REPAIR OF WALL PLASTER FLOORING TILING JOINERY AND OTHER ALLIED WORKS IN SUNDER JI ENCLAVE CARRIAPPA ENCLAVE BC JOSHI VED VIHAR VAIDYA ENCLAVE SN PARK BI LINE JNC ENCLAVE MANEKSHA ENCLAVE RA LINE ROORKEE LINE ETC MD OFFICERS ACCN AREA

Amount

M&L for 25mm thick PCC (1:2:4) type BO, (using 12.5mm graded stone aggregate) sub base as in floor to receive tiles complete all as specified.

M & L for reinforced cement concrete (design mix) M-25 (using 20mm graded stone aggegrate) as in chajja and the like and including all neccesary formwork & finishing exposed concrete surface all as specified and directed

M &L for Brickwork with fly ash bricks old size bricks straight or curved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the liquid applied membrane. a) Grout: Providing Chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementitious grout Injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with instant setting cement.Angle fillets/Coving: Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add “multipurpose mortar”, 10% by weightofcement). First apply the bonding coat of Multi-Purpose Polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges. Note: Grouting will be done when and where ever required. b) Treatment of pipe entry points: Preparing the inside surface of core and PVC /MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periphery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concrete . Note: Will be done when and where ever required

c ) Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface. 33 % water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3(Resin:Hardner) Supplying, providing and applying waterproofing treatment to Podium area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation. Material coverage 1.2kg /sq.mt. (Note: Contractor is required to deposit the material covered in this item up to 00% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.

M&L for cutting chases, pinning in, in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring. etc. and making good, cutting not exceeding 10cm girth complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) not exc. 1.5 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) exc 1.5 sqm but not exc. 4 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame at site as per specification & drawing on srl page No 174 of SSR Part-II complete all as specified and directed.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x 150 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note : - (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. (ii) For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note : - (i) M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately. (ii) For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F powder coated (thickness of powder coating not less less than 50 micron) anodised aluminium frame for doors , windows, ventilators with one or more rebates with and including joining cleat for fixing etc complete all as specified and directed

S&F powder coated (thickness of powder coating not less less than 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55 kg/m with and including necessary joining aluminium cleats, aluminium glazing clips, ruber neoprene packing suitable size of aluminium, handles 2 Nos in each door, stainless steel hinges anodised aluminium snap beading secrews etc complete all as specified and directed.

S&F in repairs stainless steel fancy type curtain rod 25mm dia, complete all as specified and directed.

Supplied and fixed CP over head shower 100mm dia round shape single flow (ABS Body chrome plated with Gray face plate) with rubit cleanig system Inc connection with wall mixer. Make : CERA(Cat No : F 101540) complete all as specified and directed

S&F in repairs 100mm size, 4 levers, aluminium mortice lock vertical type complete all as specified and directed.

S&F Glazing with sheet 4mm thick ordinary quality and glazing with oil putty and glazing pins in squares exceeding Sqm in each pane complete all as specified and directed.

S&F brass barrel tower bolts,with cast or sheet berrel and rolled or cast bolt length of bolt 200mm with dia of shoot / bolt complete all as specified and directed.

S&F 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed. complete all as specified and directed.

S&F 100mm size butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11, Size of hinges complete all as specified and directed.

S & F in repairs Continuous (piano) hinges, mild steel, bright finish or electro galvanised,width of flap (when open ) 40 mm. complete all as specified and directed.

S&F 125mm size extruded brass handles, febricated type polished , complete all as specified and directed.

S&F aluminiun (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed. complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples including necessary beadings complete all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples including necessary beadings complete all as specified and directed.

S&F mild steel work as for framed work such as grills gratings, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framed work of water tanks and similar work including necessary riveting and / or welding conforming to Fe 290 (Gde-E 165) complete all as specified and directed.

M&L for cutting grooves in brick wall 75mm wide and 65 mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

Taking down old existing water proofing treatment from top of RCC/arch slab including taking down of concrete padding or plaster and raking out joints of arch slab and hacking the top of RCC slab, cleaning with water and dispose off rubbish upto 200 meter complete all as specified and directed

M&L for providing PCC (1:2:4) type BO, (using 12.5mm graded crushed stone aggregates) as in roof padding finished fair and even without using extra cement complete all as specified and directed.

