Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹25.4 LAccepted-AOC | L1 | Accepted-AOC Lowest | |
| 2 | L2₹27.8 L+₹1.6 L (6.29%)Rejected-Finance | L2 | Rejected-Finance Other then lowest | |
| 3 | L3₹28.5 L+₹2.3 L (8.78%)Rejected-Finance | L3 | Rejected-Finance Other then lowest | |
| 4 | L4₹28.6 L+₹2.5 L (9.37%)Rejected-Finance OFFICE 2ND FLOOR MEHRA TOWER TIBRI ROADD GURDASPUR 143521 | GURDASPUR | PUNJAB | 143521 | L4 | Rejected-Finance Other then lowest | |
| 5 | L5₹29.4 L+₹3.3 L (12.4%)Rejected-Finance | L5 | Rejected-Finance Other then lowest |
Tender Value
₹41 L
EMD Value
₹82,000
Closing Date
6 Sept 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Gurdaspur
Garrison Engineer, Gurdaspur Mil Stn
Certain repairs and sunken treatment to Md Accn Yadunath and Manekshaw enclave and OTM accn at Fd Regt under AGE B/R-I, GE Gurdaspur.
2022_MES_543864_1
GE GSR-17/2022-2023
Open Tender
Civil Works
Item Rate
240 days
GE Gurdaspur
As per Tender Documents
8 documents required · 8 mandatory
₹500
GE Gurdaspur
₹82,000
28 Sept 2022
6 Aug 2022
13 Sept 2022
6 Aug 2022
6 Sept 2022
25 Aug 2022
Amount
Demolition of cement concrete of any description and in any position not otherwise specifically provided for sunken floor, plinth protection, flooring, paving, foor kerb etc. all as specified and directed.
M&L plaster 15mm thick in cm 1:3 in sunken portion of slab on fair faces of brick work or concrete surfaces using waterproofing compound all as specified and directed Note : Water proofing compound shall be measured and paid separately.
Supply only integral water proofing compound.
M&L APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on primed surface with bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area/ sunken floor with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed.
M&L applying evenly a tack coat of blown type or residual bitumen of grade 85/25 at the rate of 1.2 kg per sq.m complete all as specified and directed.
M&L for PCC 1:5:10 type E2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete in sunken floor complete all as specified and directed.
M&L 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed.
M&L for ceramic glazed dark shade coloured tiles of size 350x250x 7mm/ 450x350x7mm thick joint free on and including 10mm thick screed bed in CM(1:4)set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado including taking down existing tiles with bedding complete all as specified.
M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 including taking down existing tiles with bedding complete all as specified.
Material and Labour for repairing to RCC projections, chajjas, roofs, facia, ceiling etc. by scrapping, cutting, chiseling, de-rusting and cleaning exposed reinforcement of damaged loose RCC surfaces and applying neat cement slurry @ 3kg/sqm and filling the surfaces with cement sand mortar 1:3 or cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) using coarse sand in layers as required and reinforced with 8mm dia. TMT bars in patches area n.exc 5 Sqm each and thickness of RCC member exc 50mm including applying two coats of finishes to match with the existing surfaces at height upto 12m complete all as specified. Note:- Cost of formwork shall be deemed to be included in unit rate quoted by the Contractor.
Taking down cement plaster of any description on brick walls on concrete surfaces etc including racking out joints hacking for key,scrubbing down with water etc from walls and ceiling surfaces of any description complete all as specified and directed.
M&L for rendering 15mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces of walls, finished surface even and fair with WPC upto height 12m complete all as specified and directed. Note : WPC shall be measured and paid separatel
M&L for rendering 12mm thick plaster in cement mortar 1:6 on brick or concrete surfaces of walls, finished surface even and smooth without using extra cement complete all as specified and directed.
M&L preparation of new plaster surface and applying two coats of Oil bound distemper of wall over a coat of primer on wall complete all as specified and directed.
M&L preparation of new plaster surface and applying two coats of cement base paint of wall on wall complete all as specified and directed by EIC.
Repairs, resecuring, easing & adjusting of shutter without taking down shutters of any description exc. 1.00 sqm & n.exc. 2 sqm each.
Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter for the chowkats) complete all as specified and directed.
Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.
Taking down chowkats with shutter exc 1.50 Sqm but n exc 4.00 sqm each (without taking off shutter for the chowkats) complete all as specified and directed.
S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock strike, plate etc complete of size 105mmx60mm including two coats of synthetic enamel paint over a coat of red oxide primer and filling PCC 1:2:4 type-B0 (using 12.5mm graded stone aggregate) in the frames complete all as specified and directed.
S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.
S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed.
S&F 35 mm thick both faces covered with decorative face veneers with lipping to match, factory made Flush shutters, solid core construction, with block board core and decorative face panels as decided by GE, on both sides complete all as specified and directed.
S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.
S&F 35mm thick second class hard wood (Hollock), glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, sizes of members of shutters as specified in SSR Part-I section 8 clause 8.24(a) supplied and fitted to chowkats complete all as specified and directed.
S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/ beads complete all as specified and directed.
S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/ beads complete all as specified and directed.
M&L for preparation of new wooden surface exc. 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed.
M&L for preparation of new steel surface exc. 10cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.
M&L for preparation of old painted steel surface exc. 10cm width or girth and applying one coat of synthetic enamel paint height upto 12m complete all as specified and directed.
Hacking out old broken glass panes of any thickness, size or description from wooden frame or stone concrete or steel frame,or brick surrounds, glazed with putty or fixed with beads and prepared to receive new glass panes complete all as specified .
S&F 4mm thick sheet glass ordinary quality and glazing with oil putting in squares n.exc. 0.50 Sqm each.
S&F 4.8 mm thick black sheet glass ordinary quality and glazing including neoprane gasket in square or rectangular in size n.exc 1.00sqm each in aluminium door or window shutter complete all as specified and directed
S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate complete all as specified and directed. Note : Repair required on steel door frame, welding to be carried out or necessary alternative arrangements to be done.
S&F Aluminium anodized barel tower bolt of extruded section 200mm long ISI marked complete all as specified and directed.
S&F extruded aluminium alloy handle fabricated type anodized of size 150 mm long complete all as specified and directed.
S&F extruded aluminium alloy handle fabricated type anodized of size 100 mm long complete all as specified and directed.
S&F 100mm size medium weight mild steel butt hinge fixed with metal surface through bolts, screws or welding complete all as specified and directed.
S&F 100mm size medium weight extruded aluminium alloy butt hinge fixed with metal surface through bolts or with screws complete all as specified and directed.
S&F 300mm size aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.
Supply and fixing in repair cutrain rod 20mm dia of mild steel with PVC coated with fixing brackets, stops, rollers etc fixed to wall with screws, PVC plug complete all as specified and directed.
M&L in repair for block boards, 25mm thick, grade 1 quality, exterior grade, , decorative type with decorative face veneer on both faces, fixed with screws to timber frame work for shelves, partitions and shutters.
S&F 75mm size hasp and staple safety type stainless steel with hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.
S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with integral foot rests, including connection to trap and flushing pipe, etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed.
S&F in repair PVC low level flushing cistern 10ltr capacity, with syphonic action PVC float valve, brackets and 32mm bore PVC flush pipe complete all as specified and directed.
S&F in repair PVC connections 15 mm size with PTMT nuts of length 600mm complete all as specified and directed.
S&F in repair stop valves or angel valve 15mm bore cast copper alloy fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.
S&F GI tubing 15mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down existing pipe complete all as specified and directed.
All as per Srl item No 48 above but fixing only (old serviceable pipe re-used).
S&F GI tubing 20mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings ISI marked including taking up and down existing tubing complete all as specified and directed.
S&F GI tubing 32mm bore medium grade, fixed to wall/ceiling or floor etc with all fittings including taking up and down existing tubing complete all as specified and directed.
S&F Grating doom 125 mm dia with waste hole of PTMT. complete all as specified and directed.
Dismantling of cast iron ,PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches , if required.
S&F PVC (SWR)pipes 110mm dia in any length with rubber ring joint fixed to wall/floor complete all as specified and directed.
S&F PVC (SWR)pipes 75mm dia in any length with rubber ring joint fixed to wall/floor complete all as specified and directed.
S&F in repair PVC (SWR) bends 110mm dia, in any radius, complete all as specified and directed.
S&F in repair PVC (SWR) bends 75mm dia, in any radius, complete all as specified and directed.
S&F in repair 110mm bore PVC(SWR) junction single (Single T), (equal or unequal ) with access door complete all as specified and directed.
S&F in repair 75mm bore PVC(SWR) junction single (Single T), (equal or unequal ) with access door complete all as specified and directed.
S&F in repair PVC (SWR) vent cowl of size 110mm.
S&F in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 100mm dia of outlet complete all as specified and directed.
S&F in repair for PVC(SWR) floor trap plain with grating including jointing with solvent cement 75mm dia of outlet complete all as specified and directed.
M&L 110mm bore PVC (SWR) 'P' or 'S' trap including jointing with solvent cement
S & F Stack clamps (110 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.
S & F Stack clamps (75 mm pipe) out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.
S&F rotational moulded polytheylene triple layered white water storage tanks of capacity 500 Litres (cylindrical vertical with closed top) hoisted and fixed in position including dismantling of existing water tank complete all as specified.
S&F 1000 litres capacity rotational moulded polyethylene triple layer water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition including dismantling of water tanks complete all as specified and directed.
S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule 20mm bore.
S&F in repair stop value 20mm bore cast copper alloy with butterfly handle screwed down for high pressure, screed on bath ends, fixed with iron pipe etc complete all as specified and directed.
S&F in repair bib tap 15mm bore cast copper alloy chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed.
S&F in repair brass CP shower rose 125 mm size with 100mm arm swivel joint fancy type complete all as specified and directed.
S&F in repair brass chromium plated towel rail 60 cm long fixed to wall complete all as specified and directed by Engr-in-Charge.
S&F in repair vitreous China wash basin, white flat back, size 630x 450mm including brackets, waste coupling of PTMT (half or full threaded) bore dia of discharge pipe 32mm (Minimum weight 45gms) complete all as specified and directed.
S&F in repair PVC waste pipe 32mm dia 800mm to 1000 mm long fixed to wash fitting of wash basin and sink all as specified and directed.
S&F in repair Pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore.
S&F in repair stainless steel sink with draining board, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc. overall size 915mm x 480mm with bowl size 410mm x 330mm x 160mm with stainless steel coupling and necessary fixing arrangment complete all as specified as directed
Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc .
M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed.
M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed.
M&L for cement cocnrete type B-1 (1:2:4) (using 20mm graded stone aggregate) as in plinth protection thickness 50mm finishing the surface even and fair complete all as specified.
M & L for Green Marble work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and including 15 mm thick screed bed in CM 1:4 incl pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl dismantling of marble complete all as specified and directed.
M&L for vitrified tile 10 mm thick joint free (square/ rectangular) area of each tile exceeding 0.18 sqm to 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 including taking down existing tiling and bedding complete all as specified.
M&L for rendering 15mm thick in cement mortar 1:4 on brick or concrete surfaces of roof finished even and fair with WPC including roughing the surface of old concrete floor picking sweeping clean and washing down with water to remove dust/mud etc.and brushing neat cement slurry @ 3kg/Sqm complete all as specified and directed. Note : WPC shall be measured and paid separately.
M&L for PCC 1:2:4 type B1 (using 20mm graded stone agg) as in roof kerbs or mud stops, rounded or chamfered on edges with WPC complete all as specified and directed by Engineer-in-Charge. Note : WPC shall be measured and paid separately.
