ADDN/ALTN OF BLDG NO T-7/8 PERS COOK HOUSE DINNING HALL AT MH AGRA AND PROVN OF 05 HP SUBMERSIBLE PUMP TO BE INSTALLED AT SWT OF COD AGRA UNDER GE (W) AGRA

Amount

Dismantling cement (corrugated / semi corrugated, etc) sheets in roof covering including L type or J type hooks or cranked bolts etc complete all as specified and directed

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet for ridges 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ridge/cladding to wall, fixed with self tapping screws complete all as specified and directed

Taking down wooden roof truss exc 4 m but n.exc 8 m complete rafters or trussed beams span complete all as specified and directed

M&L for mild steel framed work s in roof truss (framed trussed, purlins, crane gantries, rails and fastening including distance pieces cleats etc confirming to Fe290 grade E-165 complete all as specified and directed.

Dismantling timber scantlings 40 Sq. cm and over in section and in any position complete all as specified & directed.

M & L for cutting holes into or through brick wall built in cement mortar superficial area exc 150 Sqcm not exc 400 Sqcm and making good in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix), 1:2:4 Type B1(using 20mm graded stone aggregate) as in slab/selves supported on walls, beam, and columns in floors, roof and the like complete all as specified and directed.

M&L for TMT bars of 10mm dia and over, dia cut to length bent to shape required including cranking bending spirally, hooking ends and binding with mild steel wire not less than 0.9 mm dia(annealed) complete all as specified and directed. Note - The payment shall be made only after placing of cover on manholes.

M&L for Formwork to soffits of suspended slabs/selves such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished flat surfaces of concrete complete all as specified and directed.

M&L for Formwork to edges of concrete flats, treads breaks in floors, window cill, concrete railings, openings in concrete walls, floor and roofs n exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n exc 20 cm wide complete all as specified and directed.

M&L RCC B-1 , 1:2:4 (Nominal mix) in foundations, including rafts, footings, foundation beams, plinth beams, plinth bands; bases for columns,etc basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M&L for RCC 1:2:4 (Nominal mix) type B-1 (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC 1:2:4 (Nominal mix) type B-1 (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with, in stirrups and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for form work to side of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter rough flat finished surfaces of concrete complete all as specified and directed.

M&L for formwork to side and soffits of floor or roof beam, beam haunchings, girders, bressummers, lintels, cantilevers, shelves incl sup-ports, overhands, etc also splays between floors and beam etc rough flat finished surfaces of concrete complete all as specified and directed.

M&L for formwork to side of pillars, posts, struts, piers, columns and stanchions etc square, rectangular or polygonal fair finished surfaces of concrete all as specified and directed.

S&F mild steel joist channel angle or I sections fixed independently with out connecting plates etc of grade Fe-410-0 & Fe 310-0 complete all as specified and directed..

S&F rolled section as in main and cross beams hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc confirming to Fe290 grade E-165.

M & L for preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate ) as in bed block and copping and benching embedding of hold fast etc complete all as specified and directed

Demolition of brickwork built in cement mortar including all quoins arches pillar etc. complete all as specified and directed.

Excavation in trenches, in loose/ soft soil not exceeding 1.50 meter wide and not exceeding 1.50 meter in depth and getting out complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25cm thick complete all as specified and directed .

Removing excavated soil n.exc. 50m and deposited where directed at a level n.exc. 1.5m above the starting point complete all as specified and directed..

M&L for PCC (1:4:8) type D2 (using graded stone aggregate) as in foundation, mass concrete and the like complete all as specified and directed.

M&L for brick work with old size sub class B bricks in cm (1:6) straight or curved on plan exceeding 6.00 mtr mean radius complete all as specified and directed.

Taking down cement plaster on brick or stone surface of walls including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for rendering 15mm thick on fir faces of brick work or on concrete surface in CM 1:6 finished surface fair and even complete all as specified and directed.

