ADDL/ALTERATION TO BLDG NO. J-1, J-3, J-6 AND J-7 (16 QTRS BLOCK) JCOs MD ACCN AT RR COLONY DELHI CANTT

Amount

Item No. 1 Dismantling of water tank of any type/pattern exc 250 ltr but n exc 500 ltr capacity and removing from site complete all as specified and directed.

Item No. 2 Demolition of cement concrete (Un reinforced) in ground floors n.exc 15cm thick (above or below grnd level) including removal of rubbish from site complete all as specified and directed.

Item No. 3 Demolition of cement concrete ( Un-reinforced) in Ground floors and paving exc 15cm thickness (below or above ground level) including removal of rubbish out side complex (Defence land), complete all as specified and directed,

Item No. 4 Taking down cement plaster of any description on brick, stone or concrete walls surfaces including raking out joints hacking for keys scrubing down with water etc complete all as specified and directed.

Item No. 5 Dismantling boarding any discription fixed in any position with nails or hinges complete all as specified and directed..

Item No. 6 Taking down chowkhat or frame not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Item No. 7 Taking down chowkhat or frame exceeding 1.5 Sqm each and not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) complete all as specified and directed.

Item No. 8 Taking down shutter of any description area exc 1.00 sqm and n exc 2.00 sqm each.complete all as specified and directed.

Item No. 9 Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Item No. 10 Demolition of stone slab and tiles of any description or thickness in floor apron etc laid bedded and pointed in any mortar complete all as specified and directed.

Item No. 11 Demolition of reinforced cement concrete (re-inforcement cut as required to facilitate demolition) such as chajja,manhole cover parapet wall ,lintel up to 4.5 m span including hieght upto four storey building , in any position complete all as specified and directed.

Item No. 12 M&L sand filling under floors or in foundations including watering and consolidation complete all as specified and directed..

Item No. 13 M&L for precast factory made manhole/gully trap cover of size 450x450 mm, 50 mm thick with SFRC concreting including grove and hook arrangement for lifting and placing in position and sides covered by MS sheet complete all as specified and directed

Item No. 14 Taking up or down steel tubing and connections, bore of tubing 15mm complete all as specified and directed.

Item No. 15 Taking up or down steel tubing and connections, bore of tubing 20mm complete all as specified and directed.

Item No. 16 Demolition of brick work built in cement or cement lime mortar of any description including quoins, arches, pillars, etc., complete all as specified and directed.

Item No. 17 S&F rotational moulded polyethylene water storage HDPE tank of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and directed including 20 mm size ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms). Note:- overflow pipe of each tank shall be connected to nearest rain water outlet and shall be measured and paid under respective item.

Item No. 18 M&L for cement concrete 75mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) finished even and fair in paths laid in alternative panel.complete all as specified and directed.

Item No. 19 M&L cement concrete 1:4:8 type D2 (using 40mm graded crushed stone aggregate) as in foundation filling and mass concrete , complete all as specified and directed.

Item No. 20 S&F in repairs kitchen plate rack with four shelves made out of stainless steel sheet 1mm thick of AISI-306 over all size 90x80x25cm complete all as specified and directed.

Item No. 21 Complelte removal of existing old treatment on surface of walls with mechanical grinder (machine) as per specification of manufacturer paints/OBDs complete all as specified and directed.

Item No. 22 M& L a coat of alkali resistant primer over already prepred surface of walls complete all as specified and directed.

Item No. 23 M& L for preparing the entire surface with applying 2-3 mm thick putty on walls surface finished even and smooth complete all as specified and directed.Putty to be procured directly from manufacturer. (Item to be executed in stages and passed)

Item No. 24 M&L for applying two coats of oil bound distemper on wall surface with roller brush complete all as specified and directed.(Item to be executed in stages and passed)

Item No. 25 M&L for preparation of old surface of ceiling and apply two coat of white wash , complete all as specified and directed.

Item No. 26 M&L for rendering 15mm thick in CM 1:4 on fair faces or other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement up to hieght of four storey ,including scaffolding complete all as specified and directed.

Item No. 27 M&L for rendering 15mm thick in CM 1:6 on fair faces or other than fair faces of brick work or concrete surfaces of walls firnished even and smooth without using extra cement in multistorey building ,complete all as specified and directed.

Item No. 28 M&L for 5mm thick rendering in cement mortar 1:3 finished even and smooth without using extra cement on ceiling, chajja in multi storey building complete all as specified and directed.

