SPECIAL REPAIRS TO BLDG NO P189 AT AUNDH UNDER GE MH AND RH KHADKI

Amount

Demolition of cement concrete unreinforced of any description and in any position, not otherwise specifically provided for and removing the same off the primisses complete all as specified and as directed by Engineer-in-Charge.

M & L for cement concrete M-15 grade (Nominal Mix) using 12.5mm graded stone aggregates for filleting, benching, slightly rounding or chamfering on edges, filling undulations / depressions in roof surface, providing concrete platform for tanks wherever required complete all as specified and as directed by Engineer-inCharge.

Taking down / removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and disposing off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L providing water proofing plaster on slab average thickness 10mm in CM 1:3 mixing with liquid water proofing compound all as per manufactureres instructions, finished even and smooth without using extra cement all as specified and directed Note : Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

Supply only liquid water proofing compound hydroseal-W+ or eqivalent (for plaster hardening, to control efflorescence & fungal growth) as approved by GE.

M&L for cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry in CM 1:3 complete all as specified and directed

M & L for applying APP (Atactic Poly Propylene) bitumen membrane 3mm thick APP modified weight not less than 3.60 Kg/Sqm reinforced with non woven polyester fibre of weight 160 gms/sqm as center core and without multiple layers of polyethylene, finished on top and bottom with 7 micron thick flammable polyethylene, applied by thermo fusion using LPG torch on the bottom portion of the membrane, after applying a coat of bituminous primer 0.40Kg/Sqm over roof ( An overlap of 100mm & 150mm shall be provided on sides and ends respectively ) finally applying a coat of solar reflective bitumen aluminium paint over the membrane complete all as per manufacturers instructions.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level ) all as specified and directed

M&L for waterproofing treatment to RCC sunken slab complete all as specified and directed by Engineer-in-Charge. Make: PIDILITE, Dr Fixit , FOSROC, SIKA, MC BUCHEMIE, ROFF etc or equivalent. Note:- Tiling work will be measured and paid separately under relevant item of this BOQ.

M & L PCC M-5 grade (Nominal Mix) using 40mm graded aggregate as in mass concrete or as in sunken portion or floor complete all as specified & directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing coat), removing serviceable tiles and rubbish off the premises all as specified and directed by Engr-in-Charge.

M & L for 25 mm thick PCC M-15 grade (Nominal Mix) using 12.5 graded stone aggregate as in base of floors complete all as specified and as directed by Engineer-in-Charge.

M&L Coloured Non Skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over & including 15 mm thick screed bed in CM 1:4 complete all as specified.

As per item No 13 above but as in skirting /dados over and including 10mm thick rendering as in backing coat in CM 1:4 complete all as specified and directed.

M&L Non skid ceramic colour tiles 7 to 8mm thick (square /rectangular ) area of each tiles exceeding 0.06 sqm but n exc 0.11 sqm in floors etc in neat cement slurry and pointed in white or Coloured cement to match over and including 15mm thick in CM 1:4 screed bed or bedding layer of mortar for laying floor finishes

M&L glazed ceramic tiles on vertical surface 450 x 300 x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the work over & including 10 mm rendering as in backing coat in CM 1:4, all as specified and directed.

Demolition of Brick/PCC solid block masonry or stone masonry built in cement mortar/cement lime mortar including removing the debries pff the premiesses complete all as specified and directed.

M&L for Pre-cast cement concrete block masonry of PCC 1:3:6 Type C1 using 20mm graded stone aggregate with solid blocks straight or curved on plan, exc 6m mean radius and exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar

M&L 20 mm thick Granite slab machine cut bedded and jointed with grey cement and pointed with white cement and adhesive of pigment to match the shade incl cutting and polishing laid over and including cement screed 10mm thick in CM 1:4 complete all as specified as directed by Engr-in-Charge.

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/ dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete fixed over and including backing coat of 10mm thick in CM 1:4 all as specified

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations.

M&L for 20-25 mm thick machine cut machine polished Kota stone slab flooring laid and jointed in neat cement slurry mixed with pigment to match the shade including cutting and polishing over and including 15 mm thick screed bed in CM 1:3 complete all as specified and directed by Engr-in-Charge.

All as item No 23 here in before but in skirting but single piece for step riser over and incl 10 mm thick rendering in CM 1:3 to receive kota stone/slab etc all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls,ceilings etc. including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L rendering 15 mm thick (10mm + 5mm) plaster on other than fair face of brick work in CM 1:4 and surface finished even and fair by mixing liquid water proofing compound as per manufacturers instructions complete. Note : Liquid WPC shall be measured & paid seprately under relevant item of this BOQ.

