Construction of Central Control Building for Housing Emergency Operation Centre and SCADA System (Supervisory Control And Data Acquisition) and other Allied Works.

Amount

Earthwork

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: (code no 2.9.1) All kinds of soil :

Soling

Providing and laying of hand packed stone soling (size 150mm-230mm) before laying of mud mat including ramming and compacting with hand rammers including all carriages.

Mudmat

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing and all carriages but excluding the cost of centring, shuttering and finishing with. (code no,4.4.7 )

Mass Concrete

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shuttering and finishing with. 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)(code no 4.4.3)

Filling

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete including all carriages.(Codeno 2.23)

Backfilling available excavated earth excluding rock including all lifdts and leads complete job including consolidation compaction in 20cm layers watering all complete job(Code no 2.11)

Supplying,filling with boulders handpacked complete carriage upto site of work all complete.

Supplying and filling of local earth (including royalty)by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete including all carriages complete. (code no :2.11)

Providing and laying in position specified grade of reinforced cement concrete including curing including all carriages complete. but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)(SSR 2020)5.1.2

Providing and laying in position cement concrete of specified grade including curing including all carriages complete. but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)(SSR 2020)4.4.5

Controlled Cement Concrete (M25)

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improveworkability without impairing strength and durability as per direction of Engineer-in-charge. Note: - Cement in this item is @ 330 kg/ cum. Excess or less cement used as per design mix is content considered payable or recoverable separately. ..1 All works upto plinth level including all carriages(Code no 5.38)

All works above plinth level upto floor V level (Code no 5.38.2 )

Formwork

Centering and shuttering including strutting, propping etc. and removal of form for: codeno 5.9

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc

Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Columns, pillars, piers, abutments, posts and struts.

Stairs (excluding landings) except spiral staircases.

Suspended floors, roofs, landings, balconies and access platforms.

Reinforcing Steel

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more(codeno. 5.22A.6 ).

Structural steel

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (code no 10.2.2 )

Providing and fixing bolts including nuts and washers complete.(codeno 10.22)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete(SSR 2020)4.17

Brick Works

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing including all carriages. Cement mortar 1:6 ( 1 cement : 6 coarse sand)(:(SSR 2020) 6.1.5

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level (SSR 2020) 6.4

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)(SSR 2020) 6.15.2

Extra for half Brick masonry in superstructure above plinth level upto floor V level (SSR 2020) 6.16

Extra for providing and placing in position 2 Nos. 6mm dia. M.S. bars at every third course of half brick masonry.(SSR 2020) 6.18

Plastering Works

15mm cement plaster on the rough side of single or half brick wall of mix 1:6 (1 cement: 6 fine sand) (including cost of all material, leads, lifts and carriages etc upto site of work complete).(inner side) (SSR 2020) 6.16

18mm Cement plaster in two coats under layer 12mm thick cement plaster 1 : 5 (1 cement : 5 coarse sand) finished with a top layer 6mm thick cement plaster 1 : 6 (1 cement : 6 fine sand) design as per architectural drawing. including all carriages ( outer side in groves)SSR 2020) 13.12

12 mm thick cement plaster on ceilings, etc. in (1 cement: 4 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).SSR 2020) 13.1.1

UPVC Window

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shallbe also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacentfinished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing& direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately)Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation inprofile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement window double panels with S.S. friction hinges (300x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension.(ssr 2020 9.149.A2)

Providing and fixing glazing in upvc door, window, ventilator, shutters and partitions etc. complete as per the architectural drawings and the directions of engineerin-charge. With toughen glass transparent in colour of 5.0 mm thickness.

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 10 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(SSR 2020) 9.14.C.2

Providing and fixing 8mm thick high pressure laminated sheets matt finish in upvc doors and partation walls etc complete as per the architectural drawing and the directions of engineer in charge

Filling the gap in between aluminum frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5mm width. (SSR 2020) 22.8.1

PARTITION WALLS(U-PVC)

Providing and fixing factory made uPVC white colour partation walls comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. sealant shall be paid separately) Note: dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Dimensions of sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Specification same as per shedule2020 item no 9.14.C.2/9.149 A2)

Providing and fixing 12 mm thick frameless toughened glass of approved brand and manufacture, including providing and fixing top , bottom & sides with fiiting arrangement and making necessary holes etc. for fixing required all complete as per direction of Engineer-in-charge ( for waiting)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot &double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).(SSR 2020) 22.18

Door handle(stainless steel pipe pull handle bocare(25x127x457 mm) item weight 770 grams

door lockstainless steel(90x140x100 mm)glass to glass lock shape ovel

Door stopper(door mount ,stainless steel)

WOOD WORK:-

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): First class deodar wood.(SSR 2020)9.1.3

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws 35mm thick (SSR 2020) 9.21.1

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a coat of approved primer on one face, and fixed on wooden /steel frame work, complete as per direction of Engineer-in-charge (Frame work shall be paid for separately). 12mm thick commercial ply conforming to S : 1328 BWR type (SSR 2020) 9.142.1

Providing and fixing 4mm thick coir veneer board ISI marked IS:14842 plain lining with necessary screws, priming coat on unexposed surface etc. complete (SSR 2020) 8.29

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured) (SSR 2020) 9.24

FIXTURES FOR DOORS

Providing and fixing hardware fittings of approved brand and of required type as approved by Engineer incharge. complete as per the specifications . (Brass)

Modular door lock ss finish handle 10" with duaal locking system inside & outside

Tower bolts 150mm (doors)(SSR 2020) 402

Handle 150mm (door)(SSR 2020) 409

Flooring /walls:-

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent (SSR 2020) 11.66

Providing and fixing 16 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour or shade .(SSR 2020)8.2.2.1

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of tile 600x600 mm(double charge(SSR 2020)11.54.2

Providing and fixing 1st quality ceramic glazed floor tiles conforming toIS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.(SSR2020)11.50A

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.(SSR 2020)8.31

Providing and fixing of 75 mm thick dewri stones tiles in flooring with single face fine cheasled only over a bed of cement concrete of grade 1:2:4 of thickness upto 75mm including all carriages complete job.(ramp external)

Kota stone slab flooring 25 mm thick over 20mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing, polishing and curing complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) :(SSR 2020)11.36

Providing and fixing carpet sheet/roll 4.3mm thick cut pile floor covering, pile material 100% nylon 6.6 having resilient water proof backing material and total weight of carpet should be 1.8 Kg/sqm and anti sound absortion of 0.10 of Consolidated Carpet make or approved equivalent make and shade in flooring and skirting in approved pattern on a smooth top and damp proof base using adhesive of approved quality and manufacture including rolling with light wooden roller and the cost of levelling the surface with self levelling adhessive etc. all complete as per manufacturer's specification.

Wooden planking, tongued and grooved in flooring including fixing with iron screws complete: 25 mm thick Second class teak wood,(SSR 2020)11.43.4.1

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(angle 50x 50 x5 mm) for media centre plate form(SSR 2020)10.1

Providing and fixing removable raised/false access flooring with system and its components of approved make for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the architectural drawings, as specified and as directed by Engineer-in-charge consisting of: (a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor (base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug. (b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge. (c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges: top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along each flange). The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom plate is filled with Pyro grip non-combustible Portland cementitious core mixed with lightweight foaming compound. The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto 1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the product. 300 mm Finished Floor Height (FFH)(SSR 2020)11.67.1

Painting / finishing Works :-

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.(SSR2020)13.88.2

Painting with acrylic emulsion paint of approved brand and manufacture to give an even shade. Two or more coats on new work(SSR 2020)13.69

With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)(SSR2020)13.58.1

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.(SSR2020)13.70.1

Proving and fixing of washable wall paper for wall Including cost of necessary adhesive specification and design approved by engineer incharge/consultants/client.complete job

Water Proofing :-

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with Armourcrete of M/s The Structural Water Proofing Company Pvt. Ltd. Or Tapecrete of M/s CICO Technologies Ltd. consisting of applying : First layer of slurry of cement @ 0.488 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.253 kg/Sqm. This layer will be allowed to air cure for 4 hours. Second layer of slurry of cement @ 0.242 kg/Sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes supply of waterproofing compound, preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry).(SSR 2020)23.5

Fire Rated Doors

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³. The frame will have a provision of G.I. Anchor fastners 14 nos (5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge. (Cost of SS ball bearing hinges is excluded).(SSR 2020)9.158

Providing and fixing 60 mm thick glazed fire resistant door shutters of120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for separately).(SSR 2020)9.159

Providing and fixing glazing in fire resistant door shutters, fixed panels& partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturers have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.(SSR 2020)9.161

Providing and fixing of DORMA Make or equivalent SS Ball Bearing Hinges of 100 x 89 x 3mm SUS 304 Grade complete with SS Screws ( 4 Nos per panel )

Providing and fixing of DORMA TS 73V door closers tested in accordance with BS: 476 Part – 22: 1987 with manufacturers warranty and tested with complete assembly offerred by manufacturer

Providing and fixing of DORMA make Lock 952 F alongwith 80mm Cylinder and necessary screws as required.