Item No. 29 M&L for preparation of newly plastered surfaces of wall and applying 2-3 mm thick wall care putty and apply two coat oil bound distemper over one coat of primer from the same manufacture complete all as specified and directed.

Item No. 30 M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Item No. 31 M&L for preparation of newly plastered surfaces of wall and apply two coat of cement base paint over one coat of primer from the same manufacture complete all as specified and directed.

Item No. 32 S&F factory made PVC kitchen and cupboard frame of the size 75mmx40mm with a wall thickness of 4mm, made out of extruded 4mm thick pre-laminated PVC sheet reinforced with 15mmx15mm MS tube of 19 gauge thickness througout the frame and mitre cut at two corners and jointed with 2 Nos of 150mm long brackets of 10mmx10mm MS tubes.The door frame shall be fixed to the wall using 65/100mm long MS screw through the frame by using PVC fastners . A minimum of 4 Nos. of screws to be provided for each vertical member and minimim 2 Nos for Horizontal members complete all as per manufacturers specifications and directed.

Item No. 33 S&F PVC 18/19mm thick PVC moulded solid board, one side prelaminated for cabinet boxes,shutters etc. with shelf and shutters full size fitted under /above kitchen cooking platform and other platform complete all as specified and directed by the Engr-in-charge and the manufacturers specifications and drawings.

Item No. 34 S&F continous (piano hinges, mild steel bright finish or electro galvanized width of flap 30mm when open complete all as specified and directed.

Item No. 35 S&F 40mm dia cup board knob fixed with nut screw and washer of stainless steel bright finished complete all as specified and directed.

Item No. 36 M&L for 6 mm thick teak wood leaping all around for 19/20 mm shutter including polishing painting fixed withfevicol, headless screws complete all as specified and directed.

Item No. 37 S&F 100mm size hasp and staple safety type aluminium anodised with mild steel hinge pin including bolt to hinge palte and fixed screws complete all as specified and directed.

Item No. 38 S&F 100mm bore of pipe stack clamps out of suitable PVC clamp fixed with dash through fasteners and 16 mm dia round iron stay including bolt stand nuts and seuring ends of stays to wall or roof complete all as specified and directed.

Item No. 39 M&L provide precast cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate ) set in cement mortar 1:4 louvres and jallies ,40 mm thick(meassured solid ), including all moulding complete all as specified and directed.

Item No. 40 M& L Plain, solid, straight chowkats and frames made out of 2nd class hard wood (sal), wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, supplied and fixed, complete all as specified and directed.

Item No. 41 S&F 35mm thick 2nd class Hard wood rail & style (factory made) plain, framed, panelled shutter (two panel) with lock rail & panel of 12mm veneered particle board with commercial veneering on both sides. The size of rail & style as per IS :1003 (Part I), Kiln seasoned & chemicals pressure treated, complete all as specified and directed.

Item No. 42 M&L for 35 mm thick 2nd class hard wood glazed and skelton door shutter, factory made, open rebated and prepared to receive glass/guage etc. (without sash bar) edge of frames plain, chamfered or rounded, fitted with cut & mitred beads for securing glass/guage etc size of member as specified in SSR Part I Section 8 clause 8.24(a) and fixed to chowkat, complete all as specified and directed.

Item No. 43 M&L for mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming to Fe-410W (Gde-E-250 quality) complete all as specified and directed.

Item No. 44 S&F fibre glass Reinforced Plastiic (FRP)door frame shall be three legged of cross section 90mmx45mm having single rebate of 32mmx15mm to receive shutter of 30mm thickness .The laminate door frame moulded with fire retardant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs.The frame shall be covered with fibre glass from all sides . MS stay shal be provided at the bottom to steady the frame complete all as specified and directed.

Item No. 45 S&F FRP Door shutter shall 30mm thick glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacturer . Made with retardant grade unsaturated Poyester resin moulded to 3mm thick FRP laminate for forming hollow rails and styles with wooden frame and suitble blocks of seasoned wood inside at required places for fixing of fittings , cast monolithically with 5mm thick FRP panels and confirming to IS 14856-2000.complete all as specified and directed.

Item No. 46 S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized iron staples including wooden beadings or stainless steel wire staples complete all as specified and directed.

Item No. 47 S&F stainless steel of AISI 304 grade barrel tower bolt 150 mm long, extruded sections complete all as specified and directed.

