SPL REPAIRS TO BLDG NO T48 AND ALLIED INFRA AND PROVN OF 06 X STABLES AND ALLIED WKS FOR 6 X HORSES AT DHRUVA EQUESTRIANS NODE DEN UNDER GE SOUTH UDHAMPUR

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in any type of soil etc complete all as directed.

Excavating over areas, n exc 1.5m deep and getting out in any type of soil, complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out in any type of soil complete all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layers not exc 25 cm in any type of soil complete all as specified and as directed.

Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4 sqm each and removing complete all as specified and as directed.

Taking down cement plaster of any description on brick/stone walls or concrete surfaces including racking out joints, hacking for key scrubbing down with water etc on walls and ceiling, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc. complete all as specified and as directed.

Dismantling Asbestos cement (corrugated or semi corrugated) sheets as in roof covering all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Demolition of brick or stone masonry including all necessary arches, pillars, quoins etc built in cement mortar complete all as specified and as directed.

M&L PCC1:2:4 using B0 (12.50 graded aggregate) for coping, corner of roof and similar work complete all as sepcified and directed.

M & L for PCC 1:4:8 Type D2 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for RCC M-25 (20mm graded aggregate) as in foundations footings, plinth beams etc all as specified & directed.

M&L for RCC M-25 (20mm graded aggregate) as in columns, pillars etc all as specified & directed.

S&F TMT bars upto 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required, including binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

M&L 40 mm thick cement concrete flooring 1:2:4 type B-1 using 20mm graded stone aggregate fishing even and smooth without using extra cement complete all as specified and as directed.

M & L 75mm the PCC 1:3:6 type C-2 as plinth protection, finished even and fair without using extra cement complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:6 complete all as specified and as directed.

M & L hardcore of broken stone or boulders of gauge exc. 63mm but n exc 100mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-2 using 40 mm graded stone aggregate as in channels and drains, foundation and similar work etc complete all as specified and as directed.

M & L for providing Precast RCC 1:2:4 type B1 using 20mm graded aggregate as in landings, cover slabs (for manholes etc.),chajjas, shelves and similar articles with plain faces set in CM 1:4 complete plain fair faces, including cham fers, weatherings, throat- ing etc. and setting in mortar complete with joints to match complete all as specified and as directed.

M&L for 75 mm thick PCC 1:3:6, type C-2 by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

M & L Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:4) including finishing the surfaces fair and even without using extra cement all as directed

M & L Rendering 10mm thick on brick or concrete surfaces of walls in CM (1:6) including finishing the surfaces fair and even without using extra cement all as directed

M&L rendering 10mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces & finishing the surface even & smooth without using extra cement complete all as specified & directed.

M & L for rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surfaces as on ceiling complete all as specified and as directed.

M&L for screed bed in cement mortar 1:6 complete all as specified and as directed.

M & L double charged glossy finished Vitrified tiles light Shade 8-10mm thick (square/rectangular) polished, of sizes 4 feet x 8 feet or 4 feet x 6 feet or as approved by Engr in Charge as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

M & L double charged glossy finished Vitrified tiles light Shade 8-10mm thick (square/rectangular) polished, of sizes 4 feet x 8 feet or 4 feet x 6 feet or as approved by Engr in Charge as in skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering/backing coat or fix with chemicals in CM 1:4 complete all as specified and as directed.

M & L for wall cladding tiles (Stone series or as approved by Engr in Charge) in vertical surface 300x600x7mm thick laid over 10 mm thick rendering/backing coat in CM 1:4, set and joint in neat cement slurry and pointed in white or colour cement to match complete all as specified and as directed.

M & L 18-20 mm thick granite (of any type) work( table rubbed and polished) in steps, jambs, pillars, window sills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite slab complete all as specified and as directed.

S & F 1st class hardwood (Teak/Sal) concealed frame or chowkats plain, solid, straight, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and as directed.

S&F 35mm thick Flush shutters, solid core construction, with BWR(boiling waterproof grade) plywood face panels, commercial type on both sides & one face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed. Make : Century/Greenply/Kitply/Archid Note : - (i) Teak/Walnut veneer and satin lacquered finish plus brass trim. (ii) all edges shall be sealed with hardwood lipping or PU sealer with polish.

S&F 1mm thick wood grain printed Sunmica/PVC sheet (Design as approved by Engr in Charge) fixed or laid on to flush doors by using rubber based adhesive, supplying & fixing at site as per specification complete all as specified and as directed.

S&F 3D adjustable concealed hinges of premium quality to hold weight 50-80 Kg as approved by Engr in Charge complete all as specified and as directed. Make : Hafele India/DormaKaba/Hettich

S&F recessaed/integated handle (flush handle or groove handle) of premium quality as approved by Engr in Charge complete all as specified and as directed. Make : Hafele India/DormaKaba/Hettich

S&F conealed door closure of premium quality as approved by Engr in Charge complete all as specified and as directed. Make : Hafele India/DormaKaba/Hettich

S&F magnetic lock & controller of premium quality as approved by Engr in Charge complete all as specified and as directedm. Make : DormaKaba EM-250/Hafele/Hettich

S&F RFID electronic lock of premium quality as approved by Engr in Charge complete all as specified and as directedm. Make : Yale/Godrej RFID

S&F acoustic and fire seal to reduce noise as approved by Engr in Charge complete all as specified and as directed. Make : ZeroNoise/Saint Gobain

S&F factory made uPVC white/coloured three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wire mesh shall be paid separately) Make : Fenesta/Yashpoly/Veka. (Note: (a) The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. (b) No payment shall be made to the contractor without purchase vouchers directly from manufacturer's and warranty certificate from manufacture.

Supply and fixing factory made uPVC white/coloured fixed glazed window/ventilator/Partition walls made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Make : Fenesta/Yashpoly/Veka. (Note: (a) The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. (b) No payment shall be made to the contractor without purchase vouchers directly from manufacturer's and warranty certificate from manufacture.

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube suppling and fixing in opening as per specification & drawing complete all as specified and as directed.

S & F factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm thick plain colour PVC sheet on back face, fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F 5mm thick toughened glass (Etching design on glass as approved by Engr in Charge) as in windows, partitions, doors and similar work including cutting to shape, drilling holes required complete all as specified and as directed.

S&F 12mm Toughened glass(etching design on glass as approved by Engr in Charge) as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes required including all accessories like 18" SS handle, floor machine, locking system and all connected accessories etc complete all as specified and as directed.

S&F brass 4 lever Mortice lock, vertical type, size 100 mm complete all as specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F stainless steel cold rolled butt hinges medium weight 100 mm long complete all as specified and as directed.

S&F 200 mm long stainless steel barrel tower bolt of extruded section complete all as specified and as directed.

S&F 450 mm length stainless steel handles fabricated type anodised complete all as specified and as directed.

10-12 mm thick gypsum boards seamless false ceiling including sunk or raised moulding or cop design as approved, moisture resistant, including GI hanging wires & frames with intermediate, perimeter channel ceiling channel, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rawel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface complete all as specified and directed by Engr-in-Charge. Note : (a) Design of ceiling board as approved by Engr-in-Charge. (b) GI grid/hanging system shall be of the same make as of false ceiling manufacturer

S&F solid PVC wall lining consisting of 5mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site including all fixing accessories like PVC frames/fillets etc on PVC frame, complete all as specified and directed.

M&L for 15mm thick screed bed in cement mortar 1:4 and applying one coat of neat cement slurry @ 3.00 kg/Sqm and applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polythylene film. Min wt of memebrane will be 3.5 kg/sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) complete all as specified and directed.

S&F Venetian blinds rolling type using fabric blinds of approved colour/ shade and pattern including operating arrangement such as chord/ thread, rolling arrangement/roller, counter weight, connecting chain etc., and necessary fittings complete all as specified and directed.

M&L for Almirah/cabinet/cupboard required size at site made out 18 mm thick one side decorative lamination sheet/sunmica consisting of carcass 18/20 mm thick PVC sheet/HDMR board & provn of shutters made out of 18mm thick one side decorative laminated PVC sheet all required brackets SS screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2 mm thick edge bonding tape or 90 degree edge bent finish, necessary drawer, openable shelve with frame work complete as per make and specification mention as per drawing with locking arrangement approved by Engr-in-Charge. Colour as approved by GE. (Make: Rajshree/Sintex or equivalent) Complete all as directed.

S&F PVC steel catcher of superior quality all as specified and directed by Engr in charge

S & F Hettich soft closer hinges of stainless steel premium quality complete all as specified and as directed.