Providing and fixing of Dorma make Tower Bolt 600 mm long

RAILING

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer.(SSR2020)10.26

Providing and fixing 75 x 60 mm moulded/ornamental hand rails in straight lenghts/curved in shape where required and approved by consultant completes for stair cases / verandas etc. Including al necessary fittings/fixtures (ist class deodar wood) as per direction engineer incharge

Providing and fixing moulded / ornamental newel post wrough fixed with ends houses(square or splay) to hand rails ans treads or strings completes (100mm nominal dia ans 1000 mm long) with turned caps fixed on top as per directions including all necessary fittings/ fixtures(ist class dewdar wood) as per direction of consultants/ as per the drawing enclosed.

French spirit polishing, Two or more coats on new works including a coat of wood filler.(SSR 2020)13.78

Melamine polishing on wood work (one or more coats)(SSR 2020)13.122

Polishing on wood work with ready mixed wax polish of approved brand and manufacture on New work(SSR 2020)13.77

Ceiling Works :-

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-incharge With 20 mm thick beveled tegular mineral fibre false ceiling tile (NRC 0.7) (DSR2018) 26.27.2

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm diax40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of required size and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26 mm each having clips of 10.5 mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm diaX230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimetre channel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the gypsum board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers’ specification and also including the cost of making openings for light fittings, grills diffusers, cutouts made with frame of perimetre channels suitably fixed all complete as per drawing and specification and direction of the Engineer-in-Charge but excluding the cost of painting with: 8 mm thick Calcium Silicate Board made with Calcareous and Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.(SSR 2020) 12.62.5

Providing & applying Plaster of Paris (gypsum anhydrous) suspended false ceiling Cove false ceiling), vertical or horizontal with wooden pattern in between with a ratio of ( 70% Gypsun ceiling -30% wooden ) up to any height above floor level, including fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive). Consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts. Other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size. The other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre. This shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval and reinforced with rabbit wire mesh of 100mmx16mm gauge fixed to frame.

Providing/fixing of Khatambandi Ceiling of ist Class Budloo Wood of specified pattern in ceilings etc. including, necessary frame work work of 50 mmx 75mm size ,and 12mm thick ply board frame in lining of Budloo wood underneath and other incidentals including cornice of size 75mmx75mm/2 of Budloo Wood all complete in all respectes.as per the directions of Consultant/as per the drawings enclosed.(SSR 2020)12.71.6

Acoustical Wall Paneling

Providing and supplying Acoustical Wall Paneling’ with square edges made of fibre glass substrate 25mm thick and wrapped on the front side with an acoustically transparent and classified for Fire reaction Class B-s1, d1 as per EN13501, fabric with an option of colors – Ivory, Autumn Orange, Pista Green, Straw Gold, Rustic Green, Burgundy, Rust, Peacock Blue, Ash Grey, Mocha as per the choice of the Architect of size 600X1200 mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using Wall panel impalers supplied by Manufracturer and construction adhesives as per the instructions laid down by the manufacturer. INSTALLATION:4nos. wall panel Impalers of shall be fixed to the wall surface using self tapping screws. Silica based construction adhesive to be dabbed on to the projecting elements (spikes) of the impalers. wall panels shall be pierced through the spikes of the impalers ensuring the line and level of the panels are maintained.

Providing and fixing plannes eaves boarding (300mm x 40mm )( nominal size) second class dewdare wood fixed with screws etc, including all carraiges .All job completed.(SSR2020)12.69.1.2

Providing and fixing 20mm thick wooden planks ceiling (frame work for base to be paid for separately) with M.S. screws 2nd class kail wood.(SSR2020)12.34

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position : Budloo wood(SSR2020)9.4.6

Providing and laying roof insulation with 40 mm thick impervious sprayed, closed cell free Rigid Polyurethane foam over deck insulation conforming to IS - 12432 Pt. III (density of foam being 40-45 kg/cum), over a coat of polyurethane primer applied @ 6-8 sqm per liter, laying 400 G polythene sheet over PUF spray and providing a wearing course of 40 mm thick cement screed 1: 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic, all complete as per direction of Engineer-inCharge.(SSR2020)12.68

Providing colour coated corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 1.25 mm thick with zinc coating not less than 350 gram/m2(SSR 2020)12.1.2

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275 gram/m (SSR 2020)12.4.1

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.1.60 mm thick with zinc coating not less than 350 gram/m2(SSR2020)12.5.1

External Finish

Finishing walls with exterior ultima Allura Torino paint of required shade texture rough washability, anti fungal, @ 0.4 kgs / sqm in two coats Including primer coat complete in all respects

12 mm Cement plaster on sides of windows doors ventilators etc. in (1 cement: 2 fine sand mix). Upto floor V level complete in all respects (including cost of all material, leads, lifts and carriages etc. upto site of work complete).(SSR2020)13.1.1

Providing and fixing devri stone clading 25 mm thick with exposed face fine dressed with rough backing on wall lining etc. upto 10 meter ht back filled with a grout of 12 mm thick cement sand mortar in 1:3 (fine cheiseled)including pointing in white cement 1:2 with admixture of pigment matching to stone.

Fabrication of modular kitchen with space of electronic chummney all type of modular steel baskets and accessories with provision of plate stand racks spoon basket try , cutlery basket, cup and saucer basket partation basket grain trolly withwith slider tray chennel and finish with granite top . Cbnite fabricate with 25 mm commercial board with over lap modular doors with hydralic auto closed hinges with fixing 8 degree or 0 degree and fixing of key lock and sliding drawers with railing channel size 450 mm in both side of each drawer , drawer lock and steel handle size 100mm inside the cabnit will be laminated sheet 0.8mm thick and outside laminated with texture design 1 mm thick laminate the cabnit will be divide in partation with 25 mm thick wooden board and both sides uper file cabnit, storage cabnit, and lower side cabnit with all locking arragment as per drawing. complete job

Providing and fabrication of wooden modular wadrobe with wall to wall and top to bottom finish with locking mirror and drawers as per drawing total size 1500mm wide x 3000 mm height x600 mm deep with 25 mm thick commercial board with over lap modular doors with hydrolic auto closed hinges with fixing 8 degree or 0 degree and fixed of key lock and sliding drawers with size 600mm x 150mm x 600mm with railing channel size 450mm in both sides for each drawer, drawer locks and steel handle size 100mm inside the cabnit will be laminated with plane laminated sheet 0.8mm thick with and out side laminated with texture design 1 mm thick laminate the cabnit will be divide into partation 25mm wooden board and both sides upper file cabnit, storage,and lower side cabnit with all locking arragment as per drawing complete job

Proving and fixing of second class deodar wood for wall penelling designed in ornamental pannals shape square / rectangular.(the ornamental panals made up of 12 mm thick of dewdare wood and frame made up of 25 mm thick where 12 mm ornamental panals are fixed Including cost of necessary adhesive ,budloo wood backing and cost of nails etc design approved by Architect/engineer in charge/consultants.complete job.

SIGNAGES :

Manufacturing supplying and fixing retro reflective overhead signage boards made up of 2mm thick aluminum sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type-III of ASTM-D-4956-01 as approved by Engineer-in-charge; letters, borders etc. as per IRC : 67-2001 in silver white with blue colour background and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class -II of ASTM-D-4956- 01 and fixing the same to the plate of structural frame work by means of suitable sized aluminum alloys, rivets or bolts and nuts @ 300mm c/c all along the periphery as well as in two vertical rows along with theft resistant measures including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminum sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the structural frame work from the gantry, fixing and erecting the same in position all complete as per drawing, specification and direction of Engineer-in-charge (Structural frame work including M.S. plate to be provided separately. Rectangular area of the sheet only shall be measured for payment)(SSR 2020)16.67

Supply and installation signage plates for rooms.meeting halls etc of size 120mm x120mm x1.5mm in ss304 matt finish having letters engrave in the ss plate in black vinyl steam pressed to get a clean finish and having font size of name atleast 30mm fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to thesatisfaction of engineer in charge

Supply and installation signage plates for FIRE EXIT/ LIFT SIGNAGE of size 120mm x120mm x1.5mm in ss304 matt finish having letters engrave in the ss plate in black vinyl steam pressed to get a clean finish and having font size of name atleast 40mm fixed on the wall or door surface with high quality adhesive tape of 3M or equivalent complete to thesatisfaction of engineer in charge.

