REPAIRS, REPLACEMENT OF TILING , PLASTERING, PLUMBING, JOINERY AND ALLIED WORKS TO KV SCHOOL, KG SCHOOL, DAD HOSTEL AND AGE OFFICE UNDER AGE BR-II OF GE (I) RndD (WEST) BANGALORE

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for; and disposing of debris outside MD land complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level) and disposing of debris outside MD land complete all as specified and as directed.

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for; including reinforcement cut as required to facilitate demolition, and disposing of debris outside MD land complete all as specified and as directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and disposing of debris outside MD land complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles to store and rubbish off the premises and disposing of debris outside MD land complete all as specified and as directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water, etc., and disposing of debris outside MD land complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) area of opening not exceeding 1.5 sq m each all as specified and as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frames) area of opening exceeding 1.5 sq m, but not exceeding 4 sq m each all as specified and as directed.

Taking down shutters of any description of area not exceeding 1 sq m, complete all as specified and as directed.

Taking down shutters of any description of area exceeding 1 sq m and not exceeding 2 Sq m each complete all as specified and as directed.

Uprooting, scrubbing out shrubs / plant / flora / fauna on walls, girth not exceeding 100 mm, cutting holes in walls, digging out roots applying (No Suggestions) acid / phenolic acid as per manufacturers instructions to burn out deep grown roots and making good the surface using CM 1:3 (mixed with and including water proofing compound) complete all as specified and as directed. (Note : The height of walls is up to 16 m, necessary cost of scaffolding shall deemed to be included in quoted rate.)

Material and labour for Plain Cement Concrete (1:3:6) type C0, using 12.5 mm graded stone aggregate as in filling the Chowkats/frames complete all as specified and as directed.

Supply only liquid water proofing compound all as specified and as directed.

Material and labour for, Pre-cast Reinforced Cement Concrete, (1:2:4), type B1 using 20 mm graded stone aggregates as in cover slabs of manholes, gully traps, drains, etc., set in CM(1:4) complete all as specified and as directed. NOTE :- Steel for Reinforcement will be measured and paid separately.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exceeding 10 cm girth, all as specified and as directed.

Material and labour for Plain Cement Concrete (1:5:10) type E2, using 40 mm graded stone aggregate as in sunken slab filling, mass concrete etc, complete all as specified and as directed.

Material and labour for Plain Cement Concrete, (1:2:4), type B1, using 20 mm graded stone aggregates as in padding concrete, leveling course and like, (including mixing with water proofing liquid as per manufacturers instructions), obtaining uniform slope on roof top and finishing the surfaces to received further treatment complete all as specified and as directed. Note : Supply only liquid based water proofing compound will be measured and paid for separately under respective item.

Material and labour for Pre-cast cement concrete block masonry with grade ‘C’ solid blocks exceeding 10 cm in width, having minimum compressive strength of 50 Kg / Sq cm as per IS 2185 (Part- I) 2005 and set in CM 1:6 complete all as specified and as directed.

Material and labour, steel reinforcement using TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending and binding with mild steel wire (annealed) and not less than 0.9 mm dia complete all as specified and as directed.

Supply and fix, Pressed steel door frame of size 105 x 60 mm using 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and as directed.

Supply and fix, 30 mm thick Factory made solid panel PVC door shutter consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat molded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete including Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, including making good to jambs with cement mortar (1:4) and finished to match with existing surface complete all as specified and as directed.

Supply and fix, 35 mm thick Factory made Second class hardwood Glazed, gauged and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to Chowkats all as specified and as directed.

Supply and fix 35 mm thick plain framed paneled factory made shutters (two panel) with II nd class hardwood rail and style with lock rail and panel of 12 mm BWP commercial ply with commercial veneer on both faces. The size of rail and style as per IS - 1003 Part - I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supply and fix 25 mm thick, Factory made flush door shutters, 25 mm thick, solid core construction, with block board core panels and plywood face panels, commercial type on both sides, complete all as specified and as directed.

Taking down unserviceable boards as in shelves of cupboards, doors, etc., supply and fix 18/19 mm thick one side pre-laminated particle board, interior grade, with decorative choice lamination on other side, fixed with screws, including providing 6 mm thick teak wood edging etc., complete all as specified and as directed.

Re-securing or easing or adjusting wooden door shutters of any description (without taking off shutter from frame), of area exceeding 1 sq m but not exceeding 2 sq m each, including making good the disturbed surfaces to match the existing, complete all as specified and as directed.

Repairs to steel window / ventilator shutters of (area not exceeding 0.60 Sq m) any description, including replacing handles, steel hinges of any pattern, peg stay etc., and making window / ventilator absolutely working condition, including necessary welding, complete all as specified and as directed.

Supply and fix, Stainless steel Butt hinges, 100 mm long fixed with screws complete all as specified and as directed.

Supply and fix Continuous (piano) hinges, mild steel, bright finish or electro-galvanized, width of flap when opened shall be not less than 30 mm, complete all as specified and as directed.

Supply and fix Aluminium anodized barrel tower bolts of extruded section, 150 mm long all as specified and as directed.

Supply and fix 150 mm Aluminium extruded alloy anodized handles, cast type complete all as specified and as directed.

Supply and fix, 300 mm long Aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fix, stainless steel wire cloth 0.36 mm nominal dia of wire, and of average width of aperture 1.4 mm, fixed with stainless steel wire staples / wooden beading complete all as specified and as directed.

Supply and fix in repairs stainless steel wire cloth 0.36 mm nominal dia of wire, and of average width of aperture 1.4 mm, fixed with stainless steel wire staples / wooden beading complete all as specified and as directed.

Supply and fix in repairs , Floor door stopper, 150 mm length of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Supply and fix in repairs, chromium plated , peg set (Set of 6), fancy type, (as approved by GE), fixed with screws, complete all as specified and as directed.

Supply and fix powder Coated aluminium frames and shutters (minimum thickness of powder coating 50 microns) and fabricating of doors, windows, ventilators and fixed partitions with one or more rebates including necessary joining cleat, glazing clips, rubber packing, snap bending crews etc. complete all as specified and as directed. Note :- i) For payment purpose weight of aluminium section shall be measured and paid, ii) Cost of aluminium mongery. lock, rubber packing, rollers for sliding shall be deemed to include in the quoted rate, iii) Sheet glass and wire gauge shall be measured and paid for separately under respective items.

Supply and fix, mild steel work as in framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Taking down unserviceable steel windows / ventilators or aluminium windows or ventilators with frame without taking of shutter (double leaf/triple leaf shutter with frame i.e. fly proof and glazed) from the frame not exceeding 0.5 Sq m each except grill, including glass panes, mosquito proof mesh complete all as specified and as directed.

Taking down unserviceable steel windows / aluminium windows with frame without taking of shutter (double leaf/triple leaf shutter with frame i.e. fly proof and glazed) from the frame exceeding 0.5 Sq m each and not exceeding 3 sq m each except grill, including glass panes, mosquito proof mesh complete all as specified and as directed.

Material and labour, 25 mm thick, Plain Cement Concrete 1:2:4, type B0, using 12.5 mm graded stone aggregates as in flooring, complete all as specified and as directed.

Material and labour, for 75 mm thick Plain Cement Concrete (1:3:6), type C1, using 20 mm graded stone aggregates as in paving / plinth protection, laid in panels, finishing the surfaces even and fair complete all as specified and as directed.

Material and labour, for 75 mm thick Plain Cement Concrete (1:4:8), type D2, using 40 mm graded stone aggregates as in sub base of flooring, etc., finishing the surfaces even and rough complete all as specified and as directed.