Item No. 48 S&F stainless steel of AISI 304 grade barrel tower bolt 200 mm long, extruded sections complete all as specified and directed.

Item No. 49 S&F stainless steel handle of AISI-304 size 150mm size long complete all as specified and directed.

Item No. 50 S&F stainless steel handle of AISI-304 size 200mm size long complete all as specified.

Item No. 51 S&F 300mm long, stainless steel of AISI-304 grade, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and fixed, complete all as specified and directed.

Item No. 52 S&F 100 mm long (size) butt hinges, stainless steel of AISI-304with brass/bronze hinge pin, complete all as specified and directed.

Item No. 53 S&F 150mm mild steel ordinary rat tail rod pattern springs including roller and roller plate including welding where ever necessary complete all as specified and directed.

Item No. 54 S&F brass chromium plated magic eye complete all as specified and directed.

Item No. 55 Material and labour for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Item No. 56 Material and labour for preparation of new steel and iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Item No. 58 S&F in repairs sink with drainage board made of stainless steel 1 mm thick of AISI-306 for kitchen with plugs, washers and waste including bedding in cement mortar to dwarf wall or including fixing cantilever, brackets and connecting union to pipe over all size 1020 mm X 510 mm, bowl size 460 mm X 360 mm X 160 mm complete all as specified and directed.

Item No. 59 Material and labour for welding in repairs not exc 2.5 cm in length complete all as specified and directed.

Item No. 60 Supply and fix galvanized steel tubing, 15 mm bore medium grade including all fittings and short tube pieces, fixed complete to walls and ceilings or laid in floors shall be painted with bituminous paint of approved quality,The pipes should not come in contact with lime mortar or lime concrete as pipes are affected by lime etc complete all as specified and directed.

Item No. 61 All as per item No 60 above but 20mm bore.

Item No. 62 Cuttting chases pining in, making good to facings where required and pointing in cement mortar 1:3 to ends and edges of landings, steps, cills shelves, lintels etc. for concealed water tubing or concealed conduct wiring etc and making good cutting exc 10 cm not exc 20 cm grith in brick wall complete all as specified and directed.

Item No. 63 S&F in repairs vitreous china wash hand basin (flat back) white of size 550X400mm excluding taps, waste chain and plug and porcelain stopper including a pair of mild steel angle iron brackets of size 50x50x5mm duly primed and painted with two coats of synthetic enamel paint with suitable button welded or screwed for securing WHB complete all as specified and directed.

Item No. 64 S&F in repairs vitreous china squatting pan Orissa pattern long pan size 580x440mm white with integral foot rests ‘P’ or ‘S’ trap front or back inlet (excluding flushing cistern and flush pipe ) complete all as specified and directed.

Item No. 65 S&F in repairs PVC low level white flushing cistern valveless syphonic action type 10 litres capacity with inlet, ball valve, float and handle including PVC flush pipe 32 mm dia with bend and a pair of mild steel angle iron brackets of suitable size including making necessary connections to water supply pipe line and WC, complete all as specified and directed.

Item No. 66 S&F in repairs bib taps 15 mm bore chromium plated brass, fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed.

Item No. 67 S&F in repair Stop Valve 20mm dia cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or unions, complete all as specified and directed.

Item No. 68 S&F in repairs angle valve, fancy type, chromium plated brass, 15mm bore complete all as specified and directed.

Item No. 69 S&F in repair PVC connection 15mm bore and 60 cms long with two nos of brass nuts and washers complete all as specified and directed.

Item No. 70 S&F in repairs shower rose, chromium plated brass, fancy type, 125mm size, with or without swivel , any size, including fixing to steel pipe or union, complete all as specified and directed.

Item No. 71 S&F in repairs 15 mm bore pillar taps, fancy type brass with capstan head chromium plated screwed down high pressure with or without lettered “hot/cold” with long screwed shank and flynut screwed complete all as specified and directed.

Item No. 72 S&F concealed stop valves cast copper alloy screwed down high pressure, 15mm bore type chromium plated fixed in repairs complete all as specified and directed..

Item No. 73 M&L for brick work using sub class 'B' bricks,old size , straightor curved on plan exceeding 6 m mean radius built in CM 1:6 all as specified and directed.

Item No. 74 S&F in repair stainless steel of AISI-304 grade towel rack of size 600mmx300mm including a pair of brass bracket complete all as specified and as directed.

Item No. 75 M&L for prepared surface of wall and applying two coats of cement paint over a coat of primer from same manufacture complete all as specified and directed.

