Interior and Renovation Work for the office of SIDBI, Patna, Bihar

Name of Work : Interior and Renovation Work for the office of SIDBI at PATNA

DETAILED SUMMARY

S.No. Sub-Head NDSR Amount (in Rs.)

1 Civil & Interior Works 7,02,385.48 29,40,425.95

2 Electrical/FA/PA 7,41,701.00 3,05,108.57

4 CCTV AND NETWORK 0.00 2,36,950.00

5 Furniture Work 0.00 24,53,720.00

7 Add GST Multiplying factor of 1.0633 24,70,531.27

8 TOTAL i/c GST 85,34,210.00

Digitally signed by AMIT

Civil & Interior Works

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

CIVIL AND INTERIOR

1 PARTITIONS AND WALL CLADDING - -

WALL PANELING :-Providing and fixing Paneling upto ceiling height consisting of

Aluminium frame and required board, frame work made of Aluminium section

made of 50x25 mm , consisting of floor and ceiling channel 50mm wide having

equal flanges of 25 mm and 0.50 mm thick, fixed to the floor and ceiling at the

spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50

mm length or suitable anchor fastener or metal screws with nylon plugs and the

studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50

mm thick fixed vertically within flanges of floor and ceiling channel and placed

at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including

fixing of studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on

1.1 MR studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The - -

boards are to be fixed to the frame work with joints staggered to avoid through

cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of

9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the

studs using metal to metal flat head screws, including jointing and finishing to a

flush finish with recommended jointing compound, jointing tape, angle beads at

corners (25 mm x 25 mm x 0.5 mm), joint finisher as per manufacture's

specification and direction of engineer in charge all complete.(Cost of

Aluminium framing 600X600mm Paid saperately)

Paneling with 12 mm thick HDHMR board to IS: 5509

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

WALL PARTITION-Providing and fixing partition upto ceiling height consisting of

Aluminium frame and required board, frame work made of Aluminium section

made of 50x25 mm , consisting of floor and ceiling channel 50mm wide having

equal flanges of 25 mm and 0.50 mm thick, fixed to the floor and ceiling at the

spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50

mm length or suitable anchor fastener or metal screws with nylon plugs and the

studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50

mm thick fixed vertically within flanges of floor and ceiling channel and placed

at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including

fixing of studs along both ends of partition fixed flush to wall with suitable anchor

fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre,

and fixing of boards to both side of frame work by 25 mm long dry wall screws on

1.2 MR studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The - -

boards are to be fixed to the frame work with joints staggered to avoid through

cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of

9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the

studs using metal to metal flat head screws, including jointing and finishing to a

flush finish with recommended jointing compound, jointing tape, angle beads at

corners (25 mm x 25 mm x 0.5 mm), joint finisher as per manufacture's

specification and direction of engineer in charge all complete.(Cost of

Aluminium framing 600X600mm Paid saperately)

Both side 12 mm thick HDHMR board to IS: 5509 SQM 3,850.00 100.00 3,85,000.00

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain

in gloss / matt/ suede finish with high density protective surface layer and reverse

1.3 9.127 side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of - -

adhesive of approved quality.

Providing and fixing framed Toughened glass door/glass partition wherever

required 12 mm thickness including all fittings, frames etc. as per direction of EIC(

Floor spring lock and handle paid seprately)

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

1.5 9.1 fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for - -

9.1.1 Second class teak wood cum 1,31,576.95 0.50 65,788.48

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock wool

conforming to IS: 8183, having density 48 kg/m3,50 mm thick,wrapped in 200 G

1.6 12.62 Virgin Polythene Bags fixed to wall wirh screw, rawel plug & washers and held SQM 277.90 90.00 25,011.00

and in position by criss cossing GI wire etc. complete as per directions of Engineer-

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I)

non-decorative type, core of block board construction with frame of 1st class

1.70 9.21 hard wood and well matched commercial 3 ply veneering with vertical grains or - -

cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium extruded section body tubular type universal HS

3000 Slimline Concealed Door Closer (having brand logo with ISi, IS :

3564,embossed on the body, door weight upto 36 kg to 80 kg and door

1.80 MR widthfrom 701 mm to 1000 mm), with double speed adjustment with necessary each 7,200.02 4.00 28,800.10

accessories and screws etc. complete

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI marked,

anodised (anodic AC 10 as per IS : 1868 ), transparent or dyed to required colour

or shade, complete:

DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor

stopper with necessary screws, etc. complete.

MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular Handle TH

123 with Roses & Escutcheon in SS packaged with Mortice lockset 55mm backset,

1.11 MR 20 SS forend, SS strike plate and EP Cylinder for all flush doors. EACH 3,250.01 4.00 13,000.04

Providing and fixing 600 mmx25 mm H Type handle for Doors approved make

and designs as per engineer in charge

Providing and fixing minimium 100 kg capacity flooor spring for Doors approved

make and designs as per engineer in charge

Providing and fixing Glass door lock approved make and designs as per

engineer in charge

2.00 CEILING - -

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

Providing and fixing false ceiling at all height including providing and fixing of

frame work made of special sections, power pressed from M.S. sheets and

galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277

and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of

27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of

cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle hanger fixed with intermediate G.I.

channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to

which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered

flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall

be fixed in a direction perpendicular to G.I. intermediate channel with

2.1 12.45 connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every - -

junction, including fixing perimeter channels 0.5 mm thick 27 mm high having

flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition

with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @

230 mm interval, including fixing of gypsum board to ceiling section and

perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm

c/c, including jointing and finishing to a flush finish of tapered and square edges

of the board with recommended jointing compound , jointing tapes , finishing

with jointing compound in 3 layers covering upto 150 mm on both sides of joint

and two coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills, diffusers,

cutouts made with frame of perimeter channels suitably fixed, all complete as

per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with :

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I)

:2011 (Board with BIS certification marks) sqm 1145.95

Providing and fixing mineral fiber falce ceiling With 16 mm thick beveled tegular

mineral fibre false ceiling tile (NRC 0.55 to 0.6 tile m 595x595 moisture resistance

2.20 MR frame made glavinised silhoute section as per approved make direction of Sqm 3,250.00 80.00

engineer in-charge 2,60,000.00

CEILING PELMETS :- Providing and fixed pelmet of overall size 150mmx150mm and

made hardwood framings hung from ceiling @1000mm centre to centre with 1

2.3 MR nos of 12mm thk. fire retardant ply on vertical & 12mm thk. Commercial ply on RMT 960.00 10.00 9,600.03

horizontal surface (straight & curved). Inclusive of finishing in Paint.

3.0 FINISHING WORKS - -

Providing and applying plaster of paris putty of 2 mm thickness over plastered

3.1 13.26 surface to prepare the surface even and smooth complete. sqm 214.30 400.00 85,720.00

Wall painting with premium acrylic emulsion paint of interior grade, having VOC

(Volatile Organic Compound ) content less than 50 grams/ litre of approved

3.2 13.83 brand and manufacture, including applying additional coats wherever required - -

to achieve even shade and colour.

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

Applying priming coats with primer of approved brand and manufacture, having

3.3 13.85 low VOC (Volatile Organic Compound ) content. - -

With ready mixed pink or grey primer on wood work (hard and soft wood) having

VOC content less than 50 grams/ litre

Providing and fixing wall paneling and partition frame work made of 25x50 mm

3.50 MR aluminium section 600x600mm c/c distance as per approved make SQM 834.76 400.00 3,33,904.80

4.0 MISCELLANEOUS WORKS - -

BLINDS Providing & supplying of Window Blinds as per the approved sample in

required shade and style consisting, of ZEBRA BLINDS comprising of optima screen

Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-480G weight per

sq m, Thickness 0.67 mm, Yarn count 18-19/cm, having fire resistance standard –

NFPA 701-89 small testing ISO-5659-2 .Thetear resistance should be complying to

ISO4674 & breaking resistance – ISO 5081. The DRIVE UNIT shall be of clutch for

quick, easy and safe installation, moulded plastic with steel spring support and

inserted into the tube end. It shall be driven by a ball chain pulley with ball chain

and can be positioned at right side or left hand side of the Shade. The Shade

when lowering or raising, shall be automatically locked in position upon release

of the ball chain by means of a built in friction lock.Universal clutch for left and

right hand operation.Chain Gear Ratio of 1.75:1. The END PLUG shall be molded

4.1 M.R. of plastic witha steel location pin.The plug shall be inserted into the tube SQM 4,850.00 40.00 1,94,000.00

end.(Opposite to the Drive Unit) for ease of installation. The SUPPORT BRACKETS

shall be of coated steel & provided with covers and used in right hand or left

hand positions differentiated by the acceptance of the of the rectangular drive

unit support or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling

Mount (c) On Frame (d) in Recess. The Bracket should be protruding outside

maximum of 80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm

internal diameter & skin thickness of 1mm and shall incorporate a key way

integral with the tube to accommodate the spline. The BOTTOM RAIL shall be a

Flat Bottom made up of powder coated steel. The BALL CHAIN shall be 2mm

diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on

6mm pitch to form an endless ball chain. It is used for raising or lowering action of

FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass surface

4.2 M.R. as approval of the Architect. (Only film surface area shall be measured and SQM 2,250.01 10.00 22,500.09

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm Laminate

of matching, Shutters to be fixed to a frame. Rigidly fixed on both sides and top

finshed in laminate. No internal carcass required. All Hinges of hettich or

equivalent. Internal Surface of the shutter in balancing white laminate. All shutters

4.3 MR to be provided with Stainless steel louvers at the top and bottom of the shutter as SQM 14,342.05 2.00 28,684.10

per the site requirements and instrcution of the Engineer In charge.

Digitally signed by AMIT

S No. Description Unit Rate

Non DSR Total Qty DSR Amount NDS Amount

Providing and fixing Aluminium Skirting 100 mm ht - Groove skirting - Natural

Anodized Finish (Make- as per make list or equivalent)

Providing and Fixing Logo & Signage in 3D ,as per the approved Design/ pattern

with Mat /Gloss Finish Brass Letters with Mettalic/ Acrylic Base, complete as

4.7 MR required at site with the direction of the Enginner In Charge sq inch 4,250.00 10.00 42500.00

Providing and Fixing of floor tiles with wear layer is of 0.5mm, made upof Stone

Polymer composite, 100% Water & Termite proof, Scratch/ Flame/ UV resistant,

anti-microbial, 100% recyclable Green product having click system with suitable

3.2 MR skirting. Classification of abrasion resistance (Abrasion wheelfromH-18 Calibrade, SQM 4,250.00 120.00 5,10,000.00

loadApplied 1000 grams, No. of Cycles 14,400). " ( Along with Matching Profiles)

Digitally signed by AMIT

Electrical/FA/PA

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

1.0 DISTRIBUTION BOARDS.

Supplying and fixing following way, horizontal type three pole

and neutral, sheet steel, MCB distribution board, 415 V, on

surface/ recess, complete with tinned copper bus bar, neutral

bus bar, earth bar, din bar, interconnections, powder painted

including earthing etc. as required. (But without

MCB/RCCB/Isolator)

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C"

curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase

and neutral), 415 volts, residual current circuit breaker (RCCB),

1.4 having a sensitivity current 30 mA in the existing MCB DB - -

complete with connections, testing and commissioning etc. as

2.0 CABELS / MAINS - -

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supply ,laying,testing and commissoning of 1100V grade

armoured cable having sector / circular shaped aluminium /

copper conductor PVC insulated cores under ground PVC tape

wrapped inner sheathed, GI strip / wire armoured and overall - -

extruded PVC sheathed confirming to IS: 1554, laid on wall or

ceiling using GI clamps and spacers as per route shown at site

and further as directed by Engineer-in charge

2.1 MR 16 Sq.mm 4 core copper cable mtr. 825.00 20.00 16,500.00

2.1 MR 25 Sq.mm 4 core copper cable mtr. 1,450.00 20.00 29,000.00

4.0 WIRING - -

Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor single core

cable in surface / recessed medium class PVC conduit, with

4.1 1.10 modular switch, modular plate, suitable GI box and earthing the - -

point with 1.5 sq.mm FRLS PVC insulated copper conductor single

core cable etc. as required.

a 1.10.3 One light point controlled by one 6A switch Per Pts 1,467.00 25.00 36,675.00

Wiring for group controlled (looped) light point/fan point/exhaust

fan point/ call bell point (without independent switch etc.) with

1.5 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed steel conduit,

4.2 1.54 and earthing the point with 1.5 sq. mm FRLS PVC insulated copper - -

conductor single core cable etc. as required

Wiring for circuit/ submain wiring alongwith earth wire with the

4.3 1.7 following sizes of FRLS PVC insulated copper conductor, single - -

core cable in surface/ recessed steel conduit as required.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

