Estimate for Construction of Control room cum field office near Emergency Gate Shafts area at RSD Project.

Amount

Dismantling of Cement concrete plain 1:3:6 mix

Dismantling of Reinforced cement concrete

Earth work in excavation of foundations of bridges culverts, building including handling of materials with combined lead of 15 metres dressing of bed and sides stacking the excavated soil clear from the edge of excavation and subsequent filling around, For semi conglomerate or soil of nature of pick jumper.

Cement Concrete 1:4:8 with stone aggregate 40mm gauge mixing by mechanical means using concrete mixer volumetric type.

First class burnt brick work laid in cement sand mortar 1:4 in foundation and plinth.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centering and shuttering in foundation and plinth

First class burnt brick work laid in cement sand mortar 1:4 in first storey up to 4 meters above plinth level.

Extra for brick tile masonry in additional story up to 4 mtr above the top of the structural roof of the lower story.

Shuttering for faces of concrete foundations and foundation beam & plinth beam (vertical or battering)

Centering and shuttering for columns (Square or rectangular or polygonal in plain)

Centering and shuttering for sides and soffits of beam, beams launchings girders bressumers, lintels

Centering and shuttering for flat surfaces such as suspended floors, roofs, landings, chajjas, shelves etc.

Reinforced cement concrete M-20 mechanically batch mixed using batch type concrete mixer as per IS: 1791 and vibrated by needle vibrator but excluding steel Reinforcement centering and shuttering in superstructure.

Cold twisted deformed (Ribbed/ Tor Steel Bar) Bars Fe 500 grade as per IS 1786-2008, for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete

20 mm thick cement plaster 1:4 in two coat work

Cement rendering on plaster 1mm thick

10mm thick cement plaster 1:4

Cement rendering on plaster 1mm thick

Preparation of plastered or concrete surface for painting (including sand papering the surface) using ready mixed cement based wall putty by applying two coats to get required finish.

Wall painting with plastic emulsion paint of approved brand and manufacturer to give an even shade (two or more coats)

Dholpur stone tile 25 mm thick in wall facing (lining) laid in any pattern as specified on 20 mm thick cement sand plaster 1:4 and jointed with neat cement slury mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, pins and dowels etc.

Cement concrete 1:5:10 with stone aggregate 40 mm gauge mixing by mechanical means using mixer volumetric type.

Marble stone flooring with 18-20mm thick marble stone as per sample of marble approved by Engineer-in-charge, over 20 mm(average) thick base of cement mortar 1:4(1 cement :4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with: Slabs Sizes above 0.50 Sqm

Marble work of thickness 18-20 mm for wall lining (veneer work), backing filled with a grout of average 12mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including pointing with white cement mortar 1:2 (1 white cement :2 marble dust) with an admixture of pigment to match the marble shade (To be secured to the backing by means of cramps, which shall be paid for separately). Makrana doongri adonga veined and chack doongri with gray stretches. Slabs Sizes above 0.50 Sqm.

Black Granite stone tiles 15-20mm thick in skirting, risers of steps, dado walls and pillars laid in 12.5mm thick cement mortar 1:3 (1 cement 3 coarse sand) and jointed with neat cement slurry mixed with pigment to match the shade of stone, including rubbing and polishing including labour for fixing dowel pins and ramps.

Providing and laying vitrified floor tiles in different sizes in light color shades made using full body technology thickness to be specified by the manufactured with water absorption less than0.08% and conforming to IS: 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 fine sand) complete. (full body vitrified tiles have pigment in entire body/thickness of tile which makes chips and scratches less noticeable and make na ideal choice for high traffic zones) Size 600 x 600 mm.

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M-35 grade manufactured by block making machine equipped with steel mould clamped to a strong vibratory table with hydraulic pressure for compaction of concrete as per IRC SP 63-2014 and of approved size and design / shape laid in gray Colour and pattern over and including 40 mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge.

Providing and applying Anti Termite Treatment using pre constructional chemical treatment measures as per IS - 6313 – 2001 ( Part 2 ) & using Chemical containing chloropyrifos systemic insecticide diluted to manufacturer's specifications (i) In foundation pits, by treating the bottom & sides up to height of 300mm by uniformly spraying solution @ 5 Litre / sqm (ii) In the refill earth on both sides of all built up walls @ 7.5 Litre / Running meter (width - 300mm,depth - 450 mm) (iii) Before laying the floor, by uniformly sprinkling the top surface of the consolidated earth within the outer perimeter @ 5 Litre solution per sqm.

