SPL REPAIRS TO BLDG NO P-3 AND P-4 AT 54 COY ASC, PROVN OF TOILET BLOCK NEAR OLD APS LOCATION AND PROVN OF SHED FOR CI DET CCIB AT BLDG NO 205 IN THE AREA OF AGE B/R-II UNDER GE (WEST) JABALPUR

Amount

M&L for 75 mm thick as in sub base in CM 1:4:8 type D2(using 40 mm graded stone aggregate) etc all complete.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing fixed over and including 15mm thick screed bed in cm 1:6 for laying floor finish complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar laid over 10 mm thich cement morter (1:3)and jointed with ditto all as per above item etc all complete

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.18 Sqm but not exc. 0.38 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match fixed over and including 15mm thick screed bed or bedding layer with CM 1:4 complete etc all as specified and as directed.

Ditto all as per above items but as in skirting including rendering 10mm thick CM 1:4 complete all as specified and as directed.

M&L for glazed ceramic tiles colour 350x250x7mm / 450x350x7mm thick in vertical surfaces such as inskirting, dado and risers to steps set and jointed in neat cement slurry and pointed in coloured cement to match fixed over and including 10mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces as backing for tiles complete all as specified.

Demolition of cement concrete in ground floors and paving n.exc 15 cm thickness(below or above ground level)

M & L for providing plain cement concrete type B1 1:2:4 (20 mm graded aggregatet as in roof kerbs or mud stops, rounded or chamfered on edges

M & L for providing machine pressed precast concrete rubber moulded glossy finish interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade fixed over and including 50mm thick sand coushning etc all completed.

Dismantling floor, hearth or wall tiling including cement mortar bedding etc (but not backing) and removing rubbish off the premises complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:6 complete all as specified and directed.

M&L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection etc all complete

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc

M&L for rendering15 mm thick in two layers(10mm thick in CM 1:6 & 5mm thick in CM 1:4 and finished even and smooth without using extra cement etc all complete.

M & L for 15 mm thick rendering on fair faces of brick work or concrete surfaces in CM in 1:6 finished even and fair without using extra cement etc all complete

M & L for preparation of walls newly plastered surfaces & applying three coats of white wash etc all complete

M&L for 02 coats of cement base paint on walls incl preparation of new plastered wall surfaces etc all complete.

M&L for applying 2mm thick wall care Putty in two layers with two coats of oil bound distemper including primer on old surfaces including complete removal of existing wall finish of any type with wire brush, brooming, dusting and finally washing with water to clean the surface absolutely free from any kind of foreign materials and making good minor cracks etc. and surfaces absolutely even and smooth, rubbing with sand paper complete.

M & L for preparation of walls old plastered surfaces & applying two coats of cement based paint on old plastered surface etc all complete..

Demolition of brick work or stone builder masonryin cement mortar etc all complete

M&L for Brick work with Fly Ash brick straight or curved on plan exc 6mtr mean radius in CM 1:6 etc all complete

Ditto all as per item above items but except brick work.

M&L for Brick work with sub class "B" brick straight or curved on plan to any radius in half brick thick walls built in CM 1:6

M & L for preparation of new steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint over a coat of red orixed primer etc all complete.

M & L for preparation of old steel surfaces of any description over 10 cm width or girth & applying two coats of synthetic enamel paint etc all complete.

M & L for preparation of old wooden surfacesof any description over 10 cm width or girth & applying two coat of synthetic enamel paint etc all complete.

M & L providing, cement concrete1:3:6 typeC1(20mm graded aggregate) as in lintels upto 1.5m lear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

Taking down Chowkats or frames not exc. 1.5 sq. m each with shutters ( without taking off shutters from the frame)

Ditto all as per above items but exc 1.5 sq. m but n exc 4 sq. m each

S&F pressed steel frames of 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc. complete all as specified and directed.

M&L for IInd class HW 40mm thick “Factory Made Shutter” plain framed paneled shutters (two panel or more panel) with lock rail and panel of 12mm thick BWP commercial ply the size of rail and stile as per IS 1003 (part I) klin seasoned chemically pressure treated all as spd.