M&L for 15mm thick cement plaster in CM (1:4) on fair faces of brick wall Pillar and projection finished surface even and fair complete all as specified and directed.

M&L for three coats of white wash on new plastered surface on walls including preparation of surfaces complete all as specified and directed.

M&L for two coat of cement base paint over a coat of primer plaster and other surfaces with alkali resistant priming paint including preparation of newly plastered wall surfaces complete all as specified and directed.

M&L two coats of weather proof exterior paint silicon based over a coat of water based suitable primering as a base course as per manufacturer's instructions including for preparation of newly plastered surfaces of wall complete all as specified and directed.

M&L for one coats of cement base paint on old decorated surfaces of wall including preparation of surface complete all as specified and directed.

M&L two coats of oil emulsion distemper on old wall surfaces by applying 1 mm thick birla putty including preparation of surfaces and removal of exiting treatment complete all as specified and directed.

Dismantling wall and ceiling boards ( fiber pulp, insulation etc.) or insulation board /slabs/blanket any thickness including cover fillets, Frame and hangers complete all as specified and directed.

S & F Gl frame work for seamless ceiling comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre complete all as specified and directed.

M&L for 4 mm thick non asbestos fiber cement building designer boards fixed in ceiling or laid/inserted to timber/GI/ aluminun frame complete all as specified and directed.

M&L for roughening surfaces of old concrete floor by picking, sweeping, clean and washing down with water to remove dust etc including brushing neat cement slurry with 3 Kg of cement per Sqm complete all as specified and directed

M&L for non skid ceramic colour tiles joint free 7 to 8 mm thick (Square /rectangle) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in cm 1:6. complete all as specified and directed.

M&L for glazed ceramic coloured tile 350x250x7mm / 450x350x7mm thick jointed and pointed with white or coloured cement over 10 mm thick rendering in cm 1:4 on vertical surface complete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutters from the frame) area of opening not exc 1.5 Sqm each complete all as specified and directed.

All as per item No 44 before but area of opening exc 1.5 Sqm but not exc 4.00 Sqm each complete all as specified and directed.

S & F steel windows with side hung shutters with using 'Z' steel section without glazing bars including projected box type hinges, steel handle, steel peg stay etc dovetailed or welded complete all as specified and directed.

S & F steel windows with side hung shutters using steel section with glazing bars including projected box type hinge, steel handle, steel peg stay etc dovetailed or welded complete all as specified and directed.

S & F steel ventilators with top hung shutter & glazing bars hinges, steel peg stay complete all as specified and directed.

S&F framed work such as guard bars, grills etc and similar work confirming to Fe-290 Gd E-165 complete all as specified and directed.

M&L for 35 mm thick 2nd class hard wood glazed and skeleton shutters open rebated and prepared to receive glass or gauge etc divided into squares with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, provided with stiles and rails as specified in SSR Part-I Section-8 clause 8.20 (a) fixed to chowkats complete all as specified and directed

M&L for 40 mm thick Flush shutter, solid core contraction, with block board core and plywood face panels commercial type on both side fitted to chowkats complete all as specified and directed

M&L for pressed steel frames 125 x 60 x 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock, strike plate,etc complete including PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) as in filling hollow portion of frame complete all as specified and directed.

M&L Pressed steel frames 105 x 60 x 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock, strike plate,etc complete including PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) as in filling hollow portion of frame complete all as specified and directed.

M&L for PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding of hold fast etc including disturb surface of existing position complete all as specified and directed

M&L for applying two coats of synthetic enamel paint over a coat of pink primer on wooden surface over 10 cm width or girth including preparation of new or previously untreated steel surfaces complete all as specified and directed

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed (Size of hinges in 100 mm) complete all as specified and directed.

S&F 200 mm long Aluminum anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm long alluminium handles, cast type, anodized and fixed complete all as specified and directed.

S & F Alunimium sliding door bolt 300 mm long stove enamealled black with bright bolt not less than 16 mm dia with and including and minimum of 6 bolts and nuts four on bolt plat and two on staple plate and fixed etc.complete all as specified and directed.

S&F in repair 300 mm MS ordinary rat tail spring including roller and roller plate complete all as specified and directed.

S & F galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanized wire staples complete all as specified and directed

M&L for 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.5 Sqm in each pane complete all as specified and directed

S&F in repair 12 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination , fixed with screws to timber/ aluminium frame work and sealing edges of board with PVC beading by chemical adhesive complete all as specified and directed.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanised width of flaps (when open) 30mm complete all as specified and directed.

S&F mortice lock, vertical type of size 100 mm with mild steel body 4 lever complete all as specified and directed.

Demolition Cement concrete (unreinforced) in ground floors and pavings n exe 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L for 50 mm thick PCC (1:3:6) type C-1 (using 20 mm graded stone aggregate) as in plinth protection and the likes complete all as specified and directed..

M&L for 75 mm thick cement concrete 1:3:6 Type C-2 (40 mm graded stone agg) as in paths, filling under floor and the likes complete all as specified and directed.

M&L for hard core of gauge n. exc 63 mm with broken boulders or stone, spread, leveled and watered and well rammed in layers n exc 15 cm thick and the likes complete all as specified and directed.

M&L for machine pressed coloured chequered tiles 25 cm x 25 cm x 25 mm thick set, jointed & pointed in grey cement with pigment over and including 20 mm thick screed bed in CM 1:6 and the likes complete all as specified and directed.

M&L form machine cut kota stone 20-25 mm thick as in floor, laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing over 20mm thick screed bed in CM ( 1:4) as in floor complete all as specified and directed.

Cutting openings in brick wall built in cement mortar, through brick walls for door, window and other openings or enlarging existing openings, converting window into door opening etc or cutting out defective brick work for under pinning including providing fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exc 50 m and the likes complete all as specified and directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5 mm plain coloured PVC sheet, reinforced with MS square tube and fixing in opening as per specification and drawing and the likes complete all as specified and directed.

S&F Factory made solid PVC moulded door shutter 28 to 30 mm thick(stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, with particle board core, supplying & fixing in frame at site as per specifications & drawings shown in section 8 of SSR Part II and the likes complete all as specified and directed.

S&F 15mm dia tubes medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20mm dia tubes medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for gun metal ,globe or gate valve 20 mm dia with iron wheel head ,screwed both ends for iron pipe complete all as specified and directed.

S & F 15mm Bib cast copper alloy taps chromium plated fancy type with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe ) complete all as specified and directed.

S & F 15mm Stop valves cast copper alloy chromium plated fancy type ( angle valve) screwed down high pre-ssure with crutch or but ter fly handle screwed both ends for iron pipe or for unions and fixed ( 15mm bore dia of pipe ) complete all as specified and directed.

S & F 15mm bore dia Pillar taps cast copper alloy chromium plated fancy type with capstan heads screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S & F Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe complete all as specified and directed.

S & F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F shelf PTMT fixed with and incl CP brass screw and wooden / plastic cleats ( min wt 300 gm) complete all as specified and directed.

S&F Vitreous China wash hand basin white flat back size 550x400mm including brackets , waste pipe, complete all as specified and directed. Make- Cera, Hindware, Parryware

S&F1000 Ltrs Rotational moulded polyethylene water storage tanks with cover & 20mm ball valves high pressure of PTMT with epoxy coated aluminium road & high density plastic ball (cylindrical vertical with closed top) hoisted and fixed in position incl disconnecting of existing tank all as specified in SSR Part I (Capacity in liters 1000) complete all as specified and directed.

S&F Kitchen sinks made of stainless steel 1 mm thick with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x420mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F vitreous china wash down water closet pan pedestal pattern white (excl fixing bolt flushing cistern and flush pipe ) complete with seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminum hinging device complete all as spfd and directed.

S&F vitreous China Orissa pan with integral foot rest size 580xmmx440mm white with ‘P’ or ‘S’ trap front or back inlet and foot rests any pattern fixed in repair all as spfd including concrete bedding complete all as spfd and directed.

S&F low level flushing cistern of capacity 10 liter ISI marked complete with inlet ball valve , and handle including bracket of Commander/Hindware/ complete all as specified and directed.

S&F 125mm PTMT Grating with waste hole minimum weight 40 gm complete all as specified and directed Make- prayag, Polytuff and other Make approved by GE)

S&F Stainless steel toilet paper holder recessed type complete all as specified and as directed

S & F hand ablution health faucet brass chromium plated with and including 1.50 mtr long flexible tube fancy type with necessary brass nuts & rubber washers, cover with chromium plated spring complete all as specified and directed.

S&F soap dish, brass, chromium plated, size 100X60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.

S&F 32 mm waste coupling PTMT (half or full threaded) in basins, etc. with bedded in red lead cement and other end fixed complete all as specified and directed.

S&F in repairs tubular towel rail 20 mm dia D type 60cm long between flanges, brass chromium plated complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends of any radius with access door including making good disturbed portion to match the existing complete all as specified and directed

S & F 110 mm bore dia PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 75mm bore dia PVC (SWR) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F PVC (SWR) Bend any radius of 75 mm dia complete all as specified and directed.

S & F PVC (SWR) Junction (Single 'T' ) equal or un equal of 75 mm dia complete all as specified and directed

M & L PVC (SWR) Gully traps125/110 mm setting and jointing with solvent cement complete all as specified and directed.

S & F PVC (SWR) Vent Cowl 110 mm dia complete all as specified and directed

S&F 75 mm dia of outlet CI floor trap, with grating incl jointing to waste pipe fixed in cement concrete type B1(1:2:4) complete all as specified and directed.

S&F 5.0 cm thick sand stone slabs in sun shades, chajjas, shelves, roof slabs etc n.exc. 2m in length punched dressed on face and along exposed edges, self faced on other side and set and pointed in CM 1:4 complete all as specified and directed.

M&L 35 mm thick precast concrete louvers and jallies (measured solid) including all moulding frame made of cement concrete1:2:4 type B0, set in cement mortar 1:4 complete all as specified and directed.

M&L for granite stone 12 to 15 mm thick glazed (table rubbed and polished) fixed as in platform/vertical surface and the like set in cement mortar 1:4 and pointed with white cement (1:2) using marble dust with admixture of pigment to match the shade of slab and exposed edges rounded with & including screed bed or bedding layer of mortar 10 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed

M&Lfor plain cement concrete (1:4:8), type D-2, using 40 mm graded stone aggregates as in concrete bed to drain pipe of 150 mm bore laid to falls in trenches in any depth including packing under and haunching against the sides of pipes with concrete after the pipes are laid and tested complete all as specified and directed.

Supply and laying salt glazed stone ware drain pipes 100 mm dia (internal ) grade 'A' laid in trenches and jointed in cement mortar 1:1 including testing complete all as specified and directed.

M&L for PCC (1:4:8), type D-2 (using 40mm graded stone mechanically crushed stone aggregate) as in foundation of manhole complete all as specified and directed.

M&L for cement concrete 1:2:4, type B-1 (using 20 mm graded mechanically crushed stone aggregate) as in benching in manholes, coping, plinth courses, bands stopts etc including necessary use & waste of form work complete all as specified foundation, mass concrete etc complete all as specified and directed.

M&L for precast RCC (1:2:4), type B-1 using 20mm graded mechanically crushed stone aggregate as in precast slabs for covers of manholes including necessary form work and placing of manholes cover in position complete all as specified and directed.

M&L for Construction of RCC Septic tank (ST), suitable for 50 users complete all as shown on Drg No TD No. 750 sheet 1/2 & 2/2 dt 21.03.2018 and specified in tender document.

M&L cutting into existing manholes for connecting internal dia of pipe 150mm in new drain, making good to pipe and rendering cutting out existing benching for channel (1/2 or 3/4section) in cement concrete 1 : 2 : 4 type B-1 by repairing benching as required complete all as specified and directed.

Taking down carefully copper/aluminium point wiring on batten/ PVC conduit (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, including removal and making good disturbed surfaces of walls, ceilings etc by cement/ colour /plaster to match with the existing location spot complete all as specified & directed.

M&L for point wiring concealed type with 1.50sqmm PVC FRLS insulated, unsheathed, single core, multi stranded copper conductor cable 1100 volts grade including 1.5sqmm FRLS PVC insulated unsheathed stranded copper conductor cable as earth continuity conductor drawn in and Including rigid PVC conduit medium grade, concealed on wall portion and with stove enameled steel conduit medium grade on steel structural truss/ RCC roof ceiling portion surface type fixed with saddles, screws as per Engr practices of suitable size but not less than 20 mm bore with its accessories, sunken type pressed steel terminal box made of 1.2mm thick MS sheet/ anodised steel box painted with one coat of red oxide primer including 3.0 mm thick ISI marked plastic laminated sheet cover for fixing switches/ socket/regulators etc including cutting chases in wall as per standard engineering practice & making good the disturbed surfaces to match with existing for one light/ fan/street/bell point controlled by 1 one way switch 5/6 Amps complete all as specified & directed.

All as per item No-117 here in before but for One socket outlet 5/6 Amps on independent board ,(not below the switch board controlled by one switch) complete all as specified & directed.

All as per item No-117 here in before but One socket outlet 5/6 Amps controlled by one switch on same board with other switches complete all as specified & directed.

All as per item No-117 here in before but one socket out let 3/5 pin, 5/6 Amps controlled by one 1way switch on independent board (below the switch board of light points in same vertical plane) complete all as specified & directed.

All as per item No-117 here in before but using 2.5 sqmm PVC FRLS insulated stranded copper conductor cable and for one socket out let 3/6 pin, 15/16 Amps controlled by one 1 way switch on independent board complete all as specified & directed. NOTE-For item no 117 to 121 -: (i)The quoted rates shall be deemed to be inclusive for cutting chases in brick walls/pillars etc for concealing the conduits to required depth & making good the disturbed surfaces in cement mortar 1:4 including finishing the surface to match with the existing surface. The portion of point wiring at RCC Columns/Beams/Ceilings etc shall be in surface conduit of suitable size fixed on surface with using PVC rawl plug and provision of covering terminal boxes/junction boxes of any shape and size with 3 mm thick bakelight laminated sheet fixed with suitable GI screws and cup washers. (ii) Fittings like switches, sockets, regulators ,lamp holders, light fittings shall be measured and paid for separately under appropriate item of schedule A. (iii)The size of conduits shall be determined on permissible no of runs of wires as specified in SSR part-I clause 19.125 (B).However minimum size of conduit shall be 20 mm dia (medium grade)

Supply and fix switch piano, flush type, single pole, 5/6 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.38058 or equivalent as approved by GE.

Supply and fix switch piano, flush type, single pole, 15/16 Amps one way, 230 volts complete all as specified and directed. Make: Anchor Cat No.39991 or equivalent as approved by GE.

Supply and fix socket outlet, 5/6 Amps, flush type, 5 pin 230 volts complete all as specified and directed. Make: Anchor Cat No.38320 or equivalent as approved by GE.

Supply and fix socket outlet, multi-purpose 3 pin 5/6 Amps and 3 pin 15/16 Amps complete all as specified and directed. Make: Anchor Cat No.39994 or equivalent as approved by GE.

S&F for ceiling rose surface bakelite 50 x 25 mm size 3 terminals complete all as specified and directed.

S&F switch, bell push button, single pole, 5/6 Amps, one way, 230 Volts complete all as specified and directed.

Supply and fix electrical bell model city ding dong (Ding dong type) AC, 230 Volts complete all as specified & directed.

Supply and fix lamp holder insulated body with back plate for batten fitting complete all as specified and directed.

Supply & fix rotary stepped type electronic fan regulator mini flush type 100 watt 230 Volts complete all as specified & directed.

Supply & fix in replacement, single pole and neutral sheet metal enclosure (AC box) with a two pin & earth plug and socket with one no. MCB SP of capacity 20 Amps 240 volts IK-08 As per IEC 61439-3 complete all as specified & directed. .

Supply and fixing LED Bulb 15 watt, single phase, 230 Volts AC supply suitable for lamp holder complete all as specified and directed.

Supply & fix surface/wall mounting LED batten 20 watt luminaries having extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with mounting accessories complete with lamp holders fixed to wall/ ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply & fix, outdoor security light LED 36/40 watt luminaries IP 65/66 protection polyester powder coated with pressure die cast aluminium housing and robust construction with reflector cover pre anodised and flat white high transmission acrylic cover or toughened glass, natural white type with electronic driver, connector block etc with internally prewired fixed to building with and including 1.20M long bracket made out of 40mm dia light grade GI pipe bent to shape & providing clamps 2 Nos made out of 50 x 6 mm Flat iron/MS clamps & 12mm dia bolts, nuts & washers etc and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Supply & fix, surface/ ceiling mounting type 34 watt LED luminaries PLUTO NEO PENAL 2X2 environmental friendly new generation aesthetically ultra modern recess mounting with high brightness SMD LEDs as light source with reflector cover electronic driver, connector block etc with internally prewired fixed to ceiling with fixing accessories and connecting up with & including twin twisted copper flexible wire of size 0.75 sqmm from ceiling rose to fittings complete all as specified & directed.

Supply & fix surface mounting type bulkhead 10 watt LED luminaries ENDURA RUGBY NEO IP 65 environmental friendly, ultra modern energy saving , decorative oval comprising of high brightness LEDs, connector block etc with internally prewired fixed to wall with fixing accessories and connecting up with & including twin twisted copper flexible wire from ceiling rose to fittings complete all as specified & directed.

Taking down care fully sub main wiring / service connections of any size including batten/ conduit, and making good the disturbed surfaces of wall/ floor complete all as specified & directed. .

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 6.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 6.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 6.0 sqmm cable & one run of 6.0 sqmm cable along with PVC conduit including its accessories shall be measured and paid one unit length.

M&L for sub main wiring with two runs of single core FRLS PVC insulated, unsheathed, mutistranded copper conductor cable of size 4.0 sqmm drawn in and including rigid PVC rigid conduit medium grade of suitable size but not less than 20mm dia with its accessories, concealed type, including one run of single core FRLS PVC insulated, unsheathed, stranded copper conductor cable of size 4.0 sqmm as earth continuity and cutting chases to wall as per standard engineering practice & making good the disturbed surfaces as per existing complete all as specified & directed. Notes:- Finished sub main wiring with two runs of 4.0 sqmm cable & one run of 4.0 sqmm cable along with PVC conduit including its accessories shall be measured and paid one unit length.

Taking down distribution boards any size any type including MCB TPN/SPN/SP etc and making good the disturbed surfaces complete all as specified & directed..

Supply and fix MCB DB vertical type 4 way VTPN sheet metal enclosure 415 volts with 100 Amp fully insulated standard copper bus bar for each face & surrounded with neutral bars and two common neutral bar, two earth bar including cable ties for cable management suitable for housing MCCB TPN 415 Volts as incomer, IP-43, IK-09 as per IEC 61439-3 with metal doors all enclosed on standard steel sheet flush mounting type double door factory fabricated complete without MCB & MCCB but with enclosure blank plate complete all as specified and directed.

Supply and fix MCB DB sheet metal enclosure factory fabricated double door SPN 8 way with 100 amps rated copper bus bar 240 volts IP-43, IK-09 with metal doors complete all as specified and directed.

Supply and fix MCB DB sheet metal enclosure factory fabricated double door SPN 4 way with 100 amps rated copper bus bar 240 volts IP-43, IK-09 with metal doors complete all as specified and directed.

Supply and fix MCCB 4 pole 100 to 125 Amp Icu 16 Kilo Amp and Ics 100% of Icu with adjustable 70% to 100% and thermal magnetic release suitable for fixing in VTPN DB.

Supply and fixing MCB SPN 240V, 50 Hz, 10KA 'C' curve miniature circuit breaker (MCB) and current carrying capacity 32 Amp rating in the MCB DB complete with connection testing and commissioning complete all as specified & directed.

Supply & fix MCB SP, 2 to 4 Amps, 'C' curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed. (for light circuit)

Supply & fix MCB SP, 40 Amps, 'C' Curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed.

Supply & fix MCB SP, 6 to 32 Amps, 'C' curve, 240 volts, 50Hz, 10kA IP-20 as per IS/IEC 60898-1 2002 ISI marked complete all as specified & directed.

M & L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm size, buried directly in ground (earth pit not less than 2.25 M deep below normal ground level) with top edge of the plate not less than 1.5 M below normal ground level connected to and including galvanised steel earth lead wire of 4 mm dia, including 15 mm bore GI light grade protection pipe up to 1 Mtr above the floor level of the buildings where main switch, DB etc, situated, earth lead wire connected to the earth plate by means of GI bolts, nuts, washers and earth plate surrounded by 150 mm thick alternate layers of charcoal or cock dust mixed with common salt 20 mm bore medium grade GI watering pipe PCC pit in PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) cover of precast RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) duly reinforced with 8 mm formed or twisted bars @ 100 mm c/c both ways, GI wire mesh, GI sheet funnel necessary excavation in soft/ Loose soil and deposited the surplus soil to a distance not exceeding 50 mtr away from starting point, all as per electrical plate no:3 of SSR part-1 .

M&L for electrically disconnecting and taking down existing ceiling/Exhaust fans from any height or in any position from existing bldg and keeping in safe custody for reuse at site after necessary repair/ servicing & painting with one coat of synthetic enable paint and writing of MES/identification No. of fans and re hanging/ re-fixing in original position but including replacement of three core flexible copper conductor cable from ceiling rose to fan connector block of size 0.75 Sqmm and hanging fan clamps, nuts, bolts and rubber reel bush etc & testing for proper functioning complete all as directed at site by Engr-in- Charge

S&F iron metal body heavy duty exhaust fan 300mm sweep, double ball bearing, copper wound, with louvers, 230 volts, 50 Hz, including electrically connecting from ceiling rose to fan connector with 0.5 Sqmm stranded copper conductor 3 core flexible cable cord complete all as specified and directed. Make:- Bajaj/Usha/ Havells

S&F iron metal body heavy duty exhaust fan 450mm sweep, double ball bearing, copper wound, with louvers, 230 volts, 50 Hz, including electrically connecting from ceiling rose to fan connector with 0.5 Sqmm stranded copper conductor 3 core flexible cable cord complete all as specified and directed. Make:- Usha/ Bajaj/ Havells

Supply and fix ceiling fan, 1200mm sweep, minimum 220 CFM, 230 V, BEE 5 star rated, BLDC (brushless direct current motor ) type complete with standard accessories i.e (three blade, 02 Nos canopy, electronic type modular fan regulator 90 to 100 W, down rod of length 1.5 mtr to 2.0 mtr long, 01 No. fan hock, 02 Nos hanging clamps with rubber real insulator, nuts, lock nuts, bolts, washers, split locking pins etc), double ball bearing, copper wound with synchronous motor, including electrically connecting from ceiling rose to fan connector with 0.5 Sqmm stranded copper conductor 3 core flexible cable cord complete all as specified and directed. Make :- Bajaj, Havells, Bajaj, Khetain, Usha

Supply, installation, commissioning of Water cooler fully stainless steel, electric driven single phase having approx storage and nominal cooling capacity of 40 Ltrs per hour and storage capacity of 80 Ltrs with 2 Nos cold water outlet complete all as specified and directed. Make :- Blue Star/ Godrej/ Voltas/ Usha

Supply and fix electric water heater, storage type steel body with fiber glass coated inner tank and heating element up to 2 KW capacity 25 liter, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc. including fastener mild steel 100 mm long x 10 mm dia with pin and bolts complete for hanging of geyser complete all as specified & directed.

