Construction of Library at krishnapura Ward No. 17, Under MC Panipat. Urban

Recovery of old and usable bricks

`Supply and Erection of Timer Contractor, DP, MCB mounted on Bakelite sheet and Installed in water proof CRCA Sheet 18 SWG duly painted with powder coated paint Box of Size 12``x15``x5`` Sintex/Semens make pvc insulated pole boxes of suitable size duly lockable including Input and Out Put Connectors Bakelite/Porclein of 63A Rating and neccessary service cable up to 10 mtr complete with internal copper wiring and installing the same on pole/pedestal with suitle means at hieght desired by Engineer in charge to aviod theft upto entire satisfication of engineer incharge with following specification. Timer :-Quartz Analog 24 Hour Operation (G.E/LandT/Siemens/Indoasian/CandS) Contractor :- 3Pole 32A, 415Volt. (Schnider/LandT/Siemens/Indoasian/CandS), DPMCB :- 40A 2pole. (G.E/LandT/Siemens/Schnider/CandS)`

SUPPLYING, INSTALLATION, TESTING and COMMISIONING OF 13 PASSENGER LIFTS OF FOLLOWING SPECIFICATION HAVING 5 and 8 STOP S AND APPROXIMATE TRAVEL DISTANCE OF 24 M HAVING FOLLOWING SPECIFICATIONS Product DescriptionElevator SpecificationsNumber of Persons 15Rated Load 1020 kgNumber of stops 5Number of Access sides 1Floor designations B,S,1,2,3Drive System Alternating Current Voltage Frequency (ACVF)Type of controller Full Collective control - SimplexSpeed of travel 1.5m/sCar Size 1575 mm (W) x 1500 mm (D) x 2239 mm (H)Door Width 900 mmDoor Height 2100 mmRated output motor 7.7 kwCar DesignCar walls finish in Stainless Steel HairlineLED spot in ceilingCar doors finish in Stainless Steel HairlineCar door in Stainless steel finishGranite Flooring finish in Black SeaDeco Ceiling finish in Stainless Steel Mirror 304Full height mirror on rear car panel Car Operating PanelStylish, touch sensitive glass panelDoor open/close and alarm buttons OF MAKE OTIS,KONE SCHINDER

PVC/XLPE INSULATED (HEAVY DUTY) ELECTRICAL CABLES FOR WORKING VOLTAGE UPTO AND INCLUDING 1100 VOLTS TO IS:1554 (PART-I) 1988/7098 (Part – I) WTH ALUMINIUM CONDUCTOR – ISI MARKED POWER CABLE- ALUMINIUM CONDUCTOR 16 Sq mm 4 core aluminium un-armoured cable Make: Grandlay, Havells/POLYCAB

`Supply and eraction of PVC/XLPE Insulated (Heavy Duty) Electrical cables for working voltage upto and including 1100 Volt to IS: 1554 (Part-I) 1988/7098(Part-I) 1988 with coper conductor -ISI Marked 2.5 sq mm 3 Core copper Unarmoured Cable Make: Grandlay/Havells/KEI/RR Keble/POLYCAB`

Poles- are combination of Galvanised grooved steel tubes having 105mm dia at bottom and 81mm dia at Top with decorative Cast Iron Padestal base and Embellishments-Q1. The Poles are primer coated and painted with Polyurethane paint any colour. The Poles has a service window at the bottom comprising four way 25Amp connector terminal and a MCB. Poles has a mild steel base plate having four numbers mounting holes as per drawing and can be mounted with four numbers anchor bolts The Decorative ornamental Single arm bracket made out of Galvanised steel tubes with cast alum. embellishments and suitable for drop down luminaires. The brackets are primer coated and painted with polyurethane paint. Fixture made of Cast alum. housing with Power LED’s are mounted metal clad PCB’s and then metal clad PCB`s and then LED`s and PCB assembly are mounted on extruded aluminium Heat sink and fitted with LED driver. A UV stabilized PC/PMMA diffuser is provided for Glare Free Lighting with high Visual comfort. (Makes Havells, Surya,Bajaj, Twinkle, Jaguar)

P and F Contactor as per NS MNX 125 with 5 years warranty Make: Make: Indo Asian/L and T/C and S

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required.(NS) 30 Watt - 2x2 Recessed Mounted LIGHT (MAKE - Philips, Havells, WIPRO)

Providing and fixing in position 8` SS handle for (flush doors) cupboard shutters i/c SS screws complete

Providing and fixing of MUNICIPAL CORPORATION KISHANPURA LIBRARY in Acrylic Letters with light of 24` Height with power Supply and Warrenty of 2 years with fittings complete with all respect................

Providing and fixing 50mm Wooden Blinds with single cord operator complete with all respect.

Providing and fixing of signages of toilet of size 300x450mm as per design complete in all respect up to the entire satisfaction of Engineer-in-charge of the work.

Providing and fixing of signages of department names of size 600x1200mm as per design complete in all respect up to the entire satisfaction of Engineer-in- charge of the work.

Providing and fixing of signages of fire exit names of size 800x300mm as per design complete in all respect up to the entire satisfaction of Engineer-in-charge of the work.

Providing and fixing of wooden polymer composite panel and WPC Louvers of size 160 x 2900 x 8.5mm as per design complete in all respect as per the entire satisfaction of engineer in-charge

Providing and Fixing of Acoustical Sound Suspenders™ made of Acoboard™ and Woodperf™Acoustic Panels for achieving the best NRC Value up to 0.90. Size of the Acoustical Sound Suspenders™1200*300*30mm. Construction details are as follows 9mm thick Acoboard fixed over 12mm thick Woodperf AcousticPanels both the sides with rigid fixation. Design of the Acoustical Sound Suspenders as per the size (1200*1200*30mm)with Top and bottom side flat. The Acoustical Sound Suspenders™ marked with hanging arrangement on the rear sides, each Clouds having distancing from each Clouds as per the design intended to the architect. The Suspenders to be suspended over required accessories like Uni strut channel using the locking Clip tied by Thread rod or Hanger Wire kit, cable finishing hook. Acoboard and Woodperf Panels are Certified by GRIHA V.2019 criterion: 11, GRIHA V.2015 criterion: 11 and GRIHA V. 3.1 criterion: 29. Installation of the Sound Suspenders as per the instruction lay Down By the manufacturer as per design complete with all respect . as per the entire satisfaction of engineer in-charge

Providing and fixing of Acrylic Braille Tactile map with MS Frame of 304 grade 1.5mm matt sheet complete in all respect up to the entire satisfaction of Engineer-in- charge of the work.

Providing and fixing of SS Braille handrail signage of 304 grade 0.5mm thick with emboss dots of size 200x50mm complete in all respect up to the entire satisfaction of Engineer-in-charge of the work.

Providing and fixing customize Wisteria Feather Paper Wall covering in non-woven paper having width of 108 inches of 260 GSM as per design complete in all respect as per the entire satisfaction of engineer in- charge

Providing and fixing of floor vinyl strickring 3m pasting on floor complete in all respect as per the entire satisfaction of engineer in-charge

Recovery of MS Railing

Providing and installation of Brother Laser jet AIO Printer 4000 DW . Complete in all respect as per Satisfaction of Engineer-in-charge..(Make: HP, Brother, Canon)

Providing and installation of HP Laser jet AIO Printer 126NW Complete in all respect as per Satisfaction of Engineer-in-charge...(Make: HP, Brother, Canon)

Providing and installation of HP 379 DW Complete in all respect as per Satisfaction of Engineer-in-charge... (Make: HP, Brother, Canon)

Supply, installation, testing and commissioning of 27` All-in-One Desktop-computers 13th Gen Intel® Core™ i5, Windows 11, microprocessor, 16 GB RAM, 1 TB SSD, Windows latest embedded OS and SQL Data Base, serial Interface port,USB Ports, compatible display card, keyboard, Mouse. (Make :- Dell / HP/LENOVO)

Providing and fixing of grafity on wall as per design complete with all respect as per the direction of engineer-in-charge

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required.(NS) 1200MM 20W LED Tube light with accessories as complete required.Philips, Havells, WIPRO)

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required.(NS) 900MM 28W LED Tube light with accessories as complete required.Philips, Havells, WIPRO)

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required.(NS) … 12-Watt Recessed LED (ROUND TYPE LED LIGHT) Philips, Havells, WIPRO)

Supply, Installation, testing and Commissioning of the following lighting fixtures with all fixing accessories etc. complete as required.(NS) … 100-Watt FLOOD LIGHT Philips, Havells, WIPRO)

Incoming: 1 Nos. 250 Amp FP MCCB OF 16 KA Breaking Capacity Metering for incoming: 3 nos 250/5A Class 1, 5 VA Burden CT`s for metering and 1 nos associated Neutral CT for earth fault module. Digital flush type class -1.0 accuracy multifunction meter with RS-485 communication port for measurement of PF, V, A, Hz, equivalent to EM6459 NG, with 3 Nos. current transformers of required ratio, 5 VA Class 1.0 Phase indication Lamp and ON/OFF indicating lamps with MCB as backup protection. Bus Bar: TPN Aluminium busbars aluminium three phase and neutral busbars rated at 400 amps, 16 KA, insulated with heat shrinkable coloured PVC sleeves and clip on shrouds for joints. Current density of Bus Bar to be 1.0 sq.mm / amp. Outgoing : 9 nos. 63 amps 25 kA 440 volt FP MCCB with overcurrent and short circuit and earth fault module, with heavy duty solid detachable neutral link complete with: Complete Set as required above

Supplying installation testing and comissioning of following capacity True Online dual conversion(Pure Sine Wave), microprocessor based Online UPS System with five years warantee having pollution free instantaneous true sinewave control and without inbuilt isolation transformer, 3 Phase AC input and 3 phase AC output, LCD display and indication for various electrical parameters, LED indication with alarm for major fault, provision for remote indication and provision of communication to BMS system through RS 485/RS232/Modbus port etc. The UPS system shall be as per detailed specifications and shall be complete with parallel redundant kit, battery bank for providing 30 minutes backup time with SMF batteries having minimum 2 years warrantee, with all connections interconnections cables, MS stand for battery bank etc. complete as required Specifications of UPS a) Capacity : 20 KVA Capacity Online UPS System b) Technology : True Online dual conversion(Pure Sine Wave) Input Parameters a) Input Voltage range : 352-475VAC, 3-F AC Supply b) Rated frequency : 50Hz/ 60 Hz ± 10% c) UPS Power factor: 0.99 or better lagging d) Harmonic distortion: with Linear load =3% Output Parameters a) Rated Voltage: 415 V ± 10% b) Frequency: 50Hz ± 0.5Hz c) Output wave form: Pure sine wave `d) Overload capacity: 150% of rated load for 1 minutes 125% of rated load for 10 minutes` General Parameters a) Ambient operating temp: Upto 40º C or better b) Noise Level : = 65 db at 1.5m distance or better c) Overall efficiency: 94% or better d) Computer interface: RS232 / RS485 e) Cooling: Forced Cooling f) Bypass: Manual/Static

IN FLOOR/ SCREED RACEWAY Supply and Fixing of factory fabricated pre-galvanised sheet steel raceway in 2mm thickness for bottom and sides and 2mm/ 3mm thick top cover including openable top cover floor junction boxes made from 2mm thick pre-galvanised GI sheets for bottom and sides and 3mm thick GI top cover complete with rubber gasketing beneath the top cover. The junction box shall be suitable to accommodate GI floor raceways as specified above, as called for including necessary civil work such as chase cutting in screed, fixing/ jamming the raceway, aligning and leveling and finishing with sand cement plaster and chicken wire mesh: 40mm Depth 100mm x 40mm (2mm top cover)

Supply and Fixing of factory fabricated pre-galvanised sheet steel raceway in 2mm thickness for bottom and sides and 2mm/ 3mm thick top cover including openable top cover floor junction boxes made from 2mm thick pre-galvanised GI sheets for bottom and sides and 3mm thick GI top cover complete with rubber gasketing beneath the top cover. The junction box shall be suitable to accommodate GI floor raceways as specified above, as called for including necessary civil work such as chase cutting in screed, fixing/ jamming the raceway, aligning and leveling and finishing with sand cement plaster and chicken wire mesh: 150mm x 40mm (2mm top cover)

Supplying, installation, testing and commissioning of heat detector operating at 50C/57C with rate of rise sum fixed tempreature (dual thermistor) type with mounting base complete with all connection etc. as required. (MAKE AGNI QS-951-2L)

Supplying, installation, testing and commissioning of smoke detector with builtin LED and mounting base complete with all connection etc. as required. (MAKE AGNI QS338 2L)

Supplying, installation, testing and commissioning of manul call boxes of MS construction in surface/recess complete with glass and puch button etc. as required. (MAKE AGNI AD110)

Supplying, installation, testing and commissioning response indicator on surface/recess MS box having two LEDs metallic cover complete with all connections etc. as required. (MAKE AGNI AD301MW)

Supplying, installation, testing and commissioning fire alarm sounder mounted in M.S. box (16 SWG) with hinged cover plate complete as required. (MAKE AGNI AD502)

Supplying, installation, testing and commissioning complete as required. 6 Zone FIRE ALARM PANEL

Supplying, laying, testing and commissioning 2Cx1.5 sq.mm ar.cu cable complete as required.

Design, Supply, installation, testing and commissioning of CCTV System as follows: `IP Varifocal Dome camera: Design, Supply, installation, testing and commissioning of 4MP BULLET IP CAMERA.,minimum 1 year warranty Make: Hikvision / Bosch / Pelco / Honeywell / GVD`

Supply , Installation , Testing and commissioning of 16 Channel NVR (Network Vedio Recorder) Make: Hikvision / Bosch / Pelco / Honeywell / GVD

Supply, installation, testing and commissioning of 43` inches LED screen suitable for showing out puts from NVRs on a single screen (24x7) complete in all respect complete as required. Make: Hikvision / Bosch / Pelco / Honeywell / GVD

Supply, laying and termination of CAT6 cable in existing conduits/ raceway/ cable tray for both video and control.

Supply, installation, testing and commissioning of 4 TB Survillance HDD for camera recording.(24*7 ) Make: Hikvision / Bosch / Pelco / Honeywell / GVD

`Supply, installation, testing and commissioning of 8 PORT POE GIGA SWITCH Make: Hikvision / Bosch / Pelco / Honeywell / GVD`

`Supply, installation, testing and commissioning of RJ 45 CONNECTOR Make: Hikvision / Bosch / Pelco / Honeywell / GVD`

Supply, installation, testing and commissioning of Fiber patch cord 1 mtr. complete as required.

Supply, installation, testing and commissioning of Cat -6 Patch cord 2 Mtr. complete as required.

`SITC of 32U (W 600mm/ D 600mm) Floor mount with front glass door and side panels, 4 Fan with lock and key (load bearing capacity of 40Kgs), AC main Channel 12 points 6 Amp (PDU) with Mounting Hardware as per specification etc. all complete Approved Make: Valrack / Netrack / President`

`SITC of Rack Mountable Patch Panel, 24 Cat 6A Loaded Ports, Copper Patch Panel, Straight, Unshielded, Durability (IDC Life) 200 termination cycles with in Built Wire Manager, Grounding Bolt included as per specification etc. all complete Approved Make: Belden / 3C3 / Commscope / Siemon / Legrand `

Supply, Installation, testing and commisioning of Switch 24 ports Cisco Catalyst 1000-24T-4G-L Network Switch, 24 Gigabit Ethernet Ports, 4 1G SFP Uplink Ports, (C1000-24T-4G-L) (MAKE CISCO)

Supply, Installation, testing and commisioning of wireless controller Network Management Device WAN Capable Air-CT2504-5-K9 Wireless Controller (MAKE CISCO)

Supply, Installation, testing and commisioning of Dual Band Wireless Access Point, (MAKE CISCO)

Supply, Installation, testing and commisioning of OI

Supply, Installation, testing and commisioning of Patch Cord

`SITC of Single Face Plate Shuttered, Provision for accepting any Keystone Style RJ45 Outlets, Capable of providing RJ45/ RJ11 type, Label Holders with Plastic covers, Built-in Dust Covers with Back boex as per specification etc. all complete Approved Make: Belden / 3C3 / Commscope / Siemon / Legrand `

Supply, Installation, testing and commisioning of cable manager in rack

`Supply, Installation, testing and Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R407c/R410a/EQUIVALENT Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V plus /-10%, 3Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. - The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5.` 14 HP

`Supply, Installation, testing and Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R407c/R410a/EQUIVALENT Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V plus /-10%, 3Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. - The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5.` 24 HP

`Supply, Installation, testing and Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R407c/R410a/EQUIVALENT Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V plus /-10%, 3Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. - The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5.` 30 HP

`Supply, Installation, testing and Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume aircooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R407c/R410a/EQUIVALENT Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V plus /-10%, 3Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. - The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5.` 32 HP

VRF/VRV 4 WAY CASSETTE INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless/corded remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 DegreeC DB and 19 DegreeC WB temperature. 1.6 TR

VRF/VRV 4 WAY CASSETTE INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless/corded remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 DegreeC DB and 19 DegreeC WB temperature. 2.0 TR

VRF/VRV 4 WAY CASSETTE INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless/corded remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 DegreeC DB and 19 DegreeC WB temperature. 2.6 TR

VRF/VRV 4 WAY CASSETTE INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless/corded remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 DegreeC DB and 19 DegreeC WB temperature. 3.2 TR

VRF/VRV 4 WAY CASSETTE INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration isolation, cordless/corded remote control etc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 DegreeC DB and 19 DegreeC WB temperature. 4.0 TR

VRF/VRV HI-WALL INDOOR UNIT Supply, installation, testing and commissioning of following minimum capacity VRV/VRF Highwall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil ection with DX copper coil, electronic expansion valve, outer cabinet, cordless remote control, drain pan, necessary accessories etc., suitable for operation on 230V±10%, 50Hz, single phase AC supply, complete as required. The unit shall have automatic force shutdown provision in caseof fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature. 1.0 TR

PROPELLER FAN Supply, Installation, testing and Commissioning of following capacities of wall mounted propeller fan of ABS/metal and complete with suitable 1 phase Motor with gravity louver etc. and required for complete installation include Lifting, shifting, assemblling and positioning of the equipment comprising of the following and complete as per specification/drawings and as directed by Engineer In Charge. 100 CFM

PROPELLER FAN Supply, Installation, testing and Commissioning of following capacities of wall mounted propeller fan of ABS/metal and complete with suitable 1 phase Motor with gravity louver etc. and required for complete installation include Lifting, shifting, assemblling and positioning of the equipment comprising of the following and complete as per specification/drawings and as directed by Engineer In Charge. 200/250 CFM

PROPELLER FAN Supply, Installation, testing and Commissioning of following capacities of wall mounted propeller fan of ABS/metal and complete with suitable 1 phase Motor with gravity louver etc. and required for complete installation include Lifting, shifting, assemblling and positioning of the equipment comprising of the following and complete as per specification/drawings and as directed by Engineer In Charge. 400 CFM

PROPELLER FAN Supply, Installation, testing and Commissioning of following capacities of wall mounted propeller fan of ABS/metal and complete with suitable 1 phase Motor with gravity louver etc. and required for complete installation include Lifting, shifting, assemblling and positioning of the equipment comprising of the following and complete as per specification/drawings and as directed by Engineer In Charge. 900 CFM

REFRIGERANT PIPING Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 6.4 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 9.5 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 12.7 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 15.9 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 19 mm dia (OD) (Harddrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 22.2 mm dia (OD) (Softdrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 25.4 mm dia (OD) (Harddrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 28.6 mm dia (OD) (Harddrawn) with tube thickness 1.2 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 31.8 mm dia (OD) (Harddrawn) with tube thickness 1.62 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` 34.9 mm dia (OD) (Harddrawn) with tube thickness 1.62 mm with 19 mm thick insulation

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` Y-Joints (Suction plus Liquid)

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/ hard drawn copper refrigerant piping for DX/VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/ brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required : For exposed piping, UV and Mechanical protection shall be with 6-7 mil minimum thickness and 200 gram/sqmt ±10% interwoven glass fabric. `NOTE: 1) The Copper Piping and Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.` Header Joint

The overall size of table shall be 1500L x 900D x 750H. The worktop shall be made of 25mm thick pre laminate partical boards with E1 norms dully finish with 2mm pvc edge band all the side of worktop. Understructure shall be supported on CRCA MS powder coated angular legs of cross section 40 x 40 x 1.6mm thick and horizontal beam made up of 40 x 20 x 1.2 mm thick. Vertical Legs shall be connected with horizontal beam through aluminium die cast connectors having opening of 40 x 40 on the vertical side and 40 x 20 on the horizontal side to accomodate connection of Leg and horizontal frame. Connector shall be L shaped having angle of 10 degree. Cross beam of section 40 x 20 shall be fixed below the table table ont he horizontal frame using aluminium die cast connector for better strength. Understructure shall powder coated upto 40 to 60microns.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

The overall size of Chair shall be Total height 840 plus /-3 mm, Over all chair width should be 535 plus /-5mm and Overall chair depth should be 535 plus /-5mm. Back Width 360mm at Top and 440mm at bottom, Seat Width 420 plus /-3 mm, Seat Depth 425 plus /-3 mm and Seat height 450mm

`2Seater Bench The overall size of Two seater bench shall be 1250 L x 650D x 830H. Per seat size shall be, Seat - 450 mm in depth, width 550mm, Back width - 540mm, back height- 470 mm.The chair total height shall be measures 830 mm and Seat height shall be measures 485 mm from the floor. It shall be designed ergonomically to provide comfort to the user.The Frame shall be made out of ERW tubes- Cross bar 50 mm diameter with 1.8 mm thickness, seating frame side tube shall be 15mm diameter and 1.8 mm thickness and weld on CRCA perforated sheet of thickness of 1.5mm thick. Side tubes shall be 50mm diameter and 3mm thickness. ERW tubes conforming to IS – 4923. Bench Arm shall have Oval tube shall be fabricated with 48mm length X 20mm width X 1.8mm thickness. ERW tubes conforming to IS – 4923. Frame is welded by CO2 welding process for uniform finish conforming to IS 816. Fabric Upholstery: Seat and back shall be upholstered with fabric. No flaming or progressive smouldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021(match), IS 15061-2002 is optional.Foam: Cushion shall be pre moulded foam of 50 - 55 kg/m3 density in the shape of plywood. Hardness – 22 to 28 kgf at 50% deflection. Ply wood shall be 12 mm thick with 8 to 9 ply. It shall be hot pressed ply - conforming to I S 303. Frame shall be powder coated to provide an attractive finish.The powder coating undergoes 7 step rust resistance pre treatment process viz degreasing, pickling as per IS standard. After pre treatment process, the components shall NANO coated and passified for better adhesion of paint as per IS 3618 - 2016. The pacified components shall be powder coated with epoxy polyester powder to the thickness of 50-80 microns as per IS 101 and oven baked at 180 degrees for getting the scratch resistance finish. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.`

`3-Seater Bench The overall size of Thee seater bench shall be 1800 L x 650D x 830H. Per seat size shall be, Seat - 450 mm in depth, width 550mm, Back width - 540mm, back height- 470 mm.The chair total height shall be measures 830 mm and Seat height shall be measures 485 mm from the floor. It shall be designed ergonomically to provide comfort to the user.The Frame shall be made out of ERW tubes- Cross bar 50 mm diameter with 1.8 mm thickness, seating frame side tube shall be 15mm diameter and 1.8 mm thickness and weld on CRCA perforated sheet of thickness of 1.5mm thick. Side tubes shall be 50mm diameter and 3mm thickness. ERW tubes conforming to IS – 4923. Bench Arm shall have Oval tube shall be fabricated with 48mm length X 20mm width X 1.8mm thickness. ERW tubes conforming to IS – 4923. Frame is welded by CO2 welding process for uniform finish conforming to IS 816. Fabric Upholstery: Seat and back shall be upholstered with fabric. No flaming or progressive smouldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021(match), IS 15061-2002 is optional.Foam: Cushion shall be pre moulded foam of 50 - 55 kg/m3 density in the shape of plywood. Hardness – 22 to 28 kgf at 50% deflection. Ply wood shall be 12 mm thick with 8 to 9 ply. It shall be hot pressed ply - conforming to I S 303. Frame shall be powder coated to provide an attractive finish.The powder coating undergoes 7 step rust resistance pre treatment process viz degreasing, pickling as per IS standard. After pre treatment process, the components shall NANO coated and passified for better adhesion of paint as per IS 3618 - 2016. The pacified components shall be powder coated with epoxy polyester powder to the thickness of 50-80 microns as per IS 101 and oven baked at 180 degrees for getting the scratch resistance finish.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.`

overall Size of Rack shall be size of - 760 L x 430-100 D x 1000 H, The Rack shall be made up of 18mm thick Pre-laminate particle board E1 norms duly finshall hed with 2mm pvc edge banding on automatic machine.Rack shall have 7 particular shelf for storage.It shall come with size of 760mm Length with bottom depth shall be 430mm but at top 100mm depth. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

The overall size of Book rack shall be 1200L x 450D x 1050H. The side body shall be made of 18mm thick pre laminate partical board with 2mm pvc edge band all the side. The back shall be made of 9mm thick pre laminate partical board with E1 norms and 2mm pvc edge band finished. The rack shall have multiples compartment for keeping books,magzie and other items. The rack shall have 50mm skriting at the bottom. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

The overall size of Book rack shall be 1500L x 450D x 1800H. The side body shall be made of 18mm thick pre laminate partical board with 2mm pvc edge band all the side. The back shall be made of 9mm thick pre laminate partical board with E1 norms and 2mm pvc edge band finished. The rack shall have multiples compartment for keeping books,magzie and other items. The rack shall have 50mm skriting at the bottom.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

The overall size of Book rack shall be 1200L x 450D x 1800H. The side body shall be made of 18mm thick pre laminate partical board with 2mm pvc edge band all the side. The back shall be made of 9mm thick pre laminate partical board with E1 norms and 2mm pvc edge band finished. The rack shall have multiples compartment for keeping books,magzie and other items. The rack shall have 50mm skriting at the bottom. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Overall Size : 900 x 450 x 1830. The body shall be made of 18 MM Thick prelam particle board with 2 MM PVC Edge banding finish. Each shelf shall be of retractable type meant for display of product as well as act as shutter to be retracted for use of magazines storage behind. The sliding mechanism shall be made up of press formed metal sheet and shelf handle should be laser cut metal sheet.The inner space of each shelf is designed to keep a standard magazines or books. The shelf should be made up of of 18 mm thick prelam particle board with PVC Edge banding finish. All metal parts shall be powder coated with 60-80 micron thick powder coating finish. Construction of the product should be knock down design. The OEM should have BIFMA Level certification, ISO 9001, 14001, 18001,Green Guard, IGBC Gold certified manufacturing plant

` Doble Sided Book Rack starter : The overall size of the book rack shall be 900 L X 700 D X 1950 (LDH)mm. Uprights shall be made up of - MS Pole 40 x 40 x 1.6 Tube having slot single side, size of 25 x 5mm rctangular slot to support the partition bracket having overall size of 300 x 99mm. Two U channel shall be welded with MS square pole size of 13 x 10 x 13 and have 1mm thick for support of back panel. Shelves should be made of MS powder coated metal 1.2mm, supported with hat shaped brackets size of 9 x 10 x 20 x 10 x 9mm and overall size of 36 x 10mm. Back Panel shall be made up of MS Powder coted metal 0.8mm. Top panel, Side Panel and Bottom Panle shall be made up of 18mm thick PLT. Skriting shall be provided of size of 900 x 40mm. Tolerance of plus /- 5mm to be considered for product sizes i.e Length, Depth and height and tolerance of 5% to be considered in pipe thickness and Pipe sizes.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

Doble Sided Book Rack add on : The overall size of the book rack shall be 900 L X 700 D X 1950 (LDH)mm. Uprights shall be made up of - MS Pole 40 x 40 x 1.6 Tube having slot single side, size of 25 x 5mm rctangular slot to support the partition bracket having overall size of 300 x 99mm. Two U channel shall be welded with MS square pole size of 13 x 10 x 13 and have 1mm thick for support of back panel. Shelves should be made of MS powder coated metal 1.2mm, supported with hat shaped brackets size of 9 x 10 x 20 x 10 x 9mm and overall size of 36 x 10mm. Back Panel shall be made up of MS Powder coted metal 0.8mm. Top panel, Side Panel and Bottom Panle shall be made up of 18mm thick PLT. Skriting shall be provided of size of 900 x 40mm. Tolerance of plus /- 5mm to be considered for product sizes i.e Length, Depth and height and tolerance of 5% to be considered in pipe thickness and Pipe sizes.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

`The overall size of table shall be 1500L x 600D x 750H. The worktop shall be made of 25mm thick pre laminate partical boards with E1 norms dully finish with 2mm pvc edge band all the side of worktop.Modesty shall be made of 18mm thick pre laminate partical boards with E1 norms with 2mm pvc edge band all the visible side and connected with 2 nos L-shape pressure aluminium die casted connector. The height of the modesty shall be 450mm. The understructure will feature vertical legs made of 50 mm x 50 mm x 1.6 mm steel tubing, while the horizontal frame will be constructed from 50 mm x 25 mm x 1.6 mm steel. A cross beam, sized 40 mm x 20 mm x 1.6 mm across the length of the table, will be installed beneath the tabletop to provide additional support. This cross beam shall be connected on both sides with pressure die cast connectors of 50 mm height, 70 mm width and 35 mm depth designed in a shape acting as spacer between horizontal frame and worksurface. Mobile Drawer Unit : It shall be of size of 400 x 450 x 600 (WDH) mm made up of 18mm thick Pre-laminate particle board as per E1 norms and its edges duly sealed with 2mm PVC Lipping on automatic machine at visible sides. Drawer front and sides shall be made up of 18mm, back 9 mm thick pre laminated particle board of E1 grade with visible edges sealed with 2mm PVC edge band. The drawer side surface shall be provided with finger groove handle-less design. Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface and 12 mm tapered towards inside at 45 degree and then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock shall be provided. Tolerance of plus /- 5mm to be considered for product sizes i.e Length, Depth and height and tolerance of 5% to be considered in pipe thickness and Pipe sizes.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

` Overall dimension-1880 mm Length X 610 mm W X 810 mm. It should have two section moulded mattress top. Backrest should be adjustable through rachet. Handle shall be made up of Stainless steel to lift backrest. Mattress Foam should be Moulded and thickness should be 2.5 inch. Examination couch should have four vertical leg size of 30 X 30 mm square CRC pipe of 1.6 mm thickness. BP appratus tray rotatable should be provided that can go under examination couch top. It should be made of 16 G top frame of 20 X 40 MM rectangular CRCA pipe.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

Circular Puffe of size 600 W x 600 D x 450 H. specifications: Seating: Fabric shall be used as upholstery with SF fabric, Polyester and Viscose - 300 GSM, Abrasion- ) 45000 cycles. No flaming or progressive smouldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021(match), IS 15061-2002 is optional. Foam: Cushion with pre moulded foam of 50 kg/m3 density in the shape of Cylinder shall be used with Hardness – 30 ± 3 kgf at 50% deflection. Frame : Upholstery shall be done with MS frame welded in CO2 welding process for uniform finish conforming to IS 816. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Overall size of table shall be of size 1200 L x 800D x 750 H (mm). The worksurface of the table shall be made up of 18mm thick Prelam hydroshield top water resistant. Understructure shall be supported on CRCA MS powder coated angular legs of cross section 40 x 40 x 1.6mm thick and horizontal beam made up of 40 x 20 x 1.2 mm thick. Vertical Legs shall be connected with horizontal beam through aluminium die cast connectors having opening of 40 x 40 on the vertical side and 40 x 20 on the horizontal side to accomodate connection of Leg and horizontal frame. Connector shall be L shaped having angle of 10 degree. Cross beam of section 40 x 20 shall be fixed below the table table ont he horizontal frame using aluminium die cast connector for better strength. Understructure shall powder coated upto 40 to 60microns. Tolerance of plus /- 5mm to be considered for dimensions Length, Depth and height and tolerance of 5% to be considered in thickness.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Supplying and placing cafe table with an overall size 900 X 900 X 750. The top of the table shall be made 18mm thick PrelamHydroshield Top. The profile shall be in square shape. The top shall be supported on MS powder coated 2mm thick sheet. The table under structure shall be made up of SS grade 202 base pole leg having size 60mm X 60mm with 1.2mm thick. The base plate shall be SS 202 grade base having size 460mm X 460mm. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

The chair shall be made from a single-piece injection- molded polypropylene material with a half-round back contour to offer enhanced comfort and support. The overall width of the chair shall be 500 mm, depth 530 mm, and height 800 mm. The seat height from the floor shall range from 435 mm, and the back height from the seat shall be 400 mm. The backrest will feature a half- round contour, with a lumbar width from end to end at lumbar level shall be at least 450 mm and a top width of 430 mm. The front of the seat will include a waterfall edge with a minimum height of 25 mm. The seat width, measured from the center, shall be 440 mm, with a depth of 400 mm. The backrest will be perforated with a triangular pattern for ventilation and flexibility. Ribs beneath the seat, extending from front to back, will have a minimum height of 12 mm to enhance stability. The thickness of the chair at the various polypropylene edges shall range from 7 mm, 8mm, 9mm respectively. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Reception table : The overall size of the reception table shall be 2400 mm length, 750 mm depth and 1050 mm height. On the front side both ends shall be provided with groove design strips to enhance the overall look. At the centre of the front side L shape surface shall be provided fixed up with hinges to paste logo of the University. The entire table shall be made up of 25mm / 18mm thick pre laminated particle board of E1 norms. Inside of table a working height shelf should be provided or height 750 mm to keep desktop/ laptop and normal working with sitting. the edges of the visible surface shall be sealed with 2mm thick PVC lipping on automatic machine. Unless specified tolerance of plus /- 5mm to be considered for product dimensions Length, Depth and height and tolerance of 5% to be considered in thickness and size of material and components used.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

The overall size of Chair shall be height 1020 to 1120 plus /-5 mm, width should be 595 plus /-5mm and depth should be 640 plus /-5mm. Back Width 435 mm at Top and 490mm at bottom, Seat Width 500 plus /-5 mm, Seat Depth 465 plus /-5 mm and Seat height 450mm to 550 mm plus /-5mm range. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25 plus 3kgf at 50% deflection conforming to IS 3400. Seat shall be upholstered with micro fabric 100% polyster 180 GSM abrasion ) 50000 cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Mesh at the back rest. The back frame shall be made up of injection molded nylon GF 3. Adjustable Lumbar Support of size 300 mm lenght, 150 mm height and 3mm thickness travel upto 65mm. The Chair should be provided with Snchyro mechanism with single lever with one position lock. The mechanism shall allow360 degree revolving feature along with height adjustablility one Way with height adjustment button made of Delrin P 500 and arm top shall be PU material. The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Nylon Base to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. The base shall be 660 mm PCD (26 inches) five pronged bases made up of PA6, 30% glass filled reinforced with bottom ribbing for additional buttress and strength. Tolerance of plus /- 5mm to be considered for product sizes i.e Length, Depth and height and tolerance of 5% to be considered in pipe thickness and Pipe sizes.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

`STORAGE RACK SIZE:1800LX300DX1775H The horizontals and Verticals of the frame structure shall be made from Aluminium extrusions of 6063 grade alumalloy, confirming to DIN ISO -2768-1 and connected each other by high pressure aluminum diecast connectors using counter sunk screws to ensure stability, high strength and safety. Aluminium profiles shall be used to fix the racks made up of 20x20Sq.mm profile, sledge profile for 18.0mm thk shelf panel, sledge profile for 5.0mm thk glass panel and sledge profile with two opposite sides to fix 18.0mm thk panels on two sides parallelly. The connectors used shall be 02-way, 03-way (2D), 03-way (3D), 04-way and 05-way as required. All the connectors shall be pressure diecast connectors in ADC-12 material confirming to ASTM E 1251-2011, IS 7658- 1990 and IS 11035 – 1190 for chemical composition and IS 1608 – 2005 for UTS and Ys. All connectors shall be provided with M5 threads to fix M5x0.8P CSK screw. The wooden planks used for shelves, back panels and planter box shall be made up of 18mm thk prelam particle board on both sides (PLT) with edge banding finish. Length and width / depth of these planks shall be based on product size and design. Each such shelf should be able to take weight upto 15.0Kgs UDL. Height of Planter box shall be 120mm H, out of which about 19mm shall fit in the frame work. Visible height of planter box shall be about 100 mm. Glass used shall be of 5mm thk clear float glass. The leg height from ground shall be 75mm, each leg shall be fitted with a leg bush injection moulded part in tough engineering plastic material, ABS. Aluminium extrusions and Diecast connectors shall be black matt powder coating finish and the wooden shelves are offered with both side lamination in Thanasu Maple or Everest white.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

The overall size of the 1 seater sofa shall be 850 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the combination of treated pine wood of 20 -25mm thick and neem based plywood sheets. The polyurethane (PU) foam of density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the webbing belts. Seat height should be 440mm ( plus /- 10mm) and seat depth shall be 525mm ( plus /- 20mm). Each sofa individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process that shall be environment friendly to enable powder coating to the thickness of 50- 80 microns. The fabric used shall be 450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

The overall size of the 3 seater sofa shall be 2050 L x 790 D x 790 H. Sofa inner frame structure shall be made mainly from the combination of treated pine wood of 20 -25mm thick and neem based plywood sheets. The polyurethane (PU) foam of density 32 and 40 shall be used in seat constructions and 32 density foam used in back construction along with the webbing belts. Seat height should be 440mm ( plus /- 10mm) and seat depth shall be 525mm ( plus /- 20mm). Each sofa individual set type shall consist of 4 metal legs of 200 mm height that shall be laser cut and press formed in 2mm thick CR steel in complaince with IS 513: 2008. The legs shall be formed in V-shape with 125 x 125mm length flanges on its top face and moulded leg bush shall be fixed at its bottom that shall support height adjustment of upto 10mm. To suppor thte sofa two nos wide flanges of the leg shall be be provided. Legs shall be pretreated through nano ceramic process that shall be environment friendly to enable powder coating to the thickness of 50- 80 microns. The fabric used shall be 450-475 gms per meter having abrasion resistance of more than 50K rubs high quality polyester fabric. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

`Centre table Size The overall size of the Centre table shall be 1050 mm Length x 550 mm depth, 450 mm height. the table top shall be made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion surface shall be provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: Table top shall be supported on CRCA legs duly powder coated. The understructure should be provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom. The edges of the table top shall be rounded and edges shall not be sharp. The legs shall be in angular design and thicker on the top and thinner on the boattom side. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

` The overall size of the Centre table shall be dia 600mm, 450 mm height. the table top shall be made up of 18mm thick prelaminated particle board of approved shade All the edges of discussion surface shall be provided with machine pressed 2mm thick PVC lipping glued with hotmelt Eva glue free from any VOC. Under Structure Support: Table top shall be supported on CRCA legs duly powder coated. The table understructure should be provided with 32mm by 1.6mm thickenss swaged tube from 32mm top and 19mm bottom. The edges of the table top shall be rounded and edges shall not be sharp. The legs shall be in angular design and thicker on the top and thinner on the bottom side.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

`Diameter 2800mm Approx 08 seater Round Sofa The circular modular sofa shall be crafted with an inner frame made from a combination of treated solid wood, such as Neem or Pine wood, and plywood. This robust construction shall be reinforced with high-quality webbing belts, ensuring strength, rigidity, and stability for long-lasting durability. The seat cushions shall be made of 40 density polyurethane (PU) foam, while the backrest cushions shall be 32 density PU foam, offering a balance of firm and comfortable support. The seat-to- backrest angle shall be ergonomically designed to provide optimal seating comfort. The seat height shall be between 16 to 18 inches, and the depth shall be between 18 to 22 inches, making it suitable for a wide range of users. The sofa shall be elevated approximately 3 inches off the ground using metal legs that are powder-coated for added durability, creating a floating look and allowing for easy cleaning underneath. The upholstery fabric shall be of premium quality, with a weight of 450 grams per linear meter (glm). It shall have an abrasion resistance of over 50,000 rubs, ensuring it withstands regular use, and excellent color fastness to light, rated better than 5, and to rubbing, rated between 4-5. The fabric shall be made from high-quality polyester, providing a soft, comfortable feel while being durable. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

`4 Door Locker Cabinets for Library Overall Size : 380 x 450 x 1850 (WDH)mm. Manufacturing and supplying of 4 door Locker Unit made of 100% virgin Epoxy Powder Coated CRCA confirming to shall : 513 CR2 (Cold Reduced Carbon Steel Sheets and Strips (Part 1), 2016. Complete material should passes through 7 stage, based Pre- treatment plant prior to powder coating, making it highly corrosive resshall tant. Construction shall be welded from complete 0.6 mm thick CRCA sheet. Each Compartment Shelf shall have uniformly dshall tributed load capacity per shelf shall 35 kg. Cam lock shall be provided with recessed handle. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

`Recreational Area Steel Benches 3 seater Overall size of the metal bench should be 1200mm L x 400mm D x 450mm H within tolerance of plus /-5mm ensuring proper levelling of the bench. The bench should be bent with single stroke radius bending tool to get the inner radius of R75 and outer bending radius of R85mm without any undulations. There should be a gap of 69mm( plus /-5mm) between the LH side of the bench to the immediate slot and same 69mm( plus /-5mm) gap should be left from RH side also to ensure not to have any deformation or drag in the slots while bending. The Metal Bench shall made from a 10mm thick Hot rolled pickled and oiled sheet with minimum 200 no`s of square slots on the top. All through and through straight slots with maximum slot size of 12mmx12mm, with a min gap between slots of 15mm. The gap between the front edge to the front line slots and rear edge to the rear line slots of the bench should be 45.50mm on each side. The Metal bench should be pretreated to ensure proper adhesion with the top coating. The metal bench should finished by best quality powder with coating thickness of 40-60 microns.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

`The overall size shall be of Cabin Table 1500W X 750D X 750H, Side unit of 900W X 450D X 750H. The worktop shall be made up of 25mm thick PLPB E1 norms duly finished with 2mm pvc edge band. The Modesty shall be made of 18mm thick pre laminated partical boards with E1 norms and all visible side 2mm pvc edge bending. Modesty shall be connected with 3 nos L-shape pressure aluminium die casted connector. MOdesty height shall be 450mm .The understructure shall be made of 18mm thick prelam partical board with 2mm pvc edge band all the visible side.Wire Management: 350 mm Anodised flip up Made of Aluminum in anodised finish, that shall have soft closure and three way wire acess and PVC cable tray. For entry of cables from the floor into the cable tray, Wire Entry. Side storage of size 900 x 450 x 750 H to be provided made up of 18mm thick PLPB E1 norms composite having two drawer and filling units/ shutters. back panel made up of 9mm thickn PLPB E1 norms. Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface and 12 mm tapered towards inside at 45 degree and then sealed with minimum 2mm thick PVC lipping on automatic machine. Suitable lock shall be provided. The back unit shall be size of 1500L x 450D x 750H. Top shall be made up of 18mm thick pre laminated particle board E1 norms and Back shall be made up of 9 mm thick pre laminated particle board with 2mm PVC edge lipping, Shutters shall be made up of 18 mm thick pre laminated particle board. Shutters to be provied for compartment. The back unit shall be consist of open and close compartment.he hinged doors top shall be provided with finger groove handle-less design for a streamlined look. Finger groove shall be created by providing a reverse tapered profile edge of 6mm straight surface and 12 mm tapered towards inside @ 45 degree and then sealed with minimum 2mm thick PVC lipping on automatic machine. Cam Lock faciltity should be provided for safe storage of documents.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.`

The overall size of Chair shall be : width 600 plus /-5mm, depth 640 plus /-5mm. Total height 1170 to 1270 plus /-5 mm, Back Width 425 mm at Top and 500mm at bottom, Seat Width 500 plus /-5 mm, Seat Depth 470 plus /-5 mm and Seat height 470mm to 570 mm plus /-5mm range. Seat made up of foam pre moulded at 55 kg/m3 density. hardness of 25 plus 3kgf at 50% deflection conforming to IS 3400. Seat shall be made up of foam pre moulded at 55 kg/m3 density. hardness of 25 plus 3kgf at 50% deflection conforming to IS 3400. Seat shall be uplhostered with micro fabric 100% polyster 180 GSM abrasion ) 50000 cycles. Fire rated fabric confirming to BS EN 1021 (match) should be used. The chair shall be supplied with Mesh Back rest. The back frame shall be made up of Injection molded PPGF 20% in light grey shade, armest support also in light grey shade. PPGF Frame thickness shall be minimum 4.8mm. Adjustable Lumbar Support made up of PU having size 365 mm x 110 mm x 25mm thick shall be provided for better comfort. Lumbar Support material Integrated one-piece Molded PU. The Chair should be provided with Self Calibrating Multilock Mechanism (Bio Snchyro mechansim) that should adjust the tension of the back sensing weight of the user. The mechanism shall allow 360 degree revolving feature along with height adjustablility. One Way Adjustable Arms (Height) to be provied with height adjustment button of size 73mm x 18mm made of Delrin P 500. Armrest Height shall be 170mm to 260mm adjustable from Seat The mechansim shall possess seat to back recline ratio of 3:7. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Metal base shall be provided of light grey color matching the chair back and armrest.The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of plus /- 5mm to be considered for product sizes i.e Length, Depth and height and tolerance of 5% to be considered in pipe thickness and Pipe sizes..The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.

` The overall size of Chair shall be height 870 to 970 plus /-5 mm, Back Width 415 mm at Top and 470mm at bottom, and 450mm at the lumber support. Seat Width 480 plus /-5 mm, Seat Depth 440 plus /-5 mm and Seat height 420mm to 520 mm plus /-5mm range. over all chair width should be 540 plus /-5mm and Overall chair depth should be 610 plus /-5mm. Seat should be made up of foam pre moulded at 55 kg/m3 density. hardness of 25 plus 3kgf at 50% deflection conforming to IS 3400. Seat shall be upholstered with micro fabric 100% polyster 180 GSM abrasion ) 50000 cycles. No flamming or progressive smoldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021 (match) should be used. The back frame shall be made up of PPGF and the injection molded in grey color, armrest also in grey color. The chair shall be supplied with Mesh Back rest. The Chair should be provided with center tilt two position lock Mechanism.The mecahinsm plate shall be attached to seat with 2.5mm thick plate. The mechanism shall allow 360 degree revolving feature along with height adjustablility. Fixed arms connected to seat and back in the same contour.Armrest shall be Single peice die casted trapezium shaped arm rest overall size of 280 L x 230 H x 11mm thick at user side. The mechansim shall possess seat to back recline ratio of 1:1. The Gas Lift used shall be class 4 tested as per ANSI BIFMA standards. Metal Base in grey color to be provied. Twin castors 50 mm dia with PA6 material complying to ANSI/ BIFMA X 5.1 2017 standards. the axle pin shall be rust protected zinc passivated. The base shall be made up of mild steel powder coated in grey shade to match the entire grey theme of chair.Metal base powder coated made up of sheet thickness 2mm.Tolerance of plus /- 5mm to be considered for product sizes i.e Length, Depth and height and tolerance of 5% to be considered in pipe thickness and Pipe sizes. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.`

The overall size of back to back sofa shall be 1800L x 1350D x 775H. Both side of sofa shall be provide end table with size of 300mm length with 675mm depth. The end table shall be made of 18mm thick prlam partical board with 2mm pvc edge band all the side. The seating height that is under-structure with sofa cushions shall be 450mm. The sofa shall be designed with sleeker and tapered arm rests and back top. The sofa structure shall be made up of wooden structure made from treated and seasoned solid wood and plywood fixed with the combinations of 32 and 40 density PU foams for seat and back rest, upholstered with polyester fabric of 450 glm, having abrasion resistance more than 50K rubs, colour fastness to light better than 5, colour fastness to rubbing 4-5. The Under-structure shall be a distinctive 3D design, made from laser cut metal roll formed steel with Overall size of 575mm L x 192mm D x 260mm H made in the close tolerance of plus /- 3mm. Leg top beam shall be made up of 40x20x1.60mm thick rectangular profile tube, the vertical legs shall be tapered square to round tube profiles with Sq.30mm at top gradually tapered to get round diameter of 19mm ( plus /-2mm) at the bottom. The bottom portion of the dia 19 shall be formed to make it perpendicular to the floor / ground. Each leg shall be fixed with M8 hex bolt insert moulded nylon leveller of diameter 40mm and with an option to adjust the leg height upto 15mm based on floor undulation. The leg to leg shall be connected using cross beams of 40x20x1.60mm thk rectangular ERW CR tubes. All metal parts come with Powder Coating Finish of 50–80micron thk.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Overall size of the table shall be be of size 1030 L x 500D x 750 H (mm). The table top shall be in Trapezoidal shape and it shall be from 25mm thk E1 prelam particle board with 2mm PVC edge banding. Uniqueness of thshall be table shall be that, Two legs comes with Castors and Two leg with leg bush fitted with adjustable levellers. Each Leg shall be from Round MS Tube structure of size 44.40 x 1.60mm thk (16g) confirming to shall be 4923 : 1997, fixed with high pressure aluminum die cast connector at the top, which shall be from ADC-12 material confirming to ASTM E 1251-2011, shall be 7658-1990 and shall be 11035 – 1190. For chemical composition and shall be 1608 – 2005 for UTS and Ys.. All 04 legs are fixed with these diecast connectors and the connector to connector are joined by the cross beams of Square shape hollow profiles of 25x25mm, using reverse taper mechanshallm. Two legs at one end of the table are fitted with Leg bush and adjustable leveller which shall be an injection moulded in engineering plastic and other two legs are fixed with Castor wheels. Product come shall be knockdown Construction, easy to assemble, sturdy and stable product.All metal and diecast parts comes with powder coating finshallh of 60-80 microns thick. All hardware are of steel 8.8 grade comes with zinc blue / yellow / black passivation. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2 certification, India Design Mark and Green Guard (UL) Certification from valid source.

`Overall Size of puoffy shall be 650 x 750D x 725mm H. Size of Pouffy shall be Dia 500 x 500 H including Castors. Writing Table shall be madeup of 18mm Hydrosheild material with reverse waterfall edge and its all edges should be grinded and polshall hed. The table shall be supported by metal press formed steel bracket. The table can be used either as writing desk or also as back support. All metal parts shall be black powder coated at 40-60 microns. Seating: Fabric shall be used as upholstery with fabric, Polyester and Vshall cose - 300 GSM, Abrasion- ) 45000 cycles. No flaming or progressive smouldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021(match), shall 15061-2002 shall optional. Foam: Cushion with pre moulded foam of 50 kg/m3 density in the shape of Cylinder shall be used with Hardness – 30 ± 3 kgf at 50% deflection. Frame : Upholstery shall be done with MS frame welded in CO2 welding process for uniform finshall h conforming to shall 816. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2 certification, India Design Mark and Green Guard (UL) Certification from valid source. `

The overall size of reading table shall be 1200L x 600D x 750H. The worktop shall be made of 25mm thick pre laminate partical boards with E1 norms dully finish with 2mm pvc edge band all the side of worktop. The understructure will feature vertical legs made of 50 mm x 50 mm x 1.6 mm steel tubing, while the horizontal frame will be constructed from 50 mm x 25 mm x 1.6 mm steel. A cross beam, sized 40 mm x 20 mm x 1.6 mm across the length of the table, will be installed beneath the tabletop to provide additional support. This cross beam shall be connected on both sides with pressure die cast connectors of 50 mm height, 70 mm width and 35 mm depth designed in a shape acting as spacer between horizontal frame and worksurface. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.

Overall size of Discussion table shall be of size Dia.1200 x 750 H (mm). The worksurface of the table shall be made up of 25mm thick Prelam hydroshield top water resistant. The main tables shall be supported by special design legs. The legs at the visitor’s side shall be 90° and other side shall be 110°. The legs shall be Dia 44mm ERW Tube confirming to IS 4923 : 1997 – 16g. Main leg members shall be connected through a horizontal member size 1.6mm thk, 50x25 cold formed ERW tube by the aluminium die casted connector which having opening of 44mm dia on vertical side and 50 x 25 on the horizontal side to accommodate connection of Leg and horizontal frame.The legs shall have clear and tough polycarbonate leg bush and swivel type levelers to cater for floor undulations ± 20 mm. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2 certification, India Design Mark and Green Guard (UL) Certification from valid source.

The overall size of reading table shall be 1200L x 600D x 750H. The worktop shall be made of 25mm thick pre laminate partical boards with E1 norms dully finish with 2mm pvc edge band all the side of worktop. The understructure will feature vertical legs made of 50 mm x 50 mm x 1.6 mm steel tubing, while the horizontal frame will be constructed from 50 mm x 25 mm x 1.6 mm steel. A cross beam, sized 40 mm x 20 mm x 1.6 mm across the length of the table, will be installed beneath the tabletop to provide additional support. This cross beam shall be connected on both sides with pressure die cast connectors of 50 mm height, 70 mm width and 35 mm depth designed in a shape acting as spacer between horizontal frame and worksurface.Wire Management: The Raceways shall provided below the work surface for carrying wires from one end to other end of the cluster, Size offered shall be 250mm Ht, Thickness 70mm. With vertical wire entry cover and 65mm dia grommet hole for wire access. The raceway shall be made of 0.8mm CRCA with duly powder coated. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.

Overall size of table shall be of size 1500 L x 600D x 750 H (mm). The worksurface of the table shall be made up of 18mm thick Prelam partical board with 2mm pvc edge band all the visible side. The understructure will feature vertical legs made of 50 mm x 50 mm x 1.6 mm steel tubing, while the horizontal frame will be constructed from 50 mm x 25 mm x 1.6 mm steel. A cross beam, sized 40 mm x 20 mm x 1.6 mm across the length of the table, will be installed beneath the tabletop to provide additional support. This cross beam shall be connected on both sides with pressure die cast connectors of 50 mm height, 70 mm width and 35 mm depth designed in a shape acting as spacer between horizontal frame and worksurface.The Intermediate screen shall be provided of size 525 mm L x 350 mm ht. made up of 6 mm thick clear acrylic, having aluminum extrusion at all three sides having cross section size of 12mm x 5mm and joined at all 4 corners with Zinc mazak5 die cast connector of size 15 L x 15 H x 12mm W.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.

The chair shall have minimum overall dimensions of 490 mm in width, 480 mm in depth, and 800 mm in height. The seat and backrest shall be made from a single piece of injection-molded PPGF 20% material. The seat width will be 450 mm near the back and 390 mm at the front, creating a tapered appearance, with a waterfall edge at the front. The seat depth shall be 390 mm, and the junction between the seat and back shall feature a radius to provide enhanced lumbar support. The backrest will have a width of 450 mm near the seat and 360 mm at the top, with a minimum height of 360 mm from the seat. The thickness of the seat and back shell shall be 8 mm ± 0.25 mm. The understructure will consist of loop legs made from 12 mm thick mild steel (MS) rods, conforming to IS 7887 standards. The loop legs shall be interconnected by an MS bar plate (25 mm x 5 mm), located beneath the chair shell. Each bar plate will be equipped with holes for securely attaching the chair shell to the understructure. Injection-molded polycarbonate leg shoes will be fitted to the understructure to provide additional stability and protect the floor surface. The seat assembly will feature silicone bushings to ensure smooth, scratch-free stacking. The entire understructure will be powder-coated, with a finish thickness of 40 to 60 microns, ensuring long- lasting durability and a high-quality appearance.

`Curve Book library and sofa size - 1950 L x 775 D x 750 H The curve Library shall be made up of 18mm thick Pre- laminate particle board E1 norms duly finished with 2mm pvc edge banding on automatic machine and all the structure should be fixed by mini fix and dowels. Every curver library shall have 4 compartment with the height of 340mm with 300mm depth and the outer curved carrier 3900mm Dia with inner curved seating area) carrier 1950mm Dia. seating height shall be 450mm with cusion thickness 110mm. Seat shall be upholstered with SF fabric, Polyester and Viscose - 300 GSM, Abrasion- ) 45000 cycles. No flaming or progressive smouldering within one hour of placement of the cigarettes. Fire rated fabric confirming to BS EN 1021(match. Foam: Cushion with pre moulded foam of 50 kg/m3 density in the shape of Cube. Hardness – 30 ± 3 kgf at 50% deflection. Frame : Upholstery done with 19mm round MS frame welded in CO2 welding process for uniform finish conforming to IS 816.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.`

`NOMAD with Storage 1560L X 500D X 1800H NoMad is a movable writing board that comes with magnetic writing/marker board on one side and with a option to mount monitor on other side with inbuilt wiring. Size of the marker board is 1200x900mm. (Incase of 1560L x 1800H, the marker board size comes to 1500L x 900H) Product has storage underneath marker board size of 1500 x 300 x 300mm (LWD) that is made from 18mm Prelam particle board with edge binding, comes with shutters on either ends and a open shelf at centre, provision to keep Marker Pens/Duster / TV remote etc. The vertical poles of NoMad are from Spl. profile MS tube size of 75 x 30 x 1.6mm thick, Feet are high pressure aluminium diecast having multiples of ribs to provide strength to base parts fitted with best quality castors of Dia 60mm. 02 metal hooks are offered with a pole to keep wires in place when not in use. NoMad comes with 02 HDMI and a 3 mtr length 3 core wire, a power doc fixed on top of storage has 2 sockets, 1 switch and 2 USB. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark. All Metal and Diecast parts comes with powder coating finish. All Plastics are in TML grey colour. The design of the product is modular, easy to assemble, easy to move.`