External work :-

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry bricks 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth.(SSR2020)4.24

Suppying and fixing rolling shutters of approved make,made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 em long wire springs manufacture from high tensile steel wire of adequate strength confirming to IS 4454 part1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover.(SSR 2020)10.6.1

Providing and fixing ball bearing for rolling shutters.(SSR 2020)10.7

Extra for providing mechanical device chain crank operation for operating rolling shutter(SSR 2020)10.8

Chequerred terrazo tiles 22mm thick with graded marble chips of size upto 6mm in floors jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand) Light shade using white cement.(SSR 2020)11.28.1

62mm thick cement concrete flooring with concrete hardener topping under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 liter per 50kg of cement or as per manufacturer’s specifications, and 30 kg iron slag/cum including cost of cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete.(SSR2020)11.7

Providing and fixing strips in joints of terrazzo/ cement concrete floors glass strip 40 mm wide and 4 mm thick(SSR2020)11.16.1.1

Stone work in super structure upto floor five level in cement mortar 1:6 ( 1 cement :6 coarse sand) including pointing with cement mortar 1:2 ( 1 white cement: 2 stone dust) with an admixture of pigment matching the stone shade and curing complete: both face dressed red sand stone.(ASHLAR MaSONARY)(SSR2020)7.10.1.2

Stone work, in copings, cornices, string courses and plinth courses, upto 75mm thick, in cement mortar 1:6 (1 cement : 6 Coarse sand) including pointing with white cement mortar 1:2 (1 cement : 2 Stone dust) with an admixture of pigment matching the stone shade& curing complete.(ASHLAR MASONARY)(SSR2020)7.29.1

Providing and fixing G. I. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as requiredMade of G. I. wire of dia 4mm, PVC coated to achieve outer dia, not less than 5mm in required colour and shade. complete as per direction of Engineer-in-charge. (SSR 2020)16.25.2

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(angle 50x 50 x5 mm)(SSR2020)10.1

Tile brick masonry work 5cm thick with common burnt clay non modular tile bricks of class designation 10 in cement mortar 1:3 (1 cement : 3 coarse sand) and curing complete in superstructure above plinth level upto floor five level.(SSR2020)6.28

Preparation of subgrade by excavating earth to an average of 22.5 em depth, dressing to camber and consolidation with road roller including making good the undulation etc. and disposal of surplus earth upto 50 metres.(SSR 2020)16.2

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge.1 With material conforming to Grade-I (size range 75 mm to 0.075 mm) (SSR 2020)16.82.1

Supplying and stacking at site.Graded crushed stone aggregate of size

63 mm to 45 mm(SSR 2020)16.4.1.2

53 mm to 22.4 mm(SSR 2020)16.4.1.3

Stone screening of size 11.2 mm nominal size (Type B)(SSR 2020)16.4.3.2

Laying, spreading and compacting stone aggregate of specified sizes to WBM specifications in uniform thickness, hand picking, rolling with 3 wheeled road / vibratory roller 8-10 tonne capacity in stages to proper grade and camber, applying and brooming requisite type of screening /binding material to fill up interstices of coarse aggregate, watering and compacting to the required density.(SSR 2020)16.5

providing and laying of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15.1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-incharge. (SSR2020)16.84

Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarse sand and graded stone aggregate of 40 mm nominal size in appropriate proportions as per approved & specified design criteria, providing dowel bars with sleeve/ tie bars, 150 micron polythene wherever required, laying at site, spreading and compacting mechanically by using needle and surface vibrators, leveling to required slope/ camber, finishing with required texture, including steel form work with sturdy M.S. channel sections, curing, making provision for contraction/ expansion, construction & longitudinal joints ( 10 mm wide x 50 mm deep) by groove cutting machine, providing and filling joints with approved joint filler and sealants, complete all as per direction of Engineer-in- charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars to ,be paid separately). Note:-Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. Cement concrete prepared with batch mixing machine(SSR 2020)16.51.1

Providing and laying in 20 mm thick dowel bars at joint 500mm centre to centre(SSR2020)1004

Providing and fixing pvc pipes in 32mm OD thick for dowel bars at joint 500 mm centre to centre(SSR2020)19.3.1.4

Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade ‘A’ sealing compound.(SSR2020)16.54.1

Painting runway / taxi track/ apron marking with adequate no. of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge including cleaning the surface of all dirt, scales, oil, grease and other foreign material etc. and lining out complete.New work (Two or more coats)New work (Two or more coats)(SSR2020)16.55.1

Providing and laying chisel dressed Devri Stone of size 300x200 mm face with 150 mm depth in cement mortar 1: 6 (1 cement : 6 coarse sand) upto floor level including curing. One face dressed. Fine chisel dressed(SSR 2020)7.44.1

Extra for fine chisel dressed Devri Stone in square or rectangular Pillars(SSR2020)7.45

Providing and fixing hold fast made of structural steel including cost carriage primer coat complete job

Providing and fixing roller supports for gates including cost carriage primer coat etc complete job

Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. On W.B.M. @ 0.75 Kg/sqm.(SSR2020)16.38.1

Providing and applying tack coat using hot straight run bitumen of grade – VG-10, including heating the bitumen, spraying the bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per specifications. On bitumen surface @ 0.50 Kg/sqm.(SSR2020)16.38.2

Providing and laying bituminous macadam using crushed stone aggregates of specified grading premixed with bituminous binder, transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density, complete as per specifications and directions of Engineer-in-Charge. 50 mm average compacted thickness with bitumen of grade VG-30 @ 3.5% (percentage by weight of total mix) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity. (SSR2020)16.63.1

Providing and laying semi- dense Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as per specification, complete and as per directions of Engineer-in-Charge. Plant of 100-120 TPH capacity. (SSR2020)16.64.1

Providing and laying seal coat of premixed fine aggregate (passing 2.36 mm and retained on 180 micron sieve) with bitumen using 128 kg of bitumen of grade VG-10 bitumen per cum of fine aggregate and 0.60 cum of fine aggregate per 100 sqm of road surface including rolling and finishing with road all complete(SSR2020)16.48

Filling in paths etc in layers not exceeding 20 cm in depth consolidating each layer by rammng, watering complete job

a) GSB filling under in paths.(SSR 2020)16.8.2+ CARRIAGE)

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement: 3 coarse sand) including making joints with or without grooves (thickness of the joints except at sharp curve shall not to be more than 5mm) including making drainage opening wherever required complete etc. as per direction of Engineer-incharge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).(SSR 2020)16.75

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, filling the joints with coarse sand etc. all complete as per direction of Engineer-in-charge.(SSR 2020)16.74

Providing Retro-reflective regulatory sign board of size 900mm diameter made out of 2mm thick aluminum sheet, face to be fully covered with high intensity encapsulated lens type retro-reflective sheeting as approved by Engineer-in-charge. Letter, symbols, borders, etc. will be as per IRC:67 with required colour scheme on the boards and with the high intensity grade A. the aluminum sheet to be riveted to M.S. frame of angle iron of size 40x40x4mm. The boards will be fixed to 1 No. 50x50mm square post made of M.S. angle 50x50x4mm, 4m long welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminum sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per directions of Engineer-in-charge.(SSR 2020)16.68

Supplying and stacking of good earth at site including royalty (earth measured in stacks will be reduced by 20% for payment)(SSR 2020)17.3

Spreading of sludge, dump manure or/and good earth in required thickness as per directions of officer in-charge (cost of sludge, dump manure or/and good earth to be paid separately)(SSR2020)17.8

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.(SSR2020)2.7.1

GABION WALL

Providing and making Gabion structure with mechanically woven double twisted hexagonal shaped wire mesh Gabion boxes as per IS 16014:2012, MORTH clause 2500, of required size, Mesh type 10x12 (D=100mm with tolerance of ± 2%), zinic +10% ,Al alloy + PVC coated, mesh wire diameter 2.7/3.7 mm ( ID/OD), mechanically edged/selvedged with partitions at every 1 m interval and shall have minimum 10Nos. of openings per meter of mesh perpendicular to twist, tying with lacing wire of diameter 2.2/3.2mm (ID/OD), supplied @3% by weight Gabion boxes filled with boulders with least dimension of 200mm, as per drawing, all complete as per directions of engineer-in-charge. (16.100)

SERVICES

SUB HEAD (I) ELECTRICAL

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in Existing surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. DSR 2018 1.10.3

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.DSR 2018 1.55.3

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.DSR 20181.21

20mmDSR 20181.21.1

25mmDSR 20181.21.2

32mmDSR 20181.21.3

40mmDSR 20181.21.4

Wiring for Light /Power Plug with 2 x 4 sq.mm FRLS PVC Insulated Copper Conductor single core cable in Existing surface/Recessed medium class PVC Conduit along with 1 No. 4 sq.mm FRLS PVC Insulated copper conductor single core cable for loop earthing as required.DSR 20181.12

Wiring for Circuit/Submain Wiring along with earth Wire with the following Sizes of FRLSPVC insulated copper conductor,single core Cable in Existing surface/Recessed medium class PVC conduit as required.DSR 20181.14