Wiring for twin control point wiring using 1.5 sqmm copper

conductor FRLS PVC insulated copper conductor cable drawn

through 25 dia MS conduit laid in surface/concealed over false

4.4 1.4 ceiling or in slab/wall chases including ,2way modular Per Pts 1,981.00 10.00 19,810.00

switches,modular plate ,suitable GI box and earthing the point

with 1.5 sqm FRLS PVC insulated copper conductor single core

cable as required

Supplying and fixing following modular switch/ socket on the

4.5 1.24 existing modular plate & switch box including connections but - -

excluding modular plate etc. as required.

c 1.24.4 3 pin 5/6 A socket outlet Each 122.00 50.00 6,100.00

d 1.24.5 6 pin 15/16 A socket outlet Each 197.00 90.00 17,730.00

Supplying and fixing following size/ modules, GI box alongwith

4.6 1.27 modular base & cover plate for modular switches in recess etc. as - -

Supplying and fixing following Modular base & cover plate on

existing modular metal boxes etc. as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm

solid copper conductor PE insulated, shielded with fine tinned

copper braid and protected with PVC sheath in the existing

surface/ recessed steel/ PVC conduit as required.

Supplying and laying HDMI Cable with connector on both ends

upto 15m length or as per site requirement

5 LIGHTING FIXTURES - -

LINEAR LIGHT 28-36W as per the specifications and direction of

Engineer In-charge

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Supply, Installation, Testing and Commisioning of pre-wired round

shape Surface Mount 15Watt LED Down Lighter fitting complete

with all accessories, housing made of Aluminium Die-cast, System

Efficasy >100 LPW, CRI >80, CCT of 4000K. suitable for 220 V, 50 Hz,

The luminare rated life (L70) >50000 Hours with High efficiency

5.2 MR driver with inbuild surge protection, over voltage protection, short NOS 1,470.91 40.00 58,836.23

circuit protection and operating at >0.95 PF., BIS approved Driver

including connection with 1.5 sq. mm FR PVC insulated, copper

conductor, single core cable and earthing etc as required.

Supply, Installation, Testing and Commisioning of 600X600 36-

40Watt LED fitting complete with all accessories, housing made

of Aluminium Die-cast, System Efficasy >100 LPW, CRI >80, CCT of

4000K. suitable for 220 V, 50 Hz, The luminare rated life (L70) >50000

5.5 MR Hours with High efficiency driver with inbuild surge protection, NOS 3,250.00 20.00 65,000.00

over voltage protection, short circuit protection and operating at

>0.95 PF., BIS approved Driver including connection with 1.5 sq.

mm FR PVC insulated, copper conductor, single core cable and

earthing etc as required.

6 WIRING FOR DATA AND VOICE OUTLETS - -

Supply and fixing the following sizes of PVC medium duty ISI

marked conduits (IS : 9537 Part-III) complete with accessories

6.1 such as bends, junction boxes, pull boxes etc., in recess or on - -

surface including cutting chases in the walls/floors and making

good the same complete as required.

Supplying and drawing of CAT 6A U/UTP cable, white jacket, 4 pair

6.2 1.53 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as - -

Supply & fixing of Plug in type information outlet (campatible with

6.3 MR data cables) in existing faceplate/ GI Box in wall/furniture/floor Nos. 582.51 60.00 34,950.56

complete as required.

Supplying and fixing following modular switch/ socket on the

6.4 1.24 existing modular plate & switch box including connections but - -

excluding modular plate etc. as required.

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

No. Telephone socket outlet

Supply and fixing of the following types Face Plates complete

with all accessories.

Supply & Fixing of Dual Faceplate, Duplex Port (for data and for

voice) or as required square plate having spring shuttered front

a. MR access for preventing ingress of dust, dimension as per Nos. 90.04 40.00 3,601.58

commercially available modular office furniture.

Supply ,laying ,installing , testing and commmissioning of the 50

pair multi core 0.61 mm annealed copper conductor PVC

insulated and PVC sheathed armoured telephone cables

6.6 MR generally conforming to ITD S/WS-11-C and IS 1554 part I direct in mtr. 457.57 50.00 22,878.28

ground /surface and / or in existing pipe as required and includig

making terminal joints, complete as required.

Supplying, installing, testing and commissioning of 24 port Cat 6A

patch panels available with block of four equipped with tool less

6.7 MR IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6A EACH 16,491.19 1.00 16,491.19

U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6

X RJ 45 Tool less connector U/UTP unit in a block.