M&L, in repair, 18/19mm thick Soild WPC board, exterior grade, prelaminated one side with decorative choice laminations and other side balanceing white lamination, fixed with screws to WPC frame work in cup boards, rebated or flat edged fancy handle , Magnite lock complete all as specified and directed.

M&L for 18-20 mm thick machine cut perfect black granite stone slab on vertical surface, skirting / dado, cooking platform, jams, pillars and other similar works set and jointed in neat cement slurry and pointed in coloured cement to match the colour / shade of granite including necessary rubbing and polishing laid over & including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for rounding to edges of stone slabs two edge full round, such as in steps, cooking platform and other similar situation complete all as specified and directed

M&L for exterior grade, coloured, cement concrete designer chequered tiles of size 30cm x 30cm x 25mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment to match the shade / colour / matrix of tiles as in floor etc. laid over and inlcuding 20mm thick screed bed in CM 1:6 complete all as specifed and directed.

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed".

M & L for light shade vitrified tiles 10mm thick (square / rectangular) area of each tile exc 0.36 sqm but n.exc 0.42 sqm as in floors etc, set in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M & L for light shade vitrified tiles 10mm thick (minimum), (square / rectangular) polished, area of each tiles exceeding 0.36 Sqm (including 600mmx600mm size) but not exceeding 0.42 Sqm, as on vertical surfaces such as skirting / dados, set and jointed in neat cement slurry and pointed in white or coloured cement to match the clour of tiles and over and including 10mm thick screed bedding in CM 1:4 complete all as specified and directed".

M&L for Glazed ceramic coloured tiles of size 350mmx 250mmx7 mm / 450mm x 350mm x 7mm on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including rendering 10mm thick in cement mortar (1:4) complete all as specified and and directed

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazzo including cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete vertical surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M & L for applying 15mm thick rendering unsing ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @3% by weight of cement of as per manufacturer instructions, complete all as specified an directed. Note:-Water proofing compound shall be measured and paid sepratly Note Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge within 15 days of acceptance of contract.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and directed.

M&L for 10 mm thick screed bed in cement mortar 1:4 as in roof mixing with water proofing compound @ 3% by weight of cement or as per manufacturers instructions complete all as specified and directed Note :- Water proofing compound will be measured and paid seperately.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coat of white / tinted synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L Preparation of new plastered surface of wall by applying 3mm thick wall care putty and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified & directed.

M & L Preparation of Complete removal of existing treatmentplastered old surface of of wall and making the surface smooth Finishing walls and applying Acrylic Smooth exterior paint of required shade (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)using roller for painting complete all as specified & directed.

M& L Preparation of Complete removal of existing treatment by mechanical means plastered old surface of wall and applying 3mm thick wall care putty over one coat of primer and making the surface smooth and applying two coat of oil emulsion distemper using roller for painting complete all as specified & directed.

M& L Preparation of Complete removal of existing treatment by mechanical means plastered old surface of ceiling and applying 3mm thick wall care putty over one coat of primer and making the surface smooth and applying two coat of oil emulsion distemper using roller for painting complete all as specified & directed.

M&L for preparing the new plastered surfaces of wall by applying 3mm thick JK / Birla wall care putty and making the surface smooth and applying two coats of Oil bound distemper over a coat of primer using roller complete all as specified and direcrted.

M&L for preparing the new plastered surfaces of ceiling by applying 3mm thick JK / Birla wall care putty and making the surface smooth and applying two coats of Oil bound distemper over a coat of primer using roller complete all as specified and direcrted.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of old painted steel surface of any description over 10 cm in width or girth and applying two coat of white / tinted synthetic enamel paint complete all as specified and directed

M&L for 4 mm thick sheet glass, ordinary quality and glazing with oil putty or glazing pins in square exc 0.5 sq. m in each pane complete all as specified and directed.

Taking up or down GI water tubing 15mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Supplying and laying of 16mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings in trenches and wall complete all as specified and directed

Taking up or down GI water tubing 20mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Supplying and laying of 20mm dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings in trenches and wall complete all as specified and directed

Dismantling of old water tank exc 500 Ltr & n.exc 1000 Ltr capacity and Supplied, hoisted and fixed inposition rotational moulded polyethylence water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 500 Ltrs capacity with and including 20mm dia Ball valve high pressure of PTMT with apoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

Supply & fix in repairs 15mm dia chromium plated fancy type wall mixer with over head shower for mixing hot and cold water screwed , fixing and connection to pipes complete all as specified and directed. Make Cera Cat Part No F-1017401, Pearl Cat Part No ARI-015, Hindware Cat Part No. F740022

S&F in repairs 20mm bore dia Ball valve high pressure of PTMT with epoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm - 210 gms) complete all as specified and directed.

