PROVISION OF AREA DRAINAGE AT CDO TRG AREA OF HQ JL WING AND AT CERTAIN OTHER PLACES AND REPLACEMENT OF OLD SEWAGE LINES OF HOSPITAL AREA OF MH BELGAUM UNDER GE BELGAUM

Amount

Surface excavation n.exc. 30cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and as directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in hard/ dense soil all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in sorf disintegrated rock all as specified and directed.

Excavation in trenches n. exc. 1.5 m wide and n. exc. 1.5 m depth for foundation, etc. and getting out in Hard rock by chiselling all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layers n. exc. 25 cm thick all as specified and directed.

Removing excavated soil n.exc 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soil all as specified and directed.

M&L for plain cement concrete type D2 1:4:8 using 40mm graded stone aggregate as in foundation and mass concrete all as specified and directed.

M&L for pre-cast cement concrete solid block masonry, exc 10 cm width, blocks cast in PCC 1:3:6, type C0, using 12.5mm graded stone aggregate and setting in CM 1:6 all as specified and directed.

M&L plain cement concrete 1:3:6, type C1, using 20mm graded stone aggregate as in coping, bed plates and similar works including necessary form work all as specified and directed

M&L for plain cement concrete 1;2:4 type B1, using 20mm graded stone aggregate in surface channels, drains, coping and similar works including necessary form wok all as specified and directed.

M&L for extra for forming fair finished drain or channel of 25cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for extra for forming fair finished drain or channel of 30cm inner girth in cement concrete using extra cement including forms moulds mitred / stopped end etc. all as specified and directed.

M&L for pre-cast cement concrete manholes cover, blocks cast in PCC 1:2:4, type B1, using 20 mm graded stone aggregate and jointed in CM 1:6 all as specified and directed.

M&L for Reinforced cement concrete 1:2:4, Type B1 using 20mm graded stone aggregate as in slabs supported on walls, beams and columns complete all as specified and directed.

M&L for use of Formwork to soffits of suspended slabs not exceeding 200mm thick for rough finished flat concrete surfaces, horizontal or sloping all as specified and directed

S&F mild steel framed work such as grills, gratings etc., with ends of bars shouldered and/ or riveted or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290 Gde- E-165 all as specified and as directed.

M&L for mild steel TMT bars 8mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

All as described in item No. 17 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders.

M&L for mild steel round bars 10mm dia and over cut to length bent to shape required including cranking bending, spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia all as specified and directed.

M&L for 40mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate as in flooring in drains all as specified and directed.

M&L for 100mm thick plain cement concrete 1:2:4 type B1 using 20mm graded aggregate, as in flooring, finished even and smooth without using extra cement all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or block masonry or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick in cement mortar 1: 4 mixed with water proofing compound on fair faces of brick work or PCC block masonry or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Supply only approved integral water proofing compound all as specified and as directed.

M&L for 150mm bore Reinforced cement concrete pipes, class NP2, laid and jointed with collars including demolition and breaking up existing bed concrete and SGSW/ RCC drain pipes and taking out of trenches all as specified and as directed.

M&L for 200mm bore Reinforced cement concrete pipes, class NP2, llaid and jointed with collars including demolition and breaking up existing bed concrete and SGSW/ RCC drain pipes and taking out of trenches all as specified and as directed.

M&L for 300mm bore Reinforced cement concrete pipes, class NP2, laid and jointed complete with collars all as specified and as directed.

M&L for bed concrete to 150mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

M&L for bed concrete to 200mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

M&L for bed concrete to 300mm bore drain pipes in Plain Cement Concrete 1:4:8 type D2 using 40 mm graded stone aggregate including packing under and haunching against the sides of pipe after they are laid and tested all as specified and directed.

Cutting into existing manholes for connecting new drain pipe of 150mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

Cutting into existing manholes for connecting new drain pipe of 200mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

Demolition of existing dilapidated RCC man hole cover slab of any discription and size all as specified and directed.

Demolition of brick work or stone masonry built in cement mortar or lime cement mortar including all quoins, arches, pillars, etc. but excluding ashlar facings, dressed stonework and precast concrete articles, in any position below or above ground level all as specified and directed.

M/S VISHWAROOP ELECTRONICS AND ELECTRICALS

M/s. KIRAN M CHOUGULE

ASHIRWAD ELECTRICALS

Vinod Enterprises

RAJENDRA KRISHNA SARAF