SPL REPAIR TO PUF SH NO 254, 256 OFFR BLOCK , SPL REPAIR TO ELECTRICAL WIRING PUF SH NO 257,258,259,260, 261,263, 264 AT PMS

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for 15 mm thick cement plaster in cement mortar (1:6) as on walls, finished fair and even complete all as specified and directed.

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, mixed wth water proofing compound admixture (if directed) as per manufacturer's instruction,complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

Supply only liquid water proofing compound complete all as specified and directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n.exc 15cm thickness (below or above ground (level) and lowering if necessary, removal of the rubbish off the premises complete all as specified and directed.

M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr as specified.

M&L for old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 complete all as specified and directed.

M&L for old size brickwork with flyash bricks, straight or curved on plan exc 6m mean radius, half bricks thick built in CM (1:4) for edging of path complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing to low lying area and rubbish off the premises.

M&L Non Skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cemeent to match and including over screed bed or bedding layer of mortar 15 mm thick laying floor finished in CM 1:6 complete all as specified and directed.

M&L for Glazed ceramic tiles Coloured 450 x 300mm 7 to 8 mm thick in wall/dado etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match rendering over 10 mm thick in CM 1:3 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces complete all as specified and directed.

Supply and fixed in repairs floor mounted (single piece WC) bowl with cistern for coupled WC with and including UF soft close slim seat cover, hinges, dual flush cistern fitting, fixing accessories and accessories set complete of size 380x655x765 mm with S Trap- 250 mm, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Hand Shower (Health Faucet) (ABS Body) with 8mm Dia, 1 Meter Long Spirochrome flex tube & Wall Hook complete all as specified and directed.

S&F brass CP Tubular towel rail 20mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repair Paper Holder with Flap Recessed Type (Stainless Steel) complete all as specified and directed.

S&F vitreous china counter top wash hand basin (self rimming) leed NC0483 (Size 600 x 400 x 185 mm) colour brilliant / off white including fixing brackets and prepolished granite slab of size 1000 x 600mm size and cutting notch of required size as per the wash hand basin to be fixed in it complete all as specified and directed.

Supply and fixing in repairs brass chromium plated central hole basin mixer without popup waste system with 450 mm long braided hoses complete all as specified and directed.

S&F in repair Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as spd and directed.

S&F in repair 15mm bore fancy type stop valve/angle cock (multiple) , chromium plated concealed type cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repair PVC connection 15mm size PTMT nuts of length 450 mm complete all as specified and directed.

S&F as in repair bib taps cast copper alloy 15mm bore long neck body with fancy chromium plated screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F as in CP grating square 150mm size of PTMT(minimum 100 gms) complete all as specified and directed.

S&F as in CP grating square with waste hole 150mm size of PTMT(minimum 100 gms) complete all as specified and directed.

Supply and fixing in repair of PVC Mirror cabinet ,size 330x430 mm single door with mirror colour white complete all as specified and directed make as given inlist of makes as directed by Engineer-in-charge

Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as spd and directed

Taking down of chowkats or frames not exc 1.5sqm each with shutters (without taking off shutters from frames ) complete all as spd and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter (with particle board core), 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per Specification & drawing complete all as specified and directed.

S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x125 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately)

S&F for 35mm thick factory made single extruded WPC (wood polymer composite) solid wire gauzed i.e. panel will be of wire gauze in lieu of panel. The comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately)

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Taking down wall panelling and similar work complete all as spd and directed.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall panelling inclusive of fixing on to wall/ceiling to make PVC frame as per specification and drawing complete all as spd and directed.

S&F for solid PVC wall lining consisting of 5mm thick single side prelam colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing complete all as spd and directed

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasketetc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including Aluminium snap beading for glazing/ paneling, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410-W (Gde-E-250) quality-B complete all as spd and directed.

SS & F for Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts complete all as spd and directed.

S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 , the grill shall be inserted in the wall surface including necessary drilling and grouting with cement etc complete all as spd and directed.

S&F for 4mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as spd and directed.

S&F 100mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S&F 75mm long butt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 200 mm long Aluminium, anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as spd and directed.

S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as spd and directed.

S&F 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and dirceted.

Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 15 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete.

Taking up or down steel water tubings and fittings etc complete and making good disturbed surfaces of walls/ceilings etc for 20 mm bore pipe complete including stacking aside for reuse and removal of unserviceable items from site complete.

S&F 20 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F 25 mm outer dia medium grade CPVC, SDR 11 & plain CPVC SDR 11 with all fittings (brass inside the fittings) and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

S&F PVC SWR pipes 110 mm bore single socketed in any length with rubber ring joints laid in trenches or in floors all as specified and directed.

S&F PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F for PVC SWR bends of 110 mm bore complete all as spd and directed.

S&F for PVC SWR bends of 75 mm bore complete all as spd and directed.

S&F PVC (SWR) junction single (single T) equal or unequal provided with access door of 110 mm dia complete all as spd and directed.

S&F PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia all as specified

S&F for PVC (SWR) vent cowl 110 mm bore complete all as spd and directed.

Supply and fix in repair for Gun metal gate valve,20 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions all as specified and as directed.

M&L for prepration of new plastered surfaces and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer of any description not otherwise described over 10cm width or girth complete all as spd and directed.

M&L preparation of old surfaces of steel of any description over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as spd and directed.

M&L preparation of old surfaces of Puf insulated board of any description over 10cm width or girth, not otherwise described and applying two coat of synthetic enamel paint with Gun Spray complete all as spd and directed by Engr-in-Charge.

M&L for writing letters or figures (block, Roman, Italic or indian) n exc 30 cm complete all as spd and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as spd and directed.

M&L for PCC 1:3:6, type C1(using 40 mm graded crushed stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

Dismaltaling of plain or corrugated steel sheeting , any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as spd and directed.

S&F for Anodised aluminium snap grid (Size= 605mmx 605mm) frame work for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F for 6mm thick non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws complete all as spd and directed.

S&F mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges of sheet 1.25mm and 150mm dia or as directed.

S&F for PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls of 110mm dia and as directed

Demolation of RCC of any description and in any position not otherwise specifically provided for including (renforcement cut as per required to facilitate demolition) complete all as specified and directed.

M&L for precast RCC (1:2:4) type B-1using 20 mm graded crushed stone aggregate as in cover slab for manhole, set in cement mortar (1:4) complete all as specified.

M&L for preparation of surfaces, free from oils, grease, dust and loose or friable particles. paint, cement laitance and other poorly adhering contaminants and supply, filling, insulating, filling connection joints around window and door frames, pipe entries, air-conditioning vents and roller blind housings, vertical/horizontal construction etc by applying PU based 1-component, fast curing Multi-position, highly expansive polyurethane fixing foam with the help of gun, upto depth of 75mm and width not exceeding 20mm, complete all as specified'

Taking down carefully aluminium conductor point wiring (light,fan,socket or power) complete including fittings such as switches,ceiling roses, pendants, regulators ,sockets etc. and removing (except those to be reused shall be kept in safe custody at the site ) and making good disturbed surfaces of walls, floors etc.to match with the existing complete all as specified.

Material & Labour for point wiring complete with 1.5 sq mm FRLSH, PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral),drawn into and including PVC casing- caping (double interlock type) of not less than 20mm width with accessories and fittings such as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. for one light/fan/ bell point controlled by one switch i including pressed steel terminal flush boxes made out of 1.6 mm thick MS sheet suitable for modular switches concealed in wall , with and including modular cover plate with frame (suitable module) for housing the switches socket,outlet etc.,all as specified and directed by Engineer-in-Charge . and drawing 1.5 sq. mm copper solid conductor PVC insulated, unsheated cable as earth continuity conductor, connected to common earth and earth dolly , all as specified and directed by Engineer-in-Charge Note :- Cost of PVC casing & capping, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No 80.00 above but for one 6 pin multi purpose 5/6 Amps socket outlet on the same board with other switches.

All as per BOQ item No 80.00 here-in-before but for one power pointt using by 2.50 sq mm FRLSH,PVC insulated mlti stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 2.50 sq mm conductor for earth continuity (Green Colour) , on independent board ( but Not below the switch board of light points in the same vertical plane).

