Balance Civil Work and Plumbing work at Rajiv Gandhi Hospital Gangyal Jammu.

Amount

Earth work in excavation by manual means in foundation trenches, drains, pipes and cables etc. (not exceeding 1.5mtr in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift upto 1.5mtr including getting out excavated soil and disposal of surplus soil as directed, within a lead of 50 mtr. All kinds of soils

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level:- (Including cost / Carriage of material by Mechanical transport) 1:5:10 (1 cement: 5 coarse sand :10 graded stone aggregate 40 mm nominal size) :- CRUSHED

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering; at all floor levels completeAll work above plinth level upto floor five level:- (Including cost / Carriage of material by Mechanical transport) 1:3:6(1 cement: 3 coarse sand :6 graded brick aggregate 20 mm nominal size):-

Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth including curing in:- Cement mortar 1:6 ( 1 cement : 6 coarse sand); (Including cost / Carriage of material by Mechanical transport)

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering. shuttering, finishing and reinforcement:- 1:1.5:3 (1 cement: 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size):- CRUSHED (Including cost / Carriage of material by Mechanical transport)

15mm Cement plaster on the rough side of single or half brick walls of mix: 1 : 6 ( 1 cement : 6 fine sand) on interior walls ,all complete including making of groves and scaffolding, etc. at all floor levels complete (Including cost / Carriage of material by Mechanical transport)

20mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand) ,in two coats on exterior walls, all complete including making of groves and scaffolding etc., all floor levels complete (Including cost / Carriage of material by Mechanical transport)

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-mechanically treated bars of grade Fe-500D or more (Including cost / Carriage of material by Mechanical transport)

Centering and shuttering including strutting, propping etc. and removal of form work for:-

Foundations: footings, bases of columns etc. for mass concrete.

Lintels, beams, plinth beams, girders,bressumers and centilevers.

Suspended floors, roofs, landings, balconies and access platform.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture of Birla/JK white only over the plastered wall surface to prepare the surface even and smooth complete.( Inner walls and ceilings) at all floor levels complete including scafolding:- (Including cost / Carriage of material by Mechanical transport)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surfaces

Wall Painting with plastic Emulsion Two or more coats of approved brand and manufacture

Finishing walls with Water Proofing Cement paint of required shade New Work( Two or more coats)

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28litre/10sqm over and including base coat of waterproofing cement paint applied@ 2.20kg/10sqm); and also providing weather shield protection coat over the textured surfaces, all complete of approved brand and manufacture Asian/Nerolac/Berger/Dulux paints only all complete including scaffolding etc.; at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and laying of vitrified floor tiles (double charged) in different sizes (thickness to be specified by the manufacturer) (Anti-skid) with water absorption less than 0.08% and conforming to lS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete SOMANY/ KAJARIA or equivalent only make; at all floor levels complete:- (Including cost of labour, Cement and Sand but excluding cost of tiles).

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like SOMANY/KAJARIA only make in all colour, shades except begundy,bottle green, black of any size as approved by Eningeerin-Charge in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarsesand) and jointing wtih grey cement slurry@ 3.3 kg persqm including pointing in white cement mixed withpigment of matching shade complete, at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour or shade:-Polished Granite stone slab jet Black, Cherry Red, Eliten Brown, Cat Eye or equivalent. (Area of slab over 0.5 sqm) 18 mm thick (Including cost / Carriage of material by Mechanical transport) (a) Kitchen

Extra for providing opening of required size and shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble I stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete. (Including cost / Carriage of material by Mechanical transport)

Steel work welded in built up sections/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladders, railings, brackets, gates & similar works all complete.( Cattle Trap)

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge

Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m. (stacks of cleaned bricks shall be measured) :

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared

Disposal of surplus excavated material laying at site by way of mechanical transport upto lead 3km

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles above 25 mm and upto 40 mm.

Actual labour engaged from time to time for clearing choked backside drain

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS :·13753 of minimum thickness 5 mm of approved make like SOMANY/KAJARIA only make in all colour, shades except begundy,bottle green, black of any size as approved by Eningeerin-Charge in skirting, risers of steps and dados over 12mm thick bed of Cement Mortar 1:3 ( 1 cement: 3 coarsesand) and jointing wtih grey cement slurry@ 3.3 kg persqm including pointing in white cement mixed withpigment of matching shade complete, at all floor levels complete:- (Including cost / Carriage of material by Mechanical transport)

Providing and laying half brickwork in mix(1:4)

PLUMBING & SANITARY

Providing and fixing unplasticised - Rigid PVC PIPES conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap of thermal expansion;with necessary stays / clamps with fasteners having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport)

50 mm dia

75 mm dia

110 mm dia

160 mm dia

Providing and fixing unplasticised - PVC Moulded Fitting/Accessories conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10mm gap of thermal expansion;with necessary stays / clamps with fasteners having working pressure of 4kg/cm2 of make Supreme or finolex only :- all complete including testing of joints and pipes for leakage etc.:- (Including cost / Carriage of material by Mechanical transport)

PVC COUPLER/ COLLOR:-

50 mm dia.