The overall size of Board room table shall be 3600L x 2100D x 750H. The main table shall be provided on one side of the table with size of 2100L x 600D x 750H. The two addon table shall be provided on both side with size of 1500L x 600D x 750H. The worktop shall be made of 25mm thick pre laminate partical boards with E1 norms dully finish with 2mm pvc edge band all the side of worktop. Modesty Panel shall be made up of 18mm thick 600mm ht plt modesty panel should be considered. It shall be provided with machine pressed 2mm thick imported PVC lipping glued with hotmelt Eva glue free from any VOC. The understructure will feature vertical legs made of 50 mm x 50 mm x 1.6 mm steel tubing, while the horizontal frame will be constructed from 50 mm x 25 mm x 1.6 mm steel. A cross beam, sized 40 mm x 20 mm x 1.6 mm across the length of the table, will be installed beneath the tabletop to provide additional support. This cross beam shall be connected on both sides with pressure die cast connectors of 50 mm height, 70 mm width and 35 mm depth designed in a shape acting as spacer between horizontal frame and worksurface. The Intermediate leg: Two Verticals of Intermediate leg will have to be with 60x40mm rectangular ERW tubes and both legs are joined using a beam section of 40x40x1.6mm thk at the top side. The 60x40 verticals to have through “U” notch or through cut out of 40x41mm size at the top side to locate 40x40 cross beam. Understructure shall powder coated upto 40 to 60microns.Wire Management: The Raceways shall provided below the work surface for carrying wires from one end to other end of the table, Size offered shall be 125mm Ht, Thickness 50mm. With vertical wire entry cover. The raceway shall be made of 0.8mm CRCA with duly powder coated.450 mm Anodised flip up Made of Aluminum in anodised finish, that shall have soft closure and three way wire acess and PVC cable tray. Per table one 450 mm flip up and cable tray shall be provided for easy wire access.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark.

Providing and placing of Slotted Angle Racks of Overall Size shall be 1800 mm (H) x 900mm (W) x Depth 450 mm(D). Each rack shall be provided with 5 panels for loading having 100kgs Load carrying capacity (Uniformly Distributed Load) per panel. Open type Rack system consists of Angle, Decking Panel, Corner plate, Nuts and Bolts. Angles : Material of Angles is as per IS 10748. The thickness of the angles when made from sheet steel shall be 1.6 mm. Angles shall be of rolled formed construction and free from twist, sharp edges and burrs. Angles shall have holes provided at a pitch of 19.05mm. Size of the Angles should be 35mm x 35mm x 1.6 mm(Thick). Panels : Material of panels is as per IS 10748 / IS5986- Fe 410. Panels shall be 6 bend panels and shall be made from mild steel sheets not less than 0.8 mm in thickness with lipped flanges. Width of flange being 31mm and depth of lip 17mm. The panels shall have 9mm holes for corner plates. Size of the Panels is 905 W x 371 D x 0.8 mm thick. Will have 6 bends and get bolted to the Angles at each of the four corners according to Minimum of 100 Kg load per level. Corner Plates (Gussets): Material of corner plates is as per IS 513D. 8Nos Corner Plates, four on each face shall be fitted to the open type rack. They shall be made of mild steel sheet and be provided with a powder coated finish. Corner Plates of 1.6 mm thickness to be provided for ensuring rigidity of the structure. Nuts and Bolts : All fasteners like nuts, bolts, clips etc. shall be supplied in galvanised condition for protection against environment and corrosion

`SOFA INTERACT 02 plus 02 Seater with privacy screens Size : 1300 L X 800 D X 1200 H The overall size of the sofa shall be 1300 Lenght x 800 D x 1200 H. Each panel fixed on the sides and back shall be a composite panel made up of recycled and recyclable materials engineered wooden boards of E1 norm like prelam particle boards / MDF sheets, acoustic fleece and aluminium extruded profiles, sound absorbent lamination and acoustically effective fabric covering. The Aluminium profile shall form the rectangular frame work that shall have engineered wooden sheets on it’s both side along with acoustic fleece, the frame should be covered by sound absorbent lamination sheet and upholstered using acoustically effective fabric. The edges of fabric and aluminium extrusions shall be sealed using PVC rubber beading. Every acoustic panel shall have two leg bushes fitted with levellers to adjust the height in accordance with ground undulation, having adjustability upto 25mm. Both the leg bushes and levellers shall be made of ABS injection moulded. Overall thickness of the panel comes should be about 55 -60mm. The acoustic panels shall be tested and certified by CSIR-National Physical laboratory. NRC (Noise Reduction capacity) level of panels shall be 0.85. Panels shall be joined via 2 way / 3way posts uniquely designed extruded aluminium profiles from 6063 grade alum alloy, confirming to DIN ISO -2768-1, and it shall have aluminium diecast caps to cover the ends. Anodized finishing shall be used as standard finish for all aluminium profiles, in compliance with IS 1868:1996 to provide best protection against corrosion as standard. The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.`

The overall size of the table shall be 1050 L x 525 D x 450 H mm. The top surface of the table shall be in boat shape design having maximum size at the middle and lesser at the ends to form this unique shape. The table top shall be made up of 18mm thick Prelaminated particle board of E1 norms. The edges shall be sealed properly with 2mm thick PVC edge banding on automatic machine. The understructure of the table shall be made from solid wood i.e properly treated and seasoned kiln dried beach wood, finished with clear synthetic PU coating for the best resilence and high durability. The legs and the frame shall be joined together by method of tenon and mortise for durability and better aesthetics. Four legs shall be provided and the cross section of leg at the bottom shall be 35x35 and top shall be 55x35 provided in tappered finish for better looks. The outer side of the legs shall be rounded and inner side shall be corner edges. The wooden frame shall be of size 55mm x 22mm thick with visible face of 55 mm front and 22mm shall be below the table top running at all four ends as well as one support in the middle.The OEM shall have ISO 9001, ISO 14001, BIFMA Level 2, Green Guard UL Gold Certification, AIOTA, IGBC Gold rated factory certification, India Design Mark with current valid dates.

Supply, erection, testing and commissioning of electrical motor driven Hydrant Pumps (Internal and External Hydrant system) of horizontal centrifugal end suction backpull out type with gland packing and capable to deliver 1620 LPM on 70 meter head, SS shaft, bronze impeller, CI casting, mechanical seal, coupled with 40HP induction motor 2875 RPM, factory fitted on base frame, with avm pad, sucxdel 100x80 mm.

Supply, installation, testing and commissioning of Diesel Engine driven common stand by pump, horizontal end suction long coupled centrifugal pump,1620LPM on 70 meter head, bronze impeller, CI casing, mechanical seal, SS shaft, sucxdel 125x100mm, coupled with 50HP eicher engine 1500 rpm, 12v battery with battery charger, factory fitted on base frame, with 200 ltr fuel tank with avm pad.

Supply, erection, testing and commissioning of electrical motor driven Jockey pump of horizontal centrifugal end suction 180 LPM on 70 meter head, SS shaft, bronze impeller, CI casting, mechanical seal, coupled with 5HP induction motor 2900RPM, factory fitted on base frame, with avm pad, sucxdel 50x32 mm.

`Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)` `(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520` `(b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-`F` insulation, conforming to IS-325.` `(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required` `(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.` 450 lpm at 35 m Head

`Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :` 100mm nominal dia

`Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :` 150mm nominal dia

`Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :` 80 mm nominal dia

Supplying, installing, testing and commissioning of M.S. puddle flenge complete with all accessories. 150mm nominal dia

`Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150mm nominal dia

`Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80mm nominal dia

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. 25 mm nominal dia ( Air vessel tank and Pressure switch manifold)

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. 25 mm nominal dia ( Air vessel tank and Pressure switch manifold)

Supply and installation testing and commissioning of differential Pressure switches of suitable range (0 to 12 bar) for pumpsets complete with necessay Ball valves, Fittings like unions / colors / reducers etc.( Standard type for main pump and Differential type for Jockey Pump)

Supply and installation testing and commissioning of Pressure gauges of suitable range (0-16 bar), 100 mm diameter dial for pumpsets completes with necessary Ball valves, siphon, Fittings like unions / colors / reducers etc.

Supply, fixing, testing and commissioning of air vessel tank shall be fabricated out of of 250 mm dia MS pipe to 1000 mm long complete with 25mm inlet, 25mm drain, 25mm dia connection for air release valve including legs, painting with red oxide primer and finished with fire red enamel paint. It shall be inclusive of all relevant pipes, valves, specials upto pump header and other accessories etc.

Supplying and erecting of Pre fabricated M.S structural steel supports such as angle, Channel, Plate etc. conforming to relevant IS standards for supporting suction and delivery pipe of each fire pump and delivery pipe to hydrant and sprinkler pipe within the pump room.

Single headed hydrant valve as per IS 5290, made of gunmetal with 63 mm dia instantaneous outlet of 80 mm dia flanged inelt ,Blank caps , chain and hand wheels etc complete.

15 M long, 63mm dia RRL hose confirming to IS 636 with gun metal instantaneous couplings and Hoses shall be stored inside the hose cabinet.

Hose reel drum of swinging type with 19mm dia Rubber braided hose of 30m length with Ball valve and Shut off nozzle, complete.

