Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹3.2 LAccepted-AOC VILLAGE TAPARIYAN BABINA CANTT BABINA JHANSI UP 284401 | BABINA | JHANSI | UP | 284401 | L1 | Accepted-AOC Accepted | |
| 2 | L2₹4.5 L+₹1.2 L (35.7%)Rejected-AOC CIVIL LINE MATATILA ROAD TALBEHAT DISTT LALITPUR U P | TALBEHAT | LALITPUR | U P | L2 | Rejected-AOC Rejected | |
| 3 | L3₹4.6 L+₹1.3 L (39.7%)Rejected-AOC | L3 | Rejected-AOC Rejected |
Tender Value
₹5 L
EMD Value
₹10,000
Closing Date
31 Jan 2020, 6:00 pmClosed
AGE I TALBEHAT
AGE I TALBEHAT LAKE VIEW CAMP TALBEHAT PIN-284125
REPAIR/SERVICES OF DG SETS, PUMP SETS AND PANEL BOARDS OF MAIN WATER POINT AND 9A PUMP HOUSE AT MIL STN TALBEHAT
2020_MES_313501_1
AGE(I)/TBT/TOK-49/2019-20
Open Tender
Miscellaneous Works
Item Rate
180 days
AGE I TALBEHAT
Please refer Tender documents.
7 documents required · 7 mandatory
₹500
AGE I TALBEHAT
₹10,000
Yes
15 Feb 2020
10 Jan 2020
5 Feb 2020
10 Jan 2020
31 Jan 2020
20 Jan 2020
Amount
Servicing of 200 KVA DG set including replacement of gasket tappet cover, oil and fuel filter elements, adjustment of tappet of 6 cylinders engine, drain out the old engine oil clean the oil sump and refilling with the required quantity of new oil, Checking of fan hub, including externally cleaned complete all as specified and directed by Engineer- in-Charge. Note:- Spares parts/New engine oil shall be measured and paid separately under relevant items Make of Engine:- Kirloskar/Cummins
Servicing of DG Set (any capacity of 25 KVA to 82.5 KVA) including replacement of gasket tappet cover, oil and fuel filter elements, adjustment of tappet of 6 cylinders engine, drain out the old engine oil clean the oil sump and refilling with the required quantity of new oil, Checking of fan hub, including externally cleaned complete all as specified and directed by Engineer- in-Charge. Note:- Spares parts/New engine oil shall be measured and paid separately under relevant items Make of Engine:- Kirloskar/Cummins
Overhauling of water pump assembly and radiator complete including material and labour for impeller, shaft seal bearing, gaskets washers and rubber hose complete of the following DG Sets: 25/40/50/62.5/82.5/200 KVA complete all as specified and directed by Engineer- in-Charge. Make:- kirloskar/cumins/Ashok layland
Supplying & Fixing Solenoid Control Switch 12 Volt DC suitable for 50/25KVA DG Set complete all as specified and directed by Engineer- in-Charge.
S&F the following items in replacement DG set 25/40/50/62.5/82.5 KVA Make :- Ashok Layland/Cummins/power system India
Assembly for filter cartridge with gasket bolt washers complete all as specified and directed by Engineer- in-Charge.
Fuel filter element complete all as specified and directed by Engineer- in-Charge. Make:- MICO
Fuel line assy (Fuel pump to filter) complete all as specified and directed by Engineer- in-Charge.
Fuel line assy (Filter out let to FIP) complete all as specified and directed by Engineer- in-Charge.
starting push button of exiting type complete all as specified and directed by Engineer- in-Charge.
Water temp gauge 12 V complete all as specified and directed by Engineer- in-Charge.
Oil pressure gauge complete all as specified and directed by Engineer- in-Charge.
Key switch with all accessories complete all as specified and directed by Engineer- in-Charge.
Rubber hose pipe with jubilee clip complete all as specified and directed by Engineer- in-Charge.
Fly wheel Ring /starting ring complete all as specified and directed by Engineer- in-Charge.
Vibration pad complete all as specified and directed by Engineer- in-Charge. Make:- As per existing
Coolant container of 1 litre capacity complete all as specified and directed by Engineer- in-Charge.
Disconnecting/ de-coupling alternator opening rotor, dusting, cleaning all components lubricating with specified grade grease, warnishing, opening, reassembling of coupling, reconnection including material and labour necessary lugs and satisfactory testing of following DG sets:-
200 KVA complete all as specified and directed by Engineer- in-Charge.
82.5 KVA complete all as specified and directed by Engineer- in-Charge.
62.5 KVA complete all as specified and directed by Engineer- in-Charge.
50 KVA complete all as specified and directed by Engineer- in-Charge.
40 KVA complete all as specified and directed by Engineer- in-Charge.
25 KVA complete all as specified and directed by Engineer- in-Charge.
Taking out defective Self-starter of DG set, penning complete and replacement of worn out parts like carbon bush, shaft bush, servicing, dusting, greasing and refitting and testing complete of following DG sets:-
200 KVA complete all as specified and directed by Engineer- in-Charge.
82.5 KVA complete all as specified and directed by Engineer- in-Charge.
62.5 KVA complete all as specified and directed by Engineer- in-Charge.
50 KVA complete all as specified and directed by Engineer- in-Charge.
40 KVA complete all as specified and directed by Engineer- in-Charge.
25 KVA complete all as specified and directed by Engineer- in-Charge.
Supply and fixing in repair AVR unit /CVR –II for 50 KVA DG Set complete all as specified and directed by Engineer- in-Charge. Make : Kirloskar/Cummins
Supply and fixing DC Source of 12 V 130 AH complete all as specified and directed by Engineer- in-Charge. Make:- Exide/Amaron
Supply and fixing DC Source of 12 V 150 AH complete all as specified and directed by Engineer- in-Charge. Make:- Exide/Amaron
Supply and filling engine oil (K-Oil) grade 20 W 40 complete all as specified and directed by Engineer- in-Charge. Make:- kirloskar/castrol
Disconnection and taking out the submersible pump set from bore and Rewinding of submersible motor of cap 2 HP with super enamelled copper wire of existing gauge including of slots ,providing insulating paper & varnish complete suitable for under mentioned capacity of motor & proper connection & testing to the satisfaction of Engineer -in-charge.
