RFQ 11111 Renovation of Canteen at Kolihan Mines Area

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Applying priming coat :With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

Applying priming coat :With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works

Finishing walls with water proofing cement paint of required shade :Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

WHITE WASHING WITH LIME TO GIVE AN EVEN SHADE: OLD WORK ( ONE OR MORE COAT ) WITH LIME

20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)

6 mm cement plaster of mix :1:3 (1 cement: 3 fine sand)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

R.C.C. work in walls,includ attached pilasters,buttresses, plinth and string courses,fillets,columns,pillars,piers,abutments, posts and struts etc.up to floor five level excluding cost of centering, shuttering, finishing and reinforcement

Centering and shuttering including strutting, propping etc. and removal of form for : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform.

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Cold twisted bars

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.1:3:6 or richer mix

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge:In cement mortar

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift up

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at plinth level with :Cement mortar 1:6 (1

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm. top diameter, 160 mm bottom diameter an

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With F.P.S. bricks

STONE SOLING UNDER FLOOR INCLUDING FILLING VOIDS WITH STONE CHIPS AND SAND, RAMMING, WATERING AND CONSOLIDATING ETC. COMPLETE

Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:4 (1 cement : 4 coarse sand)

Half brick masonry with F.P.S. bricks of class designation 75 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Carriage of material by mechanical transport including loading, unloading and stacking:Lime, moorum, building rubbish:Lead 1 KM.

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work15 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work20 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work25 mm dia. nominal bore

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device,conforming to IS : 7231.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. b

Providing and fixing soil, waste and vent pipes : 100 mm dia.Sand cast iron S&S pipe as per IS: 1729.

PROVIDING AND FIXING 75 M.M. DIAMETER C.I. PIPE

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outletSand cast iron

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100 mmSand cast iron S&S as per IS - 1729

Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms

Providing and fixing brass stop cock of approved quality :15 mm nominal bore

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Flexible pipe32 mm dia

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length15 mm nominal bore

PROVIDING AND FIXING 500 LITRES CAPACITY SINTEX OR EQUIVALENT MAKE WATER TANK

PROVIDING AND FIXING FOUR LAYER 1000 LITRES CAPACITY PVC WATER TANK WITH TANK NIPPLE AND BRASS FLOAT VALVE COMPLETE

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by EIC

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved s

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

PROVIDING AND FIXING OXIDISED M.S. SLIDING DOOR BOLTS WITH NUTS AND SCREWS ETC. COMPLETE. 300*16 MM.

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm

PROVIDING AND FIXING OXIDISED M.S. TOWER BOLT (BARREL TYPE) WITH NECESSARY SCREWS ETC. COMPLETE: 150*10 MM.

PROVIDING AND FIXING FLY PROOF GALVANISED M.S. WIRE GAUZE TO WINDOWS AND CLERESTORY WINDOWS INCLUDING 62*19 MM BEADING OF SECOND CLASS TEAK WOOD. WITH AVERAGE WIDTH OF

REMENING GLASS PANES, WITH PUTTY AND NAILS WHEREVER NECESSARY: GLASS PANES WEIGHTING 7.5 KG/SQM

RENEWING GLASS PANES, WITH WOODEN FILLETS WHEREVER NECESSARY: GLASS PANES WEIGHING 10 KG/SQM

PROVIDING AND FIXING KAIL WOOD CHAMFERRED EDGE WOODEN BEADING 65X12 MM WITH M.S.SCREWS ETC.

PROVIDING AND FIXING PANELLED OR PANELLED AND GLAZED SHUTTER FOR DOORS, WINDOWS AND CLERESTORY WINDOWS INCLUDING BLACK ENAMELLED M.S. BUT HINGES WITH NECESSARY SCREWS. SECOND CLASS KAIL WOOD(35 MM THICK).

DISMANTLING WOODEN PARTITION WALL INCLUDING FRAME WORK, COMMERCIAL PLY, DOOR SHUTTER WITH BUTT HINGES, WOODEN BEADING ETC. COMPLETE, AS PER DIRECTION OF ENGINEER IN- CHARGE. LABOUR RATE ONLY

PROVIDING AND FIXING CIMMERCIAL PLY WOOD 6 MM THICK AS PER DIRECTIONS OF ENGINEER IN-CHARGE

PROVIDING WOOD WORK IN FRAMES OF FALSE CEILING, PARTITIONS ETC. SAWN AND PUT UP IN POSITION : SAL WOOD

P&F Precoated G.I profile /Trapezoidal profile sheets 0.50 mm (0.05%)TCT zinc coating 120 grams per sqm, in 240mpa steel grade, 5-7 microns epoxy primer & polyster top coating 15-18 micron, self drilling/ tapping screws (5.5-8x55mm)

P/F precoated galvanised steel sheets roofing accessories 0.50 mm(+0.50%) thickness. Zinc coating 120 grams per sqm, 240 mpa steel grade 5-7 microns epoxy primer and polyster top coat 15-18 microns .(A) Ridges plain(500-600 mm)

DISMANTLING ROOFING INCLUDING RIDGES, HIP VALLEYS AND GUTTERS ETC. AND DEPOSITING THE SERVICABLE MATERIALS IN CENTRAL/SITE STORES AND INCLUDING DISPOSAL OF UNSERVICABLE MATERIALS WITHIN 50 M LEAD AS PER DIRECTION OF ENGINEER IN CHARGE. ASB