Material and labour, non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIa), area of each tile exceeding 0.06 sq m but not exceeding 0.11 sq m, as in flooring, set and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour, Joint free non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIA), area of each tile exceeding 0.18 sq m but not exceeding 0.38 , as in flooring, set and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Material and labour, Joint free non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIA), area of each tile exceeding 0.18 but not exceeding 0.38 , as in vertical surfaces such as skirting / dado etc., , set and pointed in white or coloured cement to match colour of tiles over and including 10 mm thick screed bed in CM (1:3) complete all as specified and as directed.

Material and labour, for Glazed ceramic coloured tiles, of size 450 x 300 x 7-8 mm thick (Grade B-IIa) as in vertical surfaces such as skirting, dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, laid over and including provision of backing coat of 10 mm thick in CM 1:3, complete all as specified and as directed.

Renewing glazed ceramic tiles in patches area not exc.5 sq m, preparing the beds and laying of new tiles setting jointing, pointing etc and matching with the existing surfaces, over and including 10 mm thick backing coat in CM 1:3, complete all as specified and as directed.

Demolition of stone slabs of any thickness and in any position, providing material and labour, for 18 to 20 mm thick Granite work (of any type), table rubbed and mirror polished), in single piece in steps, jambs, pillars, window-cills, cooking platform and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, making hole for gas pipe, edges made half round, laid over and including screed bed or bedding layer of 15 mm thick in CM (1:4), complete all as specified and as directed.

Demolition of stone slabs of any thickness and in any position, providing material and labour, plain cement chequered concrete tiles 30 cm x 30 cm x 20-22 mm thick, with pigments, set, jointed and pointed in neat cement slurry in floor including 15 mm thick screed bed in cement mortar 1:4 with grey cement and pigments complete all as specified and as directed..

Grinding and polishing to existing terrazzo/ kota stone flooring, complete all as specified and as directed.

Material and labour, for rendering 10 mm thick in Cement mortar 1:6, on brick work/concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed

Material and labour, for rendering 15 mm thick on walls of brick / stone / concrete surfaces in two layers (base layer 10 mm and finishing layer of 5 mm thick in CM 1:4, including mixing water proofing compound and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed. Note : Supply only water proofing compound will be measured and paid for separately under respective item.

Material and labour, for rendering 5 mm thick on brick or concrete ceiling surfaces in cement mortar(1:3) and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Material and labour for, rendering 15 mm thick in cement mortar 1:3 on concrete surfaces, finishing even and smooth including mixing with water proofing compound and applying 1 mm thick Brush Bond, RFX Grey of FOSROC or techno-commercially equivalent as per user’s manufacturer’s instructions, complete all as specified and as directed. Note:- Supply only water proofing compound will be measured and paid for separately under respective items.

Preparation of new or previously untreated plastered wall surfaces of any description not otherwise described and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1 mm thick wall care putty, complete all as specified and as directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Preparation of new or previously untreated plastered ceiling surfaces of any description not otherwise described and applying two coats of oil bound distemper over a coat of alkali resistant primer over and including 1 mm thick wall care putty, complete all as specified and as directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gram/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 over and including priming coat of exterior primer applied @ 0.90 litre/ 10 over new surfaces

Material and labour for, Preparation of old plastered and applying one coat of oil bound distemper on wall surfaces complete all as specified and as directed.

Material and labour for, Preparation of old plastered and applying one coat of oil bound distemper on ceiling surfaces complete all as specified and as directed.

Preparing of old wall concrete surfaces, and providing material & Labour for applying one coat of 100% Premium acrylic emulsion paint having VOC less than 50 gram/litre and UV Resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 complete all as specified and as directed.

Complete removal of existing treatment and preparing the surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer over 1 mm thick wall care putty complete all as specified and directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Complete removal of existing treatment and preparing the surfaces of ceiling and applying two coats of oil bound distemper over a coat of alkali resistant primer over 1 mm thick wall care putty complete all as specified and directed. Note : Quoted rate shall deemed to include for cost of wall care putty.

Hacking out old broken glass of any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/ spring clips, complete all as specified and as directed.

Supply and fix Plain Sheet glass 4 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane all as specified and as directed.

Supply and fix Figured glass, 4 mm thick, pin head type and glazing with oil putty in squares not exceeding 0.5 sq m in each pane all as specified and as directed.

Preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth applying one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of new steel surfaces exceeding 10 cm in width or girth, applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Preparation of new wooden surfaces exceeding 10 cm in width or girth, applying two coats of synthetic enamel paint over a coat of red oxide pink primer complete all as specified and as directed.

Taking down unserviceable GI tubing, supply and fixing new 15 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Taps, valves in any shall be removed before taking down pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Taking down unserviceable GI tubing, supply and fixing new 20 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Taps, valves in any shall be removed before taking down pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Supply and fix Bib taps 15 mm dia, fancy type, chromium plated with CP flange all as per Cat No. HT F3001151 of Cera or equivalent in other makes specified complete after taking down old bib taps all as specified and as directed.

Supply and fix two way, bib taps, fancy type, 15 mm dia, cast copper alloy, chromium plated, with CP flange, screwed for iron pipe or for brass ferrule, all as per Cat No.HT F3001163 of Cera or equivalent in other makes specified complete after taking down old bib taps all as specified and as directed.

Supply and fix Pillar taps, 15 mm dia, fancy type, chromium plated with CP flange, long shank all as per Cat No. F3002101 of Cera or equivalent in other makes specified here-in-after, after taking down old pillar taps complete all as specified and as directed.

Supply and fix in repairs, Stop valves (concealed), fancy type with CP wall flanges, chromium plated, cast copper alloy with long shank and exposed part kit with fittings sleeve, operating lever concealed part screwed both ends for iron pipe or for unions, including making good the disturbed portion matching with adjacent surfaces, complete all as per Cat No.HT F4050103 & HT F3001351 of Cera or equivalent in other makes specified here-in-after, complete all as specified and as directed.

Supply and fix in repairs, Angular stop cock, fancy type, with chromium plated wall flange, cast copper alloy, screwed both ends for iron pipe or for brass ferrule,15mm dia, complete all as specified and as directed. MAKE:- Cat No. HT F3001201 of CERA or techno-commercially equivalent model in any one of the make as mentioned in list of makes here-in-after.

Supply and fix in repairs, Chromium Plated overhead shower rose of size 95 mm with swivel joints, over head shower arm of 230 mm long with wall flange, complete all as specified and as directed. Make : Cera Cat Part No F7020305 & F7040103 or techno and commercial equivalent in other makes specified after taking down old shower rose complete all as specified and as directed.

Supply and fix in repairs, brass chromium plated, fancy type, soap dish, as per Cera Cat Part No F5003106 or equivalent in other makes, and fixing with brass screws, complete all as specified and directed.

Supply and fix in repairs, stainless steel toilet paper holder with flap guard, fixed to wall with CP brass screws and PVC cleat complete all as specified and as directed. Make: Cat Part No F5002110 of Cera or techno commercial equivalent in other makes, complete all as specified and as directed.

Supply and fix in repairs hand shower for Health faucet, 8 mm dia, 1.2 m long, flexible tube in chrome finish, wall hook with NRV (back flow preventer), all as per Cat Part No ALD-577 of Jaquar or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs, single tube towel rail, brass chromium plated, 600 mm long fixed with chromium plated screws and PVC cleats, complete all as specified and as directed. Make : CERA, Model No F5003103 or techno and commercial equivalent complete all as specified and as directed.

Supply and fix in repairs, single tube towel ring, 200 mm dia, brass chromium plated, fixed with chromium plated screws and PVC cleats, complete all as specified and as directed. Make : CERA, Model No F5004105 or techno and commercial equivalent complete all as specified and as directed.