Item No. 76 S&F in repair brass chromium plated tubuler towel rail 20mm dia D type ISI marked 60cm long between flanges including a pair of CP brass brackets, complete all as specified and directed.

Item No. 77 S&F in repair brass chromium plated soap dish, complete all as specified and directed.

Item No. 78 S&F glazed non skid ceramic tiles in vertical surface,coloured, of size 600mm x 300mm x6 to 7mm thick on vertical surfaces such as dado/skirting etc. set and jointed with approved adhesive,including 10 mm thick rendering cement plaster in 1;4 CM and pointed in white cement with pigment to match complete all as specified and directed.

Item No. 79 M&L for rectified coloured non skid ceramic tiles of size 300x300x 7-8mm as in floors, set and jointed in neat cement slurry as per manufacturers instructions and pointed in white/ coloured cement, laid over and including cement screed bed 15mm thick in cement mortar 1:6, complete all as specified and directed.

Item No. 80 M&L for 25mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in sub base finished surface even and fair , complete all as specified and directed.

Item No. 81 M&L for rectified coloured non skid ceramic tiles (square/ rectangular) 7 to 8 mm thick, area of each tile exc .18 sqm but n exc .38 sqm in floors set and jointed in neat cement slurry and pointed in coloured cement to match including 15 mm thick screed bed in cement and sand mortar 1:6 complete all as specified and directed.

Item No. 82 All as per item No. 81 including 10 mm thick plaster on vertical surface/skirting on wall in cement and sand mortar 1:4 complete all as specified and directed.

Item No. 83 M & L for 16-18 mm thick Machine cut kota single piece stone slab for steps and size 22''x22'' for flooring over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab laid over and including 15mm thick screed bed in CM 1:6 and rounding of edges, rubbing and polishing complete all as specified and directed.

Item No. 84 All as per Item No 83 above but in skirting/dado over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

Item No. 85 M&L for 16-18 mm thick Black Granite stone work (table rubbed and polished) laid over and including15mm thick Screed bed or bedding layer in CM 1:4, as in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite,front and side of slab moulded and polished complete all as specified and directed. Note:- Granite stone slab shall be laid in single piece with rounding of edges and a grove shall be provided beneath the projected portions of stone slabs and provn of hole for gas pipe shall be provided.

Item No. 86 M&L Providing 75 mm thick cement concrete 1:3:6 type C-1, ( using 20mm graded crushed stone aggregate), as in plinth protection laid in bays not exceeding 2 Sqm each and finishing even and fair on top complete all as specfied and directed.

Item No. 87 S&F in repair stainless steel drapery Rod 25mm dia including stainless steel side caps, brackets, and rings @ 120mm centre to centre complete all as specified and directed.

Item No. 88 M&L for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs , rounded or champered on edges complete all as specified and directed.

Item No. 89 M&L for Reinforced cement concrete M-25 (Design Mix) (20 mm graded crushed stone agg) in shelves & similar items complete all as specified and directed.

Item No. 90 Use and waste of form work to soffits of suspended slabs such as roof slab, Chajja, platforms and landings etc not exc 200mm thick (horizontal or sloping) for fair finished surfaces of concrete complete all as specified and directed.

Item No. 91 S&F TMT steel bars of 10 mm dia and over,cut to length bent to shape required, including cranking bending spirally for hopping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Item No. 92 S&F in repair stainless steel peg set of 6 peg, 45 centimeter long, complete all as specified and directed.

Item No. 93 S&Fin repairs UPVC (SWR) pipes of 110 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80mm) double socketed in any length with rubber ring joints incl all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

Item No. 94 S&F UPVC (SWR) pipes of 75 mm nominal outside diameter (Type B with wall thickness 3.20 to 3.80mm) double socketed in any length with rubber ring joints incl all fittings/fixtures fixed on wall or in trenches or in floor complete all as specified and directed.

Item No. 95 S&F in repairs PVC (SWR) bends of any radius ( 110mm bore) including jointing with solvent cement complete all as specified

Item No. 96 S&F in repairs PVC (SWR) junction double,(double T, 110 mm bore), equal or unequal , including jointing with solvent cement complete all as specified and directed

Item No. 97S&F in repairs PVC (SWR) junction double,(double T , 75 mm bore), equal or unequal complete, including jointing with solvent cement complete all as specified and directed.

Item No. 98 S&F in repairs PVC (SWR) multi floor trap with grating including jointing with solvent cement complete all as specified and directed.

