SPECIAL REPAIR TO BLDG NO S AND T - 46 OF 304 (I) SUP PL ASC AND PROVN OF WALL PANELLING, FALSE CEILING, TILES AND SANITARY FITTINGS IN BLDG NO MH - 14 AND MH - 22 AT JUTOGH CANTT UNDER GE JUTOGH

Amount

Demolition of cement concrete un-reinforced in ground floors and pavings n exc 15 cm thickness (below or above ground level, complete all as specified and directed.

M&L 75mm thick PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate as in sub base complete all as specified and directed.

M&L 25mm thick PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in sub base of floor finished concrete surfaces even and smooth without using extra cement, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, type C-2, using 40mm graded crushed stone aggregate as in plinth protection, path, hardstanding, finished concrete surfaces even and smooth without using extra cement, complete all as specified and directed.

Removing unserviceable building material obtained from dismantling/demolition to a distance exc 1.0KM but n.exc 1.50KM and depositing where directed at level not exc 1.5m above the starting point complete all as specified and directed.

Demolition of brick or stone masonary built in cement mortar including all quoins arches pillars etc but excluding ashlars facing dressed stone work and precast concrete block, complete all as specified and directed.

M&L for brick work with sub class 'B' brick, straight or curved on plan exc 6m mean radius, built in CM 1:6, complete all as specified and directed.

M&L for brickwork with sub-class 'B' bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with eater etc, of any height including necessary scaffolding and T&P required to complete the work complete all as specified and directed.

M&L for rendering 15 mm thick on fair surfaces of brickwork or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement at any height complete all as specified and directed.

M & L for rendering 15mm thick on other than fair faces of brick work or concrete surface in CM 1:4 surface finished fair and even mixed with water proofing compound as per manufacturers instruction, at any height complete all as specified and directed. Note: WPC shall be measured and paid separately.

M&L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion including priming coat over a coat of 2-3mm thick wall care putty on plastered surface complete all as specified and direceted.

M&L for prepartion of newly plastered surface of wall applying two coats of weather proof anti fungal exterier emulsion paint on external surfaces including a coat of alkali resistant priming paint complete all as specified and direceted.

M&L for complete removal of existing treatment on wall (any number of layers) by scrapping with steel scrappers or any other means, over and incl 2-3mm thick wall care putty and applying two coats of oil bound distemper of approved shade complete all as specified and as directed .

M&L for complete removal of existing treatment from walls and applying two coats of weather proof anti fungal exterier emulsion paint on external surfaces including a coat of alkali resistant priming paint at any height of building / tower complete all as specified and directed.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and incl 15mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, fixed over and including 10mm thick rendering in CM 1:4 on vertical surface such as skirting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match the surface complete all as specified.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed with cement mortar 1:6 complete all as specified and directed.

M & L for granite (of any type) 18-20 mm thick one side machine polished in steps, jambs, pillars, window cills and top of kitchen platform and counter top of wash basin etc set and jointed in neat cement slurry and pointed with coloured cement to match fixed over and including 20mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for granite (of any type) work 18-20mm thick (table rubbed and polished) for wall lining (veneering to wall) including laid over 15mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite fixed over and including 10mm thick backing coat in cement mortar 1:4 complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in , cooking platform, and other similar situations complete all as specified and directed.

Demolition of reinforced cement concrete as in cooking platform, lintels, chhajja, cover slab etc of any description and in any position not other wise specifically provided for complete all as specified and directed.

M&L for RCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate as slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like compete all as specified and directed.

M&L for PCC 1:2:4, type B-1, using 20mm graded crushed stone aggregate, as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking , bending, hooking end and binding with and including mild steel wire not less than 0.9 mm dia and securing with clips complete all as specified and directed.

M&L MS TMT bars, 5mm dia and over upto and incl 10mm dia as in stirrups, spacers, binders etc cut to shape requred, incl cranking spirally for hooping for columns, hooking ends binding with and including mild steel wire not less than 0.9mm dia complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards any thickness, any description including cover fillets compete all as specified and directed.

M & L for 4mm thick non asbestos fibre cement building boards (E board designer with PVC white coating) fixed or laid /inserted to timber/GI/Aluminium frame work with screws in ceiling flat or sloping compete all as specified and directed.

M&L for GI frame work of size 605 x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx. 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre compete all as specified and directed.

S&F hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long compete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for truss/purlin/rafter compete all as specified and directed.

M&L for MS Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc of Fe-410-W (Gde-E-250) quality B, compete all as specified and directed.

Errection and fixing only MS Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, compete all as specified and directed. Note: Steel obtained from dismantling shall be reused.

M&L for preparing old painted steel & iron surfaces of any description over 10 cm in width or girth ,including roof and applying one coat of white/ approved colour/ shade of synthetic enamel paint complete all as specified and directed

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces of any description over 10cm wide or girth incl preparation of surface etc., compete all as specified and directed.

Dismantling plain or corrugated steel sheeting any gauge, thickness, including nainital or similar pattern in roof covering, compete all as specified and directed.

M&L for pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws compete all as specified and directed.

M&L for pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall eaves board etc., fixed with self tapping screws compete all as specified and directed.

Taking down chowkhats or frames n exc. 1.5 sq. m each with shutter (without taking off shutters from the frames) and removing from site compete all as specified and directed.

Taking down chowkhats or frames exc. 1.5 sq. m but n.exc 4 sqm each with shutter (without taking off shutters from the frames) and removing from site compete all as specified and directed.

M&L for IInd class hard wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F framed work such as grills, gratings, etc.,with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladder; framed baluster; walk ways; railing; framework of watertanks staging and similar work conforming to Fe-410. Gde-E-310 compete all as specified and directed.

S&F steel windows with side hung shutters including box type hinges with MS handles, MS peg stay with glazing bars, complete all as specified and directed.

S&F steel windows with side hung shutters including box type hinges with MS handles, MS peg stay without glazing bars, complete all as specified and directed.

S&F steel ventilator with top hung shutters with steel handle, and steel peg stay, complete all as specified and directed.

S & F MS band straps, clamps, hold fasts, wind ties, fillets etc and similar small articles confirming to Fe 410 Gde E-310 complete all as specified and directed.

S&F flush shutters, 35 mm thick, solid core construction, with block board core and plywood face panels, commercial type on both side with lipping/frame to match compete all as specified and directed.

S&F 2nd class hardwood Glazed and skeleton shutter 35 mm thick, open rebated and prepared to receive glass, gauge etc, (without shas bar), edges of framing plain or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 clause 8.20(a) supplied and fitted to chowkat etc compete all as specified and directed.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staple including wooden beading complete all as specified and directed.

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty or wooded bead built in squares not exceeding 0.5 sq.m in each pane, compete all as specified and directed.

S&F sheet glass 4mm thick Figured glass, pin head type and glazing with oil putty or wooden bead in squares n exc 0.5 sq. m in each, compete all as specified and directed.

M&L for preparing new or previously untreated surfaces of wood and wood based materials of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Factory made panel PVC door shutter 30 mm thick (style) consisting of frame made out of M S tubes for top & bottom rails M S frame shall be covered with heat moulded plain colour PVC ‘c’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour pick sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bottom rail, Paneling of colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable pick sheet beading and jointed together with solvent cement compete all as specified and directed.

S&F Solid PVC door frame of size 50mm x47mm made out of 5mm thick plain coloured PVC sheet reinforced with M.S. Square tube, compete all as specified and directed.

S & F mild steel 300mm ordinary rat rail pattern springs including roller and roller plate compete all as specified and directed.

S&F aluminium handles, fabricated type, anodised 150 mm size compete all as specified and directed.

S&F butt hinges 100 mm size medium weight cold rolled mild steel compete all as specified and directed.

S&F butt hinges 75 mm size medium weight cold rolled mild steel compete all as specified and directed.

S&F butt hinges 50 mm size medium weight cold rolled mild steel compete all as specified and directed.

S&F 200 mm aluminium anodised barrel tower bolt of extruded section and fixed, compete all as specified and directed.

S&F 250 mm long aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

M&L for 2nd class hard wood small fittings such as brackets of any type, latch & hinge blocks, shaped door & window stops & the like including all necessary labours, articles n exc 200 cucm each compete all as specified and directed.

M&L for 20 mm dia mild steel coloured PVC coated fancy curtain rod fitted in MS coloured bracket complete all as specified and directed.

M&L for mild steel coloured brackets including PVC designer dom for curtain rod complete all as specified and directed.

S & F Solid PVC Wall / ceiling Lining consisting of 5mm thick single side prelam wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame complete all as specified and directed.

M&L for IInd class soft wood plain fillets exc 13 & n.exc 25 sqcm rectangular in section ,clean sawn ,secured with nails or brads for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing to wall/ ceiling paneling complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint (weather proof paint on external surfaces) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces at any height of building / tower complete all as specified and directed.

S & F 15mm bore galvanised steel water tubes medium grade with all fittings and fixed to walls and ceilings or laid in floor of size complete all as specified and directed.

M&L for cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth compete all as specified and directed.

S&F in repair PVC valve less, syphonic action type low level flushing cistern, white with inlet ball valve , float handle , including brackets 10 ltr capacity including 32 mm PVC flush pipe complete all as specified and directed.

S&F in repair Wash hand basin, flat back 630x450mm vitreous china (white) including CP waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing complete all as specified and directed.

S & F in repair vitreous China wash down (EWC) water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) but including plastic water closet seat cover closed pattern with flat bottom and cover with PVC hing devise, fixing bolt for pedestal pattern and cast iron 'P' or 'S' trap complete all as specfied and directed.

S&F in repair 15mm dia stop valves, cast copper alloy, screwed down, high pressure, with crutch or butter fly handle, fancy type, chromium plated, screwed both ends for iron pipe or unions compete all as specified and directed.

S&F in repair 15 mm bib tap fancy type cast copper alloy chromium plated long body with crutch with butter fly handle, screwed for iron pipe or brass ferrule, compete all as specified and directed.

S & F in repair 15mm dia chromium plated brass central hole wash basin mixer (pillar tap) with accessories in wash basins for mixing hot and cold water, screwed down for 15 mm bore GI pipe complete all as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600mm long compete all as specified and directed.

S & F in repair 15mm dia brass CP wall mixer for mixing hot & cold water with hand shower, screwed down for iron pipe compete all as specified and directed.

S&F in repairs glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, compete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality along with EPDM rubber all around the glass edges exc 0.5 sqm in each pane and fixed into aluminum frame work, compete all as specified and directed.

S&F 12 mm thick pre laminated particle board, interior grade, pre laminated both sides with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminum/timber frame work complete all as specified and directed.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium door, window, ventilator frame with side hung /including bombay sliding aluminium sections sliding window where required or pull and push type in frames and shutters with two track sliding aluminium frame and in partitions , including necessary joining cleats, glazing clips, anodised aluminium snap beading, screws, including necessary anodised aluminium fittings like handles etc compete all as specified and directed.

S&F EPDM rubber beading around glass in aluminium windows/ ventilator shutters compete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. compete all as specified and directed.

M&L for Vitrified Ceramic tiles 8-9 mm thick (square/ rectangular) polished light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over a screed layer of 15mm thick in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350x250x7mm thick/450x350x7 mm thick fixed over and including 10mm thick screed bed in CM 1:4 on vertical surface such as skirting/dado set and jointed in neat cement slurry and pointed in white cement mixed with colour pigment to match the existing surface complete all as specified.

M/S Meera Builders

M/S JOHN VASSELLY

M/S Jaswant Kumar Aggarwal