Construction Work

Amount

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Upto 2m depth

From 2-3m depth

Earth work open excavation in all soils and sub soils and to a full depth as may be directed except in rock requiring blasting inclusive shoring, strutting dewatering wherever found necessary, depositing the excavated earth at site of work in Places shown by the departmental officers with an initial lead of 10m and lift of 12m,clearing and leveling the site etc. complete complying with standard specification.

Supplying and filling in foundation, basement, etc with filling M-sand in layers of not more than 15cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Providing and laying,spreading and compacting graded stone aggregate to Wet Mix Macadam 250mm thick specification including premixing the material with water at OMC in mechnical mix plant carriage of mixed material by tipper to site laying in uniform layers with paver in Sub base/ Base course on well prepared surface and compacting with vibratory oller to acheive the desired density including cost of material, labour charges,rentals for machinery,fuel and all other incidentials charges etc., complete as per clause 406 of MORTH Rev-5.

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and filling in basement with Stone dust (Quarry dust) in layers of not more than 15 cm thick, well rammed watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For Circular Columns

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kglms and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement

In Ground floor

In First Floor

In Second Floor

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

Foundation & Basement

In Ground floor

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedastal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealents for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed.

Brick work using using Second Class Table Moulded Chamber Burnt Bricks of size 9" x 4-3/8" x 2-3/4 " in Cement Mortar 1:5 (One cement and Five crushed stone sand) including curing neat finishing, etc., complete complying with standard specification.

For foundation & basement

Brick work in Cement Mortar 1:6 (One cement and six sand) Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS: 12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc., complete complying with standard specifiction.

In Ground floor

In First floor

In Second floor

Brick partition walls of 11cm thickness using Fly Ash Bricks of 230 x 110 x 70mm size in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

In Ground Floor

In First Floor

Laying of screed concrete using Cement concrete mix 1:2:4 ( one cement, two sand and four hard broken stone jelly) using HBGS 6-10mm ISS metal for wearing coat including laying, compacting, finishing and curing etc., complete as per standard specification and as directed by the departmental officers

Paving the top of roof with solar reflective ceramic tiles (required design) of 305x 305x 7mm thick of approved quality and colour laid in cement mortar 1:3 (One cement and three sand) 20mm thick and pointed with tile grout (Nitotile Grout or equivalent) and cement in the ratio of 1:3 for joint ,curing etc., complete complying with the standard specification and as directed by the departmental officers. (The make and brand of the tiles (Johnson endura or equivalent) should be got approved by the Executive Engineer before use on works)

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 Part I to IV in stages to suit the progress of work consist as per the detailed specification as below. (Measurements taken for the plinth area for the purpose of payment) including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing, etc,complete and as directed by the departmental officers. (The chemical should be got approved by Executive Engineer before use on work).Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete, in bottom and sides of foundation.Stage-2:Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth. Stage-3: Spraying anti-termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60cms and at 60cms intervals on both direction and at junction of wall and flooring thoroughout.Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment

Water proofing treatment in RCC Roof slab: Surface Preparation : Preparing the surface (Main Slab) to ensure free from dust, Greece, oil, water, or any unwanted partials, minor repairs using mortar or PU sealant, Construction of Hunching at junction Providing and installing of cracks /construction/ cold joints in slab, slab & wall junctions & in other areas of the slab with Catalyst Crystalline repair mortar by using Catalyst Crystalline Penecrete Mortar & finishing coat of Penetron over all treated areas Waterproofing Coating; Supply and applying of Single Component, UV Resistant, High Quality Solvent free PU based Elastomeric Liquid Coating “FLEXIMAXX PU-1K” of BITUMAT complying with ASTM C836-95, having Crack bridging property of 3.4 mm, Tensile Strength 480 N/cm2 as per ASTM D412 with Elongation >440% , Adhesion to concrete of 72N/cm^2, Shore A Hardness >68 as per ASTM D2240, Applying Primer Coat + 2 Main Coats of FLEXIMAXX PU-1K with a minimum l coverage of Approx., 1.4kg to 1.5Kg per Sqm with the minimum reinforcement 4 inch width strip of 40 -60 GSM geofabric of non Wowen fabric of 100% Polyester staple fibers, mechanically bonded by a needle punching process and then thermally set to produce a dimensionally stable network with elongation break of 40%, Mullen burst strength of 60 KpA, Tensile strength (CD) of 2N/mm2 as reinforcement layer

between two main coats of Fleximaxx PU 1K and all overlapping and junctions.on typical locations like wall & floor junctions ect.. as per manufacturer's specifications approved by Department officials. the treatment includes necessary treatment along the vertical surfaces and inverted beams up to 300mm & sprinkling of quartz sand over vertical surface applied PU coating when it is still wet for receiving protection plaster on it. (The materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification).

Providing, mixing, laying polymer based water proofing treatment for the Sunken Toilet / Lift well / OHT Rcc wall by applying cement based, flexible, waterproofing compound confirming to IS:2645, to a thickness of 1mm of the prepared surface of the roof slab / floor slab as per specifications mentioned above providing cement mortar 1:3, waterproofing cover plaster to a thickness of 12mm over the membrane coating with admixture of approved make. Rate quoted is inclusive of preparation of surface, which includes cleaning of surface polymer mortar curing, labour, tools and equipment, etc. Rate inclusive of grouting with cement and sand required for the treatment, the cost and labour charges for fixing 25mm dia pressure pipes 15kg/cm2 to a length of 45cm for drip pipes, etc. complete.

Brick jelly Lime Concrete of 1:2:5 (One Lime,Two Sand and Five Brick ielly ) with 40mm hand broken brick ielly for Sunken portions including dewatering wherever necessary and laid in layers of not more than 15cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.

Paving the floor with best approved quality fine polished jet black Granite Slab 1200mm x 600mm, 16mm to 18mm Thick laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best approved quality Flamed Steel Grey Granite Slab 1200mm x 600mm, 16mm to 18mm Thick laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best quality Double Charged Vitrified Tiles 800 x 800 x 10mm of approved colour, shade andquality laid in cement mortar 1:3 (one cement and three sand)20mm thick in all floors and the top pointed with the white cementmixed same colour pigments etc., complete complyinE withstandard specification. (The make and brand ofthe tiles should beJohnson / Kajaria / Somany / Nitco / RAK which has to be gotapproved by Executive Engineer before use on works)

Flooring with Self design JJoint free Rectified Glazed Ceramic Flooring Tiles 305 x 305 x 8mm laid over 20mm thick cement mortar 1:3 (Onecement and Tree sand) base mortar over the existing slab / floorincluding cutting the tiles to the required size with special cutterwherever necessary, laying in positionand and pointing with whitecement mixed with colouring pigment at the rate of 0.3 kg. / sq.m.etc., complete complying with standard specification. (The makeand brand of the tiles should be Johnson / Kajaria / Somany / Nitco/ RAK or Equivalent which has to be got approved by executiveEngineer before use on works)

Dadooing walls with Joint free rectified Colour designed digital print ceramic tiles, with borders, with size of 300mm x 600mm x 10mm and above setin Cement Mortar 1:2 (One Cement and Two sand) 10mm thick andpointing the joints with white cement mixed with colouring pigmentsat the rate of 0.40 Kg. / sq.m. nbatly in all floors, curing, etc,,complying with standard specification and as directed by thedepartmental officers. (The make and brand of the tiles should belike Johnson / Kajaria / Somany / Nitco

Dadooing walls with colour design glazed tiles of size 300mm x 200mm x 6mm best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Providing grooving to granite slab at the intermediate edges of the vertical face with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Providing single nosing to granite slab at the edges of the vertical space with neat finishing etc complete with standard specification and as directed by the departmental officers.The cost including higher charges of machines and labour charges etc complete

Providing double nosing to granite slab at the edges of the vertical space with neat finishing etc complete with standard specification and as directed by the departmental officers.The cost including higher charges of machines and labour charges etc complete

Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.

Providing and filling the tile joint with epoxy grout with following specification: Surface preparation including cleaning the joint to be free from dust and loose particles. Providing masking tape on either side of the tile joint edges and providing sealing the tile gap with epoxy tile joint grout and finishing neatly and as directed by the departmental officers. The rate inclusive of cost of materials and labour, etc., complete.

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly,etc.,complete complying with standard specifications and as directed by the Departmental Officers.The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick mixed with Bonding agent Cebex112, Zydex -Zycrete 2X or other Equalent compound conforming to BIS at 200ml of One cement bag (50kg) for increased workability and air entrainment used finishing including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Providing the texture finish to the newly plastered wall with ready made texture putty with patterns at all levels including the cost of coating, labour charges and other incidental charges etc., complete as directed by the departmental officers

Supplying and applying Putty with two coats of plastered wall surface of first class quality and of approved including thorough scrapping, clean removal of dirt wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc.,complete complying with standard specification.

Supplying and fixing Teak Wood frames for doors Windows and Ventilators using required MS angles, flats and rods of approved design and as directed by the departmental officers including cost of MS Grills, labour charges and cost of one coat of red oxide primer with labour charges for priming coat etc. complete complying with standard specifiction.

T.W Scantling below 2m

T.W Scantling below 3m & above 2m

Supplying, hold fast of M.S flats of over all size of 330x50x6mm suitably folded to the required L shape have two end of lap of 50mm long each and overall length of the horizontal portion as 230mm & including making necessary grooves in two end laps to accomadate screws etc., complete.

Supplying and fixing in position of Teak wood door shutter using spl quality teak wood planks of 40 mm thick panelled doors with required raw materials, Brass hinges, Brass tower bolt, ornamental Brass handles, Door stopper, Door closer,Brass aldrops and bush with suitable locking arrangements etc. The rate should be inclusive of cost of materials, labour charges for wrought and put up the doors with kadasal charges and transporting charges etc complete complying with standard specification and as directed by the Departmental officers.

Providing Stainless Steel Salem Stainless Steel Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying and fixing in position of Solid Core Flush Shutters with Laminted sheet of 1mm thick on both side with teakwook lipping alround 35mm thick with of applied shade and hot pressed bonded with liquid phenol formaldluide resin with internal lifting with TW as per IS 2201/ part I /1991 The rates inludes the labour charges for fixing the shutter to the frames and for fixing furniture fiitings.The rate include the cost of furniture fittings etc complete

Single leaf

Polishing the teak wood shutters / teak wood frame / teak wood vener for doors with two coats of Melamine polish to wood surface as per direction etc., the rate inclusive of cost of materials ,labour charges ,transportion charges, labour for scrapping charges, etc complete complying with standard specification and as directed by the departmental officer

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle.The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and fixing of Fly Proof Mesh for Doors and Windows using 50mmx25mm x3mm M.S Square tube outer frame over window ,shutters with M.S "Z" and "T" section of size 25mmx25mmx3mm tk. Stainless steel fly proof mesh sandwich with inbetween the M.S Square tube as per standared specification and as directed by the departmental officers.

Supplying and Fixing Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded section body tubular type universal hydraulic door closer with double speed adjustment like HARDWYN 'GAZEL' (or) Equivalent (with ISI Monogram)

Supplying and fixing of M.S. grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer, dismantling of walls / concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Providing and fixing 8 mm thick fully designed perforated calcium silicate board 2'x2' panel tiled false ceiling (Hilux) including supplying and fixing true horizontal level false ceiling with 24mm prelude grid system Using hot dipped galvanised steel section exposed surface chemically cleaned caping prefinished in backed polyester paint wall angle of size 3000x19 x19mm used in the periphery of the ceiling fixed to the wall, parttion with the help of screws at 600mm c/c. Mainrunner of size 3000x24mm suspended at a 1200mm c/c by using securely fixed to the structural soffit of RCC slab by using 6mm Nylon Rwl plug at every 1200mm(max)and 1200mm long cross tee of size 1200x24mm to interlocked between mainrunner at 600mm c/c(max) to form a grid of size 1200x600mm.600mm long cross tee of size 600x24mm is inserted to form a grid of 600x600mm and finally laying classic lite regular edge tiles of size 600x600x15mm

Supply and fixing of curtains with MS rod of 25mm dia powder coated finish fire proof curtains with/without lining cloth etc.,complete and as directed by the departmental officers.

Providing factory made pre-laminated FPVC (Formed Polyvinyl Chloride) Door Frame of the size 105x40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 6Nos. of 5mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners of 3Nos. to be provided for each vertical member, GI stiffeners of ('U'channel of size 29x9,1mm, 150mmlong) -3Nos. at hinge point, frame reinforcement of ('U'GI channel of size 46x22x0.6mm), bottom tie rod of('U'GI channel size of 15x15x1mm),etc., complete complying with the standard specification. The door frame should be got approved from the Executive Engineer before use on work

Providing of 35mm thick factory made pre-laminated ABS (Acrolynitrile Butadiene Styrene) Door Shutter moulded in different designs, consisting of all round frame made out of water proof solid foam PVC bar of size 20 x 32mm, reinforced by 32 x 32mm -2 Nos., for vertical made out of LVL (Laminated Veneer Lumber), core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of steel coated butterfly hinges -3 Nos., for each shutter and ISI make SS round lock complete for finished item of work, complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work

Providing stainless Steel handrails with 10mm thick toughened glass with necessary fixtures. The rate include all labours, transport, scaffloding and other incidental charges in cluding all fittings etc. The materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete

Supplying and fixing fine polished Jet Black Granite slab of 38/40mm thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg/sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

110 mm dia pvc pipe

Providing ornamental Sthapathi band of width 150/200 mm (two steps) (Shape and size should be directed by the Engineer-in charge of works ) using Cement Mortar 1:2 (One cement and two cement).The shape and size adopted as per the approved drawing and as directed by the departmental officers etc.,complete.

Supplying and Laying Rubber Moulded paverblock of 60-63mm thick with new one using cement concrete 1:2:4 for manufacturing, finishing,Curing and conveyence to site and laying etc., complete complying with standard specification and as directed by the deparmental officers.

Making through holes in Plain or Reinforced Cement Concrete with Diamond Core Drilling System by using BOSCH power tools of following diamete -Depth per cm

Packing the Toilet floor pipe corecutting for providing pipeline using Crystaline bonding agent which shall be applied as a bonding coat and non-shrink grout, after necessary surface grinding.

Drilling of bore wells 150 mm dia any where in Chennai city including transportation from the place with in the above district in alluvial soil sedimentary strata of clay and sand stone shale pebbles boulders etc by first taking pilot of 140mm/ 150mm/200mm dia and the enlarging to required dia by direct or revise rotary mud circulation method using contractor's rig fuel labour drilling betonies mud and water required for the drilling at the site shown by the departmental officers including construction of mud pit (Water available with in a lead of 1.5 Km) Drilling of 140/150/ 200mm pilot bore.