Item No. 99 S&F in repairs PVC (SWR) vent cowl of 110 mm bore complete all as specified and directed.

Item No. 100 S&F in repairs PVC (SWR) vent cowl of 75 mm bore complete all as specified and directed.

Item No. 101 S&F in repairs PVC (SWR) branch piece,(75 mm bore) single (single Y) equal or unequal complete all as specified and directed.

Item No. 102 M&L for 18/19mm thick prelaminated particle board, exterior grade, prelaminated both sides with decorative choice laminationwith BWR type adhesive, fixed with screws to timber frame work as in cup board shutter, loft shutters incl 6 mm thick teak wood lipping and necessary rebating for leaf shutters where required including polishing to lipping/rebating complete all as specified and directed.

Item No. 103 S&F mild steel work as in framing for sun shades, projection etc using MS square pipe and other section if required comforming to Fe 290 Gde E-165 complete all as specified and directed. Note :- Frame work to be provided over chajjas upto four store building using scaffolding and rate for same deemed to be included under this item and nothing extra shall be payable on this account.

Item No. 104 S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws and the sheet should be embedded into the wall to a depth of 25mm and the surfaces to be plastered and made good complete all as specified and directed. Note :- Steel sheet to be fixed over chhajja upto four storey building using scaffolding and rate for same deemed to be included under this item and nothing extra shall be payable on this account.

Item No. 105 S&F in repair stainless steel gratings 100mm bore size fixed with cement motar complete all as specified and directed.

Item No. 106 M&L for chipping out spilled and loose concrete cover and derusting steel reinforement of concrete column, beam, slab, chajjas, parapets and the like as directed upto 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforecement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of gaggar sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair by providing 10mm thick rendering in CM 1:3 including necessary padding, shuttering/scaffolding, formwork (upto G+4 ) complete as directed at site. Note :- (a) After placing the additional reinforecement all concrete surfaces shall be throughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions. (c) Cost of the above aspect including rendering 10mm thick plaster in CM 1:4 shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account. (d) Additional rainforcement if required shall be measured and paid under respective item.

Item No. 106A M&L guniting thickness more than 25mm, each 5mm layer or part thereof.

Item No. 107 M&L for roof treatment as per the description below:- a) Plain cement concrete average 50 mm thick 1:2:4 type B0 (using 12.5 mm graded stone aggrigate )for levelling course for providing slope in the roof @ 1:40 gradient. (b) Rendering 10mm plaster in cement mortar 1:4 using WPC @ 3% by weight of cement. c) Apply bituminous primer @ 0.3 ltr/Sqm (conforming to IS-3384) on prepared surfaces. After drying of primer apply a coat of hot blown 85/25 grade bitumen conforming to (IS-702 @ 1.20 kg/Sqm of prepared surfaces. d) Laying APP (Atatic Polypropylene) modified five layered membrane 3 mm thick and weighing not less than 4 Kg/Sqm with centre core 160 GSM/ Sqm ; core reinforced and laid with 75 mm side overlap and 150 mm end lap. The membrane shall be laid with LPG torch application and overlaps sealed and finished neatly as per the manufacturer specification and apply two coat of silver aluminum paint ..

Item No 108 M&L for rendering 15mm thick in cement mortar 1:4 with two coat of tape create mixed (1:2) with cement paste @ 500 gm per sqm as per manufacturere instruction in sunken portion of toilets, finished even and smooth without using extra cement and applying a coat of hot blown bitumen 85/25 grade as the rate of 0.70 kg per sqm and applying one coat of hot blown bitumen 85/25 grade at the rate of 2.6 kg per sqm and one layer of 0.5mm thick fibre tissue over it and finally third layer of hot blown bitumen 85/25 grade at the rate of 2kg per sqm including getting out, complete all as specified and directed.

Item No. 109 S&F Powder coated (50 micron thick), aluminium glazed/gauzed windows shutter, side hung type with 2 Nos telescopic frictional stay hinges in each shutter without sash bar aluminium box section for shutter weighing 0.55 kg/ mtr including necessary jointing cleats glazing clips rubbers packing and anodized aluminium beading screws including fittings 2 Nos tower bolt 150mm long and 1 No aluminium handle 125mm size etc in each shutter complete all as specified and directed

Item No. 110 S&F Powder coated (50 micron thick) aluminium glazed/gauzed ventilators shutters Top hung type without sash bar aluminium section weighing 0.55 kg per mtr including necessary jointing cleats glazing clips rubber packing anodised aluminium beading screws including fittings such as 01 no peg stays 150mm long, 2 Nos aluminium hinges 75mm size 2 Nos tower bolt 150mm long and 1 No aluminium handle 125mm long etc in each shutter complete all as specified and directed. Note:- Rate quoted against item No. 109 & 110 are deemed to be inclusive of all fittings and fixture required.