75 mm dia.

110 mm dia

PVC DOOR TEE/ Single Tee with Door:-

110 x 110x 110 mm dia./110 x 110x75 mm dia.

PVC PLAIN TEE( Single Tee without Door):-

110 x 110x75 mm dia.

110 x 110x 110 mm dia.

PVC PLAIN /Door BEND (of required degree):-

50 mm dia.

75 mm dia.

110 mm dia

Clamps with Screws:-

110mm dia.

PVC Offset with rubber washer:-

75mm dia.

110mm dia.

Providing and fixing white vitreous china pedestal type water closet (European type W.C . .pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures, complete including cutting and making good the walls and floors wherever requied W.C. pan with lSI marked white solid plastic seat and lid of make Hindware/Cera/Jaquar only:- (All Carriages)

Providing and fixing wash basin with C. I./M.S. brackets,15mm C.P. centre hole basin mixture, 32 mm C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps of make Hindware/Cera/Jaquar only:- (All Carriages) including a pillar cock, CP brass basin mixture, Pillar tap 15mm

Round basin 405x355 with single 15mm C.P. Brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings of make Hindware/Cera/Jaquar only:- (With Carriages)

Providing and fixing Salem Stainless Steel A lSI 304 (18/8) kitchen sink including waste coupling as per I.S. 13983 with C.l. brackets and stainless steel plug 40 mm including painting of fitting sand brackets, cutting and making good the walls wherever required of make Kaff/Neelkanth/Hindware or equivalent all complete :-610x460mm bowl depth 200mm (With Carriages)

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete. Flexible pipe 40 mm dia (With Carriages)

Providing and fixing mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete ISI marked of make Saint Gobin or Modi float or equivalnet brand as approved by Engineer incharge at site:- (With Carriages)

Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C. P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete of make hindware/Cera/Jaquar only:-

Providing and Fixing Central hole basin mixer witout popup waste system with 450mm long hoses with necessary screws

Providing and fixing towel ring (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and Fixing PVC FLOOR/NAHANI TRAP of required angle of self cleansing design with c.p. grating of required size including cost of cutting

110 mm x 75 mm /110 mm x 100 mm

Providing and fixing G.l. pipes complete with G.l. fittings and clamps, including cutting and making good the walls etc.(internal work) of make Jindal/Surya Prakash of medium class or as approved by site incharge (INTERNAL WORK-Exposed on wall) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc. (Incl. all carriages)

15 mm dia. nominal bore (medium)

25 mm dia. nominal bore (medium)

Making connection of G.l. distribution branch with G.l. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make UNIK or NEW or equivalent as approved by site incharge (Incl. all carriages)

20 to 40 mm nominal bore

Providing & fixing BRASS BALL VALVE of approved quality conforming to IS : 8931 of make UNIK or DRP or as approved by site incharge (incl. all carriages)

15 mm nominal bore

25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore (With all Carriages)

Providing and fixing G.l. Union in G.l. pipe including cutting and threading the pipe and making long screws etc. complete (new work) all complete including testing of pipes and fittings and joints for leakage with pressure pump etc.of make UNIK or NEW or equivalent as approved by site incharge (Incl. all carriages)

15 mm nominal bore

25 mm nominal bore

40 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license] (incl. cost / carriage of material upto roof top).

Providing and fixing G.I.TANK NIPPLE of suitable dia. of make UNIK or NEW or equivalent ISI marked as approved by engineer incharge at site all complete including testing of fittings and joints for leakage etc.:- (incl. all carriages)

15 mm dia. nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS : 8931 of make hindware/Cera/Jaquar only:-. (a)15 mm nominal bore (With all Carriages) Short body

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms of make hindware/Cera/Jaquar only: (With all Carriages) a) 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin/wall mixer and geysers points of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge (With all Carriages)

Providing and fixing Soap dish (C.P. brass) with brackets ,nuts & screws complete etc. of make hindware/Cera/Jaquar only:- (With all Carriages)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge all complete of make hindware/Cera/Jaquar only:-. (With all Carriages)

Providing & fixing PVC VENT COWL:-

110mm dia

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) R.C.C. top slab with 1 :2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finsihed with a floating coat of neat cement complete as per standard design (Including cost / Carriage of material by Mechanical transport)

Providing and laying cement concrete (1:5:10) with 20mm size aggregate all around the PVC Pipe including bed concrete as per approved by site incharge.

Labour charges for core cutting to RCC beam & PCC drain for crossing PVC pipe lines.

Cutting chases in brick masonary walls and making good to same with cement concrete(1:3:6) including necessary plaster and pointing in cement mortar(1:4)

Deepak Goswami