PROVN OF COVERED SHED AT ENTRANCE GATE AT TARAMOUNT ADDN ALTN TO BLDG NO P 57 AT HQNC AND REPAIR REPLACEMENT OF CERTAIN BER SUMMER WINTER APPLIANCES AND PROVN OF INSTALLATION OF 10 GEYSER FOR SINGLE OR ACCN AT BLDG NO NP 03 UNDER GE SOUTH UDHAMPUR

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc. 1.5 sqm each and removing to store complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n.exc 4 sqm each and removing complete all as specified and as directed

Taking down cement plaster of any descreption on brick/stone walls or concrete surfaces including racking out joints, hacking for key scrubbing down with water etc on walls and ceiling, complete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed

Rolled mild steel Fe-410w (Gde-E-250) quality 'B' Roof trusses (framed ) , trussed, purlins, crane gantries , rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces cleats etc complete all as specified and as directed

Rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to grade Fe.290.Gde-E-165, steel work duly painted with one shop coat of zinc chromate primer including preparation of surfaces complete all as specified and as directed

Mild steel framed work such as grills, gratings with ends of bars shouldered or reveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, frame work of water tanks and similar works, conforming to Fe-290, Gde E-165, complete all as specified and directed by Engr-in-Charge/GE.

Preparation of new steel surfaces of any discripton not otherwise discribed over 10 cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide on steel surfaces complete all as specified and as directed

Pre-painted galvatume aluminum zinc coating GI vased corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with coach screw and washer in roof, wall etc complete all as specified and as directed

75 mm thick PCC 1:4:8, type D-2 by using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

75mm thick cement concrete type C-2, 1:3:6 using 40mm graded aggregate as in subbase complete all as specified and as directed.

25mm thick PCC type B-1, 1:2:4, using 20 mm graded crushed stone aggregate as in sub base finished fair for receiving floor finishes complete all as specified and as directed

Dura stone heavy duty vitrified tiles of size n exc 0.36 Sqm of 8-10mm thick as in floors set and jointed in neat cement slurry and pointed in white cement to match the surface and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Granite stone 18-20mm thick (table rubbed and polished) in window cills, cooking platforms and the like not less than 1 Sqm (in one piece), laid over 15mm thick layer of cement mortar 1:3 after roughening of existing concrete surface and applying a layer of neat cement slurry @ 3Kg/Sqm including pointing in white cement 1:2 using marble dust with admixture of pigments to match with shade of stone, including demolition of stone slabs and tiles of any description or thickness in floors etc. laid, bedded and pointed in any mortar complete all as specified and as directed.

PCC 1:2:4 Type B2 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified.

vitrified tiles light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM 1:6 complete all as specified and as directed.

Digital glossy finished double charged Vitrified tiles light Shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in vertical surfaces as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed in CM 1:4 complete all as specified and as directed.

Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with mixture of white and grey cement in equal proportion & no pigments including 15mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, jointed with grey cement and no pigment complete all as specified and as directed.

Preparation of old /New plastered or unplastered surfaces of wall by applying 1 to 1.2mm thick Altek/Birla white putty to obtain smooth/even finish using sand paper and applying two coat of anti-fungal acrylic emulsion paint (Appex) any tinted, complete all as specified and directed by Engr-in-charge/GE.

Aluminum alloy powder coated (50 micron) anodized door frame of section 100 mm x 44 mm x 2mm thick,door shutter of aluminum section of size 85 mm x 44 mm x 2 m thick, top rail and both styles of size 100mm x 44 mm x 2mm thick,lock rail and bottom rail of size 115 mm x 44 mm x 2 mm thick including aluminum anodized snap beading and rubber packing,& 5 mm thick colour designer glass including, 200 mm long tower bolt-2 Nos, 200 mm long Aluminium handle-02 Nos on each leaf, 4 lever lock brass 100 mm long mortice lock & double action floor door spring heavy duty suitable for shutter for each leaf complete all as specified and as directed.

Powder coated (50 micron of approved colour) Aluminum anodised double shutter window (glazed and wire gauge) side hung with aliminium window frame or chowkat 1.50 mm thick sheet & section aluminium anodised of size 100 mm x 44.50 mm and window shutter frames made of (middle, top rail, bottom) and styles 1.5 mm thick aluminium anodised sheet & section of size 44.5 x 44.5 mm including aluminium grill and all fittings such as rubber gasket aluminum glazing clips locking cabinet and 75 mm handle and including 4 mm thick tinted glass pane in panes glazed shutter fixed with rubber gasket and glazing clip/aluminium beads and with stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel staples on gauge shutter including aluminium tower bolt 75mm 02 Nos in each shutter, aluminium hinges 100mm B-12) 02 Nos in each shutter, aluminium handle 100 mm 01 No in each shutter including all accessories complete all as specified and as directed.

