REPAIR TO TOILETS, BATHROOM, BATHING POINTS, SUNKEN AND WALL WATER PROOFING TREATMENT OF CERTAIN OTM ACCN UNDER AGE B/R II OF GE SGNR AT SGNR MIL STN

Amount

M&L for reinforced cement concrete type B1 1:2:4 (20 mm graded aggregate) as in slab supported on walls, beam and column in floors, roofs,landings,balconies,deck slab, parapet walls and in shelves and etc and setting in mortar complete with joints to match complete all as specified and directed by Engr-in-Charge. Note : Rates of Demolition of RCC of any description is included in quoted rates.

Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed by Engr in charge

M & L mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engr-in-Charge.

M&L brick work with sub class B bricks straight or curved on plan exceeding 6 mtr mean radius in cm 1:6 etc including demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches , pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles.complete all as specified and directed by Engineer - in - Charge. Note : Rates of demolition are included.

M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed by Engineer-in-Charge:- (a) applying 15 mm plaster in CM 1:3 with WPC on raised verticle surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c) Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (g) Cement concrete 1:4:8 over the coating as per requirment. (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout. (k) Providing 40 mm bore GI pipe spout length 15 cm beyond external surface of the wall complete all as specified and directed by Engineer-in-Charge. Make:- Dr. Fixit/Fosroc/STP/Choksey/SIKA or equivalent Note: (i) PCC filling in sunken portion will be measured seperately. (ii) Rates for Demolition of cement concrete (unreinforeced) of any description and in any position for sunken portion (below or above ground level) Note : (i) Sunken treatment shall be applied by the Company's authorised applicator firm only. (ii) Contrator has to get prior approval of applicator or authorised agency by submitting its authorisation letter to this office for approal prior to commencement of work. Department will conduct an officical verification from the manufacturer of its authorised agency.(iii) Submission of 10 years warranty certificate for Roof Treatment and 5 years warranty certificate for Roof Treatmet and 5 years warranty for sunken treatment is mandatory after completion of work. (iv) The cost of scaffolding, temporay supports work, if required at certain places is included in the respective items catered for repair itself. No extra cost shall be paid for the same.

M&L for PCC (1:5:10) type E-2 (using 40mm graded bricks aggregate) as in foundation, filling & mass concrete or filling in sunken floor complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick wall including racking out joints, hacking for keys scrubbing down with water complete all as specified directed by Engr-in-Charge.

M&L 15mm thick, rendering in cement mortar CM 1:4 to brick/concrete wall surfaces finished even & smooth without using extra cement complete all as specified and directed by Engr-in-Charge. Note : Work to be carried out upto 10 mtr height

M&L 15mm thick, rendering in cement mortar 1:6 to brick/concrete wall surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 5 mm thick cement plaster in cement mortar 1:3 on ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

Prepration of New external plastered wall surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1mm thick waterproof putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion Complete all as specified and directed.

Prepration of New internal plastered wall/Ceiling surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1.5 mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion complete all as specified and directed.

Prepration of old existing external plastered wall surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of exterior emulsion paint (light shade) with highlighter of any approved shade, @ 10 sq.m/litre/1 coats by using roller to old existing external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 10 sq.m/1 coat as recommended for under coat by manufacturer of exterior emulsion complete all as specified and directed.

Prepration of old existing internal plastered wall/Ceiling surface and applying complete all as specified complete all as specified and directed by Engineer-in-charge of the following :- (a) Applying 1.5 mm thick wall care putty on wall surface and smoothening the surface prepatory to paint. (b) Applying 02 coats of interior emulsion paint (light shade) @ 20 sqm/litre/1 coats by using roller/brush to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion complete all as specified and directed.

Taking up or down GI steel water tubing 15mm bore and connections including fittings from floor/walls/ceiling complete all as specified and directed by Engr-in-Charge.

S & F Galvanised steel water tubing 15 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good complete all as specified and directed by Engr-in-Charge.

Supplying and laying of CPVC pipes of dia 20 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

Suppy and fix for pipe supporting clamping - single pipe of dia 15 mm (1/2") down take pipe line fixing done with Clamping System consists of Mono Bracket, U Bolt Rubber sleve mounted sustem running vertically with wall distance 75 mm (3'):- Pipe support Clamping Made of :- 1. Mono Bracket for 15 mm (1/2") piep having wall distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079): Material size 48 mm x 3mm with ribs and notch are Hot Dop Galvanised + Zn Al Flake Coated having Salt Spray Test (Test Method- ASTM B-117-2019) result 2000 hrs. 2. U Bolt rubber sleeve mounted are made of low carbon mild steel with Rod dia meter 7 mm approx : Zn Al Flake coated with noise abosring semi transparent ribbed silicon rubber slleve ; with Hex flange Nut BSQ 5/16 x18 x8 13 with serration set - Zn Al Flake coated. Hot dip Galvanising : as per IS 2629 (1985) -610 gms/32(>85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 1020 3.1. Material Qualaity : for one unit :- (a) Mono Bracket for 15 mm (1/2") pipe, wall distance 75 mm (3") - 01 Nos, (b) U Bolt Rubber sleeve mounted for 15 mm (1/2") GI/UPVC/CPVC Pipe Dia-1 Nos. (c) Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 02 Nos. Fixing Details : Pipe support clamping unit to be fixed at every metre distance in the duct as complete all as specified and directed by Engineer in Charge

Taking up or down GI Steel water tubing 20mm bore and connections including fittings from floor/walls/centrings complete all as specified and directed by Engr-in-Charge.

S & F Galvanised steel water tubing 20 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good complete all as specified and directed by Engr-in-Charge.

Supplying and laying of CPVC pipes of dia 25 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

Suppy and fix for pipe supporting clamping - single pipe of dia 20 mm (3/4") down take pipe line fixing done with Clamping System consists of Mono Bracket, U Bolt Rubber sleve mounted sustem running vertically with wall distance 75 mm (3'):- Pipe support Clamping Made of :- 1. Mono Bracket for 20 mm (3/4") piep having wall distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079): Material size 48 mm x 3mm with ribs and notch are Hot Dop Galvanised + Zn Al Flake Coated having Salt Spray Test (Test Method- ASTM B-117-2019) result 2000 hrs. 2. U Bolt rubber sleeve mounted are made of low carbon mild steel with Rod diameter7 mm approx : ZN Al Flake coated with noise abosring semi transparent ribbed silicon rubber slleve ; with Hex flange Nut BSQ 5/16 x18 x8 13 with serration set - Zn Al Flake coated. Hotdip Galvanising : as per IS 2629 (1985) -610 gms/32(>85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 1020 3.1. Material Qualaity : for one unit :- (a) Mono Bracket for 20mm (3/") pipe, wall distance 75 mm (3") - 01 Nos, (b) UBol Rubber sleeve mounted for 20 mm (3/4") GI/UPVC/CPVC Pipe Dia-1 Nos. (c) Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 02 Nos. Fixing Details : Pipe support clamping unit to be fixed at every metre distance in the duct as complete all as specified and directed by Engineer in Charge

Taking up or down GI Steel water tubing 25mm bore and connections including fittings from floor/walls/centrings complete all as specified and directed by Engr-in-Charge.

S & F Galvanised steel water tubing 25 mm bore medium grade with all fittings concealed including cutting chases to brick wall/ceiling or laying in floors and making good complete all as specified and directed by Engr-in-Charge.

Supplying and laying of CPVC pipes of dia 32 mm SDR 11 & Plain CPVC SDR 11 inlcuding all fittings i.e.Brass elbow, Brass Tee, Male threaded Brass adaptor, Female threaded brass adaptor, unions ball valves, flange and tank adaptor etc) concealed including cutting chases to brick wall/ceiling or laying in floors/trenches and making good complete all as specified and directed by Engr in Charge.

Suppy and fix for pipe supporting clamping - single pipe of dia 25 mm (1") down take pipe line fixing done with Clamping System consists of Mono Bracket, U Bolt Rubber sleve mounted sustem running vertically with wall distance 75 mm (3"):- Pipe support Clamping Made of :- 1. Mono Bracket for 25 mm (1") piep having wall distance 75 mm (3") made of Low Carbon Hot Roll Gauge Corrected Oil Pickled and Drawn (HROP D) Steel (IS 1079): Material size 48 mm x 3mm with ribs and notch are Hot Dop Galvanised + Zn Al Flake Coated having Salt Spray Test (Test Method- ASTM B-117-2019) result 2000 hrs. 2. U Bolt rubber sleeve mounted are made of low carbon mild steel with Rod dia meter 7 mm approx : Zn Al Flake coated with noise abosring semi transparent ribbed silicon rubber slleve ; with Hex flange Nut BSQ 5/16 x18 x8 13 with serration set - Zn Al Flake coated. Hot dip Galvanising : as per IS 2629 (1985) -610 gms/32(>85 microns). Material Grade : IS 1079 used as per MTC confirms to EN 1020 3.1. Material Qualaity : for one unit :- (a) Mono Bracket for 25 mm (1") pipe, wall distance 75 mm (3") - 01 Nos, (b) U Bolt Rubber sleeve mounted for 25 mm (1") GI/UPVC/CPVC Pipe Dia-1 Nos. (c) Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 02 Nos. Fixing Details : Pipe support clamping unit to be fixed at every metre distance in the duct as complete all as specified and directed by Engineer in Charge

Fixing only 1000 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed by Engr-in-Charge.

S&F 25 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete all as specified and directed by Engr-in-Charge.

S&F in repair 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F MS falt iron 50/6 x 6mm as in hold fast confirming to Fe 290 Gde E-165 complete all as specified and directed by Engineer in Charge

Dismantling of cast iron or reinforced concrete drain pipes jointed in cement mortar and taking out of trenches/wall complete all as specified and directed by Engr in Charge

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, jointed with solvent fixed to wall or laid in trenches with matching PVC SWR rings including cutting holes and making good the disturbed portion with PCC (1:2:4) type B0 including clamps and bends/Tee/elbow/ branch piece complete all as specified & directed by Engr-in-Charge.

Suppy & fix for pipe supporting clamping - single pipe of PVC dia 110 mm (4") down take pipe fixing done with clamping system consist of Profile bracket & continous slottted C Channle, U Blot rubber sleeve mounted system running vertically with wall distacne 75 mm (3") :- Pipe Support Clamping made of :- (a) Profile bracket having wall distance 75 mm (3") made of Low Carbon Rol Gauge Corrected Galvanised , ZU Al Flake coated having salt spray (TEst Method - ASTM B-117-2019) result 2000 hrs with SS 304 Hex Flange Bolt with serration 5/16 x 3/4 (A/F 13 mm) as per DIN 6921 and SS 304 Hex Flange Nut BSW 5/196 x 18 x 18 x 1.3 wieth serratio as per DIN 6923. (b) Continuous slotted 'C' channelw with ribs to be used of size 250 mm (10") made of Low CArbon Hot Roll Gauge corrected Oil pickled and Drawn (HROP D) Steel (IS 1079) are hot dip Galvanised, Zn Al Flake Coated with material thickness of 3 mm. U Bolt rubber sleeve mounted are made of low Carbon mild steel with Rod diameter 7 mm approx; Zn Al Flake coated with noise absorbing semi tranparent ribbed silicon rubber sleeve: with Hex Flange Nut BSQ 5/16 x 18x18x 13 with serration set as per DIN - 6923 Zn Al Flage coated. Hot dip Galvanising : as per IS 2629 (1985) -610 gm/m2(>85 microns). Used as per MTC confimrs to EN 10204 3.1. One unit : 1. Profile bracket wall distance 75 mm (3")- 02 Nos 2. Continuous slottted C chanbnel of size 250 mm (10") -01 Nos. 3. U bolt runner sleeve mounted for 75 mm (3") PVC pipe dia -01 No and Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 4 Nos . Fixing details : Pipe support c,amping unit to be fized at every 1-2 meter distance in the duct complete all as specified and directed by Engineer - in - Charge.

Suppy & fix for pipe supporting clamping - Two pipes of PVC dia 110 mm (4") and 75 mm (3") down take pipe fixing done with clamping system consist of Profile bracket & continous slottted C Channle, U Blot rubber sleeve mounted system running vertically with wall distacne 75 mm (3") :- Pipe Support Clamping made of :- (a) Profile bracket having wall distance 75 mm (3") made of Low Carbon Rol Gauge Corrected Galvanised oiil pickeled and drawan (HROP D) steel (IS 1079; material size 32 mm x 3mm with ribs and notch are Hot Dip Galvanised , ZU Al Flake coated having salt spray (TEst Method - ASTM B-117-2019) result 2000 hrs with SS 304 Hex Flange Bolt with serration 5/16 x 3/4 (A/F 13 mm) as per DIN 6921 and SS 304 Hex Flange Nut BSW 5/196 x 18 x 18 x 1.3 wieth serratio as per DIN 6923. (b) Continuous slotted 'C' channelw with ribs to be used of size 450 mm (18") made of Low CArbon Hot Roll Gauge corrected Oil pickled and Drawn (HROP D) Steel (IS 1079) are hot dip Galvanised, Zn Al Flake Coated with material thickness of 3 mm. (c) U Bolt rubber sleeve mounted are made of low Carbon mild steel with Rod diameter 7 mm approx; Zn Al Flake coated with noise absorbing semi tranparent ribbed silicon rubber sleeve: with Hex Flange Nut BSQ 5/16 x 18x18x 13 with serration set as per DIN - 6923 Zn Al Flage coated. Hot dip Galvanising : as per IS 2629 (1985) -610 gm/m2(>85 microns). Used as per MTC confimrs to EN 10204 3.1. Material for One unit : 1. Profile bracket wall distance 75 mm (3")- 02 Nos 2. Continuous slottted C chanbnel of size 450 mm (18") -01 Nos. 3. U bolt runner sleeve mounted for 75 mm (3") PVC pipe dia -01 No and Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2") - 4 Nos . Fixing details : Pipe support c,amping unit to be fized at every 1-2 meter distance in the duct complete all as specified and directed by Engineer - in - Charge.

S&F 110 mm bore PVC (SWR) PVC (SWR) bends with rubber ring any radius complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR)PVC (SWR) branch piece, single (single Y) equal or unequal with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR)PVC (SWR) branch piece, double (double Y) equal or unequal with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) PVC (SWR) junction single, (Single T) equal or unequal with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) PVC (SWR) junction double, (double T), equal or unequal with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) PVC (SWR) couplers with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR) PVC (SWR) reducers with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 110mm bore PVC (SWR)PVC (SWR) vent cowl with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, jointed with solvent fixed to wall or laid in trenches with matching PVC SWR rings including cutting holes and making good the disturbed portion with PCC (1:2:4) type B0 including clamps and bends complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR)PVC (SWR) branch piece, single (single Y) equal or unequal with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) PVC (SWR) junction single, (Single T) equal or unequal with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) PVC (SWR) junction double, (double T), equal or unequal with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) PVC (SWR) couplers with rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR) PVC (SWR) reducerswith rubber ring complete all as specified & directed by Engr-in-Charge.

S&F 75 mm bore PVC (SWR)PVC (SWR) vent cowl with rubber ring complete all as specified & directed by Engr-in-Charge.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cm 1:6 complete all as specified and directed by Engr-in-Charge. Note : Rates of Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises are included in quoted rates.

M&L 450x300x7/ 300x600x7 mm mm thick glazed ceramic coloured tiles as in vertical sufaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles including 10mm backing coat in CM 1:4 complete all as specified and directed by Engr-in-Charge. Note : Rates of Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubish off the premises are included in quoted rates.

S&F in repair, vitreous china squatting pan "ORISSA" pattern white, of size 580x440mm with integral foot rest, CI 'P' trap etc including PVC low level flushing cistern 10 liter capacity, valveless, syphonic action type with float, handle including 32mm dia PVC flush pipe of polyethylene of low or high density, 01 x PVC connection 15 mm dia and 450mm long & bracket etc complete all as specified and directed by Engr-in-Charge.

S&F in repair wall hung WC with UF seat cover, hinges, accessories set size 640x360x765mm white complete, including concealed body flushing cistern with hinging arrangement complete all as specified and directed by Engr-in-Charge.

S&F in repair for vitreous China urinal (back or corner wall type) of size 360x345x570mm complete including providing and fixing assembly plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement ; flush type, grating, CP waste coupling and union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) and including CP urinal spreader for fixing with 15mm dia pipe complete all as specified and directed by Engr-in-Charge.

Supply and fix in repairs vitreous china wash hand basin counter bowl type with green/black granite slab to be cut and polished at site as per requirement, brackets, 32mm bore brass chromium plated waste coupling & 32mm bore low density polythelene (LDPE) flush pipe of pressure 6Kgf/Sqcm (1.00M long,) including 15mm bore 450/600mm length PVC connection with PTMT nuts and fancy type CP mixer, cast copper alloy, with single lever handle, chromium plated, screwed down high pressure, with lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed including Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and directed by Engineer-in-Charge. Note : Granite shall be measured and paid seperately.

M & L granite (of any type) work 16-18 mm thick (table rubbed and polished) in hand wash platforms and like in cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm of screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

S&F premium quality soap dish CP brass 100mm dia (round or oval) fixed to walls or dados. complete all as specified and directed by Engineer - in - Charge.

S&F CP shower rose 125mm size and 15mm dia with 450 mm long CP Arm fixed in repairs complete all as specified and directed by Engineer - in - Charge.

S&F in repair CP Tubular towel rail, 20mm dia, D type, 600mm long between flanges fixed with CP brass screws complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore PVC connections, with PTMT nuts, of length 450/600mm complete all as specified and directed by Engr-in-Charge.

Supply and fix in repairs chromium plated angle stop valves, cast copper alloy 15 mm bore screwed down high pressure with quarter turn type handle for iron pipe or for union complete all as specified and directed by Engr-in-Charge.

S&F in repair concealed chromium plated stop valves, cast copper alloy 15 mm bore screwed down high pressure with quarter turn type for iron pipe or for union and complete all as specified and directed by Engineer-in-Charge.

S&F in repairs 15mm bib taps cast copper alloy, chromium plated fancy type with quarter turn handle screwed down screwed for Iron pipe or for brass ferrule and fixed complete all as specified and directed by Engr-in-Charge.

S&F CP Single lever wall Mixer telephonic with L bend set with long braded hoses with long screwed for iron pipe of 15mm dia, complete all as specified and directed by Engineer - in - Charge.

S&F Grating doom 100mm dia of CP (Minimum weight 90gm) complete all as specified and directed by Engr in Charge

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed by Engr in Charge

Demolition concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) all as specified complete all as specified and directed by Engineer-in-Charge.

M & L for 25 mm thick cement concrete type B-1, 1:2:4 using 20mm graged aggregate as in sub floors, sub bases, floors and pavings etc complete all as specified and directed by Engr in Charge

M & L for 75mm thick cement concrete type C-2, 1:3:6 using 20mm graged aggregate as in plinth protection laid in panels not exc 3 mtr long and joints to be filled with bitumen mastic material complete all as specified and directed by Engr in Charge.

M & L for 75 mm thick cement concrete type B-1, 1:2:4 using 20mm graged aggregate as in sub floors, sub bases, floors, shafts and pavings etc complete all as specified and directed by Engr in Charge

Taking down steel window/ventilators chowkats or frames (without taking off shutters from the frame) not exceeding 1.5 sqm each complete all as specified and directed by Engineer in Charge

M&L anodised aluminium frames for doors, windows with one or moe rebates including jointing cleats for fixing etc. including powder coating minimum thickness of powder coating shall be 50 micron as per the specification) complete all as specified and directed by Engineer-in-Charge.

S&F powder coated aluminium windows and ventilator shutters, side hung type, without sash bars aluminium saction weighing 0.55 kg/RM including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading, screws, powder coated aluminium fitting such as peg stay 150mm long (1 no) hinges type B21 100 mm long (2 No) suitable handle (2 Nos) complete all as specified and directed by Engineer-in-Charge.

S&F powder coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F stainless steel wire cloth cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engr-in-Charge.

Taking down shutters door/window of any description (Wooden/aluminium/ iron/Glass/FRP/PVC/WPC or like) of any material and any type exc 1 Sqm but n exc 2 sqm each and repairing work in all respects, providing handles/hinges or tower bolt as per site requirement and refixing in same opening complete all as specified and directed by Engineer - in - Charge.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 75 x 50 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners deemed to be included in quoted rates.) Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 24mm thick comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. for fixing MosquitoMesh and XTN aluminium mesh combinely panel area of door except stiles and rails to be panelled wire mesh with self tapping rpund headed screws at requrd distance, scres and edge covered with feathered pvc edge beading all around mesh and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer in- Charge. (a) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (b) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x250mm - 1 nos per leaf (d) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 nos per leaf Note : 1: Test certificate of manufacturer to be provided by contractor . 2. Embossing with barcode of manufacturer engraved over each door frame and shutter is manadatory.

M & L for vitrified ceramic tiles double charged, stain free, premium (1st) quality straight edges coloured tiles 10mm thick (square / rectangular) polished, area of each tile not exceeding 0.36 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured epoxy grout to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

PAREEK AND COMPANY (BID ID -3454014)

Dashmesh Construction Company (BID ID -3454692)