ADDN/ALTN AND SPECIAL REPAIRS TO CERTAIN MD ACCN AT RANGAPAHAR MIL STN

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing unserviceable tiles and rubbish off the premises complete all as specified and as directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Dismantling wall and ceiling boards (AC, fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and as directed.

Demolition of brick work of any description and in any position built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in any position not otherwise specifically provided for and removal of rubbish from the site complete all as specified and as directed.

Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc. complete all as specified and as directed.

Dismantling of Mild Steel or Wrought Iron Work of any description not otherwise provided for complete all as specified and as directed.

Taking down chowkat with shutter without taking off shutter from the frame n.exc 1.50 Sqm each complete all as specified and as directed.

Taking down chowkat with shutter without taking off shutter from the frame exc 1.5 Sqm but n.exc 4.0 Sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1.00 Sqm but n. exc. 2.00 Sqm each complete all as specified and as directed.

Supply and fixing in repair Rotational Moulded Polythene [HDPE] triple layered Water Tanks, ISI Marked, Cylindrical & Vertical Type 750 Litres Capacity hoisted and fixed in position including provision of 20 mm and 25mm dia spouts for connecting inlet, outlet, over flow and washout pipes, Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 20mm - 210 Grams] etc. complete all as specified and as directed.

Supply and fixing in repair Rotational Moulded Polythene [HDPE] triple layered Water Tanks, ISI Marked, Cylindrical & Vertical Type 1000 Litres Capacity hoisted and fixed in position including provision of 20mm and 25mm dia spouts for connecting inlet, outlet, over flow and washout pipes, Ball Valves, 20 mm Bore, high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe [Minimum Weight 20mm - 210 Grams] etc. complete all as specified and as directed.

M & L for Use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges with rough finished surfaces of concrete flat complete all as specified and as directed.

M & L for RCC, Nominal Mix, type B-1 1:1.5:3 using 20mm graded stone aggregate as in Chajjas complete all as specified and as directed.

Material and labour for mild steel TMT bars 10mm dia and over, cut to length bent to shape required, including cranking bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and as directed.

M & L for Mild steel TMT bars 5mm dia. and over upto and including 10mm dia in stirrups, spacers and binders and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed.

Material and labour for PCC 1:5:10 type E2 (Using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

Material & Labour for 25 mm thick PCC 1:2:4, Type B-1 using 20mm graded aggregate as in sub base of flooring, surface finished even and rough complete all as specified and as directed.

Material & Labour for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE/AGE(I).

Material & Labour for Vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, light shade, area of each tiles not exceeding 0.36 sqm, as on skirting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over and including rendering of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE/AGE(I).

Material & Labour for joint free non skid ceramic coloured tiles 7 to 8mm thick (square /rectangular) of premium quality, area of each tile exceeding 0.11 sqm but not exc 0.18sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE/AGE(I).

Material & Labour for joint free glazed ceramic coloured tiles 350 x 450 x 7 mm thick of premium quality on skirting/dado, set & jointed in neat cement slurry & pointed with white/coloured to match over and including rendering of 10mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE/AGE(I).

Material & Labour for preparation of concrete surfaces and applying cement plaster coat laid to slope average thickness 20mm in CM 1:3 mixed with liquid WPC @ 200ml per bag of cement, surfaces finished even and fair and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m complete all as specified and as directed. Note: WPC will be measured and paid separately.

M & L for cleaning plastered surfaces of sunken floor to receive the water proofing membrane, applying a coat of bituminous primer @ 0.30 ltrs per sqm and applying a layers of APP based polymeric membrane, 3mm thick (minimum) weight 3.00 Kg/sqm reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) shall be applied over Bituminous primer (Application of polymeric memberane shall be by torch application, over laps shall be minimum 100mm on the transverse direction & 75 mm on the longtudinal direction) polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of wall and shall be finished by membrane flashing, coved fillet in PCC (1:2:4) type B-0 of radius 75 mm shall be provided at the junction of floor & wall surfaces & the surfaces & applying one coat of aluminium paint over the APP nmodified membrane @ 0.10 kg/sqm complete all as specified and as directed. complete all as specified and as directed. Note: Cutting of grooves will be carried out by using mechanical means like groove cutter/wall chaser.

Material & Labour for preparation of concrete surfaces and applying cement plaster coat laid to slope average thickness 10mm in CM 1:4 mixed with liquid WPC @ 200ml per bag of cement, surfaces finished even and fair complete all as specified and as directed. Note: WPC will be measured and paid separately.

