Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹27.2 LAccepted-AOC | ₹27.2 L Quoted ₹27.4 L | L1 | Accepted-AOC L1 |
| 2 | L2₹28.2 LRejected-Finance | ₹28.2 L | L2 | Rejected-Finance L2 |
| Sl No | Description | Qty | Unit | VRIDHI ENTERPRISES L2 | Premier Constructions L1 |
|---|---|---|---|---|---|
| 1.00 | Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells cesspits, manholes, pier hole etc. and getting out, complete all as specified. | 32 | Cubic Meter | 250 ₹8,000 | 200 ₹6,400 |
| 2.00 | providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundations, filling and mass concrete etc., complete all as specified and as directed | 51.5 | Cubic Meter | 2,000 ₹1.0 L | 1,500 ₹77,250 |
| 3.00 | Reinforced cement concrete type A-1, 1:2:4 (nominal mix, using 20mm graded crushed stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed | 3.5 | Cubic Metre | 6,500 ₹22,750 | 6,000 ₹21,000 |
| 4.00 | Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in coloumns, pillars etc complete all as specified and directed (reinforcement shall be measured and paid for separately). | 3.5 | Cubic Metre | 6,500 ₹22,750 | 6,000 ₹21,000 |
| 5.00 | Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressumers, lintels over 1.5 metre span and the like complete all as specified and directed (reinforcement shall be measured and paid for separately). | 5.5 | Cubic Metre | 6,500 ₹35,750 | 6,000 ₹33,000 |
| 6.00 | Reinforced cement concrete, 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete, all as specified and directed . | 4.2 | Cubic metre | 6,500 ₹27,300 | 6,000 ₹25,200 |
| 7.00 | Form Work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter to give rough finish to flat surfaces complete all as specified and directed. | 44 | Sqaure Metre | 350 ₹15,400 | 300 ₹13,200 |
| 8.00 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. | 50 | Sqaure Metre | 350 ₹17,500 | 300 ₹15,000 |
| 9.00 | Form Work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and side of RCC / PCC bends in walls , horizontal or sloping and similar work exc 10cm but n.exc 20cm wide complete all as specified and directed. | 27 | Running Meter | 120 ₹3,240 | 200 ₹5,400 |
| 10.00 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and directed. | 1,350 | Kilogram | 85 ₹1.1 L | 80 ₹1.1 L |
Updated dates
Tender Value
₹41.5 L
EMD Value
₹83,000
Closing Date
25 Oct 2025, 6:00 pmClosed
Garrison Engineer
Garrison Engineer Chandimandir panchkula Haryana 134107
GE/CHM-94/2025-2026 ADDN /ALTN TO CIVIL POST OFFICE, P-26, P-414, PROVN OF TOILET BLOCK AND CAR PARKING SHED UNDER AGE B/R III AT CHANDIMANDIR
2025_MES_733042_1
GE/CHM-94/2025-2026
Open Tender
Civil Works
180 days
Chandimandir
Please refer Tender documents.
9 documents required · 9 mandatory
₹500
Garrison Engineer
₹83,000
Yes
3 Jan 2026
27 Sept 2025
27 Oct 2025
27 Sept 2025
25 Oct 2025
11 Oct 2025
Amount
Excavation in trenches in hard/dense soil not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation etc. or for shafts, wells cesspits, manholes, pier hole etc. and getting out, complete all as specified.
providing cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate, as in foundations, filling and mass concrete etc., complete all as specified and as directed
Reinforced cement concrete type A-1, 1:2:4 (nominal mix, using 20mm graded crushed stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed
Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in coloumns, pillars etc complete all as specified and directed (reinforcement shall be measured and paid for separately).
Reinforced cement concrete, type A-1, 1:1½:3 (nominal mix, using 20mm graded crushed stone aggregate) as in beams, cantilevers, bressumers, lintels over 1.5 metre span and the like complete all as specified and directed (reinforcement shall be measured and paid for separately).
Reinforced cement concrete, 1:1½:3 (nominal mix,type A-1, using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams etc, shelves and the like complete, all as specified and directed .
Form Work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter to give rough finish to flat surfaces complete all as specified and directed.
Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.
Form Work to edges of concrete flats, treads, break in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and side of RCC / PCC bends in walls , horizontal or sloping and similar work exc 10cm but n.exc 20cm wide complete all as specified and directed.
Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm complete all as specified and directed.
TMT bars for reinforcement, 6 to 8mm dia & over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.
Brick work with sub class ‘B’ bricks old size bricks, straight or curved on plan exc 6 metre mean radius built in cement mortar 1:6 complete all as specified & directed.
15mm thick rendering in cement mortar 1:4 on brick walls or concrete surface and finished fair and even without using extra cement complete all as specified & directed.
15mm thick rendering in cement mortar 1:6 on brick walls or concrete surface and finished fair and even without using extra cement complete all as specified & directed.
5mm thick rendering in Cement and Sand mortar 1:3 concrete surfaces as in ceiling / chajjas facia at any position finished even and smooth without using extra cement complete all as specified and directedng
Earth filling under floor including watering and consolidation in layers n.exc 25cm thick complete all as specified & directed.
Hard core of broken stone or boulders of gauge exc 63mm, deposited, spread and leveled in layers n.exc. 15cm thick, watered and rolled / rammed to a true surface complete all as specified & directed.
100mm thick PCC 1:4:8 type D-2(using 40mm graded crushed stone aggregate) as in sub base finished even and fair complete all as specified and directed.
Plain cement mortar 1:3:6 (type C-2 using 20mm graded aggregate), 75mm thick as in Plinth protection , finishing cement concrete even and smooth without using extra cement, all as specified. Note : 10mm construction joint will be provided and panel should not be more than 3metre in length and joint filled with filler bitumen and sand in ratio (1:3)
25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base finished fair and even without using extra cement, complete all as specified and directed.
Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm depth , complete all as specified and directed.
Removal of excavated material to distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point , complete all as specified and directed.
Supply only integral water proofing compound complete all as specified & directed.
Framed work such as grill guard bars etc welded to steel frame MS round/square bar conforming to Fe 290 Gde-E 165 complete all as specified and directed.
4mm thick figured glass pin head type ordinary quality any size and in any type of frame and glazing with oil putty in square n.exc 0.5 Sqm in each panes complete all as specified and directed.
Galvanised mild steel wire cloth 0.56 mm nominal dia of wire & avg width of aperture 1.18 mm in fixed with stainless steel wire complete all as specified and directed.
Three coats of white wash on plastered or unplastered ceiling surfaces including preparation of new surfaces complete all as specified and directed
Preparation of new plastered surfaces of walls and applying two coats of cement base paint, complete all as specified and directed.
20mm thick (average thickness) rendering on roof surfaces inclduing flashings and junction of parapets etc finished even and fair in cement mortar 1:4 using water proofing compound as per manufacturer's instruction after brushing cement slurry complete all as specified and directed
Preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.
3mm thick Atactic polypropylene polymer (APP) modified prefabricated five layer water proofing membrane, based polymeric membrane minimum weighing 3.6kg/sqm and reinforced with polyester non woven fabric (weight not less than 150 gm/sqm) laid over a coat of bitumen primer @0.40L/Sqm by same membrane manufacturer of density 0.87 to 0.89 kg/L at 25° C temperature and viscosity 70 to 160 CPS, over primer coat bonding material of blown bitumen 85/25 grade heated to working temperature of 180° C applied @1.2Kg/Sqm. The membrane shall be laid using butane torch and sealing all joints etc after preparing the surface as per standard practice and as per manufacturer instructions and finished, complete all as specified & directed.
20mm thick Granite work (of any type table rubbed and polished) as in lining (veneering to wall) riser, skirting/ dado over and including 15mm thick cement mortar (1:6) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. compelte all as specified and directed.
Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification complete all as specified and directed.
Factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design ,solid PVC foam with homogenous fine cellular structure density 750 having smooth outer integral skin, supplying & fixing in frame at site complete all as specified and directed.
100mm size, butt hinges, medium weight, cold rolled mild steel cmplete all as specified & directed.
150 mm size aluminium anodized, barrel tower bolt of extruded section and fixed complete all as specified and directed.
200 mm size aluminium anodized, barrel tower bolt of extruded section and fixed complete all as specified and directed.
125mm Extruded aluminium alloy handle fabricated type, complete all as specified and directed.
Butt hinges 100mm size, of extruded aluminum alloy with galvanised mild steel hinge pin, anodised, type C-21, complete all as specified and directed.
Aluminum alloy, anodized, sliding door bolt 250mm long hasp , staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminum alloy and fixed, complete all as specified and directed.
Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar (1:3) for concealed pipe etc and making good, cutting not exceeding 10cm girth complete all as specified & directed by Engineer-in-charge.
Non skid, first quality ceramic coloured tiles, 7 to 8 mm thick (square/ rectangular) area or each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 15mm thick screed bed in cement mortar 1:6 complete all as specified and directed.
Glazed ceramic coloured tiles of size 300mmx450mmx7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.
Vitrified ceramic tiles 10mm thick First quality (square / rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over and including 20mm thick screed bed in cement mortar 1:6 complete all as specified and directed.
All as per serial item No 44 herein before but on skirting etc over and including 10mm thick rendering in cement mortar 1:4
15 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors ,complete all as specified and directed.
20 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.
25 mm bore Galvanized Steel tubes, medium grade including all fittings for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed.
PVC (SWR) pipe, 110mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.
PVC (SWR) pipe, 75mm bore, single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and directed.
110mm bore PVC (SWR) bends any radius complete all as specified and directed
75mm bore PVC (SWR) bends any radius complete all as specified and directed
110mm bore PVC (SWR) junction single, (Single T) equal or unequal, with access door complete all as specified and directed.
75mm bore PVC (SWR) junction single, (Single T) equal or unequal, with access door complete all as specified and directed.
Supply and fix 110mm bore PVC (SWR) vent cowl any radiuscomplete all as specified and directed.
PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.
Supply and fix 1000 litres capacity rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) Double layered hoisted and fixed in position, including tank nipple etc, complete all as specified and directed.
Float valve / ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 210gms ) for 20mm bore pipe, complete all as specified and directed.
Vitreous China Wash down water closet (pedestal pattern) , white, (excluding, flushing cistern and flush pipe) with and including PVC seat cover, complete all as specified and directed.
Vitreous china squatting pan "orissa" pattern, size 580 x 440 mm white, with integral foot rest including 'P' or 'S' trap, flush pipe (excluding flushing cistern) including connection to trap and flushing pipe complete all as specified & directed by Engineer-in-charge.
PVC valve less syphonic action type flushing cistern low level white with PVC in let ball valve, float and handle, 10 ltrs capacity and connection to pipes including 32mm dia PVC long bend, set with concrete and making good to floor, complete all as specified & directed.
Towel ring of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 90gms), complete all as specified and directed.
PVC connections 15 mm size with PTMT nuts of length 450 mm , complete all as specified and directed.
PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm bore complete all as specified.
Counter top wash basin, of Size 560x 470x190mm, oval shape, white colour, including waste pipe, CP waste coupling etc fixed in position, complete all as specified and directed.
Wash hand Basin brass Mixer of chromium plated hot and cold water screwed down for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed
Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.
Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both and for iron pipe or for union, suitable for 20mm bore pipe, complete all as specified and directed.
Angular stop cock, fancy type, cast copper alloy chromium plated, screwed down, screwed both and for iron pipe or for union, suitable for 15mm bore pipe, complete all as specified and directed.
Bib taps brass, fancy type, long body with wall flange, chromium plated, cast copper alloy with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule, suitable for 15mm bore pipe, complete all as specified and directed.
Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge
Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.
Door closer hydraulically regulated aluminum (die cast) body, designation No 3, universal type, suitable for door shutters of 701mm to 850mm in width and of weight between 36 to 60 Kg, complete all as specified and directed.
3mm thick aluminium composite panel sheet (ACP) colour as approved by Engr In Charge all as specified and directed.
5.00mm thick ordinary quality tinted glass, fixed to aluminum frame work in panels exc 0.5 Sqm in each pane, complete all as specified & directed.
Taking down cement plaster from brick walls or concrete surfaces including raking out joints, hacking out for key, scrubbing down with water complete all as specified and directed and removing rubbish etc. complete all as specified and directed.
Rendering 15mm thick in Cement and Sand mortar 1:4 over fair faces of brick / concrete ,finished even and smooth without using extra cement, inclunding using water proofing compound complete all as specified. Note : WPC shall be measured and paid separately.
Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheeting 0.50 mm thick any colour having tensile strength 550 Mpa as in roof coverings/cladding to wall, fixed with self tapping screws as specified complete all as specified & directed by Engineer-in-charge.
Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.
Two coats of synthetic enameled paint on steel and iron surfaces over one coat of red oxide primer on surfaces over 10 cm width or girth including preparation of new surfaces complete all as specified & directed.
Factory made coloured chequered cement concrete tiles 250mm x 250mm x 22-25mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry with grey cement with pigment to match the colour of tiles, glossy finish, laid over and including 20mm thick screed bed in cement mortar 1:6, complete all as specified and directed
Surface dressing n.exc 15cm deep in hard dense soil complete all as specified and directed
Hard core of broken stone or boulders of gauge of guage n.exc 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.
