Renovation of Police qtr

Amount

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddingin cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarsesand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVCfoam sheet, mitred at corners and joined with 2 Nos of 150 mm longbrackets of 15x15 mm M.S. square tube, the vertical door frame profilesto be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDMrubber gasket weather seal to be provided through out the frame. Thedoor frame to be fixed to the wall using M.S. screws of 65/100 mm size,complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing factory made panel PVC door shutter consisting offrame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S.frameshall have a coat of steel primers of approved make and manufacture.M.S.frame covered with 5 mm thick heat moulded PVC 'C' channel ofsize 30 mm thickness, 70 mm width out of which 50 mm shall be flat and20 mm shall be tapered in 45 degree angle on both side forming stylesand 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flatand 20 mm shall be tapered in 45 degree on the inner side to form topand bottom rail and 115 mm wide PVC sheet out of which 75 mm shall beflat and 20 mm shall be tapered on both sides to form lock rail. Top,bottom and lock rails shall be provided both side of the panel. 10 mm (5mm x2) thick, 20 mm wide cross PVC sheet be provided as gap insertfor top rail & bottom rail, paneling of 5 mm thick both side PVC sheet tobe fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm(5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, andjoined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C'Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing

30 mm thick plain PVC door shutters

Providing and fixing plain multipurpose cement board(Hight pressuresteam cured) with suitable screws for cement particle board in ceilingetc. complete (frame work to be paid seperatately).

6 mm thick Cement fiber board as per IS: 14862

Providing and fixing precoated galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 gramsper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxyprimer on both side of the sheet and polyester top coat 15-18 micronsusing self drilling/ self tapping screws complete :

Ridges plain (500 - 600 mm)

Gutter (600 mm over all girth)

Painting with synthetic enamel paint of approved brand andmanufacture to give an even shade :

Two or more coats on new work

Distempering with 1st quality acrylic distemper (ready made) havingVOC content less than 50 gm per ltr. of approved manufacturerand of required shade and colour complete. as per manufacturer’s specification

One or more coats on old work

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete andstacking within 50 metres lead :

Of area 3 sq. metres and below

Dismantling roofing including ridges, hips, valleys and gutters etc.,and stacking the material within 50 metres lead of:

G.S. Sheet

Asbestos cement sheet

Providing and fixing powder coated aluminium work (minimumthickness of powder coating 50 micron) consisting of tee/ anglesections, of approved make conforming to IS : 733 in frames of falseceiling including aluminium angle cleats with necessary C.P. brass/stainless steel sunk screws, aluminium perimeter angles fixed towall with stainless steel rawl plugs @ 450 mm centre to centre andfixing the frame work to G.I. level adjusting hangers 6 mm dia. withnecessary cadmium plated machine screws all complete as perapproved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion holdfasteners to be paid for separately).

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :

Superior hard wood Cat-II(A)

Providing and fixing 35mm glazed shutter for windows with superior hard wood category II. Kiln seasoned and treated as per IS 401 using 10 kg/sqm (4mm) glass panes including oxidised M.S. butt hinges with necessary screws etc. complete.

Providing and fixing 35mm panelled, glazed or panelled and glazed shutters for doors including oxidised mild steel butt hinges with necessary screws with superior hardwood category No. II(A) kiln seasoned and treated as per IS: 401 including panelling with 12mm thick marine plywood (BWR) confirming to relevent specification with wooden cleats and block and as directed by Engineer in charge.

Providing and fixing in position eaves or facia board with 19mm thick PVC Board (30cm width) including fixing with nuts and bolts etc complete.

Providing wood work in frames , trusses, purlins, raftera etc swan and put up in position with klin seasoned and chemically treated superior hardwood Cat-II (A) :

Superior hard wood Cat-II(A)

Providing and fixing precoated galvanised iron profile sheets of brand TATA Blue Scope/ Everest or equivalent (size,shape and pitch of corrugation as approved by Engineer-in-charge)0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns. Sheet should have protective guard film of 25 micronsminimum to avoid scratches during transportation and should besupplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tappingscrews of size (5.5x 55 mm) with EPDM seal, complete upto anypitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and fixing 4 mm dia. Level adjusting hangers (Upto 2.5 m Length) adjusting hangers to roof truss by means of providing knot as per direction of Engineer-in-charge.

K KRISHNA RAO