S&F pillar taps, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repairs stop valves, 15mm bore dia, cast copper alloy, Chromium plated with long shank and cup(concealed type) screwed down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F angular valve, 15mm bore dia, cast copper alloy, Chromium plated with long shank and cup(concealed type) screwed down,high pressure with crutch or butter fly handle,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supply and fixed in repairs gun metal globe or gate valves, 20mm bore dia, with iron wheel head ,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supplied and fixed in repairs CP towel rack 24" long complete all as specified and directed make Jaquar cat part No CAN-CHR-1181S or equivelent in Parko / Gem complete all as specified and directed

S&F in repairs Corner glass shelf (with brackets) set of three Make : Jaquar Cat Part No ACN 1173 complete all as specified and directed

Supplied and fixed in repairs CP toilet paper holder brass CP conforming to the sample kept in the office of Engr-in-Charge complete all as specified and directed.

Supplied and fixed in repairs CP soap dish brass CP conforming to the sample kept in the office of Engr-in-Charge complete all as specified and directed.

S&F in repairs towel ring 200mm dia chromum plated fancy type conforming to the sample kept in the office of Engineer-in-Charge.

Supplied and fixed in repair chromium plated long body bib cock with wall flange of 15mm dia (Make Jaquar-Cat part No FLR-CHR-5041N complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supplied and fixed 110mm bore UPVC(SWR) pipes single socketed in any length with rubber ring joint fixed to wall complete all as specified and directed.

Supplied and fixed 110mm bore dia UPVC(SWR) pipes single socketed in any length with rubber ring jointed laid in trenches complete all as specified and directed.

Supplied and fixed UPVC (SWR) bends 110 mm bore complete all as specified and directed

Supplied and fixed PVC (SWR) 110 mm bore junction, single(single 'T') equal or unequal complete all as specified and directed

Supplied and fixed UPVC (SWR) floor trap 110 mm bore including jointing to waste pipe with cement solvent fixed in cement concrete complete all as specified and directed

Supplied and fixed in repairs vitreous china WHB, white, flat back size 550x400mm including cutting for and pinning in ends of bracket or erecting stand with and including angle iron brackets, duly painted with two coats of synthetic enamel paint over one coat red oxide zinc chrome primer and providing cast copper alloy capastan head C.P brass pillar tap fency type 01 No 15mm bore, CP brass waste coupling 32mm dia, PVC waste pipe 32mm dia and PVC connection 450mm long high pressure with PTMT nut complete all as specified & directed. Make : CERA Cat Part No 52040113 (wash hand basin) & 52090106 (Pedestal)

Supply and fixing in repairs vitreous china squatting pan, Orissa' pattern, size 580 x 440mm white, with integral foot rests with and including cast iron 'P' or 'S' trap and setting the trap and pan in and including PCC 1:4:8, type D-2 minimum 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, making all connections complete all as specified and directed.

S&Fin repairs sinks with drainage board made of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F plate rack of stainless steel, sheet 1mm thick for kitchen overall size 1200x900x180 mm ,fixed with plugs and washers on wall complete all as specified and directed.

S&F glass shelf assembly 60 cm long , 5.5 mm thick glass , CP guard and fixed to wooden plug with CP screws and cup washer as specified complete all as specified and directed.

Dismantling of cast iron pipes or reinforced concrete pipes 100 mm internal dia of pipe complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) and including removal of debris & rubbish from the site complete all as specified and directed. Note : Stone slabs / tiles and hard core of any description shall not be measured & paid under this item.

Dismantling of wall or ceiling board (fiber,pulp,insulation etc) any thickness including cover fillets and removal from the site complete all as specified and directed.

Dismantling structural/framed steel work of any description as in purlin, rafter,grills, grating&doors etc. complete.

S&F in repairs 8mm dia, brass chromium plated health faucet with 1 meter long flexible hose and wall hook complete all as specified and directed Make : CERA - F8030301

S&F PVC Bath cabinet with mirror 18" x 22" x 4.25". Make : commander, Prayag or equivalent complete all as specified and directed

vibha associates

Shri Kanchan Engineers