Construction Of Cycle Shed In Front Of East Land Bajaria In Eastland

Amount

Excavating over areas not exceedind 1.5 M deep and getting out in Soft/ loose Soils etc. complete all as specified and directed.

Excavation in trenches, n exc. 1.5M wide and n. exc. 1.5M in depth, for foundation etc. or for shafts, wells, cesspits, manholes etc. n. exc. 10 Sq. M. on plan and n. exc. 1.5m in depth and getting out in Soft/ loose Soils etc. including trimming bottom and sides of trenches, levelling/grading and ramming bottom of excavation complete all as specified and directed.

M & L, Cement concrete in foundations, filling and mass concrete Type-C-2, 1:3:6 (40 mm graded aggregate) all as specified and directed.

M & L, R.C.C. (nominal Mix) Type-B-1,1:2:4 (20 mm graded Aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete.

M&L, Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surfaces of concrete all as specified and directed.

M&L, Form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits ( if any) of foundation and plinth beams; and similar work;vertical or to batter for fair finished surfaces of concrete all as specified and directed.

M & L, CEMENT CONCRETE IN SUB-FLOORS, SUB-BASES, FLOORS AND PAVINGS, ETC. Cement concrete type B-1, 1:2:4 (20mm graded aggregate); 145 mm thick .

Finishing Cement concrete surfaces even and smooth without using extra cement.

M&L, Mild steel TMT bars 10 mm dia and over,cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dial or securing clips all as specified and directed.

M&L, Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length,bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dial or securing clips all as specified and directed.

S&F, M.S. screw bolts (machine made) with Gexagonal or square heads at one end and screwed the other, or screwed both ends, each screw end to be fitted with washers and one end hexagonal or square nut; length of bolts exc 22.5cm and n exc 30cm long, diameter of shunk 16 to 20mm and all as specified and directed.

S&F, M.S. screw bolts (machine made) with Gexagonal or square heads at one end and screwed the other, or screwed both ends, each screw end to be fitted with washers and one end hexagonal or square nut; length of bolts exc 10cm and n exc 15cm long, diameter of shunk 16 to 20mm and directed.

S & F, Rolled mild steel in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 all as specified and directed.

S&F, Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed..

S&F, Pre- painted galvalume aluminum zinc coating GI based plain sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / ridge/ velly guller/ cladding to wall, fixed with self tapping screws all as specified and directed.

M&L, PAINTING STEEL AND IRON SURFACES: Preparation of New or previously untreated surfaces of any description, over 10cm in width or girth, not otherwise described, Priming with Aluminium Red Oxide and applying Two Coats of Aluminium Paint all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm - Soft/loose soil all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and directed.

AMARNATH ENTERPRISES (BID ID -730535)