Aluminium alloy powder coated (50 micron) anodized frame of section 85mm x 44mm x 2mm thick as in aluminium partition including aluminium anodized snap beading and rubber packing, partly glazed with 5mm thick tinted glass and partly with 12mm thick prelaminated particle board, complete all as specified and as directed.

Brick work with sub class 'B' bricks exc 6m mean radius straight or curved on plan built in cement mortar 1:6 including demolition of old brick/stone masonry complete all as specified and as directed.

Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:4) including finishing the surfaces fair and even without using extra cement complete all as specified and as directed.

Rendering 15 mm thick on brick or concrete surfaces of walls in CM (1:6) including finishing the surfaces fair and even without using extra cement complete all as specified and as directed.

Applying 1 mm thick layer of wall putty on walls to give uniform surface, surface scrubed with emery paper and make surface good and clean complete all as specified and directed.

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces

M&L for two or more coats of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification complete all as specified and as directed.

Excavating in post holes ( or similar holes ) each n. exc 0.5 cum in soft /loose soil getting out, returning filling in and ramming around in layers not exceeding 25cm complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power/ LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling complete all as directed.Keeping the LED lights in safe custody complete all as specified and as directed.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as specified and directed.

Taking down Old/ Unserviceable MCB DBs TPN / Main Switches by disconnection of electric connection including old unsv MCCBs,MCBs, isolators etc and making good to distrubed surface complete all as specified and directed.

Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly as specified.Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish.

All as per srl item No 39 but for 3 pin 6 Amps socket outlet independent board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly.

All as per srl item No 39 but for 3 pin 6 Amps socket outlet on the same board including PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly.

All as per Srl item No 39 but for 3 Pin 16 Amps socket outlet independent board with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly.

Modular switch 6 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge/GE.

Modular switch 16 Amps single pole one way 230 V, 50 Hz, AC , with inner/outer plate complete all as specified and directed by Engr In charge/GE.

Modular Bell push flush type 6 amp 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge/GE.

Modular socket 3 Pin 6 Amps flush type 230 V, 50 Hz, AC , with outer/inner cover complete all as specified and directed by Engr In charge/GE.

Modular socket combined 2-in-1, 6 Pin 6 & 16 Amps 230 V, 50 Hz, AC , flush type with outer/inner cover complete all as specified and directed by Engr In charge/GE.

Ceiling rose, surface bakelite 65x 50mm two to three terminals fixed on PVC Round Blockcomplete all as specified and directed by Engr In charge/GE.

Calling Bell ding dong 230 volts single pole 50Hz complete all as specified and directed by Engr In charge/GE.

Electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as spcified and directed.

Single pole and neutral enclosure surface mounted 240 voltswith 2 pin and earth plug and socket with one single pole MCB 20 Amps with indicator of complete all as specified and directed.

S&F in replacement 36W (2 x 2) LED Ceiling/recess light panel for recess mounting warm white colour which provides soft-light and glare free symmetrical illumination complete all as specified and as directed.

LED lights fitting 1x 20W, 230V,AC decorative box type warm white colour with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type warm white colour with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

2X2 Feet Square shape 24 watt 220 volts AC surface mounted type warm white colour with high efficiency soft light and symmentrical illumination complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge/GE.

LED luminaire 10 watt, 220 V AC recess/surface mounted downlighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp warm white suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-Charge/GE.

Decorative wall mounting 1X9W fixture with frosted glass along with 9W warm white bulb GLS lamp luminaire complete all as specified and directed by Engineer-in-Charge/GE.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 12 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed.(Note-MCBs will be measured separately)

S & F in replacement MCB single pole 240 volt any rating from 10 to 40 amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed.

S & F in replacement MCB single pole and neutral 240 volt any rating from 63 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2X6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2X10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 2X1.5 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 1.00 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc complete all as specified and as directed.

Stop valve brass chromium plated screwed down for size 15mm pipe ISI marked complete all as specified and directed.

PVC flexible connection graded suitable for hot water, 450mm long (Set of two) for inlet/outlet connections of geysers with heat resistance washers and nuts complete all as specified and directed.

15mm bore GI pipe medium grade galvanised , with all fittings and fixed complete all as specified and as directed.

Supply and fixing bib cock brass chromium plated screwed downfor size 15mm dia GI pipe complete all as specified and directed.

Ceiling fans complete with blades, down rods, (including electronic fan regulator/ remote operation as directed by Engr-in-Charge) and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five starrated with brushless direct current motor(BLDC) Complete all as specified and direceted by Engr-in-charge/GE.

Ceiling fans complete with blades, down rods, (including electronic fan regulator/ remote operation as directed by Engr-in-Charge) and accessories, 230 V, 1400mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five starrated with brushless direct current motor(BLDC) Complete all as specified and direceted by Engr-in-charge/GE.

SINGH CONST CO (BID ID -3096445)

M/S ASHOK KUMAR PACHIALA (BID ID -3099445)

M/S AUM TECHNO (BID ID -3116351)

m/s sushila devi (BID ID -3102228)