Supply & Laying, testing ,cable XLPE insulated screened PVC bedded galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade, with stranded aluminium conductor of size 25 Sqmm 4 core compile all as specified and as directed. Make :- Havells, Grandlay, Polycab, Finolex

Supplying and laying un-reinforced precast concrete cable cover LV type-I flat size 250 mm x 150 mm x 40 mm in trenches for protection of cable complete all as specified & directed.

M&L for sand cushioning dry fine for cable cushioning below and above the cable complete all as directed

Supply and fixing GI Pipe 40mm Light grade , for cable protection laid in trench under road or path or fixed on pole or wall with clamps with all fittings complete all as specified and as directed at site,. Make :- TATA, Jindal, Prakash Surya

M&L For Drilling trial bore in any strata 200 mm dia with the help of drilling machine chain pully, tripod and other reqired T&P related to drilling hole complete.

M&L for lowering UPVC plane Casing pipe 200 mm dia of pressure rating 12 Kg/sq cum including making slots wherever necessary complete.

Supply and packing pea gravel of 2 mm to 6 mm size of approved quality as orderedto pack around the casing/slotted pipes in bore well complete.

M&L for MS well cap 2 mm thick of 200 mm dia size on top of the pipes with locking arrangement complete all as specified and directed.

M&L for PVC bail plug of 200 mm dia complete all as specified and directed.

Two number MS Clamp made out of flat iron 50 mm x 6 mm thick suitable for holding cloumn pipe & cashing pipe including nuts & bolts complete all as specified and directed.

Supply and fixing UPVC column pipe 80 mm bore 12 Kg working pressure standard grade for pump set including plastic rope for supporting of submersible motor necessary fitting and connection to submersible pump complete all as specified and directed.

Supply & Lowering commissiong and testing only of submersible pump set three phase, 415 Volts, capacity 5 HP and discharge head 75 Mtrs complete all as specified and directed.

Supply & fixing PVC insulated submersible cable 10 Sqmm three core 1100 volt grade complete all as specified and directed. Make : Plaza / Kalinga / Finolex/ Havells

S&F Gun metal gate valve 80 mm ISI marked IS-778 screwed down for iron pipe or ferrule including fittings such as union, socket, nipple, check nut etc including cutting of existing GI pipe and fixing properly complete all as specified and directed.

Supply and fixing DOL submersible motor controller starter three phase 415 Volt with MCB, over load relay, under volt/over volt relay, contractor, voltmeter, Amp meter, ON & OFF push butten including fixing arrangement suitable for 5 HP submersible pump complete all as specified and directed.

M&L for cast iron non return valve (NRV) both end flnged of size 80 mm bore (ISI Marked) without by pass arrangment pressure rating PN1.6 including rubber gasket, mild steel bolts, nuts, washers etc and commissioning & testing all as specified and directed.

Developing tube wells by compressed air with minimum pressure of 10 Kg/sqcm and minimum 450 CFM all as specified in IS 11189-1985, para 4.3 and directed. Note - Compressor, pump pipe and other allied items will be arranged by contractor and no extra payment will be made by the dept.complete all as specified and directed.

Yield testing for the bore well with the help of V notch tank 90 degree by continuously pumping for 16 Hrs. complete all as specified and directed.

Chemical and bacteriologocal testing of sample from approved laboratory to ensure portability of water complete all as specified.

Geological survey for CGWD.complete all as specified.

m/s meetu enterprises

m/s shanti consruction co

M/s Shrangi Rishi Construction

PD GUPTA AND COMPANY

M/s Ram Naresh Construction Co.

scjha&sons

M/S RISHI RAJ AGRAWAL

VISHESH BUILDERS