S&F Butt hinges medium weight cold rolled mild steel 125mm long complete.

S&F 150 mm size mild steel pressed handle type ,stove enameled black

S&F 200 mm MS sliding door bolt &clip type stone enameled black with bright bolt not less than 12mm dia with and including a minimum 6 bolt &nuts four on bolt plate and two on staple plate and fixed all as spd

S&F 200 mm size milds steel barrel tower bolt of stone enameled black with bright bolt

S&F steel windows with side hung shutters incl box type hinges with steel handle, and steel peg stay complete with glazing bars, dovetailed or welded. (Including Neccesary Fittings & Rates Should br inclusive for making goods of existing surfaces)

S&F steel windows with side hung shutters incl box type hinges with steel handle, and steel peg stay complete without glazing bars, dovetailed or welded.(Including Neccesary Fittings & Rates Should br inclusive for making goods of existing surfaces)

S&F galvanised MS wire cloth, 0.56mm nominal dia of wire average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples etc all complete.

S&F steel ventilators, factory made with top hung shuters including hinges steel peg stay with glazing bars etc all complete.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane etc all complete.

S & F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

Dismantling of asbestos cement (corruga ted, semicorrugated, etc.) sheets in roof coverings

S&F Pre-painted galvalume aluminium zinc coating GI based corrugatged steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa AZ-150 as in roof covering /cladding to wall, fixed with self tapping screws as specified

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa AZ-150 as in roof covering /cladding to wall, fixed with self tapping screws as specified

Dismantling structural steel (as in wind tie on the AC Sheet)

M&L for rolled sections as in main arms cross beam, hip and jack rafters purline where connected to common rafter and running rails and guides for sliding door fixed with angle cleats or other connecting plates.

S&F FI 40 x 6mm as in wind tie all as specified and directed

S&F in repairs suspended false ceiling system using chicago metallic (E grid)exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm thick (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600mm length) Cross Tee of dimensions 29mm X24mmX0.8mm thick and thick wall angle 22.2mmX22.2mmX 0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed , self embossed . textured designer board, water resistant termite resistant , fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) with Provn of light fixture complete all as directed. Make :- EVEREST or other equivalent as approved.

M&L for complete removal of existing water proofing treatment from top of roof and canopies / chajjas of building including removal of debris out side MD land all as directed.

Dismantling of timber scantlings unframed 40SqCm and over in section, in any position

Dismentling timber scantlings under 40 Sq. Cm in section as in rafters, purlins, unframed work etc. all as specified.

M&L for Water proofing treatment on roof surface (Horizontal & Vertical surfaces) in following sequence through manufacturer / authorized applicator of the manufacturer complete :- (a) M&L 10 mm thick rendering on roof surfaces/concrete surface in CM 1:3 complete. (b) Cleaning of plastered roof surfaces and applying a coat of bitumen primer @ 0.30 kg/Sqm on top of dry surface of finished cement mortar plaster. (c) Applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 kg/ Sqm incl cleaning surfaces. (d) Laying unrolled over the bitumen coated surface,3 mm thick polymeric water proofing membrane Hyperplas standard wt not less than 3kg /Sqm with 100 mm over laps shall be sealed by flame as per manufacturers instruction.

M&L for applying two coats on old surfaces of bituminous base aluminium paint including preparation complete

M & L for formwork to chullah hoods,chajjas, troughs and similar items including edges etc., work in rough finished flat surfaces of concrete complete all as specified.

M & L for RCC Design mix M-25 using 20mm graded aggregate as in Chajjas etc complete all as specified and directed.

Surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in soft and loose soil.

Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in any type of soil etc all complete.

M&L for cement concrete 1:4:8 Type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete.

Supply and laying Moorum / red bajari filling in floor or pavings, laid in layers n. exc 15 cm thick, spreade, levelled and rammed including watering as required etc all complete.

Supply and laying Hardcore of guage n exc 63 mm, deposited, spread and levelled n. exc. 15 cm thick, watered and rammed to true surface with broaken stone or boulder etc all complete

M&L for non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

M&L for RCC Design Mix M-25 using 20 mm graded stone aggregate in foundation, including rafts, footings, beams, plinth beams; bases for columns; etc; basement slabs, under-remed piles and mass concrete.

M&L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar works; vertical or to batter.

M&L for RCC Design Mix M-25 using 20 mm graded stone aggregate as in cloumns, pillars, piers, posts and struts

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions etc .

M & L for RCC Design Mix M-25 using 20mm graded aggregate as in beams, cantilevers, bressummers, lintels over 1.5m span

M & L for RCC Design Mix M-25 using 20mm graded aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M & L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs,etc. also splays between floors and beams, etc.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), work in rough finished flat surfaces of concrete for flat rough surface of finish.

M & L for TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Gd I, IS-432 Part I

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanized wire staples beads or in steel window complete all as specified and directed by Engr-in-charge.

S & F Factory made solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube manufactured as per SSR Part I specifications and drawing.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) manufactured as per SSR Part I specifications and drawing. consisting of frame made out of MS tubes for top & Bottom rails. MS frames shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement manufactured as per SSR Part I specifications and drawings.

S&F 100mm long aluminium butt hinges alloy with galvanised ms hinge pin, anofised and fixed type C-21

S&F 150mm long aluminium anodised barrel tower bolt and fixed

S&F 125mm long aluminium anodised handle cast type and fixed

S&F 300mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

M&L rendering 5mm thick on ceiling in cement mortar 1:3 finished fair and even smooth without using extra cement complete all as specified

M & L applying two coat of white wash on newly plastered or unplastered ceiling surfaces including preperation of surfaces, complete all as specified.

M & L for Damp proof course 40 mm th. In PCC 1:2:4 type B-0 to horizontal or vertical surface.

Returning filling in, including spreading, levelling, watering and well ramming in layers n. exc. 25 cm in soft/loose soil.

Removing excavated material n exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point.

S&F 15mm bore tubes medium grade galvanized with all fittings such as sockets, elbows, unions, Tees & short and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge. Make:- Jandal/ Prakash /TATA

Ditto all as per above items but fixed in repair

S&F 20mm bore tubes medium grade galvanized with all fittings such as sockets, elbows, unions, Tees & short and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge. Make:- Jandal/ Prakash /TATA

Ditto all as per above items but fixed in repair

M & L for cutting chases, pinning in brick walls/ stone concrete block or slab walls , making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings , steps, cills, sunshades, shelves, lintels etc; and cutting chases for concealed water tubing or cocealed conduit wiring, etc and making good , cutting not exceed 10 cm girth complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in walls

S&F PVC (SWR) bends ISI marked any radius of 110 mm bore with access door complete all as specified and directed.

S & F PVC (SWR) bends any radius, 75 mm bore

S&F PVC (SWR) 110mm bore 'T' equal or unequal complete all as specified and directed.

S&F PVC (SWR) vent cowl for 110 mm bore pipe

S&F PVC (SWR) floor trap with grating 75 mm dia incl jointing with solvent cement

Ditto all as per above items but fixed in repair

M & L for Cutting into existing manholes for connecting new drains, making good to pipe and ren-dering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required for 100 mm bore

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position all as specified and directed by Engr-in-charge. Make;- Sintex/ Plasto

Ditto all as per above items but fixed in repair

S&F vitreous china full stall urinals,white, complete including providing and fixing plugs, securing urinals to plugs with and including 60mm long brass screws, fixing flush pipe, grating and union for discharge pipe.

Ditto all as per above items but fixed in repair

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60 gms).

Ditto all as per above items but fixed in repair

S & F Bib taps, cast copper alloy with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule and fixed, 15 mm, fancy type, chromium plated fixed complete.

S & F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed, 15 mm fancy type fixed complete.

Ditto all as per above items but fixed in repair

S & F Stop valves, cast copper alloy, chromium plated concealed type screwed down, high pre-ssure, with crutch or but-terfly handle, screwed both ends for iron pipe or for unions and fixed , 20 mm fixed complete.

Ditto all as per above items but fixed in repair

S & F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long fixed complete.

Ditto all as per above items but fixed in repair

S & F Soap dish, any type, fixed to plugs with chromium plated brass screws fixed complete all as specified and directed.

Ditto all as per above items but fixed in repair

S & F PVC connections 15 mm size with PTMT nuts of length 450mm fixed complete all as specified.

Ditto all as per above items but fixed in repair

S&F chromium plated shower rose fancy type fixed to 15mm bore pipe all as specified and directed by Engr-in-charge.

S&F Towel Rail 600mm long of PTMT/SS fixed with and including Chromium plated brass screws and wooden/plastic cleats .(Minimum weight 190gms) fixed complete.

Ditto all as per above items but fixed in repair

S & F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including provn of lime concrete etc all complete .Make:- Parrayware/ Hind ware /CERA/Prayag

S & F Wash basins, Vitreous China (flat back type) any size, including cutting for and pinning in ends of brackets or erecting stand etc. complete with all accessory.Make:- Parrayware/ Hind ware /CERA/Prayag

Ditto all as per above items but fixed in repair

S&F PVC low level flushing cistern of capacity 10 litres complete with siphon handle lever float valve and PVC bend including connecting to ITWC/ ETWC and fixing on wall bracket complete all as specified and directed by Engr-in-charge. Make:- Parrayware/ Hind ware /CERA/Prayag

S&F gun metal globe or gate valve for 15mm bore pipe with iron wheel head, screwed both ends for iron pipe etc all as specified and directed by Engr-in-charge.

Ditto all as per above items but fixed in repair

Ditto all as per above items but fixed in repair

Supply and laying salt Glazed stone ware drain pipe 150 mm bore grade 'A' laid in trenches and jointed and testing complete all as specified & directed.

Excavation in post holes (or similar holes) each n. exc 0.50 cum and getting out ,returning , filling in and ramming earth or broken rubble mixed with earth around , in layers not exceeding 25 cm , watering , and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil.

M&L cement concrete as in foundations , filling and mass concrete type B2 1:2:4 (using 40 mm graded aggregate) .

S&F roof trusses (framed) trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee angle, channel or flatsections) including distance pieces cleats etc conforming to Fe 410W (Gde 250) quality A

S&F 5 to 10mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other end, or screwed both ends, each screwed and to fitted with washers and one hexagonal or square nut exc 5 cm and n exc 10 cm

S&F 11 to 15mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other end, or screwed both ends, each screwed and to fitted with washers and one hexagonal or square nut exc 10 cm and n exc 15 cm

S&F mild steel plates welded to MS pipe complete and confirming to gde Fe- 410-0 or fe- 310-0

Excavation over areas, n exc 1.5m deep & getting out in any type soil etc all as specified and complete

M&L for Machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment, confirming to IS 15658-2006of 60mm thickness M 35 Grade fixed over and including 50mm thick sand coushning etc all complete as specified and as directed.

Taking down carefully any type point wiring (light, fan, socket bell or power) , complete with fitting such as switches ceiling roses, lamp holders sockets, regulators,call bell light fitting with PVC conduit surface /concealed or wooden pattens including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces all as specified and directed by Engineer in charge.

Taking down carefully Main switch and Distribution boards any make and size .

Taking down the ceiling fan in situ and refixing after servicing, repairing and painting to ceiling fan including scratching old paint and preparation of surface for painting with one coat of white/grey enameled paint complete all as specified and directed.

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed by Engineer in charge.

M&L for Sub Main Wiring two single core PVC insulated cable of size 6.0 Sqmm multistranded copper conductor two run drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting,fixing accessories and one run of 4.0 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :-Two Nos of 6.0 Sqmm Wire and one No of 4.0 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Sub Main Wiring with two single core PVC insulated cable of size 4.0 Sqmm multistranded copper conductor drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting,fixing accessories and 2.5 Sqmm multistrand copper conductor cable as continuous earth wire complete all as specified and directed by Engineer in charge Note :- Two Nos of 4 Sqmm Wire and One No of 2.5 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed by Engineer in charge.

(a) One light point/fan point controlled by one switch.

(b) One socket point controlled by one switch on same board.

(c) One socket point controlled by one switch on Independent board.

Ditto all as per above items but with 1100 volts grade copper standard conductor cable of size 2.5 Sqmm with 1.5 Sqmm solid copper conductor PVC for 3 pin switch socket outlet15 Amp independent board complete all as specified and directed by Engineer in charge .

S & F Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and directed by Engineer in charge.

S & F Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and directed by Engineer in charge

S & F fan regulator Step type of polycarbonate complete all as specified and directed by Engineer in charge.

S & F lamp holder PVC Polycarbonate type body, with back plate for batten fitting icluding 9 watt led lamp complete all as specified and as directed by Engineer in charge.

Supply & Fixing of Indoor commercial recessed mounted luminaires energy efficient LED luminaire suitable for 600mm x 600mm for grid ceiling light not less than 36 watt with diffusers channel incluidng all accessories, internally pre-wired & making connection to ceiling rose with copper conductor of suitable size & length complete all as specified & directed. Make : Surya cat no sle fp 36 r22 or Wipro Cat Part No. CRCO10R036HP57G1 or Equivalent make & model in Philips or crompton or Havells

S & F Smart bright Batten Series, LED luminaire using LEDs 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as directed.

S & F Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed.

S & F in repair Sheet metal enclosure DBs Tripple Pole and Neutral 4- way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and directed by Engineer in charge

S & F MCB TPN 415 volts 63 Amps, C Series complete all as specified and directed by Engineer in charge .

Supply and fixing MCB single pole and neutral 240 volts 40 Amps, B Series complete all as specified and directed by Engineer in charge

Supply and fixing MCB single pole 240 volts upto 40 Amps, B Series complete all as specified and directed by Engineer in charge

Supply & Fixing single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. -1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply & fixing in repair electronic energy meter tamper proof design digital technology of SINGLE phase 3 x 240 volts 50 HZ 0.4% basic current for direct connected meter and 0.2% of basic current for CT operated meter with LCD display class-1 accuracy as per IS : 13779 Microprocessor based single phase energy meter of 10--60 Amp / 5 Amp CT operated with CT with optical communication port complete with all accessories complete with fixing accessories on finished wooden box all as specified & directed at site.

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed by Engineer in charge

Supply,laying & fixing double wall corrugated (DWC) pipes made of high density polythyline (HDPE) with all accessories i.e. all type of joints,Sockets,Elbows,bends and End caps etc.. all as specified and directed by Engr in Charge.of size 50 mm outer dia and 38 mm inner dia of Make;-Telerex/Tirupati or E-in-C approved Make

S&F GI Tubes,of size 40 mm dia light grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

S&F Exhaust fan heavy duty size sweep 300 mm sweep, 230 v, 50 Hz , complete with louvers and making hole with making the good disturbed surfaces complete all as specified and directed by Engineer in-charge. Make- Crompton Greaves, Bajaj, Havells

Supply & fix of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.Make:Havells cat part no: ENDURAPEARLSL25WLED757SASYTOPCMP or equivalent in philips or bajaj

S & F LED Mirror light fitting 2 ft TL 5 10 watt complete with fixing arrangements on wall all as specified and directed.Make- Havells LUMILINEPLUSSBS10WLED865SPCSS or equivalent in PHILIPS ,BAJAJ

Supply & Fixing sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.Make : Legrand /Schneider/ HPL

Supply , laying and testing cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cab les ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2 core 10 Sqmm complete all as specified and directed by Engineer in charge

M/s Om Infracon

chandra builders

B G PANDEY AND BROTHERS

Chetna Enterprises