Special repair to Bldg No NP 08 and NP 09 of 307 Fd Hospital Under GE East Ferozepur Cantt

Amount

B/R WORKS Dismantling floor, hearth or wall tiling including cement morter bedding (but not backing removing seviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material & labour for Non skid ceramic coloured tiles7 to 8 mm thick (square) area of each tiles exceeding 0.11 Sqm but nexc 0.18 sqm,in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed

All as per item No. 2 herein here-in-before but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified and directed

Material & labour for Non skid ceramic coloured tiles7 to 8 mm thick (square) area of each tiles exceeding 0.06 Sqm but nexc 0.11 sqm,in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and directed

M&L Coloured Glazed ceramic tiles in vertical surfaces 300x450mmx7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incuding 10mm thick rendering/ plaster in CM(1:4) on fair face of brick or concrete surface complete all as specified and directed.

M&L for Vitrified ceramic tiles 8-10mm thick (Square/rectangular)polished area of each tiles n exc 0.36Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured (Light Shade)cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar(1:6) for laying floor finishes. complete all as specified and directed..

All as per item No. 6 herein here-in-before but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified and directed

M&L for Green marble slab, 16-18mm thick of size not less than 1 square metre each, machine cut as cooking platform or in any position, set and bedded in gray cement slurry over & including 15mm thick screed in cement mortar (1:4) and pointed in white cement with admixture of pigment to match the shade of granite including cutting, polishing (mirror type) complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level), complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick, surfaces finished even and fair without using extra cement including provision of construction joints complete all as directed by Engr-in-Charge and as specified.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc, complete all as specified and directed.

M&L for 25 mm thik Sand filling under floors or in foundations including watering and consolidation, complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block, with grey cement and pigment, any shape and size confirming to IS 15658-2006 of 80 mm thickness M-35 Grade complete all as specified and directed.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified and directed.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius, complete all as specified and directed.

All as per item No. 15 hereinbefore but using old bricks retrieved from demolition under item 14 hereinbefore including cleaning and removal of mortar from old bricks complete all as specified and directed.

Taking down cement plaster or terrazzo from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering/plastering, 15mm thick in cement mortar (1:4) on brick work/concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L Rendering 5 mm thick in cement mortar (1:3) on RCC Shelves and projections in concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L Rendering 10 mm thick in cement mortar (1:4) on ceiling concrete surfaces finished even and smooth without using extra cement, complete all as specified and directed.

M&L for Preparation of new plastered surfaces and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of walls & applying applying two coats of oil boumd distemper over coat of primer complete all as specified and directed.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats coats of white wash complete all as specified and directed.

M&L Preparation of old decorated plastered or unplastered by brooming down with steel wire brush, scarping down smoke soot, mould, moss and efflorescent salts and trading oil, greasy spots and applying one coat of oil bound distemper complete all as specified and as directed.

M&L Preparation of old decorated plastered surfaces of walls after complete removal of existing treatment and applying two coat of cement base paint over a coat of primer complete all as specified and directed.

M&L Preparation of old decorated plastered or unplastered surfaes and applying one coat of white wash on ceiling including cornices, pillasters etc complete all as specified and as directed.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified and directed.

All as per item No. 28 herein before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each, complete all as specified and directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

All as per item No. 30 here-in-before but size 125x60mm with double rebate, complete all as specified and directed.

M&L for Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats including necessary form work complete all as specified and directed.

S&F 35 mm thick, 2nd class hard wood, plain framed, panelled shutters (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particles board medium density wood particle board with comercial face veneers, size of members as specified in SSR partI, section 8 clause 8.24 (a) complete all as specified and directed.

S&F 2nd class hardwood 35mm thick Glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut & mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); to chowkats, complete all as specified and directed.

S&F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010), complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified and directed.. Make: Rajshri or equivalent as approved.

Refixing wooden shutters of any description in same opening exc 1.00 Sqm but n.exc 2.00 Sqm each, complete all as specified and directed

S&F PTMT tower bolts, 200 mm long and fixed with steel screws complete all as specified and directed.

S&F PTMT butt hinge, 100mm long, fixed with steel screws with brass/bronze hinge pin complete all as specified and directed.

S&F PTMT handle 125mm long fixed with steel screws complete all as specified and directed.