2 X 2.5 SQ.MM + 1 X 2.5 SQ.MM EARTH WIREDSR 20181.14.2

4 X 4 sq. mm + 2 X 4 sq. mm earth wireDSR 20181.14.8

4 X 6 sq. mm + 2 X 6 sq. mm earth wireDSR 20181.14.9

4 X 16 sq. mm + 2 X 6 sq. mm earth wireDSR 20181.14.11

4 X 25 sq. mm + 2 X 16 sq. mm earth wireN.S

4 X 50 sq. mm + 2 X 25 sq. mm earth wireN.S

Supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate as requiredDSR 20181.26

Supplying and fixing Stepped Type Electronic Fan Regulator on the existing Modular Plate Switch Box including Connections but Excluding Modular Plate etc. as RequiredDSR 20181.25

Supplying and Fixing suitable size G.I box with modular plate and cover in front on surface or in recess,including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch,connection,painting etc. as required.DSR 20181.32

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.DSR 20181.31

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as requiredDSR 20181.57

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)DSR 20182.4

4 way (4 + 12), Double doorDSR 20182.4.1

6 way (4 + 18), Double doorDSR 20182.4.2

12 way (4 + 36), Double doorN.S

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.DSR 20182.13

40 AmpsDSR 20182.13.1

63 AmpsDSR 20182.13.2

25 AmpsN.S

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)DSR 20182.3

12 way , Double doorDSR 20182.3.3

6 way , Double doorDSR 20182.3.1

Supplying and fixing following way VTPN D.B Conforming to IS:8623-1 and 3,IEC 61439-1 and 3 ,IK-08 Compliant,IP43 fabricated out of CRCA sheet SteelN.S

12 Way Incomer MCCB and Out going 12+12+12

Supplying and fixing 5 amps. to 32 amps.rating 240 volts 'C' series, miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.DSR 20182.1

Single PoleDSR 20182.10.1

Double PoleDSR 20182.10.3

Triple pole and neutralDSR 20182.10.5

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required.DSR 20182.2

100 A,36KA,FPMCCBDSR 20182.2.13

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.DSR 20182.11

ENVIRONMENTALLY SAFE MAINTENANCE FREE EARTHING SYSTEM

Necessary soil treatment is to be made by the contractor in order to improve the Pit resistance value. N.S

Supply, installation, testing and commissioning of Advanced Maintenance Free environment friendly Earthing system consisting of 1 no. of 3mtr length, 17.2 mm dia UL certified earth electrode made of high tensile low carbon steel circular rods, molecularly bonded copper on outer surface (minimum copper bonding thickness-250 microns) with GI terminals to connect incoming strips, (Environment friendly backfill compound duly certified as per ANSI/NSF standard 60/Toxic content certificate as safe for use near potable ground water resources strictly as per specification enclosed.

Earth pit chamber (300mm x 300mm) with CI cover for the above.

Providing and Fixing 25 mm x 5 mm Copper Strip in 40 mm dia. G.I Pipe FRL Earth Electrode including connection with Brass nut ,bolt,spring,washer,excavation and refilling etc. as required.DSR 20185.1

SITC of Ceiling Fan,Capacitor type suitable for low voltage operation including wiring the down rods of standard length(Upto 30 cm)with 1.5 sq.mm FR PVC insulated,copper conductor,single core cable including providing and fixing phenolic laminated sheet cover on the Fan Box etc as Required.N.S

1200 MM SWEEP(5 STAR)

SITC of pre-wired Recess/Surface Mounted 2Ft X 2 Ft LED Panel Fitting with ,Driver Etc. including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required. (.JAQUAR /WIPRO/PHILIPS or equivalent)125 LUMEN/WATTN.S

SITC of pre-wired Recess /Surface Mounted LED Ceiling Light 12 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required.(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

SITC of pre-wired Recess /Surface Mounted LED Ceiling Light High Bay 150 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

SITC of pre-wired Recess Mounted LED Ceiling Light 18 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

SITC of pre-wired Surface Mounted LED Ceiling Light 18 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required.(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

SITC of pre-wired Surface Mounted LED Tubelight Light 1 x 22 W including connections with 1.5 sq.mm FR PVC insulated copper conductor single core cable and earthing etc as required(.JAQUAR /WIPRO/PHILIPS or equivalent)N.S

Supply of AC 230/250 Volts, 50 Hz exhaust fan with louveres of Following Sizes including connection etc. complete as required .N.S

5 KVA with Single Phase input and Single Phase Output

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.DSR 20182.2

1 KVA with Single Phase input and Single Phase Output

5 KVA with Single Phase input and Single Phase Output

10 KVA with Single Phase input and Single Phase Output

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.DSR 201814.16

200 mm dia (OD-200 mm & ID-175 mm nominal)DSR 201814.16.5

Supplying and Laying of 1 No XLPE insulated and PVC Sheathed /XLPE Power Cable of 1.1 KV Grade of Following Sizes in the existing RCC/Hume/DWC/Stone ware/Metal Pipe/Cable Tray as Required.N.S

3.5 C x 300 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

3.5C x 185 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

3.5 C x 50mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

3.5 C x 25mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

4.0 C x 16mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.N.S

Supply, Installation testing and commissioning of 3 C x 120mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)N.S

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.DSR 20189.1

3.5 C x 300 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 20189.1.30

3.5C x 185 mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 20189.1.27

3.5 C x 50mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 20189.1.22

3.5 C x 25mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.DSR 20189.1.20

4.0 C x 16mm² LT XLPE (A2XFY) insulated Aluminium conductor PVC outer sheathed Armoured cable.9.1.33

Supply, Installation testing and commissioning of Outdoor/Indoor Termintion Kit for 3 C x 120mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)N.S

20KVA/20KW TRUE ONLINE UPS : 20KVA/20KW True Online Modular UPS with 20 KW Power Cabinet with 3 no. of 6.7KW power Modules with 240VDC along with external SMF Battery Bank of minimum VAH of 18000 with 2 year onsite Warranty. Battery Make: - Exide Power Safe/ Quanta Make Batteries, With MS battery rack, BCB, Links & 1 x DC cable 5mtrs. N.S

30KVA/30KW True Online Modular UPS with 30 KW Power Cabinet with 6 no. of 5 KW power Modules with 240VDC along with external SMF Battery Bank of minimum VAH of 28800VAH with 2 year onsite Warranty. Battery Make: - Exide Power Safe/ Quanta Make Batteries, With MS battery rack, BCB, Links & 1 x DC cable 5mtrs. N.S

Supply,Installation of POP UP Boxes of Following SizesN.S

8 Modulea

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.

300 mm width X 50 mm depth X 1.6 mm thicknessDSR 20184.6.4

450 mm width X 50 mm depth X 2.0 mm thicknessDSR 20184.6.6

600 mm width X 50 mm depth X 2.0 mm thicknessDSR 20184.6.7

Supply, transport, unloading, shifting & Fabrication of steel sections and erection of MS base frames, MS angle channels, flat etc for supporting various items of equipment such as various panels/switchgear,dummey panels, adaptor boxes addition support for proper cable termination, MS Fabricated cable trays, push button stations, junction boxes, light fittings, DB etc. The scope include welding, bolting, chipping , grouting etc, including applying one antirust coat of approved primer and two finished coats of approved paint with primer & paint, breaking and finishing of walls, floors etc. Contractor has to apply one coat of antirust paint (Red-oxcide ) with in one day after structural steel received. The scope is inclusive of minor civil work as required, supply of GI hardware materials, consumables, tools & tackles and necessary labour with supervision but not limited to, and complete as per approved drawings, specification and directions of Engineer-In charge.N.S

SUB HEAD (II) FIRE DETECTION

Two Loop Panel.DSR 201817.2.1.2

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.DSR 201817.2.3

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.DSR 201817.2.4

Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete asrequired. DSR 201817.2.6

Supplying, installation, testing & commissioning of fault isolator complete with base as required.DSR 201817.2.7

Supplying, installation, testing & commissioning of addressable manual call point complete as required.DSR 201817.2.14

Supply and drawing of 2 C X 1.5 Sq mm Un armoured cable in Existing Conduit.N.S

Supplying and Fixing of Following sizes of PVC Conduit along with Accessories in surface/Recess including painting in case of surface conduit,cutting the wall and making good the same in case of recessed conduit as required.

25mm PVC ConduitDSR 20181.21.2

SITC of ABC Type Fire ExtinguisherN.S

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required.DSR 201817.3.1

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.DSR 201817.3.2

speaker cable Two pair, 2-core, 1.5 sqmmDSR 201817.5.3.2

Supply, installation, testing and commissioning of 120 liters Seamless Cylinder ( Or as per Calculation) with valve capable of withstanding pressure of 42 bar at 50 dec c Calculation, Cylinder / PESO / CCOE Approved.N.S

Supply, installation, testing and commissioning of Pressure Gauge +Low pressure supervisory switch. Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of SINORIX 1230 / FM200 VDS approved system. Gas calculation software should be VDS or UL Listed. Make (Kidde/Hochiki/Siemens/Feuerx)N.S

Supply, installation, testing and commissioning of Electromagnetic Actuator. The actuator should be capable of withstanding pressure at least of 90 bar. UL/VDS listed.Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Manual Actuator. The actuator should be capable of withstanding pressure at least of 100 bar at 50 deg c. UL/VDS listed.Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Pneumatic actuator. The actuator should be capable of withstanding pressure at least of 100 bar at 50 deg c UL/ VDS listed. Make(Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Flexible Discharge Hose with minimum bending radius of 125mm and brusting pressure should be more or equal to 180 bar. UL/VDS listed. Make idde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Flexible Actuation Hose with minimum bending radius of 75mm and brusting pressure should be more or equal to 660 bar. UL/VDS listed. Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Discharge Nozzle. The nozzle should be capable of handling at least 176 bar at 50deg c .Ul/ VDS Listed. Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Check Valve UL/VDS listed. Make Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Flow Switch . Make (Kidde/Hochiki/Siemens/Feuerx).N.S

Supply, installation, testing and commissioning of Manifold complete for making header of gas cylinders.N.S

Supply, installation, testing and commissioning of Wall mount kitN.S

Supply, installation, testing and commissioning of 2 Zone Gas Release panel with release module and battery backup. Make (Kidde/Hochiki/Siemens/Feuerx/ Ravel).N.S

Supply, installation, testing and commissioning of Abort Switch. Make (Kidde/Hochiki/Siemens/Feuerx/ Ravel).N.S

Supply, installation, testing and commissioning of M.S. Seamless pipes as per ASTM A 106 Gr. B, schedule 40 with necessary fittings. Make jindal, MSS, TATAN.S

VESDA server grade detectors Make Xtralis, SiemensN.S

12V 2 Amp Power Supply Unit with battery back up for above Detector. Make Xtralis, SiemensN.S

End CapN.S

T Joints & L Bends for sampling point networkN.S

Sampling Pipe Smooth bore PVC Pipe 21mm ID and 25mm ODN.S

Sampling point labelsN.S

Flash HooterN.S

2 core 1.5 sqmm FRLS armored cableN.S

SUB HEAD (III) TELEPHONE AND NETWORKING

Providing, fixing supplying, termination & certification of INTERNET networking . The item mentioned shall include the cost for laying Cat 6 UTP wire of in existing conduits for the wiring & it shall be such that each point has a dedicated single CAT 6 wire from the wall outlet to the patch panel.The rates quoted shall include the cost of termination of CAT6 cable in the wall sockets & patch panel including the cost of certification by network engineer using a penta-scanner , ferrulling of every point on both sides the contractor will have to provide the network certification in writing. Nothing extra shall be paid for on account of termination, crimping, certification etc. complete in all respects as desired by Engineer Incharge. The following items will be got exectued as under.

Supplying,Installation,Testing and Commissioning of I/O Modules Complete with Box,RJ-45 Socket,Front Plate as per the Satisfaction of the Engineer InchargeN.S

Supplying,Installation,Testing and Commissioning of I/O Modules Complete with Box,RJ-11 Socket,Front Plate as per the Satisfaction of the Engineer Incharge.N.S

Supplying and Fixing of Following sizes of PVC Conduit along with Accessories in surface/Recess including painting in case of surface conduit,cutting the wall and making good the same in case of recessed conduit as required.

25mm PVC Conduit

Supplying and Drawing of UTP4 pair CAT-6 LAN cable in the existing surface/Recessed Steel/PVC Conduit as required .N.S

Supplying and drawing 2 pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/PVC conduit as required.N.S

Supply, Installation, Testing and Commissioning of Semi managed 24 port POE , complete as per specification and as desired by EIC, N.S

Supply & Erection of lockable 9/12 U rack with 5A strip and two fan for distribution, mounting of patch panels, hubs, switches etc,, complete as per specification and as desired by EIC,Make : N.S

Supply & Erection of CAT 6, 24 port Jack panel for termination of CAT6 cable,Testing & certification of the network with Omni/Penta Scanner of each Cable, Make : N.S

Supply & Erection of Cat-6, 1Mtr Patch Cords complete as per specification and as desired by EIC,.N.S

Supply, installation, testing and commissioning of Junction Boxes/DB-50 Pairs with Original Krone module and Back Mount Frame and have Lock -n- key, complete in all respect as per specification and desired by EIC N.S

Supply, installation, testing and commissioning of 10 Pair jelly filled armoured cable of 0.5mm of each Pair Telephone Cable in the existing surface/ recessed steel/ PVC conduit, complete in all respect as per specification and desired by EIC N.S

Supplying,Installation,Testing and Commissioning of 40 Inches Full H.D LED Display Monitor as per the Specifications attached.N.S

Supplying of 16 Channel Network Video Recoder(NVR) as per the Specifications Enclosed with a Hard Disk Memory of 8 TB Capacity(SONY/HONEYWELL/BOSCH)N.S

Supplying,Installation,Testing and Commissioning of 2 Mega Pixel Full High Definition Weather Proof Bullet Camera.N.S

Supplying,Installation,Testing and Commissioning of 2 Mega Pixel Full High Definition Dome camera.N.S

SUB HEAD (IV) PLUMBING AND SANITARY

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 4/6 litre low level white flushing cistern, including flush pipe, with manually controlled device with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. .N.S

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:N.S

White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot restsN.S

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass Centre Hole Basin Mixer(01 Nos), 32 mm C.P. brass waste of standard pattern(01 Nos), Pedestal (01 Nos) including painting of fittings and brackets, cutting and making good the walls wherever required. N.S

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :N.S

510X1040MM BOWL DEPTH 250MM

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin With Fixing Accessories Set

Providing and fixing Urinal Partition/Division Plate.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backingN.S

Rectangular shape 453x357 mmN.S

Providing and fixing toilet paper holder with Flap made out of C.P Brass

C.P Brass

Providing and fixing C.P Brass Soap Dish.

Providing and fixing health faucet with hose pipe for european water closet complete in all respect of approved quality

Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws . N.S

Providing and fixing C.P brass bib cock with Auto closing System with Built in control Cock with Wall Flange of approved quality N.S

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser/cisterns points. N.S

15 mm nominal bore

Providing and fixing C.P. brass Single Lever Basin Mixer with 450 mm braided connection pipe. N.S

15 mm nominal boreN.S

Providing and fixing C.P. brass bottle trap for wash basin including CP waste fittings complete 32 mm dia complete in all respect of approved quality. N.S

Providing and fixing C.P. brass Wall Mixer with Provision of Over Head Shower with 115 mm long bend. N.S

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.N.S

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B N.S

75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B N.S

160 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B N.S

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings required.Makes:- Astral/SFMC/Finolex N.S

PE - AL - PE COMPOSITE PRESSURE PIPES

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.

Concealed work, including cutting chases and making good the walls etc.

1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.

Internal work (Exposed on wall)

2532 (32 mm OD) pipe

3240 (40 mm OD) pipe

4050(50 mm OD) pipe

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.

External work

4050 (50 mm OD ) pipe

Providing and Fixing of Thermal Insulation for Hot Water Lines made out of Flexible Elastomeric Foam of Closed Cells Structure Having a Thermal Conductivity of 0.038 W/m.K at 200 Deg C water Vapour Permeability of Cu.m 5000 as Required including accessories i.e Adhesives/Tape on all Joints as per the satisfaction of the Engineers Incharge.

1620 (20 mm OD) pipe

Providing and fixing unplasticised PVC connection pipe with brass unions:

45 cm length

15 mm nominal bore

Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks

Constructing masonary chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement: 4 coarse sand) with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cenment:5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design With F.P Bricks.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m(For All Kinds of Soil)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

160 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

200 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and filling sand of grading zone V or coarser grade all-round the Composite Pipes in external work & lay dry brick over sand layer to protect the pipe.

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

160 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

200 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Supply, Installation of PVC Gully Trap of Size 110 mm Makes:-Astral/SFMC/Finolex

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

50 mm Diameter

40 mm Diameter

32 mm Diameter

25 mm Diameter

Providing and fixing on wall 50 LTRS Electric Geyser with ABS Body.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank(2000 Ltrs), ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

Making soak pit 2.5 m diameter 3.0 metre deep with 45x45 cm dry brick honey comb shaft with bricks of class designation 75 and S.W. drain pipe 100 mm diameter, 1.8 long complete as per standard design.

With F.P.S. bricks

Constructing septic tank, of size 5.0mx2.5mx1.4m approx. height(Height to be fixed as per site requirement i.e. below invert level of last manhole (1.5 m water depth) , in B/W, 350/230 mm thick ( minimum) walls and 400 mm

SUB HEAD (V) HVAC

VARIABLE REFRIGERANT FLOW/ VARIABLE REFRIGERANT VOLUME SYSTEM

Supply, Installation, Testing and Commissioning of Variable Refrigerant Flow/ Variable Refrigerant Volume modular type air- conditioning system suitable for Heating/Cooling by 100% inverter driven capacity control compressor complete with indoor and outdoor units with individual controller , fittings etc. including full charging of R-410A refrigerant gas complete with operating range down to -20 deg c in heating mode. Make : Toshiba/ Mitsubishi Electric /General /Daikin/Equivalent AIR COOLED VRF/ VRV OUTDOOR UNITS Supply Instalaltion, testing and commissioning of Modular type outdoor units alongwith base frame/Outdoor stands as recommended by OEM equipped with highly efficient scroll / DC Twin Rotary compressors all with inverter type compressors special heat exchanger, low noise condenser fan, auto check function for connection error, auto address setting and capacity as mentioned below.

18 HP of any combination with high efficiency

10 HP of any combination with high efficiency

Indoor Units:Round Flow Cassette Type

Supply, Installation, testing and commissioning of Cassette Type Indoor units equipped withl, pre-filter, fan section with suitable static fan, multispeed motor, coil section with DX coil, outer cabinet, drain pan, drain pump, insulation, pipe connections, variable evaporative temperature control etc. of various capacities as per specifications and drawings, All indoor Units should have force shut option to connect with fire alarm or key card adaptor, so that the unit automatically stops in case of fire or key card removal.N.S

Cassette Type Indoor Unit - 1.6 HP

Cassette Type Indoor Unit - 2.5 HP

Cassette Type Indoor Unit - 3.2 HP

Heat Reclaim Ventilation Units (HRV)

Supply, Installation, testing and commissioning of Heat Reclaim Ventilation (HRV) with airflow rate 950 CMH and external static pressure 135 pascal for the fresh air circulation.N.S

Heat Reclaim Ventilator - 950 CMH, HeatingCapacity 10.92 KW

Supply and installation of Refrigerant Piping Y-Joints as required to connect the above outdoor units and indoor units. ( liquid and gas line as one set)N.S

Supply and installation of Refrigerant Piping HEADER -Joints required to connect the above outdoor units and indoor units. ( liquid and gas line as one set)N.S

Supply, Installation, testing and commissioning of Corded remote

Supply, Installation, testing and commissioning of Centralised Remote Controller which can control maximum 64 groups of indoor units, malfunction code display in the screen, .N.S

Drain Piping:

SITC of PVC (Minimum 15 Kg/Sqcm pressure rated) Drain Water Piping complete with fittings (elbows, tees, reducers, sockets etc.), supports, jointing and any other item required to make the system complete. Nominal Diameters of Pipes in mm as indicated below:N.S

25 mm ( with 9 mm Class- O XLPE)

32 mm ( with 9 mm Class- O XLPE)

40 mm ( with 9 mm Class- O XLPE)

50 mm ( with 9 mm Class- O XLPE)

Copper Refrigerant Piping with Insulation for VRV System:

SITC of Copper Refrigerant piping for VRV / VRF System complete with fittings, supports, jointing, insulation with class O -XLPE , gas charging & commissioning as per specifications, all accessories as per specifications and any other item required to make the system complete. Nominal Dia in mm OD as indicated below : N.S

34.9 ( with 19 mm insulation )

28.6 ( with 19 mm insulation )

25.4 (with 19 mm insulation)

22.2 ( with 19 mm insulation )

19.1 ( with 13 mm insulation )

15.9 (with 13 mm insulation)

12.7 ( with 13 mm insulation )

9.5 ( with 13 mm insulation )

6.4 (with 13 mm insulation)

CONTROL CABLING

Providing & fixing control cum transmission wiring of 2 core x 1.5 sqmm copper in suitable conduits between indoor units and outdoor units and indoor units and remote controllers.N.S

Supply, installation, balancing and commissioning of fabricated at site GSS Sheet Metal Rectangular/Round Ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as requiredN.S

Thickness 0.63 mm sheet

Thickness 0.86 mm sheet

Supply & installation of Acoustic Insulation complete with XLPE / Rubber as per approved drawings and specifications of following sheet thickness complete as requiredN.S

Thickness 25 mm

Flexible Duct with SpigotN.S

100 mm Dia.N.S

75 mm Dia.N.S

Disc ValvesN.S

100 mm Dia.N.S

75 mm Dia.N.S

SUB HEAD (VI) FIRE FIGHTING

PIPES & ACCESSORIES

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.DSR 20186

150 mm. DiaDSR 20186.2

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :DSR 20187

25 mm diaDSR 20187.1

40 mm diaDSR 20187.3

50 mm diaDSR 20187.4

65 mm diaDSR 20187.5

80 mm diaDSR 20187.6

100 mm diaDSR 20187.7

150 mm diaDSR 20187.8

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :DSR 20189

Single headed GunmetalDSR 20189.1

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :DSR 201810

Single headed GunmetalDSR 201810.1

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :DSR 201811

150 mm diaDSR 201811.6

80 mm diaDSR 201811.4

100 mm diaDSR 201811.5

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.DSR 201813

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :DSR 201816

Gun MetalDSR 201816.1

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.DSR 201817

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :DSR 201819

2 way-100 mm dia M.S. PipeDSR 201819.1

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.DSR 201820

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :DSR 201821

Upright SprinklerDSR 201821.2

Pendent SprinklerDSR 201821.1

Horizontal side wall sprinklerDSR 201821.3

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.DSR 201822

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.DSR 201823

100 mm dia.DSR 201823.1

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :DSR 201824

100mm diaDSR 201824.2

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520 b) Suitable HP squirell cage induction motor TEFC type suitable for peration on 415 volts, 3 phase, 50 Hz, ACsupply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation,conforming to IS-325.(c) M.S.fabricated common base plate, coupling, coupling guard, founation bolts etc.as required.(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.DSR 20184

450 lpm at 35 m HeadDSR 20184.2

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :DSR 201814

150 mm diaDSR 201814.7

Providing, installation, testing and commissioning of stainless steel Y-strainer 150 mm fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.DSR 201815.3

Providing and placing on terrace (at all floor levels) polyethylene water storage tank(5000 Ltrs), ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and verflowpipes but without fittings and the base support for tank. N.S

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :DSR 201818

Gun metalDSR 201818.1

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.DSR 2018

1000mmDSR 201825.2

Providing and fixing Weather proof hose cabinets for yard hydrant fabricated from 16 g MS sheet with full glass door and locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe and one fireman's axe. The cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 mx 0.25 m).N.S

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.N.S

Providing and fixing fully glazed MS fully welded construction double leaf door shutter for fire hydrant station fabricated from MS 50x50x6 mm angle iron frame, fixed to wall and hinged MS 40x40x5 mm angle iron door shutter with required MS sash bars for glazing complete with locking arrangements, stove enamelled fire red finish with 'FIRE HYDRANT' written in front.N.S

SUB HEAD (VII) Elevator

Supply, Installation,Testing and commisioning of 13 Passenger Lift with the following Specifications CAPACITY (kgs) :884 Kg, 13 persons SPEED (mps): 1.5 mps RISE (m ) :8 m(Appx) STOPS: 2 Stops With (all opening on the same side) DRIVE :VF Regenerative (Closed Loop) MACHINE :PM Gearless (Located in shaft on top of guide rails) "CAR FINISH• : Rear Mid Panel = SS HAIRLINE Rear Corner Panels = SS HAIRLINE Side Mid Panels = SS HAIRLINE Side Corner Panels = SS HAIRLINE Front Panels = SS HAIRLINE type " FALSE CEILING FINISH: SS HAIRLINE HAND RAILS :Stainless Steel Mirror Finish Handrails on rear car panels VENTILLATION:Cross flow fan FLOORING:Vinyl Tiles DOOR OPERATOR:DC Door Operator "STANDARD FEATURES:Anti-nuisance Car Call Protection Independent Service (for Duplex only) Overload Device Nudging Emergency Firemen’s Service Emergency Car Light Unit Infrared Curtain Door Protection Door Time Protection Emergency Alarm Button Extra Door Time of Lobby & Parking Door Open/Close Button Manual Rescue Operation Belt Inspection DriveAuto Fan Cut Off "

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.DSR 20184.6

50mm (W) x 50 mm (H) x 1.6mm wide cable tray perforated typeN.S

300 mm width X 50 mm depth X 1.6 mm thicknessDSR 20184.6.4

600 mm width X 50 mm depth X 2.0 mm thicknessDSR 20184.6.7

900 mm width X 62.5 mm depth X 2.0 mm thicknessDSR 20184.6.13

SUB HEAD (VIII) Conference Audio Vedio

Supply installation testing & commissioning The System 2-Way wall mount Speaker System with 6 inch lf & 1 inch hf compressor driver unit only with 100 watt rms power continious and max spl of minimum 121 db ; with paint finish .N.S

Supply installation testing & commissioning of class h or d power amplifier with 2 x 450 watt rms power at 4 ohms per channel for speakers .N.S

Control Unit:- Powers up to 50 discussion units, Cascade capability to handle up to 300 discussion units, Conference mode: Free talk, request to talk and full remote,2 Mic/Line In + 1 Aux In + 2 Return In, Built-in feedback suppressor and digital audio processing (DSP), Gain sharing algorithm substantially reduces the risk of feedback while maintaining a natural sound. N.S

Delegate Units:- Crystal-clear, 24-bit digital audio processing with 12-band feedback suppressor, Easy plug-and-play operation,discussion units, integration units, and interpretation units (max of six INTs) can be connected, in either daisy chain or ring topology, to each control unit with long gooseneck microphone 320 MM Length. N.S

Chairman Unit:- Crystal-clear, 24-bit digital audio processing with 12-band feedback suppressor, Easy plug-and-play operation, A total of 100 ATUC-50DU discussion units, ATUC-50IU integration units, and ATUC-50INT interpretation units (max of six INTs) can be connected, in either daisy chain or ring topology, to each ATUC-50CU control unit With long gooseneck Microphone 430MM Length.N.S

Supply Installation testing & Commissioning of Gooseneck cardioid Microphone with minimum gooseneck length of 16.46 INCH MM , polar pattern Cardioid, Frequency Range 70-16000 Hz, Sensitivity18mV/Pa, Impedance >2000 ohms ; with on/off base along .N.S

Supply installation testing & commissioning of Cordless Handheld Microphone with UHF frequency .N.S

SITC of Multipoint video conferencing system with 3 + 1 Location library Supports with Full HD resoliution , Supports multiple HD pan-tilt-zoom cameras .N.S

SITC of Professional display panels with 60 inch size with full Hd resolution of 1920 x 1080 ; with view angle of 178 degree x 178 degree .N.S

SITC of Professional display panels with 86 inch size ; with 4 k resolution with view angle of 178 degree x 178 degree.N.S

AV switcher with 4 inputs and 4 outputs along all in outs with external cards of inputs along outputs as required for functioning .N.S

Wireless presentation system with 2 dongle along processor for wireless presentation in conference room Display Port, Single link DVI-I , VGA (via included convertor, highest resolutions only with reduced blanking) ,In "Dual screen" mode, connection can occur either through DVI and Display Port, or through VGA and Display Port..N.S

Mini Size Extender set consists of a Transmitter and a receiver. Hdbase T technology is used to transmit high - resolution 1080p/4k signal to the receiver up to 70/40m via a cat5e/cat6A cable . N.S

Supply Installation testing & Commissioning of main SYSTEM RACK - M.S. Rack with Power indicator, power sockets and isolator fitted duly prewired to accommodate Control Room equipments for in house equipments with cooling fn at back gate e.g. Amplifiers, Controller, Equalizer etc as required.N.S

Supply Installation testing & Commissioning of PATCH CORDS ( for SYSTEM INTERCONNECT ) - High grade professional low-noise bable, 2-Core High conductivity PVC insulated in PVC jacket,shielded Copper Cable with di-electric insulator to prevent RF interference with necessary XLR male/female connectors EP Jacks / RCA Jacks etc as required.N.S

Supply, laying & Fixing of Microphone Lines High grade, profeional, Low-noise, 2-Core High conductivity PVC insulated in PVC Jacket, Shielded, Copper Cable with di-electric insulator both end with XLR m/f connector as required .N.S

Supply, laying & Fixing of Speaker Lines: 2-Core, High definition Speaker Cable, PVC insulated in PVC jacket laid in existing conduits as required.N.S

Cable Cubby /Patch Panel, surface access enclosue, openable with press down on the top the enclosure with one data input on HD 15 connector , one video input on RCA connector , two cat 6 RJ 45 connector for LAN .N.S

Supply laying & fixing of Cat 6 Shielded cables for the Video wall and pannel .N.S

Supply & laying of HDMI cable with 20 meter length .N.S

Supply & laying of HDMI cable with 1.5 meter length .N.S

SUB HEAD (IX) EXTERNAL ELECTRIFICATION

Supplying and Installing Following Size of Perforated G.I Cable Tray with Perforation not more than 17.5% in convenient Sections ,joined with connectors ,suspended from the Ceiling including bolts and Nuts ,etc as required.

900 mm (W) x 50 mm (H) wide cable tray Ladder Type

The 11kV Outdoor Package Sub-Station shall be consisting of following ,N.S HT SWITCHGEAR 11kV 630Amps 21kA for 3 sec. SF6 insulated Extensible Compact switchgear (Type DV) One No. of Fixed Manual Vacuum Circuit Breaker in 2.5 mm SF6 insulated Robotically welded Stainless steel enclosure of IP67 class of protection with series trip,self powered microprocessor based numerical over current and Earth Fault (IDMT+Inst.) relay protection 1 incomer 2 outgoing. The Panel to be provided with the Battery Backup of 180 AH battery including the Charger for C&R Panel. Interconnection between HT switchgear and transformer shall be using 1Cx3x95 sq.mm Aluminium unarmorured XLPE Cable. (Make: ABB India Limited/Siemens/Schneider/Equivalent)(01 Nos) Relay shall be Ashida Make Model No: ADR141S without communication port(01 Nos) Protection CT Ratio of CTR: 40/1 Amps, 2.5VA 10P10(03 Nos) Manometer(01 Nos) TRANSFORMER 630KVA 11KV/433V DYn11 ONAN Level II Copper wound Oil Filled Hermatically Sealed Transformer with corrugated wall, without conservator type of design & Top normal porcelein Bushings for HT & LT with Off Load Tap Switch having range +2.5% to -12.5% @2.5%. Temp Rise in Oil/Winding shall be 40/50 Deg Cel respectively.With Latest IS 1180 level 2)(01 Nos) Make: Schnider, ABB or equivalent. Oil Temperature Indicator with Alarm and Trip Contact(01 Nos) Winding Temperature Indicator with Alarm and Trip Contact(01 Nos) LVS PANEL-1250 AMPS ALUMINIUM BUSBAR 100% for Phase and 50% for Neutral (CURRENT DENSITY-1 Amps/Sq.mm) INCOMING 1250Amps 433V 4P 50Hz 50KA Manual Fixed (MF) Type Air Circuit Breaker (ACB) with Thermal magnetic release. ( Make: ABB) OUTGOING 1250Amps 433V 4P 50Hz 50KA Manual Fixed (MF) Type Air Circuit Breaker (ACB) with Microprocessor release.(01 Nos) OUTDOOR ENCLOSURE Outdoor type enclosure having modular construction of Galvanised Sheet Steel of 2 mm thickness for Load Bearing and 1.5 mm for Non Load bearing with 4 mm base frame.The Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP23 degree of protection for Transformer compartment. The enclosure exterior shall be painted with Polyurathene Painted /Powder coated ( colour Light Gray & D.A.Gray ). Each compartment will be provided with the door and pad locking arrangement. The Compartment illumination lamp with door operated switch shall be provided for MV and LV Compartment. (01 Set) INTERCONNECTION AND EARTHING Interconnection Between HT switchgear & Transformer using 1Cx3x95Sq.mm XLPE Single core ALuminium cable & Interconnection between Transformer & LT switchgear using suitable sectional Aluminium Busbars. Internal earthing connections by using 50x6 mm GI Strips. (01 Set)

Supply,installation with foundation as per approved Drawing 11 Mtr SP-53 M.S PoleN.S

Supply,installation of Structural Steel as per Standard Approved DrawingN.S

Supply,Installation and Commissioning of 11 KV Air Break Switch(400 Amps).N.S

Supply,Installation of 11 KV L.A 10 ka (Station Class).N.S

Supply,Installation of 11 KV HG Fuse Unit .N.S

Supply,Installation of Disc Insulator(B&S)70 KN suitable for 100 sq.mm Triple AAAC.N.S

Supply and Installation of B&S Hardware Fittings.N.S

Supply and Installation of 100 Sq.mm AAAC Triple AAAC.N.S

Supply,Installation of 11 KV Pin Insulator suitable for 100 sq.mm Triple AAAC.N.S

Supply and Erection of 150 mm Dia. Heavy Class G.I Pipe for the Cable Protection.N.S

Supply,Installation and Commissioning of 11 KV Meter with suitable size Out door Type combined C.T and P.T's of 40/1A Accuracy Class 0.5 S Burden 100 VA 11 KV/Root3/110 V /Root3N.S

Design, manufacture, supply, loading & unloading, erection, testing and commissioning of 415V, 320 KVA DG Set with alternator complete with acoustic enclosure, all fittings and accessories as required/ as specified in the technical specification Make: Sudhir, Kirloskar or Equivalent. .N.S D.G SET 320 KVA ) >> Radiator Residential type silencer >> Anti-vibration mounts Battery and charger Dynamo Engine instrumentation Panel Other accessories as Required

Supply, laying, testing & commissioning of 1.1 kV grade, armoured, PVC insulated multi core Cu conductor LT control Cable including necessary cleats, clamps end connection with gland & termination etc. for DG set

4C x2.5 sq.mm (YWY)

3C x 2.5 sq.mm (YWY)

4C x4sq.mm (YWY)

12 C x 2.5 sq.mm

Supply and connect fuel pipe of M.S medium class pipe with flange between 990 ltrs. Fuel tank and engine. Of suitable dia

Supply, receive at site, store, unpack, assemble and connect Exhaust pipe with Class-B MS pipe with flanges. Vendor has to confirm Pipe sizes.

8" for horizontal pipe

14" for vertical pipe

8" cladding

14" cladding

Silencer cladding

Supply & Fabrication with steel sections and erection of MS base frames , MS angle channels , flat etc for supporting various items of equipment Panel , Bus ducts , adaptor boxes addition support for proper cable termination, cable trays, etc. Including welding, bolting, chipping , grouting etc, including applying one antirust coat of approved primer and two finished coats of approved paint , breaking and finishing of walls, floors etc. The scope is inclusive of minor civil work as required, supply & installation of GI hardware materials, consumables, anchor fasteners, tools & tackles and necessary labour with supervision but not limited to, and complete as per approved drawings, specification and directions of Engineer-In-Charge. Scope also includes contractor's own lifting and transporting arrangement.

Supply,Installation of 3 Mtr 80 mm G.I Pole with Foundation in conceret mix of 1:2:4 along with muffler upto a height of 450mm and PVC Junction Bos having the faility to house 4 way Bekellite strip and 6 A MCBN.S

SITC of Integral Pole Mounted Decorative LED Post Top with Spherical Shade polycarbonate Diffuser and IP:65 Protection Model No. Wipro(LP-07-431-xxx-57-CL) 35 WattsN.S

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.N.S

SITC of IP: 66/IP:67 PVC Junction Box having the Facility to house 4 way Bakellite strip for connection to the spike light.(Make:- Hensel)N.S

Supplying and Laying of 1 No. DWC High Density Poly ethylene Pipe having Corrugation on Outer wall and Plain surface inner wall Conforming to IS: 14930 Part-1 and 2 Complete with accessories for Protection of 1.1 KV Grade under Ground cable Directly in Ground at a Depth of 50 CM including excavation and Refelling the Trench Etc.as Required .N.S

Size 63/50mm

SITC of All in One Integrated Solar Street Light 90 W on 7 Meter Octagonal Pole with 3 day Autonomy.

Supplying,Installation and Testing of 50 mm Cu. Pipe Filled with Crystalline conductive Mixture with Copper Strip of Size 32 mm x 5 mm of Length 2 mtr with Ecofriendly Backfill Compound 50 Kg.Makes:- nus/Ashlok/GMAXX

Providing and Fixing 50 mm x 6 mm Copper Strip in 80 mm dia. G.I Pipe FRL Earth Electrode including connection with Brass nut ,bolt,spring,washer,excavation and refilling etc. as required.

Supplying, Installation and Testing of 50 mm G.I. Pipe Filled with Crystalline conductive Mixture with G.I Strip of Size 40 mm x 6 mm of Length 2 mtr with Ecofriendly Backfill Compound 50 KgMakes:- Genus/Ashlok/GMAXX

Providing and Fixing 75 mm x 10 mm G.I Strip in Earth Electrode including connection with G.I nut ,bolt,spring,washer,excavation and refilling etc. as required.

SUB HEAD (X) EXTERNAL FIRE FIGHTING

PUMPS

Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads.DSR 20181

2850 lpm at 88 m Head DSR 20181.1

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric tarting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office redcolour etc. as required.M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required.Suitable cement concrete foundation duly plastered and with nti vibration pads.DSR 20182

2850 lpm at 88 m HeadDSR 20182.1

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.DSR 20183

180 lpm at 88 m Heada

150 mm. DiaDSR 2018 6.2

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :DSR 20187

80 mm diaDSR 20187.6

150 mm diaDSR 20187.1

200 mm dia (wall thickness 6.3 mm)DSR 20187.9

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :DSR 201810

Single headed GunmetalDSR 201810.1

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :DSR 201811

80 mm diaDSR 201811.4

200 mm diaDSR 201811.7

150 mm diaDSR 201811.6

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.DSR 201813

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :DSR 201816

Gun MetalDSR 201816.1

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :DSR 201819

4 way - 150 mm dia M.S. PipeDSR 201819.2

Providing, fixing, testing and commissiong of double flanged vertical air vessel fabricated from 10mm MS plate with dished ends from 10mm MS plate, outside with one coat of primer and two coats of synthetic enamel paint of approved shade, complete with approved quality of pressure switches, pressure gauge and all other required accessories to operate commonly main fire pump, sprinkler pump and Jockey pump at drop of pressure, automatically at required pressure setting :N.S Recommended dia. : 450mm Height of shell : 2000mm Working pressure : 5.5 kg/cm2 Test Pressure : 10 kg/cm2 Panel For Under Ground Fire Pumps

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.DSR 201822

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :DSR 201814

150mm diaDSR 201814.7

Providing, installation, testing and commissioning ofstainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.DSR 2018

200mm diaDSR 201815.4

Providing and fixing of Pressure Guage.N.S

Construction of Under Ground Fire Tank of 200 KL Capacity @depth 3 mtrN.S

Construction of Under ground Fire Pump Room as per the Drawings @ depth 3 mtrN.S

SUB HEAD (XI) EXTERNAL PLUMBING

Supply,Installation,Testing and Commissioning of Open Well Submersible Pump(1 W +1 S ) with a Discharge of 20 Cu.m/hr @ Head of 65 Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel. N.S

Supply,Installation,Testing and Commissioning of Open Well Submersible Pump(1 W +1 S ) with a Discharge of 1 Cu.m/hr @ Head of 15 Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel. N.S

Providing and fixing Polyethelene-Aluminium-Polyethelene (PE-ALPE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 0C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer in charge.N.S

External work

6375(75 mm OD ) pipe

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m(For All Kinds of Soil)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc. complete including jointing.N.S

200 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Providing and filling sand of grading zone V or coarser grade all-round the Composite Pipes in external work & lay dry brick over sand layer to protect the pipe

200 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

Constructing masonary chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement: 4 coarse sand) with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement: 2 coarse sand:4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cenment:5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement :3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design With F.P Bricks.N.S

Environmental Management and Safety

Design and providing of Project Information Board ( one during construction and another after completion of work) in sheet steel (4mm thick) and all supports of 2 nos MS angle 50 x 50 x 6 mm of height 1.5 mtrs, including fixing in M 15 Concrete blocks of size 0.30 x 0.30 x 0.60 m and maintenance during the entire project. Minimum of board size 2 meters X 1.5 meters, with necessary information in English and Urdu written in White paint with blue backgorund on the board. The board details and the required information will be furnished by the Engineer. The complete design and information should be approved by the Engineer in Charge.

Cost towards environmental compliance. The contractor should carefully read the Environment management plan and assess the items and scope of work. The following items shall be the responsibility of the contractor during execution of this project. These items are related to environment management plan for the project.

Provision, installation and maintenance of cautionary/warning signage, including diversion boards as per IRC specifications (SP:55, 2014) near operational areas, including cost of boards and other materials required for fixing, shifting charges from one place to another with all incidental charges leads, lifts and all taxes as applicable from time to time and as specified by Engineer-in-charge.

Wet type portable toilet (MS fabricated) 2 seats (1 for men and 1 for women with separate entrances), fitted with 2000 liters capacity overhead tank and 500 liters capacity bottom tank, fitted with Indian type of pot with other facilities such as tap, lighting and ventilation; and sludge tank of capacity 1000L, and stationed at a suitable place in or within 100 metres from work front. Includes cost of water, cost for emptying of bottom tank through mobile suction machine, shifting cost of mobile toilet from one operational area to another, attendent cost for looking after cleaning and operation of the toilets, all materials and labour charges, all incidental charges, leads, lifts and all taxes as applicable from time to time and as specified by Engineer-in-charge.

Providing of mobile drinking water counter/kiosk, fabricated from stainless steel with 300 liters capacity, with two taps and with bottom tank (300 litre holding capacity) to collect waste water and stationed at a suitable place within 100 metres from operational area, with one common attendant for both mobile toilet and drinking water kiosk. Cost includes charges for emptying bottom tank through suction machine, shifting cost of the kiosk from one operational area to another area, attendent cost for looking after cleaning and operation, all materials and all labour charges, all incidental charges, leads, lifts and all taxes as applicable from time to time and as specified by Engineer-in-charge

Cost towards first aid and emergency response arrangements in the camp, plants and worksites (including fire and electrical safety provisions)

Cost towards periodic health check-ups once in three months for all construction workers

Cost of environmental monitoring during entire construction period in line with parameters and frequency specified in the EMP ( 6 monthly intervals)

M M SHAWL ENGINEER AND CONTRACTORS PVT LTD

N S Associates PVt Ltd