All as per BOQ item No 80.00 here-in-before but for one power pointt using by 4.00 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red Colour use for Phase & Black Colour use for Neutral), and with and including FRLSH,PVC insulated multi stranded copper conductor single core 4.00 sq mm conductor for earth continuity (Green Colour) , on independent board ( but Not below the switch board of light points in the same vertical plane).

Supply and Fixing Modular switch 6 Amp 1 way 1 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular switch 16 Amp 1 way with indicator 1 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular socket shuttered 6 Amp 2/3 pin combined 2 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular socket 16Amp multipurpose type 2 module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Modular Fan regulator step type 120 watts 2 Module size complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing Ceiling rose, surface bakelite 3 terminal, 240 volts, 5 Amps with back plate of 3 mm thick bakelite, complete, all as specified.

Supply & fixed in repair lamp holder, polycarbonatebody with back plate straight or angular suitable for batten fittings complete all as specified.

S & F in repair LED street lights nominal power 35 Watt, LED of Make Osram; Everlight; Philips; Nicha; Cree; Samsung, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, lumen efficacy of minimum 110 lumens per watt, built-in integrated electronic LED driver, output open /short circuit protection, phase to phase protection, over voltage protection, surge voltage protection upto 4 KVs, protection grade IP 66, CRI greater than 80%, CW available CCT of 5700K, power factor of minimum 0.95, pressure die-cast aluminium alloy housing with epoxy powder coated metallic silver finish after phosphochromate treatment, life span of minimum 50000 working hours including fixing at any height and including wiring using three core PVC insulated, PVC sheathed, flexible stranded copper conductor FR-LSH cables suitable for outdoor use, 1.5 sqmm as per IS 694: 2010 complete all as specified and as directed.

S&F in repairs LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. Note (i) Make of batten and LED tube lamp should be of same make.

S&F in repairs LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting including taking down old unserviceable complete all as specified & directed. Note : Make of batten and LED tube lamp should be of same make.

Supply and fixing in repair ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) without remote. (Old U/s ceiling fan to be deposited in MES E/M Store Yard)

Supply & fixing in repair exhaust ventilation fan with louvers of sweep 250mm,230 volts 1200 Rpm, with blade and frame and louvers sturdy engineering plastic complete ,ISI marked complete all as directed by Engr-in-Charge. (Old U/s exhaust fan to be deposited in MES E/M Store Yard)

Supply and fixing for surface type sub main wiring with two run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including drawn into and including PVC casing- caping (double interlock type) of not less than 25mm width with accessories and fittings such as bends, elbows, tees, crosses, junction box etc, fixed on wall/ceiling with GI saddles, GI screws, rawl plugs etc. including one run of 4.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC casing caping shall be measured as unit length. (ii) Cost of PVC casing caping, conductors, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

S & F sheet metal enclosure for MCB, DB, TPN 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 8 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43 , IK 09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed by Engr-in-charge.

Supply and fixing in repair 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixed in repairs MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

Supply and fixed in repairs MCB TPN 40-63 Amps, 'C' series 10kA, 415 Volts and to be housed in DBs complete including necessry connection all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

Taking down old ceiling fan of any capacity/sweep after disconnecting the electric supply from any site, checking for its electrical defect and opening fans for checking of mechanical defect after dismantling of fan, carry out repair/over hauling including removing dust and grease, and cleaning of internal mechanical parts of fan with kerosene oil, checking of alignment of shaft, oiling and greasing, preparing Surfaces Cleaning Dust and Oil using Steel Brush and Soap Water, filling Cavities with Filler and applying One Coat DUCO Paint with Spray Machine including Writing MES No. in Black Paint, and re-assembling, and connecting/refixing of fans in its original position by providing new GI nut bolt, lock washer and lock/split pin complete all as specified and directed by Engr-in-charge. NOTE: (i) Replacement of defective parts like rubber bush, split pin, nuts, bolts, sprng washers, check nuts etc as required are deemed to be included in the item rate.

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (medium grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 15mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI wire and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate