CA NO. CWE SGNR-45 OF 2019-20 SPECIAL REPAIRS TO BUILDING NO. P- 14/03 AND 04 (OTM ACCOMMODATION) AND BUILDING NO. P-57/01 TO 12 (OLD MARRIED ACCOMMODATION) AT MILITARY STATION FAZILKA

Amount

Taking down chowkhats or frames with shutters without taking off shutters from the frame exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down shutters but area exceeding 1.00 Sqm and not exceeding 2.0 Sqm complete all as specified and directed by Engineer-in-Charge.

S & F Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M S square tubes , S&F in opening as per specification & drawing given in SSR-2009 complete all as specified and directed by Engineer-in-Charge.

M&L for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M S tubes for top & bottom rails M S frame shall be covered with heat moulded plain colour PVC ‘c’ channel having a PVC sheet strip of 20 mm width struck in side with solvent cement for stiles and plain colour PVC sheets 5 mm thick for top rail, lock rail & bottom rail on either side & as gap insert for tap rail & bottom rail, paneling of plain colour PVC sheets to be fitted in the MS frame walded/sealed to the stiles & rails with suitable PVC sheet beading and joined to getger with solvent cement supplying & filling in the frame at site as per specification & drawing given in SSR-2009 complete all as specified and directed by Engineer-in-Charge.

S & F stainless steel handle cast type anodized 150 mm long complete all as specified and directed by Engineer-in-Charge.

S & F stainless steel barrel tower bolt of extruded section and fixed 200 mm long complete all as specified and directed by Engineer-in-Charge.

S & F100 mm long butt hinges extruded aluminium alloy with galvanised mild steel hinges pin,anodised and fixed complete all as specified and directed by Engineer-in-Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified size of frame 125X60mm complete all as specified and directed by Engineer-in-Charge.

S & F pressed steel door frames with one or more rebates including necessary fixing lugs hinges lock strike plate etc complete all as specified size of frame 105X60mm complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No. 09 here in before but for size 75x60mm as in cup board frames complete all as specified and directed by Engineer-in-Charge.

S&F for guard square bars (primer coated) with 25mm x 3mm thick MS flat all round the frame of window / ventilator complete all as specified and directed by Engineer-in-Charge. Note : painting shall be measured and paid separately under appropriate item(s) of BOQ.

S & F Flush shutters,35mm thick,solid core construction,with block board core and plywood face panels,commercial type on both sides as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

M & L block boards 19 / 20mm thick, grade 2 quality, interior grade, decorative type with decorative face veneer on one face, fixed with screws to timber as in pelmet/shelves frame work with teakwood lipping 6 mm thick complete all as specified and directed by Engineer-in-Charge.

Taking down shutters and Refixing of shutters of any description exceeding 1.00 Sqm and n. exc.2.00 sqm each in the same opening complete all as specified and directed by Engineer-in-Charge.

M & L for Pieces, small let in for making good where hinges, etc. have been removed from chowkhals or frames, joinery, etc. including painting or oiling to match, if required complete all as specified and directed by Engineer-in-Charge.

M & L for Beads, straight (any size) for glazed or gauzed joinery, renewed, including mitres etc.. and removing old beads to Store complete all as specified and directed by Engineer-in-Charge.

S & F mild steel sliding door, bolts, plate type, stainless steel with bright bolt not less than 12mm bore, length of bolt 300mm complete all as specified and directed by Engineer-in-Charge.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, anodised aluminium frame for doors, window, ventilators with one or more rebate including joining cleat for fixing etc complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, anodised aluminium window/ventilator shutter side hug type without sash bar aluminium section wt 0.55 kg/mtr including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading screw anodised aluminium fitting such as peg complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, anodised aluminium grill of daimond size 100x100 mm of dia 6 mm including necesarry joining cleats, anodised aluminium snap beading screws complete all as specified and directed by Engineer-in-Charge.

S & F in repair aluminium window rescuring or easing and adjusting without taking down shutter any description exc 1.00 sqm but not exc 2.00 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down and refixing of aluminium window shutter of any size insame opening incl repairs/replacement of rubber packing glass clips & aluminium section ect complete all as specified and directed by Engineer-in-Charge. Note : The item glass glazing clip & aluminium section will be measured separately

M&L for hacking out old broken glass (any thickness, size, quality of description) from metal frame including punching or drilling out old glazing pins / springs complete all as specified and directed by Engineer-in-Charge.

S & F in repair galvanised mild steel wire cloth , 0.56 mm nominal dia of wie and average width of aperture 1.18mm, complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new wooden of wooden based surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engineer-in-Charge.

M & L for preparationof new steel surface over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old painted wooden surfaces of any description over 10 cm width of girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old painted steel surfaces of any description over 10 cm width of girth not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick work built in cement motor complete all as specified and directed by Engineer-in-Charge.

M&L Brick work with old size burnt fly ash bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 all as specified and directed by Engineer - in - Charge .

Demolition of Reinforced cement concrete (reinforcement cut as required to facilitate demolition) in floors / pavings, (below or above ground level) and of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge.

M & L mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking, hooking ends and binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and directed by Engineer-in-Charge.

M & L form work to soffits of suspended slabs such as roof slab and similar work not exceeding 200mm thick for rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

M & L form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces of concrete complete all as specified and directed by Engineer-in-Charge.

M & L RCC 1:1½:3, (nominal mix), type A-1, using 20mm graded aggregates as in Chajjas including TMT bars welded with existing steel complete all as specified and directed by Engineer-in-Charge.

M & L RCC 1:1½ :3, (nominal mix), Type A-1 using 20mm graded stone aggregates for slabs supported on walls, beams, columns and in shelves, the like complete all as specified and directed by Engineer-in-Charge.

Demolation of ashlar facings, dressed stone work, stone slabs or tiles from paving and precast concrete blocks and articles complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster/dado on brick wall including racking out joints, hacking for keys scrubbing down with water complete all as specified and directed by Engineer-in-Charge.

M & L rendering 15mm thick on fair faces of brick work in CM 1:6 finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L rendering 15mm thick on other than fair faces of brick work in CM 1:4 finished even & smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L10mm thick rendering in Cement Mortar 1:3 to ceiling surfaces finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Dismentling floor, hearth or wall tiling including cement mortar bedding (but not backing), remving serviceable tiles to stores and and rubbish off the permises complete all as specified and directed by Engineer-in-Charge.

M & L for glazed ceramic coloured joint free tiles 450 x 300 x 7mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade over 10mm thick cement sand screed (1:3) complete all as specified and directed by Engineer-in-Charge.

S & F Non - skid Ceramic joint free tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with joint free over 15 mm thick cement screed bed 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L marble work 18 to 20 mm thick in single piece (table rubbed and polished) in steps, jams, pillars, windowcills,cooking platforms and like in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade as approved complete all as specified and directed by Engineer-in-Charge.

M&L marble work 18 to 20 mm thick in single piece in riser of steps, skirting , dado, and pillar laid and jointed in cement mortor (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble shade as approved complete all as specified and directed by Engineer-in-Charge.

S & F stainless steel sink made of 1 mm thick for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortor on dwarf wall or including fixing in counter and connecteing union to pipe overall size 495 mm x 420 mm boel size 410 x 330mm x 160 mm complete all as specified and directed by Engineer-in-Charge.

S & F in repairs, Sink mixer with swinging spout ( wall mounted model) Chromium plated brass with connection and nuts complete all as specified and directed by Engineer-in-Charge. Make - ESSESS Cat part No- DE-12 or equivalent to Parryware / Nirali / Prayag.

S&F in repairs, 15mm bore brass chromium plated wall mixer with non-telephonic shower arrangement for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed by Engineer-in-Charge.

S & F vitreous china wash basin,white ,flat back ,size 550 x 400 mm including cutting and fixing in counter complete all as specified and directed by Engineer-in-Charge.

M&L Granite (of any type) tiles 18mm - 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over and including 20mm thick rendering in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, 20mm Ball brass valves, high pressure, with PTMT polytheene float and flynut complete, screwed for iron pipe orr brass ferrule and fixed in repairs complete all as specified and directed by Engineer-in-Charge.

S&F Rotational moulded polyethlene water storage tanks of capacity 500 Ltrs (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part- I including taking down of old tank of any size and description complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, bib taps, long body, 15mm bore dia, fancy type, cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed by Engineer-in-Charge.

S & F in repair MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-Charge.

S&F in repair brass chromium plated towel rail of size 60cm fixed with chromium plated brass screws and plastic cleats complete all as specified and directed by Engineer-in-Charge.

S&F grating square 150mm dia of PTMT (minimum weight 100 grams) complete all as specified and directed by Engineer-in-Charge.

S & F in repairs for brass chromium plated shower rose 125 mm size with swivel joint including fixing to 15 mm dia steel pipe or union complete all as specified and directed by Engineer-in-Charge.

Supply & fixing PVC connection both sides brass unions internal for size of 15mm size with PTMT nuts of length 450mm long complete all as specified and directed by Engineer-in-Charge.

S & F PVC waste pipe 32mm dia & 90 cm long complete all as specified and directed by Engineer-in-Charge.

M & L for preparationof new plastered wall surface and applying two coats of cement base paint complete all as specified and directed by Engineer-in-Charge.

Complete removal of existing treatment on walls and applying two coat of cement base paint including preparation of surface complete all as specified and directed by Engineer-in-Charge.

M & L Preparation of newly plastered surfaces by applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder and applying two coats of oil bound distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun complete all as specified and directed by Engineer-in-Charge.

M & L Preparation of Old plastered surfaces by removing old treatment and applying two coats of interior grade wall putty and making it smooth with sand paper by mechanical method i.e. with hand electric grinder then applying two coats of oil bound distemper over one coat of cement primer including all as specified by mechanical method i.e. spray gun complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of newly plastered surface and applying three coats of white wash on ceiling complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old decorative plastered surface and applying one coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge.

Dismantling of CI pipes or reinforced concrete pipes 100 mm dia fixed to wall etc complete all as specified and directed by Engineer-in-Charge.

Refixing Cast iron soil 100 mm bore , waste and vent pipes, in any length with or without ears with cement joints, laid in walls or in floors complete all as specified and directed by Engineer-in-Charge.

S&F Cast iron soil 100 mm bore , waste and vent pipes, in any length with or without ears with cement joints, laid in walls or in floors complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, (cast iron) 100 mm dia floor trap, plain with grating including jointing with solvent cement to connect waste pipe and fixed with PCC 1:2:4 complete all as specified and directed by Engineer-in-Charge.

Dismantling of CI pipes or reinforced concrete pipes 75 mm dia fixed to wall etc complete all as specified and directed by Engineer-in-Charge.

Refixing Cast iron soil 75 mm bore ,waste and vent pipes,in any length with or without ears with cement joints,laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S&F Cast iron soil 75 mm bore ,waste and vent pipes,in any length with or without ears with cement joints,laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S & F in repairs, 100mm cast iron sanitary connection socket to fit WC out-let complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 75mm bore Cast iron cowls, complete all as specified and directed by Engineer-in-Charge.

Taking down steel tubing 15mm bore and connections,including cleaning for refixing or remove to store complete all as specified and directed by Engineer-in-Charge.

Refixing 15 mm old steel tubing and connections in new or old possition (wall ceiling floors, etc.) complete all as specified and directed by Engineer-in-Charge.

S & F for 15mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor complete all as specified and directed by Engineer-in-Charge.

Taking down steel tubing 20mm bore and connections,including cleaning for refixing or remove to store complete all as specified and directed by Engineer-in-Charge.

Refixing 20 mm old steel tubing and connections in new or old possition (wall ceiling floors, etc.) complete all as specified and directed by Engineer-in-Charge.

S & F for 20mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor complete all as specified and directed by Engineer-in-Charge.

Taking down steel tubing 25mm bore and connections,including cleaning for refixing or remove to store complete all as specified and directed by Engineer-in-Charge.

Refixing 25 mm old steel tubing and connections in new or old possition (wall ceiling floors, etc.) complete all as specified and directed by Engineer-in-Charge.

S & F for 25mm bore medium grade tube galvanised with all fittings and fixed complete concealed including groove cutting for concealing to walls & ceiling or laid in floor complete all as specified and directed by Engineer-in-Charge.

S&F in repairs high density polyethylene (LDPE) pipes 40mm of presure rating 6kgf/sqcm complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, PVC (SWR) 110mm bore pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.

S & F in repairs Waste coupling for 40mm bore dia of discharge pipe of PTMT (half or full threaded) . (Minimum weight 45gms) complete all as specified and directed by Engineer-in-Charge.

Taking down eves and gutter and rainwater pipe complete all as specified and directed by Engineer-in-Charge.

Refixing PVC pipes (SWR) single socketed with rubber ring joints 110mm dia fixed to wall complete all as specified and directed by Engineer-in-Charge.

S & F in repairs PVC pipes (SWR) single socketed with rubber ring joints 110mm dia fixed to wall complete all as specified and directed by Engineer-in-Charge.

S&F in repairs PVC ( SWR) bends any radius bore of 110 mm complete all as specified and directed by Engineer-in-Charge.

M&L for PCC (1:5:10) type E-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete or filling in sunken floor complete all as specified and directed by Engineer-in-Charge.

M&L for Water proofing treatment to RCC sunken slab (not exceeding 45cm depth of sunken) as specified below complete all as specified and directed by Engineer-in-Charge. :- (a) applying 15 mm plaster in CM 1:3 with WPC on raised verticle surface (b) Cleaning the surface with wire brush/coir brush, removing lose material like dust particles, dirt etc. (c) Creating fillet coving of 50x50 mm with polymer modified mortar on the junction of slab and walls (d) Apply first coat of two component modified polymer coating on the horizontal and verticle surface (e) Provision of glass fiber mesh of 2 x 2 mm immediately on above coating (f) Apply second coat of two component modified polymer coating after 72 hrs (g) Cement concrete 1:4:8 over the coating as per requirment (h) Joining the saintary pipes with the water proofing tape having bridging ability of more than 1.5 mm (j) Filling the gap between the wall opening and saintary pipe with non shrink cementatious grout complete as specified.Plan area shall be measured

Supply and fix in repair PVC low level flushing cistern 10 litre capacity with flush pipe of polythene of low or high density of PVC 32mm dia, 60cm long and bracket etc and making connection including making good disturbed portion complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Vitreous China squatting pan of pattern “long pan”, size 580x450 mm white with ‘P’ or ‘S” trap, front or back inlet and foot rests, any pattern (excluding flushing cistern and flush pipe) complete all as specified and directed by Engineer-in-Charge.

Shotcreting 25mm thick in RCC coloumn, beams and slabs etc in layers with approved design mix concrete having the specified charateristic compressive strength (with ordinary portland cement coarse sand and graded stone aggregate of 10mm maximum size in proportion as per design criterial) in the cost of centering and shuttering at edges and corners etc as per direction of Engineer-in-Charge incl chipping of unsound/weak concrete material 50mm average thickness from slabs, beams, columns etc with manual chisel and /or by standred power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surfaces and reinforcement with wire brushes and thoroughly washing with water and allowing it to dry etc incl removal of rust by applying approved rust removal chemical & coating with Dr fixit epoxy zinc primer @ 6 sqm/ltr at DFT of 100 microns as per specification disposal of debries for all lead and lifts complete all as specified and directed by Engineer-in-Charge.

S&F for hard drawn steel wire fabric not exc 4Kg/Sqm cut to lengths, wire mesh to be fixed and firmly anchored to the concrete surface by means of "L" shaped mild steel shear key welded with existing reinforcement including the cost of materials, labour, tools and plants complete all as specified and directed by Engineer-in-Charge.

Dismantling of brick tiles or terracing tiles,single layer on roofs including cement motor complete all as specified and directed by Engineer-in-Charge.

Dismantling of mud in roofs,any thickness,including plastering and leeping (Whether full thickness removed or only a part thereof) complete all as specified and directed by Engineer-in-Charge.

Removal of mud to a distance exceeding 250m and n exc. 500m and depositing where directed complete all as specified and directed by Engineer-in-Charge.

M & L rendering 15mm thick water proofing plaster in CM 1:3 on slab / roof admixed including and with Dr. Fixit pidilite LW+@ 200 ml per bag of cement complete all as specified and directed by Engineer-in-Charge.

Supply only liquid water proofing compound complete all as specified and directed by Engineer-in-Charge.

M & L 25mm thick cement concrete flooring type B0 1:2:4 using 12.5 mm graded aggregate on roof slab complete all as specified and directed by Engineer-in-Charge.

Providing and applying microfiber reinforced UV resistant acrylic polymer coating three coats having solid contents 69% polymer content 35% & tensile strength 2.6 N/mm2 of Dr. Fixit newcoat /stat/parex or equivalent with a paint brush over existing roof surface after removal of all loose material lime dust etc with wire brushes from roof surfaces to get absolutely cleaned surface free of foreign contaiminantf flling of cracks wherever found with polymer based mortar, and after refairing the surface apply primer coat with Dr. Fixit prime seal polyester reinforced fiber net laid on the surface repair before executing the water proofing treatment complete all as specified and as directed by Engineer-in-charge. Note : The treatment shall be carried out by authorised applicator approved by CWE as per the manufacturer instructions complete all as specified and directed by Engineer-in-Charge.

M & L Endura Cool roof tiles 300 x 300 x 10 mm white vitrified water absorption < 0.5% SRI >90 (ASTME 1980, EN673 and En 411) BEPL (Building energy performance laboratory ) certified laid over screed bed or bedding layer of mortar 15 mm thick CM (1:4) complete all as specified and directed by Engineer-in-Charge.

Providing and applying rising damp proof coating system with single component ready to use damp proof coating Roff Hydamp complete all as specified and directed by Engineer-in-Charge. 1.SURFACE PREPARATION - Throughly brush and clean all laitance ,loose particles ,efflorescence,bird droppings etc all large voids or hollow portion must be removed.Non moving cracks having width up to 5mm most be filled with polymer based crack fillar. 2.APPLICATION :- Apply the first coat of Roff Hydamp with a paintbrush directly on the prepared surfaces.Allow to dry for a minimum 2-3 hrs.Apply one part of Roff Hydamp and 2 part of OPC white cement and make the putty.apply putty on the entire surfaces area.Allow to dry for atleast 3-4 hours.Apply the final coat of Roff Hydamp on the entire surfaces.

M & L for 50mm thick cement concrete type C2 1:3:6 (40mm graded aggregate) as in plinth protection complete all as specified and directed by Engineer-in-Charge.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in loose / soft soil complete all as specified and directed by Engineer-in-Charge.

M & L for 75mm thick PCC 1:4:8 , type D- 2, using 40mm graded aggregate as in sub base complete all as specified and directed by Engineer-in-Charge.

M&L for 80mm thick coloured (Red / Yellow) designed, machine pressed, precast concrete interlocking paver blocks (ISI Marked) (Factory Made) using grey cement and pigment and of any shape and size as directed conforming to IS-15658-2006 having compressive strength not less than 400Kg/Sqcm laid over and including 50mm thick layer of sand including filling the interstices complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:2:4, type B-1 , using 20mm graded stone aggregate as in kerbs or mud stops, rounded or chamfered on edges and similar work complete all as specified and directed by Engineer-in-Charge.

Excavation in post holes n exc 0.50m and getting out soft / loose soil complete all as specified and directed by Engineer-in-Charge.

S & F for framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel') complete all as specified and directed by Engineer-in-Charge.

S & F for mild steel screw bolts (machine made) 11 to 15mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed by Engineer-in-Charge.

S & F for 4 mm dia GI wire fitted with nut and bolt complete all as specified and directed by Engineer-in-Charge.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and directed by Engineer-in-Charge.

S & F in repair stainless steel plate rack of size of 900 mm x 775 mm x 250 mm made out of 1 mm thick stainless steel of first quality complete all as specified and directed by Engineer-in-Charge. Make Anupam international Model No KPR - 311 or Equivalent make and model approved by GE.

Demolition of cement concrete (un-reinforced) in floors / pavings, (below or above ground level) and of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge

M&L Cement concrete 1:3:6 type C–1 for filling of pressed steel frame and hold fast blocks etc all as specified .

Taking down chowkhats or frames with shutters without taking off shutters from the frame not exceeding 1.5 Sqm each complete all as specified and directed by Engineer-in-Charge.

S&F in repairs, steel ventilators fixed type 1.25mm thick Box Type (Primer Coat) ERW hollow "P" section of size 60mm x 25mm single rebated optional full glass or wire mesh complete all as specified and directed by Engineer-in-Charge. Note : Glass, wire mesh and painting shall be measured and paid separately under appropriate items of BOQ.

S & F in repair steel window 1.25 mm thick Box type (primer coated) ERW hollow P section of size 60 mm x 25 mm single rebated comprises gauged and glazed both skelton shutter ERW Section 50 mm x 20 mm and 1 mm thick with two open able leaf consisting two Nos of sash bars of flat iron 12 mm x 3 mm complete welded to frame with one vertical mullion of ERW box type T section of size 60 mm x 25 mm and 1.25 mm thick including cutting holes and making good dismantled portion in PCC (1:2:4) type B-1 four Nos for each window including following fitting welded to the frame shutter : (a) Hold fast 150 mm long of 12 mm x 3 mm made to shape - 04 Nos per window. (b) Handle of Z section 20 mm x 25 mm, 100 mm long 1 Nos per leaf. (c) MS tower bolt 150 mm long - 2 Nos per leaf. (d) MS pintol hings of size 100 mm x 14 mm - 2 Nos per leaf. (e) Z section 20 mm x 25 mm x 100 mm long stopper per leaf complete all as specified and directed by Engineer-in-Charge. Note : Wire mesh, glass and painting shall be measured & paid seperately under appropriate item(s) of BOQ.

S & F for 4mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 sqm in each pane complete all as specified and directed by Engineer-in-Charge.

S & F for figured glass 3mm thick pin head type and glazing with oil putty and securing with glazing pins not exceeding 0.50 Sqm in each pan complete all as specified and directed by Engineer-in-Charge.

S & F in repairs 15mm bore CP Angle cock one way chromium plated, high pressure, with crutch or butterfly handle, screwed both ends of iron pipe or for union and fixed complete all as specified and directed by Engineer-in-Charge.

S&F in repairs stop valve, cast copper alloy, fancy type,chromium plated with long shank and cup (Concealed type), screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe complete all as specified and directed by Engineer-in-Charge.

S&F in repairs gun metal globe or gate valve with iron wheel screwed both ends for iron pipe of 20 mm dia complete all as specified and directed by Engineer-in-Charge.

M&L 18mm - 20mm thick machine cut kota stone slab (table rubbed and polished) as in flooring laid over and including 15 mm thick screed bed or bedding layer in CM (1:4), set and jointed with grey cement slurry mixed with pigment to match the shade of slab including cutting, rubbing, grinding and mirror polishing upto desired satisfaction complete all as specified and directed by Engineer-in-Charge.

All as per Item No. 133 except kota stone slab only Jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing, grinding and mirror polishing upto desired satisfaction complete all as specified and directed by Engineer-in-Charge.

S&F in repairs drapry curtain rod 25mm dia, fancy type, fabricated out of mild steel sheet not less than 20 guage, including brackets and pair of decorated end knobs (finials), stop roller etc, pretreated powder coated natural color complete all as specified and directed by Engineer-in-Charge.

S & F for rotational moulded polythene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part I of capacity 1000 Litres including taking down old water storage tanks complete all as specified and directed by Engineer - in - Charge .

S&F in repairs vitreous china wash down water closet pan padestel pattern white including connection pipe to union of flushing cistern, inlet and overflow pipes,connecting only to flushing cistern anti-syphonage pipe with PVC flush pipe of 32mm dia and plastic seat cover with mild steel chromoum plated hinging and 'P' or 'S' trap device complete all as specified and directed by Engineer-in-Charge.

S & F in repairs, soap dish chromium plated brass complete all as specified and directed by Engineer-in-Charge.

S & F aluminium door stopper of any description completed all as specified and directed by Enginner-in-Charge.

S & F in repairs vitreous china urinal ,bowl type (back or corner wall type),flat back size of 465x355x265mm complete including providing and fixing plugs,bedding urinal agianst wall in cement mortar 1:2,securing urinal to plugs with and including 60mm long brass screws,pointing around urinal back in cement ,fixing automatic flusing cistern with brackets,flush pipe ,grating,water spreader and union for discharge pipe complete all as specified and directed by Engineer - in – Charge.