Providing and fixing aluminum work for doors, windows, ventilators and artitions with extruded built up standard tubular sections/appropriate z-sections and other sections conforming to Is: 733 and IS : 1285 of Jindal, Hindalco, Mahavir or equivalent make approved by Engineer in Charge , fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides wither quired PVC Plug/neoprene felt etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/stainless steel screws, all complete as per architectural drawings and the directions of Engineer-In-Charge. (Glazing and paneling to be paid for separately)For fixed portion and chaukhats

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC Plug/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item)Float glass panes of 5 mm thickness

Wire gauge fixed on Chowkats with 25mm thick Golden Champ wood cover molding of full width.

Providing and fixing hydraulic door closer ISI mark with necessary screw etc. Complete I.S.I Designation No. II (size of door 701mm to 850mm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece MS sheet outer box with slide plate and with stainless steel cover plate etc. complete as per the direction of Engineer-in-charge.

Providing and fixing bright finished brass 100mm mortise latch and lock with 6 levers and a pair of lever handles with necessary screws etc. complete (best make of approved quality).

Providing and fixing 12mm thick 150mm wide pelmets with 25mm dia Aluminium rod and brackets including fixing with 25mmx3mm MS Flat 10cm long and PVC Plug etc complete (using Kail wood)

Cost of Aluminium fittings complete for doors, windows such as tower bolts, handless, stopper sand screw etc. for these fittings (Excluding sliding bolt)for shutter area above 0.50 Sqm

Providing and fixing in position Chinaware extended wall mounted E.W.C type suite (size 66x46x77.5cm) with P trap or S trap of approved make (to the approval of the Engineer-in-charge) with or without 10 ltr. Chinaware matching flushing cistern and seat cover complete in all respect and to the entire satisfaction of engineer in charge. Chinaware extended wall mounted E W.C. with matching chinaware cistern and seat cover complete in all respect.

Providing and fixing jet spray with 2'-6" long PVC pipe. With C.P. Brass nut

Providing and fixing in position vitreous chinaware white lavatory suites of approved make (to the approval of the Engineer-in-charge) consisting of C.P. brass waste 32mm dia with one C.P. brass pillar tap including Rack Bolt screw pair 115mm long complete in all respect. Size 630mm x 450mm x 850mm

Providing and fixing in position C.P brass basin mixer without pop-up waste up system 450 mm long flexible houge of approved make (to the approval of the Engineer-in-charge) complete in all respect.

Providing and fixing vitreous chinaware pedestal of approved make (to be approved of Engineer-in-charge) for wash basin complete in all respect. Vitreous chinaware standard white pedestal for wash basin.

Providing and fixing in position stainless steel sinks of approved make (to the approval of Engineer-In-Charge) 1 mm thick grade 304 (18/8) with waste coupling complete in all respect. Rectangular sink with deluxe border single bowl overall Size 700 mm x555 mm x 230 mm

Providing and fixing in position C.P Brass bottle trap 32mm dia with 40mm seal of approved make (to the approval of the Engineer-in-charge) complete in all respect.

Providing and fixing in position 32 mm dia G.I waste pipe embedded in wall upto floor level including cost of fittings complete as required by the Engineer in charge.

Providing and fixing in position paper holders of approved make (to the approval of Engineer-In-Charge) fixed in to wall with C.P brass screws complete in all respects. C.P brass toilet paper holder

Providing and fixing in position towel rails /ring of approved make (to the approval of Engineer-In-Charge) fixed in with rawl plugs embedded in walls with brass screws, complete in all respects. C.P. brass towel Rails size 15mm dia 610 mm long

Providing and fixing in position CP acrylic shelf with C.P bracket and guard rails of approved make (to the approval of Engineer-In-Charge) fixed in with rawl plugs and CP brass screws complete in all respect. C.P. brass glass corner with rail 8mm thickness and height 250 mm

Providing and fixing in position C.P Brass soap dish of approved make (to the approval of Engineer-In-Charge) fixed into wall with rawl plugs and C.P brass screws complete in all respects.

Providing & Fixing in position 5mm thick beveled edge mirror of superior glass (of approved make) complete with 4mm thick hardboard backing fixed in with rawl plugs 50mm , CP brass screws and washers and S/S studs on top complete in all respect (As required by the Engineer-in-Charge). Size 600mmx450mm

Providing & fixing in position 15 mm i/d bib cock of approved make (to the approval of Engineer-In-Charge) complete in all respect. C.P. brass Bib cock long nose/Long body foam flow without flange.

Providing & fixing in position stop cock / Angle valve of approved make (to the approval of Engineer-In-Charge) complete in all respect. C.P. brass 15mm Concealed stop cock with flange.

Providing & Fixing in position liquid soap container of approved make (to the approval of Engineer-In-Charge) complete in all respect. C.P. brass liquid soap container.

Providing and fixing in position H.C.I. soil waste vent or antisyphonage pipes to I.S.I. specification of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of lead jointing.100mm i/d H.C.I. Pipe lines laid complete

Providing and fixing in position C.I. gully trap cover weighing approximately 7.26 kg and frame for gully trap chamber clear opening size 300mm x 300mm and outside size 330mmx330mm including painting the exposed surface with 3 coats of black bitumastic superior paint of approved manufacture etc

Providing and fixing in position gratings 150 mm x 150mm for gully trap. H.C.I. grating including painting with black bitumastic superior paint of approved manufacture three coats.

Providing lead caulked joints to H.C.I. pipes and specials conforming to I.S.I. Specification of E.L.C. manufacture or any other reputed firm including cost of lead yarn, fuel and tools etc.100mm i/d (1.36 kg.)

Providing & Fixing in position M.S or heavy flat iron clamps made out of M.S flat iron not less than 5 mm of the approved design for fixing C.I. soil waste, vent or antisyhonage pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting. M.S. Holder bats clamps for 100mm i/d H.C.I. pipes

Providing and fixing centrifugally cast iron Floor traps conforming to I.S.I. Specification(IS:3989) of approval make(to the approval of Engineer-In-charge) of the self-cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under and around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors, etc. minimum depth of water should be 150mm with a minimum seal 50mm.With 100mm x 75mm i/d 600mm long

Cutting chase in brick walls in cement or in floor for embedding G.I. or C.I pipes lines and making good the same to its original condition. Size 75 mm x 75 mm

Providing &placing in position on terrace (at all floor levels ) HDPE water storage tanks of make (to the approval of the Engineer-in-charge) with cover with suitable locking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and base support for tank. Triple layer tanks.

Providing and fixing in position storage type automatic electric water heater pressure / non pressure type thermostatically controlled, single phase, vertical wall mounting of approved make (To the approval of Engineer-in- Charge) with thermostats inner container of stainless steel complete with 1Mtr. 3 core flexible cord with plug and non-return valve pressure release valve complete including fixing and testing complete in all respect.(as required by the Engineer-in-Charge) 25 litre capacity water heater

Terracing consisting of tiles 22.86 Cm x 11.43 Cm x 3.83 Cm laid over 25mm mud plaster 7.5 Cm mud filling on another layer of 25mm mud plaster including two coats of bitumen laid hot at 1.65 Kg /Sqm top of RCC Slab including grouting with cement sand mortor 1:4 and top surface to be left clean after wire brushing.

Providing and fixing cast iron 100mm dia, rain water pipe with screw and wooden plugs fixed and wall-face, including filling joints with spun yarn and cement mortar 1:2 excluding head and shoe etc.

Providing and fixing cast iron head for rain water pipe on wooden plugs fixed on wall-face including filling the joints with spun yarn and cement mortar 1:2.

Providing and fixing cast iron shoe for rain water pipe on wooden plugs fixed on wall face including filling the joints with spun yarn and cement mortar 1:2.

Top khurra 0.6m x 0.6m for rain water pipe in 25mm thick cement concrete 1:2:4 over 50.00 thick cement concrete 1:8:16.

Khurra on roof as per item No. 13.43 with CI Spouts 100 mm dia fixed in position.

Bottom Khurra on ground 1.2m x 0.6m consisting of brick on-edge laid in cement mortar 1:3 over 7.5cm cement concrete 1:8:16 including 12.5mm thick cement plaster 1:3

Cement concrete 1:2:4 gola 10cm x 10cm concave quadrant along junction of roofs with parapet wall finished smooth, where specially specified.

Providing and laying, jointing fixing and testing ISI marked G.I. Pipe(as per IS 1239) B-Class including cost of specials (such as tees, bends, sockets, elbows etc.)Painting with anticorrosive bitumastic paint, testing, cutting, threading Inside building complete. 15 mm i/d

Providing and laying, jointing fixing and testing ISI marked G.I. Pipe(as per IS 1239) B-Class including cost of specials (such as tees, bends, sockets, elbows etc.)Painting with anticorrosive bitumastic paint, testing, cutting, threading Inside building complete. 20 mm i/d

Providing and laying, jointing fixing and testing ISI marked G.I. Pipe(as per IS 1239) B-Class including cost of specials (such as tees, bends, sockets, elbows etc.)Painting with anticorrosive bitumastic paint, testing, cutting, threading Inside building complete. 25 mm i/d

Making connection with the existing G.I. branch main up to 40 mm size pipe including cutting of existing pipe line, threading of pipe lines from both ends and fixing G.I Tee etc. in the pipe line (including cost of G.I tee) complete in all respects.

Providing, lowering, cutting & jointing salt Glazed Stone ware Pipes and Specials ISI marked as per IS 651-2007 class Sp-1 into Trenches for all depth sand Laying out the same to correct alignment, Gradients, levels etc., concrete beds and joint holes, supporting the pipes and specials, in correct position in a suitable rigid manner while the same are being jointed and until the surrounding benching, haunching and envelopes are completed including jointing of pipes and special in trenches, using cement sand mortar 1:1 and best spun jute yarn as per IS: 1887, finishing and trowelling of each joint at an angle of 45degree with the longitudinal axes of pipe, watering, keeping the joint covered and wetted till the same are cured, testing the sewerage line for leakage and making all leakage and defects good as laid in the contract specification, chipping and finishing the cut surface to uniform finish to the entire satisfaction of Engineer-in-charge Including all cartage etc. complete in all respect. 200 mm i/dia Pipes

Constructing brick masonry manhole in cement mortar 1:5 ( 1 cement : 5 coarse sand ) with R.C.C. core wall between machinery, RCC top slab 20mm thick using M-20 mix, foundation concrete 1:4:8 mix (1 cement: 4coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement: 3 coarse sand) finished with floating coat of neat cement and making benching in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, Orange colored PVC steps including RCC cover with frame internal dimensions complete as per standard design.(in water logged area), Inside size 90x150 cm and 120 cm deep

Construction of brick masonry inspection chambers size as given below upto0.60 m average depth in 1:5 cement sand mortar, C.C 1:4:8 (150mm thick) in foundation cement concrete 1:2:4 benching 12.50mm thick cement plaster 1:2 with a floating coat of 1mm thick of neat cement, R.C.C. 1:2:4 slabs 100mm thick cement concrete topping 50mm thick with 455mm x 455mm, 455mm x 610mm inside R.C.C inspection chamber cover and frame (Weight as per I.S.I specifications) painted with 3 coats of black bitumastic paint conforming to I.S.I complete as per standard design. 450mm x 600mm inside with 455mm x 610mm cover and frame light duty double seal.

Earth filling under floors with surplus soil containing more than 40% gravel or kankar excavated from foundation and taken only from outside the building plinth in 15 cm layers including ramming, watering and consolidating lead upto 30 metres.

Disposal of dismantled muck from site of work to disposal site with an av. Lead of 1KM including loading /Unloading, leveling and carriage to disposal site complete in all respects.

Earth filling under floors with surplus soil containing more than 40% taking outside the premises in 15 cm layers including ramming watering and consolidated lead upto 1000 metres

Providing and Fixing ceiling consisting of12.5mm thick Gypsum Board of any size GI Cradling hanged from the ceiling by means of GI hanger complete as per drawings, specifications and to the entire satisfaction of engineer-in-charge.

Providing & fixing kitchen cabinet including all fittings for sliding system, drawers, shutters and taxes etc complete as per departmental design and requirements.

Providing & framing toughened glass 12 mm thick in windows including frame work silicon solvent with finching and labour.

Providing & fixing 16 gauge stainless steel pipe railing of grade 304 duly fixed on steps with the help of bolts grouted on steps with hand rail and newel post of 50mm dia Stainless steel pipe, Balusters of 40mm dia Stainless steel pipe and guard 3 Nos of 15mm dia Stainless Steel pipe complete in all respect

The Jandriya Mohalla Co op L/C Society Ltd.

Dhotra Construction Company

Ashok Kumar Govt Contractor