Construction Work

Amount

Installation Charges inclusive of Transportation to site and the Bored pile equipment employed for the works including setting up of pile driving equipment with all accessories and tools at each of the pile location based on the sequence of operation approved by the departmental Engineers irrespective of the location and distance involved in movement of pile driving equipment etc., complete complying with standard specification and as direct by the departmental officer

Installation of Vertical bored cast in situ RCC piles of basic length 20 RM in all types of soil with M30 Grade using Ready Mix Concrete (Sulphate resistant Cement), Supply and erection of reinforcement, shoe, fabrication, including cost of binding wire, cutting, tying, welding and placing the reinforcement cage in correct position, driving and removing the temporary casing pipe of full depth, shifting the plant and equipments from one point to another, carryingout any ancillary work adjacent to piling work, trimming the concrete above cutoff level, cleaning the debris and levelling the site etc, as directed by the Departmental Engineers.

The Rig capacity,height of Towerand length of casing pipe etc., must be adequate to take care of change in soil profile. The length of pile for payment shall be measured from top of shoe to the bottom of the pilecap. Testing of Concrete as specified in IS 456/2000 acceptance criteria as per clause 16.1. Frequency of testing as per 15.2.2. Testing to be conducted at both the ends at site as well as RMC plant. Pile driving depth should be decided by the departmental officers at site.

600 mm dia pile having longitudinal main reinforcement of 5 Nos 20# + 5 Nos 16# with helical reinforcement at 10 # @ 200mm C/C with inner rings of 12 # @ 1000mm C/C with lifting hook of 12 # at required length.

Initial Load Test as per IS 2911 Part IV 1985 including cost of single pile (250% of pile capacity), labour, reinforcement charges and all other incidential charges including excavation, shoring, strutting, dewatering etc. as necessary hire charges for jacks, measuring devices, Structural Frame work for platform, Kent ledges etc, as required and providing pilecap.

Routine load test as per IS 2911 part IV 1995 (150% of pile capacity) including labour charges for jack, measuring devices, structural frame work plot form, kent ledges etc., as required and as directed by the departmental officers etc. complete.

Earth work excavation for foundation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2 mts. and clearing and levelling the site, etc., complete complying with standard specification.

Providing, laying, spreading and compacting graded stone aggregates for Wet Mix Macadam 250mm thick, including premixing the materials with water at OMC in mechnanical mix plant, conveyance of mixed materials by tipper to site, laying in uniform layers using pavers in Sub Base/ Base course on well prepared surface and compacting with vibratory roller to acheive the desired density including cost of material, labour charges, rentals for machinery, fuel and all other incidental charges etc., complete as per clause 406 of MORTH Rev-5

Supplying and filling in foundation and basement with filling M-sand in layers of not more than 15 cm thick, well rammed watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Cement Concrete 1:3:6 (One Cement, Three Crushed Stone sand (M-Sand) and Six hard broken stone jelly) and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Cement Concrete 1:5:10 (One Cement, Five sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and Filling with conveyed earth in layers of not exceeding 30cm thick, well rammed and consolidated including watering using power roller by hire basis etc., The rate is conveyance charges, loading and unloading, refilling charges and hire charges for power roller machine etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with crushed stone dust in layers of not more than 15 cm thick, well rammed watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Brick work in Cement Mortar 1:5 (One cement and five sand) using Fly Ash Bricks of 230 x 110 x 70mm size conforming to IS:12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing, etc.,complete complying with standard specifiction.

For foundation & basement

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Supplying and erecting centering for sides and soffits including necessary supports and strutting upto 3.29 M height for plane surfaces as detailed below in all floors with all cross bracings using Mild Steel sheets of size 90 x 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm x 25mm x 3 mm for boarding laid over silver oak joists of size 10cm x 6.50 cm spaced at abote 90 cm centre to centre and supported by casurina props of 10cm to 13 cm dia spaced at not more than 75 cm centre to centre etc. complete complying with the standard specificaiton. (Payment for centering shall be given after the concrete is laid)

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.,

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

Providing additional strutting to centering of RCC slabs of plain surface for every additional 1.0 metre height or part thereof but not less than 30 cm, over the initial 3.00 metre height from floor level using casurina props of 10cm to 13cm dia including cross bracing etc., complete complying with standard specification and as directed by the department officers.

Providing and laying in position, Standardised Concrete Mix M-20 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/mᶾ and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m.) 7670 kg. of sand,

but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation & Basement

Providing and laying in position, Standardised Concrete Mix M-30 Grade in accordance with IS:456-2000,using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kglms and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of sand,

but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For Foundation & Basement

Ground Floor Super Structure

First Floor Super Structure

Second Floor Super Structure

Third Floor Super Structure

Fourth Floor Super Structure

Fifth Floor Super Structure

Sixth Floor Super Structure

Seventh/Terrace Floor Super Structure

Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire)

Brick work in Cement Mortar 1:6 (One cement and six sand) using Fly Ash Bricks of 230 x 110x70mm size conforming to IS:12894-1989 Class designation not less 50 kg./ sq.cm. average compressive strength in cement mortar 1:5 for load bearing structures for foundation and basement and for superstructure including curing,etc.,complete complying with standard specifiction.

Ground Floor Super Structure

First Floor super Structure

Second Floor Super Structure

Third Floor Super Structure

Fourth Floor Super Structure

Fifth Floor Super Structure

Sixth Floor Super Structure

Seventh/Terrace Floor Super Structure

Brick partition walls of 11cm thickness using Fly Ash Bricks of 230 x 110 x 70mm size in cement mortar 1:3 (one cement and three sand) including charges for fixing Hoop iron reinforcement if found necessary including curing etc., complete and as directed by the departmental officers. (The cost of hoop iron reinforcement shall be paid separately)

Ground Floor Super Structure

First Floor super Structure

Second Floor Super Structure

Third Floor Super Structure

Fourth Floor Super Structure

Fifth Floor Super Structure

Sixth Floor Super Structure

Providing granolithic floor finish of the 50mm thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

Providing, mixing, laying polymer based water proofing treatment for the Sunken Toilet / Lift well / OHT Rcc wall by applying cement based, flexible, waterproofing compound confirming to IS:2645, to a thickness of 1mm of the prepared surface of the roof slab / floor slab as per specifications mentioned above providing cement mortar 1:3, waterproofing cover plaster to a thickness of 12mm over the membrane coating with admixture of approved make. Rate quoted is inclusive of preparation of surface, which includes cleaning of surface polymer mortar curing, labour, tools and equipment, etc. Rate inclusive of grouting with cement and sand required for the treatment, the cost and labour charges for fixing 25mm dia pressure pipes 15kg/cm2 to a length of 45cm for drip pipes, etc. complete.

Brick Jelly Lime Concrete of 1:2:5 (One Lime,Two Sand and Five Brick jelly ) with 40 mm hand broken brick jelly for Sunken portions including dewatering wherever necessary and laid in layers of not more than 15cm thick, well rammed, consolidated and curing etc. complete complying with standard specification.

Weathering course concrete using best quality broken brick jelly of size 20mm uniform gauge in pure slaked lime in the proportion of brick jelly to lime being 32:12-1/2 by volume and laid over the RCC roof slab in a single layer and consolidated to the required finished thickness by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling jaggery and lime water etc. complete complying with standard specification.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Supplying the flooring with new Vinyl flooring approved quality and brand including labour charges , it shall be self leveling 3.00 mm anti static seamless PVC flooring. Floor shall be smooth, non-slip, impervious material conductive enough to dissipate static electricity but not conductive enough to endanger personnel from electric shock. It shall be Electro Static Discharge (ESD) combat PVC seamless flooring of very high quality thickness not less than 2.00 mm . Continuous roll shall be used and with minimum joints. The Joints to be welded by special PV thermal units using PVC welding bars of same colors. The Sheet shall be highly durable to shock and indentation. It shall be scratch proof, inert to body fluids, chemicals and disinfectants & shall not be affected by the temperature variations. The Flooring shall be done by skilled workers of the accredited agencies, authorized by the supplier of PVC sheets. The Electrical resistance (Point to ground ) shall be within 2.50x104 to 5x 106 Ohms.

The Floor shall not allow build-up of Electrical charges beyond 100V due to antistatic effect. The corners shall not be terminated sharply & concealed coving shall be used to overlap the wall panel to a height of approx. 25mm &sealed perfectly & uniformly. Self leveling compounds shall be used the Conductive copper grid laid underneath the PVC sheet shall be supported by liquid epoxy compounds allowed to set as a uniform and level surface. The copper strips to be made visible by grinding and no copper strips shall project more than 05.mm above level surface to avoid damage to the PVC sheet. One earthing lead shall be brought out from every 150 square feet area and attaching it to the main earthing strip/ Ground. The Copper grounding strips (0.55mm thick, 50mm width) shall be laid flat on the floor in the conductive adhesive and connected to copper strip of grounding.

The connection from copper grid shall be brought out uniformly at places to from equi- potential grid. The flooring shall be mechanically shock proof, scratch proof, flame retardant and anti-bacterial. The floor shall efficiently discharge Electric charges up to 2KV. The Floor shall offer Electrical Resistance. The Final Surface shall be non- corrosive to biological fluids & detergents, shall be fire retardant & anti - microbial, color shall be uniform, pleasant & matching with ambience etc. complete complying with standard specification and as directed by the departmental officers etc. complete.

Paving the floor with best quality Double Charged Vitrified Tiles 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three sand)20mm thick in all floors and the top pointed with the white cementmixed same colour pigments etc., complete complyinE withstandard specification. (The make and brand ofthe tiles should beJohnson / Kajaria / Somany / Nitco / RAK which has to be gotapproved by Executive Engineer before use on works)

Flooring with Self design Joint free rectified Ceramic Tiles of size 305 x 305 x 6mm laid over 20mm thick cement mortar 1:3 (Onecement and Tree sand) base mortar over the existing slab / floorincluding cutting the tiles to the required size with special cutter wherever necessary, laying in positionand and pointing with whitecement mixed with colouring pigment at the rate of 0.3 kg. / sq.m.etc., complete complying with standard specification. (The makeand brand of the tiles should be Johnson / Kajaria / Somany / Nitco/ RAK or Equivalent which has to be got approved by executiveEngineer before use on works)

Dadooing walls with Joint free rectified Colour designed digital print ceramic tiles, with borders, with size of 300mm x 600mm x 8mm and above setin Cement Mortar 1:2 (One Cement and Two sand) 20mm thick andpointing the joints with white cement mixed with colouring pigmentsat the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc,complying with standard specification and as directed by thedepartmental officers. (The make and brand of the tiles should belike Johnson / Kajaria / Somany / Nitco / RAK or Equivalent whichhas to be got approved by Executive Engineer before use on works)

Clading the walls by supplying and fixing of White Galaxy or equivalent quality of granite vertical slab for an average thickness of 17 mm to 20mm for vertical surface over a base layer in cement mortar 1:2 10 mm thick and pointing with the same mortar as directed and agmi, Aroldate and POP Paste for fixing the granite slab in position wherever necessary. The quality and colour of granite slab should be got approved by the Executive Engineer before use on works

Supplying 18 to 20 mm thick white jet blck granite partition slab for urinals of 1200 x 600 (Avg) mm size fixing to wall using 3Nos.of suitable chromium plated brackets with CP bolt and nets, washers, cutting to required shape polishing to all the expose and surfaces and edge grinding etc, complete as directed by the dept officers.

Providing grooving to granite slab at the intermediate edges of the vertical face with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Providing Double semi nosing to granite slab at the edges of the vertical space with neat finishing etc complete with standard specification and as directed by the departmental officers. The cost including higher charges of machines and labour charges etc complete

Providing and Fixing of PVC Trims (Corner beeding) at the outer corner profiles of the tiles including cost of material, labour and handling etc. as directed by departmental engineers at site of work and as per standard specification.

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct.

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc.,with Cement Mortar 1:3 (One Cement and Three Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:5 (One cement and Five sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly 'Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after

it is dry and finishing the surface smoothly,etc.,complete complying with standard specifications and as directed by the Departmental Officers.The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The wall putty shall be got approved by the Executive Engineer before use of work).

Textured wall painting with exterior weather proof emulsion paint (2 coats) of approved quality and colour over a priming coat including through scrapping, clean removal of dirt etc., complete and including necessary plaster of Paris, putty whereas required as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Supplying and fixing Teak Wood frames for doors Windows and Ventilators using required MS angles, flats and rods of approved design and as directed by the departmental officers including cost of MS Grills, labour charges and cost of one coat of red oxide primer with labour charges for priming coat etc. complete complying with standard specifiction.

supplying, hold fast of M.S flats of over all size of 330x50x6mm suitably folded to the required L shape have two end of lap of 50mm long each and overall length of the horizontal portion as 230mm & including making necessary grooves in two end laps to accomadate screws etc., complete.

Supplying and fixing in position of Teak wood door shutter using spl quality teak wood planks of 40 mm thick panelled doors with required raw materials, Brass hinges, Brass tower bolt,ornamental Brass handles, Door stopper, Door closer,Brass aldrops and bush with suitable locking arrangements etc. The rate should be inclusive of cost of materials, labour charges for wrought and put up the doors with kadasal charges and transporting charges etc complete complying with standard specification and as directed by the Departmental officers.

Providing and fixing of 1.2mm thick Lead Lining Door for X-Ray Rooms, Scanning Rooms with Mild Steel Door Frames 105mm x 57mm X 18 G and 12 G x 50mm Shutter made of GI with PWG finish and honey wool insulations with SS 101mm x 75mm x 3mm SS 304 Ball Bearings Butt Hinges, Mortice Sash Lock ML 100A, 50mm BS, 85mm centre, CL 207 : Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make), Heavy Duty Door Closer, Frames fixed wih walls using Mortice Sash Lock ML 100A, 50mm BS, 85mm centre CL207: Key & Knob 70mm, 5 Pin Cylinder with Handle SS Finish (Dorma Make) all neccesary accessories and fittings as per the required and as per the approval for the Department Officer Sqm. 13000.00

Providing Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc., complete complying with standard specification and as directed by the Departmental officers.

Supplying, fabricating and fixing in position factory made Stainless Steel Flush Door Shutter 35mm thick using SS 304 Grade 1.6 mm thick, Stainless Sheets on both sides (Equivalent to IS 6911-04 Cr. 19, Ni 9) minimum 8-8.5% nickel and 18% chromium sourced from original stainless steel manufacturer with view panel size 30mm x 45mm made up of 6mm thick clear toughened glass fitted with double side adhesive tape and finished with dowconing silicon sealant, floor spring for each shutter, consealed tower bolt, suitable stainless steel locking arrangement and other necessary furniture fittings of approved quality. The vertical styles and other frame members and cross stiffeners shall be of same quality stainless steel box section of suitable size and thickness with proper core material as prescribed by the Departmental Officers

Supplying and fixing in position of best quality and approved make Stainless Steel Sink of size 1800mmx600mmx600mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia Brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specification excluding CI brackets. The sink and specials should be got approved by the Executive Engineer before use on works).

Supply and erection of Double Leaves Fire Rated Door with Frame having the dimension of 1800mm x 700mm with following specifications. A.Door Frame 1.6mm: Galvanized 120 GSM branded make JSW b.Door leaf 1mm: Galvanized 120 GSM branded make JSW c.Shutter Thickness: 46mm d.Honeycomb: In-fill e.Glue Macroplast UR-7221 f.Door Hinges: 4" x 3" x 3mm, Double Ball: Make Assa Abloy Yale Ball bearing Butt Hinges Grade SS304 - Finish SS g.Door Closer with Standard Arm Finish:Silver h.Lock Set: Dead Lock with both side key i.Door Orientation: To be confirmed by client j. Mounting of door: Brick wall mounted k. Powder Coating : Powder coated in standard RAL paint colour of PO Red (60 to 90) Microns

l.Single Point Panic Bar (2 Horizontal): Make Assa Abloy Yale or Equivalent m. Dead Lock with both side key: Make Assa Abloy Yale or Equivalent n.Vision Panel 200 x 300mm 2 Hrs. Fire Glass Schott Pyran with Frame 0.Rated Glass Schott Pyran with Frame p.Anchor Bolt with Endcaps The above assembly mounted on concrete or brick wall including the cost of cutting, chipping, concrete packing, plastering, scaffolding all other conveyance as per standard methods and as directed by the Departmental Officers.

Supplying and fixing in position of Solid core Flush shutters with Teak ply on one side and commercial ply on other side with teak wook lipping alround 35 mm thick of applied shade and hot pressed bonded with liquid phenol formaldluide resin with internal lifting with TW as per IS 2201/ part I /1991 The rates inludes the labour charges for fixing the shutter to the frames and for fixing furniture fiitings.The rate include the cost of furniture fittings etc complete

Single Leaves

double Leaves

Polishing the teak wood shutters with two coats of Melamine polish to wood surface as per direction etc., complete should be got approved by the Executive Engineer before use on works.

Supplying and fixing of wood polymer composite (WPC) door with solid door frames extruded with size 75mmx50mm. The inner core made of rigid WPC compound with minimum shore hardness of 55 and buld density 750kg/cub.Mt. The frame shall be fixed to the wall using 10x10mm long MS screw throught the frame by using PVC fasteners. A minimum of 4nos screw to be provided for each vertical members, Door Shutter of 25mm thick Wood Polymer Composite (WPC) single core Extruded Door Shutter, with one side digital printing of specified Design which is approved by engineering-in-charge. Both side of the shutter shall have rough sugar texture finish, laminated with UV oil. The solid WPC board shall have minimum shore hardness of 55 and Bulk density 550kg/cub.Mt moulding the thickness remains 25mm (+/-1mm) etc. complete as per the direction of the departmental officers.(make Qute / Equivalent)

Supplying,fabricating and fixing in position of aluminium powder coated finish door fully PLB Board 12 mm thick Sliding door using rectangular aluminium box section of sizes of frame section 101.60 x 44.45 x 3.18 mm @ 2.399 Kg./M Shutter Sections Top and Middle Section 50 x 44.45 x 2.50 mm @ 1.292 Kg./M, Bottom Section 100 x 44.45 x 2.50 mm @ 1.974 Kg./M, Vertical Style 50 x 44.45 x 2.50 mm @ 1.292 Kg./M with necessary accessories such as aluminium clips, handles,lock and sliding channel with wheel set including all materials, labour and power consumption charges required for fabrication if necessary clipping,

dismantling materials necessary holes in RCC column beams or masonry wherever necessary with power drill to the extent required and made good to the original conditions after fixing etc. complete. The aluminium surface is to be anodized with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than 15 microns (Fifteen) for all sections. All the materials should be got approved by the Executive Engineer before fixing in position as directed

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to

the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI 1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Supplying and Fixing Hydraulic Door Closer of various sizes of approved quality using Aluminium Extruded section body tubular type universal hydraulic door closer with double speed adjustment like DORMA (or) equivalent (with ISI Monogram)

Hydraulic Floor springs of various sizes double acton hydraulic floor sping of approved quality, brand, manufacture asper BIS standards for doors including cost of cutting floors as required, embedding in to floors and Stainles Steel Cover plates with Aluminium Pivet and single piece M.S. sheet outer box with side plate etc., capaple of taking upto 130 Kg. weight from door shutter, like HARDWYN make (U-32) or its euivalent with ISI monogram.

Manufacturing, Supplying and fixing of Steel doors with following specification. MS Angle of size 40 x 40 x 6mm at 3.5 kg/m used for outer frame and MS Angle of size 35 x 35 x 5mm at 2.6 kg/m for the shutter frame. Stiffeners with 32 x 6mm at 1.5 kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame. 18 GCR Sheets of best quality is laid as panel in the shutter frames. 18 x 5mm at 0.70 kg/m MS Flat is welded over the 32 x 6mm at 1.50 kg/m MS Flat on the rear side of the door, sand witching the CR Sheet for rigidity. Additional stiffeners with 18 x 5mm at 0.7 kg/m MS Flats are provided diagonally on the rear side of the shutter. 2 Nos. of hinges in case of single leaf and 4 Nos. of hinges in case of double leaf shutters is provided. 6 Nos. of hold fasts 200mm length spliced at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. one at the top and the other at bottom

Supplying and fixing of M.S. grill of approved design for open courtyard, grill, grill work to doors and window openings etc., using necessary mild steel flats for inner and outer members which should be fixed on edges including cutting the members, welding, grinding, one coat of priming coat using best approved quality red oxide primer,dismantling of walls /concrete if necessary, fixing and finishing the dismantled portion to original condition etc., complete complying with standard specification.

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. he supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification.