Supply and fix in repairs, gun metal, globe or gate valves 20 mm bore with iron wheel head screwed both ends for iron pipe including necessary cutting/threading the old pipe and provision of new fittings such as Tee, socket, elbow, union if required complete all as specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, water closet pan (pedestal pattern), with PP soft seat cover, hinges, other fixing accessories set (excluding flushing cistern and flush pipe), UPVC (SWR), 'P' or 'S' trap, and connecting to drain (or outgoing pipe), flush pipe, anti syphonic pipes, Make : Cat Part No S1050101 of Cera or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, 'Orissa pattern' squatting pan of size 580 mm x 440 mm with UPVC 'P' trap or 'S" Trap, front or back inlet, integral foot rests, connecting to trap, flushing pipe, anti syphonic pipe, complete, all as per Make : Cera, Cat No S3010102 of CALINA make or techno commercially equivalent in other makes specified complete all as specified and directed.

Supply and fix in repairs, PVC valve less, syphonic action type, white colour flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including jointing with new PVC long / short flush bend and making good to the disturbed surfaces complete all as per Model No: CIENA PREMIUM Cat Part No B1010102 of CERA Make or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix in repairs, Vitreous china snow white, wash hand basin (without pedestal) of size 550 mm x 400 mm all as per Cat No. No. S2040103 of Cera or techno and commercial equivalent makes specified including 32 mm dia PVC waste pipe of minimum 800 mm long with PTMT waste coupling 32 mm dia, all as specified and as directed.

Supply and fix in repairs, Vitreous China urinals, bowl type (back or corner wall type), of size 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe), complete all as specified and as directed.

Taking down old sinks and Supply and fixing Stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen over all size 915 mm x 460 mm with bowl size 405 x 355 x 178 mm all as per Cat No.SSSBSD-52 of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 40 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc. complete all as specified and as directed.

Taking down unserviceable plate rack, supply and fix new Stainless steel plate rack of size 600 mm x 750 mm and fixed with CP screws and PVC cleats complete all as specified and as directed. Make: Blue star, Model No. SSKPR-311.or techno-commercially equivalent make of NIRALI / ANJALI / JAYNA / DIAMOND.

Dismantling of water tanks of 500 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 500 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Dismantling of water tanks of 1000 litres capacity from roof top and supply and fixing Rotational moulded polyethylene water storage tanks (triple layered) of 1000 Litres capacity with ISI mark embossed on it, (cylindrical, vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

Supply and fix in repairs Ball valves of 20 mm dia , (minimum weight 210 grams) , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed.

Supply and fix in repairs, Push tap any colour high pressure of PTMT screwed for iron pipe and fixed, (Minimum weight 15mm-47gms/ 20mm- 75gms) complete all as specified and as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, UPVC (SWR) pipes 110 mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, UPVC (SWR) pipes 75 mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed.

Supply and fix, PVC connecting pipe 600 mm long 15 mm dia both ends having brass coupling nut and PVC washer after taking down old connecting pipe complete all as specified and as directed.

Dismantling of unserviceable floor / nahani trap, supply and fix PVC(SWR) floor / nahani trap 75 mm dia outlet with CP grating, including jointing with solvent cement complete all as specified and as directed.

Dismantling of unserviceable multi floor trap, supply and fix PVC(SWR) multi floor trap 75 mm dia outlet with CP grating, including jointing with solvent cement complete all as specified and as directed.

Supply and fix in repairs, PVC (SWR) bends any radius 75 mm dia without access door, fixed in pipes, complete all as specified and as directed.

Supply and fix in repairs, UPVC (SWR) vent cowl of bore 110 mm dia, complete all as specified and as directed.

M/s SRINIVASA CONSTRUCTION COMPANY

Sai Ram Builders

S CHANDRASHEKAR (SREE BUILDERS)

RASHMI BUILDERS

Lucky Enterprises