Fancy type Brass handles 100mm size fixed with screws, complete all as specified and as directed.

S & F 30 mm width of flap Continuous (Piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding, eves board and similar work to wall fixed with self tapping screws all as specified and as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates to Fe-290 (Gde E- 165) complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and as directed.

S&F 4 mm dia galvanised steel wire 50 mm x 50 mm mesh made up in to mattresses or cages etc complete all as specified and as directed.

S&F in repair counter top vitreous chinaware wash hand basin (WHB) white size 550mm x 400mm complete including 32 mm dia chromium plated waste coupling, PVC waste pipe and cutting for pinning in ends of brackets in wall etc complete. Make : Jaquar Make :KUS-WHT-35601 or its equivalent in Hindware/Cera/Parryware

S&F in repair Sinks with draining board made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S&F 5 mm thick looking mirror of required size, fixed on walls with dash fasteners and chromium plated screws purposefully made to fix the glass by drilling hole in the glass complete all as directed.

S&F in repair Water closet single piece pattern coloured of size 370x695x795 mm as approved and complete all as specified and directed by Engr-in-Charge . Make : Jaquar Cat part No KUS-WHT-35851S300UF or equivalent in Hindware/Cera/Parryware

S & F in repair 15 mm dia WHB mixer chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and as directed. Make - Jaquar Cat No KUP-35011BPM or equivalent in Hindware/Cera/Parryware

S&F in repair 15 mm bore CP Bib tap complete all as specified and directed. Make : Jaquar Cat Part No CON 107KN and equivalent in CERA.

S&F in repair 15 mm dia Angle valves/ stop cock ,fancy type and chromium plated screwed down high-pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and as directed. Make - Jaquar Cat No KUP-35053PM or equivalent in Hindware/Cera/Parryware

M&L in repair for vitreous China urinal half stall type white incl waste pipe and connected accessories complete all as specified and directed. Make - Jaquar Cat No URS-WHT-13253O or equivalent in Hindware/Cera/Parryware

S&F in repair concussive push button taps of cast copper alloy, screwed for iron pipe and fixed complete all as specified and as directed. Make - Jaquar Cat No PRS-077 or equivalent in Hindware/Cera/Parryware

S&F in repair urinal spreader of CP any colour for fixing with 15mm dia pipe (minimum weight 60 gms) complete all as specified. Make - Jaquar Cat No URS-WHT-13253O or equivalent in Hindware/Cera/Parryware

S&F in repair Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe complete all as specified and directed. Make : Jaquar and equivalent .

S&F in repair chromium plated toilet paper holder complete all as specified and directed. Make : Jaquar Cat Part No ACN 1153N and equivalent in CERA/Parryware.

S&F in repair 600 mm long brass chromium plated towel rail fancy type complete all as specified and directed. Make : Jaquar Cat Part No ACN-1111NM and equivalent in CERA/Parryware.

S&F in repair soap dish complete all as specified and directed. Make : Jaquar Cat Part No ACN 1131N and equivalent in CERA.

S & F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long,complete all as specified and as directed.

S&F PVC connection 15 mm dia and 600mm long with two Nos of brass check nuts and washers complete all as specified and as directed.

S & F 15mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

S & F 20mm steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls including taking down old pipe complete all as specified and as directed.

M & L for 1000 Litres rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I and PTMT ball valve 20mm dia including taking down of old tank and removing from site complete all as specified and as directed.

S & F in repair of gun metal gate valve, painted finish, with forged brass spindle and iron wheel head, screwed both ends for iron pipe of size 20mm bore complete all as specified and as directed.

S&F 110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed.

S&F 150 mm PVC (SWR) pipes single socket in any length with rubber ring joints laid in floor or in trenches complete all as specified and as directed.

M&L Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete type D2 (1:4:8) for 150mm dia pipe complete all as specified and as directed.

S&F 110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F 110 mm PVC (SWR) branch piece, (singal T) equal or unequal with access door complete all as specified and ;as directed

S&F PVC (SWR) Floor trap, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good all as directed

M&L for preparation of newly steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M & L for applying 1 mm thick layer of wall putty on walls to give uniform surface, surface scrubbed with emery paper and make surface good and clean complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces

M&L for two or more coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and as directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and as directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and as directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangemen complete all as specified and as directed.

Aluminium Composite Panel (ACP) wall cladding/facade( cut to arch shape or as directed) or in ceiling with sunk or raised moulding/cop design as approved by GE of 6 mm thick HPL sheet, aluminium cover sheet thickness 0.5 mm, panel length 2240 mm and width 1220 mm, interior face coil coated with polyester, fixing with aluminium tube/ aluminium channel with aluminium /steel rivet/screw in any position and height in any colour including preparation of concrete surface for ACP complete all as specified and as directed.

S&F Stainless Steel box type writing letters (Block, Romen, Italic or Indian) of size 300mm hight, 50mm wide and 10mm depth(thick) or size as approved by Engr in charge complete all as directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed.

S&F 125x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc, complete all as specified and as directed.

S&F for steel door including projecting type hinges, steel handles , complete with glazing bars , dovetailed or welded complete all as specified and as directed.

S&F framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe .290.Gde-E-165 complete all as specified and as directed.

S&F rolled mild steel Fe-410w (Gde-E-250) quality 'B' Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power/ LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as directed.Keeping the LED lights in safe custody.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as specified and directed.

Taking down Old/ Unserviceable MCB DBs TPN / Main Switches by disconnection of electric connection including old unsv MCCBs,MCBs, isolators etc and making good to distrubed surface complete all as specified and directed.

Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified and as directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly as specified. Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish. Make:Havells/polycab/Finolex

All as per srl item No 116 but for 3 pin 6 Amps socket outlet independent board including PVC insulated PVC unsheathed 2.5 sq mm earth wire and connected to earth dolly.

All as per srl item No 116 but for 3 pin 6 Amps socket outlet on the same board including PVC insulated PVC unsheathed 2.5 sq mm earth wire and connected to earth dolly.

All as per Srl item No 116 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly.

S&F for modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge. Make: Havells/ Legrand/Indoasian Elvira

S&F for modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge. Make: Havells/ Legrand/Indoasian Elvira

S&F for modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge. Make: Havells/ Legrand/Indoasian Elvira

S&F for modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed by Engr In charge. Make: Havells/ Legrand/Indoasian Elvira

S&F electronic step type fan regulator 100 watt 230 volts 50Hz two module C/S deluxe type complete all as specified and directed.

M &L Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Blockcomplete all as specified and directed by Engr In charge. Make: Havells/ Anchor/Indoasian

S&F single pole and neutral enclosure surface mounted 240 voltswith 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of complete all as specified and directed. Make:- Havells/ legrand/ Indo Asian.

Supply and fixing LED lights fitting 1x 20W, 230V,AC decorative box type warm white colour with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engineer-in-Charge. Make - Havells/ Wipro/Syska

Supply and fixing replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make - Havells / Bajaj//Wipro/Phillips

S&F in replacement 36W (2 x 2) LED Ceiling/recess light panel for recess mounting warm white colour which provides soft-light and glare free symmetrical illumination complete all as specified and directed by Engineer-in-Charge. Make - Havells/ Wipro/Syska

Supply and fixing LED luminaire 12/15/22 watt, 220 V AC recess mounted downlighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp warm white suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge. Make- Havells/ Philips/C&S.

Taking down ceiling fan/Wall fan/Exhaust fans (C/F of any size/make), cleaning its dust particles oiling,greasing,one coat of synthetic enamel white spray painting with blade ,reassemble the same along with all fittings and hanging the same back to its original position including connecting the wire to ceiling rose etc complete after completing the wiring all as specified and as directed by Engr-in-Charge. Note :- (i) The spares like condensor, ball bearing, cotter pin, nuts & bolts, connecting rods & hooks etc if found defective/damage deemed to be replaced and make the ceiling fans functional. No extra payments will be done on this account.

S&F Sheet metal enclosure double door type for MCCB TPN DB upto 125 Amps, 4 way vertical type 415 volts with 400 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Make:- Havells/ legrand/ Indo Asian.

S & F replacement MCCB Three Pole & Neutral capacity of 125 amps 415 volts rupturing capacity 16 KA Make:- Havells/ legrand/ Indo Asian.

S&F Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 08 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.(Note-MCBs will be measured separately) Make:- Havells/ legrand/ Indo Asian.

S & F in replacement MCB single pole 240 volt any rating from 10 to 40 amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable Make:- Havells/ legrand/ Indo Asian.