160mm dia

110mm dia

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 Part I to IV in stages to suit the progress of work consist as per the detailed specification as below.(Measurements taken for the plinth area for the purpose of payment) including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing, etc., complete and as directed by the departmental officers.(The chemical should be got approved by Executive Engineer before use on work)

.Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete, in bottom and sides of foundation.Stage-2: Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth.Stage-3: Spraying anti-termite chemical solution on the sand for the flooring before laying the flooring concrete. This treatment has to be carried out on the sand filling by making holes with crow bar to a depth of 60cms and at 60cms intervals on both direction and at junction of wall and flooring thoroughout.Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment

Providing and fixing 8 mm thick fully designed perforated calcium silicate board 2'x2' panel tiled false ceiling (Hilux) including supplying and fixing true horizontal level false ceiling with 24mm prelude grid system Using hot dipped galvanised steel section exposed surface chemically cleaned caping prefinished in backed polyester paint wall angle of size 3000x19 x19mm used in the periphery of the ceiling fixed to the wall, parttion with the help of screws at 600mm c/c. Mainrunner of size 3000x24mm suspended at a 1200mm c/c by using securely fixed to the structural soffit of RCC slab by using 6mm Nylon Rwl plug at every 1200mm(max)and 1200mm long cross tee of size 1200x24mm to interlocked between mainrunner at 600mm c/c(max) to form a grid of size 1200x600mm.600mm long cross tee of size 600x24mm is inserted to form a grid of 600x600mm and finally laying classic lite regular edge tiles of size 600x600x15mm

Supply and fixing of GYP Board false ceiling using 12.5 mm thick of approved quality and design suspended from the ceiling using "U" shaped Galvanised iron channels at 1.20 M centre to centre on both longitudinal and cross direction for vertical support and fixing "U" shaped G.I channels at 0.90 m centre to centre on longitudinal direction respectively for horizontal support by using T.W reapers at corners and at intermediately and fixing of plaster of paries on the panel provided as per design / patttern given by the site officer and finishing the ceiling surface with some plaster of paries materials etc. Necessary openings should be made for providing spotlights, florescent tubes in the ceiling by using plywood 12 mm thick and opening should be covered with Acrylic panel complying with standard specification and as directed by the departmental officers etc. complete. All the materials should be got approved before use on work by the Executive Engineer.The rate is including two coats of plastic emulsion painting over the wall coat primer etc., complete.

Supplying and Laying Rubber Moulded paverblock of 60-63mm thick with new one using cement concrete 1:2:4 for manufacturing, finishing, Curing and conveyence to site and laying etc., complete complying with standard specification and as directed by the deparmental officers.

Suppling and fixing position of polycorbonate sheet roofing with following specification. The roofing made of 10 mm thick multi wall polycarbonate sheet roofing with following specification. The roofing made of 10mm thick multi wall polycarbonate sheet with approved colour (Lexan branded) double sided UV coated using MS frame work consists of main truss 50 x 50 mm MS square pipe for vertical support in the base plates and top connecting plate for fixing truss. The rate including cost of 10mm thick multi wall polycarbonate sheet, MS truss work, MS vertical support pillars, Horizontal purlins, Aluminium plate for bottom & top with sealent for all joint of sheets and labour charges for all fabrication works and sheet fixing work and necessary Scaffolding cost and painting work for all MS Truss with purlin etc., completed. and as directed by departmental officers.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of 75mm thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.

Manufacturing, supplying and fixing in position plain cement concrete precast kerb slab of size 600mm x 600mm x 100mm in Cement Concrete 1:2:4 (One cement, Two sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three Sand) to full depth of slab etc., complete complying with standard specification and as directed

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 110mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete complying with standard specifications and as directed by the departmental officers. (The water closet should be got approved by the Executive Engineer before use on works).

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC /12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings,

such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition,etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Executive Engineer before use on works) Floor Fitting

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best quality and approved make Indian made white/colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works.

20 mm dia UPVC Pipe

25 mm dia UPVC Pipe

32 mm dia UPVC Pipe

40 mm dia UPVC Pipe

50 mm diaUPVC Pipe

Supplying, laying and jointing CPVC Pipes of approved quality and best variety of pipe of the following dia including labour fixing UPVC Specials, (excluding charges for cutting of pipes, cost of such specials) to wall with necessary teak wood plugs, clamps, screws, UPVC Solution etc., making holes on the walls (or) drilling holes in roof and making good the dismantled portions to original condition with necessray brick work / concrete and plastering wherever necessry with necessary scaffolding charges. complete in all floors complying with standard specification. UPVC pipes shall be got approved by the Executive Engineer before use on works.

Supplying CPVC Specials in water supply arrangements (both in internal and external water supply arrangements

Elbow

Coupling

Union

Supplying and fixing in position first quality and approved Gun Metal Gate valve /wheel valve /check valve (Heavy Type) with ISI mark of the following sizes including cost of shellac,thread etc., Including labour for cutting and threading of GI Pipe etc.,Complete Complying with standard Specfications for both internal & External Water supply arrangements

25 mm dia G.M. Wheel Valve

32mm dia G.M. Wheel Valve

40 mm dia G.M. Gate Valve

50 mm dia G.M. Gate Valve

Supplying and fixing in position 15mm dia following taps (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works)

15mm dia CP Pillar Tap

15mm dia Long body Tap

15mm dia Stop Cock

15mm dia Swan Neck Tap

Supplying and fixing in position 15mm dia two way bibcock(heavy duty) with Health faucet of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 600 x 450 x 5.50mm thick mirror, shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)

Supplying and fixing approved best quality brass CP towel rail 600mm long of approved make with brackets of same materials including cost of teak wood plugs and CP screws, etc.,complete complying with standard specifications.(The tower rail should be got approved by Executive Engineer before use on works).

Supplying and fixing best approved best quality brass CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supplying and fixing coat hook with twin arms heavy tube to rear of wooden shutter of WC cubical,use of S.S screws etc,complete as directed by the dept officers.

Supplying UPVC Specials in water supply arrangements (both in internal and external water supply arrangements

UPVC Elbow

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Tee

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Reducer

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Reducer Elbow

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Reducer Tee

50x40mm dia

40x32mm dia

32x25mm dia

25 x 20 mm dia

UPVC Hex Nipple

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

UPVC Union

50 mm dia

40 mm dia

32mm dia

25 mm dia

20 mm dia

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three sand and Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

75mm dia PVC soil waste pipe

110mm dia PVC soil waste pipe

160mm dia PVC soil waste pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

PVC Elbow

160mm dia

110mm dia

75mm dia

PVC Elbow with Door

110mm dia

75mm dia

PVC Tee

110mm dia

75mm dia

PVC Tee with Single Door

110mm dia

75mm dia

110mm dia

75mm dia

PVC "Y" with Single Door

110mm dia

75mm dia

PVC bend

110mm dia

75mm dia

Supplying and fixing in position PVC cowls of following dia of best approved quality conforming to BIS, etc., complete complying with standard specifications. (The PVC cowl should be got approved by the Executive Engineer before use on works).

75 mm dia

110 mm dia

Construction of Inspection chamber or manhole of the following size including necessary earth work excavation in all soils to full depth as may be directed with sand filling at bottom of the chamber for 10cm thick, concreting CC 1:5:10 using 40 mm guage HBGs jelly 10 cm thick and sode walls 9" thick brick work in cement mortar 1:5 using Fly Ash Bricks of 230 x 110 x 75mm filling the size of foundation with excavated earth, plastering with cm 1:3 20m thick for inside and bottom and making necessary benching with brick jelly cement concrete to the required slope and finishing neatly etc., complete.

Inspection Chamber of Size 0.60 x 0.60 x 0.60m (average depth)

Inspection Chamber of Size 0.60 x 0.60 x 0.90m (average depth)

Inspection Chamber of Size 0.60 x 0.60 x 1.20m (average depth)

Inspection Chamber of Size 0.60 x 0.60 x 1.50m (average depth)

Inspection Chamber of Size 0.60 x 0.60 x 1.80m (average depth)

Supplying and fixing in position of Steel fibre reinforced cement concrete (SFRC)manhole / inspection chamber cover slab with frame size 0.60x0.60m including necessary labour charges for fixing the frame in position over the cement mortar base and finishing the joints etc. complete as directed.

Supplying and fixing of CI steps of approved quality including dismantling masonry wherever necessary and redoing the damaged portion to original condition

Providing PVC Water Bar 150mm wide with singel bulb of approved quality and brand and including fixting etc complete complying with standard specifications and as directed

Providing rain water harvesting pit of 1.50m dia and 1.50m depth with necessary earth work excavation,erecting the five nos of Rcc collar of 1.50m dia,sand filling of 0.60m depth,filling of 40mm HBS Jelly of 0.60m depth and covering with Rcc cover slab of 50mm thick and also connecting 110mm dia PVC pipe of 10.00m legth including transporting charges,fixing,etc.complete.

Drilling bore wells anywhere in Tamilnadu including transportation from one place to another within Tamilnadu in alluvial soil sedimentary strata of clay and sandstone shale pebbles boulders etc, by first taking a pilot bore of 140mm / 150mm dia and then enlarging to required dia and then enlarging to required dia direct or reverse rotary mud circulation method using rotary rigs fuel, labour and drilling bentonite and water required for drillng at site etc complete complying with standard specification and as directed by the departmental officers. Upto 60M Depth.

Reaming 140 / 150 mm dia pilot bore to 300mm dia bore etc complete complying with standard specification and as directed by the departmental officers.Upto 60m depth ending below ground level.

Supplying of PVC casing pipes 160mm assembly (With slot or without slot) in the drilled hole including welding the joints etc., complete supplying and packing the annular space with pebbles of size and quality as approved by the Executive Engineers

Slotted pipe 160 mm Dia

Plain pipe 160mm Dia

Labour charges for inserting PVC casing pipes assembly (with slots or without slots) in the drilled hole including jointing the pipes with PVC Couplers with cement paste etc. complete, cost including supply and packing the annular space with pebbles of size and quality etc complete complying with standard specification and as directed by the dept officers.

Charges for developing the bore well with air compressor of 600 CFM capacity (Minimum 8 Hours) including transportation, labour and fuel charges for compressor etc complete complying with standard specification and as directed by the departmental officers.

Supplying laying and jointing HDPE pipes of 10kg/cm2 for borewell motor purpose of approved quality etc., complete and as directed by the departmental officers.

40mm Dia

25mm Dia

Supplying and fixing of 2 H.P submergible Pump set of approved brand etc complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing of 5.00 HP of approved brand monoblock Pumpwith accessories of starter, Main switch, panel board etc. complete to suit the need (The pump set should be got approved by the Executive Engineer before supply)

REVERSE OSMOSIS PLANT (RO) Supplying and erecting in position of 1000 Litres per Hours capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos.

(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No. Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact

Supply and Fixing of BLUE STAR make Water Dispenor & Coolers with capacity of storage 80 Lts. Nominal cooling capacity 40 liters/hr. Model SDLX 480(pc),Fully stainless steel body with fitted 2 no faucet one for Hot water and one Normal water

Paving the floor with Tactile Paver Type of New Tek BT Yellow Colour Ceramic Tiles of size 305 x 305 x 15mm for Vision Impairment Person laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Supplying and fixing the aluminium anodised fixed glazing partition using 63.50mm x 38.10mm x 1.50 mm @ 0.818 Kg/cm box section for all members and 5.50mm thick plan glass for pnales. The aluminium frames are at 0.60m c/c in both horizontal and vertical directions with necessary triangle shape glazing clips of 19mm x 17.30mm x 0.75 mm @ 0.124 Kg/cm and the rubber beadings for glass pnales including labour charges for fabrication, conveyance, cost of power consumption charges and dismantling, making holes in R.C.C. / masonry wherever necessary with power drill to the required extent and make good to the original condition after fixing the partition as directed by the departmental officers.

Supplying and fabricating and fixing in position powder coated aluminium anodised partly top 1/2 galzed and partly bottom 1/2 panelled door and frame made out of box section 101.6x44.45x3.18mm thick at 2.319 kg\m door shutter made out of box section 47.1x44.45x2.5mm at 1.202 kg\m for vertical style and top, lock rail sections of size 50x44.50x2.5mm @ 1.292 Kg/m and bottom 100.4x44.45x2.50mm at 1.974kg\m using clips of size 17.15x17.27x1.5mm at 0.176 kg\m with necessary metal screws, rubber beading, strike plate type handle of size 100x30x1.60mm at 0.988 kg\m on both sides, tower bolts, lock pivot arrangements and top 1/2 portion with 5.50 mm thick plain glass and bottom 1/2 portion with one side prelaminated board ( MDF ) 12mm thick for panel portion with 1 No. of hydraulic door

closers of approved quality using aluminium extruded section body tubler type universal with double speed adjustment with ISI monogram including cost of furniture fitting such as Pivot, hinges, Tower bolt, lock, door stopper and all materials labour power consumption required for fabrication drilling required for fabrication drilling holes in RCC columns floorslabs masonry wall wherever necessary with power drills to the required extent and make the same to original condition after fixing and as directed. All the aluminium sections are to be anodised with matt finish under electrically controlled condition in accordance with IS 1868-1962 for an average anodic flim thickness of 15 microns etc., complete. The materials should be got approved by the Executive Engineer before use on works. The rate shall be inclusive of all materials, labour for fixing transportation loading, unloading, and all other incidential charges. (Single leaf door)

Providing ornamental decorative columns in the main entrance portico of the building to height of 7.95 mtrs up to Ground floor level with necessary ornamental patterns such as padmam, kodungai, sudhi etc by trained sthapathis as per the approved drawings using cement mortar 1:2 with appropriate bricks used for providing projection wherever necessary etc,using with sscaffoldings. The above work has to be finished neatly without any patches, undulations etc, completed as per the approved drawings and as directed by the departmental offiers etc. The cost includes the cost of all materials, labour, dismantling, redoing, scaffolding , curing wastage etc complete complying with standard specification and as directed by the departmental officers.

Providing ornamental decorative Cornice running pattern in a stepped manner of the following size 400mm,300mm,200mm in the portico roof of the building with vargam, kodi saruku etc by trained sthapathis as per the approved drawings using cement mortar 1:2 with appropriate bricks used for providing projection wherever necessary etc, using with necessary scaffoldings. The above work has to be finished neatly without any patches, undulations etc, completed as per the approved drawings and as directed by the departmental offiers etc. The cost includes the cost of all materials, labour, dismantling, redoing, scaffolding , curing wastage etc complete complying with standard specification and as directed by the departmental officers.

Supply and fixing Shera Board of natural fibres bonded of Cement Board 6mm thick water resistant with necessary painting and Support materials fixed at all levels, complete complying with standard specification and as directed by the departmental officers,The materials should be got approved by the Executive Engineer before use on works.

Supplying and laying red earth, sand and manur mixer as directed by the departmental officer. The proportion of red rod, sand and manure is 1:1:1 and load in layer of 10cm thick in a uniform layer. The cost including cost of all materials, labour for and laying in places as shown by the departmental officer etc complete.

Supplying and laying of korian grass bed over a prepared base including appplication of antitermite chemical like thimpet or purition, neem cake, root regulating fertilizers supply and planing of grass beds cutting the grass to the required or hamental shape etc and carrying out the base management for the turfing for a maintanecne period of three month etc. complete

Supplying and planting Arica Palms as directed by the Engineer in charge including digging holes in ordinary soils and refilling the same with manure, floating with water and dressing removal of rubbish , surplus earth Jif any with all lead and lift also maintenance of plant for a period of 90 days from the date of planting work.

Supplying and planting Specimen edge border Plants as directed by the Engineer in charge including digging holes in ordinary soils and refilling the same with manure, floating with water and dressing removal of rubbish , surplus earth if any with all lead and lift also maintenance of plant for a period of 90 days from the date of planting work.

Supplying and planting Polyalthia longifoliaTree (False Ashoka ) as directed by the Engineer in charge including digging holes in ordinary soils and refilling the same with manure, floating with water and dressing removal of rubbish , surplus earth if any with all lead and lift also maintenance of plant for a period of 90 days from the date of planting work.

Supplying and planting Heliconia Plants as directed by the Engineer in charge including digging holes in ordinary soils and refilling the same with manure, floating with water and dressing removal of rubbish , surplus earth if any with all lead and lift also maintenance of plant for a period of 90 days from the date of planting work.

Supplying and planting Vedicator Plants as directed by the Engineer in charge including digging holes in ordinary soils and refilling the same with manure, floating with water and dressing removal of rubbish , surplus earth if any with all lead and lift also maintenance of plant for a period of 90 days from the date of planting work.

Supplying and planting Azadirachta indica Tree ( NEEM ) as directed by the Engineer in charge including digging holes in ordinary soils and refilling the same with manure, floating with water and dressing removal of rubbish , surplus earth if any with all lead and lift also maintenance of plant for a period of 90 days from the date of planting work.

Providing PPGI Sheet roofing coloured sheet of 0.80mm thick over structural steel fabrication 75x40x3mm MS Tube Rafter and 40x40x3mm MS Tube purlin roof rest on MS Pipe of 100mm dia with Baseplate over the foundation of stub column, the structural members should be welded properly and fixing in position, the cost including necessary fixtures like cleat angle, baseplate, powder coated MS screws, washers and labour charges for fixing and welding, MS members should be painted with one coat of red oxide primer and two coat of enamel paint etc., complete as directed by the departmental officer..

Designing the Semi Unitised Structural Glazing System with open groove joint as per design intent, preparation of shop drawings for approval, supply, fabricate, erect as per approved shop drawings at all floor levels and all floor heights including conducting field test as per the test criteria set out in the particular specification (Metholodgy should be got approved by the Dept. Officials.) Design the framing system (i.e. male & Female frame) to support vision panels, spandrel panels either with glass or aluminium composite panel, openable, window panels on a continuous framing supported between floors. Also design the split framing unutilized glazing system in case of strip or punched windows with vision panel proposed with either insulated / Monolithic glass, groove width in the system both in horizontal and vertical shall not be more than 20mm. Glazing of panel shall be done only at factory at the controlled atmosphere

Design,supply&fixing of Gas outlet points:(Self Sealing type-Single/Dinoutlet type) with S type bracket made up of copper and the out let of non-interchangeable for other gas.The outlet points are brazed with brass bracket with self sealing valve(stainless steel) with all accessories and complete set and are converted by plastic cover duly colour coated as per specific gas and button cover etc.,complete as directed by the departmental officers and as per IS Code 12827/1989 & ISO 7396/1987 specification.

Supply and installation of Medical gas copper pipe line arrangement to hang on the wall of socket type connection installation of seamless cleaned and degreased non arsencial phosphorous gas copper pipe line with saddles complete with brazing work including all copper fitting (Tee,Elbow,Reducer,Coupling).The copper pipe lines should be tested suitable for a steam of working pressure of 17.34kg./cm2(17 bar) and confirm to BS 864 standard with specially made for brazed socket type connection.The medical gas copper pipeline should be tested as per standard and commissioning after painting as per international code no IS 2379/1963 Table-V.The pipe lines installed at the various wings and floors etc.,complete as directed by the departmental officers as per IS code 12827/1989&ISO 7396/1987 specification.

a)42mm dia copper pipe ODx0.9mm thick

b)28mm dia copper pipe ODx0.9mm thick

c)22mm dia copper pipe ODx0.9mm thick

d)15mm dia copper pipe ODx0.9mm thick

e) 10mm dia copper pipe ODx0.9mm thick

Brass Isolation valve. suitable for the copper pipe and should be of non lubricated 90 degree turn lever ball value of RB or Italy or reputed make,connected in line with medical gas pipe line system by using suitable size brass valve adopter union,ferrule,nipple,rubber "O" ring,taption lap and etc.All pipe line regulators shall be capable of controlling pipee line pressure and must compatible with the requirements specified in IS 12827-1989.All valves should be pneumatically tested for twice the working pressure for the gas line as per IS code 12827/1989&ISO 7396/1987 specification.

a)28mm dia ball valve

b)22mm dia ball valve

c)15mm dia ball valve

Oxygen manifold arrangements of 2bankX12 cylinder each wing with Piston type semi automatic control panel which includes contact gauge 2 Nos.,outlet pressure gauge ,brass heavy duty Ioxregulator 2 Nos. with suitable adopter,flexible SS hose.Manifold shall be of a construction and of a designs and matreial suitable for the service pressure in accordance with IS 1282-1989.Emergency alarms with illuminating display for low / high pipe line pressure and malfunctioning of system. 1) Manifold top frame with provision for connecting 3 cylinders on right bank and 3 cylinders on left bank with high pressure interconnecting copper tubing,silver brazing,non return valve,fasteners and cylinder support middle angle frame for claping 2x12 cylinders and related fastenders.The O2 manifold should with stand a pressure of 140kg/CM2.The installation is commissioned after testing as per standards and painted as per international code and as directed by the departmental officers as per IS code 12827/1989 &ISO 7396/1987 specification.

Nitrous Oxide manifold arrangement of 1banksx1 cylinder ,with piston type regulator .1)1x1cylinder Nitrus Oxide manifold should be suitable with stand a pressure pf 140kg/CM2 and above along with high pressure copper annealed tail pipes with end brass adapter suitable for Nitrous Oxide cylinders and manifold.2) Top frame comprising of high pressure copper pipes of size 12mm ID 1.5mm wall thick with high pressure brass fittings made of high tensile brass and connections through non-return valves,high pressure copper tail pipes made of high pressure copper pipe sixe of 7mm IDx1.5mm thick.3)The design of middle and bottom frames should be provided to fit both round and flat bottom cylinders safely with fitted heavy duty regulator.The manifold should be tested at 3500 pig as per IS 12827/1989& ISO 7396/1987 specification.