Cement concrete type B-0, 1:2:4 using (12.5 mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, parapets and railings upto 60 cm in height, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, including the use of forms or moulds with plain faces complete all as specified and directed. (Cement concrete item shall be reinforced, where ordered. Reinforcement shall be measured and paid separately).
Preparation of new plastered surfaces of any description of wall and applying two coats of oil bound destemper over one coat of interior wall primer including wall care putty (average thickness 1.5 to 2.5mm as required for desired smoothness and leveling of surfaces in two or more layers) and sand papering for making the surfaces even and smooth complete all as specified and directed.
Mild Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified & directed by Engineer-in-Charge
Machine pressed Concrete interlocking paver block, any shape and size conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade with gray cement and no pigment over 25 mm thick sand filling , complete all as specified and directed
Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed.
Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings
Preparation of old previously decorated wall surfaces by booming down, scrapping down smoke soot, moulds efflorescent salts etc and applying two coats of oil bound distemper complete all as specified and directed.
Preparation of old previously decorated wall surfaces by booming down, scrapping down smoke soot, moulds efflorescent salts etc and applying one coat of oil bound distemper complete all as specified and directed.
Demolition of mud in roofs, any thickness incl plastering and leeping etc (whether full thickness removed or only a part thereof) complete all as specified & directed.
PCC 1:2:4 type B-1 (using 20m graded crushed stone aggregate) as in roof padding, finished fair and even without using extra cement, complete all as specified and directed.
Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing, complete all as specified and directed (Note : Colour/design and pattern shall be as decided by the GE)
PVC sheet fillet 35mm wide, 5mm thick for wall paneling inclusive of fixing in to wall to make PVC frame complete all as specified and directed.
Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) With Semi preforated 12mm thick micro tegular edged GRG false ceiling tiles, false ceiling tiles of size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2% humidity resistance of 99% NRO .05 to 0.75 as per IS 8225:1987, Non-combustible as per BS 476 (part4)- 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides ) comprising of main- T runners of size 15 x32 mm of length 3000mm, cross-T of sixe 15 x 32 mm of length 1200mm and secondary intermediate Cross-T of size 15 x 32mm of length 600mm to from grid module of size 600 x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L-shape level adjuster of size 85x25x2mm. Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm centre to centre and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per direction of the Engineer-in-Charge.
Dismantling AC corrugated or semi corrugated sheets as in roof covering incl. ridges & removing from site complete all as specified and directed
Demolition of plain cement concrete in ground floor and paving n.exc 15cm thickness below or above ground level complete all as specified and directed.
Cutting openings, through brick walls built in cement morat for door, windowand other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish notexc. 50m complete all as specified and directed.
Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.
Material and labour for point wiring with approved colour code multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade, two run of single core cable for phase & neutral and one run of single core multi stranded copper conductor, PVC insulated and unsheathed FRLSH cable of size 1.5 Sqmm ,1100 volts grade for earth continuity conductor to common earth and connected to earth dolly in and including new concealed PVC conduit terminated on and including new modular sunken box and suitable size of frame, cover for mounting switch, socket and regulator fixed on surface flush with wall , comprising of One light /bell/buzzer point controlled by one switch or one fan point controlled by one switch &fan regulator, complete all as specified and directed. Note : Unit rate is inclusive of making good the disturbed surfaces by provding by wall putty/POP after mason work and finshing to match the original and nothing extra shall be paid on this account. Note :Unit rate is inclusive of cutting chases in wall /foor/PCC and making good the disturbed surfaces to match the original and nothing extra shall be paid on this account.
All as per serial item 102 herein before but for socket outlet 3 pin 6Amps on same board complete all as specified and directed
All as per serial item 102 herein before but for socket outlet 3 pin 6 Amps on independent board complete all as specified and directed
All as per serial item 102 herein before but One socket outlet three pin ,6/16 Amp, independent board, with 2.5 Sqmm (nominal area ) FRLSH cable & 2.5 Sqmm (nominal area) cable as earth continuity conductor
Switch modular type (ISI marked), single pole, one way 6 Amps, one module (ISI marked), complete all as specified & directed.
Switch modular type (ISI marked), single pole, one way 16 Amps, one module (ISI marked), complete all as specified & directed.
Socket shutters outlet 2/3 pin 6 Amp modular type multi purpose two module (ISI marked), complete all as specified & directed.
Socket shutters outlet 2 in 1 pin 6/16 Amp modular type multi purpose combined 2 module (ISI marked), complete all as specified & directed.
Modular switch type stepped fan regulator, single pole, 230 volt two module complete all as specified and directed.
Ceiling rose, PVC or polycarbonate of size 65mmx50mm three terminals (ISI marked) all as specified and directed by Engineer-in-charge.
Lamp holder, PVC/Polycarbonate type with back plate modular type fixed on wall suitable for batten fitting ,complete all as specified and directed.
LED lamp 9 watts, B-22 type complete all as specified .
LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, fixed as in repair complete all as specified and directed.
LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size, fixed as in repair complete all as specified and directed.
LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete complete all as specified and directed.
LED lights fitting 1x 20W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete fixed as in repair complete all as specified and directed.
LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.
LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size fixed as in repair complete all as specified and directed.
Disconnecting the power supply and taking down carefully by unscrewing from boards fittings and fixtures such as DBs, Junction Box, Panels of any size complete with all MCCB's ,MCB's etc and removing from site, Complete all as specified and directed .
MCB DB, IP 43 protection, powder coated double door with locking arrangement suitable for surface and flush mounting, 12 way SPN with 200 Amps busbar 240V completed all as specified and directed.
MCB ,SP , 240 volt, 6Amps to 32Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed
MCB, SPN, 240 volt, 40 to 63Amps, 10 KA , 'C' series including connection with suitable size aluminium / copper lugs complete all as specified and directed
Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) and provision of flexible copper cable 3 core from ceiling rose to fan complete all as specified and directed.
Taking down carefully old copper or aluminium sub main wiring of any Nos of wiring and size with earth wire on wooden batten/ surface conduit/ casing- capping complete with its all accessories and making good disturbed surfaces of wall , floors etc complete all as specified and directed.
Sub main wiring with two single core FRLSH PVC insulated and unsheathed cable with copper conductor of size 6 Sqmm (nominal area), 1100 Volt grade(with approved colour coding as per IS) with and including continuous earth wire of size 6 Sqmm PVC insulated and unsheathed FRLSH multi stranded copper conductor 1100 volts grade , and connected to main board drawing through PVC concealed conduit 25mm size(minimum size), cutting chases in walls for PVC concealed conduit and making good the disturbed surfaces by providing by wall putty/POP after mason work and finshing to match the original surfaces and nothing extra shall be paid on this account all as specified and directed. NOTE: (i) Two runs of cable, one run of earth wire shall be considered as one running metre (ii) colour code shall be Red for phase, Black for neutral and green for earth
Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe of 20mm dia, GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete , all as specified and directed.
Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.00mm burried directly in ground vertically to a depth not less than 2.25m below normal ground level, with top edge of the plate not less than 1.5m below normal ground level, earth plate surrounded by 15cm thick and packed alternate layers of charcoal dust and common salt, connected with and including earth lead of GI wire 4mm dia (8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron or thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron pipe light grade 15mm dia bore including watering pipe of 20mm dia, GI light grade (ISI marked) with funnel and wire mesh, including all necessary excavation and earth work, PCC chamber in plain cement concrete (1:3:6) type C-1 and pit cover of presast RCC with MS frame etc and all as shown in electrical plate No 3 of MES Sch Part-I (2009), complete including dismantling of old earthing, all as specified and directed.
LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver,including lamp bracket upto 1.5metre length as per suitable for fitting including clamp with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection, complete all as specified and directed.
LED panel recess mounted ultra slim 2'x2' - 36 watts ultra slim (cool day) ceiling light, aluminum extruded housing with milky diffuser, heat exchanger unit, LED driver, surge protection complete suitable for perfect lighting cutting hole of required size in POP/false ceiling making good disturbed complee all as specified and directed.
LED panel recess mounted ultra slim 2'x2' - 36 watts ultra slim (cool day) ceiling light, aluminum extruded housing with milky diffuser, heat exchanger unit, LED driver, surge protection complete suitable for perfect lighting cutting hole of required size in POP/false ceiling making good disturbed including taking down any type ceiling fitting complee all as specified and directed.
Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm and provision of flexible copper cable 3 core from ceiling rose to exhaust fan complete all as specified and directed.
XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sqmm, 2 core, laid in trenches , sleeving through pipes of fixed on poles & wall or laid under floors inlcuding jointing with suitable size of alumunium lugs as specified and directed.
ABS plastic1800W White Crescent Wall Mounting hand dryer machine (ISI Marked) suitable for bathroom compelte all as specified and directed.
VRIDHI ENTERPRISES (BID ID -3458909)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.34 MB
BOQ_820763.xls
BOQ • 0.45 MB
Tenderpages94.pdf
Tender Documents • 1.18 MB
Download all tender documents and submit your bid