Taking down carefully existing aluminium/Copper point wiring light, fan socket or power bell complete with fitting such as sockets, ceiling roses, pendants batten holders regulators socket, call bells & making good to the disturbed surfaces of walls, matching the colour with existing Surface complete all as specified and directed by Engineer-in-Charge Note: Rate for making good shall be deemed to be included in above item rate.

Taking down unserviceable main switches and MCB distribution boards single phase complete all as specified and directed by Engineer-in-Charge

M & L for point wiring complete with 1.5 Sqmm (Nominal area) PVC insulated multustranded fire retardant (low smoke unsheathed and multicore copper conductor cable with colour code ISI marked and including PVC concealed conduict ISI marked and conduit fittings for one light point/fan point/5 Amps switch socket/bell/engagement light controlled by one switch including PVC insulated 1.5 Sqmm single core copper earth wire to common earth and connecting to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified and directed by Engineer-in-Charge Note : Cost of MS sunken box and bakelite sheet included in the rate

All as per Srl item No. 142 here in before but for one three pin socket outlet 5 Amps on the independent board complete all as specified and directed by Engineer-in-Charge

All as per Srl item No. 142 here in before but for one three pin socket outlet 5 Amps on the same board complete all as specified and directed by Engineer-in-Charge

All as per Srl item No. 142 here in before but with 1.5 Sqmm (nominal area) PVC insulated multistranded copper conductor cable unsheathed ISI marked controlled by two way switches complete all as specified and directed by Engineer-in-Charge

M&L for point wiring complete with 2.5 Sqmm (Nominal area) PVC insulated multistranded fire retardant low smoke unsheated and stranded copper conductor cable ISI marked in and including PVC concealed conduit medium quality and conduit fitting for 3 pin 15 amp multicore switch socket combination including PVC insulated 2.5 Sqmm single core copper earth wire to common earth and connected to earth dolly and including suitable MS sunken box of suitable size and covered with & including 3 mm thick bakelite, laminated hylem sheet top cover etc complete all as specified and directed by Engineer-in-Charge

S&F in repairs switch Piano type single pole one way 5 Amp, 230 VAC supply complete all as specified and directed by Engineer-in-Charge.

S&F in repairs switch Piano type single pole two way 5 Amp, 230 VAC supply complete all as specified and directed by Engineer-in-Charge.

S&F in repairs socket two in one ,3 Pin 5 Amps 230 VAC supply complete all as specified and directed by Engineer-in-Charge

S&F in repairs switch Piano type single pole one way 15 Amp on laminated sheet top cover complete all as specified and directed by Engineer-in-Charge Note : Sheet top cover incl in point wiring

S&F in repairs socket Pinao type 6 Pin 16 amp,230 VAC complete all as specified and directed by Engineer-in-Charge

S&F in repairs PVC Lamp holder suitable for and including batten fittings Watt with backalite 20mm back plate complete all as specified and directed by Engineer-in-Charge.

S&F in repairs LED Lamp 10 Watt retrofit and connecting complete all as specified and directed by Engineer-in-Charge.

M&L in repairs Ceiling Rose, surface bakelite 12 to 3 terminal, 240 volts, 5 Amp ISI marked complete all as specified and directed by Engineer-in-Chargecomplete all as specified and directed by Engineer-in-Charge.

S&F in repairs Electric bell ding dong complete all as specified and directed by Engineer-in-Charge

S&F in repairs bell push flush type 5 Amp, complete all as specified and directed by Engineer-in-Charge.

S&F in repairs fan regulator step down electronic type heavy duly flush type 230 volts AC single phase fixed on laminated sheet top cover (laminated top cover is included in point wiring) and connecting up complete all as specified and directed by Engineer-in-Charge Note : Laminated sheet top cover and sunken box is included in point wiring.

M&L in repairs LED 10W bulkhead fitting with IP-43 engineering plastic housing with clear ,single phase 240V, including 1.0sqmm copper flexible cable twiested three core alongwith flelxible PVC condiut from ceiling rose to fitting testing complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Exhaust fan of 300mm sweep mounted in suitable opening arrangement with louvers shutters suitable for operation on 230 volts, single phase, 50 cycle per second, AC supply and connecting up including three core PVC insulated PVC sheated copper conductor flexible cable 24/0.2mm drawn in flexible PVC conduit and fixed by using 4 Nos. 200mm long 12mm dia bolts, nuts and washers and grouted in wall in CM 1:3 complete all as specified and directed by Engineer-in-Charge

S & F in repairs MCB suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA and 5 to 32 Amps complete all as specified and directed by Engineer-in-Charge.

S & F in repairs MCB suitable for 240 volts AC supply, SPNwith over load and short circuit protection and rupturing capacity not less than 10 KA and 16 to 32 Amps complete all as specified and directed by Engineer-in-Charge

S & F in repairs MCCB TPN suitable for 40 Amp, 415 volts AC supply and short circuit protection and rupturing capacity not less than 25 KA complete all as specified and directed by Engineer-in-Charge.

S&F in repairs Distribution board double door made out of CRCA mild steel sheet surface with insulated material like polyester or with powder coating surface mounting SPN 8 way 240 volts with bus bar rating 200 Amps dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and directed by Engineer-in-Charge

All as per item No. 163 here in before but for TPN DB 4 Way complete all as specified and directed by Engineer-in-Charge.

Blanking plae of plastic complete all as specified and directed by Engineer-in-Charge Note : Suitable for distribution board

Earthing complete with galvanised steel earth platge electroe 60 cmx60cm6mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below normal round level) with edge of the plae not less than 1.5 mtr below normal ground level, connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and GI washers earth plate shall be surrounded by alternate layer of charcoal or coke and common salt 15cm thick all around bottom and top of earth plate as shown in electrical piate No. 3 of SSR Part-I and connecting to earthing test point and testing on completion including PCC 1:3:6 type C2 for earthing pit, GI light grade protection pipe of size 15mm dia, watering pipe 20mm bore medium grade, CI cover and frame necessary earth works and PCC work etc complete all as specified. Earth plate shall be surrounded by alternate layer of charcoal of coke and common salt 15cm thick alround the earth plate including bottom and top complete all as specified and directed by Engineer-in-Charge Note: PCC chamber shall be constructed at least 1.5mtr away from the earth electrod and pipe for watering shall be slanting manner

S&F LED tube light fixture,environmental friendly energy efficient ready to use 18W LED 6000k(4') complete with with all electrical connection complete all as specified and directed by Engineer-in-Charge

S&F Batten for LED tube light fixture with extruded aluminium heat sink,environmental friendly energy efficient ready to use with 18W LED 6000K(4') including electric connection with PVC copper flexible twin core cable,1.0 Sqmm from ceiling rose to light fitting complete all as specified and directed by Engineer-in-Charge

M & L for Sub main wiring with 2 single core 6 Sqmm PVC insulated FRLS cable with multicore copper conductor drawn into and including PVC conduit rigid non metallic of suitable dia with and including independent PVC insulated one run 6 Sqmm single core copper earth wire complete all as specified and directed by Engineer-in-Charge. Note:- Three lengths of 6 sqmm cable and will be measured as one length

Supply and installation of electric storage water heater 25 Ltrs of 5 Star Rating Vertically including temperature control system complete with all fittings and accessories,feroglass technology,incoloy glass coated heating element CfC Free high density PUF Insulation preventing heat loss,minimum five star rating complete all as specified and directed by Engineer-in-Charge Make: Bajaj / Havells / Crompton

S&F in repairs PVC connection wire woven with nickel plated brass adopter, both side threaded 45 cm long to the suitable size of geysers complete all as specified and directed by Engineer-in-Charge

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm for cold water connections to geysers complete all as specified and directed by Engineer-in-Charge -------------------------------------------------------------------------------------------------------------- Note : A sum of Rs. 1,36,055.00 will be deducted on account of credit for dismantled/ demolished / taken down material. Please refer details on Srl Page No. 36 & 37(R)(R) (Schedule of Credit) of Tender document

MANCHANDA CONSTRUCTION CO

SUDESH ENTREPRISES

SHARDA ENTERPRIES