M & L for cleaning plastered surfaces and applying a coat of bituminous primer @ 0.30 ltrs per sqm and applying a layers of APP based polymeric membrane, 3mm thick (minimum) weight 3.00 Kg/sqm reinforced with polyster non woven fabric (weighing not less than 150 gms/sqm) shall be applied over Bituminous primer (Application of polymeric memberane shall be by torch application, over laps shall be minimum 100mm on the transverse direction & 75 mm on the longtudinal direction) polymeric membrane shall be taken to a height of 60 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by membrane flashing, coved fillet in PCC (1:2:4) type B-0 of radius 75 mm shall be provided at the junction of roof & other vertical surfaces & surfaces shall be painted with hot paving bitumen of penetration value 85/25 conforming to IS 73 @ 1.20 kg/sqm & applying one coat of aluminium paint over the APP nmodified membrane @ 0.11 kg/sqm complete all as specified and as directed. Note: Cutting of grooves will be carried out by using mechanical means like groove cutter/wall chaser.

M&L for brushing neat cement slurry with 3Kg cement per Sqm complete all as specified and directed.

M&L for 40 mm thick ,PCC(1:2:4), type B-0, using 12.50 mm graded aggregate as in slope correction layer over RCC slab finished even and smooth without using extra cement complete all as specified and as directed.

M&L for cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 tro ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc and making good, cutting not exc. 10 cm girth complete all as specified and directed.

Supply and fix 105x60mm size pressed steel 1.25mm thick frames for door with one or more rebates including necessary fixing lugs, hinges,lock strike plate, etc, complete all as specified and as directed.

Supply and fix 125x60mm size pressed steel 1.25mm thick frames for door with double rebates including necessary fixing lugs, hinges,lock strike plate, etc, complete all as specified and as directed.

Supply and fixing well-seasoned 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

Supply and fixing for 35mm thick factory made flush door shutters solid core construction with block board core and ply wood face panels commercial type on both faces complete all as specified and as directed.

Material and labour for 0.9 mm thick Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and as directed.

Supply and fixing in repairs 18 / 19 mm thick prelaminated medium density fibre board, exterior grade, prelaminated both side with decorative choice lamination fixed with stainless steel screw to timber framework complete all as specified and directed.

Material and labour for 35mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Sec-tion 8, clause 8.24 (a) complete all as specified and as directed.

Supply and fixing stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 and fixed with tinned tacks or staples or wooden beads complete all as specified and as directed.

S&F powder coated Anodised aluminium frame (minimum thickness of powder coating 50 micron) for sliding windows and ventilators with or without rebates including joining cleats for fixing etc. complete all as specified and as directed.

S & F Aluminium Powder Coated Three Track window (2 glazed & one gauze shutter and aluminium sections weighing not less than 0.55kg/m for shutter) including necessary Joining Cleats, Glazing Clips, Neoprene Rubber Packing, Powder Coated Aluminium Snap Beading, Screws, Powder Coated Aluminium Fittings such as Locking Arrangement, rollers complete all as specified . Note: (a)The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I. [b] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing, fittings such as locks etc. [c] Glass and wire mesh shall be measured and paid saperately.

Supply and fixing Aluminium anodised ventilator with sliding type louvers and provision for fixing exhaust fan and fixed type glazing complete all as specified and as directed. Note: (a)The size of aluminium sections shall be all as specified in relevant IS code and MES Schedule Part - I. [b] Unit rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing etc. [c] Glass and wire mesh shall be measured and paid saperately.

Supply and fixing Powder Coated Aluminium Deco Grill C channel on top and bottom fixed independently outside of sliding windows complete all as specified and as directed. Note: Weight of deco grills shall not be less than 1.5 Kg/sqm.

Material and labour for preparation of new or previously untreated wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded decorative coloured laminates PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and decorative coloured laminates PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail or bottom rail ; panelling of decorative coloured laminates PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC laminated sheet beeding, and joined together with solvent cement, supplying and fixing in the frame at the site as per specification complete all as specified and as directed.

Supply and fixing 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed.

Supply and fixing 150mm long aluminium alloy, anodized, sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts,of extruded sections or cast aluminium alloy complete all as specified and as directed.

Supply and fixing 100 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

Supply and fixing 75 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

Supply and fixing 150mm long extruded aluminium alloy bow handles, cast type, anodised complete all as specified and as directed.

Supply and fixing 125mm long extruded aluminium alloy bow handles, cast type, anodised complete all as specified and as directed.

Supply and fixing 75mm long extruded aluminium alloy bow handles, cast type, anodised complete all as specified and as directed.

Supply and fixing aluminium anodized, barrel tower bolts, 100mm long of extruded section complete all as specified and as directed.

Supply and fixing aluminium anodized, barrel tower bolts, 200mm long of extruded section complete all as specified and as directed.

Material and labour for Timber framed and fixed clean sawn 2nd class hard-wood in scantling fixed complete all as specified and as directed.

Supply & Fixing Hasp and Staple, safety type of aluminium anodised including bolt to hinge plate, fixed with screws of 75mm size complete all as specified and as directed.

Supply & Fixing Continuous [Piano] Hinges, Mild Steel, Bright finish or Electrogalvanised and width of Flaps 40mm [When Open] complete all as specified and as directed.

Supply & Fixing mild steel 200 mm long, Ordinary Rat Rail Rod Pattern springs including roller and roller plate complete all as specified and as directed.

Material and labour for brick work with sub class `B` bricks, old size, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 6mm dia bars at every fourth course of brick work complete all as specified and as directed.

Material and labour for brick work with old bricks obtained from demolition of brick work vide serial item No. 5, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) including cleaning and removing of mortar from old bricks complete all as specified and as directed.

Materials and labour for 10 mm thick rendering on other than fair faces of brick work or concrete surface in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.

Materials and labour for 15 mm thick rendering on fair faces of brick work, mixed with liquid WPC @ 200ml per bag of cement content in cement mortar (1:4) on wall and finished the surfaces even and smooth without using extra cement complete all as specified and as directed. Note: WPC shall be measured and paid seperately.

Materials and labour for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Materials and labour for complete removal of existing treatment from old decorated plastered surface of wall and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick cement based wall care putty after preparation of surface complete all as specified and as directed.

Materials and labour for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick cement based wall care puttycomplete all as specified and as directed.

Materials and labour for complete removal of existing treatment from old decorated plastered surface of ceiling and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick cement based wall care putty after preparation of surface complete all as specified and as directed.

Materials and labour for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper over a coat of primer over 1.5mm thick cement based wall care putty complete all as specified and as directed.

Material and labour for complete removal of existing treatment from old decorated surface, preparation of old plastered surfaces of wall and applying two coats of weather coat exterior emulsion paint over a coat of alkali resistant primer complete all as specified and as directed.

Material and labour for preparation of newly plastered surfaces of wall and applying two coats of weather coat exterior emulsion paint over a coat of alkali resistant primer complete all as specified and as directed.

M & L for preparation of old plastered or unplastered surfaces including brooming down or steel wire brushing and applying one coat of white wash on ceiling complete all as specified and as directed.

Taking up or down steel tubing 15mm bore and connections complete all as specified and directed.

Taking up or down steel tubing 20mm bore and connections complete all as specified and directed.

Taking up or down steel tubing 25mm bore and connections complete all as specified and directed.

S & F in repairs Vitreous China Wash Down Water Closet [Pedestal pattern], White, including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

Suppy & fixing as in repair Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including 32mm dia brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe with PTMT check nut and union etc. complete all as specified and as directed.

Suppy & fixing as in repair 10 litre capacity low level twin flush PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections complete all as specified and as directed.

Supply and fixing 25 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

Supply and fixing 20 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

Supply and fixing 16 mm outer dia CPVC Pipes SDR 11 & Plain CPVC SDR 11 Fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing complete all as specified and as directed.

Supply and fixing in repair 15mm dia PVC connection pipe 450mm long with PTMT nuts complete all as specified and as directed.

Supply and fixing in repairs Pillar Tap with areator, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed. Make: Cat Part No. QT F2006101 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Bib Tap with wall flange and areator, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type, screwed down for iron pipe and fixed etc complete all as specified and as directed. Make: Cat Part No. QT F2006151 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Two way Bib Tap with wall flange and areator, cast copper alloy, 15 mm dia, Chromium Plated, Fancy Type, screwed down for iron pipe and fixed etc complete all as specified and as directed. Make: Cat Part No. QT F2006163 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Stop Valves, 15 mm bore dia of pipe, Fancy type, Chromium Plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed.