S&F Mild steel framed work of as in grills/guard bars shouldered with steel window/ ventilator frames complete all as specified and directed.

S&F Framed mild steel work of grade E-165 (Fe-290) as in framed work such as doors, gates or frame for cooler stand with gusset plates, rails, braces etc, drilled for fixing of sheeting or other covering of door etc, to be prepared for hanging or sliding etc including either hooks and hinges or steel hanging door fittings and hanging and fixing complete all as specified and directed.

S&F Factory made box type steel window with pintle hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel ventilator with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and directed and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified and directed.

S&F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

S&F Aluminium alloy body and tongue and roller plate floor door stopper of 150mm size fixed with steel screws complete all as specified and directed.

S&F Mild steel butt hinge, 100mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified and directed.

S&F Aluminium tower bolt of extruded section, 200mm length of bolt and fixed with screws, complete all as specified and directed.

S&F 125mm size, aluminium (cast type) anodized, handle and fixed with screws complete all as specified and directed.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy and fixed with screws complete all as specified and directed.

S&F 300mm Mild steel ordinary rate tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Mild steel curtain rod powder coated with fixing side brackets, end cups, rings @ 10 Nos per running metre and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified and directed.

Dismantling of boarding as in shelves complete all as specified and directed.

M&L for 18-19mm thick pre-laminated particle board, flat pressed single layer type or three layer type with BWR type adhesive, medium density interior grade having one side decorative lamination and other side balancing white lamination as in cup board shutter/shelves including 6 mm thick teak wood leaping on three sides and 20mm thich on hanging side & French polishing to edging complete all as specified and directed.

S&F for Hasp and staple of aluminium anodized, safety type, 100mm long, fixed with screws complete all as specified and directed.

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified and directed.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

Fixing only, after cleaning old steel water tubing, 15mm bore and connections in new or old position using new fittings complete all as specified and directed.

Fixing only, after cleaning old steel water tubing, 20mm bore and connections in new or old position using new fittings complete all as specified and directed.

S& F Towel rail, 19mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs as in repair complete all as specified and directed.

S&F PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed in repairs complete all as specified and directed.

S&F 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified and directed.

S&F in repair 20mm bore brass ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule , complete all as specified and directed.

S&F in repair 15mm stop cock cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with long shank and cup (concealed type), complete all as specified and directed.

S&F in repair 15 mm bore bib tap of, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, complete all as specified and directed.

S&F Vitreous china white squatting pan orrissa pattern of size 580mm x 440 mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ or 'S' trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, fixed as in repair, complete all as specified and directed.

S&F in repair Viterous China wash down water closet pan (pedestal pattern), white incl. Seat and cover (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed

S&F 15mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) fixed in repairs complete all as specified and directed.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing as in repair complete all as specified.

S & F in repair to CP WHB mixer 15mm bore. complete all as specified and directed. by Engineer in Charge

S&F in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP bracket guard & railing 60cm long complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S&F 1mm thick stainless steel sink, plugs, washers, PVC waste pipe, union, CP coupling & fixed in RCC cooking platform, overall size of sink 915mmx460mm, bowl size 410mmx330mmx160mm as in repair complete all as specified and directed.

S&F 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass as in repair complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. (fitting measured separately).

S&F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in rain water pipes as in repair complete all as specified and directed.

S&F 110 mm bore PVC (SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified and directed.

S&F 110mm bore, PVC (SWR), P trap with cement joints, complete all as specified and directed.

S&F in repair 75mm borePVC (SWR) floor trap, plain with grating including jointing with solvent including jointing to waste pipe in run lead as in repairs complete all as specified and directed.

S & F in repair Jet Pressure with chromium Plated flexible connection pipe, spreader and hock complete. Complete all as specified and directed.

S&F Tolilet paper holder, vitreous China white, box type to walls with CP (CP) brass screws, complete all as specified and directed.

S&F in repair grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed

S&F 40 mm Low density polyethelne (LDPE) pipes of pressure rating 6kgf/sq. cm, complete all as specified and directed.

S&F, 0.560mm thick stainless steel plate rack of standard pattern & 31'x36' size including fixing to wall with 4 nos 50 mm & PVC rawl plugs complete all as specified and directed.

S&F in repair CP brass health faucet single nozzle type with flexible full CP Shower tube and abs stand, complete all as specified and directed.

Raking out joints / Pointing to Brick work or Brick tiles, laid flat in floors, surface channels, roofs etc. work built in cement or cement Lime mortar, complete all as specified and directed.

M&L Flush pointing to roof tiles in cement mortar (1:3) tiles including racking out joints complete all as specified and directed.

M&L PCC in roof kerbs of mud stops, rounded or chamfered on edges type B1 (1:2:4) using 20 mm graded stone aggregate complete all as specified and directed.

Dismantling unframed timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section, in any position, complete all as specified and directed.

S&F Steel work in tabular trusse incl. special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 11614-1979 grade St-240, complete all as specified and directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof covering, complete all as specified and directed.

S&F Pre painted galvatume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L, Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over primed steel surfaces complete all as specified and directed.

Dismentling fencing wiremesh any type, complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section including taking out embedded portion and making good disturbed portion embeded in concrete, brick work, masonry etc complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu m, getting out, returning, filling in and ramming in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surfaces in soft/loose soil complete all as specified and directed

M&L for PCC ( 1:4:8) type D-2 using 40 mm graded brick agg as in foundation all as specified and directed by EIC.

M&L for cement concrete type C-1 1:3:6 using 20mm graded stone aggergate in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rouinded for chamfered angles and throating, as direted as EIC.

S&F Mild steel work as in posts or struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) including all necessary bolting or riveting etc and similar work confirming to Fe-290 Gde E-165, complete all as specified and directed.

S&F Tie bars with screwed ends, nuts, washers and mild steel paltes for walls, chimneys, roofs, arches, etc. king rods and straining bolts conforming to Fe 410-0 or Fe 310-0, complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10 cm long diameter of the neck in 5 to 10 mm, complete all as specified and directed.

S&F Mild steel Round bars 10mm dia and over,cut to length, bent to shape required, complete all as specified and directed.

S&F GI chain link fancing 100 mm diagonal mesh size of 2-3 mm dia wire fixed angle iron fencing post including prov. of binding wire complete all as specified and directed.

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strainging bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or stel pins, etc. complete all as specified and directed. (each line wire to be measured)

Demolition of reinforced cement Concrete of any description & in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition). Complete all as specified and directed

M&L Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate set in CM(1:4) in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, including necessary form work complete all as specified and directed.

Use & waste form work (rough finished) to sides & soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports overhangs, etc also splays between floors and beams, etc complete all as specified and directed.

Use & waste Form work to soffits of suspended roof slabs not exceeding 200 mm thick (horizontal or slopping rough finished Flat surface of concrete complete all as specified and directed.

M&L cement concrete type B1 (1:2:4) using 20 mm graded stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic & other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed complete all as specified and directed.

M&L RCC type B0 (1:2:4) using 12.5 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed.

M&L Mild steel TMT bars 6mm to 8mm dia,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mmdia or securing with clips complete all as specified and directed.

E/M WORKS Taking down carefully existig copper/ alumn point wiring for light/ fan/ bell/ socket 5/15 Amp points complete with fitting and fixtures such as Switches, Sockets, Ceiling Rosess, Holders and Bracket fittings with battens/ conduits/ wires, T/L fittings and making good the disturbed surfaces of walls and roofs etc and to match with existing colour complete all as specified and directed.

Taking down carefully unserviceable main switches and distribution boards with fuses/ MCB's (single phase or three phase) of any capacity all as specified and directed.

Taking down carefully old unserviceable sub main wiring including meters and making good disturbed surfaces and matching with existing complete all as specified and directed.

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through & including PVC rigid concealed conduit, medium grade of suitable size (not less than 20mm dia) duly ISI marked with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/ sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed, stranded (Green colour) connected to common earth dolly complete all as specified and directed. for One light/ fan/ bell/ Bldg security light point controlled by one single pole one way switch.

All as per item No. 122 here-in-before but One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board, complete all as specified and directed.

All as per item No. 122 here-in-before but One 3 pin 5 Amp socket outlet point controlled by one switch on same board, complete all as specified and directed.

All as per item No. 122 here-in-before but one 15 Amps socket outlet point controlled by one single pole switch one way and wiring with 2.5 Sqmm PVC insulated, stranded, unsheated copper conductor on independednt board with continuous earth wire of size 2.5 Sqmm green colours PVC insulated, unsheathed, stranded copper conductor cable complete all as specified and directed.

S&F Switch modular type 6 amps, 1 module single pole one way duly ISI marked, complete all as specified and directed.

S&F Switch modular type 16 amps, 1 module single pole one way duly ISI marked, complete all as specified and directed.

S&F Socket outlet modular type 6A - 2 in 1,without shutter, 2 module, duly ISI marked, complete all as specified and directed.

S&F Socket outlet modular type 16A, 3 pin combined, 2 module, duly ISI marked, complete all as specified and directed.

S&F modular type bell push switch, 6 Amp, 1 module single pole one way duly ISI marked, complete all as specified and directed.

S&F Door Bell Ding Dong single phase 240 volts, white in colour, duly ISI marked complete all as specified and directed.

S&F Ceiling rose surface type, 240 volts, 50 Hz, 6A, Pilot 3 plate, white in colour, bakelite 65 x 50mm, 3 terminals duly ISI marked complete all as specified and directed.

S&F Lamp angle holder (Plastic Ring), 240 volts, 50 Hz, 6A, white in colour, duly ISI marked complete all as specified and directed.

S&F LED bulb of 10 watt complete all as specified and directed.. Make-Havells/ Crompton/ Wipro.

S&F rotary Stepped type electronic fan regulator for ceiling fan 1200/1400mm size, 240 volts, 6 Amps, 2 module, 100W, white in colour, duly ISI marked complete all as specified and directed.

S&F Ceiling fan 1200mm sweep, AC single phase 230 Volts 50Hz, including provision of flexible cable 3 core copper conductor of size 23/0.0076 of suitable length from ceiling rose to ceiling fan upto 1.5 mtr for giving connection and all hanging arrangement i.e. standard down rod, hanging clamp, with rubber real nuts bolts, spring washers and locking of splite pin, plastic canopy with screw compete without fan regulator and marking of MES nos with black synthetic enameled paint all as specified and directed.

S&F Recess and surface mounting LED flat panel 2'x2' made of CRCA sheet duly powder coated with high efficient LEDs & glare free full opal diffuser IP20 of 36 W, complete all as specified and directed.

S&F 20W, 6500 K, 4 feet LED Square tube light fitting, energy efficient fixed to wall/ ceiling etc complete all as specified and directed.

S&F LED sleeky bldg street light (Lens) fitting of 35 watts, 6000K, including GI bracket bend to shape made out of GI pipe light grade of 25 mm, size up to 1.2 mtr long etc complete with MS clamps made of 25x3mm MS plate, duly painted with two coats of aluminium paint with nuts/ bolts/ washers and all fixing arrangements to wall/ pole, including connecting up with 2 core copper flexible wire of size 23/00.0076 complete all as specified and directed.

S&F Sheet metal enclosures with socket plug top and MCBs Single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole MCB of 240V, 20 amps, 10 KA duly ISI marked complete all as specified and directed.

M&L for Post Top guarden/ gate light of 4 W, IP-65 protection, madeup of steel type including GI pipe suitable lights, excavation, returnling, filling and PCC works complete all as specified and directed.

S&F Factory made three phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail suitable for use on 240/415V, 50Hz supply, VTPN DB, partly immersed in wall, including of MCCB 4 pole adjustable thermal & fixed magnetic type 100 Amps, 50Hz, 415 Volts with rupturing capacity 16 KA and making good distrubbed surfaces with matching colour, complete all as specified and directed.

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 8 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, complete all as specified and directed.

S&F Factory made single phase and neutral Sheet Steel made out of CRCA 1.2 mm thick, powder coated double door vertical distribution board 4 way, dust and vermin proof, fitted with two cover, one screwed cover for incoming and outgoing MCBs and the second for protection of MCBs fitted with colour bus bar of capacity 200 Amps, neutral link, earth bar and din rail. suitable for use on 240V, 50Hz supply, partly immersed in wall and making good distrubbed surfaces with matching colour, ccomplete all as specified and directed.

S&F MCB SPN, 40A - 63Amps, 240 volts, "C" series, 10KA duly ISI marked, in MCB DB, complete with connection testing and commissioning complete all as specified and directed.

