Renovation of CSIO Staff quarters A block (A-1to A-9 and A-11) all under CSPS scheme

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas,lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement: 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting, propping etc. and removal of form Shelves (Cast in situ)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade more. Fe-500D or more

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 12.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement: 4 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick granite gang saw cut, mirror polished, premoulded and prepolished, machine cut for Stiar case/kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. colour black /cherry /ruby red or as approved by EC Area of slab over 0.50 sqm Basic rates 250 per SQFT

Providing and fixing Min 15mm thick full body granite/tile for kitchen counter kajaria vitronite /equivalent ,kitchen latforms, vanity counters, ls, and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand)/ Adhesive (Roffe) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. with gas pipe line hole wherever reqiured complete at all levels. Area of slab over 0.50 sqm.( basic rate must be Rs 300 per sqft) any colour and sample as approved by Ein C

Providing edge moulding to 18 mm thick Granite, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work.

Providing and fixing double edge moulding to kitchen counter etc., including machine polishing to edge to give high gloss finish etc.complete as per design approved by Engineer-in-Charge.Kajaria full body granite Vitronite

Providing and fixing 1st quality ceramic glazed wall tiles 30 X45 cm size digital series with highlighter conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. make Kajaria digital hi-definition ceramic wall tiles series or equivalent make

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (with hold fast /deshfastener ) .Kiln seasoned and chemically treated hollock wood including dismantling existing frame work.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Ply wood 7 ply, 9 mm thick Decorative plywood one side decorative veneer and commercial veneer on other face (Type 1) conforming to IS 1328 BWR Type

P/ F glazed window door ,Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws. Kiln seasoned and chemically treated hollock wood 35 mm thick

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISi marked Stainless Steel butt hinges with necessary screws Greenply or equivalent make.Lamination 1mm of Virgo ,greenlam etc

Extra for rebate for flush door shutter, Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISi marked flush door shutters conforming to IS: 2202 (Part I) On one side only

Providing and fixing double wire gauge shutters using stainless steel wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :30 mm thick shutters with ISi marked M.S. pressed butt hinges bright finished of required size Kiln seasoned and chemically treated hollock wood

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and fixing stainless steel hasp and staple (safety type) with necessary screws etc. 150mm. Including dismantling existing if any.Godrej/Hetich

Providing and fixing Staineless Steel sliding door bolts, ISI marked anodised transparent or dyed to required colour or shade, with nuts and screws etc. complete 250x16 mm Godrej

Providing and fixing Staineless Steel tower bolts, ISi marked, anodised transparent or dyed to required colour or shade, with necessary screws etc. complete200x10 mm Godrej

Providing and fixing Stainless Steel tower bolts, ISi marked, transparent or dyed to required colour or shade, with necessary screws etc. complete 150x10 mm Godrej /Ebco

Providing and fixing Staineless Steel handles, ISi marked, anodised transparent or dyed to required colour or shade, with necessary screws etc. complete 125mm

Providing & fixing factory made Cup board /Almirah having box type overhead units after dismantling of existing wood work and frame ,brick of existing almirah . The frame work or carcass of the cabinets including facia/sides /bottom, shelves etc. shall be made out of 18 mm thick HDHMR board with bothside balancing lamination(0.8 MM thick ) of century/green ply panel .The almirah must have with provision for hanging cloths box ,storage of small item drawers ,open niches boxes etc box should made with HDHMR 18mm thick HDHMR board with bothside balancing lamination 0.8 mm , all front edge should be cover with 2 mm edgebending tape (rehau make) all necessary fittings. Shutter should be make on HDHMR board 18 mm thick with 1 mm thick MICA high gloss lamination front side and balancing laminated on back side. All edge should be covered with high gloss edge bending tape. Tape should be fixed with hot melt glue and fix with pressed machine & all the edges to be sealed .Each shutter shall be fixed to the framework by SS hinges. Cabinet to be fixed in complete as per the direction of the Engineer-in-Charge. Details Drawings shall be submitted by the contractor and before execution got approved by the Engineerin-Charge, before execution of work). Only Face area of shutter shall be measured for payment purpose The item including dismentling existing cup board with wooden frame and shift with in CSIO stores. The Almirah to be made as per drawing of pre- approvel by engineer in charge as prepared by contractor All fittings to be of Heffle,Hettich,Godrej

Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. Up to 200mm long godrej /hettich

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make up to 600 mm long with screws etc. complete as per direction of Engineer- in-charge. hettick/hafele / innotech or equivalent make

Structural steel work riveted, bolted or welded in built up sections, square, tube , angle , trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat.

Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with 4.0 mm thick glass panes

Providing and laying double charge Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polimer modified quick set tile adhsive water based. conforming to IS 15477 average 10mm / chemical and jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments, etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily .Double charge vitrified tile polished finish of size. Size of Tile 600 x 600 mm or more. Make kajaria Double charge/classic sonics polished vitrified tiles

Providing and laying double charge Vitrified tiles in different sizes ( min 600 x600 or more ,thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, with the approved tile adhesive Roff /MYK laticreteg grouting the joint with white cement & dismentling exiting skerting terazzo or chips plaster/ tiles.The grouting with matching pigments etc. complete.Size of Tile 600x600 mm.Make kajaria Double charge/classic sonics polished vitrified tilesSample to got approved from E in C

Providing gola 75x75 mm, Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement: 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter Make prince/supreme

12 mm cement plaster of mix : 1:4 (1 cement : 4 Fine Sand)

15 mm cement plaster on rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand)

20 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture of Asian/Nerolac/Dulux paint

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats. Make :- Asian/Nerolac/Dulux paint

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer of Jk wall putty/Asian/Birlawallcare putty, over the plastered wall surface to prepare the surface even and smooth complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work Make :- Asian/Nerolac/Dulux paint or

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : two coats on old work Asian/Nerolac/Dulux paint or

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) Make :- Asian/Nerolac/Dulux paint

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface Make :- Asian/Nerolac/Dulux paint

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : With cement mortar 1:4 (1 cement : 4 fine sand)

Demolishing cement concrete manually/ by mechanical means including disposal of material within CSIO as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within CSIO as per direction of Engineer - in- charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within CSIO as per direction of Engineer-in-charge.In cement mortar

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO : Of area 3 sq. metres and below

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within CSIO Of area beyond 3 sq. metres

Dismantling the stone slab/Tile work/Brick tile terracing roof/terrazzo tiles in floors & roof laid in cement mortar including stacking of materiall and disposal of unserviceable material within CSIO. For thickness of Stone slab/Tile upto 40 mm.

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means including stacking of pipes within CSIO as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore

Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually/ by mechanical means breaking lead caulked joints, melting of lead and making into blocks including stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-charge: Up to 150 mm diameter

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within CSIO.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within CSIO.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 17.1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. Make :- Cera/Hindware

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. Make :- Cera/Hindware

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- Charge. Make Cera or equivalent

Providing and fixing P.V.C. waste pipe for sink or wash basin including Flexible pipe 32 mm dia P.V.C. waste fittings complete. points of approved quality conforming to IS:8931 15mm nominal bore Make :- Viking or equivalent

Providing and fixing 100 mm sand cast Iron grating for gully trap.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : C.P. brass Make Cera or euqivalent

Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729 Make :- NIF/RIF/BIC or equivalent

Providing and fixing soil, waste and vent pipes : 75 mm dia Sand cast iron S&S pipe as per IS: 1729 Make :- NIF/RIF/BIC or equivalent

Providing and fixing plain bend of required degree. 100 mm dia Make :- NIF/RIF/BIC or equivalent

Providing and fixing plain bend of required degree. Make :- NIF/RIF/BIC or equivalent 75 mm dia

Providing and fixing single equal plain junction of required degree : 100x100x100 mm Sand cast iron S&S as per IS - 1729 Make :- NIF/RIF/BIC or equivalent

Providing and fixing single equal plain junction of required degree : 75x75x75 mm Sand cast iron S&S as per IS - 1729 Make :- NIF/RIF/BIC or equivalent

Providing and fixing collar : 100 mm Sand cast iron S&S as per IS - 1729 Make :- NIF/RIF/BIC or equivalent

Providing and fixing collar : 75 mm Sand cast iron S&S as per IS - 1729 Make :- NIF/RIF/BIC or equivalent

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 100 mm

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 75 mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet: Sand Cast Iron S&S as per IS: 1729 Make RIF/Adhunik/NECO/BC

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 75 mm outlet: Sand Cast Iron S&S as per IS: 1729 Make RIF/Adhunik/NECO/BC

Providing and fixing CP towel ring with concealed fittings arrangement of approved quality. Make Cera or equivalent

Providing and fixing floor mounted, white vitreous china single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous china cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover,Hand Jet CP cistern fittings, nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in-Charge. Make :- Cera/Hindware

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :15 mm dia nominal bore. Make TATA/ Jindal (Hissar) or Equivalent

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :20 mm dia nominal bore TATA/ Jindal (Hissar) or Equivalent

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore 15 mm nominal bore. Make Cera or equivalent

Providing and fixing brass stop cock of approved quality 15 mm nominal bore. Make Zoloto or equivalent

Providing and fixing brass stop cock of approved quality 20 mm nominal bore. Make Zoloto or equivalent

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore. Make Viking or equivalent

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter. Make cera or equivalent

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 15 mm nominal bore . Make SVW/UNIK/UF

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 20 mm nominal bore Make SVW/UNIK/UF

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore. Make Cera or equivalent

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing CP grating of approved quality and colour. Circular type 100 mm nominal dia Make Chilly or equivalent

Providing and fixing CP soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.Make Cera or equivalent

Providing and fixing soil, waste and vent pipes : 100 mm dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989. Make BIC/HIF/NECO

Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : 100 mm dia pipe

Providing and fixing plain bend of required degree. 100 mm dia Sand cast iron S&S as per IS : 3989 Make BIC/HIF/NECO

Providing and fixing heel rest sanitary bend 100 mm dia Sand cast iron S&S as per IS - 3989 Make BIC/HIF/NECO

Providing and fixing single equal plain junction of required degree : 100x100x100 mm Sand cast iron S&S as per IS - 3989 Make BIC/HIF/NECO

Providing and fixing collar : 100 mm Sand cast iron S&S as per IS - 3989 Make BIC/HIF/NECO

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay F.P.S. (non modular) bricks

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 . Make RIF/Adhunik/NECO/BC

Waterproofing :- Premix Compound Components A and B using an electric double-paddle mixer for 2–3 minutes at low speed. Apply the first coat of Compound at a rate of 0.80–0.90 kg/m² without dilution, using a lamb’s wool or cloth roller. While the coating is still wet, roll and embed a 225 gsm Fiberglass Chopped Strand Mat, ensuring full bonding without air bubbles or wrinkles. Allow the first coat to dry for 3–4 hours. Apply the second coat at a 90° angle to the first. Overlap the chopped strand mat by at least 5 cm at the joints, ensuring the overlaps are sufficiently wet to achieve proper bonding. Once the surface is dry enough to walk on, apply the second coat at 0.80 kg/m². Apply additional coats as needed to achieve a total dry film thickness of 900–1000 microns, with a total system material consumption of 1.60 kg/m² over 2–3 undiluted coats. Note – Coating should be terminated below the drip mould on the vertical surface. The material has followed technical properties: Attains a Tensile Strength ≥ 18 N/mm2 as per ASTM D 2370; Crack bridging ability, Tear Strength ≥ 160 N/mm as per ASTM D 624, Dynamic Crack bridging as per EN 13251:2016 - No Cracks after 20000 sinusoidal cycles, Dynamic Crack bridging as per ASTM C 1305-2016 - Pass, No Crack, Pass Low Temperature Flexibility (-20 after 1000 Hrs. UV as per ASTM D 1970-2021, Shore A as per ASTM D2240 – 85 , Peel Adhesion to Concrete under wet Condition -24 Hrs. – N As per ASTM C 794 – 11.4 , Abrasion resistance (CS 17 Wheel -1000 Cycle, 1.0 Kg) as per ASTM D 4060 - 7 mg , Depth of Water Permeability @ 10 Bar as per EN 12390-8-2019 – Nil Water Migratlon Resistance as per ASTM D 7281,-2007 - No Leakage, Pass Spread of flame Class makes BASF, Pidilite, Fosroc, MAPEI, CIPY . The Operation shall be carried out after scrapping and properly cleaning the surface to remove loose particle with wire brushes complete in all respect as per direction of engineer in charge.All the agencies should be having valid trained/authorized applicator certificate certified by the agency i.e. BASF, Pidilite wonderproof , Fosroc, MAPEI, CIPY please read general instruction also an Gurantee 10 years to be furnished and MOU with manufacture to be signed .

Re-grading terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 (1 cement : 3 fine sand), including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground (the cost of the new tiles or brick excluded), all complete as per direction of Engineer-in-Charge.

Raking out joints in lime or cement mortar on Roof /wall and preparing the surface for re-pointing or replastering, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.

Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement on flat tile bricks on top of mud phaska roof : With F.P.S. brick tiles

Removing & laying Flush pointing with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight on vertical Brick wall exposed surface

Taking out the door shutter & refixing the same after making necessary adjustment/Modification with hinges and nails beading as per direction of Engineer in Charge.

Providing and fixing factory made box type kitchen INNOTECH/TENDUM cabinat under kitchen counter ,cupboard /storage units made up of 18mm HDHMR board(century/ Green panel/Action tesa). The shutters shall be fixed with consealed soft close Hinges , gola handle of approved design & front edges to be covered with PVC edge beading tape (2.0 mm thick) (Rehau,Century, Green lam, Merino or approved equivalent make). The shutters should be make with HDHMR board with 1.5 mm thick acrylic high gloss finish make (Alimo or equilant) side on back side with machine pressed and alledges should be covered with bend tape 1.33mm thick high gloss PVC edge . The tape should be fixed with hot melt glue and through the machine heavy PVC leg or Adjuster should be used bending tape. Cabinet to be fixed in proper place/such as under counter of kitchen or over heads above the counter with required dash fasteners & The carcass of the cabinet including drawer shall INNOTECH be made of 19 mm thick HDHMR with acrylic lamination 1mm each shutter should be fixed to frame work using tw godrej/hettich Hafele 45 kg or equivalent make. In each kitchen there shall be tandum for for storage , cutlery , cup saucer, for thali, pull out as per drawing. The over head kitchen to be made with HDHMR with acrylic and shutter v type for storage complete in all respect as per the direction of Engineer- in-charge.The rate include cutting for kitchen counter for fixing existing SINK .(Details Drawings shall be submitted by the contractor and got approved from the Engineerin-Charge, before execution of work). Only FACE AREA of shutter shall be measured for payment purpose for overhead and under counter modular kitchens inclusive of all fittings etc the contractor touse e all good quality godrej/hettich/Haffle items if required will be paid in seprate item ) Only tentative concept drawings enclosed for rate. this including dismentling existing cup board with wooden frame and shift with in CSIO

Removing and refixing of all plumbing item in bathroom and toilet after the wall tiles and floor fixing in proper size with extension nipple or CP tap.

Providing and fixing 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Make Cera or equivalent

Providing and fixing 15 mm dia CP Brass single hole wall mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Make Cera or equivalent

Finishing walls/Roof with Damp Proof Paint with additives of required shade (Two coats ). including priming coat of one coat of primer applied Make :- Asian Damp Proof paint or Equivalent. The Operation shall be carried out after scrapping and properly cleaning the surface to remove loose particle with wire brushes complete in all respect as per direction of engineer in charge

Providing and fixing S.S. Wire mesh and aluminium mesh with beading to door and clerestory windows using wire gauge with With second class teak wood beading.

Providing and fixing ply board 12 mm commercial ply of approved make, including with necessary screws and complete as per direction of Engineer-in-Charge.

Providing and fixing 3 mm thick translucent white acrylic plastic sheet on duct covering etc complete as per architectural drawings and directions of engineerin- charge.

Carrying out petty jobs of carpentary including of doors, Almirah, pelmets, storage spaces etc. complete with necessary tools, drill machine nails, screws ,fevicol, SR etc. at diffrent locations which can not be measured as directed by engineer in charge.

Carrying out petty jobs of massonary work including of alltypes of repairs with coc. And mortar etc. complete with necessary tools, cement, sand, aggregate etc.at diffrent locations which can not be measured as directed by engineer in charge.

Carrying out petty jobs of misc.petty works with all necessary tools,Rehri,etc.at diffrent locations which can not be measured as directed by engineer in charge.

Carrying out petty jobs of Plumbing works with all necessary tools like pipe wrench , drilling machine drill bits, safety , old cycle tubes etc for petty works at different locations which can not be measured as per direction by engineer in charge.

Tank Shifting on roof & Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 15 to 20 mm nominal bore

Providing and fixing aluminium sheet 22 gauge thick over the door with nail and other necessary

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610X460mm bowll depth 200 mm. Make Neelkanth /Nirali or equivalent

Providing and fixing fly proof S.S wire gauge to windows and clerestory windows using wire gauge with With second class teak wood beading.

Providing layer of , reinforced with galvanisied steel wire fabric (25x 25 mm or 25X50 mm oe equivalent ) size of 10guage thick ) forming a vertical plate bonded to wall . Two plate on either side of wall shoul be connected by galvanized steel rods at spacing of about 300 to 400mm .

Supplying and spraying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos / Lindane along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. with Chlorpyriphos / Lindane E.C. 20% with 1% concentration of treatment at points of contact of wood work by chemical emulsion Chlorpyriphos / Lindane in oil or kerosene based solution @ 0.5 litres per hole by drilling 6 mm dia holes at downward angle of 45 degree at 150 mm centre to centre and sealing the same.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. i) Group B

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.

Wiring for circuit/ submain wiring alongwith earth wire with 2X4 sq mm + 1X4 sq mm earth wire PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.

Wiring for circuit/ submain wiring alongwith earth wire with 2X6 sq mm + 1X6 sq mm earth wire PVC insulated copper conductor, single core cable in surface/ recessed PVC conduit as required.

Supplying and drawing of 3 x 1.5 sq. mm FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 5/6 A modular switch on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin 5/6 A modular socket outlet on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and Fixing brass batten/ angle holder including connections etc. as required.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Brush Less Direct Current (BLDC) Fan with Remote :- Supply, Installation, Testing and Commissioning of ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, steel/Al body. Power Factor not less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM (tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than 10%, remote (preferably mobile app based) for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS 374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required. 1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min (Minimum)

Supplying and fixing 6 way , Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) .

Supplying and fixing 8 way , Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing 12 way , Double door , Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing Cable End Box (Loose Wire Box) suitable for For 14 way, Double door SPN MCBDB single pole and neutral, sheet steel, MCB distribution board, 240 Volts, on surface/ recess, complete with testing and commissioning etc. as required.

Supplying and fixing 63A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Triple pole and neutral in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63 A, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of Single Pole in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 25mm size of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating along with all ancillaries and accessories like coupler etc. as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Making the opening of suitable size in the Brick wall/window for installation of Exhaust Fan of Size 300mm sweep, including making good the damage, complete as required at site.

Supply of Metallic Body Exhaust Fan of size 300 mm sweep, with G.I. sheet louver shutter, Grey in color, RPM: 900-950, four number blades, Air delivery (minimum) 1145 m3/h, low noise level, suitable for 230V, 50 Hz, single phase AC Supply, complete as required.

Installation of exhaust fan of size upto 450 mm sweep in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

LED Batten light (System lumen efficacy ≥105 <120lm/Watt). 18-22 Watt:- LED Batten light 18-22 watt (System lumen efficacy ≥105 85%, Operating voltage AC 140 270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder Coated CRCA Sheet Body (Thickness > 0.50 mm)

Supply of LED Batten of rating 5W cool day light, minimum lengh 270mm, suitable for 230V, 50 Hz, single phase AC Supply, complete as required.

Supply of wall mounted fancy light fitting suitable for 1-Phase, 230V, 50Hz for home décor complete with LED lamp 3watt to 9 watt as required at site . Make: Good quality as approved by the Engineer-in-charge.

Installation ,Testing, Commissioning of wall bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required.

Supplying and fixing 12W LED Bulk Head Light fitting, IP65, including connections etc. as required.

LED Street light fixture, powder coated pressure die cast aluminium body (System lumen efficacy ≥105 <120 lm/Watt), 30 Watt along with suitable size G.I. pipe (light class) bracket : - Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminium body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 48 DELHI SCHEDULE OF RATES (E&M)-2025 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70,under voltage and over voltage protection, EMI EMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),SDCM (Standard Deviation Colour Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output .LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). It also includes suitable size G.I. pipe (light class) bracket for mounting of led fitting on wall including bending of the pipe to required shape, 2 nos. G.I. flat iron clamps with nut, bolts, and washer etc.

Supplying and fixing of phenolic laminated sheet of 3 mm thick , ISI marked with cutting etc. anyone of make Heylem/Super Heylem.

Labour Charges for Disconnection and Dismantling of old electrical acessories from staff quarter and shifting of material from site to store as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supply of 4 core 16 sq.mm 1.1KV grade, one number XLPE insulated, aluminium conductor, armoured power cable confirming to latest IS standards.

Supply of 3.5 core 95 sq.mm 1.1KV grade, one number XLPE insulated, aluminium conductor, armoured power cable confirming to latest IS standards.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Upto 35 sq. mm direct in ground including excavation, sand cushioning protective covering and refilling the trenchetc. as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size Upto 35 sq. mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning protective covering and refilling the trenchetc. as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size above 35 sq. mm and upto 95 Sq.mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning protective covering and refilling the trenchetc. as required.

Supplying and making end termination with brass compression gland and aluminium lugs of size 4 X 16 sq. mm (28mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and making end termination with brass compression gland and aluminium lugs of size 3.5 X 95 sq. mm (45mm) of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

Sypply, installation, testing & commissioning of cubical type,outdoor type, single door, Floor mounted, fixed type, free standing single front, dust proof Outdoor Aluminium Bus Bar Feeder Pillar made out of M.S. CRC Sheet 14G, Base Frame Angle 40X40X5mm duly red Oxide Primer with PO Red Paint as per specification. Approximate Size (H) 1200mm X (W) 900mm X (D) 450mm X (L) 600 mm long legs. Bus Bar size 400A TPN Aluminium Busbar (Horizontal) & Earth strip throughout the length of Panel Busbar supports shall be DMC epoxy Insulators. All Busbars Links shall be covered/ insulated with Heat Shrinkable sleeves of coloured coded Red, Yellow, Blue & Black. Aluminium solid interconnection Busbar to to field side for Cable termination duly covered/ insulated with Heat Shrinkable sleeves of coloured coded Red, Yellow, Blue & Black. All Interconnections of fields side are supported by conical, L & Finger type insulators of adequate size to support & sustain the weight of cables & without Power Wiring. Panel should be complete with all accessories like Gasket, Doorlocks, earthing stud etc. and should be as per Technical specification of CPRI guidelines. Panel should be fabricated from the approved panel fabricator.

Please Enable Macros to View BoQ information