7 CABLE TRAY.& RACE WAY. - -

GI Raceway & Junction boxes ( Raceway on floor shall be of

aluminium only)

MR Providing and fixing 2 mm thick steel sheet factory fabricated

post galvanized raceway with internal partition/compartmentized

of the following sizes including providing removable 3 mm thick GI

cover, knock out holes and fixing accessories earthing with 8 SWG

copper earth wire complete as required including floor supports, - -

bends, access boxes, tap off boxes and cross over as per

specification and site requirement. (overhead / wall mounted

recovery & function boxes shall be 1.6 mm thick)

c) MR 150 mm wide x 38 mm deep raceway or as per site RM 1,603.10 10.00 16,031.00

d) MR 100 mm wide x 38 mm deep raceway or as per site RM 1,250.00 10.00 12,500.00

MR Providing and fixing 150 x 150 x 60 mm deep 1.6 mm thick GI sheet

7.4 junction box including providing 3 mm thick stainless steel cover Nos. 1,874.51 5.00 9,372.54

as per specification.

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

A. No. SITC OF FIRE ALARM SYSTEM & ACCESSORIES : - -

Supplying, installation, testing & commissioning of intelligent Pcs

1 17.2.4 analog addressable photothermal detector complete with 2858.00 10.00 28,580.00

mounting base complete as required.

Supplying, installation, testing & commissioning of addressable Pcs

manual call point complete as required.

Supplying, installation, testing & commissioning of addressable Pcs

horn cum strobe complete as required.

Supplying, installation, testing & commissioning of fault isolator Pcs

complete with base as required.

Supplying, installation, testing & commissioning of response Pcs

indicator on surface/recessed MS Box having two LED, metallic

cover complete with all connections etc as required.

Supplying, installation, testing and commissioning of micro

processor based intelligent addressable main fire alarm panel,

central processing unit with the following loop modules and

capable of supporting not less than 240 devices (including

detectors) and minimum 120 detectors per loop and loop length

up to 2 km, network communication card, minimum 320

character graphics/ LCD display with touch screen or other

keypad and minimum 4000 events history log in the non volatile

6 17.2.1 memory (EPROM), power supply unit (230 ± 5% V, 50 hz), 48 hrs - -

back-up with 24 volt sealed maintenance free batteries with

automatic charger. The panel shall have facility to connect

printer to printout log and facility to have seamless integration

with analog/digital voice evacuation system (which is part of the

schedule of work under SH: PA System) and shall be complete

with all accessories . The panel shall be compatible for IBMS

system with open protocol BACnet/ Modbus over IP complete as

B CABLES & ACCESSORIES FOR FAS : - -

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, RM

600/1000V rated with annealed copper conductor having

6 17.5.2 XLPE insulation, steel wire armouring & FRLS outer sheath 173.00 200.00 34,600.00

complete as required.

Digitally signed by AMIT

DSR- Description

S.No Unit Rate Total Qty DSR Amount NDSR Amount

C No. SITC OF PUBLIC ADDRESSABLE SYSTEM & ACCESSORIES : - -

Supplying, installation, testing & commissioning of Pcs

7 17.3.4 ceiling/wall mounted loud speaker, 3/1.5 Watt in ABS 2428.00 5.00 12,140.00

enclosure complete as required.

Total DSR & Total Non DSR 7,41,701.00 3,05,108.57

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

Supply Installation, Testing & Commissioning of modular type Variable

Refrigerant Flow/ Variable Refrigerant Volume air cooled Outdoor

units suitable for cooling and heating, having all hermetically sealed

inverter type Scroll Compressor(s), minimum two compressors for

above 14 HP modules, microprocessor based Controller, top

discharge type condensing unit(s), with R410A Refrigerant, vibration

1.0 1.1 isolators, with suitable foundation etc. complete as required.The unit Per HP 16415 20.00 3,28,300.00

shall deliver the rated capacity at AHRI Conditions and work even at

50°C ambient temperature without tripping.The unit shall be suitable

to work on 400V+/-10%, 3 Phase, 50Hz AC power supply.The unit shall

be filled with first charge of the refrigerant and ready for use as

required.The COP at AHRI conditions shall not be less than 3.1 and

IEER not less than 6.5 .

2.0 INDOOR UNIT

Supply, installation, testing and commissioning of following minimum

capacity 4-wayflow VRV/ VRF Cassette Type Indoor ceiling mounted

unit equipped with synthetic washable media pre-filter, fan section

with low noise fan/ dynamically balanced blower, multi speed motor,

coil section with DX Copper coil, electronic expansion valve, outer

cabinet, drain pump, grill, necessary supports, vibration isolation,

cordless remote control etc., suitable for operation on single phase

230V±10%, 50 HzAC supply, complete, as required. The unit shall have

automatic force shut down provision in case of fire on receiving

signal from BMS System. The cooling capacity of indoor unit will be at

air inl et conditions of 27 Degree CD Band 19 Degree CWB

4-Way Cassette type - -

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

3.0 REFRIGERANT PIPING - -

Supply, Installation, testing and commissioning including

vaccumiazation and Nitrogen testing of following nominal sizes of

soft/hard drawn copper refrigerant piping for VRV/VRF system,

DSR 2019 complete with fittings, with suitable adjustable ring type hanger

3.0 VRF/VRV supports, jointing/brazing including accessories, insulated with XPLE - -

Item No 5 Class-O tubular insulation/with Class-O closed cell elastometric

nitrile rubber tubular sleeves sections of specified thickness as given

below for Suction and Liquid lines, all accessories as per

specifications etc. as required :

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

19.2 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick

34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm with 19 mm thick

4 CONDENSATE DRAIN UPVC PIPE - -

Supply, installation, testing and commissioning of uPVC Pipe ,complete with

fittings, supports,U trap arrangement,Clean Plug with 6mm nitrile insulation and - -

accessories as per specifications, drawings.

4.3 MR Imported fittings Y-joints and headers etc. Nos 4281.4 8.00 34,251.26

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Rate Total Qty DSR Amount NDSR Amount

Providing and fixing control cum transmission wiring of 2 core x 1.0 sq. mm copper

in suitable conduits between indoor and outdoor unit.

MR Supply and fixing IP-55 based outdoor MCB box with 1 NOS 65 amp RCCB Nos 14650.0 1.00 14,650.00

Supply and fixing MS base frame for VRV outdoor stand as per approved size

Digitally signed by AMIT

Sr. No. Item Description Unit Rate Qty Amount

DSR/ Supply, Installation, Testing & Commissioning of 24 PORT Managed Network Switch

Supply, Installation, Testing & Commissioning of 5MP IR IP H.265 Vandal Proof Dome camera with

2.8 to 12mm Motorized Lens,Smart IR, up to 30M IR distance,Up to 120 dB WDR (Wide Dynamic

Range),3D DNR (Digital Noise Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode, Triple

streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4, AGC ON), 0 Lux with IR,Video

Compression H.265+, H.265, H.264, MJPEG,Behavior Detection Intrusion, Crossing line, Motion

detection, Object left, Missing object,Intelligent Identification Face detection, Defocus, Scene

Change,PoE (IEEE802.3 af) Power consumption: Max 7.2W,Edge Storage Micro SD Card, Up to

256GB, ANR Support,Working Environment -40°C ~ +60°C, Humidity ≤ 90% RH(Non-

condensing),Compatible Integration ONVIF (Profile S/G), API.

Supply, Installation, Testing and Commissioning of 8Ch Embedded Network Video Recorder with 4

2 MR Sata Supports 1 × RJ45 1000M ,4K Cameras, HDMI, VGA, RAID, Redundant power supply, Smart Nos 95,650.00 1 95,650.00

Analytics and ONVIF

SITC of SSD Hard Disk Drive 4TB, 24/7 surveillance category Only complete etc as required.etc.all

50 Pair MDF Box -

1 MR 50 Pair MDF Box with mounting Frame Nos. 16,500.00 1 16,500.00

Digitally signed by AMIT

Specifications Rate Qty Amount

GM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non

working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table

top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

1 drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall 78,500 1.00 78,500.00

be made out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6 module

fliptop box for wire passing or as per site requirement.Main Table Dimension (L)2100mm X (D)

900mm X (H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

GM High Back Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-

Chair (W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

upholstered with leatheritte and cut foam. The chrome plated loop armrest with padded

2 upholstery is provided for extra comfort. The chair shall be provided with pneumatic height 26,600 1.00 26,600.00

adjustment which shall have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/-2kg

/m3) Dimensions The backrest has a foam of 28kg/m3.

GM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm

Back Chair X (H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium

Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back

Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating Height:19".The

3 Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with 19,600 4.00 78,400.00

polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of

Digitally signed by AMIT

Specifications Rate Qty Amount

DGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non

working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table

top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall

be made out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6 module

fliptop box for wire passing or as per site requirement.Main Table Dimension (L)1800mm X (D)

900mm X (H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

DGM High Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-

Back Chair (W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

upholstered with leatheritte and cut foam. The chrome plated loop armrest with padded

5 upholstery is provided for extra comfort. The chair shall be provided with pneumatic height 24,650 1.00 24,650.00

adjustment which shall have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/-2kg

/m3) Dimensions The backrest has a foam of 28kg/m3.

DGM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm

Back Chair X (H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium

Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back

Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating Height:19".The

6 Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with 19,600 3.00 58,800.00

polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of

2 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the

soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour

Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech solid

wood have used for framing construction of sofa .The seat cushion is made of multi layered foam

7 of density 32-35 kg/m3. The seating cushion have 2.75 & 42,500 5.00 2,12,500.00

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength .

The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

Digitally signed by AMIT

Specifications Rate Qty Amount

8 TABLE CENTRE TABLE WITH GLASS TOP 16,500.00 1.00 16,500.00

9 TABLE SIDE TABLE WITH WOODEN STRUCTURE 12,500.00 3.00 37,500.00

AGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non

working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table

top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

10 drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall 55,650 1.00 55,650.00

be made out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6 module

fliptop box for wire passing or as per site requirement. Main Table Dimension (L)1800mm X (D)

900mm X (H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

AGM and PS Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

High Back 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof

Chair plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS

grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be

provided with self tension single locking mechanism and pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height adjustment shall have adjustment

stroke of 100 mm and shall be operated at 30kgs extension force.The Seat & back are made up of

12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

PS Table Supplying and placing in position of main table as per photograph/drawing .The table shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non

working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table

top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

12 drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall 42,500 1.00 42,500.00

be made out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6 module

fliptop box for wire passing or as per site requirement. Main Table Dimension (L)1500mm X (D)

900mm X (H)750mm overall Side Runer Dimension (L)1200mm X (D) 450mm X (H) 675mm

Digitally signed by AMIT

Specifications Rate Qty Amount

Reception Supplying and placing in position of main table as per photograph/drawing .The table shall be

table with made out of 25mm thick pre -laminated particle board of approved shade. The working and non

side storage working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table

top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

13 drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall 42,500 1.00 42,500.00

be made out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6 module

fliptop box for wire passing or as per site requirement. Main Table Dimension (L)1500mm X (D)

900mm X (H)750mm overall Side Runer Dimension (L)1200mm X (D) 450mm X (H) 675mm

Modular Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side

Workstation Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht.

1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side

laminated and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end

14 18mm thick MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H 32,650 3.00 97,950.00

made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For

drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-Munshel Gray. and

White Tinted Glass

Linear Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

Workstation workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and

50mm x 25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk

Metal panel fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation).

0.8 mm thk Single/Double metal powder coated raceway with Powder coting of 50 Micron below

top for wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non-

sharing workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of

glass divider rest on the "D" brackets on the table top between opposite seatings. All working or non

15 working edges shall be provided with machine pressed 2mm thick PVC edging using special hot 26,650 1.00 26,650.00

melt glue at hot temperature. Provision of pullout PVC keyboard tray and CPU trolley for each

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2

drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Digitally signed by AMIT

Specifications Rate Qty Amount

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of

chair Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design

contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

upholstered with leatheritte and cut foam. The chair shall be provided with pneumatic height

16 adjustment which shall have stroke of 10.0 +/- 16,500 7.00 1,15,500.00

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg

/m3) The backrest has a foam of 28kg/m3.

Back side The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is

Storage made of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided

17 with machine pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with -

free groove handle and suitable lock. All exposed area PVC edge lipping

Branch Supplying and placing in position of main table as per photograph/drawing .The table shall be

incharge made out of 25mm thick pre -laminated particle board of approved shade. The working and non

Table working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table

top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

1 drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall 65,650 1.00 65,650.00

be made out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6 module

fliptop box for wire passing or as per site requirement.Main Table Dimension (L)1800mm X (D)

900mm X (H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

Branch Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size :-

inchargeHigh (W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

Back Chair lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

upholstered with leatheritte and cut foam. The chrome plated loop armrest with padded

2 upholstery is provided for extra comfort. The chair shall be provided with pneumatic height 24,650 1.00 24,650.00

adjustment which shall have stroke of 10.0

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/-2kg

/m3) Dimensions The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Specifications Rate Qty Amount

Branch Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm

incharge X (H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium

Visitor Back Leatherette, Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back

Chair Type:Cantilever, Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating Height:19".The

3 Seat & back are made up of 12mm thk hot pressed plywood upholstered with PVC with 19,600 3.00 58,800.00

polyurethane foam, chair seat has foam of density 32-35 kg/m3. The backrest has a foam of

AGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be

made out of 25mm thick pre -laminated particle board of approved shade. The working and non

working edges shall be finished with machine pressed with 2mm PVC egdge banding. The table

top shall be supported with MS powder coated "C" shape leg of size 50mm x 50mm with

connectors of size 40mm x 40mm. The front modesty are made out of 18mm thick prelaminated

particle board with 2mm thk pvc edge banding. The table shall be provisioned with Side unit of

overall size: 1800mm(L) x 450mm(D) x 675mm(H) . Side storage having a provision for three equal

4 drawer unit and two openable shutter & one open storage with shelf in it. The Side unit top shall 55,650 2.00 1,11,300.00

be made out of 18mm thick pre laminated particle board and rest all storage to be made out of

18mm thick pre laminated particle board. Provision of Junction box, wire raceway and 6 module

fliptop box for wire passing or as per site requirement. Main Table Dimension (L)1800mm X (D)

900mm X (H)750mm overall Side Runer Dimension (L)1800mm X (D) 450mm X (H) 675mm

AGM High Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

Back Chair 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof

plywood and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS

grade - 303) upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be

provided with self tension single locking mechanism and pneumatic height adjustment which shall

have stroke of 10.0 +/- 0.3 cm .The black .The pneumatic height adjustment shall have adjustment

stroke of 100 mm and shall be operated at 30kgs extension force.The Seat & back are made up of

12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has foam

of density 32-35 kg/m3. The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Digitally signed by AMIT

Specifications Rate Qty Amount

2 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the

soft cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour

Family:as per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech solid

wood have used for framing construction of sofa .The seat cushion is made of multi layered foam

6 of density 32-35 kg/m3. The seating cushion have 2.75 & 42,500 2.00 85,000.00

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength .

The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

7 TABLE CENTRE TABLE WITH GLASS TOP 16,500.00 1.00 16,500.00

Back side The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is

Storage made of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided

8 with machine pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with -

free groove handle and suitable lock. All exposed area PVC edge lipping

Conference Supplying and placing in position of conference table of required size as per image/drawing. The

Table work surface top should be of thickness 42mm top prelaminated particle board with 2mm thick

PVC edge banding. The side panel are made up of 36mm thick prelaminated particle & modesty

panel are made out of 25mm thick prelaminated particle board with 2mm thick PVC edge

9 banding. The wire carrier should be made from 0.6mm thick CRCA & powder coated 40-50 95,000 1.00 95,000.00

microns. Also having a provision of 6 module flip top box & metal raceway for wire flow.

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of

chair Size :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design

contour lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back)

upholstered with leatheritte and cut foam. The chair shall be provided with pneumatic height

10 adjustment which shall have stroke of 10.0 +/- 16,500 20.00 3,30,000.00

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/-2kg

/m3) The backrest has a foam of 28kg/m3.

Digitally signed by AMIT

Specifications Rate Qty Amount

Modular Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side

Workstation Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht.

1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side

laminated and upper tile inside side fabric, White

Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end

11 18mm thick MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H 32,650 5.00 1,63,250.00

made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For

drawer Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating-Munshel Gray. and

White Tinted Glass

Linear Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

Workstation workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and

50mm x 25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk

Metal panel fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation).

0.8 mm thk Single/Double metal powder coated raceway with Powder coting of 50 Micron below

top for wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non-

sharing workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of

glass divider rest on the "D" brackets on the table top between opposite seatings. All working or non

12 working edges shall be provided with machine pressed 2mm thick PVC edging using special hot 26,650 3.00 79,950.00

melt glue at hot temperature. Provision of pullout PVC keyboard tray and CPU trolley for each

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of 2

drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Pantry Table Providing & Installation of Pantry table of size 1.8m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per

13 design. The Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be 24,345 2.00 48,690.00

provided above table. One (1) number Drawer pedestal with 3 drawers to be provided under the

Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC

Total Amount 24,53,720.00

Total Amount 24,53,720.00

Digitally signed by AMIT