S&F MCB SP, 6A-32 Amps, 240 volts, "B" series, 10KA duly ISI marked, in the MCB DB, complete with connection testing and commissioning complete all as specified and directed.

M&L for Sub main wiring with two single core 2x4 sqmm PVC FRLS insulated and unsheathed stranded copper conductor alongwith earth wire 4.0 sqmm drawn in and including PVC rigid conduit connected to main board complete all as specified and directed (Two runs cable and one number earth wire and suitable PVC conduit shall measured together as unit length).

M&L for Sub main wiring with two single core 2x6 sqmm PVC FRLS insulated and unsheathed stranded copper conductor alongwith earth wire 6.0 sqmm drawn in and incuding PVC rigid conduit connected to main board complete all as specified and directed (Two runs cable and one number earth wire and suitable PVC conduit shall measured together as unit length).

S&F exhaust fan heavy duty with louvers complete of sweep size 300mm, 900 RPM, single phase, with bolts, nuts and washers, size of the bolt 15 cm long 12mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/00.0076 three core from ceiling rose to exhaust fan max 1.5 mtr for giving connection complete all as specified and directed.

M&L for Cutting holes making good the distributed surface to match with existing surface, grouting nuts for fixing of Exhaust fans complete all as specified and directed.

S&F AC Three phase electronic kWh energy meter of rating 5A-20A, class 1.0, 3 x 240V, 50Hz, counter type display with tranparent hinge type box poly carbonate body including connection and PVC flexible pipe, complete all as specified and directed.

S&F Sheet metal Meter Box single door minimum size 35x50x25cm for electric meter Factory made of MS sheets/CRCA sheet duly painted with powder paint and door hinged locking arrangement conforming to IS 5039 of 1983. The electric meter/switch box shall be suitable for fixing one number of electric meter and knock out holes for incoming and outgoing cable. Before the powder paint process the sheet steel shall go through the anti corrosion conditioning process in not less than seven tank process. Concealed in wall, including making good distrurbed surfaces with matching colour, complete all as specified and directed.

M & L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 4 mm dia galvanised iron or steel wire, complete all as specified and directed.

Earthing complete with galvanized steel plate elecrode of size 60 cm x 60cm x 6 mm thick burried directly in ground vertically to a depth not less than 2.5 mtr below the ground level with top edge of earth plate at a depth not less than 1.5 mtr below ground level. Earth plate surrounded by 15mm thick packed alternative layers of charcoal dust and comman salt, earth lead GI wire of 4mm dia (8 SWG) by means of bolts , nuts, check nuts and washers of galvanised iron with thimbles. The other end of GI earth wire is connected to main switch board and protected by light grade GI pipe of 15 mm bore. provision of 20mm bore light grade GI pipe for watering including GI funnel and wire mesh. Pipe shallbe provided vertically upto top level of earth pit and then taken horrizontally to the earth pit. Cement concrete chamber of PCC (1:3:6) type C-2 using 40 mm graded stone aggregate.The chamber shall be constructed one metre away from edge of earth pit. 50 mm thick pre cast cover of cement conrete (1:2:4) type B-1 using 20 mm graded stone aggregate and MS angle iron 50 x 50 x 6 mm frame including two coats of painting over a red oxide to exposed steel surfaces. excavation in soft / loose soil, returning filling and removal of surplus soil to a distance of 50 mm as directed and shown in Electrical Plate No- 3 of SSR Part-1 (2009), complete all as specified and directed.

S&F XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 25 Sqmm nominal cross section, 4 core, Circular aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified and directed.

S&F XLPE insulated, armoured, 1100 volts grade, heavy duty cable of size 6 Sqmm nominal cross section, 2 core, Circular, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified and directed.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan,for laying of cable and getting out, complete all as specified and directed.

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified and directed. (Excavation and earth work measured separately).Note- Punned down thickness shall be measured.

S&F Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified and directed.(Excavation and earth work measured separately).

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified and directed.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified and directed.

S&F Mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles/ walls, laid under floor/road crossings, complete with and including clamps socket & elbow etc complete all as specified and directed.

Marwaha Builders

M/s G N Const. Co.

M/S Pee Kay Builders

ABHISHEK AND COMPANY

M/s Vishant Construction Co