M&L for rendering 5mm thick plaster on ceiling in cement mortar 1:3 finished surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.
M&L preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed by EIC.
S&F steel window box type made of ERW tube, hollow P section of size 60mmX25mm double rebated outer frame comprising double skeleton shutters i.e. guaged & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and FI 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 including taking down old existing window complete:- (i) Thickness of the sheet shall be of 18 gauge (ii) Hold fast,150mm long of flat iron 12mmX3mm- 04Nos per window (iii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iv) MS Tower bolt 150mm long-02 Nos per leaf (v) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (vi) Cleat 55mm long of hollow square 15mmX12mm -01 Nos per leaf (vii) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (viii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). Note: Wire cloth, glass, painting shall be measured and paid for separately
S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts, including taking down old existing window/ ventilator complete all as specified and directed. Notes: (i) Thickness of the sheet shall be of 18 gauge. (ii) Glass/ wire mesh, painting shall be measured and paid for separately
S&F anodised aluminium door shutters, aluminium section weighing average not less than 1.00kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. including taking down old existing shutters complete all as specified.
S&F anodised aluminium window/ ventilator shutters side hung type without sash bars, aluminium section weighing average not less than 0.75 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) ncluding taking down old existing shutters complete all as specified.
S&F anodised aluminium frame for doors, windows, ventilators, with one or more rebates including joining cleat for fixing etc. including taking down old existing frame complete all as specified
S&F in repairs Mortice lock ,aluminium vertical type size 65mm 2 levers complete all as specidfed and directed.
M&L for petty repair to existing in built Aluminium Door, locks, hinges including making the lock/Glass/ adjusting shutter complete serviceable all as per existing pattern as directed by Engineer-in-Charge including provision of duplicate keys as required.
S&F in repair aluminium (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.
S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed
S&F in repairs vitreous china wash down water closet (pedestal pattern) fixing with bolts ,white colour, including connections to flushing pipe, anti-syphonage pipe, etc. including making good to floor complete all as specified and directed.
S&F in repair vitreous china urinal bowl, flat back size 465x365x265mm white, with grating & union for discharch pipe etc.(excluding flushing cistern and waste pipe) with all necessary fittings complete all as specified & directed.
S&F in repair brass spindle with nylon washer and removing leakage of water of any concealed type suitable for 15 to 20mm bore pipe complete all as specified.
S&F in repair tap/valve head/ handle 15mm dia cast copper alloy fancy type chromium plated round/square hole complete all as specified and directed.
S&F in repair stainless steel L-type jet spray with 1m hose pipe for fitting in WC complete all as specified and directed.
Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof/wall coverings complete all as specified and directed by EIC.
S&F in repair Aluminium, 0.56 mm thick plain, sheet, alloy 31000H4 in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood /steel/Concrete framing with 40 mm lap joints with riveted or screwed, including bending or turning up, mitred angles, etc. as required complete all as specified and directed.
S&F Machine cut kota stone slab flooring 20-22mm thick over cement screed base 20 mm thick in CM 1:6 jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) including dismantling existing slab complete all as specified and directed.
S&F Vitreous china coloured WC italion finish pedestal pan with attached vitreous china flushing cistern push button type having dual flushing system of same colour including PVC seat cover same colour including cast copper alloy Jet chromium plated with PVC connection 15mm bore 450mm long with brass CP nuts complete all as specified and directed.
Note: A Schedule of Credit for old/unserviceable demolished/dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.
M/s kulwant singh and sons
P S BUILDERS
talwinder singh and co
KAILASH CONSTRUCTION CO
JOGRAJ CONSTRUCTION COMPANY
M/s SODHI SALES CORPORATION
M/s. Nirmal Singh
D.RAJ And CO.
M/S GAGAN CONSTRUCTION CO
stage.html
html • 0.07 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .