SPECIAL REPAIR 5XTOILET BLOCK WITH HARD STANDING NEAR BLDG NO 9A RA LINE AT 153 INF BN( TA) DOGRA ,ADDN ALTN OF BLDG NO AC 14 A OF 9 ARTY BDE CAMP AND PROVN OF 2X SPLIT AC AT BLDG NO RHA -21 SYSTEM AND NFS ROOM AT 9 ARTY SIGNAL UNDER AGE B/R-I AND

Amount

Taking down old existing water proofing treatment from the top of RCC/ arch slab, including taking down existing PCC padding or plaster and hacking the top of RCC slab, cleaning with water and disposal of rubbish off the premises complete all as specified & directed.

M&L for 50mm thick (average thickness) PCC 1:2:4 type B-O (using 12.5 mm graded crushed stone aggregates) all as specified and directed.

M&L for 10 mm thick cement paster in cement mortar 1:4 mixed with WPC @ 2 % by weight of cement finised even and smooth without using extra cement on roof surface when concrete is green and wall complete all as specified & directed. ( Note :- WPC will be measured and paid seperately as supply only rate).

M&L for surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC shall be done with wire brushing to attain smooth leveled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the liquid applied membrane. Grout: Providing Chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementations grout Injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with instant setting cement. Angle fillets/Coving: Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add “multipurpose mortar”, 10% by weight of cement). First apply the bonding coat of Multi-Purpose Polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges. complete all as specified & directed. Note: Grouting will be done when and where ever required.

Treatment of pipe entry points: Preparing the inside surface of core and PVC /MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periphery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concrete Note: Will be done when and where ever required Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and as directed.

S&F in repair, MS framed work for ornamental and intricate design such as grills, guard bars of window and similar work with ends of bars shouldered and/ or riveted, or forged into spikes conforming to Fe 290(Gde E-165) complete all as specified and directed.

M & L for preparation of New Steel Painted surfaces of steel and iron work of any description over 10cm width or girth and applying two coat of synthetic enamel paint and over one coat of red oxide complete all as specified and as directed.

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided complete all as specified and as directed.

M & L for RCC M-25 Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like etc complete all as specified and as directed.

M&L for TMT bars 10 mm dia & over cut to length, bent to shape required including cranking bending spirally for hooping for column, hooking ends & binding with & including mild steel wire (not less than 0.9 mm dia) or securing with clips quality conforming complete all as specified and as directed.

M&L for TMT bars 6mm to 8mm dia cut to length, bent to shape required including cranking bending spirally for hooping for column, hooking ends & binding with & including mild steel wire (not less than 0.9 mm dia) or securing with clips quality conforming complete all as specified and as directed.

M&L for form work to sides of pillars posts, struts piers, columns & stanchions square rectangular or polygonal in shape fair finished flat surfaces of concrete complete all as specified and as directed.

M&L for 18 -20mm thick Black Granite factory made bull nosed, polished (table rubbed and polished) as in jambs, window cills, cooking platform and the like etc in cement mortar 1:4 including pointing in white cement (1:2) using marble dust and admixture of pigment to match with shade of stone including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:4 including rounding of edges, making hole for gas pipe complete all as specified and directed.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) exc 1.50 m and n.exc 4.00 Sqm each complete all as specified and as directed.

Taking down chowkhat or frames of door/ window with shutters (Without taking off shutter from the frame) not exc 1.50 Sqm each complete all as specified and as directed.

S & F 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed.

S&F factory made gauzed shutter made out of angle iron 35mmx35mmx5mm and 25mmx25mmx5mm and 1.5 mm thick, 10mm square bars grill with stainless steel wire cloth 0.5 mm nominal dia wire and 1.20 mm average width of aperature complete all as specified and as directed.

S&F steel windows with side hung shutters incl projecting type hinges with steel handle and steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F steel windows with side hung shutters incl projecting type hinges with steel handle and steel peg stay complete without glazing bars dovetailed or welded complete all as specified and as directed.

Taking down of cement plaster of any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M & L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces finished even and fair complete all as specified & directed.

M & L for applying 15 mm thick rendering using ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @ 3% by weight of cement or as per manufacturer instructions, complete all as specified and directed Note : Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge within 15 days of acceptance of contract.

M&L for preparation of newly plastered surfaces of wall by applying wall care putty averaging thickness 2mm and rubbing with sand paper for making smooth surface and applying two coat of oil emulsion distemper over one coat of primer through roller, complete all as specified and directed .

Supply only integral WPC complete all as specified and as directed.

M&L for preparation of new surface of of wall by applying 3mm thick wall care putty and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified and directed.

Demolition of brick work or stone/boulder masonary built in cement mortar incl all quoins arches pillars etc.all as specified & directed

M & L for plain Cement concrete 1:4:8 ( Type D2 using 40 mm graded crushed stoneaggregate) in in foundations,filling and mass concrete complete all as specified and as directed.

M & L for brick work with sub class fly ash bricks straight or curved on plan exc 6 m mean radis built in cement mortar 1:6 complete all as specified and as directed.

-Ditto- all as per item No 29.00 above but except bricks complete all as specified and as directed.

M & L for Providing precast cement concrete typeB1 1:2:4 (20mm graded graded graded aggregate) in window or door cills, lintels,bressumers, steps,quoin blocks (for use with ma sonry), string courses, copings.kneelers, apex stones, pier caps,columns, posts,boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling).corbels, brackets, etc. (of any section indicated), with plain fair faces, including cham fers, weatherings, throat- ing etc. and setting in mortar complete with joints to match complete all as specified and directed

Dismantling timber scantlings 40 sq.cm and over in section, in any position unframed work complete all as specified and directed

S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including notching, drilling, fittings, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing fittings angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing conf to Fe-410-w (Gde-E -250) quality A complete all as specified and directed.

Demolition for Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for Hardcore of broken stone guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

M & L for 75mm thick Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) as sub base complete all as specified and as directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade, with grey cement and pigment over and including 50mm thick river sand cusion and packing the edges/sides of the blocks with PCC 1:2:4 complete all as specified and directed

Excavating in post holes(or similar holes) each n.exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, in soft/loose soil complete all as specified and directed

M&L for PCC 1:3:6 type C2 using 40mm graded stone agreegate as in bed blocks to fencing post complete all as specified and directed

M&L for New or previously un treated steel Surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint applying two coats of Synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

Dismantling asbestos cement (corrugated, semi-corrugated, etc) sheet in roof coverings complete all as specified and directed

S&F pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

S&F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/ridges etc, fixed with self tapping screws complete all as specified and directed

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) removing serviceable tiles to store andd rubbish off the premises complete all as specified and directed

S&F non skid coloured ceramic tiles 7-8mm ( Square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm in floor laid set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including screed bed 15 mm thick in cement mortar (1:6) , complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350X250X7mm/450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10mm thick in cement mortar (1:4) , complete all as specified and directed.

Taking up or down steel tubing and connections for 15mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections for 20mm bore of pipe complete all as specified and directed.

S&F tubes medium grade, galvanised with all fittings and fixed complete to walls and ceiling or laid in floors for 15 mm bore complete all as specified and directed

All as per item No. 49.00 above but 20 mm bore pipe complete all as specified and directed

S&F 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and directed.

S&F 15mm dia chromium plated fancy type wall mixer with over head shower for mixing hot & cold water screwed, fixing and connection to pipes complete all as specified and as directed. Make:- Cera Cat Part No F-1017401, Pearl Cat Part No ARI-015, Hindware Cat Part No- F-74 0022 or equivalent make in PS

S&F in repair gun-metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specified and directed

M & L for cutting chases for concealed water tubing, pinning in, making good of facings where required and pointing in cement mortar 1:3 to ends or edges etc, cutting not exceeding 10 cm width or girth, complete all as specified and directed

S&F triple layer white color 500 Ltrs Rotational moulded polyethylene (PVC) water storage tanks cylindrical vertical with closed top including nipple nuts and washers for fixing inlet, outlet/washout pipes and air vent pipes and incl dismantling water tanks any type & removing complete all as specified and directed

S&F in repair, Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 ltr capacity hoisted and fixed in position all as specified in SSR Part I, including taking down of exiting tank, complete all as specified and directed by Engineer in Charge.

S&F 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair bib taps brass cromium plated 15 mm bore size screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15 mm dia stop cock/angle cock cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle, flench screwed both ends for iron or for union complete all as specified and directed

S&F in repair PVC low level flushing cistern 10 litre capacity valveless syphonic action type white i as approved incl ball valve float valve and handle,32 mm dia flush pipe complete all as specified and directed

S&F vitreous China wash basin including pedestal, white, flat back, size 550 x 400 mm, including fixing acessories like galvanised brackets & rag bolts,32 mm CP waste coupling complete all as specified and directed .

S&F PVC connections of 450mm long suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

S&F in repair brass chromium plated shower rose 125mm size all as specified and directed

S&F in repair CP brass soap dish complete all as specified and directed

S&F in repair PVC Pipes single socketed in any length with rubber ring joints, fixed to walls, laid under floors etc. 75mm bore as in waste and rain water pipes complete all as specified & directed.

S&F in repair PVC Pipes single socketed in any length with rubber ring joints, fixed to walls, laid under floors etc. 110 mm bore as in waste and rain water pipes complete all as specified & directed.

S&F PVC bends 75mm bore, any radius complete all as specified & directed.

S&F PVC bends 110 mm bore, any radius complete all as specified & directed.

S&F 15 mm dia brass chromium plated central hole wash basin mixture, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut capstanhead screwed for 15mm dia pipe fixed in repair complete all as specified and directed

S&F in repair chromium plated towel rail 20mm dia D type 600 mm long as a approved quality.complete all as specified and directed.

S&F, in repair, PVC waste pipe 32mm bore of size 450mm to 600mm long complete all as specified and directed.

S&F glass corner shelf fancy type made of 6 to 7 mm thick sheet glass of size 250mmx250mm fixed with chromium plated brackets complete all as specified and directed.

S&F in repair of vitreous china squatting pan ‘Orrisa pattern’ size 580 x 440 mm white with integral foot rest including replacement of ‘P’ or ‘S’ trap lime concrete bedding and making good floor complete all as specified and directed.

S&F in repair ,PVC(SWR) floor trap, 75mm bore, plain with grating including jointing with solvent cement complete all as specified and directed

S&F in repair ,PVC(SWR) gully trap, 125/110mm bore, plain with grating including jointing with solvent cement complete all as specified and directed

Dismantling of cast iron ,PVC or reinforced concrete drain pipes, 75/110/150/200 mm dia, jointed in cement mortar and taking out of trenches, if required, Complete all as specified and directed by Engr-in-charge.

M&L for ultra P E,DWC (Double wall corrugated) pipe confirming IS-16098 Part-2 2013 pertaining structure wall plastics pinning system for sewage 150MM and above bore pipe SN8 and all necessary fittings and fixtures complete all as specified and directed.

M&L for ultra P E,DWC (Double wall corrugated) pipe confirming IS-16098 Part-2 2013 pertaining structure wall plastics pinning system for sewage 1200MM and above bore pipe SN8 and all necessary fittings and fixtures complete all as specified and directed.

Demolition of cement concrete as in bed to drain pipe including packing under and haunching against the sides of pipe or as in manhole benching/bed etc complete all as specified and directed by Engineer-in-Charge.

M&L for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150mm bore pipes complete all as specified and directed by Engineer-in-Charge.

M&L for Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 200 mm bore pipes complete all as specified and directed by Engineer-in-Charge.

M&L for Precast cement concrete type B-1, 1:2:4 using 20mm graded crushed stone aggregate as in manhole cover complete all as specified and as directed by Engineer-in-Charge.

M&L for Dewatering of Septic tank soakage well and manhole of any depth in any position by pumping out and removing outside Military/Defence land by mechanical means (trolley mounted) and burying in pits all as directed including digging of pits in any type of soil and covering pits with earth after absorption of water and including providing and spreading required quantity of bleaching powder around the pit or dispose of waste material as per state protocol and washing the top of septic tank & soakage wells and surrounds with fresh water and sprinkling lime to make hygeinic complete all as specified and directed by Engr - in Charge.

M&L for De-sludging of septic tank of any capacity including connected intercepting chamber, manhole shaft, sludge chamber & filterbeds of any description and in anmy position by pumping out and removing of sludge outside Military/ Defence land by mechanical means (trolly mounted) and burying in pits all as directed including digging of pits in any type of soil and covering pits with earth after filling of sludge and including providing and spearding required qty of bleaching powder or dispose of waste material complete as per state protocol, including taking down of slab cover and placing the same in existing postion complete all as specified and directed by Engineer-in-Charge.

S&F, in repair, vitreous china wash down water closet pan (Pedestal pattern), white with 'p' or 's' trap (excluding flushing cistern and flush pipe), including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. complete all as specified and directed.

M & L for in repair Plastic water closet seat, black / White, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed

M & L for construction of Soakage wells , of size 2.40m dia & 6.00m depth ( effective depth 4.5 m ) in ordinary Soil, Foundation in PCC 1:3:6, wells of Honey combed and solid in M-25 Concrete, including intercepting chamber, screen chamber Brick work in cement mortar 1:4, RCC cover slab in M-25/ RR masonry / Filling with brick bats, all as including necessary earth work in any type of soil (soft / loose / hard / dense) all as shown on drg No TD-309 Sh. 1/4 to 4/4. complete all as specified and directed.