M&L for preparation newly plastered surfaces of walls/ceilings and applying two coats of weather proof acrylic exerior paint (100%) Acrylic over one coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified.

M&L for complete removal of existing treatment of old surfaces and applying two coats of weather proof acrylic exterior paint (100%) Acrylic over a coat of self primer including scaffolding, trestles, ladders, cradles and necessary safety measures complete all as specified and directed by Engr-in-Charge.

M&L for rendering plaster 10mm thick in CM 1:4 finished even & smooth with thin layer of sagol finish not less than 1mm thick as in ceiling complete all as specified and directed

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed by Engr-in-Charge.

M & L for applying one coat of white wash on celing on old surfaces including preparation of old surfaces including cleaning smoke efflorocense of any type or spot of nail filled with putty complete match to old surface all as specified and directed.

M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface with a thin layer of sagol not less than 1mm thick all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for complete removal of existing finishes and applying two coats of oil bound distemper on walls over a coat of alkali resistant primer including chalk whiting preparation of old surfaces, on plastered surfaces prepratary to distempering all as specified.

M&L for preparation of newly plastered surface and applying three coats of white wash on ceiling complete all as specified and directed.

M& L for complete removal of existing finishes and applying three coats of white wash on walls including preparation of old surfaces all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 Sqm but n. exc 4 sqm all as specified and directed.

S&F 125x60 mm pressed steel frames made out of 1.25mm steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., with one shop coat of red oxide primer complete, as specified, supplied and fixed all as specified and as directed.

M&L for PCC cement concrete M-10 grade (nominal mix) using 12.5 mm graded stone aggregate in door and windows frames, any size, single or double rebated, including arrangement for fixing of hinges and fixtures as required

S & F 35mm thick factory made second class hard wood plain, framed , panelled shutter (2 panel) with lock rail and panel commercial ply or 12 mm veneered particle board of 9 mm B.W.P commercial veneering on both faces.The size of rail and stile as per IS:1003 (part-I), kiln seasoned and chemically pressure treated all as specified and directed.

S&F 35mm thick (2nd Class hardwood) factory made gauzed and skeleton door shutters, open rebated and prepared to receive glass, gauze , etc (without sash bars) , edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc, sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a), supplied and fitted to chowkats all as specified and directed.

S & F Aluminium, anodised, barrel tower bolts of extruded section 200 mm long.

S & F Aluminium handles, cast type, anodised size 150 mm long.

S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as directed.

S & F in repair Mild steel Butt hinges100 mm long, medium weight, cold rolled steel.

M&L for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of old wooden surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed by Engr-in-Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n.exc 1.5 Sqm each all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing all as specified and directed.

S & F MS Butt hinges 75 mm long, medium weight, stainless steel.

S&F factory made PVC solid panel door shutter 30mm thick (style) connecting of frame made out of MS tube for top and bottom rail. MS frame shall be coverd withheat moulded plain coour PVC 'C' channel having a PVC sheet strips of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail of either side and as gap insert for toprail and bottom rail panellinn of plain colour PVC to be fitted in the ms frame welded/ sealed in the stiles and rail with suitable PVC sheet and loading and jointed together with solvent cement, supplying and fixing in the frame at site all as directed.

S & F Aluminium, anodised, barrel tower bolts of extruded section 125mm long complete all as specified and directed.

S&F of 125 mm size Aluminium handles, cast type, anodised all as specified and directed by Engr-in-Charge.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, with a shop coat of red oxide primer complete with glazing bars, dovetailed or welded all as specified and directed.

S&F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, with a shop coat of red oxide primer complete without glazing bars, dovetailed or welded (for mosquito proof shutter) all as specified and directed.

S&F Framed work such as grills, gratings, etc., with ends of bars shouldered and/or ri-veted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0.

S& F 3 mm thick sheet glass ordinary quality and glazing with oil putty/wooden beading in square n.exc. 0.5 sqm in each pane complete.

S&F in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18mm fixing to steel window with tinned tacks or galvanised wire staples complete all as specified and directed.

M&L for preparation of new steel surfaces over 10cm in width or girth and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete all as specified.

S&F aluminium louvered ventilators of section size 100mm x 25mm x 1.50mm including frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc. including taking down existing steel ventilator all as directed by Engr-in-Charge. Note : Glass & wire mesh shall be deemed to be included in unit rate quoted.

M & L for preparation of old steel surfaces exc 10 cm width or girth and applying one coats of synthetic enameled paint complete all as specified and directed.

M&L for spot welding for repairing steel windows and ventilators hinges, brackets, steel handle, etc. all as sepcified and directed.

S&F in repairs powder coated aluminuium pipe 20 mm dia as in curtain rod fixed to brackets all as specified and directed. Note : Brackets shall be measured and paid separately.

S & F in repairs powder coated aluminium brakets fancy type for curtain rods of 20mm dia ,all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases for concelaed water tubing or concealed conduit wiring etc. and making good, cutting not exc 10 cm girth complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required or removed from site.

Taking up or down 20 mm bore steel tubing and connections including disconnection of fittings and cleaning for refixing where required or removed from site.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Refixing tubes of 15 mm bore, any grade, to walls and ceiling or laying in floors complete with new fittings complete. Note : Steel tubing obtained from taking down shall be re- used.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S&F in repair rotational moulded polyethylene water storage tanks of capacity 500ltr hoisted and fixed in position including 25mm ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed all as specified and directed. Note : Unit rates is deemed to be included the cost for removing old tank of any description.

S & F in repairs 15mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipes and fixed.

S & F in repairs 20mm dia bore Gun metal, globe or gate valves with Iron wheel head, screwed both ends for Iron pipes and fixed.

S & F in repair angle stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed - bore dia of pipe 15 mm.

S & F in repair stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions & fixed - bore dia of pipe 15 mm but fancy type with long shank and cup ( concealed type) complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm dia fancy type Bib taps, cast copper alloy CP with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F in repair, Chromium plated shower roses with or without swivel joints, 125mm size, including fixing to steel pipe or union

Supply and fixing PVC connections 15 mm size with PTMT nuts of length 600 mm complete al as specified and directed by Engineer-in-Charge.

S&F in repair 110 mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed in trenches complete all as specified.

S&F in repair 110 mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed on walls complete all as specified.

S&F in repair 75 mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed in trenches complete all as specified.

S&F in repair 75 mm bore PVC (SWR) pipes type 'A' single socketed, in any length with rubber ring joints, fixed on walls complete all as specified.

S&F in repair, 110 mm dia bends any radius all as specified and directed.

S&F in repair, 75 mm dia bends any radius all as specified and directed.

S&F in repair, 110mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal all as specified and directed.

S&F in repair, 75mm bore PVC (SWR) branch pieces, single (single Y) equal or unequal all as specified and directed.

S&F in repair, 110mm bore PVC (SWR) junction single (single T) equal or unequal all as specified and directed.

S&F in repair, 75mm bore PVC (SWR) junction single (single T) equal or unequal all as specified and directed.

S & F in repairs Vitreous China Squatting pan Orissa pattern long pan, size 580 mm x 440mm white with `P' or `S' trap, front or back inlet and foot rests any pattern including connection to trap and to flushing pipe, anti-syphonage pipe etc, including trap set in and including concrete complete including making good to floor all as specified and directed.

S & F in repair PVC valveless syphonic action type flushing cistern (Low or high level) of 10 litre capacity, white/coloured with inlet ball valve, float, handle including fixing brackets and 32 mm bore PVC flush pipe etc complete all as specified and directed.

S&F in repairs vitreous china wash basin white, flat back of size 450 x 300mm, excluding taps, waste chain & plug & porcelein stopper but including brackets, cutting for and pinning in ends of brackets including waste coupling and waste pipe all as directed

S&F in repair pillar taps fancy type cast copper alloy with capestan heads chromiun plated screwed down high pressure with hot & cold with long screwed shanks and fly nuts all as specified and directed.

S&F in repair, stainless steel sink, 1mm thick, kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm all as directed.

S&F plate rack made of stainless steel 1mm thick and overall size 915mm x 915mm x 255mm, inlcuding taking down old unserviceable complete all as specified and directed.

S&F 20mm dia or over pre polished and moulded granite corner shelf fixed in CM 1:3 to wall and maked good with putty filling with colour match to existing surface complete all as specified and directed by Engr-in-Charge

S&F in repairs tubular towel rail 20mm dia, D type 60cm long between flanges brass chromium plated all as specified and directed.

M&L 75 mm dia cast iron floors trap with grating including jointing to waste pipe fixed in cement concrete M-15 grade (Nominal Mix) using 20 mm graded stone aggrigrate complete all as specified and directed.