Supply of Flow meter with humidifier bottle flow meter should be back pressure compressed flow meter should be accurate gas flow measurement with control range 0-13 litres per minute.It should meet strict permission and dumbling standard.The meter body should be made of unbreakable polycarbonate material and auto cleavable at 134 degrees centigrade.The rate includes flow meter and its accessories (Silicon tube with mask).The cost of materials including transport-taxes etc complete as standard as directed by the departmental officers and as per IS 12827/1989 and ISO 7396/1987 specification.

Supply of ward vacuum unit with gauge both mounted on a collection jar of capacity 600ml and with a wall bracket for mounting it on the wall. The collection jar should be made of unbreakable polycarbonate materials which is fully auto cleavable at 134 degrees centigrade as per standard specification and as directed by the departmental officers and as per IS 12827/1989 and ISO 7396/1987 specification.The rate includes cost of silicon hose with SS nipple on either side.

Supply, installation,testing and commissioning of equivalent to ingersoll rand reciprocating Air cooled type (10 HP) rating vaccum pump as per following provisions.As per IS 12827/1987&ISO 7396/1987 specification

Supply,installation,testing,and commissioning of MS fabricated vertical mounted type 1000 liters capacity vacuum receiver tank with inlet and drain holes provided suitable to operate with vacuum pump,etc., as directed by the departmental officers.

Supply, installation,testing and commissioning of compressed air system of reciprocating Anestiwata oil Free Air Compressor belt driven type air compressor with following provisions. As per IS 12827/1987&ISO 7396/1987 specification.

Supply,installation,testing,and commissioning of MS fabricated vertical mounted type 1000 liters capacity Air receiver with inlet and drain holes provided suitable to operate with vacuum pump,etc., as directed by the departmental officers.

Supply, erection, testing and commissioning of Fire Fighting Application Horizontal Centrifugal Type Pump Rated for 2280 LPM at 70 metres head with Electrical Motor of 60 HP of 415 volt 3 phase connection complete with base plate and accessories. (Make: Kirloskar or Equivalent). The rate inclusive of necessary vibration, bad mounting etc., as per standard method as directed by the Deparmental Officers

Supply, installation, testing and commissioning of Diesel Engine Driven Main Fire Pump suitable for automatic operation and consisting of following and complete in all respects as required. a. End suction, top discharge centrifugal pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg. / sq. cm at highest and farthest outlet at specified flow of 2280 LPM at 70m head conforming to IS 1520. b. 68 BHP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant BS & IS standard complete. Auto starting mechanism, 12 volts / 24 volts electric starting equipment like self motor, dyanamo, solenoid switches etc. c. 110 litres capacity diesel tank mounted over stand fabricated using 25mm x 25mm x 6mm size MS angle, providing with level indicator, inlet port, outlet port, drain port and diesel return line port and fuel pre-filter, after filter etc. (Make: Kirloskar / Equivalent).

d. Exhaust system having flexible metallic mufler, 100mm dia MS heavy pipe extended upto 1m, outside pump house duly insulated with 50mm thick glass wool with 1mm thick aluminium sheet cladding, residential silencer with necessory MS support arrangements from wall or ceiling as per site condition.e. Dash board consisting the instruments like temperature gauge, galvano type DC Ammeter, lubricant oil pressure gauge, ignition switch, emergency stop and all other protection equipment as per specification, stop seleneid for auto stop in the event of fault with audio indications, painted with post office red colour etc., as required. f. 12 V / 24 V storage battery, maintenance free tape, 180 AH rating, MS fabricated common base plate, coupling guard, foundation bolts etc., as required. g. Positioning the diesel engine driven fire pump over cement concrete foundation using suitable size anti-vibration mounting arrangement. All works carried out as per standard methods and as instructed by the manufacturer and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply, erection, testing and commissioning Mono Block type Fire Fighting Pressurisation Pump of 180 LPM 110 metres head at 10 HP with suitable base frame including necessary vibration bad mounting etc., including conveying, fixing and incidental charges., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: Kirloskar / Equivalent)

Supply and laying of following sizes of Armoured Aluminium Cables for electrical motor, control panel, pressure switch, jockey motor etc.. The rate inclusive of all incidental charges, neccessary scaffolding and redoing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

3 core 95 sq.mm. armoured aluminium cable

3 core 10 sq.mm. armoured aluminium cable

2 core 1.5 sq.mm armoured multi strand aluminium

Supply and laying of following sizes of Armoured Aluminium / Copper Cables for electrical motor, control panel, pressure switch, jockey motor etc., all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: POLYCAB / PARACON / FINOLEX / EQUIVALENT.

10 core 2.5 sq.mm. armoured aluminium cable

Earthing arrangements with GI Earth Plate including charcoal and salt with necessary excavation in all soils and to full depth as may be required and masonry work, re-filling the sides of foundation with excavated earth as per the standard specification and as directed by the Departmental Officers.

Supply, erection, testing and commissioning of following MS „C‟ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table „E‟, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150mm nominal dia

100mm nominal dia

80mm nominal dia

25mm nominal dia

Wrapping and Coating Anti-Corrosive Treatment for under ground MS pipe having one coat of anti-corrosive metal primer, one layer of asphalt tar tape wound over the MS pipe as per standard methods as per standard specification as directed by the Departmental Officers

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table „E‟, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.

Supply, erection, testing and commissioning of Cast iron body and Gun metal or stainless steel internal Nonreturn valve of following sizes to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers

Supply, erection, testing and commissioning of following sizes of Heavy Duty Foot Valve including all accesories, such as, MS flange of table „E‟, gaskets, bolts & nuts, etc., installed at end of 150 / 200mm dia suction pipe line at sump including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete and as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

150 mm dia

100 mm dia

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT.

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: H-GURU / ISI MAKE / EQUIVALENT

Supply and providing 1000 litres capacity Priming Tank made up of PVC. Make: SINTEX / EQUIVALENT

Priming Tank mounted with the supporting arrangement fabricated using MS angle for the height of 3 metres from the floor level, inlet, outlet, and drain arrangements inside the fire fighting pump room, as directed by the Departmental Officers.

Supply and fixing in position of 12 Volt 180 AH Lead Acid, Sealed Maintenance Free (SMF) batteries with connecting leads, lugs terminal post, etc., as per standard methods and including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of following MS „C‟ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table „E‟, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

100mm nominal dia

80mm nominal dia

25mm nominal dia

Providing, fixing pipe supports from columns / wall or suspenders from roof slab to suit various dia of pipes made out of GI / MS adjustable rods threaded for a sufficient length to adjust the height of support along with clamping arrangement for holding pipes of anchor fastening, arrangement design of hanger and should confirm with specification.100mm

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Gun Metal Gate Valve of size 50mm dia size including necessary MS flange of table „E‟, gaskets, bolts & nuts etc., installed at pump house delivery line for the purpose of priming water to suction line including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: LEADER / EQUIVALENT.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of following MS „C‟ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table „E‟, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

150 mm nominal dia

80 mm nominal dia

Supply, erection, testing and commissioning of cast iron body and bronze internal non-rising spindle sluice valve of sizes at required places to control the flow of water including necessary MS flange of table „E‟, gaskets, bolts & nuts including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: NORMEX / KARTAR / EQUIVALENT

Supply, erection, testing and commissioning of Fire Fighting 4 Way Fire Brigade Inlet with necessary gun metal 63mm dia non return spring shutter arrangements, so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KIARTAR / OMEX / EQUIVALENT

Supply and fixing of stored pressure ABC (Mono Ammonium Phospate) Powder Type Fire Extinguisher of 6 kg. capacity as per IS:15683 with pressure gauge, discharge hose & control nozzle, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc, complete as per standard specification and as directed by the Departmental Officers. Make: EXCELLENT / SAFETY FIRST / EQUIVALENT

Wiring with 2 x 1.5 Sqmm. (22/0.3) PVC insulated SC unsheathed cu. Conductor with of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with 6A Modular switch in flush with Modular MS box and covered with modular plates with suitable colour for PVC concealed light point (5 points per coil)( Crabtree/equ) (DATA-1)

Wiring with 2 x 1.5 Sqmm. (22/0.3) PVC insulated SC unsheathed cu. Conductor with of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with 6A Modular switch in flush with Modular MS box and covered with modular plates with suitable colour for PVC concealed light point (6 points per coil)(Crabtree/equ) (DATA – 2)

Supply and fixing of 20W, 4 feet LED fitting on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting (DATA -3)

Supply and fixing of 20W, 4 feet LED fitting on ceiling with conduit pipe suspension with PVC unsheathed copper leads from terminals to the fittings. (DATA-4)

Supply and fixing of 2x2 42W LED Recess mounted Luminaries fitting (Havells Pluto Make) with conduit /chain suspension and with PVC unsheathed copper leads from terminal to the fitting with necessary connection. (DATA –5)

Supply and fixing of 4’ 20W Twin LED fitting with 1mtr conduit pipe suspension with PVC unsheathed copper leads from terminals to the fitting (DATA –6)

Supply and fixing of 2x2 42W LED surface fitting on wall or ceiling with PVC unsheathed copper leads from terminal to the fitting with necessary connection. (DATA –7)

Supply and fixing of 1x1 18W LED surface fitting on wall or ceiling with PVC unsheathed copper leads from terminal to the fitting with necessary connection. (DATA –8)

Supply and fixing of BH with 10W LED lamp with PVC unsheathed copper leads from terminals to the fitting (DATA-9)

Supply and fixing of WT bulk head fitting with guard (Philips/ Bajaj/ Crompton/ K-Lite) suitable for 9W LED lamp (DATA-10)

Supply and fixing of 1200mm (48”) Sweep AC ceiling fan (Crompton High speed) complete with stepped electronic 300W regulator with 300mm down rod on the existing clamp (DATA –11)

Supply and fixing of 300 mm (12") sweep (light duty) AC exhaust fan complete with necessary wall opening and making good of the wall (SD -114 )

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan (SD-120)

Supply and fixing of AC/DC Call bell suitbale for 230 volts 50 C/s Single phase AC supply on suitable Box with modualr switch. (DATA- 12)

Renewal by Supply and fixing of 48W LED street light fitting with 0.5mtr cowl in the existing post /wall with suitable SMC box with MCB with PVC unsheathed copper leads from terminal to the fitting (DATA –13)

Supply and fixing of 3 modular metal box with suitable Modular front plate with suitable Crab tree Modular switches in flush with wall comprising the following with connection 6/10A One way Module switch crab tree/eq - 1No 6A 5 pin socket crab tree/eq – 1No (DATA-14)

Supply and fixing of 3 modular metal box with suitable Modular front plate with suitable Crab tree Modular switches in flush with wall comprising the following with connection 16A One way Module switch crab tree/eq - 1No 16A 5 pin socket crab tree/eq – 1No (DATA –15 )

Supply and fixing of 12 modular metal box with suitable Modular front plate with suitable Crab tree Modular switches in flush with wall comprising the following with connection 6/10A One way Module switch crab tree/eq - 3Nos 6A 5 pin socket crab tree/eq – 3Nos (DATA –16)

Supply and fixing of 6 modular metal box with suitable Modular front plate with suitable Crab tree Modular switches in flush with wall comprising the following with connection 6/10A One way Module switch crab tree/eq - 1No 6A 5 pin socket crab tree/eq – 1No 16A One way Module switch crab tree/eq - 1No 16A 5 pin socket crab tree/eq – 1No (DATA 17)

Supply and fixing of 18modular Surface box with suitable Modular front plate with suitable Crab tree Modular switches in flush with wall comprising the following with connection 6/10A One way Module switch crab tree/eq - 3Nos 6A 5 pin socket crab tree/eq – 3Nos 16A One way Module switch crab tree/eq - 3Nos 16A 5 pin socket crab tree/eq – 3Nos (DATA –18)

Supply and fixing of 2pole MCB sheet steel enclosure with 25A flush type wall socket with 25A DP MCB for AC plug (Legrand (MDS)/ Hager (L&T) make. (DATA-19)

Supply and fixing of 63A FP MCB in suitable sheet steel enclosure with inter connection.(Make Legrand /Hager Make ) (DATA –20)

Supply and fixing of 12 way SPMCB Distribution board with metal door with IP 42 Protection in flush with wall with 1No 32 Amps DB MCB as incoming and 6 Nos 10Amps SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like Hager make) (Data -21) (SPMCB DB)

Supply and fixing of 7 Segement three phase distribution board with 4 way triple pole MCB distribution board with Metal Door cover with IP42 Protection, with 63A 4 pole MCB as incoming and 3Nos 40A DPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB’s should be with ISI mark. (Like Legrand/Hager L&T make) (DATA -22) (MLDB)

Supply and fixing of Vertical type 4way triple pole neutral MCB distribution board with Metal Door cover with IP42 Protection, with 63A 4 pole MCB Isolator as incoming and 12Nos 6A to 32A SPMCB as Outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager / L &T make) (DATA–23)

Supply and fixing of Vertical type 4way triple pole neutral MCB distribution board with Metal Door cover with IP42 Protection, with 100A 4 pole MCB Isolator as incoming and 12Nos 6A to 32A SPMCB as Outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make) (DATA–24)

Supply and fixing of Vertical type 4way triple pole neutral MCCB distribution board with Metal Acrylic Door cover with IP42 Protection, with 125A 4 pole MCCB as incoming and 4Nos 63A TPMCB as Outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB’s should be with ISI mark.(Like Legrand /Hager L &T make) (DATA –25)

Supply and run of 2 of 1.5 sqmm (22/0.3)PVC insulated SC unsheathed Cu.conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (S.D-55)

Supply and run of 2 of 2.5 sqmm (56/0.3)PVC insulated SC unsheathed Cu.conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (Data-26)

Supply and run of 2 of 4 sqmm (56/0.3)PVC insulated SC unsheathed Cu.conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 57)

Supply and run of 2 of 6 sqmm (84/0.3)PVC insulated SC unsheathed Cu.conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (SD 59)

Supply and run of 4 of 10 Sqmm (140/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour ( DATA-27) ( For 63A Power DB)

Supply and run of 4 of 16 Sqmm (101/0.45) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour(DATA-28) ( for 100A PTPDB)

Supply and run of 4 of 25 Sqmm (168/0.45) PVC insulated SC unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour(DATA-29) ( for 100A PTPDB)

Supply and Erection of 200A capacity dust and vermin proof cubical panel board size of 1800x1500x 600mm ( 5’x5’x2) made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting fuse switch with HRC fuse arrangement in five vertical rows Two for switches with a bus bar chamber and cable chamber and cable alloy confirming to IE rules INCOMER 200A 4 Pole MCCB -1No OUTGOING 1) 125A MCCB - 2No 2) 100A MCCB - 4Nos (All the MCCB's should be Siemens/L&T) The bus bar chamber with consist of 4Nos 1” x 1/4” tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules.

This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel; of earth bus. The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly The panel should be powder coat paint of approved colour approved by the site officer and also the danger board. The capacity of the switches size of incoming and out going cable the place to which the supply is fed should be mounted on switch chamber. The panel board should be mounted on 100mmx 50mmx MS channel provided all around the bottom of the panel. The whole arrangement should be erection of a angle iron frame pedestal to be constructed with suitable foundation bolts and nuts such that the lowest switch handle is at a height of 1.0 m from the ground level and with necessary earth connection (DATA-30)

Supply and Erection of 250Acapacity dust and vermin proof outdoor cubical panel board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting switches with centre bus chamber and vertical covers, cable chamber on both side of the bus bar chamber at the extreme ends on both side and confirming in I.S specifications. INCOMER 250A 4P MCCB -1No OUTGOING 125A TP MCCB -3Nos 100A TP MCCB -4Nos The bus bar chamber with consist of 4Nos 1” x 1/4” tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel of earth bus.

The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly The panel should be powder coat paint of approved colour approved by the site officer and also the danger board. The capacity of the switches size of incoming and out going cable the place to which the supply is fed should be mounted on switch chamber. The panel board should be mounted on 100mmx 50mmx MS channel provided all around the bottom of the panel. The whole arrangement should be erection of a angle iron frame pedestal to be constructed with suitable foundation bolts and nuts such that the lowest switch handle is at a height of 1.0 m from the ground level and with necessary earth connection (DATA-31)

Supply and Erection of 250Acapacity dust and vermin proof outdoor cubical panel board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting switches with centre bus chamber and vertical covers, cable chamber on both side of the bus bar chamber at the extreme ends on both side and confirming in I.S specifications. INCOMER 250A 4P MCCB -1No OUTGOING 100A TP MCCB -9Nos The bus bar chamber with consist of 4Nos 1” x 1/4” tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel of earth bus.

The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly The panel should be powder coat paint of approved colour approved by the site officer and also the danger board. The capacity of the switches size of incoming and out going cable the place to which the supply is fed should be mounted on switch chamber. The panel board should be mounted on 100mmx 50mmx MS channel provided all around the bottom of the panel. The whole arrangement should be erection of a angle iron frame pedestal to be constructed with suitable foundation bolts and nuts such that the lowest switch handle is at a height of 1.0 m from the ground level and with necessary earth connection (DATA-32)

Supply and Erection of 400Acapacity dust and vermin proof cubical panel board made up of 16 SWG CRCA sheet steel with supply and fixing of the following interior mounting switches with centre bus chamber and vertical covers, cable chamber on both side of the bus bar chamber at the extreme ends on both side and confirming in I.S specifications. INCOMER 400A 4P MCCB -1No OUTGOING 250A TP MCCB -3Nos 200A TP MCCB -5Nos The bus bar chamber with consist of 4Nos 2” x 1/4” tinned copper flat for phase and neutral buses on epoxy moulded bus insulated at proper and sufficient spacing between the buses as per IE rules. This bus bar chamber should be segregated from the adjacent chamber by providing hylem sheet of suitable thickness as partisans .2Nos 1/8” tinned copper flats should be provided all round the panel of earth bus.

The fuse switches should be connected with the phase and neutral buses with suitable size of rigid copper flat/rod with suitable lugs phase and neutral tinned buses should be tinned properly The panel should be powder coat paint of approved colour approved by the site officer and also the danger board. The capacity of the switches size of incoming and out going cable the place to which the supply is fed should be mounted on switch chamber. The panel board should be mounted on 100mmx 50mmx MS channel provided all around the bottom of the panel. The whole arrangement should be erection of a angle iron frame pedestal to be constructed with suitable foundation bolts and nuts such that the lowest switch handle is at a height of 1.0 m from the ground level and with necessary earth connection (DATA-33)

Supply and laying of run of 2 of 3 ½x185 sqmm PVC LTUG armoured cable in a trench to be excavated at a depth of 1.0 meter putting 0.15 meter layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (S.D 211 Rs.1351 x 2 =2702) (400A Panel)

Supply and clamping of Run of 2 of 3 ½x185 sqmm PVC armoured LTUG cable on wall with earth connection (S.D229 - Rs.1248 x 2 =2496)

Supply and fixing of brass cable gland for 3 1/2 x 185 sqmm PVC armoured LTUG cable with earth connection (SD 193)

Supply and providing cable end termination of 31/2 X 185 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete (SD 242)

Supply and laying of run of 2 of 3 ½x 240 sqmm PVC LTUG armoured cable in a trench to be excavated at a depth of 1.0 meter putting 0.15 meter layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (S.D 212 Rs.1644 x 2 =3288)

Supply and clamping of Run of 2 of 3 ½x240 sqmm PVC armoured LTUG cable on wall with earth connection (S.D 230 - Rs.1515 x 2 =3030)

Supply and fixing of brass cable gland for 3 1/2 x 240 sqmm PVC armoured LTUG cable with earth connection (SD 194)

Supply and providing cable end termination of 31/2 X 240 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete (DATA-34)

Supply and laying of run of 3 ½x185 sqmm PVC LTUG armoured cable in a trench to be excavated at a depth of 1.0 meter putting 0.15 meter layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (S.D 211)

Supply and clamping of Run of 3 ½x185 sqmm PVC armoured LTUG cable on wall with earth connection (S.D229)

Supply and laying of run of 3 ½x150 sqmm PVC LTUG armoured cable in a trench to be excavated at a depth of 1.0 meter putting 0.15 meter layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good (S.D 210) (250A Panel)

Supply and clamping of 3 1/2 X 150 sqmm PVC armoured LTUG cable on post or on wall with MS clamps (SD 228)

Supply and fixing of brass cable gland for 3 1/2 x 150 sqmm PVC armoured LTUG cable with earth connection (SD 192)

Supply and providing cable end termination of 31/2 X 150 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete (SD 241)

Supply and fixing of brass cable gland for 3 1/2 x 120 sqmm PVC armoured LTUG cable with earth connection (SD 191)

Supply and providing cable end termination of 31/2 X 120 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete (SD 240)

supply and laying of 3 ½ x70 Sqmm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 meter through 50 mm HDPE pipe and refilling the earth to make good (DATA-35)

supply and clamping of 3 ½ x70 Sqmm PVC armoured LTUG cable on post or on wall with MS clamps(S.D 225)

supply and fixing of brass cable gland for 3 ½ x70 Sqmm PVC armoured LTUG cable with earth connection (S.D 189)

supply and providing cable end termination of 3 ½ x 70 Sqmm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc., with electrical connection complete (S.D 238)

Supply and clamping of 3 1/2 X 35 sqmm PVC armoured LTUG cable on post or on wall with MS clamps (SD 223)

Supply and fixing of brass cable gland for 3 1/2 x 35 sqmm PVC armoured LTUG cable with earth connection (SD -187)

Supply and providing cable end termination of 31/2 X 35 Sqmm PVC LTUG Alu.armoured cable with necessary alu.cable sockets by crimping etc with electrical connection complete (SD 236)

supply and fixing of 125A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses Double Break on suitable angle iron frame work with MS cable entry boxes with earth connection(DATA-36)

Supply and fixing of 63A TPN switch disconnector fuses unit in sheet steel enclousure with HRC fuse unit double breake with suitable angle iron frame work with MS cable entry boxes with earth connection only.(DATA-37)

Supply and fixing of special type Fan hook on ceiling ( DATA –38)

Indoor Three Panel Consumer VCB: Supply, erection, testing, commissioning and of 11KV 25KA HT Three panel Vacuum Circuit Breaker Switch, Outdoor type for installation, board comprising one Incomer VCB and 2 Nos Outgoing 630A 500MVA VCB.1.Draw out type 11KV 500MVA 630A Horizontal Draw out/ Horizontal Iso+D108lation VCB operated with spring charged mechanism.Anti Pumping device ,110V DC Shunt Trip and closing Coils (DC source of supply to be derived from a Power pack suitable for 3 Tripping and Two closing operation counter, 4NO + 4NC spare Aux. Contact for customer use,

Automatic safety D109shutter, Mechanical Close/ Trip knob, Mechanical ON/OFF indication, Operating Handle, 110V AC-D109110V DC Power Pack etc. (Incom-1 & Outgoing-2Nos) Core(Core 1-15VA class 1 for metering and core 2-15VA 5P 10 for Protection) Incoming 1 No, Current Transformers of 30/5-5 Amps Dual Core (Core 1-15VA Class 1 for Metering and Core 2-15VA 5P 10 for Protection)(Outgoing-1) 4.Meters: 2. 11KV/Root 3/ 110V/ Root3- Three Phase, 3 Limb 200VA Class 1 Resin Cast Draw out type Potential transformers complete with HT and LT HRC fuses. (Incoming-1 No)

Supply, erection, testing and commissioning of 250 KVA/ 11KV / 433V off load tap changing copper wound Outdoor type distribution transformer conforming to relevant IS 1180 (LEVEL 2) standard and fitted with the following : a) HV side Cable end box for connecting 1R of 120 Sq.mm. HT XLPE Cable. b) LT side cable end box suitable for connecting 4 runs of 3 ½ x 400 sqmm LTUG cable c) Conservator with shut off valve & drain plug valve d) Dehydration silicagel1 breather e) Expansion vent f) 4 Nos. plain rollers g) Thermometer pocket with dial type thermometer with capillary tubing with maximum reading position h) Drain plug / valve with Filter valve i) Oil filling hole, cap & Oil level gauge j) Two body earthing terminals

k) Rating and terminal marketing plate. l) Lifting hooks to facilitate movement of transformer m) OFF load hand operated tap changing switch n) Tap - HV winding voltage variation - 5% to + 5% o) Neutral on LV side to be available for 4 wire supply and brought out through bushing for earthing. p) Air release device q) Transformer to be supplied with first filling of oil. r) All removable covers shall be provided with weather proof hot oil resistant, resistant gaskets to prevent leakage of water into core oil from the tank (Make :CREL/Voltech/equivalent)

Supply and laying of 11KV 3 core 185 sq.mm XLPE HT UG cable in a trench to be excavated at 1.0 Mtr. and covering the cables completely with RCC. Truff and refilling the earth to make good. (DATA-39) (From TNEB RMU to New RMG)

Supply and clamping of 11KV 3 core 185 sq.mm XLPE HT UG cable in Wall or the existing trench in HT Room ) ( Data-40)

Supply and providing cable end termination suitable for 11KV 3 core 185 sq.mm XLPE HTUG cable with necessary indoor type heat / cold shrinkable joint kit and accessories (Make : Ray Chem. / M Seal) (DATA-41)

Design, supply erection testing commissioning and handing over 100KVAR capacity automatic power factor control panel with 100KVAR capacitors with the following specifications L&T etasys-MU contactor switched standard AFC panel/Equivalent capacitors –LTXI ultra heavy duty capacitors. In comer-250A MCCB switching –Auto+ manual 1)Automatic Power factor controller Power factor controller for 100KVAR capacitor bank indigenously designed micro controller based programmable controller works three phase and switching on the suitable capacitor banks and maintaining the PF to the Optimum. The controller is to have a scrolling LCD display which shows instantaneous voltage and current of all the three phases KW, KVA, KVAR and PF indication for the number of banks ON/OFF load in balance and protection for low/High voltage single phasing and phase sequence. 2) Supply and fixing of suitable power supply unit for the power factor controller

3)Supply and fixing of current voltage Transducers of ratio 400:1 to measure current and voltage in all the three phases 4) Supply and fixing of suitable current limiters to cater the inrush current. 5)Supply and fixing of 250A MCCB as incoming to the panel 6)Supply and fixing of suitable MCCB’s for switching ON and OFF of 1 to VIII stage wise capacitors of the capacitor. 7)Supply and fixing of contactors of suitable rating for switching ON & OFF of the capacitors in various stage of L&T make/Equivalent8)Supply and fixing of 150 KVAR capacitor 440V, 50HZ Dleta connected L&T LT/L Ultra heavy duty capacitors Make/ equivalent in 6 Stages in steps. Stage wise details 1)Stage : 12.5KVAR 2)Stage: 12.5KVAR 3)Stage: 25.0 KVAR 4)Stage: 25.0KVAR 5)Stage: 25.0KVAR 6)Stage : 50.0KVAR

Design, Supply, testing and commissioning of 800A floor mounted MV cubical panel bus bar chamber dust and vermin proof accommodating the following switches and 2nos 630A ACB as Incomer units with the following items of work complete to satisfy the latest IS rules and CEIG guidelines. Supply and fixing of suitable size bus bar chamber made up of 16 SWG MS sheet steel with 4 Nos of 2” x ½” tinned copper bus bar for 3 phases and neutral and 2nos of earthing bus of size 1” x 1/8 tinned copper bus on suitable bus bar insulator (Epoxy insulator) with maximum creep age distance and supported on MS base channel frame work of size 4”x2”x 1”-1set incoming 1)Supply and fixing of 2nos 800A ACB and 1No 1600A ACB for Bus coupler,50 KA, Four pole LT ACB (L&T/Siemens) (2Nos. incoming+1No Bus coupler) (setting400A)- 4Pole MDO 50KA cat.No.SL96061 Microprocessor at 600V AC with all accessories for standard

horizontal manual fixed type MCCB equipped with auxiliary contacts and all accessories for closing and opening operation with micro processor relay, over current trip device adjustable to LTD,STD and release for over current protection UV release with time D102delay, Earth fault relay with short circuit protection, Main CT’s for 3 phases lockout, features, separate mould based for each pole for easy maintenance all relevant protection safety access+D99+D97series as per CEIG,IE rules in force with inter connection and terminations as required in specification

2)Supply and fixing 400A TPMCCB ( Make L&T/Siemens) - 3Nos 3)Supply and fixing of 250A TPMCCB (Make L&T/Siemens) - 4Nos Interconnecting the all LT Switches to bus bar with suitable insulated tinned copper flats and painting of phases and neutral indication Double earth connection of the switches to earth bus using suitable tinned copper flats by 2 runs of 1” x 1/8” supply and fixing of LED lamp arrangements with toggle switches to the control to each phase and with rigid connection in suitable separate compartments with 2 sets of supply and fixing of Trivector meter L&T or equivalent make in the cubicle by CEIG rules with supply and fixing of danger board with Siemens grey powder coating with super scribing the names of places to which supply is fed feeder sizes of cables direction of cables etc., Erection of panel board complete with suitable foundation bolts and nuts including suitable MS channel concrete, testing and commisioning.(Data-42)

Earthing as per ISI specification with an earth electrode of 2.1mtr class ‘B” GI pipe of dia not less than 40mm with copper earth plate of size 125mm x 50mmx6mm with necessary funneling arrangement with necessary masonry work with 38 mm RCC cover slab for brick masonry works. (S.D -233.)

Provision of Plate Earthing on with an earth electrode of 2.1mtr class ‘B” GI pipe of dia not less than 40mm with copper earth plate of size 2ft x 2 ft 3mm thickness with necessary funnelling arrangement with necessary masonry work with 38 mm RCC cover slab for brick masonry works. (DATA -43)

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/support on wall / floor/ground for earth connection (SD-76)

Supply and run of 25mm x 6mm tinned copper flat with necessary clamps/support on wall / floor/ground for earth connection (SD-77)

Supply and run of No 8 copper in PVC pipe for earth connection ( DATA-44)

Design, Engineering, Supply, Fabrication, Erection, Testing, Commissioning and Handing over of 1No 26 Persons Bed cum passenger lift ( Gearless with Machine room) as per following technical specifications including all taxes and duties. Technical Specifications: 1. Location: TNIMHANS, IMH,Chennai - 10 2. No of Lift: One No. 3. Type of Lift: bed-cum Passenger 4. Capacity of Lift 26 Persons. (1360Kgs) 5. Speed: 1.00 mtr /Sec 6. Type of Drive: Microprocessor based Specific variable Voltage variable Frequency V3F drive with enhanced ride comfort and near zero leveling functions. 7. No of floor: Ground+ 6 (7floors). 8. Total Travel: 21 Mtrs. (approximate) 9. Leveling Accuracy: High level accuracy with smooth & Jerk free stopping. 10. Construction of car: Special car made of stainless steel finish No.4 hair line finished car panel complete with SS finished fall ceiling ,flooring, lighting fan etc.,

11. Position of Machine: Directly above the lift level. 12.No. of Landing Entrance: One in front 6Nos 13.No. of Car Entrance: One in front only. 14. Landing Entrance Door: (V3F) side opening power operated sliding stain less steel No.4 hair line finished door with full height ultra slim infra red door safety curtain. 15. Lift well : 2500mm(width)x3000mm(depth). 16.Lift pit depth available: 1300mm 17.Car size: 1300mm(width) x2400 mm (depth) X2200mm (height) (as per IS 14665(Part I) – 2000) 18.Car clear Opening: 1200mm widex 2000mm Height (as per IS 14665 (Part-I) – 2000) 19.Lift Machine Room : 3400mm (width)x4400mm(depth) (as per IS 14665 (Part – 5) – 2000) 20.Power Supply: 400/440v, 3 phase, 50 Cy/Sec A.C supply for power and 230 V, 50 Hz single phase AC supply for light.

21.Control: Micro processor Computer based – simplex collective Full collective logic system with/without attendant mode. 22.Car fittings: Compact fluorescent Lighting with 1 No.300mm sweep cabin fan. Lift Well: RCC construction with Brick masonry. 23. Indication: Up/Down Digital Direction scroll type and position indicator for all landing and in car. 24.Emergency Alarm Bell: Battery Operated Alarm Bell to be provided with automatic charging device. 25. Emergency Light: Battery operated Light to be provided with automatic charging device. 26. Fireman’s switch: To be provided at ground floor. 27. Minor Builders Work: To be Provided by lift contractor. 28.Scaffolding: To be provided by lift Contractor. 29.Stainless Steel sill angles and facia Plates: To be provided by lift contractor. 30. Steel for lift Machinery: To be Provided by lift contractor.

31.Servicing and Maintenance: Free Comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year. 32.Provision of intercom with phone: to be provided by lift contractor. 33.Lift License: Preparation of drawing, Payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and lift license as per lift act should be done by lift contractor.34. Automatic rescue device – To facilitate the landing of the nearest floor at the time of power failure This shall consist of suitable type battery system with charges inverter ,under voltage protection system etc. 35. Floor annunciate+C64r with music. 36. Special futures: a) Infra red door sensor with b) Full height screen. c)Full width half height rear panel Mirror. d)Voltage stabilizer for circuit control. e) Tubular Stainless Steel

f)hand rail in car g)signal Fixtures h)Vandal proof S.S. button with S.S. cover i)Stain less steel door frames VF door operator j)Call register signal k)Pit ladder l)Braille buttons m)Stainless steel facia for car operating panel and landing fixtures. n)ON-OFF switch for fan and light o) Over load warning indicator 37 .Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electro magnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angels, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries.

38. Guarantee: Guarantee for the Materials& workmanship of equipments complete should be offered by the Lift firm for a period of not less than one year. 39. Site testing in accordance with IS 14665 should be carried out at the+C58 time of handing over. C65

Design, Supply Installation, testing and commissioning of 8.5 TRnominal capacity ceiling suspended Ductable Air conditioner with theFollowing components.a)8.5TR capacity ceiling suspended Ductable Air Conditioner high tech,low height, low noise level indoor unitwith fin and tube type cooling coil,Detachable type drier provided inrefrigerant circuit to reduce moisture content multi stage type distributorfor feeding equal quantities of the Refrigerant mixture to all the section ofthe coil, with required valves,directlycoupled blower to reduce troubles andwear & tear compared to belt driveBlower. Thermostatic expansion valve arrangement, lift and pull type aluminium framed durable, washable air filter, Integrated electrical panel with complete microprocessor control with display for easy operation and maintenance of unit common operating conditions of 45 F suction temperature Auto reset type HP/LP safety cut sensor type to improve Reliability of compressor. Type QTY- Ceiling Suspended Blower QTY – 2 Nos Motor Power – 415V /3Ph/50HZ Air flow -4400 CFM

B)8.5 TR capacity suitable for ceiling suspended Ductable Air conditioner high tech Outdoor unit with power saving high efficiency sturdy and rugged 1 No of scroll compressor each with inbuilt internal thermal protector, internal pressure relief valve, Auto reset type HP/LP safety cut sensor out to improve reliability of compressor andcondenser shall be made of super slithigh efficient aluminium fins mechanically bonded to copper tubescondenser ‘L’ type coil to berigidlyfixed to unit frame with fastenersimported condenser fan & fan bladesto be statically and dynamicallybalanced to reduce noise andVibration. The fans are direct driven3phase motor with protection.Condensing temperature 130’f for thesystem operations. Refrigerant Compressor – Scroll No of Compressor – 1No Refrigerant – R22 Power supply – 415V/3Ph/50HZ No of Fan – 1Nos Types of Mounting – Rubber mounts with sleeve

DX AIR COOLED CONDENSING UNITS Design, Supply, Installation, testing and commissioning of DX Air-cooled Condensing Unit fixed with energy efficient scroll compressor along with grooved copper tube/aluminium fins air cooled condenser coil with anticorrosion coatings, liquid accumulator, low noise aluminium propeller condenser fan with IP 55 motor etc. all suitably assembled neatly in heavy duty GSS sheet metal cabinet and duly powder coated as per specification. The Unit to include built-in safety controls like HP/LP switch power quality protector, in-built thermal/temperature protection.

Supply, Installation, Testing and commissioning of factory built floor mounted / ceiling suspended 8.5 TR capacity DX double skin type horizontal air handling units made of 25 mm thick panels consisting of pre plasticized G.I. casing of thickness 0.8mm outside layer and 0.8mm inside layer with polyurethane foam (PUF) insulation factory injected between them by injection moulding machine, complete with blower section with blower suitable for static pressure as required, cooling coil section with aluminium finned copper tubes (tubes thickness not less than 0.5 mm) cooling coil of 6 row deep, filter section with 50 mm thick metal viscous/ washable synthetic type air prefilters, belt drive package with TEFC drive motor of efficiency class IE3 suitable for 415 ± 10% V, 50Hz, 3 Phase AC supply suitably designed for variable frequency drive application, drain connections, stainless steel (18G) drain pan with PUF insulation, vibration isolation arrangement etc. complete as per specification .

Supply, installation, testing and commissioning of supplied AHU connection DX kit comprising electronic expansion valve and control panel.

Supply and filling of R-22 Refrigerant Gas.

Supply & fixing of hard drawn copper Refrigerant piping of suction line of Size 1 1/8” inches with necessary fitting and clamp etc.

Supply & fixing of hard drawn copper Refrigerant piping of liquid line of size 5/8” inches with necessary fitting and clamp etc...

Supply and fixing of flexible canvas connection between indoor unit and ducting and rubber pads, with ceiling Support angle rods etc.

Supply and fixing of suitable MS angle frame if required necessary Base frame for mounting the outdoor units for protection from the rain water with dust flow on the open trace / corridor Floor area

Supply, Fabrication and Installation of Aluminium Ducting arrangement with necessary angle supports, anchor fasteners and threaded rods etc. as required

Supply, Fabrication and Installation of GI ducting Ducting arrangement with necessary angle supports, anchor fasteners and threaded rods etc. as required

Supply and Providing Thermal Insulation of 9mm thick –XLPE with aluminium foil./ Nitrile Rubber insulation

Supply and providing acoustic lining for initial portion of ducting with 10mm thick XLPE insulation.

Supply, fabrication and fixing of Volume control dampers individually across the duct

Supply and fixing of powder coated Extruded aluminium supply air grilles/diffuser with MS volume control damper for supply.

Supply and fixing of 1 inch PVC water drain pipe line on wall with suitable Clamp as required.

Towards charges for welding, leak testing, Nitrogen pressure testing, pressure holding, vaccummising, dehydration and other related works etc.

Supply, fabrication and fixing of suitable angle support frame for ceiling mounted the Indoor Units.

Supply and providing of pipeline nitral rubber insulation for section line Refrigerant pipe as required.

Supply & providing of Power supply for MCB to Outdoor unit with 4 core 10 sq.mm copper flexible cable

Supply & providing of control supply for Outdoor unit to Indoor unit HP and LP cut-outs with 7 core 1.5sq.mm copper flexible cable

Supply and fixing of 8" dia Flexible duct with insulation.

Supply and fixing of Butterfly damper for control the CFM

Supply and fixing of microvee filter 600x600mm size fine microwave mesh filter with efficiency of 5 micron level for return air.

Supply, fabrication and fixing of Fresh air Louver

Supply, installation, testing and commissioning of Laminar flow HEPA filter Modular Housing of size 8' x 6' x 1.5' ht. for ceiling suspension above the Operating Table in OT. The Housing shall be of extruded aluminium frame and insulated panels with 40 mm thick PUF and thermal break arrangement similar to AHU Housing. Complete as per specification.

Supply and Fixing of 7.5-10 HP Star delta starter in Sheet-Steel Enclosure Type MN / ML(Motor Rating AC-3 Duty, 415V, 50Hz, 3-Ph) with suitable necessary connections.

Supply ,Erection,Testing and commissioning of 2.0TR split type Air conditioner with one outdoor air cooled condensing unit and indoor evaporator with inter connection of copper refrigerant piping between condensing unit and evaporator unit electrical cabling of performing cooling ,dehumidifying air circulating filtering etc.. suitable for operation on 230V 50Hz single phase

Supply and fixing of 5KVA wall mounting type Automatic voltage stabilizer with time delay arrangements suitable for operation at 230 Volt, 50 Hz, AC power supply (Make: V –Guard)/ Equivalent.

Supply and Installation of Extra copper pipe with necessary insulation, Cabling & Drain arrangement etc…

Supply and fixing of angle iron stand for outdoor Unit

Supply and Installation of copper 18 mm Copper Rod size of 8 feet length buried in earth including excavation of earth upto the depth of 8 feet and closing the pit. Fill with bentonite 25 kgs chemical and including PVC pit cover.

Supply and Installation of copper air terminal spike arrestor with base and all fittings.

Supply and installation of 70Sqmm Copper Cable run on the external wall from terrace to the ground floor in PVC 1" Conduit.

Supply and insallation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp (S.R)

Supply and Installation of 1000 Devices Addressable Wireless Fire Alarm Panel with LCD display for type of alarm, zone and time of activation, large LCD display. History of upto 100 logs can be stored. Battery backup and inbuilt charger available for 12 V 7 AH batteries. All wireless zones should be able to arm/disarm from the panel. Normal open/close PFC output shall be available. Shall operate on 230 VAC single-phase supply.

Supply and installation of Wireless addressable smoke detector photoelectric type with base and led to operate on 9 v dc supply.

Supply and installation of addressable electronic sounders 5 watts with inbuilt Transmitter, wall mounting type to operate on 230 V AC supply.

Supply and Installation of wireless manual call points press type.

Supply and installation of wireless signal transmitter repeater wall mounted for wireless smoke detector and panel connectivity.

Supply & wiring of CAT 6 copper cable in pvc conduit with all fitings.

GST at 18%

N S Periasamy and Co

PRIYA ENGINEERING PROJECTS PRIVATE LIMITED