SPECIAL REPAIR TO OFFRS ACCN AT JDC AND NP 47 NP 48 AND NP 49F IN STN NCC OFFRS MESS AND CERTAIN REV WORK AND MINOR WORK AT MIL STN JAMMU UNDER GE SATWARI

Amount

Demolition of cement concrete (unreinforced) ground floor to 2nd floors and pavings n exc 15 cm thickness (below or above ground level ) and removing the rubbish from the work site out side defence premises complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding, terrazo dado from wall surface (but not backing), removing serviceable tiles to store and rubbish off the premises. Complete all as specied and directed.

Material and labour glazed ceramic coloured digital tiles in vertical surface 300x450x7 mm thick, set and jointed in neat cement slurry and pointed white or colored cement to match the surface over and including 10 mm thick CM 1:4 complete all as specified.

Material and labour Non - skid Digital Ceramic joint less coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/white cement to match the surface over and including 15 mm thick screed bed in CM 1:4 complete all as specified.

Description all as item No 4.0 but as in vertical surfaces dado/skirting over and including a backing coat of CM 1:4, 10 mm thick complete.

Material and labour Vitrified Ceramic(Double Charged) edge cut joint free coloured or printed any shade tiles 10 mm thick (square/ rectangular) polished area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match and set in neat cement slurry and pointed with coloured/ white cement to match over and including 15 mm thick screed bed in CM 1:4. (Sample as approved & Kept in GE's sample room)

Description all as item No. 6.0 above but as in vertical surfaces dado/skirting over a backing coat of CM 1:4, 10 mm thick complete.

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, over 15 mm thick CM 1:4 as directed by Engr-in-charge.

Taking down cement plaster of any description on brick or stone walls or from concrete surface including raking out joints, hacking for key, scrubbing down with water etc, and removing unserviceable material outside cantt area, complete all as specified.

M&L for rendering 15 mm thick on fair faces of brick or concrete surface walls, in cement mortar 1:4 , rendering is to be finished even and fair without using extra cement (up to 2nd storey with necessary scaffolding) complete all as specified and as directed by Engineer-in-charge.

M&L Rendering cement plaster, 15 mm thick on fair faces of brick/concrete surfaces of wall in cement mortar 1:6 finished even and smooth w/o using extra cement complete all as specified.

M&L Rendering 10 mm thick on fair faces of brick or concrete surface ceilings, in cement mortar 1:3, rendering is to be finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-charge.

M&L for machine cut kota stone slab flooring 18-20 mm thick over and including cement screed bed laid and jointed cement screed bed laidand jointed with grey camant slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for tread of staircase over and including 15mm thick screed bed in CM 1:4 all as specifid and directed

M&L for machine cut kota stone slab 15-18 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete for risers of staircase over and including 10mm thick fair and even plaster in CM 1:4 after roughing surfaces of old concrete/any type of plaster by picking sweeping down with water to remove dust etc.

M&L for rendering 15mm thck in CM 1:3 or Plain Cement Concrete as in sunken floors without extra cement on walls/floors and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L applying a coat of bituminous primer conforming to IS-3384 on prepared surface of roof/sunken slab after drying of primer apply APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) laid on primed surface by forced torched application and finally apply a coat of hot blown 85/25 graded bitumen conforming to IS-702 @ 1.2 Kg/sqm of plaster surface.

M&L Cement concrete type E-2, 1:5:10 ( 40 mm graded agregate) in Sunkan ( Up to 2nd floor) filling and mass concrete complete all as specified and directed by Emgr-in-charge.

M&L 40 mm dia G I tubing heavy grade galvanised laid over floors as a spout pipe in sunken floors all as specified.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified.

S&F pressed steel frames of size 125mm x 60mm made out of size 1.25mm thick MS sheet for doors double rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

S&F pressed steel frames of size 105mm x 60mm made out of size 1.25mm thick MS sheet for doors single rebated including mild steel hinges medium weight 100 mm long and 25mm x 3mm flat iron in holdfast,tie bar including necessary fixing lugs, hold fast, lock strike plate and fixing arrangement etc complete as specified and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 including PCC 1:3:6 as in back fill to chowkats all as Specified.

Supply and fixing 35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified

S&F Flush shutters, 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.Note :- Sampel approved by Engr-in-Charge or GE.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppplying and fixing in the frame at site as per specification & drawing complete all as specified and as directed by Engr-in-Charge.

Demolition of reinforced cement concrete of any discription ground to 2nd floors and removing the rubbish from the work site out side defence premises complete all as specified.

M&L for RCC M-15, nominal mix, type B-1(1:2:4), using 20mm graded crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified and directed.

M&L for TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for column, hooking end and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed.

M&L for use and waste form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work, not exceeding 200mm thick (horizontal or sloping) for fair finished surfaces of concrete, complete all as specified and directed.

M&L for use and waste form work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roof and not exc. 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10cm but n.exc. 20cm wide for fair finished surfaces of concrete, complete all as specified & directed

M&L for pressed steel cup board frame of MS sheet 1.25 mm thick size of frame 60 x 40 mm with rebate of 20 mm wide and 12 mm deep including PCC 1:2:4 as in filling to back of chowkats including butt hinges 100 mm long. Piano hinges measured separately.

M&L for prelaminated MDF board 19 mm thick as in shutters/shelves (exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame worknincluding lipping (15 mm thick three sides and 20 mm thick lipping hinge side) around the shutter complete all as specified and as directed by Engr-in-Charge.

S&F in repair continuous (piano) hinges, heavy duty mild steel, bright finish or electrogalvanised sutable for 19mm thick shutter and fixed, complete all as specified.

S&F butt hinges of mild steel cold rolled medium weight of size 100mm as specified.

S&F Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

S&F Aluminium handles, fabricated type, anodised Size-100mm, anodised section and fixed complete all as specified. (ISI Marked)

S&F Aluminium alloy, anodised, sliding door bolt Size- 250 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S & F hasp & staple safety type aluminium anodised with mild steel hinges Spin including bolt to hinges plate fixed with screws of 75 mm in length.

S&F aluminium hanging floor door stopper, twin rubber stopper, size 100mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc complete.

Supply and fixing in repair mild steel helical ordinary rat tail rod pattern springs 300mm including roller and roller plate complete including fixing to pressed steel frames necessary welding work all as specified and as directed.

Taking down of old/unserviceable kitchen cabinet/cupboard including all fixture and fitting, complete all as specified and directed.Note: For measurement superficial area in elevation shall be measured.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. One side prelam and other side plain18mm thick Celuka PVC ply for kitchen cabinet shutter and also manufactuer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 18mm(+0.7mm) thick celuka PVC ply of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 18mm thick Celuka PVC Ply for Shelf/Partitions/Drawer and also manufacturer's test report and test certificate is mandatory with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F factory made 5mm thick PVC of density 600Kg/cbm manufacured by an ISO 900-2008 certified company. Plain 5mm thick PVC sheet paneling for back side (wall side) and also manufacurer's test report and test certificate is mandotary with each and every supply of the material complete as per manufacturer's specifications and drawing and as directed.

S&F 100mm size Stainless steel handle complete all as specified and as directed.

S&F ball rolling sliding channels of size 450mm length fixed in cupboards with screws as in drawers

S&F Auto hinges of size 150mm length fixed in cupboards with screws for holding stainless steel baskets as in drawers

S&F self adhesive tape of 18/19mm width , hot pressed & pasted on sides & bottom of edges of cupboards shutters

S&F steel fasteners of size 75mm long drilled and fixed to walls

S&F 50mm dia and 75mm long steel supports fixed with bolt at bottom of cupboards box all as specified

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material from the work site ouside defence premises complete all as specified.

M&L for brick work with subclass 'B' bricks, old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-charge

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified.

Material & labour factory made steel windows/ ventilator double shutter box type, outer frame made out of ERW TUBE 'P' section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (ii) PCC block for embedding lugs. (Grill shall be measured separately)

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes framed guard bars barred iron doors ladders framed balusters walk ways railings framework of water tanks and similar work conforming to Fe.290.Gde-E-165

S&F 4 mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto second storey with necessary scaffolding), all as specified.

S&F 4 mm thick figured glass, pin head type and glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), all as specified.

Supply and fixing Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified fixed with stainless steel wire staples.

S&F in repair 25mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 25mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

Complete removal of existing water proofing treatment of any description incl under layer, taking down of cement plaster/demolition of cement concrete any thickness and removal of debris off the premises including grubbing up of trees and preparation of concrete surfaces by scrubbing down with steel brushes and cleaning with water to remove all loose dirt/dust.

M&L for P.C.C 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L Rendering 15mm thck in CM 1:4 on Concrete surfaces of roof finished fair & even and including mixing of water proofing compound (WPC shall be measured and paid separately)

M&L for water proofing treatment in the following sequences:- (a) Applying 1st course of bituminous primer conforming to IS -3384 @ 0.5 Kg/Sqm cover the surface till the surface properly impregnated and insolvent oil primer evoporate completely. (b) Applying 2nd coat of blown 85/25 graded bitumen confirming to IS 702 @ 1.2 Kg/sqm. (c) Applying 3rd course of APP (Atactic Polypropylene) modified polymeric membrane 3 mm thick weight not less than 3.6 Kg/Sqm with 160 Grams/Sqm non woven polyester made at centre core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane has to be laid with LPG torch and overlap sealed and finished neat complete all as specified and as directed .

M&L for preparation of newly sufrace of APP Membrane and applying two coats of water based bituminious alumunium paint @ 200 ml per sqm etc

Dismantling/ disconnecting/ demolition of water storage tank of any type or description (RCC/PVC/Bricks etc) and removing from site or refixing in position.

Supply and fixing in repair Rotational moulded polyethylene water storage tanks of 500 litres capacity, (cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified.

Supply and fixing in repair Rotational moulded polyethylene water storage tanks of 1000 litres capacity, (cylindrical vertical with closed top) triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections complete all as specified.

Supply and fixing in repair Gun-metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipe of 20 mm bore pipe, including making connections complete all as specified and fixed.

S&F in repair CP Bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed all as specified complete all as specified.

S&F in repair angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, complete all as specified.

S&F in repair Stop valves, cast copper alloy,fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified.

S&F in repair CP Pillar taps 15mm, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified.

S&F Cromium plated, minimum 20 mm dia, single towel rail 600mm long complete all as specified.

S&F in repair Chromium plated, towel ring, complete all as specified.

S&F in repair stainless steel Shop dish holder complete all as specified.

S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F in repair Corner Glass Shelf (with Bracket) as per directed by Engr-in-charge.

S&F in repair PVC connection 15 mm x 600 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore.

S&F in repair Brass chromium plated shower rose with or without swivel joints, 125mm size, including fixing to steel pipe or union

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, waste cuppling, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as specified and directed by Engineer-in-charge.

S&F in repair Vitreous China, wash basin white, flat back, size 550mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass complete all as specified and as directed by Engineer-in-charge.

S&F in repair full pedestal for WHB complete all as specified.

S&F in repair PVC valveless,syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair Vitreous china ware pedestal type water closet white, with 'P' or 'S' trap including self closing seat cover, closed pattern with flat bottom,complete all as directed.

S&F in repair WC Orissa pattern white with integral foot rest 580x 440 mm including L bend & PCC bedding in 1:2:4 and making good disturbed floor connecting to trap and flush pipe compete all as specified.(Rate of including in taking out and removal of old WC seat unhygienic condition)

Taking up or down steel tubing of 15 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Taking up or down steel tubing of 20 mm bore pipe and connections,including cleaning for re-fixing or removal to store, complete all as specified and as directed

Supply and fixing tubes 'medium grade' galvanised, 15 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing tubes 'medium grade' galvanised, 20 mm bore, ISI marked with all fitting such as bends, tees,elbows, unions,short pieces, connectors, back nuts etc and fixed complete to walls and ceilings or laid in floors, complete all as specified and as directed by Engineer-in-charge.

M&L cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings,steps,cills,sunshades,shelves,lintels etc,and cutting chases for concealed water tubing or concealed conduit wiring,etc,and making good, cutting n.exc 10cm girth in brick walls.

S&F in repair stainless steel lock grating plain/hole size 100 mm dia including embeding in tiles with white cement.

Dismantling PVC/Cement/CI pipes 50 to 110 mm dia including all fittings like bend,branch pieces, connectors, heel rest bend etc and removing from site all as specified and directed

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 110 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

Supply and fixing UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC (SWR), bends for 75 mm bore , complete all as specified and as directed by Engineer-in-charge

Supply and fixing, UPVC (SWR), bends with access door for 75 mm bore , complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR), bends for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC(SWR), bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

Supply and fixing, UPVC branch piece, single (single 'Y') with access door for 75 mm bore complete all as specified and directed.

Supply and fixing, UPVC branch piece, single (single 'Y') with access door for 110 mm bore complete all as specified and directed.

Supply and fixing, UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 75 mm bore, complete all as specified and as directed by Engineer-in-charge

Supply and fixing, UPVC(SWR), junction single, (single 'T') with access door equal or unequal for 110 mm bore , complete all as specified and as directed by Engineer-in-charge

Supply and fixing, UPVC (SWR) , reducers 110 mm dia complete all as specified.

S&F UPVC (SWR) vent cowl 75 mm dia complete all as specified.

Supply and fixing in repair UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F in repair, UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

M&L for 75mm thick cement concrete 1:3:6, type C1, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for repairing of concrete surfaces such as balcony, chajjas, upward or downward facias ,column, pillar, ceiling and similar items with plain cement concrete 1:2:4 type B-0 or rendering 10-15mm thick as per site requirement in CM 1:3 without using extra cement finished even and fair complete all as specified and directed (Up to fourth storey bldgs and including necessory formwork and scaffolding required as per site condition also taking down or dismantling as required at site.

Preparation of new plastered or unplastered surfaces of walls to achieve smooth and even surfaces of walls, chajjas, fascia, face of columns, beams etc. and applying one coat of weather proof exterior emulsion over one coat of wall care putty of 3 mm thick (up to 2nd storey with necessary scaffolding) complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of ceilings to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

Preparation of new plastered or unplastered surfaces of walls to achieve smooth and even surface and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

Material ad labour for preparation of new plastered surfaces of walls & applying two coats of oil bound distemper over one coat of wall care putty of 3 mm thick and one coat of primer complete all as specified.

M&L for applying two coat of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description having width/girth exceeding 10 cm including preparation and rubbing with sand paper to make surface even and smooth complete all as specified.

M&L for applying two coat of synthetic enamel paint on new wooden surfaces of any description over a coat of pink primer having width/girth exceeding 10 cm complete all as specified including preparation and necessary filling by chalk putty as and where requered to make surface even and smooth.

M & L for preparation of old decorated brick /concrete, plastered /un-plastered surfaces of walls, pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of lime white wash on the walls, pillars, cornices etc. complete all as specified and directed.

M & L for preparation of old decorated brick /concrete, plastered /un-plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, oil, greasy spots & rubbing with sand paper and and applying one coat of white wash on ceiling, complete all as specified and directed.

M & L for preparation of old decorated concrete/ plastered surfaces of walls, Pillars, cornices etc by booming down with steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots & rubbing with dustfree sand paper mechanised scrapper as per paint manufacturer specifications and applying two coats of premium oil emulsion distemper over 1 to 2 mm thick wall care putty complete all as directed by Engineer-In-Charge.

Complete removal of existing treatment including washing, rubbing down with sand paper and stopping of painted surfaces including preparation of old plastered surfaces of walls, chajjas, fascia, face of columns, beams etc. and applying one coat of weather proof exterior emulsion making good uneven surface/holes with Birla wall care putty over one coat of primer (up to 2nd storey with necessary scaffolding) complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and not exc 2.00 Sqm each complete all as specified & directed.

M&L 35 mm thick 2nd class hard wood, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply. The size of rail and stile as per IS : 1003 (Part I), complete all as speciied.

S&F in repair aluminium extruded section body, door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.

S&F for powder coated (Powder Coating minimum thickness of powder coating 50 micron) aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F for Powder coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F for Aluminum Power coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified.

Supply and fixing 5.50 mm thick glass sheet ordinary quality Tinted ( approved by Engr-in-Charge/ GE) and glazed in squares, exceeding 0.5 Sqm in each pane.Make:Saint Goblin

Supply and fixing 4mm thick aluminium composite panel (coloured sheet) and in additional other accessories for fitting complete all as specified by Engr-in-Charge.

M&L for preparation of new plastered/concrete surfaces of walls, (up to 4th storey with necessary scaffolding) and applying two coat of cement based paint over one coat of primer complete all as per specified and directed by Engr-in-charge.

Surface excavation n.exc. 30 cm deep and averaging 15 deep and getting out in any type of soil and etc complete all as specified and as directed

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5M in depth for foundation etc and getting out in any type of soil complete all as specified and as directed.

M&L for plain cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregate), as in subbase, mass concrete in foundation, complete all as specified and as directed by Engineer-In-Charge.

Returning filling including spreading, levelling, watering and well ramming in layers n exc. 25cm etc complete.

Earth filling under floor including spreading, levelling, watering and well ramming in layers n exc. 25 cm thick etc complete all as specified and as directed.

Removing excavated material n .exc 50 m and depositing, where directed at a level n. exc 1.5 m above the starting point complete all as specified and as directed.

M&L for RCC 1:2:4 Nominal mix type B1 using 20mm gradded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs, under reamed piles and mass concrete etc complete all as specified and as directed

M&L for RCC 1:2:4 Nominal mix type B1 using 20mm gradded stone aggregate as in Columns, pillars, piers, posts and struts etc complete all as specified and as directed

Ditto all as per item ser No 141 above but as in Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and as directed

Ditto all as per item ser No 141 above but in chajjas etc complete all as specified and as directed

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc complete all as specified and as directed.

Formwork to chullah hoods, chajjas, troughs and similar items including edges etc complete all as specified and as directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns, and stanchions etc complete all as specified and as directed.

M&L TMT bars 8mm dia cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality etc complete all as specified and as directed

Ditto all as per item ser No 148 above but, 5 mm dia and over and incl 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed

Supply only liquid water proofing compound/admixture, ISI marked.

M&L Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-0 (Using 12.50mm graded stone aggregate) as in floor etc complete.

S&F steel Ventilator ( N exc 0.70 Sqm) 1.25 mm thick Box type (Double Shutter) ERW hollow P section of size 60 mm x 25 mm single rebated comprises glazed & wire gauged skelton shutter ERW sec 50 mm x 20 mm and 1 mm thick with two Nos sash bar of T- section 20 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T- section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 four No for each ventilator incl following fitting welded to frame shutter hold fast of 150 mm long of 12 mm x 3 mm FI made to shape 4 No, handle of Z section 20 mm x 25 mm x 100 mm long 1 No per leaf, MS tower bolt 150 mm long 2 No per leaf, Z sec 20 mm x 25 mm, 100 mm long stopper 1 No on per leaf, MS Pintal hinges of size 75 mm x 12 mm 2 No per leaf fabrication, 10 mm Square bar grill, specing of grill 100 mm center to center and fixing arrangement as per drg No CEPZ/TD-324,325/0 (Grill shall be measured separately)

S&F 150mm internal dia, NP-2 RCC drain pipe grade 'A ' laid in trenches laid and jointed complete with collars, with cement joints all as specified & including taking down old pipes, complete all as directed by Enginer-in-charge.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm bore of pipe plain cement concrete 1:3:6 type C-2 (Using 40mm graded stone aggregates)including necessary form work, complete all as specified and directed.

M&L for 75 mm thick plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregates) as in sub base to floors complete, all as specified and as directed by Engr-in-Charge

Material and labour for Cement concrete tiles 30cm x 30cm and 25mm thick, machine pressed; set jointed and pointed in neat cement slurry with grey cement and in floors, and cut and polished , over and including 15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes, complete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B 1 using (20 mm graded aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering slightly rounded or chamfered angles and throating all as specified and direct. Note: Form work required for these items included in the unit rate of this item.

Plain cement concrete 1:3:6 type C-1 (using 20mm graded aggregate) as in surface channel and drain including all necessary form work, complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.complete, all as specified and as directed by Engr-in-Charge.

M&L for Septic tanks, exc in ordinary soil, foundation in PCC 1:2:4 brick work in CM 1:4 slab covers including RCC precast manhole cover having 6mm plate embadded all around / fibre reinforced cover with angle iron frame vent shaft and sludge chamber etc, complete for 10 users.

M&L soakage well exc, in any type of soil, foundation in PCC 1:3:6 wells of honey combed and solidin M-25 concrete, including intercepting chamber brick work in CM, RCC cover slab in M-25 , filling with brick bats, complete of size 2.40 mtr dia x 3.0 mtr deep.

M&L for 100 mm thick PCC 1:4:8 type D-2 ( 40 mm graded aggregate) as in sub base , complete all as specified and directed.

M& L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for Machine pressed precast concrete interlocking paver block wirh grey cement and pigment of any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete,all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and amming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm as specified complete all as specified.

S&F for Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc Fe 410 -W (Gde E- 250) quality complete all as specified and as directed.

S&F structural steel work conforming to Fe-410-W (Gde E-250 Quality-A or B) or Fe-290 Gde E-165, as in roof trusses (framed), purlins, crane gantries, rails, vertical post and fastenings, heavy brackets framing (Beam, tee, angle, channel, squre hollow section or flat section) including distance pieces, cleats etc complete all as specified.

S&F Pre- painted galvatume aluminum zinc(AZ-150 Micron) coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified.

Taking down carefully aluminium conductor point wiring (light, fan, socket, power socket) complete fitting such as swithes, sockets, lamp holder, utility light fitting, fan regulator etc and removing materials from sites and making good distrubed surface of walls and roofs complete all as specified and as directed.

Taking down of unsv MCB DB SPN /TPN along with MCB's

Taking down of unsv Sub main wiring of any size

M & L for complete point wiring with 1.5 Sqmm single core multi stranded copper conductor FRLSH insulated and unsheathed heavy duty cable in colour code including contineous earth wire with cable of size 1.5 sqmm copper conductor flexible FRLSH insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall , plastering after concealing conduit , including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed for the following :- (a) One Light / Fan/ Exhaust Fan point controlled by one, one way switch 6 Amp complete

(b) One 3 pin socket outlet 6 amp independent

(c) One 3 pin socket outlet 6 amp same board

(d) One bell/ buzzer point controlled by one, complete all as specified and directed.

(e) One light point controlled by one, Two Way Switch complete all as specified and directed.

All as per srl item No 173 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Supply and fix modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type switch, Two way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Supply and fix modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Supply and fix modular type fan regulator step down 120 Watt, 2 module complete all as specified and directed.

Supply and fix ceiling rose surface, backelite, three terminal, 240 volts complete all as specified and directed.

Supply and fix modular bell push with indicator polycarbonate materials ISI markrd 1 module, 6 Amps 240 Volts.

Supply and fix musical door bell, AC 230 Volts single phase.

Supply and fix LED light fitting 1 x 18Watt, 220V, AC decorative box type with driver, holder including LED Tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete with all fixing arrengenment all as directed by Engr in chage. Note:- The LED batten and LED tube rod shall be of same make.

Supply and fix of lamp holder,PVC /Polycarbonate type with back plate for batten fitting .

Supply and fix LED lamp suitable for B22 holder of capacity 10 Watt.

Supply and fix energy saving new generation 10W LED IP65 bulk head luminaire with opal diffuser complete all as specified and directed.

Supply and fix Distribution Board (SPN) double door 8 Way and should be IP 43 protected with Copper Bus bar 100 Amp rated ,Earth Bar ,neutral Bar Door Earthing.

Supply and fix MCB SPN complete 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed.

Supply and fix MCB Single pole 6 to 32 Amp with rupturing capacity 10 KA 'C' series, complete all as specified and directed

Supply and fix sub main wiring with single core cable 2x 10 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 10 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fix sub main wiring with single core cable 2x 4 sq mm FRLSH insulated Unsheathed stranded copper conductor cable 1100 Volts grade in rigid PVC conduit (Concealed) medium grade alongwith 1 x 4 Sq mm FRLSH insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including chesing, cutting & making good to match with the existing surface complete all as specified and directed.

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps 240 volts complete all as specified and directed.

Taking down and refixing of Ceiling fan / Exhaust Fan any size/sweep, including oiling, Greasing and cleaning and applying two coats of synthetic enameled paint after preparation of surface complete over a coat of primer, all as specified and directed by Engr-in-charge.

Supply and fix of exhaust fan, steel body AC single phase. 230 V of size 300 mm sweep with, blades, and frame and louvers and including making of holes in wall, floor etc all as directed by Engr in charge.

Taking down the existing electric meter of any capacity and make after disconnecting electrically, carry out the cleaning and refixing, reconnecting including applying one coat of paint on existing MS box of electric meter, testing in all respect for smooth running completeall as directed.

Taking down carefully after disconnecting electrical & water supply connections of storage type electric water heaters (Geysers) of capacity 25 liters of any make/type and refixing on its original/New position and reconnecting electric and water supply connections including replacement of nuts, bolts, washers, fastners etc and testing complete all as directed.

M & L for complete earthing with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with XPM weighing not less than 1.87 kg/Sqm with suitable handle made of 12mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 7.5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion.

Supply and fix Vertical Distribution Board (VTP&N) 4 way double door suitable for and including MCCB four pole as incomer and out going MCBs and should be IP 43 protected with Copper BusBars, Neutral Links, Earthing bar all as specified and directed. Note:- (i) MCCBs FP & SP shall be measured paid separately (ii) MCB & DB shall have the same make.

Supply and fix 4 Pole MCCB 100 Amp, 415 Volts with rupturing capacity 16 KA , complete all as specified and directed

Supply, laying for replacement of unserviciable underground LT cable 1100 Volts grade heavy duty electric cable XLPE insulated & PVC outer sheathing with aluminium stranded conductor, Armoured cable 50 sq mm 3.5 core cable confirming to IS-7098 Part-I (1988) with latest ammendments.

Supply & laying dry river sand as cable cushioning 15cm thick layer before laying and 8cm thick over cable after laying the cable in trench complete all as specifieds and directed.

Supply & laying dry bricks over cable as mechanical protection layed flat with width equal to length of brick with sub class 'B' bricks complete all as specifieds and directed.

Material and labour for GI pipe ''light grade'' for road crossing / on wall / on pole with fixed clamps, nuts, bolts for cable protection of size 40 mm dia complete all as specifieds and directed.

M & L Point wiring complete with 1.5 sqmm single core PVC insulated and unsheathed cable 1100 volts, FRLS grade with multistranded copper conductor ISI marked drawn through heavy duty PVC concealed conduit fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm stranded copper conductor cable as earth continuity conductor and connected to common earth dolly, including concealed MS box with 3 mm thick laminated sheet cover fixed with brass screws and cup washers for mounting of plate mounting for housing the switches, socket outlets, fan regulators etc, all as specified and as directed . (a) One Light / Exhaust Fan point controlled by one, one way switch 6 Amp complete

(b) One 3 pin socket outlet 6 amp independent

(c) One 3 pin socket outlet 6 amp same board

All as per srl item No 209 above but for one 3 pin socket outlet 16 Amp independent with cable of size 2.5 Sqmm for point wiring and 2.5 sqmm as in continuous earth wire.

Supply and fix switch piano, flush type single pole, one way 5 Amps capacity

Supply and fix socket out let 2 in 1, 5 Pin, 6A combined 2 module

Supply and fix switch piano, flush type single pole, one way 15 Amps capacity

Supply and fix socket out let 2 in 1, 5 Pin, 16A combined 2 module

Supply and fix Distribution Board (SPN) double door 4 Way and should be IP 43 protected with Copper Bus bar 100 Amp rated ,Earth Bar ,neutral Bar Door Earthing.

Supply & laying or fixing or passing through pipe 1100 volts grade heavy duty cable with XLPE insulated aluminium mult strand conductor served with an inner sheathing of PVC tape armoured with galvanized steel wire or tape and overall XLPE sheathing 16 Sqmm 2 Core nominal cross section complete all as directed by Engr-in-Charge.

Supply and lay pipe Galvanized, " Medium grade", including all type of fitting 25 mm dia all as directed by Engr In Charge.

Supply and fix of Gun metal gate valves with iron wheel head, screwed both ends for iron pipes complete, size of GM gate valve 25 mm all as directed by Engr In Charge.

M&L of drilling and tapping cast iron / Ductile iron water mains (in position) for branch connections of the internal dia 20 mm (for providing straight plain brass ferrules or connection screws) all as directed by Engr In Charge.

M&L Construction of brick masonry valve pit of size 120cmx120cmx120cm (internal dimension of chamber) with brick work in cement mortar 1:4 including plastering internally and pointing externally as the work proceeds complete with MS sheet cover 3.15mm thick and angle iron frame 40mmX40mmX6mm with handle, locking arangement and painting with two coats of synthetic enamelled paint over a coat of red oxide primer on steel surfaces including earth work & excavation in any type of soil, disposal of surplus spoil not exceeding 50m complete all as specified and shown on drawing.

M/S RAKESH CONSTRUCTION

M/S SHUBAM ENGINEERS

J P TECHNO

M/s Singh Constructions