138WE/L-116/2025-26

Amount

M&L for excavation in trenches, not exc. 1.5m wide and not exc. 1.5m in depth; for foundation, etc. or for laying UG cable in trenches not exc 10sqm on plan and not exc 1.5 m in depth in hard/dense soil and getting out complete all as specified and/or as directed by Engr-in-Charge.

Returning, filling in (soil), including spreading, levelling, watering and well ramming in layers not exc. 25cm, complete all as specified and/or as directed by Engr-in-Charge.

Removing excavated material to a distance not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point, complete all as specified and/or as directed by Engr-in-Charge.

M&L for Sand cushioning to under ground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Part-I, 2009. Note : Punned thickness only will be measured and paid.

Supply and laying of factory made, machine pressed, unreinforced, precast concrete cable cover class LV type-2 flat size 250 mm x 150 mm x 40mm, complete all as specified and directed

M&L PCC 1:4:8, type D2, using 40 mm graded stone aggregate as in foundation, filling, or mass concrete complete all as specified and/or as directed by Engr-in-Charge.

Material and Labour precast cement concrete 1:3:6 type C-1 (20mm graded crushed stone aggregate) as in block masonry with solid blocks, exc.10cm in width and set in cement mortar 1:6, complete all as specified and/or directed by Engr-in-Charge.

Material and labour for cement concrete in foundation, filling and mass concrete 1:2:4 type B2 with using 40mm graded stone aggregate, complete all as specified and/or directed by Engr-in-Charge.

Supply and laying of XLPE insulated, armoured, heavy duty electric cables (heavy duty) with stranded aluminium conductor rating 1100 volts grade of size 120 Sqmm 3.5 core laid in trenches or passing through pipes, ducts or fixed to walls/ poles including taking down existing old cables and cable covers complete all as specified and/or directed by Engr-in-Charge.

All as per serial item No. 09 above, but cables of size 70 Sqmm 3.5 core.

All as per serial item No. 09 above, but cables of size 50 Sqmm 3.5 core.

All as per serial item No. 09 above, but cables of size 35 Sqmm 3.5 core.

All as per serial item No. 09 above, but cables of size 16 Sqmm 2 core.

All as per serial item No. 09 above, but cables of size 10 Sqmm 2 core.

All as per serial item No. 09 above, but cables of size 25 Sqmm 2 core.

All as per serial item No. 09 above, but cables of size 16 Sqmm 2 core.

All as per serial item No. 09 above, but cables of size 10 Sqmm 2 core.

Taking down old unserviceable feeder pillar box and supply and fix feeder pillar box of suitable size with incommer MCCB of capacity 160 Amps, 415V , with 4 Nos aluminium bus bar strip along with 14 Nos MCB SPN 63 Amps, 240 Volts, C type with din rail for mounting and necessary wiring for MCBs complete all as specified and/or directed by Engr-in-Charge.

S&F in replacement 4 way double door TPN vertical load line distribution board suitable for flush mounting and surface mounting with 250 Amps bus bar with neutral bar and earth including MCCB 100 Amps, TPN, 25 KA as incomer and making good the disturbed surfaces of walls, floors etc. complete all as specified and/or directed by Engr-in-Charge.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 08 Ways complete all as specified and/or directed by Engr-in-Charge.

Supply and fix in replacement of sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 12 Ways complete all as specified and/or directed by Engr-in-Charge.

Supply and fix MCB SPN 63 Amp 240 Volts AC ISI marked complete all as specified and/or directed by Engr-in-Charge.

Supply and fix MCB SP 6-32 Amps. 240 Volts 50 HZ complete all as specified and/or directed by Engr-in-Charge.

Taking down old unserviceable feeder pillar box and supply and fix feeder pillar box of suitable size with incommer MCCB of capacity 125 Amps, 415V, with 4 Nos aluminium bus bar strip along with 14 Nos MCB SPN 63 Amps, 240 Volts, C type with Din rail for mounting and necessary wiring for MCBs complete all as specified and/or directed by Engr-in-Charge.

Taking down old unserviceable feeder pillar box and supply and fix feeder pillar box of suitable size with incommer MCCB of capacity 100 Amps, 415V, with 4 Nos aluminium bus bar strip along with 14 Nos MCB SPN 63 Amps, 240 Volts, C type with Din rail for mounting and necessary wiring for MCB,s complete all as specified and/or directed by Engr-in-Charge.

Supply & fix in replacement of tubes light grade of size 80 mm bore galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and/or directed by Engr-in-Charge.

Supply & fix in replacement of tubes light grade of size 50 mm bore galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and/or directed by Engr-in-Charge.

Supply and fix in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type (Warm White) with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and/or directed by Engr-in-Charge.

Supply and fix in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC surface mount type (Cool White) with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and/or directed by Engr-in-Charge.

S&F in replacement of LED single tube light fitting surface / pendent mounting complete with batten for LED tube light 20 Watt LED Cool white with, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver, complete all as specified and/or directed by Engr-in-Charge.

Supply and fix in replacement of Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground to a depth not less than 2.25 mtrs deep below normal ground level with top edge of earth plate not less than 1,5 ntrs below normal ground level connected to galvanised iron strip 32 x 6mm as earthing leads by means of galvanised bolts, nuts, check nuts and washer of galvanised iron or steel complete with 20 mm dia GI Pipe light grade for watering and 40mm dia GI light grade pipe for protection of strip up to test point including test point of strip 50x50x3mm GI, charcoal dust, common salt 15cm all around the earth plate all as shown in electric plate No.3 of MES SSR Part-I all as specified or indicated and testing on completion including necessary excavation, earth work PCC pit and with RCC cover of suitable size water funnel with wire mesh complete all as specified and/or directed by Engr-in-Charge.