Supplying and fixing of approved make 25mm dia. automatic air release valve with unions etc. complete.

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type. 25mm nominal dia.

ABC powder type fire extinguisher of 6 Kgs. Capacity, with initial filling (Mono Ammonium Phospate Powder) in brand new cylinder with powder coated finish, Stored Pressur type, Pressure Gauge, Controllable discharge mechanism with Hose and Nozzle , confirming to IS:15683:2008.

Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, Co2 gas as per IS 15222 with controll discharge mechanism fitted with Hose and Horn applicable on Class B fire rating 21B confirming to IS: 15683:2008. CO2 Cylinder as per IS 7285 with ISI mark.

Floor indentification signage (i.e, GROUND FLOOR… ETC.,) at each stair enclosure on every floor, indicating the floor number in words, lettering size shall be 7.5cm with contrasting colour from back ground. Size shall be 15cm * 60cm.

Providing and fixing in position the signage of ` Fire Extinguisher ` to be pasted immediately above the every extinguisher. Sticker type

Providing and fixing in position the signage of ` Fire Hydrant and Hose Reel ` to be pasted on door of the every fire shaft at all floors. Sticker type

Supplying and fifing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe

Supplying and fifing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way - 150 mm dia M.S. Pipe

Providing and fixingof 12 Lit, fabricMS shee, duly red p (Fire Rewhite “S,filled with clean dry sand , incluMS wall/stand, complete as peFire SaanEngineer-Idirections

Supplying, installing and commissioning C.I. flanged `Y` type Strainer with SS screen, suitable flanges, nuts, bolts, gaskets etc. complete. 200mm dia.

Providing, fixing, jointing and testing uPVC mineral filled 100mm dia floor traps of self cleansing design with water seal not less than 50 mm., with or without vent, jointing with push fit rubber ring socket fittings complete, cutting chases / hole in floors / slabs and bringing the same in proper condition and shape after placing the trap in right position in case of suspended / open plumbing or setting the trap in 1:2:4 CC in case of concealed plumbing , etc. complete, as required. The trap shall be of following sizes: Temporary airtight PVC cover to be provided to prevent dirt entry

Providing and fixing uPVC pipe conforming to IS:4985 (10 kg/sq cm) including all fittings, This includes jointing of pipes and fittings with one step solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge and as per layout. 40 mm

Providing and fixing uPVC pipe conforming to IS:4985 (10 kg/sq cm) including all fittings, This includes jointing of pipes and fittings with one step solvent cement, trenching, refilling and testing of joints complete as per direction of Engineer in Charge and as per layout. 50 mm

Providing and fixing floor drain fixed with cement mortar complete in all respect. 110 x 50

Providing and fixing 100 mm dia uPVC hopper approximately 300 mm long with maximum 3 inlets 32, 50 or 63 mm size fabricated from uPVC heavy duty pipes , sockets, fixed to UPVC trap with joint and set in cement concrete mix 1:2:4 complete as per standard drawing . 100 mm dia

Supply of Grape Supporting Bars, 12 mm diameter, 2.4 m long, fabricated from mild steel with U-bend at ends for wire holding, surface painted (2 coats red oxide plus 1 coat enamel), suitable for trellis grape farming system.

Supply, fix and commission pedal-operated stainless steel dustbin (8–15?L capacity), grade 202/304, complete with removable inner bucket: suitable for public toilets/washrooms...Robustt 8?L Pedal Dustbin or equivalent

Providing and fixing 20 mm dia motorize valve complete in all respect as per entire satisfaction of engineer-in-charget

Supply and installation of heavy-duty flexible PVC water hose pipe, 15 meters in length, suitable for garden irrigation, home use, and car washing applications. The hose shall be complete with leak-proof tap adapter and high-strength connectors. Material: UV-resistant, durable PVC: size and quality as approved. Make: UGAOO or equivalent.

Supply, installation, testing, and commissioning of floor-mounted water cooler of capacity 80 Ltrs/hr], made of stainless steel body, with in-built storage tank, cooling compressor, and automatic thermostat control. Unit shall be suitable for operation on 230V, 50Hz, single phase AC supply, complete with all necessary internal piping, electrical connections, and drain arrangements. Shall include inlet connection, overflow connection, drainage pipe, and all accessories as per manufacturer’s standard. All materials and workmanship to be as per approved specifications and standards.

Supplying, fixing, and testing of washbasin pressmatic tap of approved make, made of heavy-duty brass body with chrome-plated finish, self-closing time delay mechanism (approximately 8–12 seconds), suitable for wall or deck mounting on ceramic or stone counter washbasins. The tap shall be complete in all respects, including all necessary fittings, washers, nuts, rubber gaskets, and connectors, and fixed as per manufacturer’s specifications and site requirements.

Supply and laying, testing and commissioning of following sizes of Copper conductor control cables through conduit on existing tray including fixing clamps and proper connections to equipments etc. complete as required. As per specification/drawings and as directed by Engineer In Charge.

Providing and fixing Fully Insulated Wooden door at all levels. Main Door frame shall be Single rebate profile of section 120 x 70 mm made out of Hard wood - Red meranti /Ivory Coast (2nd class ) as per requirement with factory made groove of suitable size. Wooden shutter must be of minimum 52mm of thickness finished with commercial ply on both faces. The Commercial ply may also be pasted with Laminate in desired shade. The composite thickness of the core insulation will be 44mm consists of lumber boards of approved make and treated wool Insulation and material. The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealed wooden lipping. All hardware`s, Fasteners and FR Glass shall be payable in Extra item. Door shutter provided with commercial ply on both faces with 1mm Thick Regular SF grade Factory pasted Laminate on both faces and Main frame made out of hardwood frame. Frame primed with Fire retardant primer. FIXTURES OF DOORS: (A) Supply and fixing of SS Ball Bearing Hinges of size 100 x 75 x 3 mm complete with SS Screws (4 No`s per panel), (B) Supply and fixing of anchor fasteners of M10*120MM length. (C) Supply and fixing of door closers of (Except shaft door). (D) Supply and fixing of Stainless Tower bolt 300mm Long for Double leaf door of height up to 2100mm with necessary screws as required. (E) Supply and fixing of Stainless Tower Bolt 600mm Long for Double leaf door of height up to 2400mm with necessary screws as required. (F) Supply and Filling the gap between wall and Door frame by using silicone sealant and Wool insulation on both side of the door. MAKE: ANAKON/NAVAIR/MAHABIR

Providing, supplying, installing, testing and commissioning RFID based Library Automation System, complete, comprising one (01) RFID staff circulation workstation for issue, return and registration of library materials: one (01) RFID enabled self checkin and check-out kiosk with touch interface for independent user transactions: one (01) RFID security gate antenna system with dual pedestal configuration (single lane) for detection of unauthorized removal of library items with audio-visual alarm indication: one (01) RFID based automated book drop station for contactless return of books with real-time update in Integrated Library Management System (ILMS): one (01) handheld RFID reader for fast inventory verification, shelf reading and locating mis-shelved books without physical handling: supply of 25,000 numbers RFID tags suitable for books, journals and magazines with long life and tamper resistance: supply of 500 numbers RFID smart cards for library members including printing: one (01) digital RFID based entry register system for recording entry and exit of users: one (01) RFID middleware software for seamless integration of all RFID hardware with existing ILMS through standard protocols such as SIP2/NCIP including configuration and testing: job work of RFID tagging of 25,000 books including de-shelving, fixing of tags at approved locations, data verification, software entry and re-shelving: complete system configuration, testing, commissioning, staff training, handholding during initial operation and one-year support, including all accessories, interface cables, mounting arrangements, power supply requirements, transportation, taxes, duties and all incidental works, complete in all respects, as per site conditions and directions of Engineer-in-Charge

Gun metal short branch pipe with nozzle confirming to IS 903.

Providing, fabricating, supplying and fixing SS 304 grade illuminated logo/signage of approved design and dimensions as per drawing (overall approx. 156` wide x 200` high), made out of SS 304 stainless steel sheets of minimum 1.2–1.6 mm thickness, laser cut and CNC formed to required profile and curvature, finished in satin / hairline / matt polish with provision of side glow LED lighting, complete with 3–5 mm thick translucent acrylic diffuser on sides for uniform light spread, using high quality LED modules/strips (12V/24V DC, IP65 rated, energy efficient) fixed inside the letters/logos, including internal wiring, connectors, and SMPS/driver of suitable capacity, complete with concealed mounting framework, studs, spacers and anchors for fixing on wall/support, ensuring proper alignment and level, including making necessary holes, backing supports, and finishing. The item includes all electrical connections up to nearest power point, testing, commissioning, complete in all respects, as per architect/engineer’s approval, including , transportation and installation. The rate shall include all materials, labour, tools, consumables and incidentals, with minimum 1-year warranty on LEDs and power supply, complete as directed at site

Providing and installing in position the following type of sign boards made out of 3mm thick `Opaque` PVC foam board with computer cut. PVC non-reflective self adhesive vinyle painted foam board, complete with mirror fasteners. Signages with printed `IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE` of 1.5cm height letters in red with white back ground. The size of the board shall be 25cm * 30cm and shall be fixed at the height of 2mts, from finished floor near Manual Call Points.

Percentage BoQ

BoQ_Ver3.0

Name of the Bidder/ Bidding Firm / Company :

PRICE SCHEDULE (This BOQ template must not be modified/replaced by the bidder and the same should be uploaded after filling the relevent columns, else the bidder is liable to be rejected for this tender. Bidders are allowed to enter the Bidder Name and Values only )

NUMBER #

Construction of Library at krishnapura Ward No. 17, Under MC Panipat. Urban.

Please Enable Macros to View BoQ information