Item No. 111 S&F Powder coated (50 micron thick) aluminium frame for windows/ventilators with one or more rebats incl grills, jointing cleats for fixing etc complete all as specified and directed.

Item No. 112 S&F 4mm thick pin headed glass panes used in anodised aluminium glazed/gauzed windows and ventilators shutters complete all as specified and directed.

Item No. 114 M&L for precast factory made manhole cover, area of each cover n.exc 0.60 Sqm, 100mm thick with SFRC concreting including grove and hook arrangement for lifting and placing in position and sides covered by MS sheet complete all as specified and directed.

Item No. 115 S&F in repairs PVC (SWR) bends of any radius (75mm bore) including jointing with solvent cement complete all as specified and directed.

Item No. 116 Excavation in trenches, any type of soil n exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc n exc 10 sq m on plan and n exc 1.5 m in depth and getting out.complete all as specified and directed.

Item No. 117 All as per item No 116 but exc 1.5 mtr and n exc 3.00 mtr depth complete all as specified and directed.

Item No. 118 M&L cement conc 1:4:8 type D-2 (using 40mm graded crushed stone aggregate)bed to drain pipes incl packing under and haunching against the sides of pipe after they are laid and tested for 200mm bore pipes complete all as specified and directed.

Item No. 119 M&L cement conc 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) bed to drain pipes incl packing under and haunching against the sides of pipe after they are laid and tested for 150mm bore pipes.

Item No. 120 S&F 200mm internal dia of Reinforced concrete pipes, classs NP-2, incl testing, laid and jointed complete with collars complete all as specified and directed.

Item No. 121 S&F 150mm internal dia of Reinforced concrete pipes, classs NP-2, incl testing, laid and jointed complete with collars complete all as specified and directed.

Item No. 122 Returning filling in incl spreading, leveling watering and well ramming in layers n.exc 25 cm thick complete all as specified and directed.

Item No. 123 Removing excavated material (spoil) to a distance n. exc 50 mtr and depositing were directed at a level n. exc 1.5 mtr above the starting point.complete all as specified and directed.

Item No. 124 Cutting of exising 200 mm dia manholes for connecting new drains making good to pipe and rendering, cutting out exising benching for and forming branch channel (1/2round or 3/4 section ) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching required complete all as specified and directed.

Item No. 125 Cutting into exising 150mm dia manholes for connecting new drains making good to pipe and rendering cutting out exising benching for and forming branch channel (1/2round or 3/4 section ) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching required complete all as specified and directed.

Item No. 126 M&L Machine pressed precast concrete PU coated colour interlocking paver block any shape and size, with grey cement and pigment confirming to IS 5658-2006 of 80 mm thickness M-40 Grade complete all as specified and directed.

Item No. 127 Brick work sub class ‘B’ bricks straight or curved on plan built in cement mortar 1:4 using old size bricks.complete all as specified directed.

Item No. 128M&L cement concrete 1:3:6 type C-2(using 40mm graded crushed stone aggregate ) as in foundation manholes.complete all as specified and directed.

Item No. 129 M&L P C C ,1:3:6 type C1 (using 20 mm graded crushed stone aggrigate)as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

Item No. 130 Cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggrigate ) as in surface channels and drains complete all as specified and directed.

Item No. 131 Rendering 10mm thick on fair face on brick work or conc surfaces finished even and smooth without using extra cement in CM 1:4.complete all as specified and directed.

Item No. 132 M&L 100 mm thick PCC(1:4:8) type D2 using 40mm graded stone aggregate as in sub base of floor and filling as mass conc. complete all as specified and directed

Item No. 133 .Taking down concealed copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets light fitting etc. and making good disturbed surfaces of walls, floors ,etc complete all as specified and directed.

Item No. 134 M&L point wiring complete with 1.5 Sqmm single core PVC insulated unsheathed FRLS cable 1100 volts grade (ISI marked) with multi stranded copper conductor drawn through and including non-metallic rigid PVC medium grade conduit and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc and incl provn of 1.5 sqmm PVC insulated multistranded unsheathed copper conductor cable FRLS (ISI marked) as earth continuity conductor, fabricated sunken terminal box made out of 1.60 mm thick sheet steel duly painted concealed in walls, with 3 mm thick Bakelite/PVC sheet ISI marked top cover with brass/chromium plated screws and cup washers for housing switches, socket outlets, fan regulators etc completed all as specified and directed.

(a) One light/fan/bell point controlled by one way switch ( switch to be measured and paid separtely)

(b) One light point controlled by two way switch with cable 1.5 sqmm size ( switch to be measured and paid separtely)

(c) One 3 pin socket outlet 5 hole 5 Amp independent including PVC unsheathed copper conductor 1.5 Sqmm cable as earth wire connected to common earth and to earth dully socket & switches to be measured and paid separately.

(d) All as item No 134 (c) but on same board.

Item No. 135 One power point with insulated stranded copper conductor cable 4 Sqmm single core and PVC insulated FRLS 1100 Volts unsheathed copper conductor 4 Sqmm S/C as earth wire connected to dolly complete ( socket and switches to be measured and paid separately)

Item No. 136 M&L for submain wiring with two single core PVC insulated FRLS 1100 Volts unseathed stranded copperconductor cable 6 Sqmm in and including PVC concealed conduit for submain wiring and connection complete including PVC unsheathed copper conuctor cable of 6 Sqmm size S/C as earthwire. Note ;- Two run of PVC wire and one run of earth wire with one run of conduit will be measured and paid as one length.

Item No. 137 M&L for submain wiring with PVC insulated unsheathed copper conductor multi stranded 1100V grade heavy duty 2 x 10 sqmm complete drawn in new PVC conduit on surface/ceiling along with 1x10 Sqmm PVC insulated unsheathed copper conductor multi sranded cable for continuous earth wire and duly connected to common earth dolly all as specified and directed (The specified runs of single core cables and specified runs of earth continuity conductors and the relevant conduit with accessories shall be measured as one run length).

Item No. 138 M&L switch piano flush type 5 Amp SP one way .

Item No. 139 M&L switch piano flush type 15 Amp SP one way.

Item No. 140 M&L socket outlet 5 pin 5 Amp flush type .

Item No. 141 M&L socket outlet 2 in 1,3 pin 5/15 Amps.

Item No. 142 S&F ceiling rose surface PVC 65x50mm type with three terminal.

Item No. 143 M&L in replacement regulator electronic switch type 5 steps suitable for 1200/1400mm sweep 230 volts complete all as specified and directed.

Item No. 144 M&L in replacement bell push single pole 6 Amps all as specified and directed.

Item No. 145 M&L in replacement bell electric (dingdong) 230 volt, SP complete all as specified and directed.

Item No. 146 M&L in replacement insulated body, angle hoder (metal ring) with back plate ISI marked complete all as specified and directed.

Item No. 147 S & F LED bulb 14 watt, 1400 lumen output, 6500k suitable for B-22 base complete all as specified and directed.

Item No. 148 M & L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to earth lead GI 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dai and frame all as shown in electric plate No 3 of SSR Part I (2009) including testing ion completion all as directed

Item N. 149 M&L MCB DB SPN 8 way horizontal, IP-43 protection, double door 240 volts, AC 50 Hz with for MCB SPN as incomer and DP/SP MCB as out going with tinned copper Bus bar 200 Amps cap with insulated neutral link, earth link complete all as specified and directed.

Item No. 150 S&F in repair, MCB DP 40 Amps 240 volts, 10 KA 50HZ 'C' curve complete all as specified and directed.

Item No. 151 S&F in repair, MCB SP 6 to 32 Amp 240 Volts, 10KA 50HZ 'C' curve complete all as specified and directed.

Item No. 152 S&F LED batten luminaries surface mounted, 4 feet, system wattage of 22 watt, system level efficiency of the luminary is > 90 Im/Watt including connecting up with PVC sheathed 1.5 sqmm 3core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

Item No. 153 S & F pressure die cast aluminium housing LED street light luminaires with IP66 deg. of protection suitable for 45 watt LED fitting duly fixed on 40 mm dia GI mast including 50X 6 mm thick MS flat with suitable size of fastner including making connection flexible copper conductor cable from ceiling rose to fitting complete all as specified and directed. Note : The Contractor quoted rates include all accessories like suitable GI pipe mast, 50x6 mm thick MS flat, fashner, nut & bolts, suitable length of flexiable wire.