Taking down old unserviceable street light fitting and supply and fix street light fitting 35 watt 230 Volt AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP65/66 protection complete all as specified and/or directed by Engr-in-Charge.

Supply and fix in replacement LED flood light fitting 120 watt 230V AC outdoor type with thermal management in multiple optics and equipped with IP 66 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and/or directed by Engr-in-Charge.

Dismantling old unsv and supply and fix of cross arms bracing support clamps, back plates fabricated from steel section made out of Fe-0-310/Fe-0-410 including nuts, bolts and washers welding, drilling hole complete with two coats of aluminium paint over one coat of primer complete all as specified and/or directed by Engr-in-Charge.

S&F in replacement of ACSR conductor any size drawn straight horizontal on over head lines on existing poles including binding with insulators. Weight of conductor shall be measured straight horizontal distance between centre of two adjacent poles and calculating weight of conductor of size and length by adding 3% extra for sag, jointing jumpers, etc. complete all as specified and directed by Engr-in-Charge.

S&F in replacement of pin insulator porcelain white, brown or green 100 mm height, 65 mm dia for 1100 volts grade complete all as specified and directed by Engr -in-charge.

S&F in replacement of galvanized steel wire 4mm dia for continuous earth wire complete all as specified and directed by Engr-in-Charge.

S&F PVC Spacer 2/4 way for LT over head line 1100 V complete all as specified and directed by Engr-in-Chage.

S&F in replacement of stay assembly complete with stay plate bow, stay rod of dia 16mm and galvanised iron stay wire stranded of size 7/4mm and accessories as shown in electric plate No 1 of SSR part-I complete all as specified and/or directed by Engr-in-Chage. Note:- (loop type insulator, stay clamps, excavation and concrete shall be measured separately)

Dismantling old unsv poles and supply and fix Steel tubular swaged street light poles complete with pole arms 1.2 m & cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP-31 9.0 mtr long and painting with two coats of aluminium paint over one coat of primer on exposed surface of pole all as specified and directed by Engr-in-Charge. ( Note- Excavation & PCC will be measured and paid separately)

M&L for painting of steel poles 9 mtr including cross arms, clamp of any length and shape for LT OH line with 2 coats of aluminium paints including preparation of old surfaces and marking pole numbers 15 cm dia yellow circle and marking 3 bends width 30 cm by synthetic enamel paint from bottom of pole to 1.5 mtr heigth complete all as specified and as directed by Eng-in-charge.

All as per Srl item No 43 above, but 2 pole structure steel tubular HT poles.

All as per Srl item No 43 above, but 4 pole structure steel tubular HT poles.

Supply and fix Square LED luminaire 300mm x 1200mm, 24W, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof/ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in- Charge.

Material & labour for earthing with Galvanised Steel earth plate electrode 60cm x 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised Iron wire 4 mm as earthing lead (up to terminal point) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 of SSR 1991(Part-I) including taking out old unserviceable earthing complete all as specified and directed. NOTE : - The rates for earth work, GI protection pipe, funnel, wire wash, CI cover, etc. shall be deemed to be included in quoted rates of this item.

Supply and fix cable jointing STRAIGHT THROUGH JOINT for 1100V grade cable complete with Jointing material (Heat shrinkable) and accessories suitable for 3.5 core XLPE armoured, aluminium conductor cable of size up to 70 sq mm complete all as specified and/or as directed by Engr-in- Charge.

Disconnecting and taking out the voltage stabilizer of following capacity up to 250 KVA any description and of any make, dismantling/ opening of the voltage stabilizer of following capacity, three phase, AC 415 Volts, for Maintenance and servicing mechanically and electrically, including draining out existing transformer oil and cleaning, oiling /greasing, removing & replacement of defective / unserviceable parts with new parts, as required at site and manufacturer's instructions and checking electronic circuits to make it functional, reassembling the parts of voltage stabilizer after overhauling / servicing at position ensuring proper output connecting to existing system and applying one coat of synthetic enamelled paint (heat resistant type) by spray machine after preparation including writing MES No/ SM No in capital letters of suitable size on body of stabilizer and making voltage stabilizer perfectly operational and testing at site on existing connected load to the entire satisfaction of the Engineer-in-Charge, complete all as specified and directed. Notes :- (i) Replacement of unserviceable parts shall be measured and paid for separately under appropriate item of Sch ‘A’ as supply only but fix charges of the parts replaced/ repaired is deemed to be included in this item. (ii) Oil shall be drained out and collected in contractors own containers and reuse after heating and filtration through filtration plant to achieve the suitable dielectric strength/insulation value. Refilling, heating and filtration shall be included in the rate quoted by the contractor for this item. (iii) Fresh oil required for top up shall be measured as “supply only” but its heating and filling shall be included in the rate quoted by the contractor for this item. (iv) The quoted rate shall be deemed to include replacement of small/ minor parts i.e. washers, nut bolts, packing, screws, lamp etc.

Supply only servo motor 10 Kg-cm capacity.

Supply only complete control wiring for each phase.

Supply only RC Net Work 10 Kg-cm (Resistor- Capacitor network)

Supply only Volt meter 0-440 volts, as existing type

Supply only VARIAC Coil 250 KVA capacity per Phase

M/S Chib Engineers (BID ID -3392759)