M&L for construction of septic tanks, foundation in PCC 1:2:4, brick work in cement mortar 1:4, RCC Slab covers including RCC precast manhole cover having 6mm plate embedded all around/fibre reinforced cover with angle iron frame Vent shaft and sludge chambers etc., for 25 users including necessary earth work in any type of soil (soft / loose / hard / dense) all as shown on drg No TD-217 sheet 1/7 to 7/7 complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in soil complete all as specified and directed.

Removal of excavated soil to a distance n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed .

Dismantling wall and ceiling boards(fibre, pulp, insulation, etc) or insulation boards/slabs/blankets any thickness, including cover fillets complete all as specified and directed

S&F tee grid suspension system of size 600 mm x600 mm type-1 made out of rolled framed hot dipped galvanised steel zinc coated of not less than 120 gm/sqm ,main runner shall be 0.3 mm thick of section 24 mmX33 mm cross runner 0.3 mm thickof section 24 mmx25 mm,wall angle shall be 0.63 mm thick of section 24 mmx24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod ,system exposed portion shall be pre painted polyster coated in off white/white in colour complete with material,fixing, jointing etc all as per manufactures instructions and directed.

S&F fibre cement coloured textured designer ceiling board 4mm thick of size 595x595 mm conforming to IS : 14862 & IS : 2380 Part-XIV fixed to timber / GI / Aluminium frame work with screws/clips complete all as per manufactures instructions complete all as specified and directed

M&L for Hollow PVC Wall lining consisting of 5 mm thick plain colour pvc sheet inclusive of solvent cement and fixing at site on PVC Frame with 5mm pvc fillets as per specified and drawing shown as per page of SSR part II . complete all as specified and directed.

S&F powder coated anodised aluminium windows sliding type (3 shutter type) with sash bars, aluminium sections weighing 0.55 Kg/mtr (minimum) incl stainless steel mosquito proofing wire mesh fixed with , clips, frame , necessary joining cleats, glazing clips, neoprene rubber gasket with aluminium beading screws suitable anodised fittings such as hinges, handles including powder coated anodised aluminium frame, grill with one or more rebates including S&F 5.50 mm thick black glass complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

Taking down carefully any type of battens or conduit point wiring with conduit (light, fan, socket or power) complete including fittings and fixtures such as switches, sockets, ceiling roses, lamp holders, pendent light fittings, MCBs / isolators, fan regulators, tube light fittings etc removing material from site and making good disturbed surfaces of walls, ceilings etc including two coats of white / colour washing / distempering etc to match the existing complete all as specified & directed.

M&L for point wiring with 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, stranded, FRLS PVC insulated, unsheathed, copper conductor cable in and including PVC concealed conduit of any size/dia complete with all accessories/fittings, brass screws, washer etc, sunk zinc coated pressed steel terminal boxes with 3mm thick plastic laminated sheet top cover concealed in wall with and including continuous earth wire of size 1.5 Sqmm nominal cross sectional area, single core, PVC insulated stranded copper conductor cable, unsheathed and connected to common earth and earth duly complete all as specified and directed for One tube light/ Bulb/ street light point controlled by one, one way switch 05 / 06 Amps.

All as per Srl item No 103.00 here-in-before but One fan/exhaust fan point controlled by one, one way switch 05 / 06 Amps complete all as specified & directed.

All as per Srl item No 103.00 here-in-before but One 3 pin, 05 / 06 Amps socket outlet point on independent board controlled by one, one way 05 / 06 Amps switch complete all as specified & directed.

All as per Srl item No 103.00 here-in-before but One 3 pin, 05 / 06 Amps socket outlet point on same board controlled by one, one way 05 / 06 Amps switch complete all as specified & directed.

All as per serial item No 103.00 here-in- before but with 2.5 Sqmm nominal cross sectional area copper conductor cable for one 15 / 16 Amps socket outlet point on independent board complete all as specified & directed.

S & F switch piano flush type 05/06 Amps single pole, one way 240 volts complete all as specified & directed.

S&F socket oulet, 05 / 06 Amps 240 volts complete all as specified & directed.

S&F socket outlet 3 pin, 05 / 06 Amps and 3 pin 15 / 16 Amps (2 in 1 Multipurpose) 240 volts complete all as specified & directed.

S&F switch piano flush type, 15 / 16 Amps single pole, one way 240 volts complete all as specified & directed.

S&F ceiling rose, 3 phase/PVC/polycarbonate isolated body complete all as specified & directed by Engineer -in- Charge.

S&F lamp holder (Angular / Straight), insulated body, with back plate all as specified and directed.

S&F LED lamp 2 pin 9/10 watt complete all as specified and directed.

S&F LED light fitting 1x22/25 watt,220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S&F LED light fitting mirror type with high output diffuser 2 feet,10 watt 220V, AC decorative type with driver holder and LED lamp including connecting up with three core flexible copeer conductor cable of suitable size complete all as specified and directed.

S&F 1x36/40W LED Building security light energy saving & environmental friendly long life luminaire with high power LEDs as light source and electronic driver including security light brackets of 32 mm dia GI pipe medium grade upto 1.2 mtr long bend to shape at 100-120 degree including flat iron clamps and Suitable nuts and bolts grouted in wall including all material required for fitting all as specified and directed.

M&L for sub main wiring with 06 Sqmm nominal cross sectional area, two single core, 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor cable with and including continuous earth wire of size 06 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC concealed conduit of 25 mm dia, medium grade with all conduit accessories / fittings, brass screws, washers etc and connected to common earth dolly including taking down old u/s wiring & incl all cutting / chases etc in wall, making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed.

S&F sheet metal enclosure double door, single pole and neutral, AC, 240 volts, 8 way, with 200 Amps rated copper bus bar and IP - 43 protection with metal double door and flush to wall including all cutting on wall and making good including two coats of white/colour washing/distempering etc to match the existing disturbed surfaces complete all as directed by Engineer - in -charge.

S&F MCB, SP, AC, 240 volts 'C' curve capacity of 06 to 32 Amps, 10kA and making connections complete all as specified & directed.

S&F Double pole Isolator 240V, 40A, and making connections complete all as specified & directed.

S&F Exhaust fan PVC with louver and fixing accessories 230 Volt and 250 mm sweep complete all as specified and directed.

S&F Water heater storage type steel body with copper inner tank and heating element upto 2KW capacity 25 ltr, BEE 5 stared complete with a rating including providing of hold fast in wall and PVC connection 45 cm long with 15 mm dia brass union at both end heavy duty complete all as specified and derected by Engr-in-charge.

M&L for making opening in the wall for fixing exhaust fan up to 250mm / 300mm,including plastering work & making good the surfaces to match the existing complete all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60cement mortarx60cement mortarx6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level steel earth plate connected with GI wire 04mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15mm bore light grade all as shown in elect plate No.3 of SSR part I connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150mm thick around GI earth plate, GI pipe medium grade 20mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover in PCC 1:2:4 type B1 duly reinforced with MS Bars 6mm dia at the rate of 150mm center to center both way with suitable lifting handle and pit / chamber in PCC 1:3:6 type C1 , Angle iron 40x40x5mm frame for pit cover including testing on completion complete all as specified and directed.

S&F XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade cross sectional area of 10 sqmm 2.0 core complete all as specified and as directed.

M&L for clean fine dry river sand in trenches for cushioning of under ground cable/ cable duct complete all as specified and as directed. Note: Only punned thickness shall be measured for payment purpose.

M & L for fly ash brick protection length of brick shall be laid across the length of cable) all as specified and directed.

M&L for GI light grade tubing 40mm dia laid in trenches, road crossing , pasing through pipe or laid in wall/pole complete all as specified and directed.

Supply and instalation of split type air condisner electric divice single phase 230 volt 50 Hz rotary compresser, air condition 585/1600 efm, noise level 38 db. Digital type LCD freme steel two way auto air swing, with 5 star rating of capacity of 1.5 TR complete all as specified and directed..

supply ,laying commissioning ,testing of XLPE under ground LT cable 1100 volts grade of size 16 sqmm 2 core armoured PVC sheathed with aluminium conductor heavy duty laid in trench ,fixing on wall ,under road crossing through proctection pipe etc complete all as specified and directed including taking down old LT UG cable complete all as specified and directed.

S & F sheet metal single pole and meteral enclosure with 2 pin plug and socket 240 volts with one single pole MCB 20 Amps complete all as specified and directed

S&Fautomatic electronic voltage stabilizer of capacity 5.0 KVA having feautre such as intelligent time delay system, low and high voltage cut-off protection, latest IC technology to protect from power fluctuations, Thermal over load protection, wide input variation between 170V to 250V with output voltage stabilized at 220 to 240V with accuracy of +/- 2.5%. complete all as specified and directed.

SA construction co.

vibha associates

mohanlal gupta