Reaming from 140 / 200mm dia pilot bore to 300mm dia bore as directed by the departmental officers upto 6M depth ending below Ground level

Supplying of 160 mm Dia Slotted PVC pipes of 6kg/cm2 (With slot or without slot) in the drilled hole including welding the joints etc., complete supplying and packing the annular space with pebbles size and quality as approved by the EE

Supplying of 160 mm Dia Plain PVC pipes of 6kg/cm2 (With slot or without slot) in the drilled hole including welding the joints etc., complete supplying and packing the annular space with pebbles size and quality as approved by the EE

Labour charges for inserting 165 /168 mm dia PVC casing pipes assemble (with slots or without slots) in the drilled hole including jointing the pipes with PVC coupler and with cement paste etc. complete and supplying and packing the annular space with pebbles of size and qualityas approved by the departmental officers. The conveyance charges to work site to be borne by the contractor.

Charges for developing the bore well for entire depth with suitable air compressor of 300RPM capacity (minimum 8 hrs) including transportation labour and fuel charges for compressor and directed by the departmental officers and conducting yield test by "V" notch methods, excluding the cost of bore charges and conveyance charges of handle boring.

Supplying laying and jointing HDPE pipes of 10kg/cm2 for borewell motor purpose of approved quality etc., complete and as directed by the departmental officers.

40mm Dia

Supplying and fixing of 2 HP of approved brand Submersible Pump with accessories of starter, Main switch, panel board etc. complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying and fixing of 2.00 HP of approved brand monoblock with accessories of starter, Main switch, panel board etc. complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying and fixing of 3 Phase Panel Board including labour charges, complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

Supplying and fixing of suitable PVC end cap (6Kg/cm2) for 6" dia bore well of best quality with ISI mark. (The PVC end cap should be got approved by the departmental officers before execution)

Supplying and fixing and connecting of 4 core 16 sq.mm Flat Sub mersible cable wire for the sub-mersible motor from panel board to sub-mersible pump.

Supplying and fixing of 20mm dia Nylon rope for submersible motor of approved quality in etc,complete complying with standard specifications.

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25 mm dia G.M. Gate Valve

32mm dia G.M. Gate Valve

40 mm dia G.M. Gate Valve

50 mm dia G.M. Gate Valve

Supplying and fixing in position 15mm dia following taps (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works)

Long body tap

Swan Neck Tap

Angle cock

Pillar tap

Supplying and fixing in position Stainless steel Two way Bib Cock with Health Faucet of Jaquar or equivalent make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (The material should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Stainless steel shower rose with Shower Arm and Two in One Wall mixture of approved make jaquar or equivalent with stop cock arrangement of size 15mm dia inlet with necessary cutting, threading and jointing using shellac etc., complete complying with standard specification and as directed by the departmental officers (The material should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position of Stainless steel Bottle trap of Jaquar or equivalent make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (The materials should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Frameless mirror of 5mm thick with size of 18 x 24 inch frameless modern mirror with beveled edges of Saint Gobin brand of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass Stainless steel towel rail 600mm long of approved make (Jaquar or Equivalent )with brackets of same materials including cost of teak wood plugs and CP screws, etc., complete complying with standard specifications. (The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality Stainless steel soap tray of approved make jaquar or equivalent including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing in position best quality approved make of Jaquar or equivalent under counter oval type wash hand basin of size 560 x 450mm with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Providing and fixing approved make jaquar or equivalent of white vitreous wall mounting type EWC with CP bolts, nuts, CI chair(painted with two coats of enamel paint over a coat of primer) or other hanging arrangemets, bakelite/polypropiline seat cover with CP hinges, rubber buffer, CP brass screw, washer with all accessories including cutting and making good the walls etc.,complete complying with standard specification and as directed by the departmental officers. (The materials should be got approved by the Executive Engineer before use on works).

Providing and fixing approved make jaquar or equivalent of concealed type cistern with dual flow facility comprising of actuator SS button facia assembly including brass / SS screws and washer complete providing protection cover over cistern cutting and making good the walls wherever required etc.,complete complying with standard specification and as directed by the departmental officers. (The materials should be got approved by the Executive Engineer before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the size 100 x 75mm with stainless steel gratings with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications.(The PVC pipes should be got approved by the Executive Engineer before use on works).

75mm dia

110mm dia

160mm dia

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

PVC Elbow

160mm dia

110mm dia

75mm dia

PVC Elbow with Door

110mm dia

75mm dia

PVC Tee

110mm dia

75mm dia

PVC Tee with Single Door

110mm dia

75mm dia

160mm dia

110mm dia

75mm dia

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications.(The PVC cowl should be got approved by the Executive Engineer before use on works)

110 mm dia

75 mm dia

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works.

20 mm dia

25 mm dia

32 mm dia

40 mm dia

50 mm dia

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements

UPVC Elbow

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Tee

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Reducer

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Reducer Elbow

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Reducer Tee

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Hex Nipple

50 mm dia

40 mm dia

32mm dia

25 mm dia

UPVC Union

50 mm dia

40 mm dia

32mm dia

25 mm dia

UPVC Coupler

50 mm dia

40 mm dia

32mm dia

25 mm dia

Supplying, laying and jointing CPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using CPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works.

15 mm dia

20 mm dia

CPVC Specials

CPVC Elbow

20 mm dia

15 mm dia

CVC Tee

20 mm dia

15 mm dia

CPVC Reducer

20x15mm dia

Construction of Inspection chamber or manhole of the following size including necessary earth work excavation in all soils to full depth as may be directed with sand filling at bottom of the chamber for 10cm thick, concreting CC 1:5:10 using 40 mm guage HBGs jelly 10 cm thick and sode walls 9" thick brick work in cement mortar 1:5 using Fly Ash Bricks of 230 x 110 x 70mm filling the size of foundation with excavated earth, plastering with cm 1:3 20m thick for inside and bottom and making necessary benching with brick jelly cement concrete to the required slope and finishing neatly etc., complete.

Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with following frame sizes including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.

600x600mm cover slab

750x750mm cover slab

Supplying and fixing of PVC mould CI Steps of approved quality including dismantling masonry wherever necessary and redoing the da maged portion to original condition

Providing rain water harvesting pit of 900 mm dia and depth 2m below the ground level.The sides of rain water harvesting pit is provided with RCC well ring of inner size 900mm ,depth 250mm and 50mm thick . The top of rainwater harvesting pit is finished with brick work of inner size 1m X 1m ,0.60m height and 23cm thick with best quality II class ground moulded chamber burnt bricks of size 9" x 4-3/8" x 2-3/4" in Cm 1:5 (One of cement, Five of sand). The brickwork is provided above a base course of 10cm PCC 1:5:10 and over a sand cushion of 10cm.The top is covered with RCC cover slab of 50mm thick with perforated holes.The inner,outer and top surface of brick masontry are plastered with cement mortar 1:5(one cement and five sand)12mm thick.The rain water harvesting pit is filled with coarse river sand of 30cm depth at bottom,20mm HBGS jelly of 40cm depth at middle and 40mm HBGS jelly of 1.05m depth at top.The rate is inclusive of cost of all materials,transportation charges and labour charges etc complete and as directed by departmental officers.

Supplying and fixing of King size Cot with Bed Side Box, Bed, Pillow, Pillow cover, Bed Spread. The external frames of cot 6½ X 6 are made up of teakwood, the internal frames are made up of Kongu or equivalent wood and the top plywood is 12mm in thickness. They are completely melamine polished. Bed 6½ X 6 Branded 6" thickness Mattress with Pillow, Pillow Cover, Bedspread etc., complete complying with standard specification.

Supplying and fixing of Writing table with Chair Table of size 900x600 made of 18mm thick commercial ISI grade plywood and all the exposed surfaces are finished 1mm thick laminated sheet and including supply of one chair and etc., complete as per the direction of departmental officers.

Supplying and fixing of Dinning Table of Size 7 X 3 feet oval table with 6 chairs Teakwood with Melamine Polish. The rate includes labour for manufacturing, supply, transportation, etc.,as directed by departmental officers.

Supplying and fixing of Three seater Sofa with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Two Seater Sofa with basic Silver Wood framework. The seat have flat type High Density cushions placed on the seat, back rest with fireproof cloth or leatherride. Bottom Legs with Floor Adjustable bush model sofa. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Teapoy of Size 900x600mm Teakwood with Melamine polish. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Library Book Rack - 3.30m x 3.30m height (width - 0.45m) completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. The rate includes labour for manufacturing supply, transportation, etc.,complete complying with standard specification.

Supplying and fixing of Wooden TableL1800 x D900 x H750mm Side Storage unit Size : L900 x D450 x H750mm Back Storage Unit Size 1800 X 450 X 750 Mobile Pedestal ( 3 Drawer ). Table Tops and legs made out of made out of 25mm or 18mm thick Commercial Plywood, all exposed edges are Machine pressed Edgebanding finish 3 Draw mobile pedestals of Size 400mm W x 450mm D x 680mm H completely made of 18mm Commercial Plywood finished with 2mm thick PVC machine pressed edge banding. Mobile unit to have central locking system with wheels The rate includes labour for manufacturing supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Executive Chair Optima High Back Revolving Chair 5 prong sheet metal base chromium fully polished powder coat finish micro tilting arrangements high suspension hydraulic arrangements. The rate includes all and as directed by the departmental officers.

Supplying and fixing of Visitors Chair with back in frame covered with breathable Mesh in black for back, with arm steel frame and leg chair 14 gauge CR round pipe legs, 18mm compressor plywood for seat with 3” thick high density foam covered with fireproof cloth, fixed arms, legs have nylon bushes. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Computer Table with Chair Table of size 4 X 2.5 Top & Leg made out of 25mm thick Prelam Particle Board and modesty made out of 18mm thick Prelam Particle Board all exposed edges are Machine pressed Edgebanding finish. with One Drawer and One Cupboard, Footrest, CPU Trolley, Key Board Tray. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Office Table with chair Table of size 4 X 2.5 Top & Leg made out of 25mm thick Prelam Particle Board and modesty made out of 18mm thick Prelam Particle Board all exposed edges are Machine pressed Edgebanding finish. with One Drawer and One Cupboard, Footrest, CPU Trolley, Key Board Tray. The rate includes labour for manufacturing, supply, transportation, etc., complete complying with standard specification.

Supplying and fixing of Study Table of size 3 X 2 made out of 18mm commercial plywood and 1 mm laminated sheet finish with all round teak wood beading fixing and plywood area good polish finish etc., The rate includes all and as directed by the departmental officers.

Supplying and fixing of Chairs (Wooden ) - Teakwood with Melamine Polish study chair with cushion seat. The rate includes labour for manufacturing, supply, transportation, etc., The rate includes all and as directed by the departmental officers.

Supplying and fixing of Kitchen Loft Cupboard made out of 18mm thick waterproof plywood (BWP) with both sides merino or greenlam or century laminate of 1mm thick of approved colour and design. The unit is made as a box section covered with 18mm thick BWR plywood. All the exposed edges are machine-pressed with edge banding finish of suitable material. Handles and Basic Hardware are of EBCO Make. The rate is inclusive of material, labour, necessary hardware, etc complete. The make and design shall be got approved by the Executive Engineer.

Supplying and fixing of Kitchen Base Unit made out of 18mm thick waterproof plywood (BWP) with both side merino or greenlam or Century laminate of 1mm thick of approved colour and design. The unit is made as a box section covered with 18mm thick BWR plywood. All exposed edges are machine-pressed edge banding finish. Handles and Basic Hardware are of EBCO Make. The Base unit shall accommodate the various units such as plain basket, cutlery tray, thali plate basket, carousel and oil pull-out basket with accessories. The rate is inclusive of material, labour, necessary hardware, etc complete. The make and design shall be got approved by the Executive Engineer.

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with 1.5 Sqm suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate with 1.5 Sqm suitable colour for Concealed PVC Pipe higher End

Wiring with 2 x1.5 sq.mm.PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with Continous earth wire connection of 1.5 sq.mm copper wire and making good of the concelaed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Supply and fixing of AC / DC 76mm buzzer / call bell suitable for 230 volts 50 c/s single phase AC supply on suitable TW board with push switch

Supply and fixing of 24w LED 1x1 square type fitting complete with PVC unsheathed copper leads from termials to the fitting.(Havells/Equ)

Supply and fixing of 2 x 2 34W LED square type fitting complete with PVC unsheathed Cu leads from terminals to the fitting (Havells / Equ)

Supply and fixing of 3W foot light complete with PVC unsheathed copper leads from terminals to the fitting (Luker/Equ)

Supply and fixing of 4' 40W LED flu fitting complete with PVC unsheathed Cu leads from terminals to the fitting (Havells / Equ)

Supply and fixing of 4' 22W LED flu fitting complete with PVC unsheathed Cu leads from terminals to the fitting (Havells / Equ)

Supply and fixing of 3W LED Round type Recessed fitting with necessary connection (Luker/Equ).

Supply and fixing of 2' 10W LED flu fitting complete with PVC unsheathed Cu leads from terminals to the fitting (Havells / Equ)

Supply and fixing of Bollard on ground with foundation, base plate arrangements and necessary connection. (Havells/Equ)

Supply and fixing of 18W round LED surface mounted Downlight fitting complete with PVC unsheathed copper leads from terminals to the fitting (Havells/Equ)

Supply and fixing of 25W LED Gate light fitting complete with on gate pillar with base plate with 300mm GI pipe with necessary connection.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED steet light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour .

Supply and fixing of 1200mm (48") sweep AC ceiling fan 5 star rated complete ( Higher end) with 2 module 100W fan step regulator (Higher end) with 300mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 450 mm (18") AC sweep wall mounting fan with clamps with neceassry connection (Havells/Equ)

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supply and fixing of 25L Electric Storage Water Heater (Venus / Equi) suitable for 230V 50 c/s AC supply on MS clamps with 3 core flex wire but without plumbing works.

Supply and fixing of 1 no.6A two module 5 pin socket , 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 2nos.6A two module 5 pin socket , 2 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 3nos.6A two module 5 pin socket , 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 4nos.6A two module 5 pin socket , 4 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 20A Flush type Wall Socket 32A DP MCB complete set for AC Plug in flush with wall with earth connection (For AC Plug)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and fixing of 7 segment 4 way TPN MCB sheet steel distribution board (Higher end) with metal / acrylic door cover flush type /surface type fitted with busbars and neutral links with single / three phase MCB outgoings and seperate 4 way provision for accomodating one no. 4 pole incoming MCB / Isolator and another seperate 4 way provision for accomodating one no. 4 pole ELCB / RCD (totally 8 ways in one segment) (3x 4 ways in each segment) and seperate provision for MCB / Isolators ( totally 12 nos.) for sub incomers in 3 segments with lable holder and provison for taking up cable for size not less than 35 sq.mm. with the following in flush with wall with earth connection only.

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB switch as incoming and 12 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed FRLS opper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 1.5 Sqmm Cu.wire and making good of the concealed portion with suitable colour

Supply and run of 2 of 2.5 sq.mm. (36 / 0.3) PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 2.5 Sqmm cu.wire and making good of the concealed portion with suitable colour

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 sqmm cu. wire with painting of suitable colour

Supply and run of 4 of 16 sq.mm. (101 / 0.45) PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 16sqmm copper wire and making good of the concealed portion with suitable colour

Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 6 sq.mm copper wire with painting of suitable colour

Supply and run of 4 of 10 sq.mm. (84 / 0.3) PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable colour

Supply and Erection of 415V/50Hz Cubical Metering Panel board with bottom bus bar chamber and switch chamber on top side of the bus bar chamber and metering chamber with viewing glass in the middle with 16SWG Thick CRCA Sheet with 1"x1/4" tinned copper flats for 3 phases and neutral with 6mm Hylem sheet separation of 3 phases and neutral and with synthetic moulded insulators bus support at equal intervals as per IS Specification and 1" x1/8" Copper flat on rear side of the panel board for earth buses with the following switches complete. 1. 125A TP SDF Switch -3 Nos (SDF Switches L&T Make /equivalent), 9 Nos 100A Porcelein fuse units and 3Nos 300A fuse units, Danger Board with powder coated painting ,necessary identification of out going loads ,bus capacity cable size with bold letter with display (Make L&T /Equivalent)

Supply and laying of 3 1/2 x 25 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 3 1/2 x 25sqmm PVC armoured LTUG cable on post or on wall with MS clamps.

Supply and laying of 3 1/2 x 120 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 3 1/2 x 120sqmm PVC armoured LTUG cable on post or on wall with MS clamps.

Supply and fixing of brass cable gland for 3-1/2 x 120 sq.mm. PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 120 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Earthing as per PWD standard with an earth electrode of 2 metre Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work

Supply and run of 1 of No.8 SWG GI wire for earth connection

Supply and fixing of SMC Sintex box with 6-32A DP MCB on wall with necessary connection.

Supply and fixing of SMC Sintex box with 6-32A FP MCB on wall with necessary connection.

Supply of 2HP single phase submersible Pumpset with DOL starter complete set including transport charges.

Supply of 1HP single phase Pressure booster monoblock Pumpset (Kirloskar/Equ) complete set including transport charges.

Supply and fixing of 5KVA single phase microporcessor controlled double conversion true online UPS system with builtin Isolation Transformer and power factor correction and manual By Pass arrangements with Exide sealed maintenance free batteries (12V - 65AH - 10 Nos) for 120 minutes backup time with suitable interlink cables with necessary connections with suitable rack arrangement for batteries etc.

Supply and Installation of 2TR Capacity 5 star rated energy efficient Hi-wall Mounting Split Type Inverter Air Conditioning Unit Consisting of Outdoor Condensing Unit complete with hermetically Sealed Air Compressor with R32 refrigerant, air cooled condenser, fan etc and 1 No Indoor Hi-wall Mounted 2 TR Capacity Evaporator unit complete with cooling coil ,blower motor and connected accessories ,control etc., with 3 meter copper refrigerant piping and cord wire connecting Indoor and Outdoor unit with drain pipe suitable for operation on 230V + 10V 50 HZ Single Phase AC Supply(Make Carrier/Toshiba/Voltas/Equivalent)

Supply and Fixing of 5KVA Capacity Automatic Voltage Stabilizer Double Booster with time delay relay wall mounting type with input voltage 170V to 240 V and Output Voltage 230V +10V and cut out limit suitable for 2TR Split Type AC Unit (Make VGuard/Equivalent)

Supply and fixing of M.S Stand for fixing of Outdoor AC Unit

Supply and Laying of 5/8” and 3/8” copper pipe with necessary installation complete

Supply and Laying of 1” PVC Heavy Duty Drain Hose with Suitable M.S.Clamps on wall complete

Towards charges for 3" dia core cutting for laying of copper wire and PVC etc.,

Supply and fixing of Reverse osmosis purifier with purifying capacity of 25 Ltrs and storage capacity of 15 Ltrs output 1 tap with 2 RO memberane Auto flushing, filteration 5 stage suitable operation on 230V single phase, 50Hz, AC supply

Supply and installation of RJ 45 i/o socket with module box and phase plate. Combo D-RJ45 CAT6E Lan I/O Network Keystone Jack, Gang Box, Single Port Face PlateType: 1x Keystone Jack + 1x Gang Box + 1x Single Socket Face Plate. Suitable for : CAT6 / CAT6E. Make:D-link/Eq.

Supply and Installation of RJ 11 I/O switch with moudle box and phase plate. Combo D-RJ45 CAT6E Lan I/O Network Keystone Jack, Gang Box, Single Port Face PlateType: 1x Keystone Jack + 1x Gang Box + 1x Single Socket Face Plate.Suitable for : CAT6 / CAT6E. Make:D-link/Eq.

Supply and installation of 24 port 10/100/1000 Mbps fully managed layer -2 switch with 1G uplink,24 x 10/100/ 1000 BASE-T ports Fanless design for silent operation Innovative D-Link Green energy saving features Complete web interface for comprehensive switch management. Make : D- link/Eq.

Supply and installation of 24 port patch panel -fully loaded.D-Link Category 6 patch panels are six port RJ45 modules applied and suitable for 22-26 AWG stranded and solid wire, compatible with both 110 & Krone punch down tools. D-Link patch panels have improved Cable Management with optional Cable Management bar terminating 4 pairs UTP cable. Make: D-link/Eq.

Supply and Installation of 4MP IP outdoor bullet Camera ,WDR 3.6 mm .with fixing clamp. 1/3 in. 4 MP Progressive-scan CMOS Sensor, Starlight Technology for Low-light Applications, Built-in Microphone, Triple-stream Encoding, Analytics+ Function – Perimeter Protection and Smart Motion Detection. Make: NEOS/Eq.

Supply and Installation of 8-port POE switch, which supports IEEE802.3 af/at poE standard, 8 x 10/100/1000BASE-T PoE ports, Compact design for convenient placement, Fanless design for silent operation, Innovative D-Link Green energy saving features , Complete web interface for comprehensive switch management. Make: D-link/Eq.

Supply and Installation of 20 channel Network Video recorder , H.264/ MJPEG dual code decoding upto 200 Mbps incoming bandwidth , 1 SATA HDDs up to 6 TB, USB multinet network monitoring web viewer. Make : NEOS /Eq.

Supply and Installation of 8TB built in Hard Disc Drive. Cost-effective storage upgrade for laptop or desktop computers – store all of your games, music, movies and more SATA 6Gb/s interface optimizes burst performance. Seagate Secure models for hardware-based data security Best-fit applications: Desktop or all-in-one PCs, home servers, entry-level direct-attached storage devices (DAS) Instant Secure Erase allows safe and easy drive retirement, plus protect data with Self-Encrypting Drive (SED) models. Make: Seagate/Eq.

Supply and Installation of 6U wall rack, with front glass door with lock and key facilities. Make : D-Link/Eq.

Supply and Installation of 32 inch LED TV for CCTV camera monitor. Make :Branded/Eq.

Supply and installation of 1 mtr. patch cord.Panel : Spcc. 1.5mm thickness with black (ral9005) color painted Rj-45 jack : Housing abs, ul94-0 Rj-45 jack contact : Material phosphor bronze with nickel palpated,Connector Type: Rj45. Make:D-Link/Eq.

Supply and installation of 0.5mm 2 pair telephone cable with suitable PVc pipe. Make : Finolex/Eq.

Supply and laying of CAT 6 cable in throw PVC pipe. Category : 6 UTP Solid cableConductor : Conductor : 23 AWG (Solid)Conductor Meta : Conductor Meta : Bare Copper Insulation Material HD-PEOD : 6 .1mm ±0.2Resistance Unbalance : 5% MaxCapacitance Unbalance : 330pF/100m Delay Skew : <45nS Using for LAN. Make:D-Link/Eq.

Supply and laying of 25mm dia PVC rigid pipe with PVC accessories on wall / ceiling/floor.

Supply and Laying of RG6 Cable connectors and accessories. Make:Orbit/Eq

Supply and Installation of Digital ISDN EPABX System most advanced communicaion system with 4 P&T line and 16 extensions line Ip upto 64 with Enabled called ID Conference Day/Night Mode voice mail extenstion lock with console. ISDN & Networking and 1 KVA UPS with 30 minutes backup.Make:NEC/Eq.

Supply and Installation of Caller ID Telephone instrument. Make : Beetel/Eq.

Supply and Installation of 10 pair DB with krone module and necessary connections.

Supply and Installation of 10 pair 0.5mm unarmoured telephone cable in existing PVC pipe. Make : Delton/Eq.

Supply and Installation of wireless Dual band Giga bit ceilling mount access point, speeds upto 450Mbps on the 2.4 GHz band and 1300 Mbps on the 5GHz band. Make : D-Link/Eq.

Supply and Installation of WiFi 6 Router EXO AX AX5400 Wi-Fi 6 technology provides faster speeds, greater capacity and less network congestion Next-gen speeds up to AX5400 (4,800 Mbps on the 5 GHz band and 600 Mbps on the 2.4 GHz band) Dual-band Wi-Fi with up 2.0 and USB 3.0 ports to create shared storage Intelligent Quality of Service (QoS) prioritizes network traffic to minimize the impact of busy bandwidth Backwards compatibility ensures support for previous Wi-Fi standards and all Wi-Fi devices Increased battery life of connected devices with Target Wake Time technology Supports WPA3™ — the latest WiFi . Make : D-Link/Eq. Model No : DIR-X5460 Wi-Fi 6

Supply and Installation of Tata sky DTH with one year subcription charges,8 way splitter,4 way splitter, super LNB 2.0 and other necessary connectors.

Testing and Commissioning charges for the LAN,EPABX,CCTV, WIFI and Cable TV wiring system arrangements.

GST at 18%

MUTHUSWAMY CONSTRUCTION (BID ID -1137249)

SRK ASSOCIATESS (BID ID -1139093)