PROVN OF RETAINING WALL, PROVN OF AREA DRAINAGE AND CATTLE FENCE AND OTHER SANCTIONED WORKS IN THE AREA OF AGE B/R-II UNDER GE PANAGARH

Amount

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in soil complete all as specified and directed.

M&L for hardcore of stone or boulders of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed

M&L for 100 mm thick cement concrete type D-2, 1:4:8 (using 40mm graded stone aggregate) As in sub base complete all as specified and directed.

M&L for Excavation in trenches n exc 1.5m wide and nexc 1.5m depth for foundation etc or for shaft ,well cessipts, man hole ,pier hole etc n-exc 10 sqm on plan and n exc 1.5m depth and getting out soft/lose soil complete all as specified and directed

M&L for removing excavated soil n.exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed

M&L for returning ,filling including spreding,levelling watering and well raming in layer n exc 25 cm complete all as specified and directed

M&L for brickwork with old size fly ash bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6) complete all as specified and directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), using water proofing compound complete all as specified and directed. ) (Note : WPC will be measured and paid seperately.

Excavation in post holes not exc 0.50 cum, getting out, returning filling in and ramming earth, watering and removing surplus soil not exc 50 m in soft/loose soil complete all as specified and directed

M&L for steel work in tubular trusses Post/columns including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade ST-240, complete all as specified and directed.

M&L for chequred cement tiles 250X250X22mm /300X300x25mm thick set and jointed and pointed in neat cement slurry with gray cement and pigment and over 15 mm thick screed bed in cement mortor 1:6 complte all as specified.

M&L for pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed.

M&L for preparation surfaces of steel over 10 cm width or girth and apply of two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and blinded with earth and rammed incl watering complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed

M/L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade mixed with grey cement and pigments complete all as specified and directed

M&L for 15mm thick in cement mortar (1:4) rendering on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

M&L for cement concrete type D2 1:4:8 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L for use and waste of formwork to sides of footing and plinth beams finished fair and rough complete all as specified and directed.

All as per item No 22.00 mentioned here-in-above but for coloums complete all as specified and directed

All as per item No 22.00 mentioned here-in-above but for chajjas complete all as specified and directed.

All as per item No 22.00 mentioned here-in-above but for sides and sofits of beams and lintels complete all as specified and directed.

All as per item No 22.00 mentioned here-in-above but for sofits of slab complete all as specified and directed.

All as per item No 22.00 mentioned here-in-above but for walls, retaining walls, abutments, parapets and staircase railing and similar work including attached pillasters ,buttresses etc vertical or batter complete all as specified and directed.

All as per item No 22.00 mentioned here-in-above but for side of slab exc 10cm but n.exc 20cm thick complete all as specified and directed.

M&L for cement concrete type C2 1:3:6 (using 40mm graded stone aggregate) 75mm thick as in plinth protection finished even and smooth with out using extra cement complete all as specified and directed

M&L for brick work with fly ash bricks old size, straight or curved on plan to any radius,in half brick walls built in cement mortar (1:4) complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 31.00 mentioned here-in-above but 6mm to 8mm dia complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6), complete all as specified and directed.

M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar (1:3) complete all as specified and directed.

M&L for prepartion of newly plastered wall surfaces and applying three coat of white wash complete all as specified and directed.

M&L for prepartion of newly plastered ceiling surfaces and applying three coat of white wash complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as specified and directed.

S&F Factory made steel ventilator with centre hung shutters, dovetailed or welded including pintol hinges, steel handles, etc. as shown with fixed type including one shop coat of red oxide zinc chrome primer complete all as specified and directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel complete all as specified and directed

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed

S&F 150 mm long aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

M&L for glazed ceramic colour joint free tiles tiles in verticle surface 350x250x7mm thick set and jointed in neat cement slurry over 10 mm thick (1:3) cement mortar plaster and pointed in coloured cement to match complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors laid over 15mm thick 1:4 cement mortar screed bed etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match complete all as specified and directed.

M&L for cement concrete type B0 (1:2:4) (using 12.5 mm graded stone aggregate) 25 mm thick as in floor for receiving screed bed of floor tiling complete all as specified and directed.

M & L 3mm thick figured glass, pin headed type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F Stop valves 15mm dia CP fency type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

M&L for steel tubes,15mm dia bore 'medium grade' with all fitting; laid in trenches or wall complete all as specified and directed.

M&L for PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement etc complete all as specified and directed

S&F vitreous China wash basin white, flat back,size 580X450 mm including cutting for pinning in ends of brackets complete all as specified and directed

S&F 15mm bore piller taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed

S&F CP Bib taps 15mm dia, with crutch of butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, fency type and fixed complete all as specified and directed.

S&F vitreous China squatting pan, ' Orissa patteren, size 580 x 440 mm white, with integral footrests and PVC (SWR) S or P traps (excluding flushing cisteren and flush pipe) complete all as specified and directed.

S&F in repairs wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete all as specified and directed.

S&F 10 litre capacity two way flash PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete all as specified and directed.

S&F Tubular towel rail, 20mm dia, D type, brass chromium plated, 60cm long between flanges complete all as specified and directed

M&L for preparation new surface of roof and applying two coat of polyurethene (PU) acrylic based water proofing liquid compound over & including one coat of self priming primer @one litre per ten sqm with reinforcing fabric sheet as per manufactures instruction to stop leakage /seepage from roof/wall complete all as specified and directed by the Engineer-in-Charge. (Notes- 1.as per description of the items minimum two coats of polyurethene (PU) acrylic based water proofing liquid compound over one coat of primer shall be carried out by the as per manufacture instruction.pl note no price adjustment shall be made,if more coats of (PU)acrlic based water proofing liquid compound & primer are required for roof treatment. 2. quated rate shall be deemed to be included for work in building/structure of any height.)

M&L for 10mm thick in cement plaster CM (1:4) on brick or concrete surfaces finished even and fair with using water proofing compound complete all as specified and directed. (Note: WPC will be measured and paid seperately).

Supply only water proofing compond complete all as specified and directed

S&F PVC connection pipe 15mm size & 600mm long with cromium plated brass coupling on both ends suitable for 15mm bore steel tubing complete all as specified and directed

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

Taking down the existing Aluminum windows and refixing in the same opening including removal of glass/wire mesh if required and refixing to shutter frame and applying sealing compound complete all as speiified and directed (Note : New aluminum work for frame and shutter where ever necessary shall be mesured under here in after items).

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with requir etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete all as specified and directed

Excavation over areas not exc 1.5 m deep and getting out in hard / dense soil complete all as specified and directed.

All as per item No 69.00 mentioned here-in-after but depth exc 1.5 m and n. exc 3.0 m deep complete all as specified and directed.

Surface dressing n.exc 15 cm deep in soft/loose soil complete for cutting/removing of bushes, shrubs grass along the line of fencing to a distance n.exc 50 m complete all as specified and directed

M&L for brick with fly ash brick old size straight of curved on plan exc 6 m mean radius built in CM (1:4) complete all as specified and directed.

M&L for loose filling with aggregates of guage 80 to 150mm with broken bricks in soakage pits / soakage wells complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in coping including weathering throating and necessary formwork complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified and directed.

M&L precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, mangers, shelves and similar articles with plain faces and set in CM (1:6) complete all as specifed and directed. (Note: Reinforcement measured and paid sepratly)

M&L for M-25 Design mix (using 20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concret complete all as specified and directed

M&L for M-25 Design mix (using 20mm graded stone aggregate) walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed

M&L for M-25 Design mix (using 20mm graded stone aggregate) as in columns complete all as specified and directed

M&L for M-25 Design mix (using 20mm graded stone aggregate) as in beam and lintels complete all as specified and directed

M&L for M-25 Design mix (using 20mm graded stone aggregate) in slaba supported on walls, beams and column ,in roofs and shelves and the like complete all as specified and directed

M&L for M-25 Design mix (using 20mm graded stone aggregate) as in chajjas complete all as specified and directed

M&L for 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F MS Square tubue or angle iron as in half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc., and similar work conforming to Fe-290 Gd complete all as specified and directed

M&L for 100 mm thick cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) finishing smooth & even with using extra cement complete all as specified and directed .

M&L for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. Fe-410-W(Gde- E-250) quality-B complete all as specified and directed

S&F Hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcemnt complete all as specified and directed

M&L for excavating in post holes (or similar holes) soft/loose soil each n exc 0.5 cu.m. getting out, returning,filling in and ramming earth of broken rubble mixed with earth around , in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed.

Supply only Chain link MS galvanisd fencing with mesh of 75X75mm (minimum dia of wire 3mm) complete all as specified and directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed

S&F 5 to 10mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm n exc 10cm long complete all as specified and directed.

S&F capacity 1000 Ltrs rotational moulded polyethylene water storage multilayer tanks (Cylindrical, vertical with closed top) confirming to relevent IS complete including provision of all inlet outlet overflow and drain pipe fitting complete all as specified and directed by Engineer in Charge

S&F of high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 25 mm dia with fly nut complete complete all as specified and directed.

M&L for 25 mm bore gate valve cast copper alloy screwed down high pressure with clutch handle screwed both ends for Iron pipe complete all as directed.

S&F 25 mm bore GI Tubing medium grade in Trenches/ Floor/Pillar and connection including fitting like socket /Union/Tee/Reducer Nipple etc complete all as per specified and directed.

E/M PORTION M&L point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FR cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FR PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. Note : Quoted rate shall be included necesarry chasing cutting and making good disturbed surface.

All as per item No 97.00 mentioned here-in-above but One 3 pin 5 Amps socket out let points on independent board complete all as specified and directed

All as per item No 97.00 mentioned here-in-above but 5 Amp socket on same board with other switches complete all as specified and directed.

M&L for wiring for socket out let on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FR cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FR cable earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Note : Quoted rate shall be included necesarry chasing cutting and making good disturbed surface).

S&F switch piano flush type, single pole , 5/6 Amps, one way complete all as specified and directed.

S&F switch socket combination 2 in 1 multipurpose 5 pin , (6 Amps ) flush type controlled by one switch complete all as specified and directed

S&F socket outlets 2 in 1, 3 pin, 5/6 Amps flush type230/240 V complete all as specified and directed .( For Same Board only)

S&F switch socket combination 5 in 1 , 6 pin , (5/16 Amps ) flush type controlled by one switch complete all as specified.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

S&F building security light fittings 25 watts, minimumm system lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete suitable for pole dia 25mm complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as directed.

S&F 18 W LED light fitting wall mounted batten 4'ft , extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6000K including necessary connection complete all as specified and directed.

S&F epoxy powder coated sheet metal enclosure for DBs, double door , Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed.

S&F MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Voltsand to be housed in DBs including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

S&F MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection complete all as specified and directed. (Note :- Proper and suitable size cable lugs to be fixed with MCB are included in unit rate of each MCB of any rating)

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 15 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. (Note :- (i) If the desired earth resistance is not found, earthing shall be redone by the contractor at no extra cost to the department. (ii) Testing to be carried out by the contractor in presence of Engr- in- Charge , entered in the eath testing register, prepared and to be maintained by the contractor & submited to Concerned JE E/M. (iii) T&P and testing instrument(Meger) to be provided by the contractor at own cost).

S & F ventilating exhaust fan 230 mm sweep 230 volt AC complete with louver and all accessories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size all as directed.

Supply, laying / fixing / connecting, testing and commissioning of 10 sqmm x 2. core LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge . (Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely).

M&L for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling all as per SSR part-1 complete as specified and directed .

Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed by the Engr-in-Charge.

rahul enterprise

SUPARNA TRADING

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP

UNITED BUILDERS

KAZI SAHABUL ALAM