Item No. 154 M&L in replacement distribution board TPN 4 way load line with provision of MCCB 125 Amp incomer and including 200 Amp rated bus bar,415 Volts and Iincluding outgoing SP/TP MCBs.

Item No. 155 M&L in replacement MCCB 125 Amps, 16 KA, 4 Pole with adjustable thermal & fixed magnetic complete all as specified and directed.

Item No. 156 S&F LED batten luminaries surface mounted, 2 feet, system wattage of 10 watt, system level efficiency of the luminary is > 90 Im/Watt including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

Item No. 157 S&F in repair decorative wall mounting CITY-1/Comet Decorative wall light fixture made up of polycarbonate, with provision for 14 watt retrofit LED bulb (B-22 base).

Item No. 158 Taking down defective /UNSV electric meter shifted to MES store yard, S/F Tamper proof, dfigital type, electronic energy meter with optical port single phase 240V, 50 Hz, 10-60 Amps complete all as specified and directed by Engr-in-charge.

Item No. 159 S&F 10 watt bulkhead fitting with powder coated die cast aluminium housing with glass/non yellowing polycarbonate cover IP 65 protection, system level efficiency of the luminary is > 90 Im/Watt including connecting up with PVC sheathed 1.5 sqmm 3 core copper conductor flexible wire from ceiling rose to fitting fixed complete all as specified and directed.

Item No. 160 S&F in replacement main switch TPN 200Amp including fitting accessories complete .

Item No. 161 M&L switch piano flush type 5 Amp SP two way .

Item No. 162 S&F exhaust fans AC single phase 230/240 V of size 300 mm sweep with louvre for fixing of exhaust fan complete all as specified and directed.

Item No. 163 M&L for breaking the old existing wall and making provn of a round hole for fixing of 300 mm sweep exhaust fan& 230mm fresh air fan for toilet including making good to the disturbed wall/ portion and matching with existing colour.all as specified and directed.

Item No. 164 M&L for cutting steel tubing to required length for insertion of new Tee Branches, reducer in any position of 15mm dia pipe line complete all as specified and directed.

Item No. 165 S&F tubes, 'medium grade', galvanised, with all fitting; for fixing concealed in wall complete of 15mm bore with complete fitting and fixture complte all as specified and directed by Engr-in-charge.

Item No. 166 S&F of Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of cap 15mm bore complete all as directed

Item No. 167 S&F Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed of cap 15mm bore complete all as directed

Item No. 168 S&F PVC connection 15 mm size for cold water with PTMT nuts of length 450 mm complete all as specified and directed.

Item No. 169 S&F CP connection 15 mm size with for hot water with PTMT nuts of length 450 mm.complete all as specified and directed.

Item No. 170 S & F Geyser 25 Ltrs, vertical mount, 5 star rated, glass line coated tank with adjustable thermostat, suitable for 230 volt, 1.5 KW , 50 Hz electric supply .

Item No. 171 S&F stop valves 15 mm bore CP With crutch or butterfly handle, screwed both ends for iron pipe or unions, complete all as directed.

Item No. 172 Supply and fixing ceiling fans AC single phase 230/240 V of size 1200 mm sweep including fan hook set fabricated out of zinc coats MS flat iron heavy duty fixed in roof with suitable size making connection with three core flexible, copper cable pvc insulated of suitable length and marking of fan no with black paint complete all as directed by Engr-in-Charge.

Item No. 173 S & F LED bulb 9 watt, 900 lumens output, 6500K suitable for B-22 base complete all as specified and directed.

Item No. 174 Taking down fan, sealing cable end, dismantling blades and removing fan and blades deposited to MES store yard complete all as specified and directed.

Item No.175 Hanging only ceiling fan (M.D supply) and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed.

Item No.176 S&F fresh air fan 230/250 mm sweep with louvers including connecting with suitable size of cooper conductor from ceiling rose to fan and making hole of suitable size and matching with the existing colour of wall complete all as specified and directed.

M/s Puja Construction Company

M/S SURAT SINGH AND SONS

Third Wave Services Pvt Ltd

M P TYAGI ENGINEERS AND CONTRACTORS

M/s VINOD KUMAR SHARMA

India Guniting Corporation

Global Enterprises

N K Gupta Builders Pvt. Ltd.

PARDEEP ELECTRICALS AND BUILDERS PVT LTD