M&L for 75mm thick PCC M-10 grade (Nominal mix) as in plinth protection finishing the surface even and smooth without using extra cement.

M & L for 75mm PCC M-7.5 grade (nominal mix) using 40 mm graded stone aggregates as in sub base of floor complete.

S&F Pre polished chequered cement concrete tiles glossy and rubburised finish colour 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors over & including 15mm thick screed bed in CM 1:4 under tiles including all as specified and directed by Engineer-in-Charge.

S&F plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together wit glue pinned at joints complete all as specified and directed.

S&F in repairs 18/19 mm prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as sepcified and directed.

S&F in repair Hasp and staple 150mm long, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws.

S&F 75mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed

S&F 100mm long Aluminium handles, cast type, anodised

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit(credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

M & L for point wiring complete with and including 1.5 sqmm (nominal area) single core multi stranded copper conductor PVC insulated but unsheated FRLS cable 1100 Volts drawn in to and including concealed PVC conduit of suitable dia includings sunken to wall including its accessories such as tee, bend ,elbow, socket and chisselling on wall complete and al so making good the disturbed surfaces of wall / ceiling by cement mortar 1:4 including painting to existing surfaces and also including 1.5 sqmm PVC insulated and PVC unsheathed single core multistranded copper conductor FRLS cable 1100 V grade as earth wire including concealed MS terminal box ISI marked of suitable size / 3 mm thick hylam sheet on MS terminal box for housing switch, socket,regulators etc complete for the following:-

One light point controlled by one switch

One Fan point controlled by one switch

One 5 pin 6 Amps socket outlet on independent board.

One 5 pin 6 Amps socket outlet on same board.

All as per item No. 108 here-in-before but wiring with 2.5 sqmm single core multi stranded copper condcutor 1100 v grade PVC insulated but unsheheted copper conductor FRLS cable 1100 volts grade and 2.5 sqmm PVC insulated but unsheathed FRLS cable as earthwire for 16 Amps power point on independent board complete all as specified and directed by Engr-in-charge.

S & F switch piano flush type 240 volts single pole one way 6 Amps all as specified and directed

S & F socket outlet 5 pin 6 Amps shuttered flush type all as specified and directed.

S & F switch piano flush type 240 volts single pole one way 16 Amps all as specified and directed.

S & F socket outlet 2 in 1, 3 pin, 6 and 16 Amps flush type all as specified and directed.

S & F PVC ceiling rose / Angle Holder / Batten Holder surface type three terminals type all as specified and directed.

S & F fan regulators electronic step type suitable for 1200/1400 mm sweep ceiling fans.

Supply and fixing LED lights fitting 1x 22W, 220V, AC decorative box type, holder including LED tube rod connecting up with three core flexible copper conductor cable of suitable size 0.5 sqmm from ceiling rose complete all as specified and directed by Engr-in-Charge.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size 0.5 sqmm complete all as specified and directed.

Supply and fixing LED street light fitting 36 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

M & L for sub main wiring but using two single core muiltistranded PVC insulated copper conductor FRLS cable of size 4.0 sqmm 1100 volt grade drawn suitable size of PVC conduit of suitable size and accessories concealed in wall PVC multi standard copper conductor FRLS cable in green colour for continious & making good disturbed surfaces of wall/floor/ceiling to match with existing surface, including taking down the existing u/s submain wiring complete all as specified and directed by Engineer-in-Charge. Note : Two runs of 4 Sqmm cable, one run of 4 Sqmm earth cable and one run of PVC conduit shall be measured as one unit length.

S & F MCB distribution board in repair or replacement factory made SPN 4 way, 240 Volts, double door complete with 200 Amps rated copper busbar complete all as specified and directed. Note: The rate deemed to be included for taking down old unserviceable MCB DB by cutting / chasing wall, plastering and making good all disturbed surfaces matching with existing surface.

Taking down old existing fan and S & F for New Ceiling fan, complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and exisitng C/F deposited to MES store yard complete all as specified and directed

Material and labour for earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete. Note : Rate of item is deemed to be included for excavation in hard rock, by compressor machine to achieve required depth.

M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn inconduit / pipe or fixed to poles or any other indicated suituation for loop earthing etc. as required 4 mm dia galvanised iron or steel wire

Cutting chases, pinning in concrete block or slab, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 20cm girth.

M&L for rendering 10mm thick, on fair faces of brick work or concrete surfaces of walls in CM 1:6 finished even surface all as specified and directed by Engr-in-Charge

M/S SANDEEP CONSTRUCTION COMPANY