PROVN OF MAIN GATE ALONGWITH SENTRY POST AT NIMU MIL STN UNDER AGE (I) NIMU

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, laying of pipes etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard / dence soil, complete all as specified & directed.

Plain cement concrete 1:4:8, type D-2 (using 40mm aggregate) as in foundations, filling and mass concrete, complete all as specified and directed by Engr-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, complete, all as specified and directed by Engineer-in-Charge.

Formwork to sides of column, posts for square and rectangular rough finished surface, complete, all as specified and directed by Engineer-in-Charge.

Form work to sides of roof beams band and similar and soffits of girder, lintle, cantilever shelves including supports flat rough surface of concrete complete all as spd and directed.

Form work to soffits of suspended slabs, such as roof slabs, landings and similar work not exceeding 200 mm thick with rough finished flat surfaces of concrete, complete all as specified and directed by Engr-in-Charge.

TMT bars 10 mm dia and over, cut to length , bent to shape required including cranking , bending spirally for hooping for columns, hooking ends, binding with and including mild steel wire (annealed) not less than 0.9mm dia , complete all as specified and directed by Engr-in-Charge.

TMT bars 06 mm dia and including 10 mm dia in stirrups, spacers and bindersc cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild stee wire (annealed), not less than 0.9mm dia complete all as specified and directed by Engr-in-Charge.

Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate ) as in foundation, including rafts, fotting, foundation beam: plinth beams; bases for columns, etc, basement slabs, under reamed piles and mass concrete, complete all as specified and directed by Engr-in-charge.

Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate ) as in Column, complete all as specified and directed by Engr-in-charge.

Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate ) as in Beams, Cantilevers, bressummers, lintels over 1.5m span, complete all as specified and directed by Engr-in-charge.

Reinforced cement concrete 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregate ) as in slabs supported on walls, beams and columns in floors, roofs, complete all as specified and directed by Engr-in-Charge.

Precast cememt concrete block masonary with solid blocks type-C-1 1:3:6 (using 20mm graded crushed stone aggregate) exc. 10cm in width and setting in cement mortar (1:6), complete all as specified and directed by Engr-in-Charge.

Rendering 15 mm thick plaster on fair face of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra ement. complete all as specified and directed by Engr-in-Charge.

Preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer, complete and all as specified and directed by Engr-in-charge.

Framed work as in doors, or gates of angle or other section with gusset plates, rails, braces, etc, complete, drilled for fixing of steel sheeting or other covering, Doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete and all as specified and directed by Engr-in-charge.

Rolled mid steel in channel, angle or tee section fixed independently, complete and all as specified and directed by Engr-in-charge..

Applying two coats of synthetic enamel painting to new surfaces steel based over a coat of red oxide primer exc. 10 cm width/girth including preparation of surfaces including filling with filler where required, complete all as specified and directed.

Second class hardwood in clean sawn timber fixed in scantlings as in gate framed work complete and all as specified and directed byEngr-in-charge.

2nd Class hardwood fillets of exc. 06 and n.exc 13 Sq cm as in sectional area, bullnosed, splyed, chamfered or round on one edge or face section, clean sawn, secured with nails or brads complete all as specified and directed by Engr-in-charge.

2nd Class hardwood fillets of exc. 13 and n.exc 25 Sq cm as in sectional area, bullnosed, splyed, chamfered or round on one edge or face section, clean sawn, secured with nails or brads, complete all as specified and directed by Engr-in-charge.

2nd Class hardwood clean sawn battens of sectional area exc 15 & n.exc 25 sqcm fixed at spacing of 20 cm centres, complete all as specified and directed by Engr-in-charge.

Boarding 20mm thick, Hardwood 2nd class, Planed one side with butt joints upplied & fixed with nails in any situation (except flooring and skirting), complete all as specified and directed by Engr-in-charge

Pre- painted galvanized plain sheet as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed by Engr-in-charge.

Preparation of new wooden surfaces of any description over 10cm in width or girth and applying two coats of S/E paint over a coat of pink primer, complete all as specified and directed by Engr-in-charge.

Returning, filling in excavated soil including spreading, leveling watering and well remming layers not exceeding 25 cm thick complete all as specified and directed by Engr-in-charge.

Removing exavated material (Soils) to a distance not exceeding 50m and depositing where directed at a level not exceeding 15.m above tghe starting point, complete all as specified and directed by Engr-in-charge

2nd class Hardwood Plain, solid, straight chowkats and frames, wrought, rebated on the solid,, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed by Engr-in-charge.

30mm thick shutter, 2nd class Hardwood, Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for ecuring glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, SSR Part I, Section 8 clause 8.24(b) as in windows & ventilators, complete all as specified and directed by Engr-in-charge.

35mm thick 2nd class Hardwood, Plain, framed, Panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified and directed by Engr-in-charge.

125 mm long Butt hinges, medium weight, cold rolled mild steel, complete all as specified and directed by Engr-in-charge.

Exruded aluminium alloy handles, 150mm size, fabricated type, anodised, complete all as specified and directed by Engr-in-charge.

125 mm long, Aluminium anodised, barrel tower bolts of extruded section, complete all as specified and directed by Engr-in-charge.

200mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed by Engr-in charge.

300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed by Engr-in-charge.

5.5mm thick Sheet glass, ordinary quality and glazing with beads in square exc 0.5 sq. m in each pane, complete all as specified and directed by Engr-in-charge.

Preparing new plastered surfaces of walls and applying two coat of dry distemper white or tinted over a coat of Chalk whiting, on plastered surfaces, prepara-tory to distempering, complete all as specified and directed by Engr-in-charge.

Brass Alphabet of size 6"x12", complete all as specified and directed by Engr-in-charge.

M/S SONAM NAMGIAL (BID ID -3064691)

M/S TSERING ANGCHOK (BID ID -3064724)