Supply and fixing in repairs Angle Stop Valves, 15 mm bore dia of pipe, Fancy type, Chromium Plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed. Make: Cat Part No. QT F2006201 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Brass Chromium Plated Toilet Paper Holder with brass screws complete all as specified and as directed. Make: Cat Part No. F 5007109 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Soap Dish, Stainless steel of approximate size 160 x 160 x 90 mm with brass screws complete all as specified and as directed. Make: Cat Part No. F 5003106 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Health Faucet with 1 m long flexible tube, wall hook, non return valve complete all as specified and as directed. Make: Cat Part No. F 8030102 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Brass Chromium Plated Tubular Towel Rail, 20mm dia, D Type, 600 mm long between flanges complete all as specified and as directed. Make: Cat Part No. F 5007103 of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repairs Brass Chromium Plated overhead 15mm bore Shower Rose of size 125mm with 3 flow swivel joints including shower arm fixing to steel pipes or union complete all as specified and as directed. Make: Cat Part No. F 7020305 for Shower Rose and F 7040104 for Shower Arm of CERA or equivalent makes as specified in Particlular Specification.

Supply and fixing in repair Wall mixer, 15mm dia,cast copper alloy, chromium plated for mixing Hot and Cold water screwed down for iron pipe and fixed complete all as specified and as directed.

Supply only Liquid water proofing compound (WPC) of best quality (ISI marked) complete all as specified and as directed.

Supply and fixing in repair for 110 mm dia PVC (SWR) pipes double socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

Supply and fixing in repair for 75 mm dia PVC (SWR) pipes double socketed, in any length with rubber ring joints, fixed to wall complete all as specified and directed.

Supply and fixing PVC (SWR) Nhani Trap of 75mm outlet with SS cover grating complete all as specified and directed.

Supply and fixing 110 mm bore PVC (SWR) bends any radius complete all as specified and directed.

Supply and fixing 75 mm bore PVC (SWR) bends any radius complete all as specified and directed.

Supply and fixing Salt Glazed Stoneware Gully Trap, Square or Round mouthed, type "P" of size 150x150mm including jointing and set in cement mortar complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C0 (using 10 mm graded stone aggregate) as in Post holes, mass concrete, filling in steel frame etc complete all as specified and as directed.

Material and labour for cutting holes into or through cement concrete Slabs, Chajjas, Beams, Columns etc. reinforced or otherwise for superficial area exceeding 100 Sq.cm and not exceeding 250 Sq.cm complete all as specified and as directed. Note- Cutting of holes will be carried out by using mechanical means like drilling machine.

Material and labour for Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement for inserting prepainted galvalume sheet complete all as specified and as directed . Note- Cutting of grooves will be carried out by using mechanical means like groove cutter/wall chaser.

Material and labour for filleting in any position and to any shape, sectional area exc 25 but n exc 50 sqcm in cement mortar 1:3 including all mitres, stops, etc complete all as specified and as directed .

Supply and fixing steel work in tubular trusses i.e truss bottom, top bend, sides, side supports, holding plates, posts and base plate etc. including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 etc complete all as specified and as directed .

Supply and fixing Rolled mild steel joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe 410-W (Gde-E- 250) quality- B etc complete all as specified and as directed .

Supply and fixing rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde E-250) quality- B complete all as specified and as directed.

Supply and fixing wind ties for roof including securing bolts, posts and struts including all necessary drilling bolt or reveting etc. and similar works conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based corrugated / semi corrugated trapezoidal profie sheet steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed.

Supply and fixing 0.50mm thick pre-painted galvalume aluminium Zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as per manufacturer instruction complete all as specified and as directed.

Material and labour for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Material and labour for preparation of new or previously untreated steel or iron surfaces of any description n.exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Supply and fixing 0.56 mm thick Plain Aluminium Sheet Alloy 31000 H4 in Ridges, Hips, Valley Gutter, drip and straight flashing complete all as specified and as directed. Note- measured as the minimum rectangle from which the pieces can be cut.

Supply and fixing MS machine made screw bolts with hexagonal or square head one end and screwed other or screwed both ends, fitted with washers and one hexagonal or square nut exceeding 10 cm long and not exceeding 15 cm long, dia of neck exceeding 16 mm but not exceeding 20 mm complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

Supply and fixing Harrison Rails [Curtain Rails], Anodised Aluminium, 20 mm dia with fixing brackets, stops, rollers etc complete all as specified and as directed.

Supplying and laying in repair GI tubing of 40 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc laid in floors/ fixed on walls including testing complete all as specified and as directed.

Supply and fixing in repair 40mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

Material and labour for precast Cement Concrete tiles of size 250 x 250 x 22mm thick as in floor, set and jointed in neat cement slurry and pointed with cement laid over and including 20mm thick screed bed in CM (1:4) complete all as specified and as directed.

Supply and fixing in repair of Stainless steel kitchen sink with drainage board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe overall size 915mm x 460mm and bowl size 410mm x 330mmx 160mm depth complete all as specified and as directed .

Supply and fixing in repair stainless steel (conforming to AISI-304 grade) plate rack of overall size 790mm x 610mm x 220mm or equivalent made of 1mm thick stainless steel sheet fixed on wall with 4 Nos, 50mm long screws & PVC rawl plug complete all as specified and as directed

Supply and fixing 4 mm thick size 595 x 595 mm HPSC (High pressure Steam Cured) pre-primefered self embossed texture designer board E-board classic to be fixed with and including galvanized iron grid / section of size 600 mm x 600 mm with main runner 38 x 24 x 0.90mm thick, cross tee 28.6 x 24 x 0.9 mm and wall angle 19 x 19 x 0.9 mm duly suspended with 2 mm dia GI wire hanger 1200 mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including providing provisions for light fixtures of any size complete all as specified and directed.

Material and labour for PCC 1:3:6 type C1 (Using 20 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and as directed.

Material and labour for 20-25 mm thick machine cut kota stone slab shall be laid on floor, laid and jointed with grey cement slurry mixed with pigment to match the colour / shade of the slab over and including 20mm thick screed bed / bedding layer in cement mortar (1:3) with roughening of surface, including rubbing and polishing complete all as specified and as directed.

Material and labour for 15-18 mm thick machine cut kota stone slab shall be laid on wall / column / vertical surfaces, laid and jointed with grey cement slurry mixed with pigment to match the colour / shade of the slab over and including 10mm thick plastering / backing coat in cement mortar (1:3) with roughening of surface, including rubbing and polishing complete all as specified and as directed.

Material and labour 18-20 mm thick granite (of any type) tiles machine cut, bedded and jointed with grey cement slurry and pointed with white cement with pigment to match the shade of granite stone including grinding and polishing complete over 20mm thick screed bed in CM 1:3 complete all as specified and directed.

Material & Labour for Granite Stone Slabs of 20 mm thick as in Steps, Jambs, Pillars, Window Cills, Cooking Platform etc. and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and jointed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match the shade of the Granite Slabs including backing coat of mortar 20 mm thick in Cement Mortar 1:3 complete all as specified and as directed.

Material and labour 20 mm thick granite (of any type) tiles as in skirting / dado, machine cut, bedded and jointed with grey cement slurry and pointed with white cement with pigment to match the shade of granite stone including grinding and polishing complete including backing coat of mortar 10 mm thick in Cement Mortar 1:3 complete all as specified and directed.

Material and labour for 100mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregate) as in sub base floor and finish the surface even and rough complete all as specified and as directed.

Material and labour for machine pressed precast concrete interlocking paver block coloured red and yellow, any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade with grey cement and pigment including 50mm thick sand cushioning complete all as specified and as directed

Material and labour for cutting holes into or through brick walling built in cement mortar exceeding half brick but not exceeding one brick and making good in Cement Mortar 1:3 or Cement Concrete 1:2:4, Type B-1 as required for inserting hold fast etc and depth of embedded portion of hold fasts or lugs measured from the face of the jamb into the wall complete all as specified and as directed.

Material & Labour for 75mm thick, PCC 1:3:6, Type C-2, using 40mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing necessary joints 12mm wide to the full depth of PCC at every 3 meters and every change of directions and the joints duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

S & F stainless steel basket of size 420mmx485mmx100mm with external width 475mm as in cutlery, cup and saucer basket etc to kitchen drawer modular type made out of stainless steel 4mm dia wire at 30mm c/c and fixed to PVC kitchen cabinets with necessary fixing arrangement and sliding facilities complete all as specified and directed.

S & F stainless steel two shelf bottle rack of size 200mmx485mmx430mm with external width 200mm as in spice jar, bottles, glass jar etc. plain wire basket etc to kitchen drawer modular type made out of stainless steel 4mm dia wire at 30mm c/c and fixed to PVC kitchen cabinets with necessary fixing arrangement and rolling facilities complete all as specified and directed.

S & F stainless steel basket of size 380mmx506mmx150mm with external width 475mm, plain wire basket etc to kitchen drawer modular type made out of stainless steel 4mm dia wire at 30mm c/c and fixed to PVC kitchen cabinets with necessary fixing arrangement and rolling facilities complete all as specified and directed.

S & F in repairs Modular Cup Boards [Kitchen Cabinets] made of 18 mm thick (± 5%) superior quality 100% lead free, plain PVC sheets of minimum 0.55 density, including shutters and necessary fixing arrangement such as brackets, screws as required and all the edges shall be covered with 1mm thick edge bending tape or 90 degree edge bent finish all as per requirement, as specified and as directed. Note : Hardwares and decorative laminates shall be measured and paid separately under respective items of this Schedule/ BoQ.

S & F stainless steel basket of size 470mmx485mmx200mm with external width 475mm as in thali, plain wire basket etc to kitchen drawer modular type made out of stainless steel 4mm dia wire at 30mm c/c and fixed to PVC kitchen cabinets with necessary fixing arrangement and rolling facilities complete all as specified and directed..

S&F for Gola profile, Aluminium Handle of 200mm for doors of kitchen cabinets, complete all as specified and directed.

S&F for Gas pump Hydrolic gas spring (35kg load capacity) complete all as specified and directed

S&F for Lift up Hydrolic gas spring 100N (10kg load capacity) complete all as specified and directed

S&F for butterfly stainless steel hinges of 125mm size including screws complete all as specified and as directed.

S & F of stainless steel sliding/ telescopic channel of 500mm long with 03 Nos. of holding ball of load carrying capacity 45-50 Kg of 202 grade steel width 45mm including necessary fixing arrangement and rolling facilities complete all as specified and as directed

M & L for fixing 4mm thick anodised aluminium composite panel fixed in aluminium frame including necessary rubber beading, jointing cleat compete all as specified and as directed

S & F 25mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing including taking down of old unserviceable GI tubing complete all as specified and as directed.

S & F 32mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing including taking down of old unserviceable GI tubing complete all as specified and as directed.

S & F 50mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 [PN–16] UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing including taking down of old unserviceable GI tubing complete all as specified and as directed.

Supply and fixing 32 mm outer dia PP-R Gate Valve (brass insert) including taking down of old unserviceable stop valve complete all as specified and as directed.

Supply and fixing 25 mm outer dia PP-R Gate Valve (brass insert) including taking down of old unserviceable stop valve complete all as specified and as directed.

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil etc complete all as specified and as directed.

Returning, filling in including spreading and levelling watering and well remming in layeres n.exc. 25cm thick complete all as specified and directed.

Removing excavated material not exceeding 50 meters & depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed.

Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing complete all as specified and as directed.

All as per item No 155 above but for 3 pin 5 Amp socket outlet point controlled by one switch on the same board complete all as specified and as directed.

All as per item No 155 above but for 3 pin 5 Amp socket outlet point controlled by one switch on independent board complete all as specified and as directed.

All as per Serial Item No. 155 above but for One Light Point controlled by Two Nos. of, Two way Switches complete all as specified and as directed.

All as per item No 155 above but with FRLS stranded copper conductor 2.5 sqmm (nominal area), two single core, PVC insulated and unsheathed cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including FRLS PVC insulated stranded copper conductor 2.5 sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly.

All as per item No 155 above but with FRLS 4 sqmm starnded copper conductor for one power point on independent board and including 4 sqmm earth continuity wire for AC/equipments etc controlled by one SP/SPN MCB. .

Supply and fixing modular switch, 1 way, 6 A, 1 module complete all as specified and as directed.

Supply and fixing modular switch, 1 way, 16 A, 1 module complete all as specified and as directed.

Supply and fixing modular socket, 6 A, 2/3 pin, 2 module complete all as specified and as directed.

Supply and fixing modular socket, 6 / 16 A, 2/3 pin combined, 2 module complete all as specified and as directed.

Supply and fixing modular bell push switch 10 Amps, 230 volt one module complete all as specified and as directed.

Supply and fixing modular Bell Music type, 230 volt complete all as specified and as directed.

Supply and fixing modular switch 2 way 6 Amps, 230 volt one module complete all as specified and as directed.

Supply and fixing modular fan regulator 120 watt step type AC 220 Volt complete all as specified and as directed.

Supply and fixing Telephone Socket / Jack with Shutter, RJ-11, Modular Type, One Module including suitable Modular Type Pressed Metal Flush Box made out of 2mm thick MS Sheet, Modular type Base / Grid Frame & Cover Frame complete all as specified and as directed.

Supply and fixing TV Socket / Outlet, Co-Axial, Deluxe, Modular Type, One Module including suitable Modular Type Pressed Metal Flush Box made out of 2mm thick MS Sheet, Modular type Base / Grid Frame & Cover Frame complete all as specified and as directed.

Supply and fixing in repairs Surface & wall mounted Energy efficient 4 feet long LED Tube Light Fitting, of 20 W, 6500 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 0.75 Sq.mm 3 core and making good the disturbed surfaces to match with existing surfaces complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply and fixing in repairs Surface & wall mounted Energy efficient 2 feet long LED Tube Light Fitting, of 10 W, 6500 K of cool white, with extruded aluminium / CRCA housing and robust construction with necessary acrylic diffuser & integrated electronic driver, all accessories internally prewired and connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 0.75 Sq.mm 3 core and making good the disturbed surfaces to match with existing surfaces complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply and fixing in repair Decorative LED wall mounting, Champagne gold finish fixture with plastic body of 9 W, Base type B-22 LED lamp complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply & Fixing ceiling rose surface bakelite with three terminals complete all as specified and as directed

Supply & Fixing Energy efficient & Long life Building Security Light Luminaire, of 25 watt, 5700 K with Pressure Die Cast Aluminium Housing, IP66 protection, heat resistant glass cover, high power LEDs as light source, electronic driver including GI Bracket made out of 25 mm bore GI Tube, Medium Grade of size not exceeding 1.50 m in length and bent to shape required and fixed with 2 Nos of Pole fitting Clamps made out of MS Flat of size 50 X 6mm, bolts, nuts, washers and painting with two coats of aluminium paint over a coat of primer red oxide zinc chrome primer and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including taking down existing light fittings of any description and making good the disturbed surfaces to match with existing complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply and fixing in repair LED bed light with LED lamp, 3 W complete all as specified and as directed. Note: Light fitting shall be of PF>0.95

Supply & Fixing AC Starter motor single pole 25 Amps, 230 volt flush type complete all as specified and as directed.

Supply & Fixing wall mounted stainless steel baffle T-shaped kitchen chimney with air suction capacity of 1100 CMH complete all as specified with the following accessories:- (i) Width : 90cm (ii) Suction power : 1100m/hr (iii) Function type : Autoclean (iv) Filter Type : Filter less (v) Finish : Black matte + glass finish loaded with premium features. (vi) Control : Soft push Button (vii) Led : 2x2W LED (viii) Product Dimension (WXDXH) (mm) : 915x580x505mm (ix) Warranty : 5 years on motor and 1year comprehensive. Make: Cat Part No. Hood ALPH HC PB BK 90 of Faber or equivalent makes as specified in Particular Specification.

Supply & Fixing Exhaust Fan, 300mm Sweep, 1200 RPM, Metal Body, Heavy Duty, with Double Ball Bearing, Conforming to IS - 2312, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50 Hz, including Louvers Shutter / Grill and of approved colour including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and fixing in existing opening and making good the disturbed surface to match with existing and taking down existing ceiling fan of any description and depositing at MES Store Yard complete all as specified and as directed.

Supply & Fixing exhaust fan made of sturdy engineering plastic 250mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with 3 core flexible copper cable including making holes on the wall and making good to the disturbed surfaces including taking down and removing old UNSV fan and depositing to MES store yard complete all as specified and as directed.

M & L for Taking down Ceiling Fan of any description from its position and refixing the same after repairs to buildings, at same place or at new place including connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm including cleaning, greasing and spray painting with two coats of synthetic enamel paint of approved colour over a coat of zinc chrome primer after filling cavities with filler and replacement of Spares such as Bearings, Shaft Bushes, Capacitor, Cotter Pin, Clamps, Rubber Bushes, Nuts & Bolts etc. as required complete all as specified and directed.

Supply & Fixing Energy efficient, Low Noise, Ceiling Fan, 1200mm Sweep of any colour as approved, 03 blades, BEE 5 Star Rated, with BLDC Motor, Copper Wound, 350 RPM, with Double Ball Bearing, Conforming to IS - 374, ISI Marked, suitable for operation on Single Phase, 240 Volts, AC, 50Hz, including Down Rod, Canopies, Shackles, Safety Rope, Hanging Clamps, Bushes, having P.F >0.95, Service Value >6.5, Air Delivery >215 CMM, Power Consumption less than 35 Watt, THD less than 5% including provision of Electronic speed control Regulator step type, including connecting up with twin core PVC insulated, sheathed flexible copper conductor cable of size 1.5 Sq.mm and taking down existing ceiling fan of any description and depositing at MES Store Yard complete all as specified and as directed. Note: Ceiling Fan shall be provided with 03 Years onsite replacement warranty. Rate quoted is deemed to be including the same and nothing shall be paid extra on this account.

Supply and fixing of MCB DB SPN 12 ways, powder coated, double door, 230 Volts, including bus bar neutral link, earth bar and din rail, for fixing MCB of various rating including taking down old unserviceable DB alongwith MCBs including making good disturbed surfaces complete all as specified and as directed.

Supply and fixing of MCB DB SPN 8 ways, powder coated, double door, 230 Volts, including bus bar neutral link, earth bar and din rail, for fixing MCB of various rating including taking down old unserviceable DB alongwith MCBs including making good disturbed surfaces complete all as specified and as directed.

Supply and fixing of MCB DB SPN 4 ways, powder coated, double door, 230 Volts, including bus bar neutral link, earth bar and din rail, for fixing MCB of various rating including taking down old unserviceable DB alongwith MCBs including making good disturbed surfaces complete all as specified and as directed.

Supply & Fixing of MCB SPN of capacity 6-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and as directed.

Supply & Fixing of MCB SP of capacity 6-32 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed.

Supply & Fixing of MCB SPN of capacity 40-63 Amps, 240 V, 10 KA 'C' curve complete all as specified and directed.

S & F in repairs MCB DB, VTPN, 6 Way, 415 Volts, with DIN Channel, Double Door with 200 Amps rated bus bar with neutral link and earth bar suitable for mounting MCBs/MCCBs including making good disturbed surfaces complete all as specified and as directed.

Supply and fix in MCCB 4 Pole, 125 Amps, (Ics=100% Icu) Adjustable type with breaking capacity of 16 KA, 415 V complete all as specified and directed.

Supply and fix in MCCB 4 Pole, 100 Amps, (Ics=100% Icu) Adjustable type with breaking capacity of 16 KA, 415 V complete all as specified and directed. Note for serial Item No. 188 to 196: MCBs/MCCBs and SPN,TPN, VTPN DBs shall be of same make as approved by GE/ AGE (I).

Cutting Bituminous Road / Hardstanding etc. as required for Jointing / Laying Cables and Pipeline of width not exceeding 450mm and depth not exceeding 200mm and refilling after laying and making good with PCC 1:2:4, Type B1 using 20mm graded stone aggregate, 100mm thick complete all as specified and as directed.

Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm dia by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion including taking down old unserviciable earthing set complete all as specified and as directed. Notes:- (i) Main earthing strip from earth plate electrode to rest point upto length of 7.5 meters length shall deemed to be included in the unit rate quoted against this item. (ii) On testing after completion if the desired resistenance is not obtained the contractor shall redo the earthing without any extra cost to the department.

Taking out old U/s XLPE cable of any size/type complete all as specified and as directed.

Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 50 sqmm 3.5 core laid in trenches/fixed to wall/under road/pipe as per IS 7098 (Part I) etc including cable glands, aluminium lugs complete all as specified and as directed. Note:-Excavation and earth work will be measured and paid separately

Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 25 sqmm 4.0 core laid in trenches/fixed to wall/under road/pipe as per IS 7098 (Part I) etc including cable glands, aluminium lugs complete all as specified and as directed. Note:-Excavation and earth work will be measured and paid separately

Material and labour for well burnt subclass 'B' bricks of size 230mmx115mmx75mm laid flat width wise along the length of cable for cable protection complete all as specified and as directed.

Materials and labour for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cable including spreading and punning down to desired thickness complete all as specified and as directed. (Note: Punned thickness shall be measured for payment purpose)

Supply and laying 40 mm bore galvanised GI tubing, light grade with all fittings for passing of UG cables including taking down of unserviceable GI tubing complete all as specified and as directed.

Supply & Fixing 600 mm long x 15mm dia Stainless Steel braided Flexible Hot & Cold Water connections complete all as specified and as directed.

Supply & Fixing of Clamp suitable for fixing of 25/35/50 ltrs water heater tank of any make complete all as specified and as directed.

Supply & Fixing Energy efficient, BEE 5 Star rated Storage type Water Heater [Geyser] 25 Litres Capacity with 2000 Watt Capacity heating element Conforming to IS - 2082, Vertical Storage type with stainless steel Inner Tank with dry powder fero glass line coating technology and ABS Outer Shell complete fixed to wall with suitable expansion fasteners including 02 Nos. of 450 mm long x 15mm dia Stainless Steel braided Flexible Hot & Cold Water connections and 15mm bore Non-Return Valve including taking down of old unserviceable water heater and deposited to MES store yard complete all as specified and as directed.

Please Enable Macros to View BoQ information