S & F in replacement MCB single pole and neutral 240 volt any rating from 63 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable Make:- Havells/ legrand/ Indo Asian.

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2X1.5 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 1.00 Sq mm as earth lead all as specified. Including taking down old sub main wire.

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2.5 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 2.5 Sq mm as earth lead all as specified. Including taking down old sub main wire (For street light).

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 4 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead all as specified. Including taking down old sub main wire (for Geyser and AC point).

S&F Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire. Make:Havells/polycab/Finolex

Supply & Fixing Instant Water heating Geyser of capacity 3KW, suitable for 3 ltr instant geysers complete all as specified and directed.

Supply and wall fan , AC single Phase. 230V of size 400 mm sweep with, blades, and frame along with all electrical wire connection all as specified and direceted by Engr-in-charge. Make:Havells/Bajaj/CG

Supply and fix exhaust fan, PVC body AC single Phase. 230V of size 250 mm sweep with, blades, and frame and louvers.

Supply and fixing Smart BLDC ceiling fans complete with accessories,blades, down rods, canopy, shackle assy, and 230 V, AC, 50Hz 1200mm sweep. Min air delivery 210 CFM with service value ≥ 6.00 BEE 5 star rated brushless direct current motor (BLDC) with remote control Complete all as specified and direceted by Engr-in-charge.

Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5 connected to main control board all as specified and testing on completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc.Note: if earth resistance of earthing is not found (2 to 5 Ω) satisfactory if will be redone by the contractor on his risk and cost.

S & F in repairs LED Decorative, STYLO wall mounting, champagne gold finish fixture with plastic body suitable for 9 W LeD lamp B22 base.with driver holder and LED lamp including connecting up with flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing replacement LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Make - Havells / Bajaj//Wipro/Phillips

Hot Press moulded PVC junction box of size 230mm x 170 mm x 105 mm with 200A TPN aluminum Bus bars mouted/ fixed on prorcelain insulator shock and rust proof, cable entry from bottom and other sides, 100% weather proof, with pole/ wall mounting arrangement temper-proof, fire retardant class FV-0 as per IS 11731 Part-II or V-O as per UL-94 including flat iron clamp of size 25mm x 3mm and MCB 10 Amp, complete all as specified and directed. Make:- Sintex/ Naithani plastic works/ Supreme industries.

Supply and fixing post top lantern including GI pipe of suitable size and length LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp fixed on 1:3:6, type C1 (Using 20mm graded crushed stone for plinth size 45*45*45 cm foundation and making electrucal connection with copper cable ) complete all as specified and as directed.

Material & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 4 Sqmm x 2 core size all as specified including taking down old cable.Note : Earth work and other connected work shall be measured & paid sperately.

Material & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size all as specified including taking down old cable.Note : Earth work and other connected work shall be measured & paid sperately.

M & L Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

M&L Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels all as specified and as directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles all as specified and directed.

Supply & fix onload changeover switch(side handle) capacity 63A, four pole, in sheet enclosure, 415V complete all as specified and directed by Engr-in-Charge/GE.

M &L Ceiling rose, surface bakelite 65x 50 mm three terminals fixed on PVC Round Block complete all as specified and directed by Engr In charge. Make: Havells/ Legrand/Indoasian Elvira

S&F sub main wiring with two single core FRLSH PVC insulated unsheathed multistranded copper conductor of size 6 Sqmm nominal cross sectional area and one run of 6 sqmm nominal cross sectional area FRLSH PVC insulated unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25 mm dia 'medium grade' PVC concealed conduits and fittings, complete all as specified and directed. NOTE: One unit length shall measured as two run of main wire and one run of conduit & earth wire Make: Havells / Finolex / Polycab.

Supply and fixing LED lights fitting 1x 20W, 230V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed Make- Havells LED Pride Plus Triyca Batten 20 W 6500 K CAT Part No LHEXAXPNIN1W020/ Bajaj BLTRU 20W NW VIVA cat part No 112177/ Philips StarBright Wide 20W

Supply and fixing LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. Make- Philips/Crompton/Havells

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers along with all electrical wire connection all as specified and direceted by Engr-in-charge. Make- Havells/CG/Bajaj

Material & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 16 Sqmm x 4 core size all as specified including taking down old cable

S&F Double Walled corrugated DWC Pipe of size 40 mm including snap fit coupler Pt-II for protection of LT Cable in underground all as specified and as directed.