REPAIR TO ROAD AND ROAD FURNITURE, CLEANING AND REPAIR OF SEWAGE LINES AT CHAUHTAN HILL UNDER GE (AF) UTARLAI

Amount

Dismantling of Brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars,precast concrete articles and precast concrete block walling etc. and removing rubbish from site all as specified and directed.

M&L for cement concrete (1:4:8) type D2 using 40 mm graded stone aggregates as in foundation, filling and mass concrete complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

Ditto as per Item No 03 but except stone

M&L for precast cement concrete block masonry with solid blocks of PCC 1:3:6 type C1 using 20 mm graded stone aggregate, exc. 10 cm in width and setting in CM 1:6 complete.

M& L for cement concrete type B0 1:2:4 type (12.5mm) graded graded graded aggregate) in benching, Coping all as directed.

M&L for rendering 15 mm thick in CM (1:4) on stone masonry surfaces or surface other than fair face of brick-work/Block work or on one side of lathing finished even and smooth without using extra cement with using integral water proofing compound as per manufacturer instructions. Note: Integral Water Proofing compound shall be measured and paid for separately as “Supply only”.

Supply only integral water proofing compound ISI marked.

Excavating in trenches in any type of soil, n.exc. 1.5m wide and n.exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n.exc. 10 sqm on plan and n.exc 1.5m in depth and getting out.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25cm.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point.

Demolition and breaking up drain pipes, (Salt glazed stoneware, AC or reinforced concrete) 150mm (internal dia) set in cement mortar.

Demolition and breaking up drain pipes, (Salt glazed stoneware, AC or reinforced concrete)100mm (internal dia) set in cement mortar.

M&L for cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in bed to drain pipes of size 150 mm bore, including packing under & haunching against the sides of pipes after they are laid and tested.

All as per item No.14 above but 100mm bore drain pipe.

M&L for Reinforced concrete pipes, class NP2, with collars of 150 mm internal dia, grade `A’ ISI marked laid to slope in trenches, jointed in CM 1:1 and tested complete all as specified and as directed.

All as per item No.16 above but 100mm internal dia.

S&F in repair PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement

M&L for cutting into existing manholes for connecting new drains of 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel ( ½ round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required.

All as per item No.19 above but for 100mm internal dia.

Demolition of reinforced cement Concrete of any description and in any position not otherwise specifically provided for

M&L for precast reinforced cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate in landings, cover slabs (for manholes/septic tank/soak well etc.) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds etc all as specified. (Reinforcement shall be measured and paid for separately).

M&L for mild steel TMT bars 6 mm to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

M&L for mild steel TMT bars 10 mm dia and above, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia.

M&L for cleaning pipe lines 150mm dia by rodding from Man holes and well flushing with water after cleaning all as specified & directed. Note:- Contractor shall depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00am to 5.30pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

All as per item No. 25 above but 100mm dia.

Clearing of blockage of Nahani Trap of bath room, kitchen by rodding blockage including taking down/refixing of grating etc complete all as specified and directed by Engineer-in-Charge. Note- Contractor shall depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00am to 5.30pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

Clearing of blockage of gully trap of bath room, kitchen by rodding blockage including taking down/refixing cover complete all as specified and directed by Engineer-in-Charge. Note- Contractor shall depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00am to 5.30pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

Clearing of blockage of Indian type WC/ Europion type WC by rodding/ pumping by hand including taking out door/refixing of over access covers etc complete all as specified and directed by Engr-in-Charge. Note:Contractor shall depute his supervisor to collect complaint from AGE(B/R)-II office at 9.00am to 5.30pm & after cleaning the line get checked from Engineer-in-Charge.Complaint of blockages should be completed with in 24 hrs, if the same is not attended, a recovery of Rs 250/- per complaint shall be made.

Cleaning of manholes of size n.exc 1.00 sqm plan area (internal) and n.exc 1.00 Sqm depth from GL including removal of manhole covers carefully, cleaning of sludge etc and refixing the manhole covers with cement mortar (1:4) (Sluge shall be removed outside MD land)

All as per item No. 30 above but depth exc 1.00m and n.exc 2.00m.

Pumping out sewage water/sludge from existing septic tank/soak well of any size & capacity and removal the sludge to out side MD land

S&F in repairs solar road studs made out of aluminium housing and precast construction solar powered by SEIMENS monocrystal solar panel 2W 120mA type of battery NI-CD 1.2 volt 2500m AH & flash rate 2Hz or 70Hz view distance over 300mtr. Fitted with 2Hz EL-805-3 pieces each side on two ends total 6 pieces LEDs, flashing upto 12 Hrs of light at night and solar battery automatically charged in day/ sun light duly fixed with cement and hardener. 125 x 125 x 25mm in red /yellow colours complete all as specified and directed.

S&F in repair retro reflective road delineator made of ABS plastic body having two 100 mm dia circular reflectors & two rectangular reflectors of 70mm x 23 mm fixed on both sides of 1000 mm long MS pipe 50mm dia fully powder coated guide post to fixed with screws/embeded in concrrete PCC 1:2:4 type B-2 usuing 40 mm graded crusted stone aggregate having size 20cm x 20cm x 20cm complete all as specified and directed. Note Reflector shell be covered with 4mm dia galvanised wire of mesh size 100 x150mm .

S&F in repairs speed bumps made from heavy duty ABS high resistance wear & tear property UV stabilized black & yellow combination high reflective reflector having available on both sides in red & yellow colour with L= 500mm, W=380mm, H=50mm complete all as specified and directed.

Supply and fixing in repair Road Safety Convex Mirror 100 cm dia Model No OS-789 of make Oscar or equivalent make including stand/padestal embedded /fixed in to concrrete PCC 1:2:4 type B-2 usuing 40 mm graded crusted stone aggregate having size 45x45x60cm and necessary earth work.,complete all as specified and directed by Engr-in-Charge.

Dismantling of old / brocken cautionary mandatory and information sign boards of any size, any position and any description including frame work embedded in ground or PCC, complete as as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

M&L for providing cement concrete in foundation filling and mass concrete 1:2:4, type B2 (using 40mm graded aggregare), complete all as specified and directed.

S&F framed work such as cautionary mandatory and information sign boards and similar work con- forming to stainless steel grade 304, complete all as specified and directed.

S&F in repairs retro reflective cautionary mandatory and information sign boards as per IRC 67 made of high intensity reflective grade sheeting fixed over aluminium sheet 1.5mm thick, including writing letters(computerized cutting) in any nos and any size with reflective micro prismatic tape in any colour shade incl making arrow/sign, border and logs,complete all as specified and directed. Note: The rate of 1.5mm thick sheet shall beincluded in this item.

S&F Framed work such as cautionary mandatory and information sign boards, doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel anging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing and similar work structural steel con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F in repairs retro reflective informatory sign board as per IRC 67 made of high intensity reflective grade sheeting over MS black sheet 1.25 mm thick , including writing letters (computerized cutting) in any nos and any size with reflective micro prismatic tape in any colour shed incl making arrow/ sign, border and logs with same material,all as specified and directed. Note: The rate of 1.25mm thick MS sheet shall beincluded in this item.

M&L for preparation of new steel surface of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide , complete all as specified and directed

M&l for applying one coat of synthetic enamel paint incl preparation of old concrete surface complete all as specified and directed

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for and removal from site exc. 50 m complete all as specified and directed.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

M&l for applying two coats synthetic enamel paint over a coat of primer incl preparation of new stone /concrete surface complete all as specified and directed

M&L for 75mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) as sub base of floor.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as directed.

M&L for chequrred cement concrete tiles of size 300x300x22 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement and match the surface of tiles as floor with and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 60 mm thick, M-35 Machine pressed precast interlocking paver block any shape and size confirming to IS 15658-2006 fixed with cement and pigment glossy finish coloured as approved by GE fixed on sand cushion 40 mm thick & ends to be closed with PCC 1:2:4 type B-2 (Using 40mm graded stone aggregate) as site reqd to filing the gaps between tiles and road edgs complete all as specified and directed.

M&L for marking 2.5mm thick centre line , side line, stop line, dashes, arrows, brackets & similar work on road surfaces as per IRC pattern with thermo plastic paint of approved quality & make with 8% glass beads laid at temperature of 160 degree centigrate with a special applicator machine complete all specified and directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n.exc 30cm high per 10 Nos (per CM Height) including painting of base with white and black colour complete all as specified and directed by Engr-in-Charge.

M/S Tanisha Traders