, 600mm below ground level as per approved drawing and tecnical specification Clause 1701 (ii) 60 cm equilateral traingle

Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for three year.

Chitalmari PMGSY Road to Rengkhang Gaon Clearing and grubbing of road land including uprooting wild vegetation ,grass ,bushes ,shurbs ,sapling and trees of girth up to 300 mm ,removal of stumps of such trees cut earlier and diposal of unservicible material and stacking of servicible material to be used or auctioned ,up to a lead of 1000 m as per Technical Specification Clause 201. (I) By Manual means (A) In area of Non-thorny jungles

Construction of embankment with aproved materials obtained from borrow pits, Construction of embankment with approved materials obtained from borrow pits with all lifts & leads .transporting to site, spreading grading to required slope and compacting to meet required of Tables 300.2 (including compansation of earth)(a) Private land.

Construction of sub-grade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporating to site, spreading, grading to required slope and compacting to meet required of table 300.2 (including compansation of earth) (i) Private land.

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Water Bound Macadam:- Using stone screening Type-B 11.2 mm for Gr.III Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading-3 as per Technical Specification Clause 405. (A) By Manual Means

Inter locking concrete Block pavement :: (i) Providing and laying interlocking concrete block pavement(M40) having thickness 80mm as per technical specification clause 1504(inclusive of Edge restraint and carriage)

Providing and fixing of typical informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 Size 1.60m x 1.20 m

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 (ii) Ordinary Kilometer Stone (precast)

Kilometre Stone Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc as per drawing and Technical Specification Clause 1703 (ii) Ordinary Kilometer Stone (precast) (iii) 200M Stone (precast)

Traffic Sign:: Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting 2mm thick with area not exceeding 0.9 sqm supported on a mild steel single iron post 75mmx75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450x450x600mm, 600mm below ground level as per approved drawing and tecnical specification Clause 1701.(iv) 800mm x 600mm rectangular

Traffic Sign:: Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting 2mm thick with area not exceeding 0.9 sqm supported on a mild steel single iron post 75mmx75mm x 6mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450x450x600mm, 600mm below ground level as per approved drawing and tecnical specification Clause 1701 (ii) 60 cm equilateral traingle

Planting of Trees and their Maintenance for three Year (Planting of trees by the road side (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground, mixing the soil with decayed farm yard/sludge mannure, planting the saplings, backfilling the trenches, watering , fixing the tree guatrd and maintaining the plants for three year.

Earth work in excavation of foundation of structures as per drawing and technical specifications clause 305.1 including setting out,construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m dressing of side.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawing and Technical specifications Clause 802, 803, 1202, & 1203.(PCC Grade M-15) (I) Nominal Mix

Bedding of Pipe Laying (First class) bedding on well compactad sand, moorum or approved granular material as per clause 1105(ii) Type B (First Class) Bedding

Providing & Laying Reinforced Cement Concrete Pipe NP3 for culverts on first class bedding of Granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonary work. 1000mm dia

Brick masonary work in Cement mortar 1:3 in foundation complete excluding pointing and plastering, as per drawing and technical specifications clauses 600, 1202 & 1203

Plastering with cement mortar (1:3), 15mm thick on brick work in sub-structure as per Technical specification.

Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25kg laid dry complete as per drawing and technical specifications Clause 1301

Providing and laying pitching on slopes laid over prepared filter material as per drawing and technical specifications Clause 1302

Providing and laying filter material underneath pitching in slopes complete as per drawing and technical specifications Clause 1302

GUNJ ASSOCIATES