Dismantling of star delta starters suitable for 75 HP Motor for Repair/ Replacement unserviceable parts such as ,contactor, Time relay , three-pole thermal overcurrent release ,Automatic cut outs for main circuit, Automatic cut-out for control circuit ,coil, buttons , over load relay, junction parts of starter complete all as specified and directed by Engineer- in-Charge.
Dismantling of DOL starters suitable for 7.5 HP Motor for Repair/ Replacement unserviceable parts such as ,contactor, Time relay , three-pole thermal overcurrent release ,Automatic cut outs for main circuit, Automatic cut-out for control circuit ,coil, buttons , over load relay, junction parts of starter complete all as specified and directed by Engineer- in-Charge.
Rewinding of centrifugal pump set motor of 75 HP with super enamelled copper wire of existing gauge including of slots providing insulating paper and varnish complete suitable for under mentioned capacity of motor and proper connection and testing to the satisfaction of Engineer-in-charge.
Disconnecting, isolating and dismantling of pump set with motor model DSM-5B / DSM100/36 cap 75 HP (Make: Kirloskar) shifting local workshop for repair including servicing, re assembling re-fixing in position and proper alignment after replacing of defective spare parts, painting with two coats of synthetic enamel paint of approved shade testing on no load/full load complete all as specified and directed by Engineer- in-Charge.
Supply and fixing following items of pump set of make as per existing:-
Wear ring complete all as specified and directed by Engineer- in-Charge.
Interstage ring complete all as specified and directed by Engineer- in-Charge.
Cartridge for bearing double end complete all as specified and directed by Engineer- in-Charge.
Cartridge for bearing not double end complete all as specified and directed by Engineer- in-Charge.
Nut bolts with rubber bush including shaft coupling flexible joy type K-276 complete all as specified and directed by Engineer- in-Charge.
Shaft/sleeve under stuffing box DE/NDE complete all as specified and directed by Engineer- in-Charge.
Bearing 21309 NDE complete all as specified and directed by Engineer- in-Charge.
Bearing 3309 DE complete all as specified and directed by Engineer- in-Charge. Make : NBC/SKF
Impeller key complete all as specified and directed by Engineer- in-Charge.
Latern ring complete all as specified and directed by Engineer- in-Charge.
Coupling key complete all as specified and directed by Engineer- in-Charge.
Ball bearing 6311complete all as specified and directed by Engineer- in-Charge. Make:- NBC/SKF
Ball bearing N-314 complete all as specified and directed by Engineer- in-Charge. Make:- NBC/SKF
High tensile steel pump shaft complete all as specified and directed by Engineer- in-Charge.
Impeller for pump model DSM 100/36- DSM-5B complete all as specified and directed by Engineer- in-Charge.
Dismantling of Decrine Chlorine dosing pump for Repair/servicing/ replacement of unserviceable following parts complete all as specified and directed by Engineer- in-Charge.
Replacement of the following parts for dosing pump:-
Injection check valve 3/8'' -MALT002 complete all as specified and directed by Engineer- in-Charge.
Check valve Duckbill only MCCVDBO complete all as specified and directed by Engineer- in-Charge.
Single head feed rate control with shaft FC5040D complete all as specified and directed by Engineer- in-Charge.
Dismantling of old US Spares(MCCB, Change over switch, of existing Panel Board of main pump house for replacement / Renewal of spares complete all as specified and directed by Engineer- in-Charge.
Supply and fix the following accessories:-
MCCB (250 Amp-25 KA) Adjustable type - 03 Nos complete all as specified and directed by Engineer- in-Charge.
Change over switch 250 Amps, open execution typ 415 volts , 50 Hzs-01 Nos complete all as specified and directed by Engineer- in-Charge.
Voltmeter 0-500 Volts Digital type complete all as specified and directed by Engineer- in-Charge.
Amp meter 0-100 Amps Digital type complete all as specified and directed by Engineer- in-Charge.
Internal wiring of LT panel board/ feeder pillar box with copper conductor of suitable size complete with colour coding and fixing with ties and lugs complete all as specified and directed by Engineer- in-Charge.
Dismantling of star delta Soft starters EMX -3 Series suitable for 75 HP Motor for Repair/ Replacement unserviceable parts such as ,contactor, Time relay , three-pole thermal overcurrent release ,Automatic cut outs for main circuit, Automatic cut-out for control circuit ,coil, buttons , over load relay, cord etc. junction parts of soft starter complete all as specified and directed by Engineer- in-Charge.
Supply and fixing of copper conductor of size 25 sq mm single core multistrand complete with lugs and necessary jointing materials for connections complete For 75 HP Motors complete all as specified and directed by Engineer- in-Charge.
HARNAM SINGH ANIL SINGH
M/S National Automobiles
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .